SAFETY DATA SHEET

1. Identification
Product identifier Liquid Wrench Penetrant & Lubricant
Other means of identification
SDS number LED411
Part No. LED411
Tariff code 3403.19.1000
Recommended use Penetrant/Lubricant
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name RSC Chemical Solutions
Address 600 Radiator Road
Indian Trail, NC 28079
United States
Telephone Customer Service: (704) 821-7643
Technical: (704) 821-7643
Website www.rscbrands.com
E-mail [email protected]
Emergency phone number Emergency Telephone: (303) 623-5716
Emergency Contact: RMPDC (877) 740-5015

2. Hazard(s) identification
Physical hazards Flammable aerosols Category 1
Health hazards Skin corrosion/irritation Category 2
Serious eye damage/eye irritation Category 2
Sensitization, skin Category 1B
Specific target organ toxicity, single exposure Category 3 narcotic effects
Aspiration hazard Category 1
Environmental hazards Hazardous to the aquatic environment, Category 2
long-term hazard
OSHA defined hazards Not classified.

Label elements

Signal word Danger

Hazard statement Extremely flammable aerosol. May be fatal if swallowed and enters airways. Causes skin irritation.
May cause an allergic skin reaction. Causes serious eye irritation. May cause drowsiness or
dizziness. Toxic to aquatic life with long lasting effects.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open
flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Avoid
breathing gas. Avoid breathing mist or vapor. Wash thoroughly after handling. Use only outdoors
or in a well-ventilated area. Contaminated work clothing must not be allowed out of the workplace.
Avoid release to the environment. Wear eye protection/face protection. Wear protective gloves.

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 1 / 10

 Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Wash
with plenty of water. If inhaled: Remove person to fresh air and keep comfortable for breathing. If
in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and
easy to do. Continue rinsing. Call a poison center/doctor if you feel unwell. If skin irritation or rash
occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention. Take
off contaminated clothing and wash before reuse. Collect spillage.
Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up. Protect from
sunlight. Do not expose to temperatures exceeding 50°C/122°F.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise Combustible.
classified (HNOC)
Supplemental information 77.78% of the mixture consists of component(s) of unknown acute oral toxicity. 77.78% of the
mixture consists of component(s) of unknown acute dermal toxicity. 89.91% of the mixture
consists of component(s) of unknown acute inhalation toxicity. 81.68% of the mixture consists of
component(s) of unknown acute hazards to the aquatic environment. 35.66% of the mixture
consists of component(s) of unknown long-term hazards to the aquatic environment.

NOTE: This product is a consumer product and is labeled in accordance with the US Consumer
Product Safety Commission regulations which take precedence over OSHA Hazard
Communication labeling. The container label may not include the OSHA label elements listed in
this document. Always carefully review the entire SDS and the product label prior to use in the
workplace.

3. Composition/information on ingredients
Mixtures
Chemical name Common name and synonyms CAS number %
Distillates (petroleum), 64742-47-8 40 - < 50
Hydrotreated Light
2-(2-butoxyéthoxy) Éthanol 112-34-5 10 - < 20
Distillates (petroleum), 64742-52-5 10 - < 20
Hydrotreated Heavy Naphthenic
1,6,10-dodecatriene, 1581740-29-5 5 - < 10
7,11-dimethyl-3-methylene-, (6e)-,
Hydrogenated
Soybean Oil 8001-22-7 5 - < 10
Corrosion Inhibitor Mixture 3-<5
Carbon Dioxide 124-38-9 1-<3
Oleoyl Sarcosine 110-25-8 < 0.3
Bht (butylated Hydroxytoluene) 128-37-0 < 0.2
Other components below reportable levels 3-<5
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.

4. First-aid measures
Inhalation Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Skin contact Remove contaminated clothing immediately and wash skin with soap and water. In case of
eczema or other skin disorders: Seek medical attention and take along these instructions. Wash
contaminated clothing before reuse.
Eye contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.
Ingestion Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If
vomiting occurs, keep head low so that stomach content doesn't get into the lungs.
Most important Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.
symptoms/effects, acute and Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,
delayed redness, swelling, and blurred vision. Skin irritation. May cause redness and pain. May cause an
allergic skin reaction. Dermatitis. Rash.
Indication of immediate Provide general supportive measures and treat symptomatically. Keep victim under observation.
medical attention and special Symptoms may be delayed.
treatment needed
General information Ensure that medical personnel are aware of the material(s) involved, and take precautions to
protect themselves. Wash contaminated clothing before reuse.

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 2 / 10

5. Fire-fighting measures
Suitable extinguishing media Alcohol resistant foam. Powder. Dry chemicals. Carbon dioxide (CO2).
Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire.
media
Specific hazards arising from Contents under pressure. Pressurized container may explode when exposed to heat or flame.
the chemical During fire, gases hazardous to health may be formed.
Special protective equipment Firefighters must use standard protective equipment including flame retardant coat, helmet with
and precautions for firefighters face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Fire fighting Move containers from fire area if you can do so without risk. Cool containers exposed to heat with
equipment/instructions water spray and remove container, if no risk is involved. Containers should be cooled with water to
prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or
monitor nozzles, if possible. If not, withdraw and let fire burn out.
Specific methods Use standard firefighting procedures and consider the hazards of other involved materials. Move
containers from fire area if you can do so without risk. In the event of fire and/or explosion do not
breathe fumes.
General fire hazards Extremely flammable aerosol. Combustible.

6. Accidental release measures

Personal precautions, Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
protective equipment and appropriate protective equipment and clothing during clean-up. Avoid breathing mist or vapor.
emergency procedures Avoid breathing gas. Do not touch damaged containers or spilled material unless wearing
appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities
should be advised if significant spillages cannot be contained.
Methods and materials for Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without
containment and cleaning up risk. Move the cylinder to a safe and open area if the leak is irreparable. Use water spray to reduce
vapors or divert vapor cloud drift. Isolate area until gas has dispersed. Keep combustibles (wood,
paper, oil, etc.) away from spilled material. Prevent product from entering drains. Absorb in
vermiculite, dry sand or earth and place into containers. Following product recovery, flush area
with water.

Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
Environmental precautions Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into
drains, water courses or onto the ground.

7. Handling and storage

Precautions for safe handling Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing
or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when
handling the product must be grounded. Do not re-use empty containers. Avoid breathing mist or
vapor. Avoid breathing gas. Avoid contact with eyes, skin, and clothing. Avoid prolonged or
repeated contact with skin. Avoid prolonged exposure. Use only in well-ventilated areas. Wear
appropriate personal protective equipment. Wash hands thoroughly after handling. Avoid release
to the environment. Observe good industrial hygiene practices.
Conditions for safe storage, Level 2 Aerosol.
including any incompatibilities
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Keep out of the reach of children.

8. Exposure controls/personal protection

Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components Type Value Form

Carbon Dioxide (CAS PEL 9000 mg/m3

124-38-9)
5000 ppm

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 3 / 10

 US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
Components Type Value Form

Distillates (petroleum), PEL 5 mg/m3 Mist.

Hydrotreated Heavy
Naphthenic (CAS
64742-52-5)
2000 mg/m3
500 ppm
Distillates (petroleum), PEL 400 mg/m3
Hydrotreated Light (CAS
64742-47-8)
100 ppm
Soybean Oil (CAS PEL 5 mg/m3 Respirable fraction.
8001-22-7)
15 mg/m3 Total dust.

US. ACGIH Threshold Limit Values

Components Type Value Form

2-(2-butoxyéthoxy) Éthanol TWA 10 ppm Inhalable fraction and

(CAS 112-34-5) vapor.
Bht (butylated TWA 2 mg/m3 Inhalable fraction and
Hydroxytoluene) (CAS vapor.
128-37-0)
Carbon Dioxide (CAS STEL 30000 ppm
124-38-9)
TWA 5000 ppm
Distillates (petroleum), TWA 5 mg/m3 Inhalable fraction.
Hydrotreated Heavy
Naphthenic (CAS
64742-52-5)
US. NIOSH: Pocket Guide to Chemical Hazards
Components Type Value Form

Bht (butylated TWA 10 mg/m3

Hydroxytoluene) (CAS
128-37-0)
Carbon Dioxide (CAS STEL 54000 mg/m3
124-38-9)
30000 ppm
TWA 9000 mg/m3
5000 ppm
Distillates (petroleum), Ceiling 1800 mg/m3
Hydrotreated Heavy
Naphthenic (CAS
64742-52-5)
STEL 10 mg/m3 Mist.
Soybean Oil (CAS TWA 5 mg/m3 Respirable mist.
8001-22-7)
10 mg/m3 Total mist
Biological limit values No biological exposure limits noted for the ingredient(s).
Appropriate engineering Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
controls should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Provide
eyewash station. Eye wash fountain and emergency showers are recommended.
Individual protection measures, such as personal protective equipment
Eye/face protection Not available.
Skin protection
Hand protection Wear appropriate chemical resistant gloves.
Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 4 / 10

 Other Wear appropriate chemical resistant clothing.
Respiratory protection Chemical respirator with organic vapor cartridge and full facepiece. Chemical respirator with
organic vapor cartridge and full facepiece if threshold limits are exceeded.
Thermal hazards Wear appropriate thermal protective clothing, when necessary.

General hygiene When using do not smoke. Always observe good personal hygiene measures, such as washing
considerations after handling the material and before eating, drinking, and/or smoking. Routinely wash work
clothing and protective equipment to remove contaminants. Contaminated work clothing should not
be allowed out of the workplace.

9. Physical and chemical properties

Appearance Opaque Liquid
Physical state Liquid, Gas.
Form Aerosol.
Color Light brownto Tan.
Odor Sweet Vanilla
Odor threshold Not available.
pH Not available.
Melting point/freezing point -90.58 °F (-68.1 °C) estimated
Initial boiling point and boiling 446.72 °F (230.4 °C) estimated
range
Flash point > 200.0 °F (> 93.3 °C) Tag Closed Cup
Evaporation rate Not available.
Flammability (solid, gas) Not applicable. Not available.
Upper/lower flammability or explosive limits
Flammability limit - lower 0.7 % estimated
(%)
Flammability limit - upper 5 % estimated
(%)
Explosive limit - lower (%) Not available.
Explosive limit - upper (%) Not available.
Vapor pressure 8.72 hPa estimated
Vapor density Not available.
Relative density Not available.
Solubility(ies)
Solubility (water) Not available.
Partition coefficient Not available.
(n-octanol/water)
Auto-ignition temperature 442 °F (227.78 °C) estimated
Decomposition temperature Not available.
Viscosity Not available.
Other information
Density 6.93 lbs/gal
Explosive properties Not explosive.
Flame extension > 31 in
Flammability (flash back) No
Heat of combustion (NFPA 27.16 kJ/g estimated
30B)
Oxidizing properties Not oxidizing.
Percent volatile 14.63 % estimated
Specific gravity 0.83
VOC < 1 % w/w

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 5 / 10

10. Stability and reactivity
Reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability Material is stable under normal conditions.
Possibility of hazardous No dangerous reaction known under conditions of normal use.
reactions
Conditions to avoid Avoid temperatures exceeding the flash point. Contact with incompatible materials.
Incompatible materials Strong oxidizing agents.
Hazardous decomposition No hazardous decomposition products are known.
products

11. Toxicological information

Information on likely routes of exposure
Inhalation May cause drowsiness and dizziness. Headache. Nausea, vomiting. Prolonged inhalation may be
harmful.
Skin contact Causes skin irritation. May cause an allergic skin reaction.
Eye contact Causes serious eye irritation.
Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious
chemical pneumonia.
Symptoms related to the Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.
physical, chemical and Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,
toxicological characteristics redness, swelling, and blurred vision. Skin irritation. May cause redness and pain. May cause an
allergic skin reaction. Dermatitis. Rash.
Information on toxicological effects
Acute toxicity May be fatal if swallowed and enters airways.
Components Species Test Results
2-(2-butoxyéthoxy) Éthanol (CAS 112-34-5)
Acute
Dermal
LD50 Rabbit 2700 mg/kg
Oral
LD50 Rat 4500 mg/kg
Bht (butylated Hydroxytoluene) (CAS 128-37-0)
Acute
Oral
LD50 Rat 890 mg/kg

* Estimates for product may be based on additional component data not shown.
Skin corrosion/irritation Causes skin irritation.
Serious eye damage/eye Causes serious eye irritation.
irritation
Respiratory or skin sensitization
Respiratory sensitization Not a respiratory sensitizer.
Skin sensitization May cause an allergic skin reaction.
Germ cell mutagenicity No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Carcinogenicity Not classifiable as to carcinogenicity to humans.
IARC Monographs. Overall Evaluation of Carcinogenicity
Bht (butylated Hydroxytoluene) (CAS 128-37-0) 3 Not classifiable as to carcinogenicity to humans.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
US. National Toxicology Program (NTP) Report on Carcinogens
Not listed.
Reproductive toxicity This product is not expected to cause reproductive or developmental effects.

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 6 / 10

Specific target organ toxicity - May cause drowsiness and dizziness.
single exposure
Specific target organ toxicity - Not classified.
repeated exposure
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects Prolonged inhalation may be harmful.

12. Ecological information

Ecotoxicity Toxic to aquatic life with long lasting effects.
Components Species Test Results
2-(2-butoxyéthoxy) Éthanol (CAS 112-34-5)
Aquatic
Fish LC50 Bluegill (Lepomis macrochirus) 1300 mg/l, 96 hours
Bht (butylated Hydroxytoluene) (CAS 128-37-0)
Aquatic
Crustacea EC50 Water flea (Daphnia pulex) 1.44 mg/l, 48 hours
Distillates (petroleum), Hydrotreated Light (CAS 64742-47-8)
Aquatic
Crustacea EC50 Water flea (Daphnia pulex) 2.7 - 5.1 mg/l, 48 hours
Fish LC50 Rainbow trout,donaldson trout 2.9 mg/l, 96 hours
(Oncorhynchus mykiss)

* Estimates for product may be based on additional component data not shown.
Persistence and degradability
Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
1,6,10-dodecatriene, 7,11-dimethyl-3-methylene-, (6e)-, 6.08 - 6.48 OECD 117, Log Kow
Hydrogenated
2-(2-butoxyéthoxy) Éthanol 0.56
Mobility in soil No data available.
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.

13. Disposal considerations

Disposal instructions Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents
under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into
sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used
container. Dispose of contents/container in accordance with local/regional/national/international
regulations.
Local disposal regulations Dispose in accordance with all applicable regulations.
Hazardous waste code The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Waste from residues / unused Dispose of in accordance with local regulations. Empty containers or liners may retain some
products product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Contaminated packaging Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal. Do not re-use empty containers.

14. Transport information

DOT
UN number Not available.
UN proper shipping name Consumer Commodity
Transport hazard class(es)
Class ORM-D
Subsidiary risk -
Packing group Not available.
Special precautions for user Not available.
Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 7 / 10

 Packaging exceptions 306
Packaging non bulk 302, 304
Packaging bulk 302, 314, 315
IATA
UN number UN1950
UN proper shipping name Aerosol, flammable
Transport hazard class(es)
Class 2.1
Subsidiary risk -
Packing group Not available.
Environmental hazards Yes
Special precautions for user Not available.
IMDG
UN number UN1950
UN proper shipping name Aerosols, MARINE POLLUTANT
Transport hazard class(es)
Class 2.1
Subsidiary risk -
Packing group Not available.
Environmental hazards
Marine pollutant Yes
EmS F-D, S-U
Special precautions for user Not available.
Transport in bulk according to Not established.
Annex II of MARPOL 73/78 and
the IBC Code
IATA; IMDG

Marine pollutant

General information IMDG Regulated Marine Pollutant.

15. Regulatory information

US federal regulations This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
2-(2-butoxyéthoxy) Éthanol (CAS 112-34-5) Listed.
SARA 304 Emergency release notification
Not regulated.
Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 8 / 10

 OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)
Not regulated.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
SARA 302 Extremely hazardous substance
Not listed.
SARA 311/312 Hazardous No (Exempt)
chemical
SARA 313 (TRI reporting)
Chemical name CAS number % by wt.
2-(2-butoxyéthoxy) Éthanol 112-34-5 10 - < 20
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
2-(2-butoxyéthoxy) Éthanol (CAS 112-34-5)
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Safe Drinking Water Act Not regulated.
(SDWA)
US state regulations California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material
is not known to contain any chemicals currently listed as carcinogens or reproductive toxins.
California Proposition 65
US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,
subd. (a))
2-(2-butoxyéthoxy) Éthanol (CAS 112-34-5)
Distillates (petroleum), Hydrotreated Heavy Naphthenic (CAS 64742-52-5)
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
Australia Australian Inventory of Chemical Substances (AICS) Yes
Canada Domestic Substances List (DSL) No
Canada Non-Domestic Substances List (NDSL) No
China Inventory of Existing Chemical Substances in China (IECSC) No
Europe European Inventory of Existing Commercial Chemical No
Substances (EINECS)
Europe European List of Notified Chemical Substances (ELINCS) No
Japan Inventory of Existing and New Chemical Substances (ENCS) No
Korea Existing Chemicals List (ECL) No
New Zealand New Zealand Inventory No
Philippines Philippine Inventory of Chemicals and Chemical Substances No
(PICCS)
Taiwan Taiwan Chemical Substance Inventory (TCSI) No
United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).

16. Other information, including date of preparation or last revision

Issue date 02-08-2017
Revision date 10-24-2018
Version # 05
HMIS® ratings Health: 3*
Flammability: 1
Physical hazard: 0
NFPA ratings Health: 2
Flammability: 1
Instability: 0

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 9 / 10

NFPA ratings
1
2 0

Disclaimer The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information given is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and is
not to be considered a warranty or quality specification. The information relates only to the specific
material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
Revision information Physical & Chemical Properties: Multiple Properties
HazReg Data: International Inventories
GHS: Classification

Material name: Liquid Wrench Penetrant & Lubricant SDS US

LED411 Version #: 05 Revision date: 10-24-2018 Issue date: 02-08-2017 10 / 10