ORDER NO.

CRT5220
FH-X700BT/XNUC

CD RDS RECEIVER

FH-X700BT /XNUC

FH-X700BT/XNEW5
FH-X755BT/XNES
FH-X759BT/XNID
This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks

CX-3287 CRT4759 S11.6STD CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2012
K-ZZZ SEPT. 2012 Printed in Japan
 1 2 3 4

SAFETY INFORMATION
CAUTION
A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
B
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:

- Safety Precautions for those who Service this Unit.

When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.

C Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.

CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION
This product is a class 1 laser product classi-
fied under the Safety of laser products, IEC
D
60825-1:2007, and contains a class 1M laser
module. To ensure continued safety, do not re-
move any covers or attempt to gain access to
the inside of the product. Refer all servicing to
qualified personnel.

CAUTION—CLASS 1M INVISIBLE LASER

RADIATION WHEN OPEN, DO NOT VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS.
E

WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.

FH-X700BT/XNUC
2
1 2 3 4
 5 6 7 8

Laser diode characteristics

Wave length : 785 nm to 814 nm
A
Maximum output : 1 190 µW(Emitting period : unlimited)

Additional Laser Caution

Transistors Q101 in PCB drive the laser diodes.
When Q101 is shorted between their terminals, the laser diodes will radiate beam.
If the top cover is removed with no disc loaded while such short-circuit is continued,
the naked eyes may be exposed to the laser beam.

CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacturer. C

Discord used batteries according to the manufacturer's instructions.

FH-X700BT/XNUC
5 6 7 8
3
 1 2 3 4

CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS ........................................................................................................................ 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 5
2. SPECIFICATIONS ............................................................................................................................................ 6
2.1 SPECIFICATIONS ..................................................................................................................................... 6
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 9
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 10
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 10
3.2 PCB LOCATIONS .................................................................................................................................... 10
3.3 JIGS LIST .................................................................................................................................................11
3.4 CLEANING................................................................................................................................................11
4. BLOCK DIAGRAM.......................................................................................................................................... 12
5. DIAGNOSIS.................................................................................................................................................... 14
B 5.1 OPERATIONAL FLOWCHART ................................................................................................................ 14
5.2 ERROR CODE LIST ................................................................................................................................ 15
5.3 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 18
6. SERVICE MODE ............................................................................................................................................ 19
6.1 DISPLAY TEST MODE 1 ......................................................................................................................... 19
6.2 DISPLAY TEST MODE 2 ......................................................................................................................... 20
6.3 SOFTWARE VERSION UP METHOD ..................................................................................................... 21
6.4 CD TEST MODE ...................................................................................................................................... 22
7. DISASSEMBLY .............................................................................................................................................. 23
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 28
8.1 CD ADJUSTMENT................................................................................................................................... 28
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 29
C
8.3 PCL OUTPUT CONFIRMATION.............................................................................................................. 31
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 32
9.1 PACKING ................................................................................................................................................. 32
9.2 EXTERIOR(1) .......................................................................................................................................... 36
9.3 EXTERIOR(2) .......................................................................................................................................... 38
9.4 CD MECHANISM MODULE..................................................................................................................... 40
10. SCHEMATIC DIAGRAM............................................................................................................................... 42
10.1 TUNER AMP UNIT (GUIDE PAGE) ....................................................................................................... 42
10.2 KEYBOARD UNIT.................................................................................................................................. 48
10.3 CD CORE UNIT (S11.6STD) ................................................................................................................. 50
10.4 BT UNIT ................................................................................................................................................. 52
D 10.5 WAVEFORMS ........................................................................................................................................ 54
11. PCB CONNECTION DIAGRAM.................................................................................................................... 56
11.1 TUNER AMP UNIT................................................................................................................................. 56
11.2 KEYBOARD UNIT .................................................................................................................................. 60
11.3 CD CORE UNIT (S11.6STD).................................................................................................................. 62
11.4 BT UNIT ................................................................................................................................................. 64
12. ELECTRICAL PARTS LIST .......................................................................................................................... 65

FH-X700BT/XNUC
4
1 2 3 4
 5 6 7 8

1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A

1. You should conform to the regulations governing the product (safety, radio and noise, and other
regulations), and should keep the safety during servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside the unit.
3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the grating.
5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by
electrostatic induction. B

1.2 NOTES ON SOLDERING

D
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.

Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).

The following lead-free solders are available as service parts: E

Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

FH-X700BT/XNUC
5 6 7 8
5
 1 2 3 4

2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
FH-X700BT/XNUC

General WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

Power source ...................14.4 V DC (10.8 V to 15.1 V al- audio)
lowable) (Windows Media Player)
Grounding system ............Negative type WAV signal format ...........Linear PCM & MS ADPCM
Maximum current consumption (Non-compressed)
...................................10.0 A
Backup Current ...................4.0 mA or less USB
Dimensions (W × H × D): USB standard specification
D ................................... USB 2.0 full speed
Chassis .............. 178 mm × 100 mm × Maximum current supply
B 165 mm ................................... 1 A
(7 in.× 3-7/8 in.× 6-1/2 in.) USB Class ....................... MSC (Mass Storage Class)
Nose .................. 170 mm × 96 mm × File system ....................... FAT12, FAT16, FAT32
17 mm MP3 decoding format ......MPEG-1 & 2 Audio Layer 3
(6-3/4 in.× 3-3/4 in.× 5/8 in.) WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
Weight............................. 1.2 kg (2.6 lbs) audio)
(Windows Media Player)
Audio WAV signal format ...........Linear PCM & MS ADPCM
Maximum power output ... 50 W × 4 (Non-compressed)
70 W × 1/2 Ω (for subwoofer)
Continuous power output FM tuner
................................... 22 W × 4 (50 Hz to 15 000 Hz, Frequency range ..............87.9 MHz to 107.9 MHz
C 5 % THD, 4 Ω load, both chan- Usable sensitivity ............. 9 dBf (0.8 µV/75 Ω , mono, S/N:
nels driven) 30 dB)
Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable) Signal-to-noise ratio ......... 72 dB (IHF-A network)
Preout maximum output level
................................... 2.0 V
Loudness contour ............ +10 dB (100 Hz), +6.5 dB AM tuner
(10 kHz) (volume:–30 dB) Frequency range .............. 530 kHz to 1 710 kHz
Equalizer (5-Band Graphic Equalizer): Usable sensitivity ............. 25 µV (S/N: 20 dB)
Frequency ................. 80 Hz/250 Hz/800 Hz/ Signal-to-noise ratio ......... 62 dB (IHF-A network)
2.5 kHz/8 kHz
Equalization range .... ±12 dB (2 dB step)
Subwoofer (mono): Bluetooth
Frequency ................. 50 Hz/63 Hz/80 Hz/100 Hz/ Version ............................Bluetooth 3.0 certified
D 125 Hz/160 Hz/200 Hz Output power ................... +4 dBm Maximum
Slope ........................–6 dB/oct, –12 dB/oct (Power class 2)
Gain ......................... +6 dB to –24 dB
Phase .......................Normal/Reverse
CEA2006 Specifications

CD player
System ............................Compact disc audio system
Usable discs ....................Compact disc
Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)
Number of channels ........ 2 (stereo)
MP3 decoding format ......MPEG-1 & 2 Audio Layer 3
Power output ................... 14 W RMS × 4 Channels (4 Ω
and <= 1 % THD+N)
E S/N ratio .......................... 91 dBA (reference:1 W into
4 Ω)
Note
Specifications and the design are subject to
modifications without notice.

FH-X700BT/XNUC
6
1 2 3 4
 5 6 7 8

FH-X700BT/XNEW5

General WAV signal format ..................Linear PCM & MS ADPCM

A
Power source .............................14.4 V DC (10.8 V to 15.1 V (Non-compressed)
allowable)
Grounding system ...................Negative type USB
Maximum current consumption USB standard specification
.....................................................10.0 A .....................................................USB 2.0 full speed
Backup Current ............................4.0 mA or less Maximum current supply ....1 A
Dimensions (W × H × D): USB Class ...................................MSC (Mass Storage Class)
DIN File system ..................................FAT12, FAT16, FAT32
Chassis .....................178 mm × 100 mm × MP3 decoding format ...........MPEG-1 & 2 Audio Layer 3
157 mm WMA decoding format .........Ver. 7, 7.1, 8, 9, 10, 11, 12
Nose ...........................188 mm × 118 mm × (2 ch audio)
25 mm (Windows Media Player) B
D WAV signal format ..................Linear PCM & MS ADPCM
Chassis .....................178 mm × 100 mm × (Non-compressed)
165 mm
Nose ...........................170 mm × 96 mm × 17 mm FM tuner
Weight ..........................................1.2 kg Frequency range ......................87.5 MHz to 108.0 MHz
Usable sensitivity .....................9 dBf (0.8 µV/75 Ω , mono,
Audio S/N: 30 dB)
Maximum power output .......50 W × 4 Signal-to-noise ratio ...............72 dB (IEC-A network)
70 W × 1/2 Ω (for subwoo-
fer) MW tuner
Continuous power output ...22 W × 4 (50 Hz to Frequency range ......................531 kHz to 1 602 kHz
15 000 Hz, 5 % THD, Usable sensitivity .....................25 µV (S/N: 20 dB) C
4 Ω load, both channels dri- Signal-to-noise ratio ...............62 dB (IEC-A network)
ven)
Load impedance ......................4 Ω (4 Ω to 8 Ω allowable) LW tuner
Preout maximum output level Frequency range ......................153 kHz to 281 kHz
.....................................................2.0 V Usable sensitivity .....................28 µV (S/N: 20 dB)
Loudness contour ...................+10 dB (100 Hz), +6.5 dB Signal-to-noise ratio ...............62 dB (IEC-A network)
(10 kHz) (volume:–30 dB)
Equalizer (5-Band Graphic Equalizer): Bluetooth
Frequency ..........................80 Hz/250 Hz/800 Hz/ Version ..........................................Bluetooth 3.0 certified
2.5 kHz/8 kHz Output power ............................+4 dBm Maximum
Equalization range ........±12 dB (2 dB step) (Power class 2)
Subwoofer (mono): D
Frequency ..........................50 Hz/63 Hz/80 Hz/100 Hz/ Note
125 Hz/160 Hz/200 Hz Specifications and the design are subject to mod-
Slope ....................................–6 dB/oct, –12 dB/oct
ifications without notice.
Gain ......................................+6 dB to –24 dB
Phase ..................................Normal/Reverse

CD player
System ..........................................Compact disc audio system
Usable discs ..............................Compact disc
Signal-to-noise ratio ...............94 dB (1 kHz) (IEC-A net-
work)
Number of channels ..............2 (stereo) E
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12
(2 ch audio)
(Windows Media Player)

FH-X700BT/XNUC
5 6 7 8
7
 1 2 3 4

FH-X755BT/XNES and FH-X759BT/XNID

A
General USB
Rated power source .........14.4 V DC USB standard specification
(allowable voltage range: ................................... USB 2.0 full speed
12.0 V to 14.4 V DC) Maximum current supply
Grounding system ............Negative type ................................... 1 A
Maximum current consumption USB Class ....................... MSC (Mass Storage Class)
...................................10.0 A File system ....................... FAT12, FAT16, FAT32
Backup Current ..................4.0 mA or less MP3 decoding format ......MPEG-1 & 2 Audio Layer 3
Dimensions (W × H × D): WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch
DIN audio)
Chassis .............. 178 mm × 100 mm × (Windows Media Player)
157 mm WAV signal format ...........Linear PCM & MS ADPCM
B Nose .................. 188 mm × 118 mm × (Non-compressed)
25 mm
D
Chassis .............. 178 mm × 100 mm × FM tuner
165 mm Frequency range ..............87.5 MHz to 108.0 MHz
Nose .................. 170 mm × 96 mm × Usable sensitivity ............. 9 dBf (0.8 µV/75 Ω , mono, S/N:
17 mm 30 dB)
Weight ............................. 1.2 kg Signal-to-noise ratio ......... 72 dB (IEC-Anetwork)

Audio MW tuner
Maximum power output ... 50 W × 4 Frequency range .............. 531 kHz to 1 602 kHz (9 kHz)
C 70 W × 1/2 Ω (for subwoofer) 530 kHz to 1 640 kHz (10 kHz)
Continuous power output Usable sensitivity ............. 25 µV (S/N: 20 dB)
................................... 22 W × 4 (50 Hz to 15 000 Hz, Signal-to-noise ratio ......... 62 dB (IEC-Anetwork)
5 % THD, 4 Ω load, both chan-
nels driven)
SW tuner
Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable)
Frequency range .............. 2 300 kHz to 7 735 kHz
Preout maximum output level
(2 300 kHz to 2 495 kHz,
................................... 2.0 V
2 940 kHz to 4 215 kHz,
Loudness contour ............ +10 dB (100 Hz), +6.5 dB
4 540 kHz to 5 175 kHz,
(10 kHz) (volume:–30 dB)
5 820 kHz to 6 455 kHz,
Equalizer (5-Band Graphic Equalizer):
7 100 kHz to 7 735 kHz)
Frequency ................. 80 Hz/250 Hz/800 Hz/
D 9 500 kHz to 21 975 kHz
2.5 kHz/8 kHz
(9 500 kHz to 10 135 kHz,
Equalization range .... ±12 dB (2 dB step)
11 580 kHz to 12 215 kHz,
Subwoofer (mono):
13 570 kHz to 13 870 kHz,
Frequency ................. 50 Hz/63 Hz/80 Hz/100 Hz/
15 100 kHz to 15 735 kHz,
125 Hz/160 Hz/200 Hz
17 500 kHz to 17 985 kHz,
Slope ........................–6 dB/oct, –12 dB/oct
18 015 kHz to 18 135 kHz,
Gain ......................... +6 dB to –24 dB
21 340 kHz to 21 975 kHz)
Phase .......................Normal/Reverse
Usable sensitivity ............. 28 µV (S/N: 20 dB)
Signal-to-noise ratio ......... 62 dB (IEC-A network)
CD player
E System ............................Compact disc audio system
Bluetooth
Usable discs ....................Compact disc
Version ............................Bluetooth 3.0 certified
Signal-to-noise ratio ......... 94 dB (1 kHz) (IEC-A network)
Output power ................... +4 dBm Maximum
Number of channels ........ 2 (stereo)
(Power class 2)
MP3 decoding format ......MPEG-1 & 2 Audio Layer 3
WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch Note
audio)
(Windows Media Player) Specifications and the design are subject to
WAV signal format ...........Linear PCM & MS ADPCM modifications without notice.
(Non-compressed)

FH-X700BT/XNUC
8
1 2 3 4
 5 6 7 8

2.2 DISC/CONTENT FORMAT

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their respective owners.

FH-X700BT/XNUC
5 6 7 8
9
 1 2 3 4

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
A
To keep the product quality after servicing, please confirm following check points.

No. Procedures Item to be confirmed

1 Confirm whether the customer complain has The customer complain must not be
been solved. reappeared.
If the customer complain occurs with the Display, audio and operations must be
specific media, use it for the operation check. normal.
2 CD Play back a CD. No malfunction on display, audio and
(Track search) operation.
3 FM/AM tuner Check FM/AM tuner action. Display, audio and operations must be
B (Seek, Preset) normal.
Switch band to check both FM and AM.
4 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
5 Appearance check No scratches or dirt on its appearance after
receiving it for service.

See the table below for the items to be checked regarding audio:

Item to be checked regarding audio

Distortion
Noise
C
Volume too low
Volume too high
Volume fluctuating
Sound interrupted

3.2 PCB LOCATIONS

C CD Core Unit
D (S11.6STD)

B Keyboard Unit

A Tuner Amp Unit

D BT Unit
A:FH-X700BT/XNUC
B:FH-X700BT/XNEW5
C:FH-X755BT/XNES
D:FH-X759BT/XNID
Unit Number : QWM3544(A) Unit Number :
Unit Number : QWM3543(B) Unit Name : Keyboard Unit
Unit Number : QWM3545(C) Unit Number : QWM3533
F Unit Name : BT Unit
Unit Number : QWM3546(D)
Unit Name : Tuner Amp Unit Unit Number : CWX4023
Unit Name : CD Core Unit (S11.6STD)

FH-X700BT/XNUC
10
1 2 3 4
 5 6 7 8

3.3 JIGS LIST

- Jigs List A
Name Jig No. Remarks
16P FFC GGD1310 Tuner Amp Unit - CD Core Unit
Test Disc TCD-782 Checking the grating
L.P.F. Checking the grating (Two pieces)

- Grease List
Name Grease No. Remarks B
Grease GEM1024 CD Mechanism Module
Grease GEM1043 CD Mechanism Module

3.4 CLEANING

Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:

Portions to be cleaned Cleaning tools

CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
D

FH-X700BT/XNUC
5 6 7 8
11
 1 2 3 4

4. BLOCK DIAGRAM

A
A TUNER AMP UNIT

JA401
1 5
ANTENNA FMMIXIN1
57
16 DACOUTL
2,3 PINDIN
18
LNAIN
RF FRONT END IC
IC401 34 93
I2CSCL TUN_SCL
TDA7706 33 94
I2CSDA TUN_SDA
RSTN
31 88
TUNRES A :FH-X700BT/XNUC
B :FH-X700BT/XNEW5 EVO
JA892 C :FH-X755BT/XNES EVOL
3 KEYD 105 EVO
WIRED 2 KEYAD 56
KEYD D :FH-X759BT/XNID EVOL
KEYAD
REMOTE
B 1 GND EV
SYSTEM MICRO EV
Q531
COMPUTER
6 8 IC601 EV
VCC VDD3.3V (1/2)
5 MIC1P EVO
RMIC R5S726A0D216FP
4 MIC1N
iPod CP
IC531 25 39 1 RESET
CPPWR RES IC671
337S3959
S-80827CNMC-B8M
6 91
SCL CP_SCL
2 92
SDA CP_SDA

D
7 24
RST CPRST

BT UNIT ILMPW
Q871
B.UP ILM+B
CN21 CN23 CN971
FLASH ROM
MIC1N MIC1N MIC1N IC681
20 15 2 Q872
21
MIC1P MIC1P
13 4
MIC1P A :PEB040A8 19
ILMPW
22
MIC-BIAS B C D :PEB039A8
RESET NRST_CPU NRST_CPU 2
7 9 8 BTRST
C 11
BTTOSYS BTTOSYS
11 6
BTTOSYS 13
BTRX A
SYSTOBT SYSTOBT SYSTOBT 14
12 10 7 BTTX
BTDATA BTDATA BTDATA 7
13 5 12 BTDATA
BTSCK BTSCK BTBCK 4
BT MODULE

15 6 11 BT_BCK REGULATOR IC
BTLRCK BTRLCK BTLRCK 6 IC911
16 7 10 BT_LRCK
BA49183-V12
BT3.3V REG.
IC22 11 113
S-1206B33-U3 6 VDDCONT SWVDD
SW5V SW5V 1 90
BT3.3V 3 2 VCC VCC BSENS BSENS
8 VOUT VIN 1 16 9
SWVDD SWVDD 2 8
7 SYSPW SYSPW
2 15 VDD3.3V VDD 3
BT1.8V REG. 8 SW5VCNT
VDD1.2V VDD12
IC21 4 SYSTEM MIC
5
S-1172B18-E6 SYS+B SYS+B +B B.UP COMPUTE
BT1.8V 1 6 10 IC601
5 VOUT VIN +BUP
(2/2)
6 R5S726A0D2
BT18ON 3 ON/OFF
4

USB5V REGULATOR
IC551
D BD9876EFJ

C
8
B.UP VCC
PICKUP UNIT
(P10.6)(SERVICE) CD CORE UNIT(S11.6 STD)
5 118
SYNC SYNC
CN101 IC552
RF AMP, CD DECODER Q601
BD2232G-G
VCC 12 12 V+3A
DIGITAL SERVO/DATA • PROCESSOR 6 98
VDD EN DDON
CPU USB5V
5
VOUT VIN
1 1
LX
LD LD- GND 4
15 15 1
Q101 LD FB
7
BST
Q102
MD MD 5 PD 2
5 PD
V+3A VDD
REFO
VREF REFO 93 54 3 119
8 8 REFOUT EN USBCTL
PUEN 4 120
OC USBFLG
AC,BD,E,F
HOLOGRAM
UNIT IC201
PE5791A
FOM FOM CN701 CN701
3 3
ACTUATOR/
FOP FOP MOTOR DRIVER
E FOCUS ACT. 2 2
VDD
VDD
9 9
VDD
VDD3.3V
TOP 1 1 TOP
IC301
TRACKING ACT.
BD8223EFV
55
TOM 4 4 TOM TD,FD VDSENS
LD+ 14 LD+
MECHA VD
14 SD,MD
Q751 RGBDT/DI
8 VD VD
TKO+ VD 2 2 B.UP
7 RGBCS/IL
TKO- 1 1 Q752
10 RGBCK/IL
FCO+
9
FCO-
85
SOP 3 VDCONT
SPINDLE SPO+
MOTOR M SOM 2 CNT
23 40
CLCONT
SPO-
22 41
LDIN LOEJ
LCOP 5
LOADING/CARRIAGE SLLDO+ MUTE 21 39
CONT RESET 29 RESET
8 8
RESET 33
CDRST
MOTOR M LCOM 4
SLLDO-

38 CD DATA (CDSRQ,CDSTBY,SKIP, CD DATA (CDSRQ,CDSTBY,SKIP,

DSCSNS
SCL,SDA,DATA,BCLK,LRCK,WAIT) SCL,SDA,DATA,BCLK,LRCK,WAIT)
35
HOME
F
S903 S901
DSCSNS HOME

FH-X700BT/XNUC
12
1 2 3 4
 5 6 7 8

ELECTRONIC VOLUME/
SOURCE SELECTOR
IC201
PM9013A
JA251 RCA OUT
TUNL 40 35 PL PL 3
INAN1L OUTPL
RCAG 1
Q252
FL 6

RCAG 4

P251
81 19
EVOL_MCK MCLK
104 20 FL
EVOL_LRCK LRCLK
103 21
BCLK
JA901
EVOL_BCK Q251
22 FUSE 10A
106 18
EVOL_DATA DIN B.UP
110 23 17
EVOL_DT DATA
15 B.UP B
108 24
EVOL_CK CLK
111 25
EVOL_CS STB
87 26
EVOL_RST RESETB 33 11 9 FL+
OUTFL FLIn FL+ 1
34 12 7 FL-
OUTRL RLIn FL- 3
5 RL+
MUTE RL+ 5
Q301 3 RL-
RL- 7
(1/2)

AUXL 37 INBP4L AMP

IC301
PA2030A B.REM&A.ANT POWER
IC961 CONNECTOR
Q301
(2/2) TPD1052F
117 22 1 8 BREM
MUTE MUTE
B.UP VDD OUT 14

Q302 3
SYS+B IN

ANTPW
17 25
B.REM C

ASENS
Q941
89 ACC
ASENS 13

113
SWVDD
90
BSENS

B
8
SYSPW

KEYBOARD UNIT
SYSTEM MICRO
B.UP COMPUTER JA1921
CN801 CN1931 FRONT AUX
IC601 AUXR 3
(2/2)
R5S726A0D216FP AUXL AUXL AUXL 2
19 19
S1842 AUXGND 1
35 SOURCE SOURCE
SSENS 18 18
MULTI-CONTROL
S1830
53 ROT0 ROT0 2 5 KDT2
ROT0 6 6 D
54 ROT1 ROT1 1 4 KST1
ROT1 4 4
3 94 KDT0
P04
ILM+B 5 5 ILM+B 95 KDT1
118 P05
SYNC 96 KDT2
SWVDD 3 3 SWVDD P06
Q601 97 KDT3
P07
98 90 KST0 KEY MATRIX
DDON 22 KYDT KYDT 99 P00
KYDT 8 8 UTX/P34 LCD DRIVER/ 91 KST1
IC801 P01
KEY CONTROLLER 92 KST2
TC7SET08FUS1 IC1802 P02
23 2 4 DPDT DPDT 100 PDC202B 93 KST3
DPDT 10 10 URX/P35 P03

LCD
119 34 DSENS DSENS V1802
USBCTL DSENS 20 20
120
USBFLG ILM+B 98
RMIN/P73/INT/T0IN
REMOTE CONTROL
RGB DRIVER SENSOR
IC1851 Q1856
BH2228FV 1 IC1941
GP1UXC14RK

AO6
6 E
Q1855
55
VDSENS BLUE LCD

21 RGBDT RGBDT 12 5 GREEN LCD

RGBDT/DIMMER 7 7 DI AO5
Q1854
B.UP 15 RGBST/ILMCLR2 RGBST 10 RED LCD
RGBCS/ILMCLR2 14 14 CSB
11 RGBCK/ILMCLR1 RGBCK 11 BLUE Key
RGBCK/ILMCLR1 12 12 CLK
4
AO4 GREEN Key
Q1853
85 RED Key
VDCONT
Q1857, Q1858, Q1859,
3 Q1871 Q1870 Q1869 Q1866 Q1867 Q1868
AO3
Q1852
33
CDRST

2 D1882, D1885,
AO2 D1886
D1883,
Q1851
D1884,
D1887
1
AO1 F
CN1911
ILM+B ILM+B
USB5V USB5V
USB5V 11 11 2
49 DM DM DM
DM 13 13 3 USB
50 DP DP DP
DP 15 15 4

FH-X700BT/XNUC
5 6 7 8
13
 1 2 3 4

5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON

Vcc = 1.2 V Vcc : Pin 12, 20, 43, 78, 86, 109
PVcc = 3.3 V PVcc : Pin 3, 16, 28, 36, 48, 69, 82,101, 112

BSENS
B
Pin 90

BSENS = L

ASENS
Pin 89

ASENS = L

C
DSENS
Pin 34

DSENS = L

Starts
communication
with Grille
microcomputer.
D

300 ms
SWVDD <- H
Pin 113
300 ms

In case of the above signal, the communication

Source keys with Grille microcomputer may fail.
operative If the time interval is not 300 msec, the oscillator
may be defective.
E

Source ON

SYSPW <- H
Pin 8

F Completes power-on operation.

(After that, proceed to each source operation)

FH-X700BT/XNUC
14
1 2 3 4
 5 6 7 8

5.2 ERROR CODE LIST

ERROR CODES
If a CD memory device is inoperable, or operation of such media is stopped by an error, the error mode is established and a A
cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from
customers and facilitate failure analysis and repair work in servicing.

(1) DISPLAY METHOD

If “0xFD” error mode is displayed in CD MODE (CD MODE area for display), an error code will be displayed in the MIN (minute
display) and SEC (second display) areas.

The same code is displayed in the MIN and SEC areas.

The TNO area is blank (#0FFH), as it conventionally was.
• Display example of the head unit
Depending on the display capability of LCDs, the display format varies, as shown below. XX denotes an error number.
Note: In a case of an OEM product, the error display format is subject to the specifications used by the equipment B
manufacturer.
8-digit display 6-digit display 4-digit display
ERROR-xx ERR-xx E-xx

(2) LIST OF CD ERROR CODES (Error Mode: 0xFD)

Code Classification Error code to be displayed Details and possible causes
07 Servo TOC reading NG TOC information cannot be read.
--> The partial disk or TOC content is illegal. C

10 Servo Carriage Home NG The pickup cannot move toward the inner track.
The CRG cannot move from the inner track.
--> Defective HOME SW; Failure in CRG movement.
11 Servo Focus NG Focusing not available
--> Disc placed upside-down; Stains on the disc; excessive vibration.
12 Servo Spindle Lock NG Spindle not locked. Subcode not readable.
Subcode NG Proper RF AMP gain not obtained.
RF-amp NG --> Defective spindle; Scratches or stains on the disc; excessive vibration.
--> A CD-R/RW disc that does not contain data loaded, or in a rare case, disc placed upside-down.
--> RF signal error.
15 Servo RF NG The digital signal from the disc cannot be detected.
--> A CD-R/RW disc that does not contain data loaded.
D
17 Servo Setup NG The laser output cannot be adjusted. Focus can be easily lost.
--> Scratches or stains on the disc; excessive vibration.
30 Servo Search Time Out Failed to reach a target address. And, the search became a timeout.
--> Carriage/Tracking error; Scratches on the disc; Stains on the disc
50 Mechanism Load NG Disc loading/ejection not completed
Eject NG --> A foreign object inserted in the mechanism; Disc jammed.
51 Mechanism Failure in retried Disc could not be ejected even after disc turning had been retried.
turning for ejection --> A foreign object inserted in the mechanism; Disc jammed.

E
NOTES
• Indications of error codes are available only during disc operations, because CD operations are unavailable if a mechanical error is
generated.
• If the TOC cannot be read, It stops because of error 07.
• If you design a new head unit, be sure to use one of the display formats indicated in “Display example of the head unit.”
• The 2 high-order digits of an error code denote the main classification, shown below.
code classification
0x
1x Servo-related errors
3x
5x Mechanism-related errors

• How to restore from each error is shown below. F

Servo-related errors(0X, 1X, 3X) : Servo-related errors CD Off, Eject, ACC Off, Back-up Off, Communication reset, Reset
Load NG/Eject NG(50) : Reload, Eject, ACC Off, Back-up Off, Communication reset, Reset
Failure in retried turning for ejection : CD On, Eject, ACC Off, Back-up Off, Communication reset, Reset

FH-X700BT/XNUC
5 6 7 8
15
 1 2 3 4

USB storage device/iPod

Message Cause Action Message Cause Action
A
FORMAT Sometimes there Wait until the mes- CHECK USB The iPod oper- Make sure the con-
READ is a delay be- sage disappears ates correctly but nection cable for
tween the start of and you hear does not charge. the iPod has not
playback and sound. shorted out (e.g.,
when you start to not caught in
hear any sound. metal objects).
After checking,
NO AUDIO There are no Transfer the audio
turn the ignition
songs. files to the USB
switch OFF and
storage device and
back ON, or dis-
connect.
connect the iPod
The connected Follow the USB and reconnect.
B USB storage de- storage device in-
vice has security structions to dis- ERROR-19 Communication Perform one of the
enabled. able the security. failed. following opera-
tions.
SKIPPED The connected Play an audio file –Turn the ignition
USB storage de- not embedded with switch OFF and
vice contains Windows Media back ON.
files embedded DRM 9/10. –Disconnect the
with Windows USB storage de-
MediaTM DRM 9/ vice.
10. –Change to a dif-
PROTECT All the files in the Transfer audio files ferent source.
USB storage de- not embedded with Then, return to the
C USB source.
vice are em- Windows Media
bedded with DRM 9/10 to the iPod failure. Disconnect the
Windows Media USB storage de- cable from the
DRM 9/10. vice and connect. iPod. Once the
N/A USB The USB device • Connect a USB iPod’s main menu
connected to is Mass Storage is displayed, recon-
not supported by Class compliant nect the iPod and
this unit. device. reset it.
• Disconnect your ERROR-23 USB storage de- USB storage de-
device and replace vice was not for- vice should be for-
it with a compati- matted with matted with FAT12,
ble USB storage FAT12, FAT16 or FAT16 or FAT32.
D device. FAT32.
CHECK USB The USB connec- Check that the ERROR-16 The iPod firm- Update the iPod
tor or USB cable USB connector or ware version is version.
has short- USB cable is not old.
circuited. caught in some-
iPod failure. Disconnect the
thing or damaged.
cable from the
CHECK USB The connected Disconnect the iPod. Once the
USB storage de- USB storage de- iPod’s main menu
vice consumes vice and do not is displayed, recon-
more than maxi- use it. Turn the nect the iPod and
mum allowable ignition switch to reset it.
current. OFF, then to ACC
E STOP There are no Select a list that
or ON and then
songs in the cur- contains songs.
connect only com-
rent list.
pliant USB storage
devices. NOT FOUND No related Transfer songs to
songs. the iPod.

FH-X700BT/XNUC
16
1 2 3 4
 5 6 7 8

Bluetooth device Pandora

Message Cause Action Message Cause Action A

ERROR-10 The power failed Turn the ignition ERROR-19 Communication Disconnect the
for the switch OFF and failed. cable from the
Bluetooth mod- then to ACC or iPhone. Once the
ule of this unit. ON. iPhone’s main
If the error mes- menu is dis-
sage is still dis- played, reconnect
played after the iPhone and
performing the reset it.
above action, START UP The Pandora ap- Start up the
please contact APP plication has Pandora applica- B
your dealer or an not started run- tion from your
authorized ning yet. iPhone.
Pioneer Service
Station. INOPERABLE The operation Run the same
was disabled. command for an-
other track.
TRY AGAIN Communica- Try again later.
tions failed.
MAINTE- Pandora system Try again later.
NANCE is undergoing
maintenance. C

SKIP LIMIT Skip limit • Do not exceed

reached. the skip limit.
• Pandora limits
the number of
tracks you may
skip per station
and per day.
CHECK APP This version of Connect an
the Pandora ap- iPhone that has a
plication is not compatible ver- D
supported. sion of the
Pandora applica-
tion installed.
CHECK DE- Device error Please check your
VICE message dis- iPhone.
played in
Pandora Appli-
cation.
Unable to play
music from
E
Pandora.
NO STATION No station Create a station
found. in the Pandora
application on
your iPhone.
NO ACTIVE No station se- Select a station.
ST lected.

FH-X700BT/XNUC
5 6 7 8
17
 1 2 3 4

5.3 CONNECTOR FUNCTION DESCRIPTION

A MICROPHONE INPUT

ANTENNA WIRED FRONT

REMOTE OUTPUT
15 13 11 9 7 5 3 1 CONTROL
16 14 12 10 8 6 4 2

REAR OUTPUT or
1 FL+ 9 NC SUBWOOFER OUTPUT
D
2 FR+ 10 NC
3 FL- 11 NC
4 FR- 12 NC
5 RL+ 13 ACC
6 RR+ 14 B.REM
7 RL- 15 B.UP
8 RR- 16 GND

FH-X700BT/XNUC
18
1 2 3 4
 5 6 7 8

6. SERVICE MODE
6.1 DISPLAY TEST MODE 1
A
[How to enter Test mode]

Press and hold "PHONE" and "LIST" buttons together, and turn BUP and ACC on.

SOURCE LIST

PHONE

BAND ROTARY C

Grille condition
Conf. item Operate Show LCD RGB
All light up PHONE + LIST Draw 1 White
All light off SOURCE No light Draw2 No light
Conf. LCD pattern 1
(* And change ILM color) BAND Draw 3 Red
Conf. LCD pattern 2 ROTARY center Draw 4 Green
D

Drawings Style
Draw1 ALL light up
Draw2 ALL light off
Draw3

Draw4 E

FH-X700BT/XNUC
5 6 7 8
19
 1 2 3 4

6.2 DISPLAY TEST MODE 2

The information such as the system microcomputer version is checked.

A
[How to enter Test mode]
Press and hold "1" and "3" buttons together, and turn BUP and ACC on.

[Operation key]
Operation key Processing Remarks
Enter display test mode
1+3 Switch to next test mode

[Test items]
Start display test mode. Key Illumination Icon
Press and hold "1" and "3" buttons together, and turn * Initial
BUP and ACC on. Off All off condition

On (an initial value) All off

System Version information is displayed.

S $ $ $ $ # # #

$ PD number For PEA010A, "010A" is displayed

# System For Ver.7.01, "701" is displayed On (an initial value or
All off
microcomputer setting value of default
version menu)

Switching to next display

by pressing “ 1 ” + “ 3 ” buttons together.

Display is normally updated

Product operation is performed as usual, in appearance. On (an initial value or On (lighting condition
Switching to next display setting value of default of normal times)
by pressing “ 1 ” + “ 3 ” buttons together. menu)

E Display update is stopped

The screen gets still when entering this item. On (an initial value or On (state when
setting value of default entering test mode)
Switching to next display menu)
by pressing “ 1 ” + “ 3 ” buttons together.

FH-X700BT/XNUC
20
1 2 3 4
 5 6 7 8

6.3 SOFTWARE VERSION UP METHOD

Overview
This mode is used for upgrading the MCU software of system using USB memory. A

How to enter in USB rewriting mode

Press and hold "1" and "2" buttons together, and turn BUP and ACC on.

USB rewriting operation flow

Explanatory note
Screen display and ON/OFF of illumination

USB Characters displayed on the screen

Red frame: illumination lights up

Gray frame: illumination lights off
B
Blue characters: operation to be carried out by a user of USB rewriting function

Press and hold "1" and "2" buttons together, and turn BUP and ACC on.

START UPDT

Press LIST button

* After connecting USB memory in which upgrading file is stored, press LIST button.

(4) Retry count over Retry rewriting

As the reset is internally carried out,
display and illumination go out C
Check of upgrading file is started
(2) Upgrading file is not detected
Upgrading file error
CHECK FILE
First time After retry
Rewriting is started
If the power supply is turned OFF
during rewriting, retry the rewriting.
DON'T STOP

Switched every
5 seconds (3) Rewriting failed
D
PRG **/100

(1) Rewriting succeeded

CAN'T UPDT COMPLETE ERR->RETRY FILE ERROR ERR->RETRY

Display is continued until In 5 seconds, usual operation In 5 seconds, rewriting In 5 seconds, usual operation In 5 seconds, rewriting
the power supply is turned (OFF SOURCE) is retried (OFF SOURCE) is retried
OFF E
Result of rewriting
(1) Rewriting succeeded Displayed when USB rewriting is normally terminated.
In 5 seconds, usual operation (OFF SOURCE) is started.
(2) Upgrading file error Displayed when there is no upgrading file in USB memory or the data of upgrading file is different.
Upgrading file is not detected In 5 seconds, usual operation (OFF SOURCE) is started.
If the upgrading file error is detected or the upgrading file is not detected after the rewriting is retried, the rewriting is failed.
In 5 seconds, rewriting is retried.
(3) Rewriting failed Displayed when the writing of upgrading file in serial Flash is not normally terminated.
Or, displayed if the upgrading file error is detected or the upgrading file is not detected after the rewriting is retried.
In 5 seconds, rewriting is retried.
(4) Retry count over Displayed when the retry becomes unavailable because the retry count is exceeded.
The display is continued until the power supply is turned OFF. If the power supply is turned ON again, the display is not changed.
The upgrading using USB is disabled, so it is necessary to write programs in serial Flash using E10A.
F

FH-X700BT/XNUC
5 6 7 8
21
 1 2 3 4

6.4 CD TEST MODE

A - Flow Chart
[4]+[6]->BUP+ACC ON [CD] or [SOURCE] [Key]
Test Mode IN Source ON
Contents
TRK MIN
Display

[BAND] [2]
Power On RF AMP *1
(T.Offset is adjusted) Gain switching
TRK MIN SEC TRK MIN SEC
00 00 00 GG GG GG

[BAND] [3] [6] [1] [RIGHT] [LEFT] [2]

Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
B S curve check *2 Close *6 *6 switching *3
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??

[BAND] [1] [3] [RIGHT] [LEFT] [2]

Power Off T.Close & AGC RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [RIGHT] [LEFT] [2]

Power Off F,T,RF AGC*5 F,T AGC / F.Bias CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

C *6

[BAND] [2]
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X

or 9X 9X 9X

Operation
*1) TYP t + 6 dB t + 12 dB [Key] Test Mode
TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [BAND] Power On/Off
[RIGHT] CRG + / TR Jump +
(Direction of the external surface)
D *2) Focus Close t S. Curve t F EQ measurement setting [LEFT] CRG - / TR Jump -
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 (Direction of the internal surface)
(TRK99MIN99SEC99) [1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
[2] RF Gain switching / Offset adjustment display /
*3) F.Offset Display t RF.Offset t T.Offset Display t Switch to the order T.Balance adjustment / T. Open
of the original
[3] F. Close,S. Curve / Rough Servo and RF AGC /
display
F,T,RF AGC
*4) 100TR Jump [6] F. Mode switching / Tracking Close

*5) TRK/MIN/SEC t F.AGC t T.AGC Gain t F.Bias t RF AGC

E

*6) CRG motor voltage = 2 [V]

After the [EJECT] key is pressed keys other than the [EJECT] key should not be pressed, until disc ejection is complete.
When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens sticks
to Wall, causing the actuator to be damaged).
In the case of 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the
F default setting.
Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows)

FH-X700BT/XNUC
22
1 2 3 4
 5 6 7 8

7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
A

Removing the Grille Assy (Fig.1)

Grille Assy
1 1
1 Release the nine latches and then remove
the Grille Assy.
1 1

1 1 B

1 1 1

Fig.1

Removing the Keyboard Unit (Fig.2) C

Keyboard Unit
1 Remove the seven screws and then 1
remove the Keyboard Unit. 1

1
1 1

D
1 1

Fig.2

Removing the Tuner Amp Unit and the BT Unit (1/2) (Fig.3)

1 Disconnect the Connector.

E

Fig.3

FH-X700BT/XNUC
5 6 7 8
23
 1 2 3 4

Removing the Tuner Amp Unit and the BT Unit (2/2) (Fig.4)
A
The CD Mechanism Module side is made a bottom.

1 Remove the screw. 2 2

2 Remove the two screws. 1

CD Mechanism Module

hook Tuner Amp Unit and BT Unit

3 Push the area and remove the two hooks.
(Left side and Right side)
4
4 Slide the Tuner Amp Unit and the BT Unit
in the direction of the arrow and then remove
the Tuner Amp Unit and the BT Unit. 3
C

CD Mechanism Module
D

5 Disconnect the Connector.

6 Remove the screw and then remove the 8

BT Unit.

7 Remove the two screws.

E
8 Remove the two screws and then remove
the Tuner Amp Unit. 5

8
6 7 7

BT Unit Tuner Amp Unit

F
Fig.4

FH-X700BT/XNUC
24
1 2 3 4
 5 6 7 8

Attention of removing (Fig.5)

Don’t remove this screws excluding the dismantlement A

of the CD Mechanism Module.

CD Mechanism Module

Fig.5 C

FH-X700BT/XNUC
5 6 7 8
25
 1 2 3 4

How to carry the mecha unit

1. Hold the designated points (shown with dashed lines) of the upper chassis and the front/rear bracket.
A 2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion.
3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less)

Handling OK

Handling NG

FH-X700BT/XNUC
26
1 2 3 4
 5 6 7 8

How to remove the PU unit

1. Create an empty-clamp state according to “How to create empty clamp state (motor drive)”.
2. Hook the feeding screw biasing spring to a tentative hooking portion (Fig 2b). Be careful not to get injured by the A
spring edge.
3. Hold the PU at the position A as shown in Fig 1. Slide the PU as far as possible toward the holder in the feeding screw
so that a joint on the outer end of the feeding screw is loosened.
4. As shown in Fig 3, move the rear end of the feeding screw laterally and then upward, to remove it from the outer holder.
5. Lift the PU unit to disengage it from Part B of the chassis (Fig 4), and remove the PU unit.
(Cautions) When re-installing the PU, be sure to first nip the chassis and the PU unit (Fig 4) at the position B.
Also, make sure to fully hook the feeding screw biasing spring (Fig 2a).
Please follow the service manual for adjustment of the PU unit after the re-installation.

Slide toward inner circumference

Fig 2a Fig 2b
B
Fig 1

Fully-hooked state Tentatively-hooked state

C
The spring is below a resin
flange and is built inside the
B A sheet metal bending.

Fig 3 Fig 4

[Incorrect built-in state]

The chassis is not nipped between
Outer holder Normal built-in state
the PU case and the PU rack.
Rear end of feeding screw

FH-X700BT/XNUC
5 6 7 8
27
 1 2 3 4

8. EACH SETTING AND ADJUSTMENT

8.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode

In this product the single voltage (3.3 V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65 V) To enter the test mode.
instead of the GND. [4] + [6] -> Reset
If you should mistakenly short the REFO1 with the GND
during adjustment, accurate voltage will not be obtained, To exit from the test mode.
and the servo’s misoperation will apply excessive shock Turn off the ACC and back up.
to the pickup. To avoid such problems:
a. Do not mix up the REFO1 with the GND when Notes:
connecting the (-) probe of measuring instruments. a. During ejection, do not press any other keys than the
B Especially on an oscilloscope, avoid connecting the (-) EJECT key until the loaded disc is ejected.
probe for CH1 to the GND. b. If you have pressed the [RIGHT] key or [LEFT] key during
b. In many cases, measuring instruments have the same focus search, turn off the power immediately to protect
potential as that for the (-) probe. Be sure to set the the actuator from damage caused by the lens stuck.
measuring instruments to the floating state. c. For the TR jump modes except 100TR, the track jump
c. If you have mistakenly connected the REFO1 to the GND, operation will continue even if the key is released.
turn off the regulator or the power immediately. d. For the CRG move and 100TR jump modes, the tracking
loop will be closed at the same time when the key is
Before mounting and removing filters or leads for released.
adjustment, be sure to turn off the regulator. e. When the power is turned off and on, the jump mode
is reset to the single TR (91), the RF amp gain is set to 0 dB,
For stable circuit operation, keep the mechanism and the auto-adjustment values are reset to the default
C
operating for about one minute or more after the settings.
regulator is turned on.

In the test mode, any software protections will not

work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

The RFAGC and RFO signals with a wide frequency range

are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

D
The load and eject operation is not guarantied with the
mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

FH-X700BT/XNUC
28
1 2 3 4
 5 6 7 8

8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE
CD CORE UNIT

F L.P.F.

E Xch Ych
E 100 kohm
Oscilloscope
VREF 390 pF

F 100 kohm

REFO1 390 pF
VREF
D
L.P.F.

Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the RIGHT and LEFT buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking
balance adjustment the display should now read "81". Press key 3. The display will change,
returning to "81" on the fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase E
difference is within 75 . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

FH-X700BT/XNUC
5 6 7 8
29
 1 2 3 4

Grating waveform Ech -> Xch 20 mV/div, AC

Fch -> Ych 20 mV/div, AC
A

0 degrees 30 degrees

45 degrees 60 degrees

75 degrees 90 degrees

FH-X700BT/XNUC
30
1 2 3 4
 5 6 7 8

8.3 PCL OUTPUT CONFIRMATION

A
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TESTIN IC601(Pin 99) terminal to H.
The clock signal is output from the PCL terminal IC601(Pin115).
The frequency of the clock signal is 600 kHz that is divided by 20th of the oscillation frequency of X601 (12 MHz).
The clock signal should be 600 kHz(- 25 Hz, + 25 Hz).
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

FH-X700BT/XNUC
5 6 7 8
31
 1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
"
Screw adjacent to mark on the product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
9.1 PACKING
Tape

X700BT/XNEW5
X700BT/XNEW5
X755BT/XNES
B

X700BT/XNUC X755BT/XNES
X759BT/XNID
X700BT/XNUC
X755BT/XNES
X759BT/XNID
X700BT/XNUC
X755BT/XNES
X759BT/XNID
F

X700BT/XNEW5

FH-X700BT/XNUC
32
1 2 3 4
 5 6 7 8

(1) PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Cord Assy See Contrast table (2) 12 Card Remote Control Unit See Contrast table (2)
2 Polyethylene Bag See Contrast table (2) 13 Handle See Contrast table (2)
A
3 Screw See Contrast table (2) 14 IM CD-ROM See Contrast table (2)
4 Screw See Contrast table (2) 15-1 Owner's Manual See Contrast table (2)
5 Cover See Contrast table (2)
* 15-2 Warranty Card See Contrast table (2)
6 Microphone Assy CPM1083 * 15-3 Caution Card See Contrast table (2)
7 Holder CZN7192 * 15-4 Caution Card See Contrast table (2)
8 Cushion CZN7193 15-5 Quick Start Guide See Contrast table (2)
9 Unit Box See Contrast table (2) 15-6 Installation Manual See Contrast table (2)
10 Contain Box See Contrast table (2)
* 15-7 Caution Card See Contrast table (2)
11 Protector See Contrast table (2) * 15-8 Service Network See Contrast table (2) B

(2) CONTRAST TABLE

FH-X700BT/XNUC, FH-X700BT/XNEW5, FH-X755BT/XNES and FH-X759BT/XNID are constructed the same
except for the following:
Mark No. Description FH-X700BT/XNUC FH-X700BT/XNEW5 FH-X755BT/XNES FH-X759BT/XNID
1 Cord Assy CDP1480 QDP3014 CDP1480 CDP1480
2 Polyethylene Bag CEG1160 Not used CEG1160 CEG1160
3 Screw CRZ50P090FTC Not used Not used Not used
4 Screw TRZ50P080FTC Not used TRZ50P080FTC TRZ50P080FTC
5 Cover CEG1359 CEG1356 CEG1356 CEG1356
C
9 Unit Box QHG3416 QHG3415 QHG3417 QHG3418
10 Contain Box QHL3416 QHL3415 QHL3417 QHL3418
11 Protector QHP3033 QHP3032 QHP3032 QHP3033
12 Card Remote Control Unit QXE1044 Not used QXE1044 QXE1044
13 Handle Not used CND6289 CND6289 Not used

14 IM CD-ROM Not used QPJ3017 Not used Not used

15-1 Owner's Manual QRD3136 Not used QRD3137 QRB3256
* 15-2 Warranty Card QRY3001 CRY1376 Not used CRY1304
* 15-3 Caution Card Not used CRP1438 Not used Not used
* 15-4 Caution Card Not used CRP1441 Not used Not used
D
15-5 Quick Start Guide Not used QRD3146 Not used Not used
15-6 Installation Manual Not used QRD3147 Not used Not used
* 15-7 Caution Card Not used QRP3015 Not used Not used
* 15-8 Service Network Not used Not used Not used CRY1305
Owner's Manual,Installation Manual
Part No. Language

QRD3136 English, French, Spanish(Espanol)

QRD3146 English, French, Italian, Spanish(Espanol), German, Dutch, Russian

QRD3147 English, French, Italian, Spanish(Espanol), German, Dutch, Russian

E
QRD3137 English, Spanish(Espanol), Portuguese(B), Traditional Chinese, Arabic, Persian

QRB3256 English

FH-X700BT/XNUC
5 6 7 8
33
 1 2 3 4

CONTENTS OF CD-ROM (Operation Manual), QPJ3017

Part No. Language
* QRB3281 English
A * QRB3282 French
* QRB3283 Italian
* QRB3284 Spanish(Espanol)
* QRB3285 German
* QRB3286 Dutch
* QRB3287 Russian
* QRB3288 Swedish
* QRB3289 Norwegian
* QRB3290 Finnish
* QRB3291 Danish
B * QRB3292 Portuguese
* QRB3293 Greek
* QRB3294 Turkish

All operation manuals are supplied in PDF files by the CD-ROM.

Regarding the availability of paper manual, contact Pioneer Service representative in your region.

FH-X700BT/XNUC
34
1 2 3 4
5 6 7 8

FH-X700BT/XNUC
5 6 7 8
35
 1 2 3 4

9.2 EXTERIOR(1)

X759BT/XNID

X700BT/XNEW5
X755BT/XNES
X700BT/XNEW5
X755BT/XNES

FH-X700BT/XNUC
36
1 2 3 4
 5 6 7 8

(1) EXTERIOR(1) SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Screw BSZ26P060FTC 14 Segment LCD (V1802) CAW2025

2 CD Mechanism Module (S11.6STD-FH) CXK5806 15 Holder QNC3047
A
3 FFC QDE3029
4 Grille Assy See Contrast table (2) 16 Sheet QNM3068
5 Screw BPZ20P080FTC 17 Rubber Connector QNV3053
18 Lighting Conductor QNV3054
6 Button (<, >) QAC3089 19 Knob Unit QXA3723
7 Button (PHONE, 1-6, DISP) QAC3090 20 Spring YBL5010
8 Button (EJECT) QAC3093
9 Cover QNM3029 21 Grille Unit See Contrast table (2)
10 Sheet QNM3066 22 .....
23 Holder See Contrast table (2)
11 Sheet QNM3067 24 Panel See Contrast table (2) B
12 Sheet QNM3071 25 Label See Contrast table (2)
13 Lighting Conductor QNV3061

(2) CONTRAST TABLE

FH-X700BT/XNUC, FH-X700BT/XNEW5, FH-X755BT/XNES and FH-X759BT/XNID are constructed the same
except for the following:
Mark No. Description FH-X700BT/XNUC FH-X700BT/XNEW5 FH-X755BT/XNES FH-X759BT/XNID
4 Grille Assy QXA3817 QXA3816 QXA3818 QXA3819
21 Grille Unit QXA3809 QXA3721 QXA3810 QXA3811
23 Holder Not used CND6288 CND6288 Not used
24 Panel Not used CNS9952 CNS9952 Not used C

25 Label Not used Not used Not used CNN3533

FH-X700BT/XNUC
5 6 7 8
37
 1 2 3 4

9.3 EXTERIOR(2)

X700BT/XNEW5
A
X700BT/XNUC
X755BT/XNES
X759BT/XNID

B
X700BT/XNUC
X755BT/XNES
X759BT/XNID

A
C

B B

FH-X700BT/XNUC
38
1 2 3 4
 5 6 7 8

(1) EXTERIOR(2) SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Cord Assy See Contrast table (2) 12 BT Module CWX4317

2 Screw ASZ26P050FTC 13 Tuner Amp Unit See Contrast table (2)
A
3 Screw BSZ26P060FTC 14 Screw BPZ26P080FTC
4 Screw BSZ26P080FTC 15 Screw BSZ26P060FTC
5 Screw BSZ26P120FTC
16 Screw BSZ26P120FTC
6 FFC QDE3028 17 Holder QNC3053
7 Case QNB3006 18 Heat Sink See Contrast table (2)
8 Holder QNC3057 > 19 Fuse (10 A) YEK5001
9 Bracket QNC3058 20 Card Remote Control Unit See Contrast table (2)
10 Bracket QNC3059
21 Cover See Contrast table (2)
11 BT Unit QWM3533 B

(2) CONTRAST TABLE

FH-X700BT/XNUC, FH-X700BT/XNEW5, FH-X755BT/XNES and FH-X759BT/XNID are constructed the same
except for the following:
Mark No. Description FH-X700BT/XNUC FH-X700BT/XNEW5 FH-X755BT/XNES FH-X759BT/XNID
1 Cord Assy CDP1480 QDP3014 CDP1480 CDP1480
13 Tuner Amp Unit QWM3544 QWM3543 QWM3545 QWM3546
18 Heat Sink QNR3010 QNR3010 QNR3002 QNR3002
20 Card Remote Control Unit QXE1044 Not used QXE1044 QXE1044
21 Cover CNS7068 Not used CNS7068 CNS7068
C

FH-X700BT/XNUC
5 6 7 8
39
 1 2 3 4

9.4 CD MECHANISM MODULE

A
B
(A)

(B)
B

(A) (B)

C
(A)

(A)

C B C
(A)
D
(A)
(A)

(A)
(B)

(A)

(B)

(A) C

(A) : GEM1024
F (A)
(B) : GEM1043

FH-X700BT/XNUC
40
1 2 3 4
 5 6 7 8

CD MECHANISM MODULE SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 ..... 50 Damper CNW1198

2 Screw BSZ20P040FTC A
3 Screw(M2 x 4) CBA1835 51 Arm CNW1726
4 Washer CBF1038 52 Motor Unit(M2)(LOAD/CRG) CXC4026
5 Spring CBH3010 53 Screw Unit CXC8894
54 Arm Assy CXE6232
6 Spring CBH2855 55 Washer CBF1037
7 Spring CBH2856
8 Spring CBH2860 56 Washer CBF1038
9 Screw BSZ26P060FTC 57 Arm CND6242
10 Spring CBH3011 58 Collar CNW2444
59 Roller CNW2500
11 Coil Spring CBH3095 60 Gear Unit CXC8893 B
12 Spring CBH3014
13 Spring CBH3015 61 Washer YE15FTC
14 Spring CBH3016 62 Chassis Unit CXE4528
15 Spring CBH3017 63 Motor Unit(M1)(SPDL) CXE2273
64 Screw JFZ20P025FTC
16 Spring CBH3086 65 Screw JGZ17P022FTC
17 Spring CBH3019
18 ..... 66 Screw EBA1028
19 Leaf Spring CBL1824 67 CD Core Unit (S11.6STD) CWX4023
20 Pickup Unit(P10.6)(Service) CXX3556 68 Case CNB3762
C

21 Bracket CND4553
22 Arm CND6406
23 Bracket CND6127
24 Bracket CND5710
25 Lever CND5398

26 Sheet CNN3678
27 Rack CNV8342
28 Guide CNW2240
29 Roller CNW1172 D
30 .....

31 Arm CNW2241
32 Roller CNW1175
33 .....
34 Arm CNW1177
35 Arm CNW1178

36 Gear CNW1180
37 Gear CNW1181
38 ..... E
39 Gear CNW1183
40 Rack CNW1184

41 Gear CNW1185
42 Gear CNW1186
43 Gear CNW1187
44 Gear CNW2287
45 Clamper CNW1190

46 Arm CNW1192
F
47 Holder CNW1193
48 Holder CNW1194
49 Damper CNW1197

FH-X700BT/XNUC
5 6 7 8
41
 1 2 3 4

10. SCHEMATIC DIAGRAM

10.1 TUNER AMP UNIT (GUIDE PAGE)
A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".

A-a A-b
Large size
SCH diagram
A-a
C457
C456
4700p/25
4700p/25
TUNR
TUNL FM/AM(A, C, D): -15.0 dBs
CD C CN701
TUNER

8 RESET
CN701

11 DATA
GND
FM/AM(B): -11.0 dBs

6 SKIP

9 VDD
7 SDA
5 SCL
VD
VD
AGND VKN1192-A

CTF1756-A

9p/50
JA401

C449
36.48MHz

10
1
2
3
4
CTF1786-A

C450

9p/50
L420
TUNGND YKS5041-A X401
*1 AGND

HSPC16701B02

L419
2 1 MECHA VD

C445 0.1u/10
X2

C448 0.1u/10

CCG1218-A
2.2u
4 GND2 3

C446 NM

RESET

DGND1
3 DGND 7.4V

SKIP
KN2

DATA
SCL
CDSRQ

CDSTBY

VDD4
SDA
P402

P401

NM

0.1u/10
1 2

C453
VD2

C447
M2R6TP_GND GND1 R416 NM Q751
A-a X1

1u/10
A-b

C452
Guide page C455 CSS1848-A *1
2SD2396(K) VD1

C753 CCG1192-A
0.22u/16 R701

10u/10
L418 NM A B C, D

R753
L417 NM 47k

47k

C751 NM
L405 NM R702

R417
C454 68n NM

NM
54 0.1u/10
RFGND

55 C451
L406 CTF1389-A CTF1389-A NM 100k

R752
NM

820
L416 NM L407 NM NM 0.27uH
R415 0
*1 L408 4.7uH 1.5uH VDCONT Q752

64
63
62

PLLTEST 61
GND-PLL 60

59
58
57
56

53
OSCIN 52
51
VDDPLL1V2 50
49
L415 4.7uH
L414

TVDAC
L409 NM 0.39uH

TCFM
NM

OSCOUT
DACOUTR

VDDIO1V2
R401

R402

NM

VCC-REF
VCC-PLL

DACOUTL

VREFDEC
1 48 3 4
220

750

GND-ADC_DAC

GND-REF
VCC-ADC_DAC
CTF1786-A
A-a Detailed page L410 47uH 47uH 2.2uH

0.1u/10
A-b

R754
C444 2 5 GND

10k
2 47
L414 NM CTF1786-A NM

RKZ8.2KG(B2)
CCG1218-A 2.2u 1 6
KP2311E

KP2311E

3 46 R403 390 390 R703

330
D401

D402

FMMIXDEC TEST C443 RN4983 5 4

RFGND C401

D751
NM 4 VDD_CORE 45 R408 470 470 360
NM

150
C752
FMMIXIN2

150
L401 6 3

B
C410 5 GND1V2 44 R409 NM NM 0
C402
FMMIXIN1 FMPINDRV GPIO0 7 2
33p/50 0.27uH 0.01u/16 6 43 R411 680 680 390
FMPINDDEC GPIO1
0.01u/16
0.01u/16

0.01u/16

GNDRF

R715
R415 0 NM 0 8 1
6p/50
C409

C408

C407

C406

C405

C403 GPIO2
NM

7 42
L402
0.15u

TCAM GPIO3 C419 NM NM 15p/50

220
220
100
220
100
1u/10 8 41 4.7k
C420 NM 0.01u/16 0.01u/16 GND

1k
AGND VCCRF IC401 GPIO4
orRFGND C404 NM 9 40 C421 3p/50 NM NM
CK_SEL TDA7706 GPIO5

R711
10 39 C423 NM NM 8p/50 R704 100k
RF GND GNDVCO GPIO6
L403 11 38 C428 100p/50 100p/50 22p/50

R706
R707
R708
R709
R710
C412 LFREF GPIO7 C702
C430 DCH1246-A NM NM
0.1u/10

CTF1786-A 0.1u/10 C411 12 37 R705

C413

LF1 GPIO8 C432 82p/50 82p/50 2p/50 NM

L701

NM
0.01u/16 13 PINDDEC 36 C701 NM
A GND VCCVCO GND3V3 C433 DCH1246-A NM NM
C414 0.01u/16 PINDIN C442

VREG3V3
14 TCAM2 35

VCCREG1V2
L404 C436 NM NM 0.1u/10 0.01u/16 C703

RDSINT
VDD3V3

GNDSLINK
AMMIXIN1
AMMIXIN2
CTF1786-ARFGND
LNAOUT2
LNADEC2
C415 15 0.1u/10

RSTN
34 C439 NM
GNDLNA

TUN_SCL NM 0.1u/16
LNADEC

LNAOUT

REG1V2
I2CSCL
LNAIN2

NM
DGND
LNAIN

C441 10p/50 NM NM GND

I2CSDA 33
0.1u/10

CCG1192-A

VDIG
C461

16 TUN_SDA
0.1u/10
C417

C416
NM

RFGND 10u NM CCG1218-A

C447

CTF1786-A
NM

L413
C418
0.022u/16 C448 0.1u/10 0.1u/10 NM
17
18
19
20
21
22
23
NM 24

25
26
27
28
29
30
31
32
GND
RFGND C419 15p/50 R403 390 C424
C420
0.1u/10

R409 0
C427

R410 0

TUN_RST
C426

L406
0.1u/10

0.01u/16 L408 0.01u/16 B.UP

*1
C460

CTF1389-A 4.7uH C425 GND

CCG1192-A SW5V
R404

1000p/50
1M

0.1u/16
L405

NM
0.1u/10

C438
10u C437

C440
L407
NM
68n
C436

C439
3.3V
0.39uH 8p/50

R407
L409 C423

0.27uH C430 1u
1M

33

CDDATAIN
C422
NM

VDCONT
VDSENS
DCH1246-A

CDSTBY

CD_SDA
CDSKIP
CDSRQ

CDRST
RFGND
R408 470

*1 DGND 1/4W 1/4W

100p/50

C431 NM
*1
R406

C428
3p/50

R412 R413
C421

*1

10p/50
8.2 8.2
DGND C441

VDCONT

MCLK
R405

BSENS
ASENS
FLASH ROM

RESETB

CDWAIT
NM

TUN_RST
L411 NM
*2
82p/50
R411 680
C432

0.47u/10
C435

C429 L410
NM
C434

R414 0

R681
IC681

R684
IC681 *2

47k
RF GND

47k
0.01u/16 47uH 1u
RF GND C433 C458 C459 1 8
A PEB040A8 CS VCC
NM 2 NC/SIO3 7
*1 RFGND DCH1246-A NM
B, C, D PEB039A8 SO/SIO1

NM
DGND AGND RF GND DGND AGND
3 SCLK 6
WP/SIO2

R682
4 5

47k
GND SI/SIO0

C682
KN1
C CN971 BT Connector
M2R6TP_GND
VKN1192-A

0.1u/10
C625

22p/50
VCC 16

C622
R638

47k
NM
C971

VCC 15
GND 14 C973
GND 13 R974
47p/50 100

C623 0.1u/10
BTDATA R636
BTDATA 12

47k

C621 0.1u/10
R632
R975 100 BT_BCK

100
100
100
100

100

100

100
47k
BTBCK 11

C620
R635 1k
R634 1k

0.1u/10
47k
R976 100 BT_LRCK R637

C624
0.1u/10
BTLRCK 10
D L971

R633

R631

R630

R629
R628
R627
R626

R625
GND 9 47k
NM
BT_RST
NRST_CPU 8
CN23 SYSTOBT 7
R971 NM
BTTX
BTRX

90
89
88
87
86
85
84
83
82
81
80

MD_CLK 79
78
77
76
75
74
73
72
71
70
69
68
R640

R639
BTTOSYS 6

4.7k

4.7k

VDCONT
TUNRES

QSPCLK
MD_BOOT
C972

QSSL
QIO1
Vss
R972
NM

EVOL_MCK
91

QIO3

QIO2

QIO0
NM

Vss

Vcc
5

PVcc
/ASENS
GND CP_SCL

AUDIO_X1
Vcc

Vss
PVcc
/BSENS

EVOL_RST

/CDWAIT
MIC1P 4 CP_SDA 92
R641 93
GND 3 GND TUN_SCL
R973 R642
MIC1N 2 TUN_SDA NM 94 CP_SCL
0 CP_SDA
GND 1 CD_SCL NM 95
TUN_SCL
MIC1P
MIC1N

GND CD_SDA 96 TUN_SDA

GND
CDSRQ 97 CD_SCL
CD_SDA
JA892 TESTIN 98

R668 47k
/CDSRQ
R669

47k

YKS5035-A R643 99 DDON

6 MIC1P DDON TESTIN
(RMIC) 5 100k 100
MIC1N Vss
4 C626
3 LTC014YEB 101 PVcc
2 Q601
1 KEYD BT_TESTMD 0.1u/10 102 BT_TESTMD
VA892 NM

(W/R) C627 22p/50

1000p/50

1000p/50

JA891 1 R891 KEYD2

VA891

1k R644 100
C894

KEYD 103
NM

IC601
C893

3 BCLK EVOL_BCK
NM
R893

KEYAD KEYAD2 KEYAD

NM 2 LRCLK R645 100 104 EVOL_LRCK
R892 R5S726A0D216FP
0.1u/16

1k
0.1u/16
C891

C892

C628 22p/50
NM

105 KEYD
R646

W.REM
D602

GND
10k

106

D
EVOL_DATA
W.REM&MIC KEYD 107 Vss
DIN R647 100
GND CLK 108 EVOL_CK
Q531 R648 1k
22p/50

C629
C631

L531 LSAR523UB 109 Vcc

NM DATA R649 1k 0.1u/10 110 EVOL_DT
R536 4.7k CPPWR STB R650 1k 111
EVOL_CS
0.1u/10
R531

R540
47k
C531

C630 112 PVcc

R533

R532
2.2k

2.2k

47k CP_SCL
R537 100 SWVDD5 0.1u/10 113 SWVDD
R539 CP_SDA 114 Vss
R538 100 PCL 115 PCL
R651 47k

47k RAM_MON
CPRST RAM_MON 116 MUTE
SYNC
R534 2.7k

RGBDT/DIMMER
IC531

RGBCK/ILMCLR1
USBCTL

RGBCS/ILMCLR2
MUTE 117
B.UP
CCG1222-A 4.7u

USB5V
3.3V

337S3959 /USBFLG
L551 USB&USB5V C553 D551 R652 SYNC 118
1 8 CTH1524-A 0.01u/16 SYNC
BT_TESTIN

BT_LRCK
220u/16

CMS03 2.2k 119

C552

1u/16
C551

GND PAD VCC USBCTL

BTDATA
R535 4.7k

4 BT_BCK

SYSPW

2 7
C564 CCG1201-A

ANTPW
C565

BTRST

ILMPW
9

DPDT
BTRX

KYDT
120

BTTX

PVcc
SDA RST FLG
ROM
3 PVcc

IC551

Vss
220u/6.3

3 6
Vss

Vcc
Vss
NM

Vcc
RB056L-40
R552

BD9876EFJ
1u/10

R661

NC1 SCL
0

4.7u

NM

4 5
NM
D552
470
0.1u/10

R653
C532

6800p/25

1 8
1
2

6
7
8
9
C555

10
11
12
13
14
15
16
17
18
19
20
21
22
23
NC2 NC3 Lx VCC GND
C558

LX VCC
R553 TP1

2 7 10k
C554

GND 9
C633

BST
C557
C556

NM
R555

GND BST
180k D

ROM

GND 3 6 DDON BTTESTIN

VC EN
R603 47k
R551

0.1u/10

VC FIN EN
C603 0.1u/10

R664 10k
6.8k

4 5 SYNC
FB SYNC
R601

C604

0.1u/10
C601

R602
0.1u/10
47k

FB SYNC
47k
NM
C563

iPod CP @(2.0C)
43k D

C602
R554

GND
GND GND
RGBDT

IC552
R662

GND 1 5
NM

VIN VOUT DGND

2
GND FLG
C561

1u/10

R663

3 4 FLG
C562

NM
NM

EN OC
1u/10
C560

C559

USBCLT
NM

BD2232G-G USBCTL
RGBST/ILMCLR2

E
RGBCK/ILMCLR1

RGBDT/DIMMER

GND
SYSPW
BTDATA
BT_LRCK
BT_BCK
BT_RST

OFFSET

ILMPW

DPDT
BTRX

KYDT
BTTX
DSENS
RGBDT/DIMMER
VBUS

CN801
R802

2.2k

CKS6452-A C801

NM
20
NOTE : DSENS R801 2.2k R805 100
AUXL 19 GND 22k
Symbol indicates a resistor. 18
R803
R806 100
SOURCE
No differentiation is made between chip resistors and A FH-X700BT/XNUC AUXR 17 R804 22k R807 100
16 L801
discrete resistors. B FH-X700BT/XNEW5
AUXGND 11
DP 15
Symbol indicates a capacitor.
C FH-X755BT/XNES RGBST/ILMCLR2 14
No differentiation is made between chip capacitors and DM 13
44

discrete capacitors. D FH-X759BT/XNID RGBCK/ILMCLR1 12

CTF1713-

B USB5V

DPDT
11
10
US5V

The > mark found on some component parts indicates

CN1931 USBGND 9
NM
R818

KYDT 8
the importance of the safety factor of the part. RGBDT 7
6
Therefore, when replacing, be sure to use parts of ROT0
ILM+B 5
identical designation. 4
ROT1
SWVDD 3
D803 DZ2S068C

D804 DZ2S068C

F
D805 DZ2S068C

D806 DZ2S068C

D807 DZ2S068C

ILMGND 2 DGND
C802 NM

NM

NM
NM
D801

NM
NM

0.1u/16

ILMG
NM : No Mount
1u/10

C803
NM
NM

NM

DGND 1
NM
D808 NM

D809 NM

USGND C804
C805

C807
C806
D802

NM
VA801

VA802
C808

D810

D811

GRILLE

A
DGND USBGND ILM GND

FH-X700BT/XNUC
42
1 2 3 4
 5 6 7 8

A-b
C CN701
C707
NM
ROL
PL

RL
8 RESET

15 PGND

01
11 DATA

13 LRCK

A
FL
12 BCLK

16 WAIT
GND
6 SKIP

14 GND
9 VDD
7 SDA

TUNER AMP UNIT

5 SCL
VD
VD

C708
2-A
NM FM/AM(A, C, D): -6.0 dBs
10
1
2
3
4

C236

C212 CCG1192-A
A GND FM/AM(B): -2.0 dBs

0.1u/10
0.1u/10
0.1u/10
1u/10
AUX:+10.2 dBs

NM
CD/USB:+10.2 dBs

10u
DGND C221
RESET

DGND1

PGND
SKIP

DATA
SCL
CDSRQ

CDSTBY

VDD4
SDA

BCLK

C231
LRCK

C204 1u/10
WAIT

NM

C213
C214
C215
PGND DGND C206 1u/10
AGND DGND REFERENCE AREA MAP
R718

R701
220

C233 EVOL 201 - 250 MECHA VD 751 - 800

31 150p/50
47k C202 1u/10

29 C211
R702 RCA 251 - 300 GRILL 801 - 850
R719 NM
100k
100k
AMP 301 - 400 SWVDD5 851 - 870
40
39
38
37
36
35
34
33
32

30

28
27
26
25
24
23
22
21
C223 TUNER 401 - 460 ILMPW 871 - 890

OUTRL
OUTPL

AGNDL1
AGNDL2
INAN1L

INBN3L

IN5L

OUTFL
INAP2L

INBP4L

VREFL
AVDDL1
AVDDL2
DVDD2

DATA
STB
CLK
RESETB

BCLK
DIN
1000p/50 iPod CP 531 - 550 W.REM&MIC 891 - 900
PM9013A

12 AGNDR1
13 AGNDR2
9 AVDDR1
10 AVDDR2
IC201

USB&USB5V 551 - 600 PW CONNECT 901 - 910

1 INAN1R

3 INBN3R
2 INAP2R

4 INBP4R

OUTRR
6 OUTPR

OUTFR

11 VREFR

17 DVDD1

20 LRCLK
14 DGND

18 DOUT
C235 19 MCLK
GND

15 TEST
5 IN5R

16 REG
AGND DGND UCOM 601 - 670 IC REG 911 - 940
R703 FM/AM(A, C, D): -6.0 dBs
4 RESET 671 - 680 ASENS 941 - 950 FM/AM(B): -2.0 dBs Set back chart
7
8

CTF1793-A
FLASH ROM 681 - 690 TELIN 951 - 960
150

AUX:+10.2 dBs
150
150

3 L201
DSENS 691 - 700 B.REM& 961 - 970 CD/USB:+10.2 dBs B

NM
2 NM

10u
L202

CCG1192-A

C224 0.1u/10
A.ANT RL FL

C218 47u/16

NM
C704 CD MECHA 701 - 750
R716
R715

1
R717

BT MOD 971 - 990

RCA RR FR

CCG1192-A
10p/50
C210
220
220
100
220
100

4.7k

CCG1192-A

C225
0.1u/10
C705

C217

C220
1k

150p/50

C216

10u
C256 R256

10u
10p/50 PLch

C219
R711

R704 100k C706 ucomD RFGND CCG1201-A 820

DGND 4.7u
1u/10

>
1u/10

GND MUTE
R706
R707
R708
R709
R710

NM

10p/50
1u/10

C702

100p/50
R258

C258
22k
NM

1000p/50
CCG1192-A

R705
C232

C229

C228 3.0A
10u C209
C226

NM
C207 0.1u/10
C208 0.1u/10

NM
NM
L701

1
2
3
NM

NM P251

RN1910
RCAG
C201

Q252
CEK1386-A
C234

C203
C205

C703 1 2
PL JA251

6
5
4
NM C227 R259

100p/50
R257

C257
GND CKB1099-A

22k
NM AGND NM
USBGND AGND USB GND FR C255 PR

PREOUT
PRch CCG1201-A R255 GND
ROR 3
RR 4.7u 820
PR FL 2
FLch C252 R252 1
6
CCG1201-A 820
4.7u FR 5
4

100p/50
R254

C254
22k
CDDATAIN

CDLRCKIN

1
2
3
CDSCKIN

RN1910
CDSTBY

CD_SDA

RESETB
CDWAIT

Q251
CDSKIP
CDSRQ

CDRST

LRCLK

*5
AUXG

TUNR

AUXR

MCLK

DATA
AUXL

TUNL

BCLK

CLK
STB
DIN

6
5
4

100p/50
R253

C253

C259

NM

1000p/50
22k

C260

C261
NM
FLASH ROM L681 C251 R251
FRch
NM
R681

IC681 CCG1201-A
R684

820
*2
47k

47k

R685

*5
47k

4.7u GND
1 8
0.1u/10

CS VCC X602 GND

2 NC/SIO3 7 NM C261
SO/SIO1 IC301
NM

16.9344MHz X603
3 SCLK 6 GND1 A, C 100p/50 PA2030A
WP/SIO2 1 3 X1
C683 3p/50

GNDTP1
R682

4 5 2 1 B, D 1000p/50 1
47k

C681

GND SI/SIO0 TAB

C682

C619 GND2 C618

R683

2
AMP
47k

C
2 P-GND2
12p/50 3 X2 4 12p/50 3
CSS1794-A RL-
SYS+B 5.78 V R309 STBY 4
R624 16.9344MHz STBY
10k 5

C328
NM
22p/50

1608
DGND 2.2k RL+
6
R301

R311
470

R303

C329
VCC

NM

47k
470

L601 VDD3.3V
7
FL-
NM C317 8
10u/16
R304

R621 P-GND1
C617

470
C616

100p/50
NM

NM

R302
8
7
6
5

9
470

C319
AGND GND FL+
R623
47k

C621 0.1u/10

NM
ASEBRK 47k

C318 GND
R622

10 SVR
100
100
100
100

100

100
47k

47k
C620
0.1u/10

GND C301 0.22u/16 NM 11

TMS 2
TDI 3
TDO 4
TCK 1

FLIn
R631

R630

R629
R628
R627
R626

R625

TRST

C305 0.22u/16 12
VDD1.2V RLIn
L602
13

C320

1p/50
AGND
NM C307 0.22u/16 GND 14
R620
*3 RRIn
C614

C615
NM

NM

C303 0.22u/16 AGND

MD_CLK 79
78
77
76
75
74
73
72
71
70
69
68

67
66
65
64
63
ASEBRK 62

TRST 61

NM 15
C613 R618 R619 FRIn
AC_GND
TDO
TCK

C313
TMS

16
QSPCLK
MD_BOOT

QSSL

0.1u/10
QIO1
Vss

TDI

C309 NM

C310 NM

C311 NM

C312 NM
QIO3

QIO2

QIO0
Vcc

PVcc

60
AUDIO_X1

C331 NM

C332 NM

C333 NM

C334 NM
A 10k 47k AC-GND
Vss

*3
AUDIO_X2

R619

1u/16 17
47k

59 C612
B 47k 22k

100p/50
FR+

C321
0.1u/10 R618 GND GND 18
58
D601

C 22k 47k C314 0.1u/16 P-GND3

NM

R617

AVref
10k

AVcc 57 MODEL 47k 19

D 47k 47k FR-
AVss GND C901 20
56 AGND KEYAD B.UP
MODELAD VCC
MU1 CCH2040-A 21
KEYAD 55 VDSENS RR+
R305 GND 2200u/16
R616 47k R306 22
VDSENS 54 MUTE
ROT1 GNDTP2
ROT1 10k 1k 23 RR-
53 R615 47k ROT0
ROT0
24 P-GND4
CDSKIP 52 CDSKIP
1u/16

Q301
C335
R307

C327

ASEMDR614
NM

25
NM

ASEMD 51 3 4 B.REM
Q302

C323

C324

C325

C326
47k GND R312
DP 50 DP MUTE 2 5 LTC014YEB 10k
DM 49 DM 1 6

10p/50
SW5V

IC601

10p/50

10p/50

10p/50
PVcc 48 RN4983
R659

R660

B.UP

SYS+B
15k

15k

3.3V

1.2V
0.1u/10
C611

R5S726A0D216FP Vss 47
Vss 46 GND MUTE GND
PVcc

XTAL 45 R613 C608 OFFSET

D
GND GND
R612 1.5k
EXTAL 44 12p/50

Vcc 43
NM C610 JA901
X2 3

NC1 2

CKM1613-A
0.1u/10
>
NMI 42 47k
CSS1847-A

IC REGULATOR IC911 18
12MHz

PLLVcc 41 R611
X601

BA49183-V12 600uH GND1 GND2 (10A) FUSE

C609 0.1u/10 BSENS 17
Vss 40 BSENS 1 BSENS L901 D901 B.UP3 B.UP1
NC2

YEK5001
16 GND
1 X1

SYSPW SYSPW 2 SYSPW 2 1

RES 39 1SR154-400
CTH1432-A 15 B.UP
4

Vss 38 C607 3 SW5VCNT D902 BREM&A.ANT

+B 14 BREM&A.ANT
CKIO 37 4 +B ACC
12p/50 1SR154-400 GND
PVcc 13 ACC
C606 SYSB
R610

5 SYS+B

POWER SUPPLY
R609

36
47k

SSENS
47k

SW5V 12
/DSENS 35 0.1u/10 USB GND SSENS 6 SW5V
/CDRST 11
RGBDT/DIMMER

DSENS1 R608
RGBCK/ILMCLR1

VDD
RGBCS/ILMCLR2

CDDADATIN 34 DSENS 7 VDD

TELIN 10
CDLRCKIN 33 NM CDRST 1.2V 8 VDD12
R607 NM 9 TEL
SWVDD 9 SWVDD
CDSCKIN

32 CDDATAIN RR2
CDSTBY
CPPWR
ANTPW

ILMPW

CPRST

R606 NM B.UP2 8 RR-

TELIN
DPDT
BTRX

KYDT

10 +BUP
BTTX

PVcc

RL2
PVcc

31 CDLRCKIN
Vss

Vss
Vcc

7
Vcc

SWVDD5 VDDCNT 11 VDDCONT RL-

RR1
RST IC671 6
RL1 RR+
12 GND
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

1 5 5
OUT NC2 FR2 RL+
C929

NM

2 D911
C925

NM

4 FR-
SWVDD

VDD CRG03
SYS+B

FL2
R603 47k

D671
0.1u/10

3 4
C603 0.1u/10

R664 10k

R604 NM

3 FL-
TELIN1

R912

VSS NC1 D912 FR1

C605
0.1u/10
C604

C916 R911
0.1u/10

NM 2 FR+
C928

R671 FL1
CCG1201-A
CCG1201-A

CCG1201-A

CCG1201-A

CCG1201-A

S-80827CNMC-B8M CRG03
1000p/50

1
1000u/16

FL+
C602

100k
1000p/50

C914

1000p/50
C913
1000p/50

0.1u/16
NM

C915

C912
C927

C926

C922

C920

C919

C918

C911
C924

C921
C923

NM
NM

C917
NM

NM

NM

RESET
C671

C930
NM

1u/10
C672
RGBDT

NM
RFGND GND
FM/AM(A, C, D):+20.0 dBs
4.7u

4.7u

4.7u

4.7u

4.7u

RFGND FM/AM(B):+24.0 dBs

DGND
NM

ASENS GND AUX:+36.2 dBs

CD/USB:+36.2 dBs
*4
R605

ASENS
LSCR523UB

ASENS2 ASENS1
R941 D941 R944
Q941

RGB Supply
RGBST/ILMCLR2

E
RGBCK/ILMCLR1

RGBDT/DIMMER

Q871 22k 1k
HZU7L(A1)
2SA1577(QR)
R943

4.7k
R942

C941

0.1u/16
47k
CDSCKIN
CDSTBY
OFFSET

ILMPW

CPPWR

R872
CPRST
DPDT
BTRX

KYDT
BTTX

10k
TELIN

*4 D941 R943 GND

R871

3.3k
(1/10W)

A, C, D HZU7L(A1) 4.7k
B HZU7L(C3) 47k R952
NM
Q872
22k
Q951
TELIN
LTC143EUB LSAR523UB
R808 2.2k SSENS D951
R953 L951
GND
R805 100 AUXL R951 15k BTH1101-A
R803 22k
R806 100
R877 NM Q873
2SD1767(QR)
LED Supply TELIN
GND
1SS301
AUXR 1k
1
R804 22k R807 100 AUXG
R873
NM

R879
1.2k

L801 R809 Q874

11 2 2 DP DCH1256-A
0.1u/16

3 4 C969
D871
47k

22
0.1u/16

RKZ7.5KG(B2)

2 5 22u
C872

NM

NM

IC961
NM

R810 GND GND

44 3 3 DM 1 6
R878
C873

R874

RN4983 1 VDD 8 D302

390

CTF1713-A 22 R811 2.2k RGBST/ILMCLR2 ILMPW OUT

2 NC1 7
C871

R812 CRG03
CRG03

2.2k RGBCK/ILMCLR1 NC2

R876

D872

D301

C322
0.1u/16

R961 3 IN 6
R813 2.2k RGBDT/DIMMER DIAG
R875
47k

10k 4 GND 5
MASK C330
R962 10k

Dim off 12.13 V

C963 NM

1M

0.1u/16

R814 2.2k KYDT Q875

0.033u/16
NM

Dim on 8.03 V NM
TPD1052F
0.1u/16

DPDT LTC043EEB
C962

C966

C961
R815
8.2k

R963

ILM GND
C965

R816 2.2k AGND GND

ROT0
ILMPW B.REM&A.ANT
R817 2.2k A GND GND
ROT1
SWVDD
L851 IC801

F
D806 DZ2S068C

D807 DZ2S068C

NM

NM

NM 1 5
NM
0.1u/16

C852

DPDT
NM
NM

NM

INB Vcc
NM

R851

2
4.7k

C851

NM
D808 NM

D809 NM

INA
3 4
C810
C809

GND OUTY
VA801

VA802
C808

0.1u/10
C811
D810

D811

TC7SET08FUS1
GND
GND SWVDD

A
GND

FH-X700BT/XNUC
5 6 7 8
43
 F
E
B
A

D
C

44
A-a A-b
A-b
CN701 PL
C707 ROL RL
NM
FL
C708

GND

1
1

VDD
NM
TUNER AMP UNIT

8 RESET
9
FM/AM(A, C, D): -6.0 dBs

10
11 DATA
12 BCLK
13 LRCK
14 GND
15 PGND
16 WAIT
C236
A GND FM/AM(B): -2.0 dBs
A
1u/10
AUX:+10.2 dBs
DGND CD/USB:+10.2 dBs C221

NM
0.1u/10
0.1u/10
0.1u/10

10u
C204 1u/10
NM

DATA
PGND
C231

VDD4
BCLK
PGND DGND

DGND1
LRCK
WAIT
C206 1u/10

C212 CCG1192-A
C213
C214
C215
AGND DGND REFERENCE AREA MAP

220
EVOL 201 - 250 MECHA VD 751 - 800

R718
C202 1u/10 C233

R719 NM
RCA 251 - 300 GRILL 801 - 850
100k
AMP 301 - 400 SWVDD5 851 - 870

40
39
38
37
36
35
34
33
32
31 150p/50
30
29 C211
28
27
26
25
24
23
22
21
C223 TUNER 401 - 460 ILMPW 871 - 890
1000p/50 iPod CP 531 - 550 W.REM&MIC 891 - 900

STB
CLK
DIN

IN5L
DATA
BCLK

OUTPL
OUTRL
OUTFL
VREFL
DVDD2

INAN1L
INAP2L
INBN3L
INBP4L
USB&USB5V 551 - 600 PW CONNECT 901 - 910

AGNDL1
AGNDL2
AVDDL1
AVDDL2
RESETB
GND

IC201
AGND DGND UCOM 601 - 670 IC REG 911 - 940

PM9013A
INAN1R
INAP2R
INBN3R
INBP4R
IN5R
OUTPR
OUTRR
OUTFR
AVDDR1
AVDDR2
VREFR
AGNDR1
AGNDR2
DGND
TEST
REG
DVDD1
DOUT
MCLK
LRCLK
FM/AM(A, C, D): -6.0 dBs
RESET 671 - 680 ASENS 941 - 950

1
2
3
4
5
6
7
8
9
FM/AM(B): -2.0 dBs Set back chart

10
11
12
13
14
15
16
17
18
19
20
L201 FLASH ROM 681 - 690 TELIN 951 - 960 AUX:+10.2 dBs

150
150
150
NM DSENS 691 - 700 B.REM& 961 - 970 CD/USB:+10.2 dBs

NM
10u
A.ANT RL FL

C235
C704

L202
CD MECHA 701 - 750

NM

CTF1793-A
BT MOD 971 - 990

R716
10p/50 RR FR

R715
R717
RCA
C705

CCG1192-A

C210
C225

C224 0.1u/10
C218 47u/16
C256 R256

C217
C220
10p/50 PLch

C216

2
2

0.1u/10
10u

10u
CCG1192-A

150p/50
C706 CCG1201-A 820

C219
ucomD

CCG1192-A
RFGND
DGND
GND 4.7u MUTE
C702 10p/50

NM
1u/10
1u/10
>
22k

NM

1u/10
R258
C258

NM 1 3.0A
2
3

NM

NM
100p/50

P251

C232
C229
C228

C209

NM
C226
RCAG

L701
CEK1386-A

1000p/50
2

C201
C703 1
Q252

C234
C203
CCG1192-A

C205
10u
RN1910

6
5
4

PL
NM C227 R259 JA251

C207 0.1u/10
C208 0.1u/10
GND NM AGND NM CKB1099-A
22k

R257
C257

USBGND AGND USB GND FR C255 PR

100p/50

PRch CCG1201-A R255 GND

ROR 3
RR 4.7u 820
PR FL 2
FLch C252 R252 1
6
CCG1201-A 820
4.7u FR 5
4
PREOUT

1
2
3
22k

R254
C254

FH-X700BT/XNUC
100p/50

Q251

*5
RN1910

6
5
4

CDDATAIN
CDSCKIN
CDLRCKIN
CDWAIT
AUXL
AUXG
TUNL
TUNR
AUXR
MCLK
LRCLK
BCLK
DIN
DATA
CLK
STB
RESETB
NM

22k

R253
C253
C259
NM
C260
C261

ROM
100p/50

L681 FRch C251 R251

1000p/50

NM
CCG1201-A 820

3
3

4.7u GND

47k
8 *5

R685
VCC X602 GND
SIO3 7 NM C261
16.9344MHz X603 IC301

0.1u/10
SCLK 6 GND1 A, C 100p/50 PA2030A
1 3 X1 GNDTP1
5 2 1 B, D 1000p/50 1
/SIO0 TAB
C619

C681
GND2 C618 2
2 P-GND2

47k
AMP

R683
3 X2 4 12p/50 3

C683 3p/50
12p/50
CSS1794-A RL-
SYS+B 5.78 V R309 STBY 4
R624 16.9344MHz STBY
10k 5
2.2k RL+
NM

DGND
C328
1608

6
VDD3.3V
470 VCC
NM

L601
47k

R301
470

7
R311

R303
C329

FL-
NM C317 8
R621 10u/16 P-GND1

8
7
6
5
470

NM
9

NM
R304

AGND GND FL+

C617

C616
470

R302

NM GND
C319

C318
100p/50

10 SVR

R623

100
47k
R622
C301 0.22u/16 NM 11

C620
GND FLIn

0.1u/10
C305 0.22u/16 12

TDI 3

TCK 1
TMS 2
TDO 4
VDD1.2V RLIn
L602

R625
TRST

ASEBRK 47k
13
AGND
NM C307 0.22u/16 GND
C320

14
1p/50

R620 RRIn
*3 C303 0.22u/16 AGND

NM
NM

70
69
68
67
66
65
64
63
NM 15

C614
C615
C613 R618 R619 FRIn
C313 AC_GND 16
60 0.1u/10
A 10k 47k AC-GND
NM
NM
NM

TCK
TDI
TDO

TMS

Vss

4
TRST 61
*3
4

1u/16

PVcc
59 C612 17
FR+

47k
B 47k 22k

R619

ASEBRK 62

QSPCLK
0.1u/10 R618 GND GND 18
58
C309 NM

C314 0.1u/16 P-GND3

C310
C311
C312
C331 NM
C332 NM
C333 NM
C334 NM

AUDIO_X1
AVref C 22k 47k

AUDIO_X2
C321
100p/50

NM
MODEL 47k 19

D601
10k
AVcc 57 FR-

R617
D 47k 47k C901
AVss GND B.UP 20
56 AGND KEYAD VCC
MODELAD
VDSENS MU1 CCH2040-A 21
KEYAD 55 RR+
R305 R306 GND 2200u/16 22
VDSENS 54 R616 47k MUTE
ROT1 GNDTP2
ROT1 10k 1k
53 R615 47k ROT0 23 RR-
ROT0
CDSKIP 24 P-GND4
CDSKIP 52
ASEMDR614 Q301 25
3 4 B.REM
NM

ASEMD 51
NM

1u/16
C335

R307
C327

Q302 GND R312

47k DP MUTE 2 5
DP 50 LTC014YEB 10k
C323
C324
C325
C326

DM 49 DM 1 6
PVcc 48 RN4983
15k
15k

R659
R660
SW5V
B.UP

47
10p/50

3.3V
1.2V

Vss
10p/50
10p/50
10p/50

.1u/10

C611
SYS+B

MUTE
 56 AGND KEYAD GND B.UP 20
MODELAD VCC
VDSENS MU1 CCH2040-A 21
KEYAD 55 RR+
R305 GND 2200u/16
R616 47k R306 22
VDSENS 54 MUTE
ROT1 GNDTP2
ROT1 10k 1k
53 R615 47k ROT0 23 RR-
ROT0
CDSKIP 24 P-GND4
CDSKIP 52
ASEMDR614 Q301 25
3 4 B.REM

NM
ASEMD 51

NM

1u/16

R307
C335

C327
Q302 GND R312
47k DP MUTE 2 5
DP 50 LTC014YEB 10k

C323
C324
C325
C326
DM 49 DM 1 6
PVcc 48 RN4983

15k
15k

R659
R660
SW5V
B.UP
47

10p/50

3.3V
1.2V
Vss

10p/50
10p/50
10p/50

C611
SYS+B

0.1u/10
Vss 46 GND MUTE GND
XTAL 45 R613 C608 OFFSET GND

PVcc
GND
R612 1.5k
EXTAL 44 12p/50
NM C610 JA901
Vcc 43 CKM1613-A
5

5
0.1u/10

X2 3
NMI 42 47k

NC1 2
IC REGULATOR IC911 18 >
PLLVcc 41 R611 GND1 GND2 (10A)
BSENS BA49183-V12 600uH 17 FUSE
C609 0.1u/10

X601
Vss 40 BSENS 1 BSENS L901 D901 B.UP3 B.UP1 YEK5001

12MHz
CSS1847-A
SYSPW 2 1 16 GND

NC2
RES 39 SYSPW 2 SYSPW 1SR154-400
CTH1432-A 15 B.UP

4
1 X1
Vss 38 C607 3 SW5VCNT D902 BREM&A.ANT
+B 14 BREM&A.ANT
CKIO 37 ACC
12p/50 4 +B 1SR154-400 GND
PVcc 13 ACC
C606 SYSB
SSENS 36 5 SYS+B

47k
12

47k
R610
SW5V

R609
/DSENS 35 0.1u/10 USB GND SSENS 6 SW5V
/CDRST DSENS1 R608 11
34 DSENS VDD
CDDADATIN 7 VDD
TELIN
CDLRCKIN 1.2V 10
33 NM CDRST 8 VDD12
R607 NM 9 TEL
32 CDDATAIN SWVDD 9 SWVDD RR2
R606 NM B.UP2 8 RR-
31 CDLRCKIN 10 +BUP RL2

RGBDT/DIMMER
VDDCNT 7 RL-

PVcc
Vss

KYDT
DPDT
CPRST
CPPWR
TELIN
CDSTBY
SWVDD5

CDSCKIN

Vcc
11 VDDCONT RR1
RST IC671 6
RL1 RR+

21
22
23
24
25
26
27
28
29
30
12 GND
1 5 5
OUT NC2 FR2 RL+
2 D911

NM
4 FR-

C929
VDD CRG03

NM
FL2

C925
D671 3 4 3
VSS NC1 D912 FL-
FR1
POWER SUPPLY

1
1

SWVDD
SYS+B
NM 2

R912
FR+

C605
R671 FL1

TELIN1
S-80827CNMC-B8M CRG03

0.1u/10

0.1u/10
1

R604 NM
C928
100k FL+

NM
NM

C930

NM

NM
C914

NM
NM
C913
RESET

C915
C912

NM
C927
C926
C922
C920
C919
C918
C916 R911
C911

C924
C921

C923
C917
1000p/50

0.1u/16

C671
1000u/16

6
6

C672
1u/10
1000p/50
1000p/50

CCG1201-A

CCG1201-A
CCG1201-A
CCG1201-A
1000p/50
CCG1201-A
NM
RFGND GND
FM/AM(A, C, D):+20.0 dBs
RFGND

RGBDT
FM/AM(B):+24.0 dBs

4.7u
4.7u
4.7u
4.7u
4.7u
DGND GND
ASENS AUX:+36.2 dBs

NM
CD/USB:+36.2 dBs
*4 ASENS

R605
ASENS2 ASENS1
R941 D941 R944
RGB Supply

Q941
Q871 22k 1k
HZU7L(A1)
2SA1577(QR)

LSCR523UB
4.7k

47k
R943

R942
C941
0.1u/16

10k

R872

KYDT
DPDT

RGBDT/DIMMER
CPRST
CPPWR
TELIN
CDSTBY
CDSCKIN
*4 D941 R943 GND
A, C, D HZU7L(A1) 4.7k

R871
3.3k
(1/10W)
B HZU7L(C3) 47k R952

22k
NM
Q872 TELIN
Q951

FH-X700BT/XNUC
LTC143EUB LSAR523UB
R808 2.2k SSENS D951
R953 L951
GND
AUXL R951 15k BTH1101-A
R877 Q873 LED Supply TELIN
NM 2SD1767(QR) 1SS301
GND

7
7

AUXR 1k
1
AUXG

NM
1.2k
Q874

R873
L801 R809

R879
1 2 2 DP DCH1256-A
3 4 C969
22

47k
D871
2 5 22u

0.1u/16
IC961

NM
NM
4 R810 DM GND GND

C872
NM
3 3 1 6 D302

0.1u/16
R811 RGBST/ILMCLR2 RN4983 ILMPW 1 VDD 8
22 2.2k

R878
CTF1713-A OUT

C873
390
R874
R812 2 NC1 7 CRG03
2.2k RGBCK/ILMCLR1 NC2

RKZ7.5KG(B2)
R961

C871
3 IN 6
RGBDT/DIMMER

R876
D872
D301

R813 2.2k
C322

DIAG
CRG03

4 GND 5

47k
10k
0.1u/16

R875
MASK C330
Dim off 12.13 V
R814 2.2k Q875
1M

KYDT Dim on 8.03 V NM

NM

DPDT LTC043EEB TPD1052F

0.1u/16

ILM GND
R962 10k
C963 NM
C962
C966
C961

GND

8.2k
AGND

R815
0.1u/16

R816 2.2k
0.033u/16

ROT0
R963

C965

ILMPW B.REM&A.ANT
R817 2.2k A GND GND
ROT1
SWVDD
L851 IC801
NM 1 5

NM
DPDT

NM
INB Vcc

NM

NM
NM
NM
2

C852
INA

NM

4.7k
R851
3 4

C851
GND OUTY

C810
C809
8

8
C811

TC7SET08FUS1

D811
VA801
VA802
0.1u/10

GND
GND SWVDD
GND

A-a A-b
A-b

45
E
A

D
C

F
B
 F
E
B
A

D
C

46
A-a A-b
A-b

A-a
C457 4700p/25 TUNR CN701
C456 4700p/25
CD C
TUNL FM/AM(A, C, D): -15.0 dBs
TUNER FM/AM(B): -11.0 dBs CN701

VD
VD
GND
VKN1192-A

1
1

SDA
VDD
AGND

1
2
3
4
5 SCL
6 SKIP
7
8 RESET
9
10
11 DATA
12 BCLK
13 LRCK
14 GND
15 PGND
16 WAIT

JA401 36.48MHz

9p/50
*1 AGND

C449
TUNGND YKS5041-A X401

L420
C450
9p/50
2 1 X2 MECHA VD

L419
CTF1756-A
4 GND2 3

2.2u

CTF1786-A
3 DGND 7.4V
KN2
SCL
1 2
SKIP
SDA
VD2

NM
Q751
DATA
PGND

M2R6TP_GND
VDD4
BCLK

GND1
RESET

P402
R416 NM
DGND1

P401
LRCK
WAIT

X1

CDSRQ
2SD2396(K) VD1

C453
CCG1218-A
C447
C446 NM
CDSTBY

HSPC16701B02
C448 0.1u/10
C445 0.1u/10

0.1u/10
C455 CSS1848-A *1

1u/10
C452
0.22u/16 R701
220

L418 NM
R718

L417 NM
A B C, D 47k
L405 NM R702

47k
C454 68n NM

10u/10
NM

R753

NM
RFGND
L406 CTF1389-A CTF1389-A

R417
NM 100k
NM
L416 NM L407 NM NM 0.27uH

820
R752

C751
R415 0
L415 L408 4.7uH 4.7uH 1.5uH

64
63
62
59
58
57
56
55 C451
54 0.1u/10
51
49
*1 VDCONT Q752

C753 CCG1192-A
L414 L409
NM NM NM 0.39uH 3 4
1 48 CTF1786-A

220
750
L410 47uH 47uH 2.2uH

R401
R402
TCFM
2 47 C444 2 5 GND

TVDAC
OSCIN 52
10k
L414 NM CTF1786-A NM

R754

OSCOUT 53

VCC-PLL
VCC-REF

GND-PLL 60
PLLTEST 61
CCG1218-A 2.2u 1 6

0.1u/10
3

DACOUTR
DACOUTL
VREFDEC
GND-REF
VDDIO1V2
46 C443 R403 390 390 330 RN4983 R703

VDDPLL1V2 50
RFGND C401 FMMIXDEC TEST 5 4
NM 4 R408 470 470 360

D401
D402
VDD_CORE 45 NM
FMMIXIN2 3

VCC-ADC_DAC
GND-ADC_DAC
6

D751
L401

KP2311E
150

KP2311E
C410 R409 NM NM
150
150

C402 5 GND1V2 44 0

C752
FMMIXIN1 FMPINDRV GPIO0 7 2
0.27uH 0.01u/16 R411 680 680 390

RKZ8.2KG(B2)
33p/50 6 FMPINDDEC GPIO1 43
GNDRF R415 NM 0 8 1 C
C403 GPIO2 0
7 42

NM
R716

1
R715
R717

TCAM GPIO3 C419 NM NM 15p/50

6p/50
C409
C408
C407
C406
C405

L402
1u/10 4.7k

0.15u
8 41

0.01u/16

0.01u/16
0.01u/16
C420 0.01u/16 0.01u/16 C
220
220
100
220
100

VCCRF GPIO4 NM GND

1k

AGND IC401
orRFGND C404 NM 9 40 C421 3p/50 NM NM 1

2
2

CK_SEL TDA7706 GPIO5

10 39 C423 NM NM 8p/50 R704 100k C
RF GND GNDVCO GPIO6
R711

L403 11 38 C428 100p/50 100p/50 22p/50

C412 LFREF GPIO7 C702 10
0.1u/10 C411 C430 DCH1246-A NM NM
R706
R707
R708
R709
R710

CTF1786-A 12 37 R705
LF1 GPIO8 C432 82p/50 82p/50 2p/50 NM
0.01u/16 13 36 C701

C413
0.1u/10
PINDDEC NM
NM

C433 DCH1246-A NM NM
L701

A GND VCCVCO GND3V3

C414 0.01u/16 14 TCAM2 PINDIN 35 C442
L404 VDD3V3 C436 NM NM 0.1u/10 0.01u/16 C703
CTF1786-ARFGND C415 15 34 0.1u/10 TUN_SCL C439 NM NM 0.1u/16
I2CSCL NM
DGND C441 10p/50 NM NM GND

RDSINT

VREG3V3
RSTN
CCG1192-A 16 I2CSDA 33 TUN_SDA
10u NM CCG1218-A

NM
RFGND C447 NM

C461
GNDLNA
LNAIN
LNADEC
LNAOUT
LNAIN2
LNAOUT2
LNADEC2
AMMIXIN1
AMMIXIN2
GNDSLINK
VDIG
VCCREG1V2
REG1V2

C417
C416
C418

0.1u/10
0.1u/10
0.022u/16 C448 0.1u/10 0.1u/10 NM

L413

17
18
19
20
21
22
23
25
26
27
28
29
30
31
32
GND
RFGND C419 15p/50 R403 390 C424

CTF1786-A
C420

NM 24
L406 TUN_RST
0.01u/16 L408 0.01u/16 B.UP

C427
*1

C426
C425

0.1u/10
CTF1389-A 4.7uH GND

R410 0
SW5V

R409 0
CCG1192-A

0.1u/10
C460
L405 10u

1M
L407

NM
68n

R404
3.3V

NM
0.27uH

C438
C430 1u

C437
C440

1M
33
C436
C439
0.1u/16

0.1u/10

R407
1000p/50

FH-X700BT/XNUC
DCH1246-A

NM
RFGND

C422
*1 C431 NM DGND 1/4W 1/4W
R412 R413

L409 C423
*1
VDSENS
VDCONT
CDSRQ
CDSTBY
CDSKIP
CD_SDA
CDRST
CDDATAIN
CDSCKIN
CDLRCKIN
CDWAIT

0.39uH 8p/50

R406
C428

3p/50
C421
*1

100p/50
8.2 8.2

R408 470
DGND

C441
L411 NM FLASH ROM L6

10p/50

NM
R405
MCLK

C429 L410 *2 N

NM
BSENS
ASENS

C432
R414 0 IC681

C435

82p/50
RESETB
VDCONT
CDWAIT

RF GND

C434
IC681

3
3

47k

*2
TUN_RST
47k

0.01u/16 47uH
R681

1u
R684

0.47u/10
47k

R411 680
C433 C458 C459 1 8
R685

RF GND A PEB040A8 CS
VCC
NM 2 NC/SIO3 7
*1 RFGND DCH1246-A NM SO/SIO1
B, C, D PEB039A8
0.1u/10

NM

DGND AGND RF GND DGND AGND

3 SCLK 6
WP/SIO2
4 5
GND SI/SIO0
47k

R682
C681

C682
47k

KN1
R683
C683 3p/50

M2R6TP_GND
CN971
VKN1192-A
BT Connector
VCC 16
DGND
47k
C625

NM
C622

R638
0.1u/10

VCC 15
22p/50

C971
GND 14 C973
GND 13 R974
47p/50 100
8
7
6
5

BTDATA R636
BTDATA 12
R975 100 BT_BCK
47k

BTBCK 11 47k
100
100
100

R632
100
47k
100
100
100

R976 100 BT_LRCK R637

C620

BTLRCK 10
L971
0.1u/10

C624
C623 0.1u/10

R635 1k
R634 1k
TDI 3

47k
TCK 1
TMS 2
TDO 4

GND 9
0.1u/10
R633
R631

NM
R630
R629
R628
R627
R626
R625

D
C621 0.1u/10

BT_RST
NRST_CPU 8
BTTX
CN23 SYSTOBT 7
R971 NM BTRX
90
89
88
87
86
85
84
83
82
81
80
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63

BTTOSYS 6
R640
4.7k
R639
4.7k

GND 5 R972 NM CP_SCL 91

NM
Vss
TCK
TDI
TDO

Vss
Vcc
TMS

Vcc
Vss

4
C972
QIO1
4

QIO3
QIO2
QIO0
QSSL
PVcc

92
PVcc

MIC1P 4 CP_SDA
ASEBRK 62

/ASENS
TUNRES
VDCONT
MD_CLK 79
QSPCLK

R641
/BSENS

GND 3 TUN_SCL 93
/CDWAIT
MD_BOOT

GND
AUDIO_X1

R973
AUDIO_X2

EVOL_MCK

EVOL_RST

R642
MIC1N 2 TUN_SDA NM 94 CP_SCL
0 CP_SDA
GND 1 CD_SCL NM 95
TUN_SCL M
GND CD_SDA 96 TUN_SDA
GND

MIC1P
MIC1N
CDSRQ 97 CD_SCL
CD_SDA
TESTIN 98
JA892 /CDSRQ
YKS5035-A R643 99 DDON
47k

R669

6 MIC1P DDON TESTIN

(RMIC) 5 100k 100
MIC1N Vss
R668 47k

4 C626
3 LTC014YEB 101 PVcc
2 Q601
1 KEYD BT_TESTMD 0.1u/10 102 BT_TESTMD
(W/R) C627 22p/50
1 R891 1k KEYD2 KEYD R644 100 103
JA891 3 BCLK EVOL_BCK IC601

NM
KEYAD2

NM
KEYAD KEYAD

C894
2 LRCLK

C893
R645 100 104

VA891
EVOL_LRCK

R893
NM R892 1k R5S726A0D216FP

1000p/50
1000p/50

VA892 NM
91
/16
92

C628
u/16
M

22p/50 105 KEYD

 GND 1 CD_SCL NM 95 CP_SDA
TUN_SCL M
GND CD_SDA 96 TUN_SDA
GND

MIC1P
MIC1N
CDSRQ 97 CD_SCL
CD_SDA
TESTIN 98
JA892 /CDSRQ
YKS5035-A R643 99 DDON

47k

R669
6 MIC1P DDON TESTIN
(RMIC) 5 100k 100
MIC1N Vss

R668 47k
4 C626
3 LTC014YEB 101 PVcc
2 Q601
1 KEYD BT_TESTMD 0.1u/10 102 BT_TESTMD
(W/R) C627 22p/50
1 R891 1k KEYD2 KEYD R644 100 103
JA891 3 BCLK EVOL_BCK IC601

NM
KEYAD2

NM
KEYAD KEYAD

C894
2 LRCLK

C893
R645 100 104

VA891
EVOL_LRCK

R893
NM R892 1k R5S726A0D216FP

1000p/50
1000p/50

VA892 NM
C628 22p/50 105 KEYD

NM

C891
C892
0.1u/16

0.1u/16
GND 106 EVOL_DATA

10k
W.REM

R646

D602
W.REM&MIC KEYD 107
DIN R647 100 Vss
GND CLK 108 EVOL_CK
Q531 R648
5

1k C629

5
L531 LSAR523UB 109 Vcc

C631
R649 1k 0.1u/10 110

22p/50
NM DATA EVOL_DT
R536 4.7k CPPWR STB R650 1k 111
R540 EVOL_CS
C630 112

47k
PVcc

R531

C531
47k

0.1u/10
CP_SCL

2.2k
SWVDD5 0.1u/10 113

R533
R532
2.2k
R537 100 SWVDD
R539 CP_SDA 114 Vss
R538 100 PCL PCL
47k 115 RAM_MON
CPRST RAM_MON 116 MUTE
SYNC
IC531 USBCTL

R651 47k
USB5V MUTE 117 CD
337S3959 /USBFLG
L551 USB&USB5V

4.7u
C553 D551 R652 CD

3.3V

B.UP
SYNC SYNC 118
1 8 CTH1524-A 0.01u/16

R534 2.7k
GND PAD VCC CMS03 USBCTL 2.2k 119
2 9 7

C552
C551
1u/16
SDA RST IC551 FLG 120

C565
3 6

220u/16
RGBDT/DIMMER

Vss

BD9876EFJ
PVcc

SYSPW
ILMPW

RGBCK/ILMCLR1

BTDATA

NM
BT_LRCK
PVcc

ROM
Vss
Vcc
RGBCS/ILMCLR2

Vss
BTRX
BTTX
KYDT
DPDT

0
ANTPW
CPRST
CPPWR
TELIN
CDSTBY

Vcc

BT_TESTIN
NC1 SCL

CCG1222-A
4 5

R535 4.7k
R552
R653

NM
1
2 BTRST
3 PVcc
4 BT_BCK
6
7
8
9

1 8

NM

470
R661

4.7u

220u/6.3
NC2 NC3 Lx VCC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

GND

D552

C532
LX VCC
2 7

C555
10k

0.1u/10
RB056L-40
GND 9 BST

C558
GND BST

6800p/25
NM
3 6 BTTESTIN

C564 CCG1201-A
C554
C633
DDON

C557 1u/10
GND

C556
VC EN

R555
ROM

VC FIN EN
4 5

R553 TP1
SYNC

180k D
R551
FB SYNC

6.8k
FB SYNC
0.1u/10

47k
C605

47k

R601
C604

C601
R602
TELIN1

NM
R603 47k
0 1 /10

0.1u/10

R664 10k
R604 NM

0.1u/10

iPod CP @(2.0C)

C563
C602
C603 0.1u/10

GND

43k D

R554
GND

6
6

GND
IC552
GND
RGBDT

1 5
NM

VIN VOUT DGND

R662
NM

2
GND FLG
3 4 FLG

C561
EN OC
NM

NM
1u/10
R663

C562
USBCLT
R605

NM

C560
C559

1u/10
BD2232G-G USBCTL

GND
SYSPW
RGBST/ILMCLR2

BT_RST
BT_BCK
BTDATA
RGBCK/ILMCLR1
BTRX
BTTX
ILMPW
KYDT
DPDT

RGBDT/DIMMER

BT_LRCK
OFFSET
CPRST
CPPWR
TELIN
CDSTBY
CDSCKIN

DSENS

VBUS

CN801
CKS6452-A C801
2.2k

R802

FH-X700BT/XNUC
R808
RGBDT/DIMMER

NM
DSENS 20
NOTE : R801 2.2k R805 100
AUXL 19 GND R803 22k
Symbol indicates a resistor. 18 R806 100

7
7

SOURCE
No differentiation is made between chip resistors and A FH-X700BT/XNUC 17 R804 22k R807 100
AUXR
AUXGND 16 L801 R809
discrete resistors. 11 2 2
B FH-X700BT/XNEW5 15 22
DP
Symbol indicates a capacitor. RGBST/ILMCLR2 14
C FH-X755BT/XNES R810
No differentiation is made between chip capacitors and 44 3 3
DM 13
CTF1713-A 22
D FH-X759BT/XNID RGBCK/ILMCLR1 12
discrete capacitors. US5V
USB5V 11
B DPDT 10
R813 2

CN1931 USBGND 9
R814 2.
NM

The > mark found on some component parts indicates KYDT 8

R818

the importance of the safety factor of the part. RGBDT 7

R816 2.2
ROT0 6
Therefore, when replacing, be sure to use parts of
ILM+B 5
identical designation. R817 2.2
ROT1 4

SWVDD 3
ILMGND 2 DGND
NM

ILMG
NM
NM

NM

NM

C803
NM

NM

NM : No Mount DGND 1
D801
NM

NM
NM

NM
NM

1u/10
0.1u/16

C802

USGND C804
NM
C810
C809

C805
C807
8

C806
D803 DZ2S068C
D804 DZ2S068C

8
D802
D805 DZ2S068C
D807 DZ2S068C
D809 NM

D806 DZ2S068C
C808
D808 NM
D810
D811
VA801
VA802

GRILLE DGND USBGND ILM GND

A-a A-b

A-a
A-b

47
E
A

D
C

F
B
 F
E
B
A

D
C

48
B
1 SEG0

SEG43
SEG42
SEG41
SEG40
SEG39
SEG38
SEG37
SEG36
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG0 2 SEG1
SEG1 3 SEG2
SEG2 4 SEG3
SEG3 5 SEG4
SEG4 6 SEG5

1
1

SEG5 7 SEG6
SEG6 8 SEG7
SEG7 9 SEG8
SEG8 10 SEG9
SEG9 11 SEG10
SEG10 12 SEG11

50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
SEG11 13 SEG12
SEG12 14 SEG13
SEG13 15 SEG14 SEG44 51 25 SEG18
SEG14 S18
16 SEG15

S43
S42
S41
S40
S39
S38
S37
S36
S35
S34
S33
S32
S31
S30
S29
S28
S27
S26
S25
S24
S23
S22
S21
S20
S19
SEG15 17 SEG16 SEG45 52 24 SEG17
SEG16 S17
18 SEG17 S44
SEG17 19 SEG18 SEG46 53 23 SEG16
SEG18 S45 S16
20 SEG19
SEG19 21 SEG20 SEG47 54 S46 22 SEG15
SEG20 S15
22 SEG21
SEG21 23 SEG22 SEG48 55 21 SEG14
SEG22 S47 S14
24 SEG23
SEG23 25 SEG24 SEG49 56 20 SEG13
SEG24 S48 S13
26 SEG25
SEG25 27 SEG26 SEG50 57 19 SEG12
SEG26 S49 S12
28 SEG27
SEG27 29 SEG28 SEG51 58 18 SEG11
SEG28 S50 S11
30 SEG29
SEG29 31 SEG30 SEG52 59 17 SEG10
SEG30 S51 S10
32 SEG31
SEG31 33 SEG32 SEG53 60 16 SEG9
10.2 KEYBOARD UNIT

SEG32 S52 S9
34 SEG33
SEG33 35 SEG34 SEG54 61 15 SEG8
SEG34 S53 S8
36 SEG35
SEG35 37 SEG36 SEG55 62 14 SEG7
SEG36 S54 S7/P17
38 SEG37

V1802
SEG37 39 SEG38 SEG56 63 13 SEG6
S55 S6/P16

CAW2025-A
SEG38

IC1802
40 SEG39
SEG39

PDC202B
41 SEG40 SEG57 64 S56 12 SEG5
SEG40 42 SEG41 S5/P15
SEG41 43 SEG42 SEG58 65 11 SEG4

2
2

SEG42 S57 S4/P14

44 SEG43
SEG43

ILMGND
45 SEG44 SEG59 66 S58 S3/P13 10 SEG3
SEG44 46 SEG45
SEG45
GRILLE uCON

SEGMENT LCD
47 SEG46 SEG60 67 S59 S2/P12 9 SEG2
SEG46 48 SEG47
C1856 NM SEG47 49 SEG48 SEG61 68 8 SEG1
SEG48 S60 S1/P11
50 SEG49
C1858 SEG49 51 SEG50 SEG62 69 7 SEG0
NM SEG50 S61 S0/P10
52 SEG51
SEG51 53 SEG52 SEG63 70 6
C1857 NM SEG52 S62 VDD1
54 SEG53
SEG53 55 SEG54 SEG64 71 5 C1804 1u/10
SEG54 S63 CF2
56 SEG55
SEG55 57 SEG56 SEG65 72 4
R1882 R1881 Q1857 SEG56 S64 CF1
58 SEG57
1 6 LSCR523UB SEG57 59 SEG58 SEG66 73 3
0 68 R1866 SEG58 S65 VSS1
60 SEG59
2 5 SEG59 61 SEG60 SEG67 74 2
100 SEG60 S66 XT1
SEG61

D1882
62
X1801

3 4 SEG61 63 SEG62 SEG68 75 S67 1

V3
CSS1547-

R1884 R1883
V2
V1

SEG62 RES

S69
S70
S71
S72
S73
Q1858
P70/INT0/T0LCP

SEG63
P00
P03

64 S68
P71/INT1/T0HCP
RMIN/P73/INT/T0IN

P01
P02
P04
P05
P06
P07
URX/P35
UTX/P34
5.000MHz

LSCR523UB SEG63 65 SEG64

0 68 R1867 SEG64 SEG65

SMLVN6RGB2U(A)-TRB
SEG65 66

76
77
78
79
80
COM0 81
COM1 82
COM2 83
COM3 84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99

67 SEG66
100

100 SEG66 SEG67

SEG67 68
69 SEG68

FH-X700BT/XNUC
R1886 R1885 Q1859 SEG68
DGND

70 SEG69
LSCR523UB SEG69 COM0
C1803
C1801
C1802

71
R1809

0 68 R1868 COM0
COM1 72 COM1 D1801
100 COM2 73 COM2
COM3 74 COM3 NM
R1810
0.1u/10

47k
C1805

0.1u/10
0.1u/10
0.1u/10

10k

1 6

3
3

SEG69
KST0
KST1
KST2
KST3
KDT0
KDT1
KDT2
KDT3
KYDT
DPDT

COM0
COM1
COM2
COM3
DGND
DGND

2 5

D1883
3 4

SMLVN6RGB2U(A)-TRB
RGB
C1859 NM
C1861 NM
KST3
KST2
KST1
KST0

C1860 NM
SOURCE
4
4
4
4

3
3
3
3

Q1851
LSCR523UB
R1854 R1941
2
S1821

S1834
S1826

S1838
LEFT

NM
CSG1155-

2
2
2
2

CSG1155-

1
1
1
1

CSG1155-

CSG1155-

1k
DSP

1 6
PHONE

NM

Q1871
R1942

R1918 R1905 R1855 KDT0

2 5 LSCR523UB
0 68 R1872 NM

ILMGND
3 4 REM
4
3

D1884
4
4
4
4

1
3
3
3
3

100
GND
IC1941

R1919 R1906 Q1870 2

DGND

C1941
6

S1842
3

C1871 NM LSCR523UB VCC

CSG1155

GP1UXC14RK
S1828

2
S1822

S1835

S1839

SMLVN6RGB2U(A)-TRB
R1873 3
2
2
2
2

0 68 Q1852 CCG1192-A
1
1
1
1

CSG1155-
CSG1155-
CSG1155-

CSG1155-
LIST
EJECT

LSCR523UB 10u
C1873 100 KDT1
DGND

NM R1856 R1943
SOURCE

R1920 R1907 Q1869

RED Key

LSCR523UB 1k NM
C1872 NM
4
3

0 68 R1874 R1857
4
4

100
3
3

R1944

100

4
NM

ILMGND
4

1
S1840
4

2
1
S1836
S1823

CSG1155-

REMOTE
2
2

CSG1155-
CSG1155-

1
1
RIGHT
KEY MATRIX

KDT2

1 6 Q1853
GREEN Key

LSCR523UB
4
3

2 5 R1858
DGND
4
4

3
3

3 4 1k

D1887
S1824

5
S1832

S1837
2

C1854
1u/10
1

CSG1155-

R1859 IC1851
C1855

0.01u/50
2
2

CSG1155-
1
1
BAND

CSG1155-
BACK

C1864 NM 1 AO1 14 KDT3

NM
ILMGND

SMLVN6RGB2U(A)-TRB
VSS
BLUE Key

2 AO2 13
C1863 NM VFS
3 AO3 12
C1862 DI
NM 4 AO4 11
4

CLK
5

5 AO5 10
R
MULTI-C
 5 6 7 8

REFERENEC AREA MAP B KEYBOARD UNIT

KDT3

BAND GRILLE uCON & LCD :1801-1820

S1824
4 2 KEY MATRIX&ROTARY :1821-1850
3 1
RGB :1851-1910
USB :1911-1920
CSG1155-
AUX :1921-1930
CONNECTOR :1931-1940
BACK
S1832
REMOTE :1941-1950
4 2
3 1 SOURCE
CSG1155-

KYDT
5
S1837 DPDT
4 2
3 1 B
D1932

D1931
NM

NM
CSG1155-

DGND SWVDD
L1801

NM CONNECTOR
R1824

R1825
NM
27k

S1830

5 2 C1825 CN1931
3 CKS6451-
NM DGND
4 1 1
DGND ILMGND 2
ILMGND SWVDD 3
CSD1168-
MULTI-CONTROL ILM+B
ROT1 4
ILM+B 5
DGND
ROT0 6
RGBDT 7
R1931 KYDT 8
2.2k USBGND 9 C
R1851 R1932 DPDT

A
2.2k 10
2.2k USB5V 11
R1852 2.2k RGBCK 12
C1855
R1911 DM 13
CN801
1u/10 R1853 2.2k NM RGBST 14
C1854
R1912 DP
0.01u/50 15
NM AUXGND 16
L1911 USB:±0.0 dBs
AUXR 17
10p/50

10p/50

10p/50

NM
14
13
12
11
10
9
8

2
ND AUX:+2.2 dBs SOURCE 18
CN1911
VDD
CSB
VSS

NC2
VFS

CLK
DI

AUXL 19
BH2228FV

CKS6443
C1851

C1852

C1853
IC1851

DSENS 20
AO1
AO2
AO3
AO4
AO5
AO6
NC1

1
4

1
1
2
3
4
5
6
7

2
BLUE LCD DGND
3
DGND
GREEN LCD USB 4
BLUE Key RED LCD 5
6
D
D1911

D1912
NM

NM
NM
0.1u/16
R1858

R1860

R1862

R1864

C1911
1k

1k

1k

1k

C1913

C1912
LSCR523UB
LSCR523UB

LSCR523UB
R1859

R1861

R1863

R1865
NM

NM

NM

NM
Q1855

0.1u/16
Q1856
Q1854

ILMGND DGND
ILMGND ILMGND ILMGND ILMGND
C1914

NM
ILMGND DGND
C1915

NM
R1875

R1876

R1877
100

100

100

ILMGND DGND
CTF1389-A

CTF1389-A

CTF1389-A
L1802

R1922
R1921

R1923
L1803

L1804
NM

NM

NM
LSCR523UB

LSCR523UB

LSCR523UB

JA1921
Q1866

Q1868
Q1867

CKN1094-
3
AUX 2
1 E
R1899

R1901

R1903

C1921

C1922
68

68

68

NM

NM
NM

NM

NM
NM
R1900

R1902

R1904

D1921

D1923

C1923
0

D1922

C1867
NM

ILMGND
C1866
NM
C1865
NM
NM

NM

NM

NM

NM

NM
5
4

7 6 5 4 3 2 1 7 6 5 4 3 2 1
C1864

C1863

C1862

C1868

C1870

C1869

R R
2
3

B G B G

D1885 D1886
MSL0101RGBU MSL0101RGBU

D1887
6RGB2U(A)-TRB F

B
FH-X700BT/XNUC
5 6 7 8
49
 1 2 3 4

10.3 CD CORE UNIT (S11.6STD)

PICKUP UNIT(P10.6) (SERVICE)

A CXX3556
V3R3

E:P5+P10

R101 R102 R103

F:P1+P6

2.7
(1/10W)
(1/10SR,1608)

2.4

C104

4.7u/6.3
(2125)
R

2.4
R
PUEN R
LD1 Q102 R
LTA123JUB

0.047u/16
C214
LD Q101 R109 LD

VCC
2SA1577(QR) 2.2k
R2

C102

D101
NM

NM
39

LD-
15 15
ASY
LD+
14 14 V+3A EFM
B+D BD
13 13
B VCC
12 12
V+3A
ATEST

75
74
C101

NM
P5+P10 E
11 11

ATEST
GND
10 10

C110
C111
P1+P6 F

NM
NM
9 9
VREF REFO 76
8 8 C221 A.VDD1
VR 77

C201

NM
R108
7 7 A.GND1

1M
0.1u/10
A+C
6 6
AC PD
PD
f C216

1800p/50
78
79
RFI
MD
5 5 RFAGC AGCO
TOM C220 80
TOM
HOLOGRAM UNIT 4 4
0.1u/10
C3T
FOM FOM C219 81
3 3 AGCI
FOP FOP 0.1u/10 82
2 2 RFO RFO
FOCUS ACT C228 R229 83
TOP

R218 R217
TOP

5.6k
1 1 EQ2

4p/50
C218
TRK ACT 27p/50 470 84
EQ1
C217 R216 85

4.7k
C205 RF2-
56p/50 1.2k 86
TOM
FOM
FOP
TOP

NM RF-

AC
BD
F.ACT: Applying positive voltage to FOP, 87

E
F
A.GND2
the lens approaches DISC. CN101 C204
C222
0.1u/10
88
A.VDD2
CKS4808-A NM 89
T.ACT: Applying positive voltage to TOP, AC
A
C the lens moves outer circumference of DISC. BD 90
B
F 91
F
E 92
E
REFO 93
REFO1 REFOUT
REFO2 C229 d C223 94
95
FE-
FE 68p/50
0.1u/10 FEO
1608:PARTS 96
* NO MOUNT PARTS (NM) C236 ADCIN ADCIN
C205 C209 C238 C224
C240 C307 C308
0.1u/10 c 47p/50
97
98
TE-
TE TEO
C708 C225 99
Land for manual soldering 0.01u/16 100
TE2
R101 R102 R103 TEC TEC
R246
2125:PARTS

LD
C239

NM
C104
M1 SPDL MOTOR

1
2
CXE2273 LD
PD
BLK
SOM Parts with Polarity
D
IC201 IC301
RED D101 VDD
SOP Q101 Q102 Q201

C202
C301

GND
BL
LCOM

YW
LCOP

M2 LOAD/CRG MOTOR
CN702

2
CXC4026 ACTUATOR/

C307
MOTOR DRIVER
IC301
7 NM
1u/10
(1608) 1
BD8223EFV
SPIN 28 SIN
8 MD
VDD 1

2 POWVCC CIN
SOM SLIN 27 SD
SPO-
C315

E HOME 3 SOP
LCOM C312
3
4
SPO+
BIAS 26
25
FIN NM
a9 FD
S901 HOME
SLLDO-
TKIN
5
431

HOME LCOP 5 FCIN 24 TIN TD

2

NM SLLDO+
CSN1080-A 6 CNT 23 CLCONT
S905 NM 8SNS POWGND
7 LDIN 22
4
FOP LOEJ
431

8SNS TKO- 29 GND

2

FOM 8 21
MUTE
S903 1 DSCSNS TOM 9
TKO+
FCO-
PRTOUT 20
CONT
43 1

DSCSNS TOP 10 PREGND 19

2

C308 FCO+
CSN1081-A 11 PRTLIM 18 R309 47k
TKRNF
DSCSNS 1u/10
(1608)
12
13
FCRNF
PRTF 17
16
MOTOR DRIVER LOGIC TABLE
PRTT LOAD EJ PLAY OFF
TKCDET
SWITCHES: 14 PREVCC 15
FCCDET CLCONT H H L L
0.1u/10
C306

CD CORE UNIT (S11.6STD) LOEJ H L - -

NM
NM

CONT L L H L
S901:HOME SWITCH.........ON-OFF
C314

C313

S903:DSCSNS SWITCH.....ON-OFF VD
C301

NM

The underlined indicates the switch position. PGND

F
CLCONT
CONT
LOEJ

C
FH-X700BT/XNUC
50
1 2 3 4
 5 6 7 8

MD
R305 SD

R302 TD

R301 FD

PUEN
C CD CORE UNIT (S11.6STD)

R307

1k
1k

0
0
C302
C303 1000p/50
1000p/50 PUEN
C304

R304

R303
C305 0.022u/16

12k

12k
0.1u/10

R308

R306
4.7k

4.7k
R310

TEMP

ADENA
4.7k

/CDSRQ
SKIP
R311
R312 4.7k
R313 4.7k
4.7k GND

0.1u/10
0.047u/16

3300p/50
C214

C213

C212

R246

C235
(1608)

NM
NM
VDD TEMP
TEMP
R215
e
MDX

R260
39k TH201

10k
Q201 NM
0.1u/10
R214

NM
10k

b MONI2
MONI1
MONI0
C215

C16M
ASY
MDY

EFM TESTIN Mask Flash

ATEST
B

GND
R232 0 10k
ADENA
R281 56 22

LRCK0
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
ADENA
R282 56 22
MD
EFM

SD

TEMP
TD
FD

VDCONT
ASY

SD2

VDSENS
TEST

/CDSRQ
ATEST

AD.GND
AD.VDD

/ADENA

SKIP
MONITOR_3
MONITOR_2
MONITOR_1
MONITOR_0

/PUEN
R291 56 22
IO.GND2
IO.VDD2

/TESTIN
R294 470 0
76 50 BSCK0 /WAIT
A.VDD1 PC3
77 49 SDA
A.GND1 SDA
C216 78 48 SCL
RFI SCL
1800p/50 79 47 R291 LRCK
AGCO /WAIT
80 46 C283 56
C3T TX/EMPH
C219 81 45 R283 NM R292 BCLK
AGCI LRCK
0.1u/10 82 44 R281 56 0 C281 C282 0
RFO SCKO
8 R229 83 43 R282 56 NM NM R293
EQ2 RF AMP, CD DECODER DOUT
DATA
0 470 84 DIGITAL SERVO/DATA PROCESSOR 42 C284 0
EQ1 CPU PA7
7 R216 85 41 NM R202 0 LOEJ
RF2- LOEJ
0 1.2k 86 40 R201 0 CLCONT
RF- CLCONT
87 39 R264 1k CONT
A.GND2 IC201 CONT R245
88 38 DSCSNS 100k
A.VDD2 PE5791A DSCSNS R253
89 37 8SNS
A NC NM
90
B 12SNS
36
R254 C
91 35 HOME
F HOME 100k
92 34 EJSW R240
E EJSW
93 33 /CDSTBY 47k
REFOUT /CDSTBY
C223 94 32 ICECK
ICECK
FE- ICECK

R296
68p/50 95 31 R297

0
FEO IO.VDD1 C211
96 30 NM
ADCIN IO.GND1 0.1u/10
C224 97 29 R237 RESET
TE- RESET
47p/50 98 28 C233 220
TEO C.GND
99 27 C210 0.01u/16
TE2 C.VDD
100 26 0.1u/10 R232
TEC VPP
INTQ(INT1)

DA.GND1
DA.VDD1

0
DA.GND

DA.VDD
REG16

VPP
D.GND

ICEMD

X.GND
D.VDD

X.VDD
REGC
REGS

ROUT

/XTAL
LOUT

XTAL
/SCK
/RST

/STB

SO

CVDD
PD
LD

A0
C239

SI
NM

VPP

CVDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

1
R294
0.1u/10

470
SO
SCK
RST

A0

ICEMD
STB

SI
INTQ

X201
CSS1603-A
D
VDD2
VDD1
3
C203

(1608)

C209 16.934 MHz

0.1u/16 (1608)

0.1u/16 (1608) VDD

C299 0.1u/10
NM
C202
NM

SCK

C238

C240

GND
CVDD
SCK
VPP
RESET

6
ICECK

CDSTBY
CDSRQ

RESET
SKIP
SDA
SCL

VD1

VD2

CN701
10 GND
6 SO

CKS6146-A
8 SI

I/O

CN702
4
2

VD
1 VD 7.5V
NM R709
2 VD 7.5V
/CDSRQ
3 /CDSRQ
0 R706
CVDD 3
ICECK 5

VPP 9
SCK 7
VDD 1

/CDSTBY /CDSTBY
4
SCL R702 220
5 SCL
SKIP 100 R708
6 SKIP
SDA
RESET
R701

100
0
7
8
SDA
RESET
A E

9 VDD 3.3V CN701

10 GND GND
DATA
11 DATA
BCLK
12 BCLK
LRCK
13 LRCK
1000p/50
C710

C705

C707

C708

14 GND GND
NM

(1608)
NM

NM

15 PGND
LOGIC TABLE /WAIT
GND
16 WAIT
J PLAY OFF
H L L IIC-BUS
R711

R710

C703

C702

C701
NM

NM

NM

NM

NM

L - - Digital
PGND
L H L
WAIT

GND1
GND2

GND3
DATA

LRCK
BCLK

i h g
F
PGND1
PGND2

C
FH-X700BT/XNUC
5 6 7 8
51
 1 2 3 4

10.4 BT UNIT

R28

1k
C34
1u/10

NM
R27
C35
NM

NC
24 1
R30 1k

R29 1k

NC
23 2
MIC_BIAS VSS
22 3
C
C23
220u/4

MIC1P BT18ON
21 4
MIC1N BT1.8V
20 5
BOOTS BT1.8V 3.3V
19 6
R38 RESET
GND 18 7 BT1.8V
NM 0 BT3.3V BT3
17 8 DBG_Tx
C37
0.1u/16

IC21
C36

16 9
CCG1192-A
NM

DBG_Rx

NM
1 6
C24

1u/10
C39

10u C38
15 10 VOUT VIN
2 5

CCG1192-A
C22

NM
C32

C33
14 11 VSS1 VSS2

10u

C28
3 4
10u
220
220
220

13 12 ON/OFF NC
SYSTOBT
BTTOSYS

GND S-1172B18-E6
CN21
R39
R40
R41

GND GND
D CKS6346-A
BTDATA
BTSCK
BTLRCK

R32 NM

R33 NM
BT MODULE R34 NM

D
FH-X700BT/XNUC
52
1 2 3 4
 5 6 7 8

D BT UNIT

CN23
R28

1k

C34 CKS3857-A
1u/10
1 VCC
NM
R27

2 VCC
C35
NM 3 GND
4 GND
5 BTDATA
6 BTSCK
A

A
7 BTRLCK
C
8 GND

CN971
9 NRST_CPU
3.3V
10 SYSTOBT
11 BTTOSYS
BT3.3V IC22
S-1206B33-U3 12 GND
13 MIC1P
CCG1192-A
NM
CCG1192-A

NM
NM

3 VOUT
1u/10

1 VSS

14 GND
C26
10u C38

2 VIN
C29

10u
C25

C21

15 MIC1N
C28

16 GND

GND
GND
D
C31
NM

D21
NM

NM
D22
D27
NM

GND
E

D
FH-X700BT/XNUC
5 6 7 8
53
 1 2 3 4

10.5 WAVEFORMS

- CD CORE UNIT(S11.6STD) Note : 1. The encircled numbers denote measuring points in the circuit diagram.
A
2. Reference voltage REFO1(1.65 V)

1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div

3HOME 5 V/div 5CLCONT 5 V/div
4LOEJ 5 V/div 4LOEJ 5 V/div
6VD1 10 V/div
12 cm CD Loading operation 12 cm CD Loading operation

Ref.: Ref.:
GND GND
B

Mode: Mode:
Normal Normal

7SIN 1 V/div 1 s/div aFIN 200 mV/div 500 ms/div cTE 500 mV/div 200 ms/div
8CIN 500 mV/div bRFOK(MONI_2) 2 V/div dFE 500 mV/div
9TIN 500 mV/div 7SIN 2 V/div

12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

dFE 500 mV/div 20 ms/div eMDX 2 V/div 50 ms/div eMDX 2 V/div 5 μs/div
aFIN 500 mV/div 7SIN 500 mV/div 7SIN 500 mV/div
cTE 500 mV/div
D 9TIN 500 mV/div
CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

E
aFIN 500 mV/div 200 ms/div cTE 500 mV/div 2 ms/div fRFAGC 1 V/div 500 μs/div
dFE 500 mV/div fRFAGC 500 mV/div cTE 500 mV/div
9TIN 500 mV/div

Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3)

Ref.: Ref.: Ref.:

REFO REFO REFO

F Mode: Mode: Mode:

TEST TEST TEST

FH-X700BT/XNUC
54
1 2 3 4
 5 6 7 8

A
fRFAGC 1 V/div 2 ms/div fRFAGC 1 V/div 200 ms/div gLRCK 2 V/div 10 us/div
cTE 500 mV/div cTE 1 V/div hBCLK 2 V/div
9TIN 500 mV/div 8CIN 500 mV/div iDOUT(DATA) 2 V/div
7SIN 2 V/div
32 Tracks Jump waveform
(Zoom of 100 Track Jump waveform) Search operation(Outter to Inner) Digital Out waveform

Ref.: Ref.: Ref.:

REFO REFO GND

B
Mode: Mode: Mode:
TEST Normal Normal

1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div

5CLCONT 5 V/div 3HOME 5 V/div
4LOEJ 5 V/div 4LOEJ 5 V/div

12 cm CD Eject operation 12 cm CD Eject operation

Ref.: Ref.: C
GND GND

Mode: Mode:
Normal Normal

fRFAGC 1 V/div 500 μs/div

9TIN 1 V/div
cTE 1 V/div
aFIN 1 V/div
Black Dot (800 μm) during play D

Ref.:
REFO

Mode:
Normal

FH-X700BT/XNUC
5 6 7 8
55
 1 2 3 4

11. PCB CONNECTION DIAGRAM

11.1 TUNER AMP UNIT
A NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP UNIT
> P 251 (A,6,130) Fuse 3.0 A CEK1386
several destination.
For further information for 150
respective destinations, be sure
to check with the schematic dia-
gram. JA891
2.Viewpoint of PCB diagrams
1
W.REM&MIC
PREOUT JA892
Connector Capacitor 140 C892
R891 10 2
C260 2 2 3 C891
4 IC301
6 5 JA251 3 2
1
VA891 5 1 4 6 R892 C319 1 5 15

SIDE A C894 C320

R252
R259
3

R251
R256

C257
C261

R258
C893

C258
R254

R253
Q252 VA892

C253
R893

C254
Q251 C331 C333 C334 C332

R257
1 R255 C328 C313
130 P251 1 C255 C307 C303

B C256
C318
C301 C305
C321
C96
C259 C251 C317 C310
SIDE B C252 R304

C311
C309

R303
R301
C312
P.C.Board Chip Part R302
R307

D551 R555 C562 R311

C551
C556
120

R309
C557

C563 C558
C555 C564

5
IC551
C553 R553 R552
110

C554
R551
R554

1
1
C552
C565 L551

D552

100
C

90

80

70

60

50 D CN23

40

30

20

10

F Y
FRONT
0 X
10 20 30 40 50 60 70 80
A
FH-X700BT/XNUC
56
1 2 3 4
 5 6 7 8

A
SIDE A
CEK1386

10 20 C326 POWER SUPPLY L901 Q751

IC301
15 25
JA901 E
D751 C752

1
C325 2 4 6 8 10 12 14 16 18 R752

FUSE

1
1 3 5 7 9 11 13 C753
C333 C334 C332 15 17
Q752
C313 C751
C307 C303 C327
R312 D902 D901
C305
C321
C965 R306 C335
C324 C323 C314
B
R305
R943

C310
C322

R304
ANTENNA
D301
C311
R303

D941
1

C941

C312 R307
R302 C901
R944

R311 Q301
R942 JA401
C330
D302

E
R941
C329

C911
R309

Q941 C930
KN2
C201

R953
R951
C202 L951
C204
C203

C233
C234

R962
R963
C966
C205

C229

C963
C228

P402
IC201 C969 1
1

D951

C421
40

C206
1

C218

C422
C419
IC961 R405

P401
R961
R952

C212 5
5

E
35

C226 L409 L405

C231 1

R406
C227 Q951
C207 L407 C410 D401
C211 C961
10

C208 C962 C423 C420

30

Q302 R401
C232 C210 C213 L406 C409 C408

R403

L408
C461

L401
C403
C214

L403
C209
15

C221 E L402

C413
L202

25

C215 L201 L404

C224

C225
C236

C219 C402 C407 C406 C405

C223

C417
C424
C418
C415
C235
20
C216

C404
C414
C416
C412
C217 C220 C425 C411 C401 D402 R402
R685
C681

C453
L681 C426 R404 R409
C

C454
R681 C458

C455
R408
E

C427
L531 C429 R407 L420
1

C682 15 10 5 1
C619 C428
R536

Q531 L410 L419

R631

R531 R684 IC681 C683

R639

R636

C532 C622
R640

20

C531

60
X603 C460 C457
R633

C452
R629

C430

R534 R638 R754 C432 C456

R682

R632 R683 1 IC401 C451

R535

R410
R628

R625

C433
25

R753
R626

55
C625 R411 C431 R417 C450
IC531 R637 R624 C618 C441 C434
1
30
C623
C624

L411

50
C621

5
C620
R627

R642
R630
R537

R622
R540

X602
R634

X401
R635

1 R623 R414
35 40 45
R641
1

C435 C446 C448

C440
C612
C613

90 85 80 75 70 65
R538 C449
60

R618

C459 C447
R619

C436
R532
R533

R539 C443 L418

L413

C627 R643 C437 C444 C445

R617
95

C442
D601
55

L414

C628
R415

C626 L417
R416 L415
100

R645 L416
R648 R614 R615
50

C438

R649 R644 C608 C671

C439

C611
105 110 115

R650 C631 R647 IC601 IC671 R412 R413

R613
45
D602

R612

C610 1 X601
1
R646

40

C629
C609 C607
R611
C630 D671
C606
35

R668 R651 Q873

120

C633 1 5 10 15 20 25 30 C672
R610 R671 Q872 E
E R652
R669

R879

R616
E
R608

R873

Q874
D911

D912
R653

R601

C617
C616

Q601 C602 L601

D
C604
C603

1
C601 R621 R871
C605
R605
R607

R661
R973 R609 L602
R606

C871
R876

R663 R602 R872

C971
D872
C615
C614

R603
R620

R664

R662 R659
D871

R604
R660 E
CN971
R875
R874

Q871 C914
15

R974 E
R975
C973 Q875
R976 C928 C918
10

3 C972
L971
C929

R971 C925
R972 C917
R705
C702
5

C915
C913

C926
C922
L701 C920
C916
R704
C701

C924
R912
C927

C703
1

C919
R711

C921 R911 C923

C912
R701

R719 C704
C705
C706

10 5 1
C708
R702
C707 IC911
R717
R716
R715
R707

R709
R710

R718
R708

R706
E
15 10 5 1
C CN701
CN701 R703
1

R877
C872
C852
KN1 C561
IC552 R878
1

C873
R809
R812
R810

L851 C802
R806

R805
R811

R807

C851 C560 R801

C811
C559 R808
R817

R816

R815

R851
R814

1 5 L801
C805 C808
C803 C809 IC801 R804 R803
D802
1
R802
D801

D811
C807

R813 D803
D805
D804
D809

D806
D807
VA801

D808
D810

VA802
C810 C804
R818
CN801
B
1 5 15
CN1931
C806

10 20 C801

FRONT F

80 90 100 110 120 130 140 150 160

A
FH-X700BT/XNUC
5 6 7 8
57
 1 2 3 4

A
A TUNER AMP UNIT

TESTIN

PCL

F
160 150 140 130 120 110 100 90 80

A
FH-X700BT/XNUC
58
1 2 3 4
 5 6 7 8

SIDE B
A

150

140
1
1

130

120

110

100

C
90

80

70

D
60

50

40

30 E

20

10

X 0 F
90 80 70 60 50 40 30 20 10

A
FH-X700BT/XNUC
5 6 7 8
59
 F
E
B
A

D
C

60
B
B

1
1

EJECT
1
S1822

90
KEYBOARD UNIT

80 1 5 10 15 20 25 30 35 40 45 50 55 60 65 70
V1802
11.2 KEYBOARD UNIT

D1886
D1885 SEGMENT LCD

5
5
70 IC1941

1
1

2
2

60
1 2 3 4 5 6 DSP
1 1 1 1 1 1
S1840 S1838 S1839 S1836 S1837 S1835 S1834
D1883 1 D1882
50 1 1
5 5

1
S1826 USB

FH-X700BT/XNUC
SOURCE LIST
40 1 CN1911
PHONE S1842
1

S1828
1
2
3

MULTI-CONTROL
4

3
3

30 5
6

D1887 D1884

1
S1830

5
5
1

1 1 AUX
20 S1821 S1823
JA1921
LEFT RIGHT 3 1

2
BAND BACK
10 S1824 S1832
1 1

Y
0

4
4

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160

X
SIDE A
 B

F
C

D
A

61
B
SIDE B

CN801

8
8

90
80
70
Q1857 R1881 R1882
C1869
C1870
C1868
E

R1866 50 45 40 35 30

C1865

C1866
C1867
25
R1884 R1943 R1941
R1886

R1944
55

Q1858

20
C1941

R1942
R1883
7

7
R1885
E

60
60

Q1859

15
R1867 IC1802 R1901
E

R1868
65

10
Q1867 C1859

FH-X700BT/XNUC
70
C1861

5
C1856 C1804 Q1866 R1902
R1918 R1905 C1860

75
Q1868

1
C1858 80 85 90 95 100 X1801 E
50

R1899
R1900

R1876
C1857 R1919 E
Q1870
R1906
E

1
R1873 R1903
R1809
R1872 R1877 R1904
Q1871
E

C1805
Q1869

C1803
C1801
40
E

R1810
R1875
C1802 Q1855

D1801
1

C1862
C1864

C1863
E
Q1856
R1907

E
R1920 R1874

R1865

R1862 R1863
C1914
Q1854
R1824 Q1852

E
C1915
30

E
D1912 D1911 R1825
L1911

R1864
R1911 C1825
C1913 1 Q1853
6

6
R1912 IC1851 R1860
C1911
R1861

E
10

5
C1912 C1872 R1859
L1801

C1855
C1854
C1873 R1858 Q1851

1
C1871 R1856 R1857
E 20

R1852
R1853
R1851
L1803 R1854 R1855
D1921 R1922
1 C1922
R1921
D1922 L1802 R1932 D1931
15 5 1

C1851
C1923

C1852
C1853
C1921 R1931 D1932
D1923
CN1931 10
KEYBOARD UNIT

R1923 L1804
20 10
Y
0
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
X

5
5

B
 1 2 3 4

11.3 CD CORE UNIT (S11.6STD)

C CD CORE UNIT (S11.6STD) SIDE A

A

PICKUP UNIT(P10.6)(SERVICE)

60
B

TH201 R254 M2
C235 LOADING/CARRIAGE
CN101 R246
1 MOTOR
R232

15 10 5 1
C102
HOME
S901
C201
50 D101

F CN702 R253
10

R245
1 5

E
C238
C
C240 R706
C710
C205 R297
C299
40
C707 C705
C220 R701 R702

M1
SPINDLE
MOTOR

30
D

CN701
15 10 5 1
A
CN701
C702
20 C307

R710
C701 C308
C312
REFO1
R303
R304
R306
R201
R308

E
10 5 1
IC301

10
15 20 25

C306
R301
R264

R302
R307
R305
R202

R309

0
F 10 20 30 40 50
X

C
FH-X700BT/XNUC
62
1 2 3 4
 5 6 7 8

C CD CORE UNIT (S11.6STD) SIDE B

A

60

R102
R101
R103
C104 B

Q102
R108
Q101
E
C202
E
X201
1
R109 50
R294

C203
C239
C209 C225
C233 C110 C101
R237 25 20 15 10 5 1 C224 C111
C210

100
R296 C223 C

C229
C236
C211
30

Q201

95
E
R240
40
R293 R282
35

90
C284 R283 R281 C204
C222
IC201
40

C281 C218
C301 R292

85
C282 R216 R218
C219
R291 R229 C217
45

C283
80
C216 C228
C221 R217
50

55 60 65 70 75
30
R215
R214

R709 C212 C215

D
R260 R708 S905 1
C708
C213
C214

20

E
C703
R711

R313 1
R312 DSCSNS
C303
C302
C304
C305

R311 S903 10
C314
C315

R310
C313

0
50 40 30 20 10 F
X

C
FH-X700BT/XNUC
5 6 7 8
63
 1 2 3 4

11.4 BT UNIT

D BT UNIT SIDE A
A

CN23
10 R38

A CN971 1 5 15
R39

R27

R28
C34

C35

40
R40
C37
R41
BT MODULE
D22
20 15

CN21
R32
C21

C31
D21
D27 1 5 10
C36 R33
R34

30
R29 R30
C25

C26

B
C23
IC22

20
C28

C29

C38

10
5
IC21
C32
C33

C22

C 1

X
C24

C39

0
Y
50

40

30

20

10
D
50

40

30

20

BT UNIT 10 SIDE B

0
D

X
10
20

E
30
40

D
FH-X700BT/XNUC
64
1 2 3 4
 5 6 7 8

12. ELECTRICAL PARTS LIST

NOTE:
Parts whose parts numbers are omitted are subject to being not supplied. A

The part numbers shown below indicate chip components.

Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
The expression of the unit in this manual is shown by u instead of µ. Please do not make a mistake.
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
IC 601 (A,110,77) IC R5S726A0D216FP
A:FH-X700BT/XNUC IC 671 (A,131,75) IC S-80827CNMC-B8M
B:FH-X700BT/XNEW5 IC 681 (A,114,94) Flash ROM Unit(A) PEB040A8
(A,114,94) Flash ROM Unit(B,C,D) PEB039A8
C:FH-X755BT/XNES IC 801 (A,104,18) L-MOS And Gate TC7SET08FUS1
C
D:FH-X759BT/XNID IC 911 (A,145,28) Regulator IC BA49183-V12
IC 961 (A,131,110) IC TPD1052F
Unit Number : QWM3544(A) Q 251 (A,13,130) Chip Transistor RN1910
Q 252 (A,23,131) Chip Transistor RN1910
Unit Number : QWM3543(B) Q 301 (A,87,125) Chip Transistor RN4983
Unit Number : QWM3545(C)
Q 302 (A,127,104) Transistor LTC014YEB
Unit Number : QWM3546(D) Q 531 (A,93,97) Transistor LSAR523UB
Q 601 (A,93,68) Transistor LTC014YEB
Unit Name : Tuner Amp Unit Q 751 (A,142,139) Transistor 2SD2396
Q 752 (A,142,133) Chip Transistor RN4983
Unit Number :
Q 871 (A,144,59) Transistor 2SA1577 D
Unit Name : Keyboard Unit Q 872 (A,144,67) Transistor LTC143EUB
Unit Number : QWM3533 Q 941 (A,96,121) Transistor LSCR523UB
D 301 (A,102,125) Diode CRG03
Unit Name : BT Unit D 302 (A,90,121) Diode CRG03

Unit Number : CWX4023 D 401 (A,158,107) Diode RN731VN

D 402 (A,158,100) Diode RN731VN
Unit Name : CD Core Unit (S11.6STD) D 551 (A,22,124) Diode CMS03
D 552 (A,22,104) Diode RB056L-40
D 751 (A,138,135) Diode RKZ8.2KG(B2)

A
Unit Number : QWM3544(A)
D
D
803
804
(A,126,15)
(A,119,14)
Diode
Diode
DZ2S068C
DZ2S068C E

Unit Number : QWM3543(B) D 805 (A,120,14) Diode DZ2S068C

D 806 (A,116,13) Diode DZ2S068C
Unit Number : QWM3545(C) D 807 (A,113,13) Diode DZ2S068C
Unit Number : QWM3546(D)
D 901 (A,141,127) Diode 1SR154-400
Unit Name : Tuner Amp Unit D 902 (A,137,127) Diode 1SR154-400
D 911 (A,158,66) Diode CRG03
MISCELLANEOUS D 912 (A,161,66) Diode CRG03
D 941 (A,93,125) Diode(A,C,D) HZU7L(A1)
IC 201 (A,101,107) LSI PM9013A (A,93,125) Diode(B) HZU7L(C3)
IC 301 (A,78,142) IC PA2030A
IC 401 (A,150,91) IC TDA7706 L 202 (A,94,102) Inductor CTF1793 F
IC 531 (A,93,88) IC 337S3959 L 401 (A,155,104) Chip Coil LCTAWR27J2520
IC 551 (A,19,111) Regulator IC BD9876EFJ L 402 (A,159,104) Chip Coil LCTAWR15J2520
L 403 (A,151,102) Inductor CTF1786
IC 552 (A,106,24) IC BD2232G-G L 404 (A,146,102) Inductor CTF1786
FH-X700BT/XNUC
5 6 7 8
65
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
(A,138,91) (C,D) RS1/16SS391J
L 405 (A,151,108) Inductor(A) LCYB68NJ1608 R 412 (A,152,78) RS1/4SA8R2J
L 406 (A,147,105) Inductor(A,B) CTF1389 R 413 (A,158,78) RS1/4SA8R2J
L 407 (A,147,107) Chip Coil(C,D) LCTAWR27J2520 R 414 (A,139,87) RS1/16SS0R0J
A
L 408 (A,141,104) Chip Coil(A,B) LCTAW4R7J2520 R 415 (A,152,80) (A,C,D) RS1/16SS0R0J
(A,141,104) Chip Coil(C,D) LCTAW1R5J2520
R 531 (A,91,94) RS1/16SS473J
L 409 (A,143,109) Chip Coil(C,D) LCTAWR39J2520 R 532 (A,91,85) RS1/16SS222J
L 410 (A,137,94) Chip Coil(A,B) LCTAW470J2520 R 533 (A,92,85) RS1/16SS222J
(A,137,94) Inductor(C,D) LCTAW2R2J2520 R 534 (A,93,92) RS1/16SS272J
L 413 (A,144,82) Inductor CTF1786 R 535 (A,95,92) RS1/16SS472J
L 414 (A,153,80) Inductor(B) CTF1786
R 536 (A,96,92) RS1/16SS472J
L 419 (A,161,95) Inductor CTF1786 R 537 (A,96,85) RS1/16SS101J
L 420 (A,161,96) Inductor CTF1786 R 538 (A,95,84) RS1/16SS101J
L 551 (A,30,107) Inductor CTH1524 R 551 (A,25,111) RS1/16SS682J
B L 801 (A,115,17) Inductor CTF1713 R 552 (A,30,112) RS1/16SS0R0J
L 901 (A,112,141) Choke Coil 600 uH CTH1432
R 553 (A,27,112) RS1/16SS1803D
X 401 (A,161,88) Crystal Resonator 36.48 MHz CSS1848 R 554 (A,27,110) RS1/16SS4302D
X 601 (A,126,76) Crystal Resonator 12 MHz CSS1847 R 555 (A,39,124) RS1/10SR471J
X 603 (A,123,92) Resonator 16.93 MHz CSS1794 R 601 (A,101,66) RS1/16SS473J
>P251 (A,6,130) Fuse 3.0 A CEK1386 R 602 (A,107,63) RS1/16SS473J
P 402 (A,155,111) Surge Absorber HSPC16701B02
R 603 (A,109,62) RS1/16SS473J
CN701 (A,114,32) Connector VKN1192 R 609 (A,122,64) RS1/16SS473J
CN801 (A,109,4) Connector CKS6452 R 610 (A,122,70) RS1/16SS473J
CN971 (A,93,49) Connector VKN1192 R 611 (A,124,72) RS1/16SS473J
JA251 (A,19,138) Pin Jack CKB1099 R 613 (A,121,76) RS1/16SS152J
C JA401 (A,158,129) Antenna Jack YKS5041
R 614 (A,122,78) RS1/16SS473J
JA892 (A,42,141) Jack YKS5035 R 615 (A,130,79) RS1/16SS473J
JA901 (A,113,141) Connector CKM1613 R 616 (A,125,68) RS1/16SS473J
Fuse 10 A YEK5001 R 617 (A,131,81) RS1/16SS103J
R 618 (A,125,82) (A) RS1/16SS103J
RESISTORS (A,125,82) (B,D) RS1/16SS473J
(A,125,82) (C) RS1/16SS223J
R 251 (A,18,131) RS1/16SS821J
R 252 (A,9,132) RS1/16SS821J R 619 (A,126,82) (A,C,D) RS1/16SS473J
R 253 (A,15,131) RS1/16SS223J (A,126,82) (B) RS1/16SS223J
R 254 (A,11,131) RS1/16SS223J R 622 (A,125,87) RS1/16SS473J
R 255 (A,29,132) RS1/16SS821J R 623 (A,130,85) RAB4CQ473J
D R 624 (A,120,89) RS1/16SS222J
R 256 (A,19,131) RS1/16SS821J R 625 (A,114,90) RS1/16SS101J
R 257 (A,28,131) RS1/16SS223J
R 258 (A,21,131) RS1/16SS223J R 626 (A,113,90) RS1/16SS101J
R 301 (A,68,127) RS1/16SS471J R 627 (A,112,88) RS1/16SS101J
R 302 (A,82,125) RS1/16SS471J R 628 (A,111,90) RS1/16SS101J
R 629 (A,109,92) RS1/16SS101J
R 303 (A,73,127) RS1/16SS471J R 630 (A,110,89) RS1/16SS101J
R 304 (A,78,126) RS1/16SS471J
R 305 (A,88,127) RS1/16SS103J R 631 (A,107,92) RS1/16SS473J
R 306 (A,89,129) RS1/16SS102J R 632 (A,105,91) RS1/16SS473J
R 309 (A,86,121) RS1/16SS103J R 633 (A,107,90) RS1/16SS101J
R 634 (A,103,88) RS1/16SS102J
E
R 311 (A,86,123) RS1/16SS473J R 635 (A,102,88) RS1/16SS102J
R 312 (A,99,129) RS1/16SS103J
R 401 (A,161,106) RS1/16SS221J R 636 (A,100,91) RS1/16SS473J
R 402 (A,161,100) RS1/16SS751J R 637 (A,100,90) RS1/16SS473J
R 403 (A,139,104) (A,B) RS1/16SS391J R 638 (A,104,92) RS1/16SS473J
(A,139,104) (C,D) RS1/16SS331J R 639 (A,97,91) RS1/16SS472J
R 640 (A,98,91) RS1/16SS472J
R 404 (A,142,99) RS1/16SS105J
R 406 (A,154,108) RS1/16SS105J R 643 (A,99,82) RS1/16SS104J
R 407 (A,139,96) RS1/16SS330J R 644 (A,98,79) RS1/16SS101J
R 408 (A,137,97) (A,B) RS1/16SS471J R 645 (A,95,79) RS1/16SS101J
(A,137,97) (C,D) RS1/16SS361J R 646 (A,92,75) RS1/16SS103J
F R 409 (A,144,98) (C,D) RS1/16SS0R0J R 647 (A,98,78) RS1/16SS101J
R 410 (A,141,91) RS1/16SS0R0J
R 648 (A,95,76) RS1/16SS102J
R 411 (A,138,91) (A,B) RS1/16SS681J R 649 (A,95,75) RS1/16SS102J
R 650 (A,95,74) RS1/16SS102J
FH-X700BT/XNUC
66
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 651 (A,97,71) RS1/16SS473J R 943 (A,95,125) (A,C,D) RS1/16SS472J
R 652 (A,98,69) RS1/16SS222J (A,95,125) (B) RS1/16SS473J
R 944 (A,98,123) RS1/4SA102J
R 653 (A,100,66) RS1/16SS103J A
R 659 (A,123,61) RS1/16SS153J R 961 (A,127,112) RS1/16SS103J
R 660 (A,123,60) RS1/16SS153J R 962 (A,130,113) RS1/16SS103J
R 664 (A,133,62) RS1/16SS103J R 963 (A,129,112) RS1/16SS105J
R 668 (A,93,71) RS1/16SS473J R 973 (A,90,63) RS1/16SS0R0J
R 974 (A,98,55) RS1/16SS101J
R 669 (A,95,69) RS1/16SS473J
R 671 (A,128,70) RS1/16SS104J R 975 (A,98,54) RS1/16SS101J
R 681 (A,109,97) RS1/16SS473J R 976 (A,98,52) RS1/16SS101J
R 682 (A,110,91) RS1/16SS473J
R 683 (A,120,92) RS1/16SS473J CAPACITORS
R 684 (A,109,94) RS1/16SS473J C 201 (A,96,115) CKSRYB105K10
R 685 (A,120,96) RS1/16SS473J C 202 (A,104,116) CKSRYB105K10 B
R 701 (A,108,38) RS1/16SS473J C 203 (A,92,116) CKSRYB105K10
R 702 (A,115,37) RS1/16SS104J C 204 (A,107,115) CKSRYB105K10
R 703 (A,118,28) RAB4CQ472J C 205 (A,94,116) CKSRYB105K10

R 704 (A,110,41) RS1/16SS104J C 206 (A,107,114) CKSRYB105K10

R 706 (A,108,36) RS1/16SS221J C 207 (A,94,108) CKSSYB104K10
R 707 (A,109,38) RS1/16SS221J C 208 (A,94,106) CKSSYB104K10
R 708 (A,110,38) RS1/16SS101J C 209 (A,93,104) 10 uF CCG1192
R 709 (A,111,38) RS1/16SS221J C 210 (A,96,106) CCSSCH151J50

R 710 (A,112,38) RS1/16SS101J C 211 (A,109,107) CCSSCH151J50

R 711 (A,114,39) RS1/16SS102J C 212 (A,108,109) 10 uF CCG1192
R 715 (A,116,36) RS1/16SS151J C 213 (A,108,106) CKSSYB104K10 C
R 716 (A,117,36) RS1/16SS151J C 214 (A,108,104) CKSSYB104K10
R 717 (A,119,36) RS1/16SS151J C 215 (A,108,102) CKSSYB104K10

R 718 (A,122,36) RS1/16SS221J C 216 (A,92,101) 10 uF CCG1192

R 719 (A,121,36) RS1/16SS104J C 217 (A,95,100) CKSSYB104K10
R 752 (A,145,135) RS1/10SR821J C 218 (A,114,109) XCEVW470M16
R 753 (A,127,91) RS1/16SS473J C 219 (A,112,103) 10 uF CCG1192
R 754 (A,127,92) RS1/16SS103J C 220 (A,106,98) 10 uF CCG1192

R 801 (A,124,22) RS1/10SR222J C 223 (A,91,101) CKSSYB102K50

R 802 (A,103,15) RS1/10SR222J C 224 (A,115,103) CKSSYB104K10
R 803 (A,121,17) RS1/16SS223J C 229 (A,110,112) CKSSYB102K50
R 804 (A,118,17) RS1/16SS223J C 236 (A,110,104) CKSRYB105K10 D
R 805 (A,121,19) RS1/10SR101J C 251 (A,35,128) 4.7 uF CCG1201

R 806 (A,118,20) RS1/10SR101J C 252 (A,17,127) 4.7 uF CCG1201

R 807 (A,119,20) RS1/10SR101J C 253 (A,17,130) CCSSCH101J50
R 808 (A,124,20) RS1/10SR222J C 254 (A,10,130) CCSSCH101J50
R 809 (A,115,21) RS1/10SR220J C 255 (A,35,132) 4.7 uF CCG1201
R 810 (A,114,21) RS1/10SR220J C 256 (A,30,130) 4.7 uF CCG1201

R 811 (A,117,20) RS1/10SR222J C 257 (A,26,131) CCSSCH101J50

R 812 (A,112,21) RS1/10SR222J C 258 (A,20,131) CCSSCH101J50
R 813 (A,107,16) RS1/10SR222J C 261 (A,6,133) (A,C) CCSSCH101J50
R 814 (A,101,19) RS1/10SR222J (A,6,133) (B,D) CKSSYB102K50
E
R 815 (A,100,19) RS1/16SS822J C 301 (A,69,129) CKSRYB224K16
C 303 (A,80,129) CKSRYB224K16
R 816 (A,96,19) RS1/10SR222J
R 817 (A,95,19) RS1/10SR222J C 305 (A,72,129) CKSRYB224K16
R 851 (A,93,20) RS1/16SS472J C 307 (A,77,129) CKSRYB224K16
R 871 (A,143,65) RS1/10SR332J C 313 (A,83,130) CKSRYB105K16
R 872 (A,143,62) RS1/16SS103J C 314 (A,135,126) CKSRYB104K16
C 317 (A,60,129) XCEVW100M16
R 877 (A,121,27) RS1/16SS1R0J
R 878 (A,124,26) RS1/10SR473J C 319 (A,62,136) CCSSCH101J50
R 891 (A,58,138) RS1/16SS102J C 320 (A,64,135) CCSSCK1R0C50
R 892 (A,58,136) RS1/16SS102J C 321 (A,83,129) CCSSCH101J50
R 911 (A,145,40) RS1/10SR1R0J C 322 (A,104,126) CKSRYB104K16 F
C 323 (A,106,129) CCSRCH100D50
R 912 (A,141,41) RS1/10SR1R0J
R 941 (A,94,121) RS1/16SS223J C 324 (A,102,129) CCSRCH100D50
R 942 (A,94,122) RS1/16SS473J
FH-X700BT/XNUC
5 6 7 8
67
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 325 (A,95,134) CCSRCH100D50 C 561 (A,102,23) CKSRYB105K10
C 326 (A,93,138) CCSRCH100D50 C 564 (A,32,114) 4.7 uF CCG1201
C 327 (A,87,129) CKSRYB105K16
C 402 (A,155,101) CKSSYB103K16 C 565 (A,15,107) 4.7 uF CCG1222
A
C 601 (A,104,66) CKSSYB104K10
C 403 (A,152,102) CKSRYB105K10 C 602 (A,109,65) CKSSYB104K10
C 405 (A,162,101) CKSSYB103K16 C 603 (A,111,65) CKSSYB104K10
C 406 (A,160,101) CKSSYB103K16 C 604 (A,112,65) CKSSYB104K10
C 408 (A,161,105) CKSSYB103K16
C 409 (A,156,105) CCSSCH6R0D50 C 605 (A,116,65) CKSSYB104K10
C 606 (A,122,71) CKSSYB104K10
C 410 (A,155,107) CCSSCH330J50 C 607 (A,126,73) CCSSCH120J50
C 411 (A,148,99) CKSSYB103K16 C 608 (A,126,78) CCSSCH120J50
C 412 (A,148,101) CKSSYB104K10 C 609 (A,121,73) CKSSYB104K10
C 413 (A,150,101) CKSSYB104K10
C 414 (A,145,100) CKSSYB103K16 C 610 (A,121,75) CKSSYB104K10
B C 611 (A,122,77) CKSSYB104K10
C 415 (A,144,101) 10 uF CCG1192 C 612 (A,122,82) CKSSYB104K10
C 416 (A,147,100) CKSSYB104K10 C 613 (A,123,82) CKSSYB104K10
C 418 (A,142,101) CKSSYB223K16 C 618 (A,123,89) CCSSCH120J50
C 419 (A,146,110) (C,D) CCSSCH150J50
C 619 (A,123,94) CCSSCH120J50
C 420 (A,150,106) (B,C,D) CKSSYB103K16 C 620 (A,114,88) CKSSYB104K10
C 421 (A,154,111) (A) CCSSCJ3R0C50 C 621 (A,108,88) CKSSYB104K10
C 423 (A,144,106) (C,D) CCSSCH8R0D50 C 622 (A,105,93) CCSSCH220J50
C 424 (A,140,101) CKSSYB103K16 C 623 (A,106,88) CKSSYB104K10

C 425 (A,138,99) 10 uF CCG1192 C 624 (A,105,88) CKSSYB104K10

C 426 (A,139,97) CKSSYB104K10 C 625 (A,104,90) CKSSYB104K10
C C 427 (A,144,97) CKSSYB104K10 C 626 (A,100,80) CKSSYB104K10
C 428 (A,137,96) (A,B) CCSSCH101J50 C 627 (A,97,81) CCSSCH220J50
(A,137,96) (C,D) CCSSCH220J50 C 628 (A,95,81) CCSSCH220J50
C 429 (A,136,96) CKSSYB103K16
C 629 (A,99,75) CKSSYB104K10
C 430 (A,139,90) 1 uF(A) DCH1246 C 630 (A,99,73) CKSSYB104K10
C 432 (A,138,92) (A,B) CCSSCH820J50 C 631 (A,96,77) CCSSCH220J50
(A,138,92) (C,D) CCSSCK2R0C50 C 672 (A,132,71) CKSRYB105K10
C 433 (A,136,91) 1 uF(A) DCH1246 C 681 (A,121,96) CKSSYB104K10

C 435 (A,139,86) CKSRYB474K10 C 683 (A,120,94) CCSSCJ3R0C50

C 436 (A,140,84) (C,D) CKSSYB104K10 C 701 (A,111,41) CKSSYB103K16
C 439 (A,145,80) (C,D) CKSRYB104K16 C 704 (A,120,39) CCSSCH100D50
D C 440 (A,142,86) CKSSYB102K50 C 705 (A,118,38) CCSSCH100D50
C 706 (A,116,38) CCSSCH100D50
C 441 (A,137,89) (A) CCSSCH100D50
C 442 (A,146,83) CKSSYB104K10 C 752 (A,141,135) CKSSYB104K10
C 444 (A,152,82) 2.2 uF CCG1218 C 753 (A,147,131) 10 uF CCG1192
C 445 (A,156,82) CKSSYB104K10 C 807 (A,122,14) CKSRYB105K10
C 447 (A,157,83) 2.2 uF(C,D) CCG1218 C 808 (A,108,19) CKSRYB104K16
C 448 (A,158,85) (A,B) CKSSYB104K10 C 811 (A,104,20) CKSSYB104K10

C 449 (A,161,85) CCSSCH9R0D50 C 873 (A,124,24) CKSRYB104K16

C 450 (A,161,90) CCSSCH9R0D50 C 891 (A,52,138) CKSRYB104K16
C 451 (A,158,91) CKSSYB104K10 C 892 (A,34,139) CKSRYB104K16
C 452 (A,158,94) CKSRYB105K10 C 893 (A,34,135) CKSRYB102K50
E
C 453 (A,160,96) CKSSYB104K10 C 894 (A,52,134) CKSRYB102K50

C 455 (A,158,97) CKSRYB224K16 C 901 (A,133,124) 2 200 uF/16 V CCH2040

C 456 (A,161,92) CKSSYB472K25 C 912 (A,152,40) CKSSYB102K50
C 457 (A,161,93) CKSSYB472K25 C 913 (A,131,43) CKSSYB102K50
C 461 (A,145,104) CKSSYB104K16 C 914 (A,156,56) 1 000 uF/16 V CCH2024
C 531 (A,91,93) CKSSYB104K10 C 915 (A,132,42) CKSRYB104K16

C 532 (A,93,93) CKSSYB104K10 C 916 (A,146,43) 4.7 uF CCG1201

C 551 (A,13,121) XCEVW221M16 C 917 (A,145,46) CKSSYB102K50
C 552 (A,13,107) CKSRYB105K16 C 919 (A,151,42) 4.7 uF CCG1201
C 553 (A,15,110) CKSSYB103K16 C 921 (A,135,42) 4.7 uF CCG1201
F
C 555 (A,25,112) CKSSYB682K25 C 923 (A,159,41) 4.7 uF CCG1201

C 556 (A,32,120) CEVQW221M6R3 C 926 (A,140,44) 4.7 uF CCG1201

C 557 (A,32,116) CKSRYB105K10 C 927 (A,139,42) CKSSYB102K50
C 560 (A,108,21) CKSRYB105K10 C 941 (A,96,124) CKSRYB104K16
FH-X700BT/XNUC
68
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 961 (A,126,107) CKSSYB104K16
C 962 (A,132,107) CKSSYB104K16 RESISTORS
C 966 (A,128,112) CKSSYB333K16 R 1809 (B,79,44) RS1/10SR473J A
C 969 (A,135,113) 22 uF DCH1256 R 1810 (B,68,42) RS1/10SR103J
C 973 (A,98,53) CCSSCH470J50 R 1824 (B,67,31) RS1/10SR273J
R 1851 (B,64,18) RS1/10SR222J

B
Unit Number :
R

R
1852

1853
(B,63,18)

(B,61,18)
RS1/10SR222J

RS1/10SR222J
Unit Name : Keyboard Unit R 1854 (B,44,17) RS1/10SR102J
R 1856 (B,45,19) RS1/10SR102J
R 1858 (B,51,21) RS1/10SR102J
MISCELLANEOUS R 1860 (B,51,26) RS1/10SR102J

IC 1802 (B,83,58) IC PDC202B R 1862 (B,54,29) RS1/10SR102J

IC 1851 (B,61,23) IC BH2228FV R 1864 (B,56,29) RS1/10SR102J B
IC 1941 (A,25,74) Remote IC GP1UXC14RK R 1866 (B,139,65) RS1/10SR101J
Q 1851 (B,32,20) Transistor LSCR523UB R 1867 (B,149,58) RS1/10SR101J
Q 1852 (B,35,30) Transistor LSCR523UB R 1868 (B,127,56) RS1/10SR101J

Q 1853 (B,42,26) Transistor LSCR523UB R 1872 (B,100,43) RS1/10SR101J

Q 1854 (B,50,31) Transistor LSCR523UB R 1873 (B,114,46) RS1/10SR101J
Q 1855 (B,50,38) Transistor LSCR523UB R 1874 (B,106,34) RS1/10SR101J
Q 1856 (B,59,36) Transistor LSCR523UB R 1875 (B,43,39) RS1/10SR101J
Q 1857 (B,147,66) Transistor LSCR523UB R 1876 (B,28,49) RS1/10SR101J

Q 1858 (B,153,60) Transistor LSCR523UB R 1877 (B,51,44) RS1/10SR101J

Q 1859 (B,140,58) Transistor LSCR523UB R 1881 (B,142,67) RS1/10SR680J
Q 1866 (B,38,52) Transistor LSCR523UB R 1882 (B,139,67) RS1/10SR0R0J C
Q 1867 (B,31,55) Transistor LSCR523UB R 1883 (B,147,61) RS1/10SR680J
Q 1868 (B,44,50) Transistor LSCR523UB R 1884 (B,147,62) RS1/10SR0R0J

Q 1869 (B,112,40) Transistor LSCR523UB R 1885 (B,142,61) RS1/10SR680J

Q 1870 (B,120,48) Transistor LSCR523UB R 1886 (B,142,62) RS1/10SR0R0J
Q 1871 (B,105,41) Transistor LSCR523UB R 1899 (B,32,49) RS1/10SR680J
D 1882 (A,153,49) LED SMLVN6RGB2U(A) R 1900 (B,31,49) RS1/10SR0R0J
D 1883 (A,16,49) LED SMLVN6RGB2U(A) R 1901 (B,27,58) RS1/10SR680J

D 1884 (A,118,24) LED SMLVN6RGB2U(A) R 1902 (B,25,53) RS1/10SR0R0J

D 1885 (A,35,70) LED MSL0101RGBU R 1903 (B,48,46) RS1/10SR680J
D 1886 (A,134,71) LED MSL0101RGBU R 1904 (B,48,44) RS1/10SR0R0J
D 1887 (A,51,24) LED SMLVN6RGB2U(A) R 1905 (B,105,52) RS1/10SR680J D
L 1802 (B,133,13) Inductor CTF1389 R 1906 (B,107,48) RS1/10SR680J

L 1803 (B,131,17) Inductor CTF1389 R 1907 (B,111,36) RS1/10SR680J

L 1804 (B,131,10) Inductor CTF1389 R 1918 (B,108,52) RS1/10SR0R0J
X 1801 (B,70,49) Ceramic Resonator 5.00 MHz CSS1547 R 1919 (B,107,49) RS1/10SR0R0J
S 1821 (A,51,20) Push Switch CSG1155 R 1920 (B,111,34) RS1/10SR0R0J
S 1822 (A,15,93) Push Switch CSG1155 R 1931 (B,86,11) RS1/10SR222J

S 1823 (A,118,20) Push Switch CSG1155 R 1932 (B,86,13) RS1/10SR222J

S 1824 (A,58,9) Push Switch CSG1155 R 1944 (B,31,61) RS1/10SR101J
S 1826 (A,18,43) Push Switch CSG1155
S 1828 (A,110,39) Push Switch CSG1155
CAPACITORS E
S 1830 (A,85,24)Encoder(MULTI-CONTROL) CSD1168
C 1801 (B,83,41) CKSRYB104K16
S 1832 (A,111,9) Push Switch CSG1155
C 1802 (B,83,40) CKSRYB104K16
S 1834 (A,130,53) Push Switch CSG1155
C 1803 (B,86,40) CKSRYB104K16
S 1835 (A,120,53) Push Switch CSG1155
C 1804 (B,69,53) CKSRYB105K10
S 1836 (A,89,53) Push Switch CSG1155
C 1805 (B,73,43) CKSRYB104K16
S 1837 (A,96,53) Push Switch CSG1155
C 1851 (B,64,11) CCSRCH100D50
S 1838 (A,58,53) Push Switch CSG1155
C 1852 (B,62,11) CCSRCH100D50
S 1839 (A,65,53) Push Switch CSG1155
C 1853 (B,60,11) CCSRCH100D50
S 1840 (A,34,53) Push Switch CSG1155
C 1854 (B,68,21) CKSRYB103K50
S 1842 (A,59,39) Push Switch CSG1155
C 1855 (B,66,21) CKSRYB105K10
CN1911 (A,150,33) Connector CKS6443
F
C 1911 (B,140,27) CKSRYB104K16
CN1931 (B,109,10) Connector CKS6451
C 1912 (B,136,24) CKSRYB104K16
JA1921 (A,151,16) Jack CKN1094
C 1941 (B,28,61) 10 uF CCG1192
V 1802 (A,40,80) Segment LCD CAW2025

FH-X700BT/XNUC
5 6 7 8
69
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 217 (B,10,32) RS1/16SS562J

D
Unit Number : QWM3533
R
R
R
218
229
232
(B,10,35)
(B,12,34)
(A,31,54)
RS1/16SS472J
RS1/16SS471J
RS1/16SS0R0J
A
R 237 (B,33,45) RS1/16SS221J
Unit Name : BT Unit
R 240 (B,34,40) RS1/16SS473J
MISCELLANEOUS R 245 (A,34,46) RS1/16SS104J
R 254 (A,37,56) RS1/16SS104J
IC 21 (A,8,48) Regulator IC S-1172B18-E6 R 260 (B,30,27) RS1/16SS103J
IC 22 (A,21,46) IC S-1206B33-U3 R 264 (A,22,9) RS1/16SS102J
CN21 (A,34,27) Connector CKS6346
CN23 (A,42,44) Connector CKS3857 R 281 (B,33,38) RS1/16SS560J
R 282 (B,33,39) RS1/16SS560J
RESISTORS R 283 (B,35,38) RS1/16SS0R0J
R 291 (B,33,34) RS1/16SS560J
B R 28 (A,42,31) RS1/10SR102J R 292 (B,33,36) RS1/16SS0R0J
R 29 (A,30,41) RS1/10SR102J
R 30 (A,30,37) RS1/10SR102J R 293 (B,35,39) RS1/16SS0R0J
R 38 (A,42,17) RS1/10SR0R0J R 294 (B,27,48) RS1/16SS471J
R 39 (A,41,23) RS1/10SR221J R 296 (B,34,43) RS1/16SS0R0J
R 301 (A,27,9) RS1/16SS0R0J
R 40 (A,40,23) RS1/10SR221J R 302 (A,28,9) RS1/16SS0R0J
R 41 (A,38,23) RS1/10SR221J
R 303 (A,27,11) RS1/16SS123J
CAPACITORS R 304 (A,28,11) RS1/16SS123J
R 305 (A,26,9) RS1/16SS102J
C 23 (A,24,40) Capacitor CEVW221M4 R 306 (A,26,11) RS1/16SS472J
C 24 (A,7,44) CKSRYB105K10 R 307 (A,25,9) RS1/16SS102J
C C 26 (A,27,48) 10 uF CCG1192
C 29 (A,17,45) CKSRYB105K10 R 308 (A,25,11) RS1/16SS472J
C 33 (A,9,54) 10 uF CCG1192 R 309 (A,35,6) RS1/16SS473J
R 310 (B,30,9) RS1/16SS472J
C 34 (A,42,30) CKSRYB105K10 R 311 (B,30,10) RS1/16SS472J
C 36 (A,32,40) CKSRYB104K16 R 312 (B,30,11) RS1/16SS472J
C 38 (A,15,46) 10 uF CCG1192
C 39 (A,6,42) 10 uF CCG1192 R 313 (B,30,12) RS1/16SS472J
R 701 (A,21,38) RS1/16SS101J
R 702 (A,23,38) RS1/16SS101J
C
Unit Number : CWX4023
R
R
706
708
(A,32,42)
(B,28,26)
RS1/16SS221J
RS1/16SS0R0J

D Unit Name : CD Core Unit (S11.6STD) R 709 (B,29,28) RS1/16SS0R0J

MISCELLANEOUS CAPACITORS

IC 201 (B,23,37) IC PE5791A C 104 (B,12,57) CKSQYB475K6R3

IC 301 (A,37,11) IC BD8223EFV C 203 (B,22,47) CKSSYB104K10
Q 101 (B,11,53) Transistor 2SA1577 C 209 (B,28,47) CKSRYB104K16
Q 102 (B,15,54) Transistor LTA123JUB C 210 (B,33,43) CKSSYB104K10
X 201 (B,25,49) Ceramic Resonator 16.934 MHz CSS1603 C 211 (B,33,41) CKSSYB104K10

S 901 (A,42,53) Spring Switch(HOME) CSN1080 C 212 (B,22,28) CKSSYB104K10

S 903 (B,21,12) Spring Switch(DSCSNS) CSN1081 C 213 (B,18,26) CKSSYB332K50
CN101 (A,16,58) Connector CKS4808 C 214 (B,17,26) CKSSYB473K16
E
CN701 (A,25,29) Connector CKS6146 C 215 (B,19,28) CKSSYB104K10
C 216 (B,12,33) CKSSYB182K50
RESISTORS
C 217 (B,10,34) CCSSCH560J50
R 101 (B,6,57) RS1/10SR2R4J C 218 (B,10,36) CCSSCH4R0C50
R 102 (B,8,57) RS1/10SR2R4J C 219 (B,14,34) CKSSYB104K10
R 103 (B,9,57) RS1/10SR2R7J C 220 (A,18,38) CKSSYB104K10
R 108 (B,18,55) RS1/16SS105J C 221 (B,14,32) CKSSYB104K10
R 109 (B,12,50) RS1/16SS222J
C 222 (B,13,37) CKSSYB104K10
R 201 (A,24,11) RS1/16SS0R0J C 223 (B,12,42) CCSSCH680J50
R 202 (A,23,9) RS1/16SS0R0J C 224 (B,13,45) CCSSCH470J50
F R 214 (B,18,28) RS1/16SS103J C 225 (B,13,46) CKSSYB103K16
R 215 (B,17,28) RS1/16SS393J C 228 (B,10,33) CCSSCH270J50
R 216 (B,12,35) RS1/16SS122J
C 229 (B,9,40) CKSSYB104K10

FH-X700BT/XNUC
70
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No.
C 233 (B,32,46) CKSSYB103K16
C 236 (B,8,40) CKSSYB104K10
C 238 (A,25,44) CKSRYB104K16
C 299 (A,26,41) CKSSYB104K10 A

C 302 (B,28,12) CKSSYB102K50

C 303 (B,29,12) CKSSYB102K50
C 304 (B,27,12) CKSSYB223K16
C 305 (B,26,12) CKSSYB104K10
C 306 (A,31,7) CKSSYB104K10

C 307 (A,41,19) CKSRYB105K10

C 308 (A,31,15) CKSRYB105K10
C 710 (A,34,42) CKSSYB102K50

FH-X700BT/XNUC
5 6 7 8
71