SL. NO.

SHORT DESCRIPTION

1 Central AC Material Rate

2 INSTALLATION Rate
Total Amount =
 TOTAL
AMOUNT
(BDT)
61,745,666.19
12,890,685.90
74,636,352.09

SL. NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19

Total Am
 Imported material Local material Installation
SHORT DESCRIPTION
Price Price Price
Chiller 7,108,051.00
AHU & FCU 8,497,006.00
Pump 9,238,200.00
Cooling Tower 4,000,000.00
Central Monitoring System
Pipe & accessories 3,193,060.98
Pipe Insulation 686,212.78
Room Thermostat 1,280,027.00
Drain Pipe with insulation 96,820.00
VALVE ACCESSORIES 4,394,205.39
Ventilation Fan 2,991,080.00
Air Terminal 1,042,888.01 1005795
Ducting Work 5,148,128.52 48667.5
Electromagnetic Flow Meter: -
EXPANSION TANK (Close Type) : 328,700.00
WATER SOFTNER PLANT : 908,250.00
Dirt and Air separator : 2,175,475.00
MAKE-UP WATER TANK WITH
55,000.00
FLOAT VALVE:
Chemical Dosing System: 198,950.00

Total Amount = 47,365,960.91 5030556.256

 United Property Solutions Limited
HVAC Budget
Project: Gulshan-01 Unimart
United Group
Date: 21-Jun-2022
6 Storey Building with Basement
Total Floor Aree =106384.12
SL. No. Description Amount (BTD) Cost per Sft Remarks
1 Central AC Material Rate 61,745,666.19 580.40
2 Installation Rate 12,890,685.90 121.17
Total = 74,636,352.00 701.57
In Word: Taka Seventy-Four Million Six Hundred Thirty-Six Thousand Three Hundred Fifty-Two Only

Prepared by Checked by Verified by Approved by

Tentative BOQ HVAC System

BOQ FOR SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF HVAC SYSTEM.

PROJECT NAME : UNIMART LTD.
PROJECT ADDRESS : UNITED BUILDING GULSHAN-1,DHAKA. DATE : 14.02.2022

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

1.0 CHILLER SYSTEM :

1.1 Magnetic Bearing Chiller with Automatic Tube Cleaning

Supply, installation, testing and commissioning as shown on the plans a factory

assembled, charged, and run-tested water-cooled packaged centrifugal chiller.
Chillers shall have at least three oil-free, magnetic bearing, (no exceptions).
Each compressor shall have an integrated variable- frequency drive operating in
concert with inlet guide vanes for optimized full and part load efficiency. On
two-compressor units, the evaporator and condenser refrigerant sides and the
expansion valve shall be common and the chiller shall be capable of running on
one compressor with the other compressor or any of its auxiliaries inoperable or
removed. The chiller shall be capable of unloading capacity to 10% of full load
without surge. performance shall be minimum 0.55 KW/TR according to AHRI
condition at full load. The unit shall be rated in accordance with AHRI Standard
550/590. All equipment 's shall be installed as per instruction by the Engineer
and Consultant.

Automatic tube cleaning system features specially developed sponge balls or

brash which are injected into the chiller condensing water flow to provide
continuous tube cleaning while the chiller is in operation. All valves, Pipes,
separator, filter, sensor, electronic actuator, Controller, timer etc. are included
with the chiller offer.

It includes Chiller Manager for sequencing of Chillers and Pumps to maintain

equal run time. Also for automatic start of Standby unit in the event of duty unit
failure.
The items shall include with complete all necessary accessories.
Chilled water in 12oC and chilled water outlet 7oC
a.Cooling capacity: 350 TR 2 Nos 7,108,051.0 7,108,051.0 0
Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -
0
Automatic Tube Cleaning Sytem (ATCS) 2 Nos - 0
Spare Parts 1 Nos - 0
Chiller Manager 2 Nos - 0
-
2.0 WATER CIRCULATION PUMP : -

Supply, installation, testing & commissioning of Horizontal suction, discharge,

horizontal split case Centrifugal pump shall be complete with all necessary
accessories, base plate, coupled motor, mechanical seal, safety cover, motor
starter, electrical control panel etc. The pump shall be minimum 70% efficient. -
Motor shall be heavy-duty type suitable to operate at 40 °C ambient
temperatures. Impeller speed shall not be more than 1,500 rpm. Power supply
shall be 400V/ 3 phase/ 50 Hz.

The motor for only secondary Chilled Water Pumps shall be suitable for use
with Variable Frequency Drive (Only for secondary pump). The motor shall be
-
screen protected drip proof (SPDP) and TEFC type. The efficiency class of
motors shall be IE 4 (Premium Efficiency) class as per IEC 60034-30 (2008).

Brand: Grundfos, Lowara, Wilo, KSB, Pentax, Armstrong, culpeda. -

-
2.1 Primary Pump : -
a.Chilled water primary pump, 850 USGPM against 20m head. 3 Nos. 925,550.0 2,776,650.0 0
- 0
2.2 Secondary Pump : - 0
a.Chilled water secondary pump, 850 USGPM against 30 m head.(Each pump
shall be VFD driven ).Pump should run at 30 Hz with maintaining 25m head 3 Nos. 994,750.0 2,984,250.0
with lower flow. 0
- 0
2.3 Condenser Pump: - 0
a.Condenser pump,1200 USGPM against 25 m head. 3 Nos. 1,159,100.0 3,477,300.0 0
-
3.0 COOLING TOWER : -
Supply, installation, testing & commissioning of cooling tower complete with
all necessary accessories and fittings, Fixing for commissioning of the
equipment including all electrical & Civil works as follows technical -
specification, drawing and time to time site instruction from Consultant and the
engineer.

Cooling tower shall be Induced draft counter flow type. It shall be complete with
make-up water valve, Float assembly, access door, Motor, Fan, Eliminators,
steel support, HDG ladder etc. Cooling Tower details along with accessories -
shall comply accordance with CTI/JCI Certification Standard STD-201 and
specification, the energy efficiency requirements of ASHRAE Standard 90.1.

Condenser water in 37oC- outlet 32oC -

Wet bulb temperature 29°C -
Approach: 3°C -
-
3.1 Capacity : 500 TR 2 Nos 2,000,000.0 4,000,000.0 0
Brand: Carrier, Trane, Kuken, BAC, Nihon Spindle - 0
- 0
4.0 Central Monitoring System : 1 Lot - 0

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 5

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

Supply, installation, testing & commissioning of Central Monitoring System

with all necessary accessories and fittings, Fixing for commissioning of the
equipment including all electrical & Civil works as follows technical
specification, drawing and time to time site instruction from Consultant / Owner.
-
Contractor should give details item quantity, unit rate , total rate as separate
pages. Control and monitoring both point should consider for chiller, pump,
FCU,AHU,HAHU,Chilled water flow, temperature and pressure, water tank
level, electrical incoming status, maintain critical load.

Chiller Plant manager shall be provided independently controlled of the plant

room equipment's for example- chiller, pumps, CT etc. It should have open
protocol to integrate with BMS system. As per I/O schedule which covered the -
chiller plant manager, those points field devices not need to reconsider again for
the central BMS due to high level integration will be done by central BMS.

Brand: Schneider, Siemens, Delta Control, Trane, Johnson Controls,

-
Honeywell, Tac.
-
5.0 AIR HANDLING UNITS : -
5.1 AIR HANDLING UNITS ( Fresh Air) : -

Supply, installation, testing and commissioning of Horizontal type

vertical/horizontal discharge draw through Air Handling Unit complete with EC
plug fan(With speed control) fan section, cooling coil section, drain pan, air
filter, spring mounted fan isolators, mixing box, temperature sensor, motorized
-
valve, controller etc. Air Handling Unit shall be modular type factory painted
and shall be weather proof. To recover heat from exhaust air, separate
(Heat Recovery Wheel / Ventilator ) should use as per specification. All
equipment 's shall be installed as per instruction by the Engineer and Consultant.

All AHU shall be VFD driven -

It shall be controlled by PICV valve -
Inner Panel: Min 22 SWG Plain Galvanized Steel sheet -
Outer Panel: Min 22 SWG Pre-plasticized Galvanized Steel sheet -
Spring Mounted vibrating Isolators for fans -
Sloped insulated SS drain pan, -
Coil face velocity : Max 2.5 m/s -
Insulation material: PU min 50 mm thick, Min density 40 kg/m3 -
All AHU should contain both G4 washable and F7 type filter -
All motor of AHU shall be of IE4 type( Super premium efficiency) with speed
-
control option
The items shall include with complete all necessary accessories. -
Chilled water enters the coil at 7°C and leaves at 12°C -
Available ESP for air distribution (Duct run + Grille)
-
(Pressure loss in coil and filter and other sections in AHU shall be added.)
All AHU specification shall be maintained as above unless otherwise item wise
-
mentioned
AHU Capacity 8000 CFM(ESP 150 Pa)
4 Nos 1,069,832.00 4,279,328.0
on coil DBT 37°C/RH 55 % & leaving air 18°C/ 70 % after heater. 0
Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -
-
6.0 Chilled Water System FCU with Drain Water Pump: -

Supply, installation, testing & commissioning of low height and low noise
Indoor Unit with all necessary accessories and fittings, Fixing for
commissioning of the equipment including return filter , electrical terminal box -
and all other electrical & Civil works as follows technical specification, drawing
and time to time site instruction from Consultant / Owner.

Unit shall be tested and certified in accordance with AHRI (Air-Conditioning,

-
Heating, and Refrigeration Institute) Standard 440
Each coil shall be factory tested for leakage at 300 psig air pressure with coil
-
submerged in water
Insulation and adhesive shall meet NFPA (National Fire Protection Association)
-
90A requirements for flame spread and smoke generation
Selected unit shall maintain Noise Criteria not more than 42dB and low height
-
units
Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -

-
6.1 Fan Coil Unit (Ducted type)with Drain Water Pump : -
Required Cooling Capacity 2.5 TR, ESP 50 Pa (Height less than 240mm) 90 Nos. 26,296.00 2,366,640.0 0
Required Cooling Capacity 3.0 TR, ESP 50 Pa (Height less than 240mm) 4 Nos. 26,296.00 105,184.0 0
Required Cooling Capacity 4.0 TR, ESP 50 Pa (Height less than 240mm) 3 Nos. 32,870.00 98,610.0 0
Required Cooling Capacity 5.0 TR, ESP 50 Pa (Height less than 300mm) 7 Nos. 34,600.00 242,200.0 0
Required Cooling Capacity 5.5 TR, ESP 50 Pa (Height less than 300mm) 21 Nos. 34,600.00 726,600.0 0
Required Cooling Capacity 6.0 TR, ESP 50 Pa (Height less than 300mm) 10 Nos. 34,600.00 346,000.0 0
-
6.2 Fan Coil Unit (Cassette type) : -
Required Cooling Capacity 1.5 TR 5 Nos. 17,300.00 86,500.0 0
Required Cooling Capacity 3.0 TR 4 Nos. 22,490.00 89,960.0 0
- 0
6.3 Fan Coil Unit (Wall Type) : - 0
Required Cooling Capacity 1.5 TR 2 Nos. 17,992.00 35,984.0 0
- 0
6.4 Pre Cooled Unit(Slim Type, Low height & Low Noise,E.S.P 80 Pa) - 0
600 CFM(4TR) 3 Nos. 40,000.00 120,000.0 0

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 6

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

-
6.4 Split Type (Wall Mounted Unite): -

Supply, installation, testing & commissioning of split type Air-cooler

comprising condensing and evaporating units having following cooling
capacity based on indoor temperature 18ºC-24ºC DB and outdoor -
temperature 35º-40ºC DB at high fan speed condition suitable for
installation & operation in tropicalized country like Bangladesh.

a. Required Cooling Capacity 1.5 TR 2 Nos. 40,000.00 86,520.0

Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -

-
7.0 Chilled Water Pipe : -
7.1 Pipe (without insulation) -
Supply & installation of Pre-insulated 40 SCH seamless pipe (ASTM A53) shall
be black steel pipe with insulation and galvanized sheet metal cladded vapor
barrier. Pipe shall be suitable to withstand a test pressure of 360 psi. Pipe shall -
be insulated with Polyurethane (PU) foam insulation. Pipe shall be of following
nominal dia.
Brand: Ricwil, Glensul , Xingbang, SEAH, Husteel or equivalent. -
20 mm dia, 65 Rm 524.80 35,135.4
25 mm dia, 740 Rm 590.40 - In stock
32 mm dia, 562 Rm 721.60 417,705.4
40 mm dia, 350 Rm 787.20 - In stock
50 mm dia, 240 Rm 918.40 - In stock
65 mm dia, 320 Rm 1,902.40 627,031.0
80 mm dia, 10 Rm 2,460.00 25,338.0
100 mm dia, 80 Rm 3,936.00 - In stock
125 mm dia, 30 Rm 4,920.00 - In stock
150 mm dia, 36 Rm 5,904.00 218,920.3
200 mm dia, 102 Rm 7,216.00 758,113.0
250 mm dia, 48 Rm 9,184.00 454,057.0
300 mm dia, 54 Rm 11,808.00 656,761.0
-
-
7.3 Chilled water Pipe insulation(Armacell) : -

Supply, installation, testing & commissioning of chilled water pipe and

Insulation works with all necessary accessories and fittings, Fixing for
commissioning of the equipment including all electrical & Civil works as -
follows technical specification, drawing and time to time site instruction from
Consultant / Owner. Pipe insulation thickness should be followed 25mm

Brand: Ricwil, Glensul , Xingbang, SEAH, Husteel or equivalent. -

20 mm dia, 65 Rm 150.00 10,042.5
25 mm dia, 740 Rm 180.00 137,196.0
32 mm dia, 562 Rm 196.00 113,456.6
40 mm dia, 350 Rm 271.00 97,695.5
50 mm dia, 240 Rm 288.00 71,193.6 armacell
65 mm dia, 320 Rm 335.00 110,416.0
80 mm dia, 10 Rm 398.00 4,099.4
100 mm dia, 80 Rm 683.00 56,279.2
125 mm dia, 30 Rm 164.00 5,067.6
150 mm dia, 36 Rm 226.00 8,380.1
200 mm dia, 102 Rm 293.00 30,782.6
250 mm dia, 48 Rm 360.00 17,798.4
300 mm dia, 54 Rm 428.00 23,805.4
-
-
-
8.0 Room Thermostat for Room FCU/AHU(IP Based): 151 Set 8,477.00 1,280,027.0 0
Supply, installation, testing & commissioning of The thermostat shall Control
PICV valve, 3 speed fan switch, space temperature indication, space temperature
set point adjustment, as Wired Controller With some IR Remote, etc.It should -
have IP provition to connect central BMS system.

-
9.0 Drain Pipe with Insulation: -

Supply, installation, testing & commissioning of Drain pipe and Insulation

works with all necessary accessories and fittings, Fixing for commissioning of
the equipment including all electrical & Civil works as follows technical -
specification, drawing and time to time site instruction from Consultant / Owner.
Pipe Pressure test should done as per Ashrae Standard.

Insulation material shall be closed Cell Cross Linked Polyethylene

(XLPE)/Nitrile Rubber Foam in the form of pre-formed pipe sections with
aluminum foil facing and complete in all respects as per specifications and
-
drawings on chilled water piping of the following sizes. The insulation material
should be of density 24±2 Kg/m³ & thermal Conductivity not exceeding 0.035
W/m³K at an average Temperature of 23°C. Insulation thickness= 25 mm
During installation contractor should consider existing services and should
-
install without damage of any services
Pipe Brand: N-Poly/RFL -
Country of Manufacture: Bangladesh -
Insulation Brand: Supreme, Superlon, Armacell or equivalent -
-

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 7

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

50mm 390 Rm 120.00 48,204.0

32mm 120 Rm 100.00 12,360.0
25 mm 260 Rm 80.00 21,424.0
20 mm 240 Rm 60.00 14,832.0
-
10.0 VALVE ACCESSORIES : -
-
10.1 Valves :(Ball/Butterfly) : -

Supply, installation, testing & commissioning of Ball / Butter fly valve shall be
lever-operated type, anti corrosive cast iron body. All should be comply with
-
specification Valve upto 80mm dia shall be welded socket ball type complete
with companion flanges, nut-bolt, gasket etc.

Brand: Tozen, Kitz, nibco, Flowserve, KSB, Pentair -

20mm dia (Ball) 21 Nos. 435.25 9,140.3 -
25mm dia (Ball) 288 Nos. 680.41 195,957.8 -
32mm dia (Ball) 132 Nos. 995.96 131,466.7 - If not available in
local market
50mm dia (Ball) 8 Nos. 1,500.00 12,000.0 -
65mm dia (Ball) 4 Nos. 2,500.00 10,000.0 -
80mm dia (Ball) 2 Nos. 3,000.00 6,000.0 -
100mm dia (Butterfly) 26 Nos. 3,760.98 97,785.5 -
125mm dia (Butterfly) 4 Nos. 5,343.75 21,375.0 -
150mm dia (Butterfly) 2 Nos. 6,975.84 13,951.7 -
200mm dia (Butterfly) 21 Nos. 12,756.57 267,888.0 -
250mm dia (Butterfly) 0 Nos. 19,276.54 -
-
10.2 Pressure independent Control Valve(PICV) : -
Supply, installation, testing , commissioning of PICV which shall be connected
with DDC controller for FCU&AHU. When the equipment is not running valve -
shall remain close.
Brand: Tozen, Danfoss, Siemens, Belimo, Johnson Control, oventrop -
20mm dia 7 Nos. 8,477.00 59,339.0 0
25mm dia 96 Nos. 9,601.50 921,744.0 0
32mm dia 44 Nos. 12,888.50 567,094.0 0
40mm dia 0 Nos. - 0
If not available in
50mm dia 0 Nos. - 0 local market
100mm dia 4 Nos. 117,726.50 470,906.0 0
125mm dia 0 Nos. 380,773.00 - 0
200mm dia 0 Nos. 713,192.50 - 0
250mm dia 0 Nos. 724,178.00 - 0
-
10.3 Y-Strainer : -

Supply, installation, testing & commissioning of Strainer shall be bronze body,

-
screwed cover, Y‑ pattern body, Stainless steel screen and flanged end type.

Brand: Tozen, Kitz or equivalent -

-
20mm dia 7 Nos. 507.62 3,553.3 0
25mm dia 96 Nos. 718.52 68,977.9 0
32mm dia 44 Nos. 1,210.55 53,264.2 0 If not available in
40mm dia 0 Nos. 1,500.00 - 0 local market
50mm dia 0 Nos. 2,500.00 - 0
100mm dia 4 Nos. 6,360.39 25,441.6 0
200mm dia 9 Nos. 45,000.00 405,000.0 0
-
10.4 Flexible Joint : -

Supply, installation, testing & commissioning of Flexible joint shall be suitable

to absorb shock and system hammering and to reduce vibration transmission.
-
Flexible joint shall be molded neoprene or butyl and suitable to withstand a
temperature of 65°C. Flexible joint shall be spherical in shape.

Brand: Tozen, Kitz, Nibco, Toyo, Metra flex or equivalent -

20mm dia 14 Nos. 675.19 9,452.7 0
25mm dia 200 Nos. 827.23 165,446.0 0
32mm dia 88 Nos. 953.94 83,946.7 0 If not available in
50mm dia 8 Nos. 1,530.22 12,241.8 0 local market
100mm dia 8 Nos. 2,861.81 22,894.5 0
200mm dia 8 Nos. 7,337.21 58,697.7 0
250mm dia 0 Nos. 11,980.18 - 0
-
10.6 Manual Balancing Valve with (Adjustable Device) : -

Supply, installation, testing & commissioning of Manual balancing valve shall

be flanged end type suitable for measuring and controlling of water flow through -
pipe and shall be complete with test port, measuring devices.
If not available in
Brand: Tozen, Kitz or equivalent - local market
200 mm dia 4 Nos. 57,302.9 229,211.6 0
250 mm dia Nos. 96,333.3 - 0
Differential pressure meter & Adjusting kit for MBV -
-
10.7 Automatic Balancing Valve : -

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 8

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

Supply, installation, testing & commissioning of Electric operated Automatic

Balancing shall be single seated, straight through, globe body, normally close
type high lift plug, flanged end type with companion flanges and gasket. The
-
valve shall be operable on system pressure. If system pressure increased it will If not available in
open and by pass water. The valve shall be complete with modulator motor, low local market
voltage transformer, pressure sensor for water pipe, actuator, linkage etc.

250mm dia 0 Nos -

200mm dia 1 Nos 150,000.0 150,000.0 -
-
10.8 3-way Auto Modulating Valve : -

Supply, installation, testing & commissioning of Electric operated 3-way

modulating valve shall be single seated, straight through, globe body, normally
close type high lift plug, flanged end type with companion flanges and gasket.
-
The valve shall be operable on system pressure. If system pressure increased it If not available in
will open and by pass water. The valve shall be complete with modulator motor, local market
low voltage transformer, pressure sensor for water pipe, actuator, linkage etc.

200mm dia 0 Nos. 120,487.5 -

250mm dia 0 Nos. 136,552.5 -
-
Brand: Schneider, Siemens, ABB, Delta Control or equivalent -
-
10.9 2-way Motorized Valve : -

Supply, installation, testing & commissioning of Electric operated 2-way Solinoid

valve shall be single seated, straight through, globe body, normally close type high lift
plug, flanged end type with companion flanges and gasket. The valve shall be operable
on system pressure. If system pressure increased it will open and by pass water. The
-
valve shall be complete with modulator motor, low voltage transformer, pressure
sensor for water pipe, actuator, linkage etc.

200mm dia 4 Nos. - If not available in

local market
100mm dia 6 Nos. -
80mm dia 1 Nos. -
65mm dia 2 Nos. -
50mm dia 4 Nos. -
40mm dia 0 Nos. -
32mm dia 0 Nos. -
25mm dia 0 Nos. -
20mm dia 0 Nos. -
-
Brand: Schneider, Siemens, ABB, Delta Control or equivalent -
-
10.10 Flo Trex Valve -
Supply, installation, testing & commissioning of Check valves shall be re-grind
able seat, screwed cap, lift type disc (vertical line), integral seal and flanges end -
type.
Brand: Tozen, Kitz, Nibco, Flowserve, KSB, Pentair, Combi -
-
200mm dia 9 Nos. 8,757.1 78,814.1 0 If not available in
- 0 local market
10.11 Auto Vent Valve with shut off valve : - 0

Supply, installation, testing & commissioning of Automatic vent valve with ball
valve shall be free floating type having test cock, 20 mm threaded outlets to 15 Nos. 349.8 5,247.6
accept drain line and threaded inlet connection. Vent valve shall be 20-mm size.
0
Brand: Tozen, Kitz or equivalent -
-
11.0 METERING DEVICE : -

Supply, installation, testing & commissioning of metering device such as

pressure gauge, pipe thermometer, duct thermometer and flow-meter shall be at
location shown in the drawing and as per direction. Required size of bush shall -
be welded on pipe. It shall be water leak proof at a pressure of 10 Kg/cm2.
metering devices shall be installed as per recommendation of the manufacturer.

Brand: Tozen, Shield or equivalent -

-
11.1 Pressure Gauge : 60 Nos. 1,723.13 103,387.8 0
Supply, installation, testing & commissioning of Pressure Gauge for water pipe If not available in
line shall be of dial type of 100 mm dia suitable to read 0 to 10 Kg pressure. local market
-
Pressure gauge with ball valve shall be complete with pet cock, pressure
snobber, nipple etc. 0
- 0
11.2 Pipe Thermometer : 60 Nos. 2,233.00 133,980.0 0
Supply, installation, testing & commissioning of Adjustable angle, direct
reading, industrial type pipe thermometer with shut up valve shall be complete If not available in
- local market
with thermometer well, socket. Thermometer with ball shall be suitable to read
water temperature of range 0 to 50°C.
-
12.0 Ventilation Fan : -

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 9

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

Supply, installation, testing & commissioning of duct type/wall mounted

Galvanized box type fan Fixed driven fan suitable to move substantial amounts
of air at low pressure with minimal energy consumption. The fan motor shall be
single/Three phase and fans shall be complete with centrifugal shutter at external
side and wire mesh guard at internal side. Fan frame shall be constructed from
galvanised steel with a stainless steel impeller. Fans ball bearings shall be sealed -
for life time. If not available in
The fan blades shall be truly reversible type SS made & shutter opening local market
mechanism shall be centrifugal link type push pull system.
The motor type shall be IE3 with IP55 protection.(Sound level shoud be
maintain less than 60db at 1m distance.)

Fan noise lavel should not be more then 35 dB -

Brand: Systemair, Kruger, Nicotra -
-
12.1 Cabinet type Fresh Air Fan(Duct Type): -
Capacity : 4000 cfm, ESP 100 Pa 0 Nos. 116,775.00 -
Capacity : 10000 cfm, ESP 150 Pa (For Basement) 4 Nos. 222,305.00 889,220.0 0
- 0
12.2 Cabinet type Exhaust Air Fan(Duct Type): - 0
Capacity : 800 cfm, ESP 100 Pa 3 Nos. 29,842.50 89,527.5 0
Capacity : 2000 cfm, ESP 100 Pa 1 Nos. 44,980.00 44,980.0 0
Capacity : 5000 cfm, ESP 100 Pa 0 Nos. 68,000.00 - 0
Capacity : 10000 cfm, ESP 150 Pa (For Basement) 4 Nos. 123,262.50 493,050.0 0
- 0
12.3 Kitchen Fresh Air Fan(Duct Type): - 0
- 0
Capacity : 4000 cfm, ESP 100 Pa 1 Nos. 60,550.00 60,550.0 0
Capacity : 2500 cfm, ESP 50 Pa 0 Nos. 38,492.50 - 0
Capacity : 2000 cfm, ESP 100 Pa 1 Nos. 44,000.00 44,000.0 0
- 0
13.4 Kitchen Exhaust Fan(Duct Type): - 0
capable of handling hot as oily air - 0
- 0
Capacity : 5000 cfm, ESP 100 Pa 1 Nos. 92,555.00 92,555.0 0
Capacity : 2500 cfm, ESP 100 Pa 0 50,000.00 - 0
- 0
13.5 Toilet Exhaust Fan(Ceiling Suspended Type): - 0
Capacity : 200 cfm, ESP 50 Pa 5 Nos. 11,245.00 56,225.0 0
Capacity : 100 cfm, ESP 50 Pa 9 Nos. 7,785.00 70,065.0 0
Capacity : 50 cfm, ESP 50 Pa 11 Nos. 7,352.50 80,877.5 0
` - 0
14.6 Exhaust Fan(Wall Type): - 0
Capacity : 500 cfm, ESP 50 Pa 29 Nos. 7,785.00 225,765.0 0 If available in local
market
Capacity : 100 cfm, ESP 50 Pa 2 Nos. 6,500.00 13,000.0 0
14.7 Staire Pressured System - 0
Inchuding pressure sensor and fire signal receive controller - 0
6000 CFM, Fresh Air Fan with VFD Drive & Pressure sensor with controllar ,
1 Nos. 77,850.00 77,850.0
ESP 200 Pa.( for.Stair case) 0
12000 CFM, Fresh Air Fan , ESP 150 Pa.( for.Stair case) 1 Nos. 105,530.00 105,530.0 0
- 0
14.6 Jet Fan with silencer: - 0

Supply & Installation of ceiling mounted Impulse Two speed type jet fans are
suitable for ventilation of larger buildings where space limitaiton is substantial
and duct work should be avoided. By adding momentum to the air the jet vent
thrusts air to the desired point and generates comfort velocity. Each fan shall be
complete with dual speed motor, casing made of sheet steel duly MS Powder
coated, die cast aluminium impeller, mounting arrangements, Powder coated
-
mild steel outlet deflector and zinc plated inlet guard with silencer. Fans shall be If not available in
capable of delivering 2800 cfm air against a minimum thrust of 86N at full load local market
and 2800 cfm air against a minimum thrust of 22N to successfully throw the air
in the entire region. Fan frame shall be constructed from galvanised steel with a
alluminium alloy impeller. Fans ball bearings shall be sealed for lifetime & Low
Noise type(Sound level shoud be maintain less than 60db at 1m distance)

0
Capacity : 2800 cfm 3 Nos. 92,555.00 277,665.0 0
Capacity : 2800 cfm (For Basement) 4 Nos. 92,555.00 370,220.0 0
-
15.0 Air Terminal : -
Supply & installation of Air terminal with necessary frame,fitting,gasket and
-
adjustment items.

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 10

If available in local
market &Selected
Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

-
15.1 Supply Air Grille -

Supply & installation of Aluminum Louvered ceiling Diffuser with back damper
and plenum shall be selected to confirm face for adjustable horizontal discharge
airflow. At typical flow rates, isothermal throws of 6 to 16 feet with 37 NC
level . The diffuser shall have an easily removable core with fixed blades in 1, 2,
3, or 4-way configurations. The manufacturer shall provide published (printed or
electronic) performance data for the diffuser. The diffuser shall be tested in
-
accordance to the data standards at the time of product introduction or
ANSI/ASHRAE Standard 70.
Linear slot diffuser, plenum shall be attached to the linear by means of spring
clips to allow for plenum removal without use of special tools.Selection chart
should be provided based on required CFM which are indicated in drawing to
get approval.

Brand: Systemair, TROX, Titus, Price, Ruskin, Halton or equivalent - If available in local
market &Selected
-
by Architect
Neck Size: 4975 x 200 mm 3 Nos. 8,304.00 26,942.3
Neck Size: 400 x 400 mm 20 Nos. 1,332.10 28,813.3
Neck Size: 450 x 450 mm 91 Nos. 1,660.80 163,450.1
Neck Size: 1500 x 100 mm 0 Nos. 1,427.25 -
Neck Size: 1525 x 75 mm 35 Nos. 1,159.10 43,874.8
Neck Size: 1375 x 75 mm 4 Nos. 2,032.75 8,793.7
Neck Size: 1200 x 100 mm 232 Nos. 1,081.25 271,294.3
Neck Size: 1675 x 75 mm 4 Nos. 1,297.50 5,613.0
Neck Size: 900 x 200 mm 0 Nos. 1,531.05 -
Neck Size: 900 x 100 mm 22 Nos. 899.60 21,404.2
Neck Size: 600 x 100 mm 75 Nos. 726.60 58,936.3
Neck Size : Dia 300 mm(Round Diffuser) 58 Nos. 1,055.30 66,195.8
Neck Size: 300 x 300 mm 11 Nos. 1,591.60 18,934.5
Neck Size: 1200 x 150 mm 0 Nos. 1,584.00 -
Neck Size: m² 0 m² -
15.2 Fresh Air Louver With insect screen and Washable Filter: -
Neck Size: 400 x 200 mm 3 Nos. 808.78 2,624.1
Neck Size: 600 x 350 mm 1 Nos. 1,848.00 1,998.6
Neck Size: 1200 x 450 mm 1 Nos. 4,752.00 5,139.3 If available in local
market &Selected
Neck Size: 120 x 250 mm (For Basement) 4 Nos. 264.00 1,142.1 by Architect
-
-
15.3 Exhaust Air Louver With insect screen: -
Supply, installation, testing & commissioning of extruded aluminium Exhaust
Air Louver With insect screen terminal with mat finishing of approved colour on
the air distribution duct line /coller / ceiling etc. including supply and -
installation of necessary fixing screw, gasket , necessary insulation( if required)
etc.
If available in local
Neck Size: 450 x 250 mm 3 Nos. 990.00 3,212.1 market &Selected
Neck Size: 600 x 450 mm 1 Nos. 2,768.00 2,993.6 by Architect
Neck Size: 1200 x 600 mm 1 Nos. 6,336.00 6,852.4
Neck Size: 600 x 250 mm 0 Nos. 1,320.00 -
Neck Size: 120 x 250 mm (For Basement) 4 Nos. 264.00 1,142.1
Neck Size: m² 20 m² -
-
15.4 Return Air Liner Bar Grille : -
Neck Size: 350 x 350 mm 4 Nos. 631.45 2,731.7
Neck Size: 300 x 300 mm 0 Nos. 484.40 -
Neck Size: 1200 x 500 mm 21 Nos. 986.10 22,395.8 If available in local
Neck Size: m² 0 m² - market &Selected
- by Architect
15.5 Service Door With Return Grill : -
Neck Size: 600 x 600 mm 93 Nos. 2,768.00 278,404.1
-
16.0 DUCT WORK: -

Supply, fabrication and installation of galvanized sheet steel duct work complete
with bends, Tees, reducers, branch takeoffs, air chamber etc. as per direction and
drawing. Hangers, brackets, stiffeners and isolator boxes shall be fabricated with
M.S. angle/F.I. bar or rod as per drawing and direction and shall be galvanized.
Duct shall be constructed with best-bloomed galvanized sheet steel. Before
- For center fresh air
installation of duct, inside and outside shall be cleaned from any dust. Between
flanges, for flanged end duct, approved type of gasket shall be used. Approved duct
type of sealing compound shall be used to make the duct work leak-proof. Duct
shall be hanged or supported at an interval of not more than 1.8 meter.

20 BWG 200 sqm 900.00 48,667.5

16.1 PIR PANEL -

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 11

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

PIR Foam Pre-insulated Duct

Panel
Size:3950*1200*20mm,
Foam Density: 50kg/m3,
Both sides faced with 80 -
micron thickness embossed
AL foil,
Packing: 10sheets/carton,
1374 sheets in total.

6512 sqm 653.94 4,258,457.3 0

PVC Invisible Flange Joint (in 4 mtr length) 6600 mtr 42.39 279,741.00 -
PVC Tee Cinnector Flange Joint 560 mtr 44.12 24,704.40 -
PVC H Bayonet 3600 mtr 23.34 84,006.00 -
Zinc-coated Steel Angle Bracket 10000 pc 7.79 77,850.00 -
PVC Covering Angle 5000 pc 7.79 38,950.00 -
PVC Chair section Bar 240 mtr 47.58 11,418.00 -
PVC U section Bar 560 mtr 44.98 25,188.80 -
PVC F section Bar 240 mtr 47.58 11,418.00 -
Aluminium Adhesive Tape 288 roll 274.21 78,971.04 -
Zinc Coated Steel shaped Disk 200 pc 18.17 3,633.00 -
Aluminium Reinforcement Section Bar 400 mtr 70.07 28,026.00 -
Zinc Coated Steel Hanger 500 pc 39.79 19,895.00 -
-
16.1 Flexible Ducting : -
Supply, installation, testing & commissioning of UL Listed CIRCULAR pre-
insulated fire retardant spiral flexible duct made of aluminium foil insulated -
using fibre glass - 14 Kg per cum density
Brand: MEGA/ equivalent -
-
Ø300mm 300 Rm 432.50 129,750.0 0
Ø250mm 200 Rm 380.60 76,120.0 0
-
-
19.0 VOLUME CONTROL DAMPER : -
Supply & installation of volume control damper constructed with 18 BWG sheet
steel painted with 2 coats of synthetic black paint, adjustable locking
50 sqm 9,300.00 502,897.5
arrangement from outside of duct and suitable to mount on flanged end duct as
per drawings and direction of the Engineer (local made) . if available in local
market
Brand: Halton, TROX, Price, Ruskin, System Air or equivalent -
-
20.0 Non Return Damper : -

Supply and installation of opposed blade type Non return damper constructed
with 18 BWG sheet steel painted with two coats of synthetic black paint. The
damper shall have adjustable locking arrangement with worm gear operable
50 sqm 9,300.00 502,897.5
from outside duct work and shall be flanged end type suitable to mount on
flanged end duct work. Non return dampers shall be as per layout drawings and
direction.

Brand: Halton, TROX, Price, Ruskin, System Air or equivalent -

-
21.0 Electromagnetic Flow Meter: -

Supply of Electromagnetic flow meter for constant measuring flow of the piping
system shall be constructed from high grade steel / alloy steel with flange end,
leak proof gasket ,suitable for working pressure up to 300 psig and complete -
with SENSORPROM unit for automatically uploads calibration values and
setting ete compatible operation of BMS etc.

Brand: Siemens, ABB, Johnson Controls or equivalent -

-
50mm dia 0 Nos. -
100mm dia 0 Nos. -
0 if not available in
150mm dia Nos. -
local market
200mm dia 1 Nos. - 0
250mm dia 0 Nos. -
-
22.0 EXPANSION TANK (Close Type) : 1 Job 328,700.0 328,700.0 0

Supply, installation, testing & commissioning of expansion tank constructed

with 18 BWG galvanized sheet steel having connection for expansion pipe, feed
water line and over flow line. The tank shall be installed on steel framing at a if not available in
-
height of at least 1.5 meter from top level of chilled water pipe. The tank shall be local market
insulated with 25 mm thick insulation and plastered with 25 mm thick mortar
over chicken wire mesh. Tank size shall be 750 lit.

Brand: Reflex or equivalent -

-
23.0 WATER SOFTNER PLANT : Set. 908,250.0 908,250.0 -

Supply, Installation, Testing & Commissioning of Vertical pressure type Water

Softener made out of MSEP / FRP composite vessel with top and bottom
openings, self-supporting legs, suitable distribution and collection system, initial -
charge of Resin, pressure gauges, sampling cock, air vent, frontal MS piping,
diaphragm valves for inlet, backwash outlet etc. complete

The price shall be included all chemical items for one year. -
The design parameter shall be fixed based on the water quality and test report. -

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 12

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

Capacity :50 gpm -

Operating pressure - 3.5 + 0.5 Kg/cm2 -
Testing pressure - 10 Kg/cm2 -
Input water hardness - 100 ppm or design as per parameter -
Outlet water hardness - Not exceeding 20 ppm or design as per parameter -
Regeneration Cycle - 24 hours -
Brand: -
Country of Manufacture: -
Country of Origin: -
-
24.0 Dirt and Air separator : 1 Nos. 2,175,475.0 2,175,475.0 0
Supply, installation, testing and commissioning of dirt and air separator with
proper sized shutoff valve at both end in a combination of air & sediment
separator that utilizes a coalescing medium to remove impurities from HVAC
systems. It features a stainless steel coalescing medium with 58% open area,
-
removable end cover for coalescing medium
access, and connections for an air vent, blow down valve, and skim valve. The
product is designed, constructed, inspected and
stamped per ASME Section VIII, Division 1

Construction material -
Shell: Carbon Steel
-
Coalescing Medium: Stainless Steel
Maximum working pressure 150 Psig -
Flow rate= 1680 US GPM -
-
25.0 MAKE-UP WATER TANK WITH FLOAT VALVE: 1 Set. 55,000.0 59,482.5

Supply, installation, testing & commissioning of high quality PVC/Plastic make-

up water Tank along with adequately rated make-up water pump, for make-up of
-
water for cooling towers. The tank shall have connection for, feed water line,
overflow line, drain line etc. Mackeup water tank capacity 8000 Lit

Brand:Carno or equivalent -
-
26.0 Chemical Dosing System: 1 Set. 198,950.0 198,950.0 0
Supply of include with auto feed type suitable to handle of chilled water to
control corrosion, scale and biological effect and shall be complete with dosing
- if not available in
pumps, sensor, control valves, PVC tubes and tube fittings for chemical feed, pH
analyzer and indicator etc. complete. local market

Brand: Microdos/ Nalco/ X-Pot or equivalent -

-
27.0 Side Stream Filter System: 1 Set. -

Supply, installation, testing & commissioning of side stream filter system

include with Pump and accessories to ensure continuously filter a portion of
cooling water to remove debris and particles. Side stream filtration requires a
minimum supply pressure to account for the inherent differential pressure drop
-
across the filter typically ranges from 20 to 30 psi. All side stream filters have a
maximum working pressure; sand filters have a threshold of 80 psi. Systems
require cleaning of filters or holding chambers to remove debris and particles
that are trapped in filters.

System handling capacity is 210 gpm and residual head- 20 meter after filtration. -

Capacity: 210 gpm; Residual Head after filtration= 20 m -

-
28.0 Performance Test / Check at Factory (or PSI) : -

Performance Test / Check at Factory (or PSI) : Before shipment the main
product vendor/contractor should arrange the Performance test arrangement for
the main product at Manufacturer factory lab for Consultant and Client 1 Job -
person.There should have testing arrangement as per standard procedure at
factory test facility area .chiller test should perform as per AHRI condition.

-
29.0 Cladding of Pipe: 200 sqm - #REF!

Supply, installation, testing & commissioning of Jacketing shall be done with 26

-
SWG Aluminum sheet. Weather proof sealant to be used at all joining places.

Brand: Zinc Coat or equivalent -

-
30.0 Testing Port : -
Supply, installation, testing & commissioning of In supply and return pipe
contractor should install a testing port having threaded end cap ,ball valve and
160 Nos. -
capable to insert thermometer/ temperature gauge when required for pressure
gauge and temperature gauge
-
31.0 Intumescent Sealant : -

Supply, installation, testing and commissioning of fire barrier sealant which

shall be a one component, ready-to-use, gun-grade, latex-ased,intumescent fire
stop sealant capable of expanding a minimum of three times its dried volume
when exposed to temperatures above 1000°F (538°C). The material shall be
thixotropic and shall be applicable to overhead, vertical and horizontal fire stops.
The sealant shall be listed by independent test agencies such as UL, Intertie or
100 L -
FM. Fire Barrier Sealant shall be tested to and pass the criteria of ASTM E 814
(UL 1479) Standard Test Method for Fire Tests of Penetration Fire stop
Systems, ASTM E 1966 (UL 2079) Standard Test Method for Fire Resistive
Joint Systems and CAN/ULC S115 Standard Method of Fire Tests of Fire stop
Systems.
N.B: During Shop drawing this quantity may subject to change

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 13

Tentative BOQ HVAC System

AS PER
UNIT RATE Imported TOTAL Local TOTAL
SL. NO. SHORT DESCRIPTION DWG. UNIT REMARKS
(BDT) AMOUNT (BDT) AMOUNT (BDT)
QTY

Brand: 3M, Dupont or equivalent -

-
32.0 Testing, Commissioning and Balancing and Drawings: 1 Job -
After proper installation and certification the system shall be tested,
commissioned and balanced as per direction and recommendation by the
-
Manufacturer as well as HVAC Designer. Contractor shall do (but not limited
to) following works under this clause.
a. Prepare and submit shop drawing , As built drawing, Commissioning protocol
-
and get approval from Consultant.
b. Carry out duct inspection -
c. Carry out pipe pressure testing -
d. Carry our Electrical Cabling testing -
e. Testing of condensate water drainage slope with water -
f. Safety protection and cut-outs shall be tested individually -
g. Commissioning of Automatic Control system -
Balancing and Adjusting of HVAC system -

Balancing and adjusting of the system should be in a process to optimize the

HVAC system to ensure that air conditioning outputs(desired air flow, chilled
-
water flow, desired air out temperature from diffuser etc.) are consistent, and
temperatures are attained in all rooms as per design and drawing

-
33.0 Chilled Water Balancing: 1 Job -
Chilled water balancing shall apply a disciplined procedure of adjustment to
water flow rates throughout the chilled water system to meet the particular
requirement of the design drawing. Following but not limited to should be -
followed during balancing

34.0 Air Balancing: 1 Job -

Purpose of air balancing is to define the step by step method to implement the
correct practice for the air balancing to ensure the job execution complies with
the project requirements and serve the intended function to the satisfactory level -
( as per design and drawing). Ensure air flow capacity and temperature as per
design and drawing

All testing and commissioning works must be documented room wise/zone wise
in approved formats. All of these document's must be jointly witnessed and -
signed by the Client and Contractor's authorized Engineer.

-
35.0 Engineering Team : Start from Mobilization 1 Job -
Senior engineer with design knowledge to prepare modification , reporting and
-
perform meeting( Should be conversant in English)
Site Supervisor Engineer, construction management team , drafting and drawing
-
preparation team.

Team also be capable of prepare shop drawing, and as built drawing, time to
-
time approval from consultant or project authorized person from client

-
36.0 DOCUMENTATION : 1 Job -

Detail layout and fabrication drawing shall be prepared as per guide line layout
drawing and shall be submitted for approval. Modification drawing shall be
prepared as per site condition. Layout drawings shall be coordinated with other
services. Required section and detail shall be prepared. Construction work shall
-
be done as per approved working drawings. Compilation of all the document
such as built drawing, testing, commissioning & balancing report, operation and
maintenance manuals etc. shall be done as per direction. Drawings shall be
prepared on Auto Cad.

-
37.0 OPERATION AND MAINTENANCE: Year -

After completion of warranty period, operation and maintenance will be started

as per tender instruction. A full time operator and maintenance engineer (B.Sc..
Mechanical) shall be deputed at site during operation and maintenance work.
During operation and maintenance if any defect in installation work is detected, -
shall be rectified by the contractor at no extra cost. Logbook to record
performance of the system shall be maintained as follows technical
specification, drawing and time to time site instruction from Consultant / Owner.

Sub Total 46,268,072.91 6,219,446.8

CNF ,Insurace,Tax,Transportation etc 11% 5,089,488.0
Freight Charge 3,702,200.0
Vat with local 7.5% 466,458.507
TOTAL Amount In BDT 55059760.9 6,685,905.3
TOTAL Amount In BDT(Local Plus foreign) 61,745,666.2
NOTE:
a. Installation means installation, testing & commissioning of The respective item as per drawing & specifications complete with
all necessary accessories and fittings for commissioning of the equipment including all electrical & Civil works. If any item
description conflict with BOQ and Specification then consider best selection for that item or follow the consultant instruction.
Any TAX,VAT or others should be included in this offer.
b. Contactor bill should be adjusted as per actual site quantity of install item.
c. Materials should be supplied at actual as per site requirements.
d. Prepare shop drawing as per site requirement and manufacturer recommendation and get approval from consultant prior
opening the LC or start the work.

Prepared By : Electro-Mechanical Control Services (eMcS) Item of Schedule 14

BOQ FOR SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF HVAC SYSTEM

Project Name : UNIMART LTD

Project Address : UNITED BUILDING GULSHAN-1,DHAKA Date : 16.01.2022

SL. Install UNIT TOTAL AMOUNT

SHORT DESCRIPTION QTY UNIT REMARKS
NO. RATE (BDT) (BDT)

1.0 CHILLER SYSTEM :

1.1 Magnetic Bearing Chiller with Automatic Tube Cleaning
Supply, installation, testing and commissioning as shown on the plans a factory
assembled, charged, and run-tested water-cooled packaged centrifugal chiller.
Chillers shall have at least three oil-free, magnetic bearing, (no exceptions).
Each compressor shall have an integrated variable- frequency drive operating in
concert with inlet guide vanes for optimized full and part load efficiency. On
two-compressor units, the evaporator and condenser refrigerant sides and the
expansion valve shall be common and the chiller shall be capable of running on
one compressor with the other compressor or any of its auxiliaries inoperable or
removed. The chiller shall be capable of unloading capacity to 10% of full load
without surge. performance shall be minimum 0.55 KW/TR according to AHRI
condition at full load. The unit shall be rated in accordance with AHRI Standard
550/590. All equipment 's shall be installed as per instruction by the Engineer
and Consultant.

Automatic tube cleaning system features specially developed sponge balls or

brash which are injected into the chiller condensing water flow to provide
continuous tube cleaning while the chiller is in operation. All valves, Pipes,
separator, filter, sensor, electronic actuator, Controller, timer etc. are included
with the chiller offer.

It includes Chiller Manager for sequencing of Chillers and Pumps to maintain

equal run time. Also for automatic start of Standby unit in the event of duty unit
failure.
The items shall include with complete all necessary accessories.
Chilled water in 12oC and chilled water outlet 7oC
a.Cooling capacity: 350 TR 2 Nos 40,000.0 80,000.0

Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -

-
2.0 WATER CIRCULATION PUMP : -

Supply, installation, testing & commissioning of Horizontal suction, discharge,

horizontal split case Centrifugal pump shall be complete with all necessary
accessories, base plate, coupled motor, mechanical seal, safety cover, motor
starter, electrical control panel etc. The pump shall be minimum 70% efficient. -
Motor shall be heavy-duty type suitable to operate at 40 °C ambient
temperatures. Impeller speed shall not be more than 1,500 rpm. Power supply
shall be 400V/ 3 phase/ 50 Hz.

The motor for only secondary Chilled Water Pumps shall be suitable for use
with Variable Frequency Drive (Only for secondary pump). The motor shall be
-
screen protected drip proof (SPDP) and TEFC type. The efficiency class of
motors shall be IE 4 (Premium Efficiency) class as per IEC 60034-30 (2008).

Brand: Grundfos, Lowara, Wilo, KSB, Pentax, Armstrong, culpeda. -

-
2.1 Primary Pump : -
a.Chilled water primary pump, 850 USGPM against 20m head. 3 Nos. 12,500.0 37,500.0
-
2.2 Secondary Pump : -
a.Chilled water secondary pump, 850 USGPM against 30 m head.(Each pump
shall be VFD driven ).Pump should run at 30 Hz with maintaining 28m head 3 Nos. 12,500.0 37,500.0
with lower flow.
-
2.3 Condenser Pump: -
a.Condenser pump,1260 USGPM against 25 m head. 3 Nos. 12,500.0 37,500.0
-
3.0 COOLING TOWER : -
Supply, installation, testing & commissioning of cooling tower complete with
all necessary accessories and fittings, Fixing for commissioning of the
equipment including all electrical & Civil works as follows technical -
specification, drawing and time to time site instruction from Consultant and the
engineer.

Cooling tower shall be Induced draft counter flow type. It shall be complete with
make-up water valve, Float assembly, access door, Motor, Fan, Eliminators,
steel support, HDG ladder etc. Cooling Tower details along with accessories -
shall comply accordance with CTI/JCI Certification Standard STD-201 and
specification, the energy efficiency requirements of ASHRAE Standard 90.1.

Condenser water in 37oC- outlet 32oC -

Wet bulb temperature 29°C -
Approach: 3°C -
-
3.1 Capacity : 500 TR 2 Nos 65,000.0 130,000.0
Brand: Carrier, Trane, Kuken, BAC, Nihon Spindle -
-
4.0 Central Monitoring System : 1 Lot -

Supply, installation, testing & commissioning of Central Monitoring System

with all necessary accessories and fittings, Fixing for commissioning of the
equipment including all electrical & Civil works as follows technical
specification, drawing and time to time site instruction from Consultant / Owner.
-
Contractor should give details item quantity, unit rate , total rate as separate
pages. Control and monitoring both point should consider for chiller, pump,
FCU,AHU,HAHU,Chilled water flow, temperature and pressure, water tank
level, electrical incoming status, maintain critical load.
 Chiller Plant manager shall be provided independently controlled of the plant
room equipment's for example- chiller, pumps, CT etc. It should have open
protocol to integrate with BMS system. As per I/O schedule which covered the -
chiller plant manager, those points field devices not need to reconsider again for
the central BMS due to high level integration will be done by central BMS.

Brand: Schneider, Siemens, Delta Control, Trane, Johnson Controls,

-
Honeywell, Tac.
-
5.0 AIR HANDLING UNITS : -
5.1 AIR HANDLING UNITS ( Fresh Air) : -

Supply, installation, testing and commissioning of Horizontal type

vertical/horizontal discharge draw through Air Handling Unit complete with EC
plug fan(With speed control) fan section, cooling coil section, drain pan, air
filter, spring mounted fan isolators, mixing box, temperature sensor, motorized
-
valve, controller etc. Air Handling Unit shall be modular type factory painted
and shall be weather proof. To recover heat from exhaust air, separate
(Heat Recovery Wheel / Ventilator ) should use as per specification. All
equipment 's shall be installed as per instruction by the Engineer and Consultant.

All AHU shall be VFD driven -

It shall be controlled by PICV valve -
Inner Panel: Min 22 SWG Plain Galvanized Steel sheet -
Outer Panel: Min 22 SWG Pre-plasticized Galvanized Steel sheet -
Spring Mounted vibrating Isolators for fans -
Sloped insulated SS drain pan, -
Coil face velocity : Max 2.5 m/s -
Insulation material: PU min 50 mm thick, Min density 40 kg/m3 -
All AHU should contain both G4 washable and F7 type filter -
All motor of AHU shall be of IE4 type( Super premium efficiency) with speed
-
control option
The items shall include with complete all necessary accessories. -
Chilled water enters the coil at 8°C and leaves at 13°C -
Available ESP for air distribution (Duct run + Grille)
-
(Pressure loss in coil and filter and other sections in AHU shall be added.)
All AHU specification shall be maintained as above unless otherwise item wise
-
mentioned
Chilled water enters the coil at 8°C and leaves at 13°C -
a) Required Cooling Capacity 8000 CFM(ESP 150 Pa)
4 Nos 18,000.00 72,000.0
on coil DBT 37°C/RH 60 % & leaving air condition 18°C/ 70 %

Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -

-
6.0 Chilled Water System FCU with Drain Water Pump: -

Supply, installation, testing & commissioning of low height and low noise
Indoor Unit with all necessary accessories and fittings, Fixing for
commissioning of the equipment including return filter , electrical terminal box -
and all other electrical & Civil works as follows technical specification, drawing
and time to time site instruction from Consultant / Owner.

Unit shall be tested and certified in accordance with AHRI (Air-Conditioning,

-
Heating, and Refrigeration Institute) Standard 440
Each coil shall be factory tested for leakage at 300 psig air pressure with coil
-
submerged in water
Insulation and adhesive shall meet NFPA (National Fire Protection Association)
-
90A requirements for flame spread and smoke generation

Selected unit shall maintain Noise Criteria not more than 42 and low height units -

Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -

-
6.1 Fan Coil Unit (Ducted type)with Drain Water Pump : -
Required Cooling Capacity 2.5 TR, ESP 50 Pa (Height less than 240mm) 88 Nos. 2,000.00 176,000.0
Required Cooling Capacity 3.0 TR, ESP 50 Pa (Height less than 240mm) 4 Nos. 2,500.00 10,000.0
Required Cooling Capacity 4.0 TR, ESP 50 Pa (Height less than 240mm) 3 Nos. 3,000.00 9,000.0
Required Cooling Capacity 5.0 TR, ESP 50 Pa (Height less than 300mm) 7 Nos. 3,500.00 24,500.0
Required Cooling Capacity 5.5 TR, ESP 50 Pa (Height less than 300mm) 21 Nos. 4,000.00 84,000.0
Required Cooling Capacity 6.0 TR, ESP 50 Pa (Height less than 300mm) 10 Nos. 5,000.00 50,000.0
-
6.2 Fan Coil Unit (Cassette type) : -
Required Cooling Capacity 1.5 TR 6 Nos. 1,500.00 9,000.0
Required Cooling Capacity 3.0 TR 4 Nos. 2,500.00 10,000.0
-
6.3 Fan Coil Unit (Wall Type) : -
Required Cooling Capacity 1.5 TR 2 Nos. 1,500.00 3,000.0
-
6.4 Pre Cooled Unit(Slim Type, Low height & Low Noise,E.S.P 80 Pa) -
600 CFM(4TR) 3 Nos. 1,200.00 3,600.0
-
6.4 Split Type (Wall Mounted Unite): -
Supply, installation, testing & commissioning of split type Air-cooler
comprising condensing and evaporating units having following cooling
capacity based on indoor temperature 18ºC-24ºC DB and outdoor -
temperature 35º-40ºC DB at high fan speed condition suitable for
installation & operation in tropicalized country like Bangladesh.

a. Required Cooling Capacity 1.5 TR 2 Nos. -

Brand:Daikin,Trane, Climaveneta, Smardt, Dunham-Bush, Carrier, York. -

-
7.0 Chilled Water Pipe : -
7.1 Pre-Insulated Pipe : -
 Supply & installation of Pre-insulated 40 SCH seamless pipe (ASTM A53) shall
be black steel pipe with insulation and galvanized sheet metal cladded vapor
barrier. Pipe shall be suitable to withstand a test pressure of 360 psi. Pipe shall -
be insulated with Polyurethane (PU) foam insulation. Pipe shall be of following
nominal dia.
Brand: Ricwil, Glensul , Xingbang, SEAH, Husteel or equivalent. -
-
20 mm dia, 65 Rm 170.00 11,050.0
25 mm dia, 740 Rm 200.00 148,000.0
32 mm dia, 562 Rm 250.00 140,500.0
40 mm dia, 350 Rm 265.00 92,750.0
50 mm dia, 240 Rm 285.00 68,400.0
65 mm dia, 320 Rm 350.00 112,000.0
80 mm dia, 10 Rm 380.00 3,800.0
100 mm dia, 80 Rm 850.00 68,000.0
125 mm dia, 30 Rm 1,050.00 31,500.0
150 mm dia, 36 Rm 1,200.00 43,200.0
200 mm dia, 102 Rm 1,700.00 173,400.0
250 mm dia, 48 Rm 1,900.00 91,200.0
300 mm dia, 54 Rm 2,200.00 118,800.0
-
-
7.3 Chilled water Pipe insulation(XLPE) : -

Supply, installation, testing & commissioning of chilled water pipe and

Insulation works with all necessary accessories and fittings, Fixing for
commissioning of the equipment including all electrical & Civil works as
-
follows technical specification, drawing and time to time site instruction from
Consultant / Owner. Pipe insulation thickness should be followed as per
specification.
Insulation Brand: Supreme,Superlon,Armacell or equivalent -
-
20 mm dia, 65 Rm 80.00 5,200.0
25 mm dia, 740 Rm 90.00 66,600.0
32 mm dia, 562 Rm 100.00 56,200.0
40 mm dia, 350 Rm 120.00 42,000.0
50 mm dia, 240 Rm 150.00 36,000.0
65 mm dia, 320 Rm 160.00 51,200.0
80 mm dia, 10 Rm 180.00 1,800.0
100 mm dia, 80 Rm 200.00 16,000.0
125 mm dia, 30 Rm 225.00 6,750.0
150 mm dia, 36 Rm 250.00 9,000.0
200 mm dia, 102 Rm 300.00 30,600.0
250 mm dia, 48 Rm 350.00 16,800.0
300 mm dia, 54 Rm 380.00 20,520.0
-
8.0 Room Thermostat for Room FCU: 152 Set 550.00 83,600.0
Supply, installation, testing & commissioning of The thermostat shall Control 2
way chilled water valve, 3 speed fan switch, space temperature indication, space
temperature set point adjustment, as Wired Controller With some IR Remote, -
etc.

-
9.0 Drain Pipe with XLPE Insulation: -

Supply, installation, testing & commissioning of Drain pipe and Insulation

works with all necessary accessories and fittings, Fixing for commissioning of
the equipment including all electrical & Civil works as follows technical -
specification, drawing and time to time site instruction from Consultant / Owner.
Pipe Pressure test should done as per Ashrae Standard.

Insulation material shall be closed Cell Cross Linked Polyethylene

(XLPE)/Nitrile Rubber Foam in the form of pre-formed pipe sections with
aluminum foil facing and complete in all respects as per specifications and
-
drawings on chilled water piping of the following sizes. The insulation material
should be of density 24±2 Kg/m³ & thermal Conductivity not exceeding 0.035
W/m³K at an average Temperature of 23°C. Insulation thickness= 25 mm
During installation contractor should consider existing services and should
-
install without damage of any services
Pipe Brand: N-Poly/RFL -
Country of Manufacture: Bangladesh -
Insulation Brand: Supreme, Superlon, Armacell or equivalent -
-
50mm 200 Rm 90.00 18,000.0
25 mm 500 Rm 70.00 35,000.0
20 mm 400 Rm 60.00 24,000.0
-
10.0 VALVE ACCESSORIES : -
-
10.1 Valves :(Ball/Butterfly) : -

Supply, installation, testing & commissioning of Ball / Butter fly valve shall be
lever-operated type, anti corrosive cast iron body. All should be comply with
-
specification Valve upto 80mm dia shall be welded socket ball type complete
with companion flanges, nut-bolt, gasket etc.

Brand: Tozen, Kitz, nibco, Flowserve, KSB, Pentair -

-
20mm dia (Ball) 21 Nos. 550.00 11,550.0
25mm dia (Ball) 288 Nos. 650.00 187,200.0
32mm dia (Ball) 132 Nos. 650.00 85,800.0
50mm dia (Butterfly) 8 Nos. 750.00 6,000.0
65mm dia (Butterfly) 4 Nos. 750.00 3,000.0
80mm dia (Butterfly) 2 Nos. 1,050.00 2,100.0
100mm dia (Butterfly) 26 Nos. 1,100.00 28,600.0
125mm dia (Butterfly) 4 Nos. 1,200.00 4,800.0
150mm dia (Butterfly) 2 Nos. 1,200.00 2,400.0
200mm dia (Butterfly) 21 Nos. 1,500.00 31,500.0
 250mm dia (Butterfly) 0 Nos. 1,500.00 -
-
10.2 Pressure independent Control Valve(PICV) : -
Supply, installation, testing , commissioning of PICV which shall be connected
with DDC controller for FCU. When the equipment is not running valve shall -
remain close.
Brand: Tozen, Danfoss, Siemens, Belimo, Johnson Control, oventrop -
20mm dia 7 Nos. 550.00 3,850.0
25mm dia 96 Nos. 650.00 62,400.0
32mm dia 44 Nos. 650.00 28,600.0
40mm dia 0 Nos. -
50mm dia 0 Nos. -
100mm dia 4 Nos. 1,050.00 4,200.0
125mm dia 0 Nos. -
200mm dia 0 Nos. -
250mm dia 0 Nos. -
-
10.3 Y-Strainer : -

Supply, installation, testing & commissioning of Strainer shall be bronze body,

-
screwed cover, Y‑ pattern body, Stainless steel screen and flanged end type.

Brand: Tozen, Kitz or equivalent -

-
20mm dia 7 Nos. 550.00 3,850.0
25mm dia 96 Nos. 650.00 62,400.0
32mm dia 44 Nos. 650.00 28,600.0
40mm dia 0 Nos. 1,050.00 -
50mm dia 0 Nos. -
100mm dia 4 Nos. 1,050.00 4,200.0
200mm dia 9 Nos. 1,200.00 10,800.0
-
10.4 Flexible Joint : -

Supply, installation, testing & commissioning of Flexible joint shall be suitable

to absorb shock and system hammering and to reduce vibration transmission.
-
Flexible joint shall be molded neoprene or butyl and suitable to withstand a
temperature of 65°C. Flexible joint shall be spherical in shape.

Brand: Tozen, Kitz, Nibco, Toyo, Metra flex or equivalent -

20mm dia 14 Nos. 550.00 7,700.0
25mm dia 200 Nos. 650.00 130,000.0
32mm dia 88 Nos. 650.00 57,200.0
50mm dia 8 Nos. 1,050.00 8,400.0
100mm dia 8 Nos. 1,200.00 9,600.0
200mm dia 8 Nos. 1,200.00 9,600.0
250mm dia 0 Nos. 1,500.00 -
-
-
-
-
10.6 Manual Balancing Valve with (Adjustable Device) : -

Supply, installation, testing & commissioning of Manual balancing valve shall

be flanged end type suitable for measuring and controlling of water flow through -
pipe and shall be complete with test port, measuring devices.

Brand: Tozen, Kitz or equivalent -

200 mm dia 4 Nos. 1,200.0 4,800.0
250 mm dia Nos. 1,500.0 -
Differential pressure meter & Adjusting kit for MBV -
-
10.7 Automatic Balancing Valve : -

Supply, installation, testing & commissioning of Electric operated Automatic

Balancing shall be single seated, straight through, globe body, normally close
type high lift plug, flanged end type with companion flanges and gasket. The
-
valve shall be operable on system pressure. If system pressure increased it will If not available in
open and by pass water. The valve shall be complete with modulator motor, low local market
voltage transformer, pressure sensor for water pipe, actuator, linkage etc.

250mm dia 0 Nos -

200mm dia 1 Nos 1,500.0 1,500.0
-
10.7 3-way Auto Modulating Valve : -

Supply, installation, testing & commissioning of Electric operated 3-way

modulating valve shall be single seated, straight through, globe body, normally
close type high lift plug, flanged end type with companion flanges and gasket.
-
The valve shall be operable on system pressure. If system pressure increased it
will open and by pass water. The valve shall be complete with modulator motor,
low voltage transformer, pressure sensor for water pipe, actuator, linkage etc.

200mm dia 1 Nos. 3,500.0 3,500.0

250mm dia Nos. 3,500.0 -
-
Brand: Schneider, Siemens, ABB, Delta Control or equivalent -
-
10.10 Flo Trex Valve -
Supply, installation, testing & commissioning of Check valves shall be re-grind
able seat, screwed cap, lift type disc (vertical line), integral seal and flanges end -
type.
Brand: Tozen, Kitz, Nibco, Flowserve, KSB, Pentair, Combi -
-
200mm dia 9 Nos. 1,500.0 13,500.0 0
-
10.9 Auto Vent Valve : -

Supply, installation, testing & commissioning of Automatic vent valve with ball
valve shall be free floating type having test cock, 20 mm threaded outlets to 15 Nos. 650.0 9,750.0
accept drain line and threaded inlet connection. Vent valve shall be 20-mm size.
 Brand: Tozen, Kitz or equivalent -
-
11.0 METERING DEVICE : -

Supply, installation, testing & commissioning of metering device such as

pressure gauge, pipe thermometer, duct thermometer and flow-meter shall be at
location shown in the drawing and as per direction. Required size of bush shall -
be welded on pipe. It shall be water leak proof at a pressure of 10 Kg/cm2.
metering devices shall be installed as per recommendation of the manufacturer.

Brand: Tozen, Shield or equivalent -

-
11.1 Pressure Gauge : 60 Nos. 650.00 39,000.0
Supply, installation, testing & commissioning of Pressure Gauge for water pipe
line shall be of dial type of 100 mm dia suitable to read 0 to 10 Kg pressure.
-
Pressure gauge with ball valve shall be complete with pet cock, pressure
snobber, nipple etc.
-
11.2 Pipe Thermometer : 60 Nos. 650.00 39,000.0
Supply, installation, testing & commissioning of Adjustable angle, direct
reading, industrial type pipe thermometer with shut up valve shall be complete
-
with thermometer well, socket. Thermometer with ball shall be suitable to read
water temperature of range 0 to 50°C.
-
12.0 Ventilation Fan : -
Supply, installation, testing & commissioning of duct type/wall mounted
Galvanized box type fan Fixed driven fan suitable to move substantial amounts
of air at low pressure with minimal energy consumption. The fan motor shall be
single/Three phase and fans shall be complete with centrifugal shutter at external
side and wire mesh guard at internal side. Fan frame shall be constructed from
galvanised steel with a stainless steel impeller. Fans ball bearings shall be sealed
for life time. -
The fan blades shall be truly reversible type SS made & shutter opening
mechanism shall be centrifugal link type push pull system.
The motor type shall be IE3 with IP55 protection.(Sound level shoud be
maintain less than 60db at 1m distance.)

Fan noise lavel should not be more then 35 dB -

Brand: Systemair, Kruger, Nicotra -
-
12.1 Cabinet type Fresh Air Fan(Duct Type): -
Capacity : 4000 cfm, ESP 100 Pa 0 Nos. 2,500.00 -
Capacity : 10000 cfm, ESP 150 Pa (For Basement) 4 Nos. 5,000.00 20,000.0
-
12.2 Cabinet type Exhaust Air Fan(Duct Type): -
Capacity : 800 cfm, ESP 100 Pa 3 Nos. 1,500.00 4,500.0
Capacity : 2000 cfm, ESP 100 Pa 1 No. 2,000.00 2,000.0
Capacity : 5000 cfm, ESP 100 Pa 0 Nos. 2,500.00 -
Capacity : 10000 cfm, ESP 150 Pa (For Basement) 4 Nos. 5,000.00 20,000.0
-
12.3 Kitchen Fresh Air Fan(Duct Type): -
capable of handling hot as oily air -
-
Capacity : 4000 cfm, ESP 100 Pa 1 No. 2,500.00 2,500.0
Capacity : 2500 cfm, ESP 50 Pa 0 No. 1,500.00 -
Capacity : 2000 cfm, ESP 100 Pa 1 Nos. 1,500.00 1,500.0
-
13.4 Kitchen Exhaust Fan(Duct Type): -
Capacity : 5000 cfm, ESP 100 Pa 1 No. -
Capacity : 2500 cfm, ESP 100 Pa 0 50,000.00 -
-
13.5 Toilet Exhaust Fan(Ceiling Suspended Type): -
Capacity : 200 cfm, ESP 50 Pa 6 Nos. 750.00 4,500.0
Capacity : 100 cfm, ESP 50 Pa 9 Nos. 750.00 6,750.0
Capacity : 50 cfm, ESP 50 Pa 14 Nos. 750.00 10,500.0
-
14.6 Exhaust Fan(Wall Type): -
Capacity : 500 cfm, ESP 50 Pa 29 Nos. 1,500.00 43,500.0
Capacity : 100 cfm, ESP 50 Pa 2 Nos. 500.00 1,000.0
14.7 Staire Pressured System -
Inchuding pressure sensor and fire signal receive controller -
6000 CFM, Fresh Air Fan with VFD Drive & Pressure sensor with controllar ,
ESP 200 Pa.( for.Stair case) 1 Nos. 3,000.00 3,000.0

12000 CFM, Fresh Air Fan , ESP 150 Pa.( for.Stair case) 1 Nos. 5,000.00 5,000.0
-
14.6 Jet Fan with silencer: -

Supply & Installation of ceiling mounted Impulse Two speed type jet fans are
suitable for ventilation of larger buildings where space limitaiton is substantial
and duct work should be avoided. By adding momentum to the air the jet vent
thrusts air to the desired point and generates comfort velocity. Each fan shall be
complete with dual speed motor, casing made of sheet steel duly MS Powder
coated, die cast aluminium impeller, mounting arrangements, Powder coated
-
mild steel outlet deflector and zinc plated inlet guard with silencer. Fans shall be
capable of delivering 2800 cfm air against a minimum thrust of 86N at full load
and 2800 cfm air against a minimum thrust of 22N to successfully throw the air
in the entire region. Fan frame shall be constructed from galvanised steel with a
alluminium alloy impeller. Fans ball bearings shall be sealed for lifetime & Low
Noise type(Sound level shoud be maintain less than 60db at 1m distance)

Capacity : 2800 cfm 3 Nos. 1,800.00 5,400.0

Capacity : 2800 cfm 4 Nos. 1,800.00 7,200.0
-
15.0 Air Terminal : -
 Supply & installation of Air terminal with necessary frame,fitting,gasket and
adjustment items. -
-
15.1 Supply Air Grille -

Supply & installation of Aluminum Louvered ceiling Diffuser with back damper
and plenum shall be selected to confirm face for adjustable horizontal discharge
airflow. At typical flow rates, isothermal throws of 6 to 16 feet with 37 NC
level . The diffuser shall have an easily removable core with fixed blades in 1, 2,
3, or 4-way configurations. The manufacturer shall provide published (printed or
electronic) performance data for the diffuser. The diffuser shall be tested in
-
accordance to the data standards at the time of product introduction or
ANSI/ASHRAE Standard 70.
Linear slot diffuser, plenum shall be attached to the linear by means of spring
clips to allow for plenum removal without use of special tools.Selection chart
should be provided based on required CFM which are indicated in drawing to
get approval.

Brand: Systemair, TROX, Titus, Price, Ruskin, Halton or equivalent -

-
Neck Size: 4975 x 200 mm 3 Nos. 1,500.00 4,500.0
Neck Size: 400 x 400 mm 31 Nos. 500.00 15,500.0
Neck Size: 450 x 450 mm 91 Nos. 500.00 45,500.0
Neck Size: 1500 x 100 mm 4 Nos. 750.00 3,000.0
Neck Size: 1500 x 75 mm 27 Nos. 750.00 20,250.0
Neck Size: 1200 x 200 mm 4 Nos. 500.00 2,000.0
Neck Size: 1200 x 100 mm 233 Nos. 500.00 116,500.0
Neck Size: 1700 x 75 mm 4 Nos. 850.00 3,400.0
Neck Size: 900 x 200 mm 2 Nos. 500.00 1,000.0
Neck Size: 900 x 100 mm 18 Nos. 500.00 9,000.0
Neck Size: 600 x 100 mm 76 Nos. 500.00 38,000.0
Neck Size : Dia 300 mm(Round Diffuser) 58 Nos. 500.00 29,000.0
Neck Size: 1200 x 150 mm 16 Nos. 500.00 8,000.0
-
15.2 Exhaust Air Louver With insect screen: -
Supply, installation, testing & commissioning of extruded aluminium Exhaust
Air Louver With insect screen terminal with mat finishing of approved colour on
the air distribution duct line /coller / ceiling etc. including supply and -
installation of necessary fixing screw, gasket , necessary insulation( if required)
etc.
-
Neck Size: 600 x 250 mm 3 Nos. 500.00 1,500.0
-
15.3 Return Air Liner Bar Grille : -
Neck Size: 350 x 350 mm 2 Nos. 500.00 1,000.0
Neck Size: 300 x 300 mm 32 Nos. 500.00 16,000.0
Neck Size: 1200 x 150 mm 16 Nos. 500.00 8,000.0
-
15.4 Service Door With Return Grill : -
Neck Size: 1200 x 600 mm 130 Nos. 850.00 110,500.0
-
16.0 DUCT WORK: -

Supply, fabrication and installation of galvanized sheet steel duct work complete
with bends, Tees, reducers, branch takeoffs, air chamber etc. as per direction and
drawing. Hangers, brackets, stiffeners and isolator boxes shall be fabricated with
M.S. angle/F.I. bar or rod as per drawing and direction and shall be galvanized.
Duct shall be constructed with best-bloomed galvanized sheet steel. Before
-
installation of duct, inside and outside shall be cleaned from any dust. Between
flanges, for flanged end duct, approved type of gasket shall be used. Approved
type of sealing compound shall be used to make the duct work leak-proof. Duct
shall be hanged or supported at an interval of not more than 1.8 meter.

24 BWG 5000 sqm 750.00 3,750,000.0

22 BWG 1000 sqm 750.00 750,000.0
20 BWG 500 sqm 750.00 375,000.0
-
Brand: ZincCoat or equivalent -
-
16.1 Flexible Ducting : -
Supply, installation, testing & commissioning of UL Listed CIRCULAR pre-
insulated fire retardant spiral flexible duct made of aluminium foil insulated -
using fibre glass - 14 Kg per cum density

Brand: MEGA/ equivalent -

-
Ø300mm 300 Rm 500.00 150,000.0
Ø200mm 200 Rm 500.00 100,000.0
-
17.0 Duct Insulation: -

Supply, installation, testing & commissioning of Duct lining materials shall be

25 mm thick rock-wool complete with aluminum foil perforated surface liner,
fixing pin, tape, adhesive etc. complete. Density of lining materials shall not be
less than 48 kg/cum. Duct lining materials shall be installed inside sound 6000 sqm 350.00 2,100,000.0
reducing box and mixing box for the fan coil units. Before fixing the duct
surface shall be cleaned properly. Proper type of adhesive, pin, glue etc. shall be
used. Installation shall be as per drawing and direction of Engineer.

Brand: Armacell, Supreme, Superlon or equivalent. -

-
18.0 Duct Acoustic Lining: 2500 sqm 350.00 875,000.0
Supply, installation, testing & commissioning of 24 mm thick duct acoustic
lining made of open cell nitrile rubber, specially prepared for duct acoustic.
-
Lining shall have self adhesive for fixing with duct. Density shall be 140 to 180
kg/m³.
 Brand: Armacell, Supreme, Superlon or equivalent. -
Country of Manufacture: India/Malaysia or equivalent. -
-
19.0 VOLUME CONTROL DAMPER : -
Supply & installation of volume control damper constructed with 18 BWG sheet
steel painted with 2 coats of synthetic black paint, adjustable locking
50 sqm 3,228.00 161,400.0
arrangement from outside of duct and suitable to mount on flanged end duct as
per drawings and direction of the Engineer (local made) .
Brand: Halton, TROX, Price, Ruskin, System Air or equivalent -
-
20.0 Non Return Damper : -

Supply and installation of opposed blade type Non return damper constructed
with 18 BWG sheet steel painted with two coats of synthetic black paint. The
damper shall have adjustable locking arrangement with worm gear operable
50 sqm 3,228.00 161,400.0
from outside duct work and shall be flanged end type suitable to mount on
flanged end duct work. Non return dampers shall be as per layout drawings and
direction.

Brand: Halton, TROX, Price, Ruskin, System Air or equivalent -

-
21.0 Electromagnetic Flow Meter: -

Supply of Electromagnetic flow meter for constant measuring flow of the piping
system shall be constructed from high grade steel / alloy steel with flange end,
leak proof gasket ,suitable for working pressure up to 300 psig and complete -
with SENSORPROM unit for automatically uploads calibration values and
setting ete compatible operation of BMS etc.

Brand: Siemens, ABB, Johnson Controls or equivalent -

-
150mm dia 1 Nos. 1,200.0 1,200.0
200mm dia 1 Nos. 1,500.0 1,500.0
250mm dia 2 Nos. 1,500.0 3,000.0
-
22.0 EXPANSION TANK (Close Type) : 1 Job 16,000.0 16,000.0

Supply, installation, testing & commissioning of expansion tank constructed

with 18 BWG galvanized sheet steel having connection for expansion pipe, feed
water line and over flow line. The tank shall be installed on steel framing at a
-
height of at least 1.5 meter from top level of chilled water pipe. The tank shall be
insulated with 25 mm thick insulation and plastered with 25 mm thick mortar
over chicken wire mesh. Tank size shall be 750 lit.

Brand: Reflex or equivalent -

-
23.0 WATER SOFTNER PLANT : 1 Set. 35,000.0 35,000.0

Supply, Installation, Testing & Commissioning of Vertical pressure type Water

Softener made out of MSEP / FRP composite vessel with top and bottom
openings, self-supporting legs, suitable distribution and collection system, initial -
charge of Resin, pressure gauges, sampling cock, air vent, frontal MS piping,
diaphragm valves for inlet, backwash outlet etc. complete

The price shall be included all chemical items for one year. -
The design parameter shall be fixed based on the water quality and test report. -
Capacity :50 gpm -
Operating pressure - 3.5 + 0.5 Kg/cm2 -
Testing pressure - 10 Kg/cm2 -
Input water hardness - 100 ppm or design as per parameter -
Outlet water hardness - Not exceeding 20 ppm or design as per parameter -
Regeneration Cycle - 24 hours -
Brand: -
Country of Manufacture: -
Country of Origin: -
-
24.0 Dirt and Air separator : 2 Nos. 3,500.0 7,000.0
Supply, installation, testing and commissioning of dirt and air separator with
proper sized shutoff valve at both end in a combination of air & sediment
separator that utilizes a coalescing medium to remove impurities from HVAC
systems. It features a stainless steel coalescing medium with 58% open area,
removable end cover for coalescing medium -
access, and connections for an air vent, blow down valve, and skim valve. The
product is designed, constructed, inspected and
stamped per ASME Section VIII, Division 1

Construction material -
Shell: Carbon Steel
Coalescing Medium: Stainless Steel -
Maximum working pressure 150 Psig -
Flow rate= 1680 US GPM -
-
25.0 MAKE-UP WATER TANK WITH FLOAT VALVE: 1 Set. 5,000.0 5,000.0
Supply, installation, testing & commissioning of high quality PVC/Plastic make-
up water Tank along with adequately rated make-up water pump, for make-up of
water for cooling towers. The tank shall have connection for, feed water line, -
overflow line, drain line etc. complete in all respect. Cooling Tower Capacity
1680 GPM
Brand:Carno or equivalent -
-
26.0 Chemical Dosing System: 1 Set. 7,500.0 7,500.0
Supply of include with auto feed type suitable to handle of chilled water to
control corrosion, scale and biological effect and shall be complete with dosing
-
pumps, sensor, control valves, PVC tubes and tube fittings for chemical feed, pH
analyzer and indicator etc. complete.
Brand: Microdos/ Nalco/ X-Pot or equivalent -
-
27.0 Side Stream Filter System: 1 Set. 12,500.0
 Supply, installation, testing & commissioning of side stream filter system
include with Pump and accessories to ensure continuously filter a portion of
cooling water to remove debris and particles. Side stream filtration requires a
minimum supply pressure to account for the inherent differential pressure drop
-
across the filter typically ranges from 20 to 30 psi. All side stream filters have a
maximum working pressure; sand filters have a threshold of 80 psi. Systems
require cleaning of filters or holding chambers to remove debris and particles
that are trapped in filters.

System handling capacity is 100 gpm and residual head- 20 meter after filtration. -

Capacity: 100 gpm; Residual Head after filtration= 20 m -

-
28.0 Performance Test / Check at Factory (or PSI) : -
Performance Test / Check at Factory (or PSI) : Before shipment the main
product vendor/contractor should arrange the Performance test arrangement for
the mail product at Manufacturer factory lab for Consultant and Client 1 Job -
person.There should have testing arrangement as per standard procedure at
factory test facility area .
-
29.0 Cladding of Pipe: 200 sqm 850.0

Supply, installation, testing & commissioning of Jacketing shall be done with 26

-
SWG Aluminum sheet. Weather proof sealant to be used at all joining places.

Brand: Zinc Coat or equivalent -

-
30.0 Testing Port : -
Supply, installation, testing & commissioning of In supply and return pipe
contractor should install a testing port having threaded end cap ,ball valve and
capable to insert thermometer/ temperature gauge when required for pressure 160 Nos. -
gauge and temperature gauge
-
31.0 Intumescent Sealant : -

Supply, installation, testing and commissioning of fire barrier sealant which

shall be a one component, ready-to-use, gun-grade, latex-ased,intumescent fire
stop sealant capable of expanding a minimum of three times its dried volume
when exposed to temperatures above 1000°F (538°C). The material shall be
thixotropic and shall be applicable to overhead, vertical and horizontal fire stops.
The sealant shall be listed by independent test agencies such as UL, Intertie or
100 L -
FM. Fire Barrier Sealant shall be tested to and pass the criteria of ASTM E 814
(UL 1479) Standard Test Method for Fire Tests of Penetration Fire stop
Systems, ASTM E 1966 (UL 2079) Standard Test Method for Fire Resistive
Joint Systems and CAN/ULC S115 Standard Method of Fire Tests of Fire stop
Systems.
N.B: During Shop drawing this quantity may subject to change

Brand: 3M, Dupont or equivalent -

-
32.0 Testing, Commissioning and Balancing and Drawings: 1 Job -
After proper installation and certification the system shall be tested,
commissioned and balanced as per direction and recommendation by the
-
Manufacturer as well as HVAC Designer. Contractor shall do (but not limited
to) following works under this clause.
a. Prepare and submit shop drawing , As built drawing, Commissioning protocol
-
and get approval from Consultant.
b. Carry out duct inspection -
c. Carry out pipe pressure testing -
d. Carry our Electrical Cabling testing -
e. Testing of condensate water drainage slope with water -
f. Safety protection and cut-outs shall be tested individually -
g. Commissioning of Automatic Control system -
Balancing and Adjusting of HVAC system -

Balancing and adjusting of the system should be in a process to optimize the

HVAC system to ensure that air conditioning outputs(desired air flow, chilled
-
water flow, desired air out temperature from diffuser etc.) are consistent, and
temperatures are attained in all rooms as per design and drawing

-
33.0 Chilled Water Balancing: 1 Job 70,000.0
Chilled water balancing shall apply a disciplined procedure of adjustment to
water flow rates throughout the chilled water system to meet the particular
requirement of the design drawing. Following but not limited to should be -
followed during balancing

34.0 Air Balancing: 1 Job 150,000.0

Purpose of air balancing is to define the step by step method to implement the
correct practice for the air balancing to ensure the job execution complies with
the project requirements and serve the intended function to the satisfactory level -
( as per design and drawing). Ensure air flow capacity and temperature as per
design and drawing

All testing and commissioning works must be documented room wise/zone wise
in approved formats. All of these document's must be jointly witnessed and -
signed by the Client and Contractor's authorized Engineer.

-
35.0 Engineering Team : Start from Mobilization 1 Job -
Senior engineer with design knowledge to prepare modification , reporting and
-
perform meeting( Should be conversant in English)
Site Supervisor Engineer, construction management team , drafting and drawing
-
preparation team.

Team also be capable of prepare shop drawing, and as built drawing, time to
-
time approval from consultant or project authorized person from client

-
36.0 DOCUMENTATION : 1 Job -
 Detail layout and fabrication drawing shall be prepared as per guide line layout
drawing and shall be submitted for approval. Modification drawing shall be
prepared as per site condition. Layout drawings shall be coordinated with other
services. Required section and detail shall be prepared. Construction work shall
-
be done as per approved working drawings. Compilation of all the document
such as built drawing, testing, commissioning & balancing report, operation and
maintenance manuals etc. shall be done as per direction. Drawings shall be
prepared on Auto Cad.

-
37.0 OPERATION AND MAINTENANCE: 2 Year -

After completion of warranty period, operation and maintenance will be started

as per tender instruction. A full time operator and maintenance engineer (B.Sc..
Mechanical) shall be deputed at site during operation and maintenance work.
During operation and maintenance if any defect in installation work is detected, -
shall be rectified by the contractor at no extra cost. Logbook to record
performance of the system shall be maintained as follows technical
specification, drawing and time to time site instruction from Consultant / Owner.

TOTAL BDT 12,047,370.0

Vat7% 843,315.9
TOTAL BDT 12,890,685.90

Received By