Scribd
Upload
44 views

Experiment No: 3 Interfacing Temperature Sensor LM35

This document describes an experiment to interface a temperature sensor (LM35) with a Node MCU microcontroller. The LM35 is a precision temperature sensor that outputs an analog voltage proportional to the measured temperature. It can measure temperatures from -55°C to 150°C. The document outlines the components needed, including the LM35, Node MCU, breadboard, and connecting wires. It also provides the circuit diagram and Arduino code to read the analog output from the LM35 sensor and convert it to a Celsius temperature reading, which is printed to the serial monitor. The code samples the LM35 every second and also calculates and displays the temperature in Fahrenheit.

Uploaded by

WAGHULE SHUBHAM
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
44 views

Experiment No: 3 Interfacing Temperature Sensor LM35

This document describes an experiment to interface a temperature sensor (LM35) with a Node MCU microcontroller. The LM35 is a precision temperature sensor that outputs an analog voltage proportional to the measured temperature. It can measure temperatures from -55°C to 150°C. The document outlines the components needed, including the LM35, Node MCU, breadboard, and connecting wires. It also provides the circuit diagram and Arduino code to read the analog output from the LM35 sensor and convert it to a Celsius temperature reading, which is printed to the serial monitor. The code samples the LM35 every second and also calculates and displays the temperature in Fahrenheit.

Uploaded by

WAGHULE SHUBHAM
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Experiment No: 3

Interfacing Temperature Sensor LM35

Name of the Student: ____________________ _______ Div. & Roll No.______

Aim: To interface temperature sensor LM35 with Node MCU


Components Required:

1) Node MCU – 1
2) Micro USB Cable – 1
3) PC/Laptop – 1
4) Connecting Wires
5) Bread Board – 1
6) LM35 – 1

Software Required:

Arduino IDE

Theory:

In this experiment, we will see how to connect temperature sensor LM35 with Node MCU and
how to measure temperature using analog pin of ESP8266 Node MCU. In general, an LM35 is a
temperature sensor which is designed specifically to measure the hotness or coldness of an
object.

LM35 is a precision IC temperature sensor with its output proportional to the temperature (in
°C).

With LM35, the temperature can be measured more accurately than compared to the thermistor.

In this experiment, LM35 is used to measure the Room Temperature.

1
LM35 temperature sensor

LM35 is a temperature sensor that can measure temperature in the range of -55°C to 150°C.

It is a 3-terminal device that provides an analog voltage proportional to the temperature. The
higher the temperature, the higher is the output voltage.

The output analog voltage can be converted to digital form using ADC so that a microcontroller
can process it.

Procedure:

Step 1: Make the circuit diagram on bread board according to connection diagram shown below.
Pin 1 of the LM35 goes into +3.3v[3V3 Pin] of the Node MCU. Pin 2 of the LM35 goes into
Analog Pin [A0] of the Node MCU. Pin 3 of the LM35 goes into Ground Pin (GND) of the
Node MCU.

Before getting the Celsius reading of the temperature The analog output voltage from LM35
must first be read from the Vout pin of LM35.This will be the raw value divided by 1024 times
3300. It is divided by 1024 because a span of 1024 occupies 3.3v. Here we get the ratio of the
raw value to the full span of 1024 and then multiply it by 3300 to get the millivolt value. Since
the output pin can give out a maximum of 3.3 volts (1024), 1024 represents the possible range it
can give out.

Step 2: Connect Node MCU to PC / Laptop with the help of micro USB cable
2
Step 3: Open new Sketch, Go to file ----> New

Step 4: Write following code in new sketch

//initializes/defines the output pin of the LM35 temperature sensor


int outputpin = A0;
//this sets the ground pin to LOW and the input voltage pin to high
void setup ()
{
Serial.begin(9600);
//Setting the baud rate for Serial Monitor Communication
}

void loop() //main loop


{
int analogValue = analogRead(outputpin);
float millivolts = (analogValue/1024.0) * 3300; //3300 is the voltage provided by NodeMCU
float celsius = millivolts/10;
Serial.print("in DegreeC= ");
Serial.println(celsius);

//---------- Here is the calculation for Fahrenheit ----------//


float fahrenheit = ((celsius * 9)/5 + 32);
Serial.print(" in Farenheit= ");
Serial.println(fahrenheit);
delay(1000);
}

Step 5: Save the new sketch by appropriate name in a folder on your PC / Laptop

Step 6: Upload the sketch on Node MCU. Go to Sketch ----> Upload

3
Step 7: Observe the output by clicking on Serial Monitor icon on the upper right corner of
Arduino IDE. [Room Temperature]

Step 8: Hold LM35 tightly in your hand and observe the change in the temperature reading
sensed by it.

Practice:

1. Interface LM35 and Buzzer both, to Node MCU. Modify the sketch such that buzzer
should beep after temperature increases or decreases beyond certain value

Conclusion:

______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________

You might also like