Foldable Puzzle Mat Game Mat
Uploaded by
AaronFoldable Puzzle Mat Game Mat
Uploaded by
Aaroninstructables
Foldable Puzzle Mat (Game Mat)
by timberbiscuitwoodworks
My son has been really into puzzles lately and this portable puzzle mat and board game table locks into a lazy susan base
and was a lot of fun to build. I have seen plenty of gaming tables or puzzle boards out there, but nothing that could
easily be folded and stored. This foldable piece is beautiful, sturdy, and functional as it can be used with or without the
lazy susan base. And the folding butler hinges means we can use it pretty much anywhere. I know my son is going to love
it as he builds and plays for years to come. Let me know if you have any questions down in the comments!
Project plans: https://etsy.me/3ocCIGf
Supplies:
4/4 Hardwood of your choice
Plywood for the board and lazy susan
Butler hinges
Clasps
Handle
Table Saw
Sand Paper
Finishing Oil
Router and Bits
Lazy Susan hardware
Drill
Foldable Puzzle Mat (Game Mat): Page 1
Foldable Puzzle Mat (Game Mat): Page 2
https://youtu.be/h4KFzj2mz3w
Step 1: Mill the Lumber
1. Cut some four-quarter walnut lumber to rough length.
Foldable Puzzle Mat (Game Mat): Page 3
2. At a jointer, mill one face and one edge at.
3. With the at side down, plane the top at a planer.
Foldable Puzzle Mat (Game Mat): Page 4
Step 2: Make the Frame Pieces
1. Using a table saw, rip the board into 2" strips
2. Using a miter gauge, cut a 45 degree miter onto one side of all 4 boards
3. Flip the boards and cut a mirroring 45 degree miter onto the other side.
4. Using a ripping blade, rip a 1/2" rabbet along the inside edge of the frame.
5. Adjust the fence and make a second cut for the rabbet.
Make sure the o -cut faces away from the fence when ripping the board to avoid kick back.
6. Using a crosscut sled, cut 2 of the mitered boards in half. These will be the sides for the hinged frame.
7. Cut these to the nal length
Foldable Puzzle Mat (Game Mat): Page 5
Foldable Puzzle Mat (Game Mat): Page 6
Foldable Puzzle Mat (Game Mat): Page 7
Foldable Puzzle Mat (Game Mat): Page 8
Step 3: Routing Out the Butler Hinges
1. Use a router jig for the butler hinges. On one of the hinge frame pieces, carefully cut around the template
and remove the material for the face of the hinge.
2. Referencing the same point as the rst jig, use another to route in the deeper channel for the hinge pin.
Foldable Puzzle Mat (Game Mat): Page 9
Step 4: Cut Out Panel Pieces and Glue to Frame
1. Using 1/2" plywood (I used baltic birch), cut it down to match the dimensions of the interior frame. You
should have 2 pieces here for it to be foldable.
2. Glue the frames to the panels.
Foldable Puzzle Mat (Game Mat): Page 10
Foldable Puzzle Mat (Game Mat): Page 11
Step 5: Add the Spines
1. Raise the table saw blade so that the cut depth and cut length were equal.
2. Using a stop block, cut the grooves for my splines.
These are both for strength and added design.
3. Cut out the splines at a bandsaw for the top end cuts, then use a pull saw to remove the rest of the
Foldable Puzzle Mat (Game Mat): Page 12
material.
I used maple for the splines for contrast here, but use whatever type of hardwood you like.
4. Mark out the triangles for the splines and cut them out at the bandsaw.
5. Glue the splines into place.
6. After the glue is dry, use a ush trim saw to cut away the excess.
Make sure to cut away from the corner when trimming the spline to avoid blowing out the
corner.
Foldable Puzzle Mat (Game Mat): Page 13
Foldable Puzzle Mat (Game Mat): Page 14
Foldable Puzzle Mat (Game Mat): Page 15
Step 6: Add the Butler Hinges and Route the Frame
1. Clean up the rounded corners from the router for the butler hinges using a chisel.
2. To attach the hinge, use a self-centering drill bit to drill in pilot holes.
3. Then use a screwdriver to drive them home.
4. Clamp the hinge to the frame to hold it in place when you drill the pilot holes for the opposite side to
connect the two pieces.
5. Test the hinge's functionality.
Foldable Puzzle Mat (Game Mat): Page 16
6. Using an eighth-inch round-over bit, soften all the top edges of the frame making sure to avoid the area
where the locking clasps will go.
Foldable Puzzle Mat (Game Mat): Page 17
Foldable Puzzle Mat (Game Mat): Page 18
Step 7: Make the Locking Channel
This will connect the mat to the top of the lazy susan.
1. Route a channel to the panel's bottom to accept the woodblock on the lazy susan.
Foldable Puzzle Mat (Game Mat): Page 19
Step 8: Make the Lazy Susan
1. Cut out the two blocks that will lock the mat for the lazy season using a bandsaw.
these are cut to the width and depth of the previously routed panel.
2. Check the t into the routed panel.
3. Cut out the edge banding at the table saw.
4. Cut the top and bottom square for the lazy susan.
I used walnut plywood since I had some leftover from another project, but use whatever
plywood you would like here.
Using a square shape for this base will help improve its stability.
5. Glue up the edge banding to the base.
Use a ush trim saw to remove any excess banding.
6. Sand all of the banded sides
7. Mark the center point for the top of the lazy susan.
8. Mask o the edges of the blocks and then glue and clamp them in place.
The tape minimizes the glue cleanup
9. Mark out the placement for the lazy susan hardware.
10. Drill pilot holes for the mounting screws.
11. At the drill press, plunge the hole in the lazy season bottom for the access point.
Foldable Puzzle Mat (Game Mat): Page 20
Foldable Puzzle Mat (Game Mat): Page 21
Foldable Puzzle Mat (Game Mat): Page 22
Foldable Puzzle Mat (Game Mat): Page 23
Foldable Puzzle Mat (Game Mat): Page 24
Foldable Puzzle Mat (Game Mat): Page 25
Step 9: Sand and Apply Finish to the Pieces
1. Sand all pieces up to 180 grit. (220 if you are not using Rubio Monocoat)
2. Wipe down everything with mineral spirits.
3. Add nish of choice to all of the pieces.
I used Rubio Monocoat and applied it with a Scotch-Brite pad making sure to wipe away
any excess.
Avoid nishing any areas where you are going to place glue down.
Foldable Puzzle Mat (Game Mat): Page 26
Foldable Puzzle Mat (Game Mat): Page 27
Step 10: Felt the Play Area
1. Make an MDF cutout or template for your playing space.
2. Using a rotary cutter, cut out the felt to its proper size.
3. Apply a thin layer of contact cement to the felt and board and press the felt onto the board.
It is easiest to remove the butler hinges for this part to glue up each panel separately.
4. With the felt down, go back with a roller to ensure the felt has no bubbles.
5. Trim any excess felt with a rotary cutter.
Foldable Puzzle Mat (Game Mat): Page 28
Foldable Puzzle Mat (Game Mat): Page 29
Foldable Puzzle Mat (Game Mat): Page 30
Step 11: Assemble the Game Board
1. Attach the lazy susan hardware to the panels.
2. Reattach the butler hinges to the frame.
3. Apply double-sided tape to the back of the clasps and the handle (this will help to mark out the screw
holes).
4. Use a reference square to make sure they sit vertically.
5. Mark the hole placement with an awl for the clasps and handle.
Foldable Puzzle Mat (Game Mat): Page 31
6. Drill in the pilot holes.
7. Drive in the screws for the clasps and handle.
I used a small screwdriver meant for electronics since the screws were so small.
Enjoy your new game board!
Foldable Puzzle Mat (Game Mat): Page 32
Foldable Puzzle Mat (Game Mat): Page 33
Foldable Puzzle Mat (Game Mat): Page 34
Foldable Puzzle Mat (Game Mat): Page 35
Lovely build, it's given me some ideas.
Is the lazy substance removed when folding for storage? Is there room inside the closed board to
store it?
The lazy susan is removable and stores separately. And locks into the puzzle board when in use.
