General Purpose Type
Photocoupler
LTV-4N35 Series/LTV-4N37 Series
4N35 Series/4N37 Series
Features Package Dimensions
High current transfer ratio
(CTR : MIN.100% at IF=10mA, VCE=10V)
Response time
(ton : TYP, 3 s at VCE=10V, IC=2mA, RL=100 )
Input-output isolation voltage :
LTV-4N35(Viso : 3,550Vrms)
LTV-4N37(Viso : 1,550Vrms)
UL approved (No. E113898)
TUV approved (No.R9653630)
CSA approved (No. CA91533-1)
FIMKO approved (No. 193422)
NEMKO approved (No. P96103013)
DEMKO approved (No. 303985)
SEMKO approved (No. 9646047/01-30)
VDE approved (No. 094722)
Options available :
-Leads with 0.4"(10.16mm)spacing (M Type)
-Leads bends for surface mounting(S Type)
-Tape and Reel of Type I for SMD(Add"-TA"Suffix) Note:
-Tape and Reel of Type II for SMD(Add"-TA1"Suffix) 1.Year date code.
-VDE 0884 approvals (Add"-V"Suffix) 2. 2-digit work week.
3. Factory code shall be marked (Z : Taiwan, Y : Thailand).
Applications 4. Model No.:LTV4N35 ; LTV4N37 ; 4N35 ; 4N37
1. I/O interfaces for computers. 5. All dimensions are in millimeters (inches).
PHOTOCOUPLER
2. System appliances, measuring instruments. 6. Tolerance is 0.25mm (.010 ) unless otherwise noted.
3. Signal transmission between circuits of different 7. Specifications are subject to change without notice.
potentials and impedances.
Ordering Information
Application part
Part Number Package Safety Standard Approval number
LTV-4N35 / 4N35 6-pin DIP UL approved
LTV-4N35M / 4N35M 6-pin (leads with 0.4" spacing) TUV approved
LTV-4N35S / 4N35S 6-pin (lead bends for surface mount) CSA approved LTV - 4N35
LTV-4N35S-TA / 4N35S-TA 6-pin (tape and reel packaging of type I) FIMKO approved
LTV-4N35S-TA1 / 4N35S-TA1 6-pin (tape and reel packaging of type II) NEMKO approved
LTV-4N37 / 4N37 6-pin DIP SEMKO approved
LTV-4N37M / 4N37M 6-pin (leads with 0.4" spacing) DEMKO approved
LTV-4N37S / 4N37S 6-pin (lead bends for surface mount) LTV - 4N37
LTV-4N37S-TA / 4N37S-TA 6-pin (tape and reel packaging of type I)
LTV-4N37S-TA1 / 4N37S-TA1 6-pin (tape and reel packaging of type II)
LTV4N35-V / 4N35-V 6-pin DIP VDE approved
LTV4N35M-V / 4N35M-V 6-pin (leads with 0.4" spacing)
LTV4N35S-V / 4N35S-V 6-pin (lead bends for surface mount) LTV - 4N35
LTV4N35STA-V / 4N35STA-V 6-pin (tape and reel packaging of type I)
LTV4N35STA1-V / 4N35STA1-V 6-pin (tape and reel packaging of type II)
LTV4N37-V / 4N37-V 6-pin DIP
LTV4N37M-V / 4N37M-V 6-pin (leads with 0.4" spacing)
LTV4N37S-V / 4N37S-V 6-pin (lead bends for surface mount) LTV - 4N37
LTV4N37STA-V / 4N37STA-V 6-pin (tape and reel packaging of type I)
LTV4N37STA1-V / 4N37STA1-V 6-pin (tape and reel packaging of type II)
12-33
Absolute Maximum Ratings (Ta=25 )
Parameter Symbol Rating Unit
Forward Current IF 60 mA
Input Reverse Voltage VR 6 V
Power Dissipation P 100 mW
Collector-Emitter Voltage VCEO 30 V
Collector-Base Voltage VCBO 70 V
Output Emitter-Collector Voltage VECO 7 V
Collector Current IC 100 mA
Collector Power Dissipation PC 300 mW
Total Power Dissipation Ptot 350 mW
4N35 3,550
*1.Isolation Voltage Viso Vrms
4N37 1,500
Operating Temperature Topr -55~+100
Storage Temperature Tstg -55~+150
*2.Soldering Temperature Tsol 260
*1. AC for 1 minute, R.H. = 40 ~ 60%
Isolation voltage shall be measured using the following method.
(1)Short between anode and cathode on the primary side and between collector, emitter and base on the secondary side.
(2)The isolation voltage tester with zero-cross circuit shall be used.
(3)The waveform of applied volttage shall be a sine wave.
*2. For 10 seconds.
Electrical/Optical Characteristics (Ta=25 )
Parameter Symbol Min. Typ. Max. Unit Conditions
Forward Voltage VF 1.2 1.5 V IF=10mA
Input
Reverse Current IR 10 A VR=4V
Terminal Capacitance Ct 50 pF V=0, f=1kHz
Collector Ta=25 50 nA VCE=10V
I CEO
Dark Current Ta=25 500 A VCE=30V
Collector-Emitter
BV CEO 30 V IC=0.1mA
Output
Breakdown Voltage
Emitter-Collector
BV ECO 7 V IE=10 A
Breakdown Voltage
Collector-Base
BV CBO 70 V IC=0.1mA
Breakdown Voltage
Collector IF=10mA
Ta=25 IC 10 mA
Current VCE=10V
Transfer Characteristics
*1 Current IF=10mA
Ta=25 CTR 100 %
Transfer Ratio VCE=10V
Collector-emitter
V CE(sat) 0.3 V IF=50mA, IC=2mA
Saturation Voltage
10 11
Isolation Resistance R ISO 5 10 1 10 DC500V, 40~60% R.H.
Floating Capacitance Cf 1.0 2.5 pF V=0, f=1MHz
Response Time (Turn-on Time) t on 3 10 s VCE=10V, RBE=
Response Time (Turn-off Time) t off 3 10 s RL=100 , IC=2mA
IC
*1. CTR= I F 100%
12-34
Typical Electrical/Optical Characteristic Curves
(25 Ambient Temperature Unless Otherwise Noted)
PHOTOCOUPLER
12-35
12-36
