Harman Kardon Service Manual

Onyx Mini
Bluetooth Speaker System with built-in battery and speakerphone
SKU:
HKONYXMINIBLKAM, HKONYXMINIWHTAM, HKONYXMINIGRYAM, HKONYXMINIBLUAM, HKONYXMINIREDAM,
HKONYXMINIBLKEU, HKONYXMINIWHTEU, HKONYXMINIGRYEU, HKONYXMINIBLUEU, HKONYXMINIREDEU,
HKONYXMINIBLKAS, HKONYXMINIWHTAS, HKONYXMINIGRYAS, HKONYXMINIBLUAS, HKONYXMINIREDAS,
HKONYXMINIBLKCN, HKONYXMINIWHTCN, HKONYXMINIGRYCN, HKONYXMINIBLUCN, HKONYXMINIREDCN,
HKONYXMINIBLKJP, HKONYXMINIWHTJP, HKONYXMINIGRYJP, HKONYXMINIBLUJP, HKONYXMINIREDJP,
HKONYXMINIBLKG1, HKONYXMINIWHTG1, HKONYXMINIGRYG1, HKONYXMINIBLUG1, HKONYXMINIREDG1,
HKONYXMINIBLKG1US, HKONYXMINIWHTG1US, HKONYXMINIGRYG1US, HKONYXMINIBLUG1US,
HKONYXMINIREDG1US, HKONYXMINIBLKG2, HKONYXMINIWHTG2, HKONYXMINIBLKG2US,
HKONYXMINIWHTG2US, HKONYXMINIBLKAG, HKONYXMINIWHTAG, HKONYXMINIGRYAG, HKONYXMINIBLUAG,
HKONYXMINIREDAG, HKONYXMINIBLKAG2, HKONYXMINIWHTAG2.

CONTENTS
Page
Safety Instruction, Warning & Notes….……………………....….....2
Technical Specifications…………....………………………..............5
Set Block Diagram …………..……………………….....……..….….6
Dismantling Instruction ..........................…………………....….…..7
Circuit Diagrams ....................................…………………....….…..8
Layout Diagrams .................…....................................................16
Set Mechanical Exploded view …................………........…..........18
Packaging Exploded view………................................…….....….19
Spare Part list……...........................................……………...........20
Revision List.................................................................................22

Released Globel Quality Harman Consumer Group, Inc. Rev. 1.0 08/2016
8500 Balboa Boulevard
Northridge, California 91329
 
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions. CAUTION
3. Heed all warnings.
4. Follow all instructions. RISK OF ELECTRIC SHOCK. DO NOT OPEN.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings.Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one THE LIGHTNING FLASH WITH AN ARROWHEAD SYMBOL,
wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for ALERT THE USER TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S
replacement of the obsolete outlet. ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged TRIANGLE IS INTENDED TO ALERT THE USER TO
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the THE PRESENCE OF IMPORTANT OPERATING AND
apparatus, or the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped. MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, LITERATURE ACCOMPANYING THE PRODUCT.
are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC
receptacle. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
17. The mains plug of the power supply cord shall remain readily operable. SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
18. Do not expose batteries to excessive heat such as sunshine, fire or the like.

For Products That Transmit and For Canadian Model Caution:

Receive RF Energy: This Class B digital apparatus complies with Canadian This product uses a laser system. To prevent direct exposure
ICES-003. to the laser beam, do not open the cabinet enclosure or defeat
FCC Regulations (USA Only) any of the safety mechanisms provided for your protection.
DO NOT STARE INTO THE LASER BEAM. To ensure proper use
FCC Information For Users Modèle pour les Canadien of this product, please read the owner’s manual carefully and
This device complies with Part 15 of the FCC Rules. Operation retain it for future use. Should the unit require maintenance
Cet appareil numérique de la classe B est conforme à la or repair, please contact your local Harman Kardon service
is subject to the following two conditions: (1) This device norme NMB-003 du Canada.
may not cause harmful interference; and (2) this device must center. Refer servicing to qualified personnel only.
accept any interference received, including interference that
may cause undesired operation. For Products with Radio Receivers For Products That Include Batteries:
Radio and Television Interference That Can Use an External Antenna:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
CATV or Antenna Grounding
of the FCC Rules. These limits are designed to provide If an outside antenna or cable system is connected to this
reasonable protection against harmful interference in a product, be certain that it is grounded so as to provide some
residential installation. This equipment generates, uses and protection against voltage surges and static charges. Section
can radiate radio frequency energy and, if not installed and 810 of the National Electrical Code, ANSI/NFPA No. 70-1984,
used in accordance with the instructions, may cause harmful provides information with respect to proper grounding of the Instructions for Users on Removal and Disposal of
interference to radio communications. However, there is no mast and supporting structure, grounding of the lead-in wire Used Batteries.
guarantee that interference will not occur in a particular to an antenna discharge unit, size of grounding conductors, CAUTION
installation. If this equipment does cause interference to radio location of antenna discharge unit, connection to grounding
or television reception, which can be determined by turning electrodes and requirements of the grounding electrode. Risk of explosion if battery is incorrectly replaced.
the equipment off and then on, the user is encouraged to try Replace only with the same or equivalent type.
to correct the interference by one or more of the following Note to CATV System Installer: Alkaline batteries are considered nonhazardous.
measures:
This reminder is provided to call the CATV (cable TV) system Rechargeable batteries (i.e., nickel cadmium, nickel metal-
• Increase the separation between the equipment and installer’s attention to article 820-40 of the NEC, which hydride, lithium and lithium-ion) are considered hazardous
receiver. provides guidelines for proper grounding and, in particular, household materials and may pose an unnecessary health
• Connect the equipment to a different outlet so that the specifies that the cable ground shall be connected to the and safety risk.
equipment and receiver are on different branch circuits. grounding system of the building, as close to the point of
cable entry as possible. In the European Union and other locations, it is illegal to
• Consult the dealer or an experienced radio/TV technician dispose of any battery with household trash. All batteries
for help. must be disposed of in an environmentally sound manner.
NOTE: Changes or modifications not expressly approved For CD/DVD/Blu-ray Disc™ Players: Contact your local waste management officials for information
by Harman could void the user’s authority to operate the regarding the environmentally sound collection, recycling and
equipment. disposal of used batteries.
To remove the batteries from your equipment or remote
IC Statement and Warning (Canada Only) control, reverse the procedure described for inserting
This Class B digital apparatus complies with Canadian ICES- batteries in the owner’s manual.
003. Cet appareil numérique de la classe B est conforme à la For products with a built-in battery that lasts for the lifetime of
norme NMB-003 du Canada. the product, removal may not be possible for the user. In this
case, recycling or recovery centers handle the dismantling of
the product and the removal of the battery. If, for any reason, it
becomes necessary to replace such a battery, this procedure
must be performed by authorized service centers.
 

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and

semiconductor "chip" components.

The following techniques should be used to help reduce the incidence of component damage caused by static electricity.

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on

your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to

prevent electrostatic charge build-up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges

sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement

ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the

chassis or circuit assembly into which the device will be installed.

CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together

or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.

Each precaution in this manual should be followed during servicing.

Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with

, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the

parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably

insulated from the supply circuit before retuming the product to the customer.
 

SAFETY PRECAUTIONS

The following check should be performed for the continued

protection of the customer and service technician.

LEAKAGE CURRENT CHECK

Measure leakage current to a known earth ground (water

pipe, conduit, etc.) by connecting a leakage current tester
between the earth ground and all exposed metal parts of the
appliance (input/output terminals, screwheads, metal
overlays, control shaft, etc.). Plug the AC line cord of the
appliance directly into a 120V AC 60Hz outlet and turn the
AC power switch on. Any current measured must not exceed
o.5mA.

Reading should
not be above
Leakage
0.5mA
Device current
under tester
test

Test all
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter Earth
plug as required) ground

AC Leakage Test

ANY MEASUREMENTS NOT WITHIN THE LIMITS

OUTLINED ABOVE ARE INDICATIVE OF A
POTENTIAL SHOCK HAZARD AND MUST BE
CORRECTED BEFORE RETURNING THE APPLIANCE
TO THE CUSTOMER.
TECHNICAL SPECIFICATIONS
 HK Onyx Studio Mini Block Diagram (Reference)
I2S TI
TI
AuxͲINport DAC L&R ClassD
Audio
PCM5121 TPA3130
detect
2x8W
I2C
ANT

BTmodule TCA1116 LEDs 4ohm x2

BM970H I/OExpander OPNJM2740or
AudioSwitch I2C Buttons BA4510*3PCS
SD20 CSR8670+LNA
Noexternalflash PowerButton
MICx1
GPIO
GPIOs Logic
Audio Signal:
SLG46140
Power Signal:
DCDetect

BATTTDetect
Control Signal:

USBD+D
USB D+ DͲ
D

upgrade

DCͲDCboost
SW 5.15~11.7Vforamplifier
MicroUSBport Battery TPS61088withSW
Charger
USB5V BQ24297 3.3Valwaysonfor
LDOͲ3.3V
SGM2306 SLG46140
Battery
3.7V/3000mAh LDOͲ3.3VwithSW
SW 3.3VforDACandOP
ACadaptor
p SGM2306
5V/2.3A
LDOͲ3.3V
SGM2306 3.3VI/Oexpander/BT

HARMAN INTERNATIONAL. CONFIDENTIAL. COPYRIGHT 2014. 2

DISMANTLING INSTRUCTIONS

1,Disassemble Fabric Bracket

2,Disassemble 4pcs Sleeveand Loosen 3,Disassemble mic ˈButton Ring and
4pcs screws Speaker Cable

4,Loosen 4pcs Main PCBA screws,disassemble 5,Disassemble 2pcs drivers , mic and 6,Loosen 3pcs bottom screw ,bottom cover and
Power CableˈMicro USB+AUX Cable and Passive radiator,Loosen 6pcs screw 1pcs USB PCBA screw
Antenna
 6 5 4 3 2 1

$8;B/,1
73 73 73

& X)
)% .RKP 5 .  $8;B/
& X)
)% .RKP 5 .  $8;B5

hœŸGp•—œ› 

& & 5
 5  & & 5 '$&B9
D D
 S) .
73 86%B'  Q) Q) S)
. &
Q)
73  9 9 $8;B5,1
86%B'
- 9
& &

2
8

ESD1

ESD2
S) S)  

1
ESD ESD 9&& 12
0,&B$B3   0,&B53
12 &20
0,&B/3   5 . $8;B0,&B&75
&20 ,1
  $8;B5
,1 1&
$8;B/  
1& *1'
5
.
6'
 5  5 0,&B%,$6
& &
X) X)
9 9 /2*,& 12 1&

5
/ 2)) 21
73 / .
Q+
 & Q) 0,&B$B3
 9
+ 21 2))
2

- 5
ESD3

73 & 5 & &

S) S) S)
1

C C
ESD

& X) 0,&B/1

9
& X) 0,&B51
9

/ .RKP %7B9&&
5 1& '$&B9

&

.
5
Q) .
5 73
0

5

5
4 
6&*5 $8',2B'(7

5 & 9

$8;B/,1 
X) ' 4
5

&
. Q)
& X)
%$7&7 6&*5
5
9

B
.

.
5

5
0

$8;B5,1 5 
& 9
X)
4 Aux Detector
6&*5

A A

CUSTOMER: Harman
COMPANY:

SHEET: AUX_IN_MIC REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 2 OF 9

 6 5 4 3 2 1

D D

 
*3,2 *3,2
5   
$'5 *3,2
  5  ,&B6&/
02'( 6&/

86%B9B,1B'(7
'$&B9&& 5    5  ,&B6'$
02'( 6'$
  5  '$&B9&&
*3,2 9&20
&KDQJHG&IURPX)WR525
5    5 1& %7B9
6&. $*1'
,6B%&/. 5    / .RKP '$&B9
%&. $9''
,6B'$7$ 5    5 . $8',2B287B5
',1 2875
5   3&0  5 . $8',2B287B/
,6B/5&. /5&. 287/
5    & & & &

5

5

5

5
$'5 91(* Q)
X) Q) Q)


5 .   & X)
;607 &$30 9 9
9

.

.

1&

1&
 

5
/'2B2 &3*1'
& & 8
  X) Q)
'*1' &$33 6/*99

*3,2 

*3,2 
'$&B9&&     9 9
'9'' &39'' 4
1&

'

'
& & & & & & & 4
 
9&&B9 5   9'' *3,2 
X) Q) X) Q) X) Q) X) 1& 5 1& 5 1& *$,1B&75 5 .
8

6
* *
9 9 9 9 9 9
32:(5B.(< 5   *3, *3,2  5  95(*B(1
9  

5

5
C C
'&B%,$6 5   *3,2 *3,2 
32:(5B21B2)) 5 . 5   *3,2 *3,2  5  32:(5B21

1&

1&
32:(5B2))B5($'< 5   *3,2 *1' 

 *3,2

 *3,2
73
5  5 .
& S)
5
5 . ' 1:7

5  
5  '$&B9
'$&B9 & &
Q) 5
& X)
Q) .
9 9
9


 ,1


$8',2B287B5 & X) 5 .  ,1

9&&
287

9 9&&  & X)  *1'

'$&B9
287 ,1
BIAS 5 .  *1' 8$
9


,1
8$ 1-09


1-09 BIAS 5 .

& S)

5 . ' 1:7

B $8',2B287B/ & X) 5 . 

 ,1
 B
,1 287
9 287
 & X)  ,1
BIAS 5 .  8%
,1 9
8% 1-09
1-09 BIAS 5 .

5  73
73

' 1:7
5  5 . $
5 
'$&B9 5
& & &
X) Q) X)
5 .
'$&B9 
9 9 9
5 '$&B9 5 . %,$6


 ,19&&
 0 & & & &

.

287 X) Q) X) Q)
$8',2B287B5 & X) *1'
,1
8$ 9 9 9 9
9


1-09

5
BIAS 5 .

' 1:7

 ,1
287

$8',2B287B/ & X)  ,1
8%
A
9
1-09
BIAS 5 . A

CUSTOMER: Harman
COMPANY:

SHEET: DAC_DYNAMIC_VOLTAGE REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 3 OF 9

 6 5 4 3 2 1

D D

9B$03B9 5
9B$03B9


& &
Q) & & X)
5
9 Q)
Q) 9
. 9

& 
8
$03B6'= 5  % 4 &
5
. /0%7/7 Q)
9 73$''$35

 (
/

  X+ &
02'6(/ 39&& & Q)
&
73   X) Q) 
6'= 39&&
& 

)$8/7= %635

Q)
5 
-
RKP:
5 &   5 
$8',2B287B5 X) 5,13 28735
 & &
  &
X) 5,11 *1' &
X) Q)
  Q)
3/,0,7 28715
C 
*9'' %615
 & /
5
C
Q)
  X+ /
5 5
*$,16/9 *1'
  & /
 . *1' %63/
Q)
  X+ & &
& & /,13 2873/ &
9 Q) Q) 
1& X)   X) 
5 5 /,11 *1'
5 
1& .  
73

087( 2871/
 &
5 
-
RKP:
&
$0 %61/ & Q)
Q) &
  Q)
5 & $0 39&& X)
$8',2B287B/
 

/
 X) $0 39&& /
&  
6<1& $9&& X+

3$'
X)


%$7&7

73
%7B9 .
5
9B$03B9
9B$03B9
'
& 

& &
Q) & X)
$03B087( 5  % 4
Q) 9
. /0%7/7 5
9
 (

& 1&
5

. Q)
9

B B
73

73

73 73 73 73

A A

CUSTOMER: Harman
COMPANY:

SHEET: POWER_AMP REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 4 OF 9

 6 5 4 3 2 1

5 5 5 5 5

     
/('B:+,7(

D /('B:+,7( D
/('B:+,7(

/('B:+,7(

/('B:+,7(

5
-
/('B5('
$17&21 / %7B9
%7B9&&


5

5

5

5

5

 5
Q+


/

.

.

.

.

.

3

3

3

3

3

3
5)B7(67 .
&
1& .(<B%7 5 . ,2B5(6(7
3 567

1&

 
3 $
From ANT with RF Cable  
*1' ,17 ,2B,17 ,2B9
 
.(<B3+21( 5 . 3 9&& / .RKP %7B9
5 .  8 
*3,2 5 . 7&$57:5
.(<B92/ 3 6'$ & & & &

ESD4
5 . Q) Q) Q)

2
  X)
*3,2 5 .
.(<B92/ 3 6&/
 3'  9 9 9 9
%7B9&& / RKP

1
 ESD

3

3

3

3

3

$
&
Q)












9 &+$5*(B67$786 5 .

5 1& 5  ,&B6'$

*$,1B&75




















5  ,&B6&/
%7B9 5 1&

*1'

9''B9

*3,2B

*3,2B

*1'

5)B,1

*1'

*1'

63.B53

63.B51
C 5 . ,2B9
C
63.B/3

& 
5
$,2 

9%$7B'(7  % 4
$,2 63.B/1 1&
  1&

 (
*1' *1'
 
,6B%&/. 0,&B%,$6
,6B%&/. 0,&B%,$6B$
 
,6B/5&. ,6B/5&/. 0,&B%,$6B%
 
,6B'$7$ ,6B'$7$287 0,&B/3 0,&B/3
 
,6B'$7$,1 0,&B/1 0,&B/1
 
*1' 0,&B53 0,&B53
 
63,B&/. 63,B&/. 0,&B51 0,&B51
 
63,B0,62 5 . %7B9&&
63,B0,62 *1'
 
%7B9&& 63,B&6% . 5 86%B9B,1B'(7
73 63,B&6% *3,2
 
63,B&6% 63,B026, 5  &+$5*(B,17
73 63,B026, *3,2
 
63,B&/. *1' *3,2 95(*B(1
73 8
 
63,B026, %7B9&& 5 . %0+ 86%B9B,1
73 5(6(7 9
& &  
63,B0,62 X) Q)
73 8$57B576 &+*B(;7
 
9 9 %7B9&&
73 8$57B&76 9%$7B6(16(
 
/  %7B9
8$57B5; 9%$7
  
%7B9 & & &
8$57B7; 9B287 Q) Q)  &
  X)
B 32:(5B/('

1&
/(' 9''B0(0
B


& 9 9 9 X)
  9
%7B/(' /(' 9''B3$'6 Q)

5

5
  9
3+21(B/(' /(' *1'
 
*3,2 5  86%B'
*3,2 86%B'
 
5  86%B'
32:(5B2))B5($'< ,&B6'$ 86%B'
 
32:(5B21B2)) ,&B6&/ *1'
 
,&B6'$
32:(5B67%< *3,2 ,6B%&/.
 
,&B6&/
,6B'$7$,1 ,6B/5&/.
 
,2B5(6(7 .RKP )%
,6B'$7$287 *3,2
 
5 .
*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

*3,2

%7B9&& . .

*1'

5 5




























%7B9&&
,2B,17

$8',2B'(7
$03B6'=

$03B087(
*3,2
$8;B0,&B&75
'$&B67%<

A A

CUSTOMER: Harman
COMPANY: BT_CTR
SHEET: REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 5 OF 9

 6 5 4 3 2 1

9RXW  5)5) 9

73


& Q) 
%227 9287  6 '  9B$03B9
9 ' '
/ 9287  ' 

5



*
9B%$77(5<  6: 9287  

1&
4 &
X+  6:  &

.
96+ Q)

.

&
5 1&  6: 9 X)

D 5 1&  6: )% 
9
D

&

5

5
.


& 1& &
& & & X)

1&
5 .  )6:

5
Q)


& X) X) X) 9
 &203  5 .
9 9 9
 9 5 . 5 . '&B%,$6
 9,1

,/,0  5 .

.
 9&&
& Q)
66 

& 
5 .  (1

5 5
32:(5B67%<
9

 
5
4 %  32:(5B67%<
& & & 02'(  5 1& /0%7/7 .

 (
X) X) & X)  3*1'
Q)
9 9 9 9 1&  5

.
 $*1' .
1& 

8
736B'&'&B94)1

C C
73
8
/ .RKP  9,1  9&&B9
9287

 *1'
&  &
X) & &( %<3  X) &
Q)
9 96. 9 Q)
9
9

73
8
 /
/ .RKP  9,1 9287 '$&B9
 .RKP 
 *1'
&  &
X) & &( %<3  X) &
Q) 5
9 96. 9 Q)
9
9
.

5 '$&B67%<
.

73
8
9B%$77(5< ' 6  9,1  /  %7B9
9287
B

&

*

B


&  *1'
4 X) &
Q)


 X) &
96
& 9 9 &( %<3  Q)

.

9 9
.

Q) 96.
5

5


1:;73

4
& 

/0%7/7
5
32:(5B21  %
.
 (

'

&

Q)

5 .

5 1:;73 ' 86%B9B,1

.
.
5
& 

4 % 
/0%7/7
 (

A 5
. A

CUSTOMER: Harman
COMPANY: POWER_SUPPLY
SHEET: REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 6 OF 9

 6 5 4 3 2 1

D D

5
86%B9B,1B'(7
.

.
.

5
5
86%B9B,1
9B5(*1
73
5  & Q)
& 9
& /


X)
& X) & Q)
Q)

9
9 9
9 X+

)%
&

X)
&
X) &
5 Q)
9 9


C 73
C














3:3$'

30,'

5(*1

%767

6:

6:
9%86
-
 )%  
9%86 3*1'
 RKP
& &  
' 3*1'
& Q) & Q) &
Q) Q)  8 
X) & ' 6<6
9 9 Q) %4
  73
9 9 67$7 6<6

5   
6&/ %$7

5    9B%$77(5<
6'$ %$7

5
&

421
86%B'

27*

,/,0
,17
X) & &

&(

76

9
Q) X)
3.7V/3000mAH Li-lon






9
73
5 
86%B' 
 

5 
9B5(*1
&+$5*(B67$786 5
73 73 . 9B5(*1 -



5 5 . 73
&

5

5
,&B6&/ 1&  Q)


.
9 
B ,&B6'$

&+$5*(B,17 B

4 96
ILIM=(1/RILIM)*435=2.1A ' 6


*

ICHG=I2S Set=2.048A


.

.
.
5

5

5

4
9%$7B'(7

& 
/0%7/7
5 .
5 & %  %7B9

.
. Q)

 (


5
A A

CUSTOMER: Harman
COMPANY: CHARGE
SHEET: REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 7 OF 9

 6 5 4 3 2 1

D D

73
5  /(' :KLWH 32:(5B/('
%7B9

6
  .(<B92/


73
5  /(' :KLWH %7B/('
6
  .(<B92/


73
5  /(' :KLWH 3+21(B/('

6
  .(<B%7

73
C 6 C
  .(<B3+21(


/(' :KLWH
/('B:+,7(

73
/(' :KLWH
/('B:+,7(

6
  32:(5B.(< /(' :KLWH
/('B:+,7(


/(' :KLWH
/('B:+,7(

/(' :KLWH
/('B:+,7(

/(' 6XSHU5HG
/('B5('

B B

A A

CUSTOMER: Harman
COMPANY: KEYS_LEDS
SHEET: REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.schSHEET: 8 OF 9

 6 5 4 3 2 1

D D

C C

73 73 73 73 73 73 73

- -
9&&    3-
'1   
'3   
*1' 1&  
  
1&
1&
1&

*1'
 -







-
/ RKP

B 3&% B

A A

CUSTOMER: Harman
COMPANY:

SHEET: JACK REV: V4

FILENAME: Harman Onyx mini _SCH V4_20160616.sch

SHEET: 9 OF 9
LAYOUT DIAGRAM - MAIN BOARD
LAYOUT DIAGRAM - USB JACK BOARD
 1 2 3 4 5 6 7 8 9

A A

B B

C C

THIRD ANGLE PROJECTION

D D

1 2 3 4 5 6 7 8 9
HK ONYX MINI SPARE PARTS LIST
Pos. No. Part Number Description QTY
1+7+11 SA-HAR023CA0012-C BACK HOUSING BACK ASSY BLK ONYX MINI 1
1+7+11 SA-HAR023CA0013-C BACK HOUSING BACK ASSY WHT ONYX MINI 1
1+7+11 SA-HAR023CA0014-C BACK HOUSING BACK ASSY RED ONYX MINI 1
1+7+11 SA-HAR023CA0015-C BACK HOUSING BACK ASSY GRY ONYX MINI 1
1+7+11 SA-HAR023CA0016-C BACK HOUSING BACK ASSY BLU ONYX MINI 1
2 EA-PL0640XM0001-C PASSIVE RADIATOR BACK BLK 1
2 EA-PD0640XM0001-C PASSIVE RADIATOR BACK WHT 1
2 EA-PD0640XM0003-C PASSIVE RADIATOR BACK RED 1
2 EA-PD0640XM0004-C PASSIVE RADIATOR BACK GRY 1
2 EA-PD0640XM0005-C PASSIVE RADIATOR BACK BLU 1
3 SA-HAR023PA0001-C MAIN PCBA ONYX MINI 1
4 SA-HAR023PA0006-C USB JACK PCBA ONYX MINI 1
5 MR-HAR023A00002-C Rubber_Foot BLK 1
5 MR-HAR023A00007-C Rubber_Foot WHT 1
5 MR-HAR023A00008-C Rubber_Foot RED 1
5 MR-HAR023A00009-C Rubber_Foot GRY 1
5 MR-HAR023A0000A-C Rubber_Foot BLU 1
6 MP-HAR023A00002-C
MP HAR023A00002 C Cover_Bottom
C B 1
8 MP-HAR023A00003-C LI-ION BATTERY_Box 1
9 ET-BL0423000001-C LI-ION BATTERY 1
13 MP-HAR023A00001-C Housing_Front BLK 1
13 MP-HAR023A00005-C Housing_Front WHT 1
13 MP-HAR023A00006-C Housing_Front RED 1
13 MP-HAR023A00007-C Housing_Front
g_ GRY 1
13 MP-HAR023A00008-C Housing_Front bule 1
14 EA-PD0640XX0001-C Passive radiator front BLK 1
14 EA-PD0640XM0002-C Passive radiator front WHT 1
15 EA-FD0415NF0001-C Full range driver 2
17+18 SA-HAR023CA000D-C FABRIC BRACKET ASSY BLK 1
17+18 SA-HAR023CA000E-C FABRIC BRACKET ASSY WHT 1
17+18 SA-HAR023CA000F-C FABRIC BRACKET ASSY RED 1
17+18 SA-HAR023CA0010-C FABRIC BRACKET ASSY GRY 1
17+18 SA-HAR023CA0011-C FABRIC BRACKET ASSY BLU 1
19 MM-HAR023000001-C Logo BLK 1
19 MM-HAR023000002-C Logo WHT 1
19 MM-HAR023000003-C Logo RED 1
19 MM-HAR023000004-C Logo GRY 1
19 MM-HAR023000005-C Logo BLU 1
20 MR-HAR023A00001-C Button_Ring BLK 1
20 MR-HAR023A00003-C Button_Ring WHT 1
20 MR-HAR023A00004-C Button_Ring RED 1
20 MR-HAR023A00005-C Button_Ring GRY 1
20 MR-HAR023A00006-C Button_Ring BLU 1
22 MP-HAR023A00004-C
MP HAR023A00004 C SLEEVE BLK 4
22 MP-HAR023A00009-C SLEEVE WHT 4
22 MP-HAR023A0000A-C SLEEVE RED 4
22 MP-HAR023A0000B-C SLEEVE GRY 4
22 MP-HAR023A0000C-C SLEEVE BLU 4
EW-MA10001400-B MICRO USB CABLE 1
EA-MD0040CD0003-C MICROPHONE 1
ET TU0500230001 C
ET-TU0500230001-C ADAPTOR ONYX MINI 1
ET-TU0500230002-C ADAPTOR EMEA ONYX MINI 1
EG-000000DA00-B ADAPTER PLUG-UK 1
EG-000000DB00-B ADAPTER PLUG-EU 1
PG-HAR023000008-C GIFT BOX EMEA_BLK 1
PG-HAR023000009-C GIFT BOX EMEA_WHT 1
PG-HAR02300000A-C GIFT BOX EMEA_RED 1
PG-HAR02300000B-C GIFT BOX EMEA_GRY
EMEA GRY 1
PG-HAR02300000C-C GIFT BOXEMEA_BLU 1
REVISION LIST

Version 1.0
γ

 Initial Release for HK ONYX MINI