Installation Manual

INMARSAT-1 MES
Model FELCOM18

SAFETY INSTRUCTIONS ................................................................................................ i

SYSTEM CONFIGURATION ........................................................................................... ii
EQUIPMENT LISTS........................................................................................................ iii

1. MOUNTING..............................................................................................................1-1
1.1 Antenna Unit ......................................................................................................................1-1
1.2 Terminal Unit......................................................................................................................1-3
1.3 Distress Alert/Received Call Unit IC-305/Alarm Unit IC-306..............................................1-5
1.4 Printer (option) ...................................................................................................................1-6
1.5 AC/DC Power Supply Unit PR-240 (option).......................................................................1-7
1.6 Junction Box IC-318...........................................................................................................1-8

2. WIRING....................................................................................................................2-1
2.1 Antenna Cable Connector at the Terminal Unit .................................................................2-2
2.2 Distress Alert/Received Call Unit IC-305 ...........................................................................2-5
2.3 Alarm Unit IC-306 ..............................................................................................................2-5
2.4 Junction Box IC-318...........................................................................................................2-6

3. INITIAL SETTINGS..................................................................................................3-1
3.1 How to Set the IMN (INMARSAT MOBILE NO.)................................................................3-1
3.2 How to Set External Equipment .........................................................................................3-2
3.3 How to Set the Alarm Contact............................................................................................3-3
3.4 How to Set up the AMS/BAM.............................................................................................3-3
3.5 How to Select Position-fixing Equipment ...........................................................................3-6
3.6 How to Set up for 2nd DTE ................................................................................................3-6
3.7 How to Set the Russian Language ....................................................................................3-7
3.8 How to Use the Paper Save Function................................................................................3-7

4. HOW TO INSTALL OPTIONAL EQUIPMENT ........................................................4-1

4.1 GPS Board OP16-62 .........................................................................................................4-1
4.2 IPX2 Kit OP16-58/OP16-59 ...............................................................................................4-2
4.3 Waterproofing Kit OP16-60/OP16-67/OP16-68 .................................................................4-7

5. HOW TO CHANGE POWER SUPPLY SPECIFICATIONS.....................................5-1

APPENDIX 1 JIS CABLE GUIDE .............................................................................AP-1
PACKING LISTS ......................................................................................................... A-1
OUTLINE DRAWINGS ................................................................................................ D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1

www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
 7KHSDSHUXVHGLQWKLVPDQXDO
LVHOHPHQWDOFKORULQHIUHH

࣭)85812$XWKRUL]HG'LVWULEXWRU'HDOHU

$VKLKDUDFKR
1LVKLQRPL\D-$3$1

$OOULJKWVUHVHUYHG 3ULQWHGLQ-DSDQ $  -81  

-  -81  
3XE1R ,0(-
(70,  )(/&20


 SAFETY INSTRUCTIONS

WARNING CAUTION
Do not open the equipment
unless totally familiar with Confirm that the power supply
electrical circuits and voltage is compatible with the
service manual. voltage rating of the equipment.

Connection to the wrong power

ELECTRICAL Only qualified personnel supply can cause fire or equipment
SHOCK should work inside the damage. The voltage rating appears
HAZARD equipment. on the label at the rear of the
terminal unit.
Do not approach the ra-
dome closer than 0.5 m Use the correct fuse.
when it is transmitting.
Use of wrong fuse can result in
Microwave radiation can damage to the equipment.
cause severe injury or illness.
Radiation level:
2
10 W/m at 0.5 m Keep the following compass
safe distances.

Turn off the power at the Standard Steering

mains switchboard before Antenna Unit IC-118 0.30 m 0.30 m
beginning the installation. Terminal Unit IC-218 0.65 m 0.40 m
Post a sign near the switch
Printer PP-510 or PP-520 1.00 m 0.80 m
to indicate it should not be
Junction Box IC-318 0.90 m 0.60 m
turned on while the equip-
Distress Alert/
ment is being installed. 0.50 m 0.30 m
Received Call Unit IC-305
Fire, electrical shock or Alarm Unit IC-306 0.50 m 0.30 m
serious injury can result if the SSAS Alert Unit IC-307 0.70 m 0.45 m
power is left on or is applied AC/DC Power Supply Unit
0.90 m 0.60 m
while the eqiuipment is being PR-240
installed. Mini keyboard 0.30 m 0.30 m

Ground the equipment to prevent

electrical shock and mutual
interface.

i
SYSTEM CONFIGURATION
Standard configuration is shown with solid line.

ANTENNA
UNIT IC-118

DGPS

TERMINAL UNIT
POWER SUPPLY IC-218
100-115/200-230 VAC ,
1φ 50/60 Hz AC/DC Power Supply Personal Computer
POWER SUPPLY PR-240 (PC/AT compatible)
24 VDC
Built in
POWER SUPPLY GPS Board Shipboard LAN (Ethernet)
12/24 VDC OP16-62
Printer**
POWER SUPPLY PP-510/
24 VDC PP-520
For 12 VDC power supply,
DC-DC converter is Mini Keyboard
Distress Alert/
required to use PP-510 or 5139U or 5139U BLACK
Received Call Unit
PP-520. IC-305 or 350

SSAS Alert Unit* SSAS Alert Unit* JUNCTION

IC-307 IC-307 BOX IC-318 Alarm Unit
IC-306
(Max. 3 units)
Standard supply for SSAS
Navigator

*: At least two SSAS Alert Units are required.

**: Mandatory for EGC operation as required by IMO RES. A.664(16).

CATEGORY OF UNITS (required by IEC60945):

Unit Category
Terminal Unit Protected from the weather (For indoor installation)
Antenna Unit Exposed to the weather (For installation on the open deck)
Other Units Protected from the weather (For indoor installation)

ii
EQUIPMENT LISTS
Standard supply
Name Type Code No. Qty Remarks
Antenna Unit IC-118 - 1 w/FP16-02501
Terminal Unit IC-218 - 1 w/CP16-05200, SP16-01301, FP16-02600
Junction Box IC-318 - 1
SSAS Alert Unit IC-307 - 2 For SSAS only
Installation CP16-05511 001-189-560 1 For IC-118, 30 m
Materials

Optional supply
Name Type Code No. Qty Remarks
Printer PP-520 - 1
Distress Alert/ Re-
IC-305 - 1
ceived Call Unit
Alarm Unit IC-306 - 1
AC/DC Power Supply
PR-240 - 1
Unit
SSAS Alert Unit IC-307 - 1
PC Terminal Software OP16-57 001-180-050 1
Cable Assy. COSPEVVSBC 5PX0.2LF 000-560-452-11 1 5P, 10 m
COSPEVVSBC 5PX0.2LF 000-103-868-11 1 5P, 20 m
COSPEVVSBC 5PX0.2LF 000-103-869-11 1 5P, 30m
COSPEVVSBC 5PX0.2LF 000-132-829-11 1 5P, 40 m
COSPEVVSBC 5PX0.2LF 000-132-828-11 1 5P, 50 m
Flush Mount Kit OP16-27 004-448-000 1 For IC-305/306
OP16-28 004-448-010 1 For IC-307
Antenna Unit IC-118 - 1
Antenna Bracket CP16-05602 001-189-610 1 For IC-118
Antenna Base w/Hose OP16-72 001-323-420
1
Clamp
Antenna Base w/ OP16-73 001-323-430
1
Mount Pipe
Antenna Base 2/U Bolt OP16-74 001-313-440 1
Antenna Base OP16-75 001-313-450 1
IPX2 Kit OP16-58 001-180-070 1 D-sub cables
Water Proof Kit OP16-59 001-180-080 1 For IC-218
OP16-60 001-180-090 1 For IC-318
OP16-67 001-189-380 1 For IC-305
OP16-68 001-189-400 1 For IC-307
GPS Board Kit OP16-62 001-180-100 1 For IC-218
Bracket Kit OP16-65 001-182-900 1
Key Template OP05-135 001-184-560 1 For Russian flag
vessels

iii
EQUIPMENT LISTS

Name Type Code No. Qty Remarks

Installation Materials CP16-05750 000-021-704 1 w/o pipe, 30 m
CP16-05790 000-021-715 w/o pipe, 30 m,
for armored cable
w/o pipe, 40/50 m,
CP16-05760 000-021-713
for armored cable
CP16-05770 000-021-714 w/o pipe, 100 m,
for armored cable
Hose clamp OP16-76-1 001-443-450 1 Nominal Diameter,
Mast Diameter
For 40A (I 48.6)
OP16-76-2 001-443-460 1 Nominal Diameter,
Mast Diameter
For 65A to 80A
(I 76.3 to 89.1)
OP16-76-3 001-443-470 1 Nominal Diameter,
Mast Diameter
For 90A to 100A
(I 101.6 to 114.3)

iv
1. MOUNTING

NOTICE
Do not apply paint, anti-corrosive sealant or contact
spray to coating or plastic parts of the equipment.
Those items contain organic solvents that can damage
coating and plastic parts, especially plastic connectors.

1.1 Antenna Unit

1.1.1 Mounting location

Refer to IMO resolutions A663(16) and A.807(19), as amended.

• Mount the omnidirectional antenna

ANTENNA UNIT
unit high atop a mast clear of stays
and the turning diameter of a radar
antenna. The ideal mounting loca- 5 5 15 15
tion would be where no obstacle
appears in the fore and aft direc-
tions down to -5° and down to 15°
in the port and starboard directions. The concept is illustrated in the figure below.
Shadow sector of the antenna mast, whip antenna, etc. should be within two de-
grees at one meter from the antenna unit.

• When two FELCOMs are installed, the horizontal

separation shall be at least 1.5 m and the vertical
separation, 1 m or more. -15°
1 m or more

• If Inmarsat ship earth stations other than C are in-

stalled, separate the Inmarsat antenna at least 8 m 1.5 m or more
from the Inmarsat-C antenna. Installation of two antenna units

• Separate the antenna unit Install above this line

from an S-band radar as
INSTALLTION
shown in the figure to the right:
ZONE
PROHIBITED
2m
15° 1.5 m ZONE

2m
5m
S-band radar HORIZONTAL LINE

1-1
1. MOUNTING

• The allowable vibration level as specified by Inmarsat is as shown in the table be-
low.
Allowable vibration level
Frequency Level
2 to 10 Hz 2.54 mm Peak Amplitude
10 to 100 Hz 9.8 m/s2 Peak Acceleration
• Avoid the location near tunnels and stacks; smoke and soot on the radome can low-
er signal level (10 m or more in horizontal distance).
• Separate the antenna unit 5 m from HF, VHF of 27 MHz antenna.

1.1.2 Mounting
The antenna cable is available in lengths of 30 m, 50 m and 100 m (see table below).

Cable length Type Remarks

30 m (no armor) TP5FBAW-5DFB TNC connector at both ends
30 m (w/armor) 5D-FB-CV-NP N connector on one end (antenna side)
50 m (w/armor) 8D-FB-CV
100 m (w/armor) 12D-SFA-LITE-CV
Note: When using the optional installation kit to install the antenna, refer to the outline
drawings at the back of this manual.

Antenna installation
Select a location to weld the grounding stud bolt (M6), keeping in mind the length of
the grounding cable RW-4747 (Included as installation materials) is 340 mm. The lo-
cation for welding the grounding stud bolt should allow the antenna ground and mast
ground to be connected with the grounding cable (to ground lightning strikes). For de-
tailed measurements, refer to the outline drawings at the back of this manual.

For information on wiring the antenna cable, refer to the manual included with the an-
tenna unit.

Ground wire

Ground terminal M6 grounding stud bolt

(Shipyard supply)
Antenna base Hose clamp

Cable Mast (Shipyard supply)

1-2
 1. MOUNTING

1.2 Terminal Unit

Select a mounting location, considering the following points.

• The temperature and humidity should be moderate and stable.

• For maintenance and checking purposes, leave sufficient space at the sides and
rear of the unit and leave slack in cables.

Mounting
Tabletop mount
1) Fix the hanger (option) to a table with four self-tapping screws (5x20, supplied), re-
ferring to the outline drawing at the back of this manual.
2) Screw knobs and washers to terminal unit loosely.
3) Set the terminal unit to the hanger and tighten knobs.

Terminal unit, tabletop mounting

Flush mount
Use locally supplied pan head screws (M4x20) when the thickness of the bulkhead is
from 11 to 14 mm. For bulkhead which exceeds 14 mm in thickness the length of the
pan head screws should be bulkhead thickness A +7.8±2 mm. Also the length of B
should be max. 8 mm (Bd8 mm).

B A

Bulkhead, sectional view

1. Prepare a cutout in the mounting location whose dimensions are as shown in the
outline drawing at the back of this manual.
2. Fix the display unit with six pan head screws, inserting them from the inside of the
bulkhead. Refer to the outline drawing at the end of this manual.

1-3
1. MOUNTING

How to connect the LAN cable

Connect the LAN cable using the sponge and LAN cable support (supplied). This pro-
cedure should be done even if the LAN cable is not used, to waterproof the unit.

1. Attach the sponge for LAN terminal to the LAN terminal.

Sponge for
LAN terminal

2. Use the binding screw (pre-attached at the rear of the unit) to fix the LAN cable
support.

LAN cable
support

3. Connect the LAN cable to the terminal unit. Fix the LAN cable to the LAN cable
support with a cable tie (supplied).

Binding screw

Fix the cable here

with a cable tie.

1-4
 1. MOUNTING

Keyboard
1. Attach the function key label (IMN-C18) to the keyboard as shown below.
2. Attach four fasteners (small, supplied) to the bottom of the keyboard.
3. Attach four fasteners (large, supplied) to the small fasteners attached at step 2.
4. Remove the paper from four fasteners.
5. Fasten the keyboard to the mounting place.

Function key label (supplied)

or

1.3 Distress Alert/Received Call Unit IC-305/Alarm

Unit IC-306

ALARM ALARM
ACK ACK

Distress alert/received call unit IC-305 Alarm unit IC-306

Bulkhead mounting
1. Remove four screws from the unit to separate the bottom chassis from the top
cover.
2. Fix the bottom chassis to the mounting location with four self-tapping screws (sup-
plied).
3. Cable can be led in from the bottom or the rear panel. For rear panel entrance,
change the clamp orientation as follows.
1) Unfasten two screws to remove the cable clamp.
2) Turn the clamp 90 degrees.

1-5
1. MOUNTING

3) Refasten two screws removed at step 1) to fix the clamp.

Unfasten these screws.
Refasten screws.

Rotate.

4) Run the interconnection cable thorough a cable entrance and connect it to ter-
minal board.

Flush mount
The optional flush mounting kit OP16-27 (Code No.: 004-448-000) is required.

Name Type Code No. Qty

Fixture 16-018-4201-1 100-317-841 1
Pan head screw M3x6 000-800-362 4
Self-tapping screw 4x16 000-162-605-10 4
1. Make a cutout in the mounting location, referring to the outline drawings at the
back of this manual.
2. Fix the unit to the fixture with four pan head screws (supplied).
3. Fasten four self-tapping screws (I5, supplied) to fasten the fixture to the mounting
position.

1.4 Printer (option)

Mount the printer (PP-510 or PP-520) 405
on a tabletop with the fixtures sup-
plied. Refer to the outline drawing at
the end of this manual for the mount-
ing dimensions. The right figure is for
PP-520

1. Decide the location of the printer.

2. Set the ink ribbon cartridge and
the roll paper to the printer. 200

3. Set the fixtures (left/right) onto

the printer. Fasten them with four
self-tapping screws (I5x20).

1-6
 1. MOUNTING

1.5 AC/DC Power Supply Unit PR-240 (option)

Fix the unit on a table with four self-tapping screws.

AC/DC power supply unit PR-240

1-7
1. MOUNTING

1.6 Junction Box IC-318

The junction box IC-318 is connected to the terminal unit by using the cable assy
16S0344 (2 m, attached to the junction box). Install the junction box within 2 m from
the terminal unit.

1. Remove four screws from the unit to separate the bottom chassis from the top
chassis.
2. Fix the bottom chassis to the mounting location with four self-tapping screws
(4x16, supplied).
3. Connect the cables referring to Chapter 2.

Junction box IC-318

1-8
2. WIRING

24 VDC

VCTF-0.75x3C (5 m)

For cable w/armor

Cable Assy. 0.34 m

TPA5FB0.4NJ5FBA-5DFB Printer
Ground wire PP-510/PP-520
5D-FB-CV-NP, 30 m TP5FBAW-5DFB,30
8D-FB-CV, 50 m m (No armor)
12D-SFA-CV, 100 m Connector at both 16S0184, 3 m
ends
Connector at one end

TNCP-NJ
connector DGPS
(Supplied)
LAN cable
Connector N-P-5DFB (100Base-TX, local supply)
N-P-8DFB Mini keyboard
N-P-12DSFA (to USB terminal
(Supplied, local arrangement) on the front panel)

Copper strap
MJ-A3SPF0018-050Z 1.2 m

CAUTION Power supply

The terminal unit is shipped with a 15 A 24 VDC
fuse in its power cable. This fuse is for use
with a 12 VDC power supply.

For a 24 VDC power supply, replace the

fuse with a 7A fuse (supplied). Attach the Junction Box
"7A" label to the fuse holder on the power IC-318
cable. Use of a wrong fuse can damage
the equipment.

CO-SPEVV-SB-C 0.2x5p
(option) or TTYCS(LA)-4
(Japanese Industrial
Standards)

IC-307 Navigator

Distress alert/ Alarm unit

Received call IC-306
unit IC-305
or IC-350

Wiring of FELCOM 18

2-1
2. WIRING

2.1 Antenna Cable Connector at the Terminal Unit

5D-FB-CV-NP (30 m)

Outer Sheath Inner Sheath

Armor Braided Shield
Remove the outer sheath, armor and inner-
sheath by the dimensions shown.
50 15
Set the nut, washer, gasket, clamp onto
Cover with heat-shrink tubing and heat.
cable as shown.
Washer

- Be careful not to damage the braided

30 shield.
Clamp
Gasket
Nut Fold back the braided shield onto the clamp
3.5 and trim the shield as shown.
Insulator
Core Make the length of insulator 3.5 mm and the
5 length of the core 5 mm.
- Be careful not to damage the core.
Cut braided shield here.

Set the center pin to the core and solder the

Center Pin
pin from the hole in the pin.
(Pull the pin with approx. 1 kg of force to
check strength of solder joint.)
- Be sure the solder is flush with surface of
Solder here. pin.
- Be sure there is no gap between center
pin and insulator. Do not push the center pin
into the insulator.
- Do the soldering as quickly as possible so
as not to deform the insulator.

Insulator Ring

Set the ring and insulator ring onto the

cable.
Ring

Shell
Set the shell to the cable then turn the nut to
tighten. (Do not tighten by turning shell.) -
Use a wrench or the like to tighten the nut
securely.
Nut

How to fabricate antenna cable 5D-FB-CV-NP

2-2
 2. WIRING

8D-FB-CV (50 m)

Dimensions in millimeters.
Outer Sheath Remove outer sheath and armor by the
Armor Inner Sheath Shield dimensions shown left.
Expose inner sheath and shield by the
dimensions shown left.
50 30

Cover with heat-shrink tubing and heat.

Remove insulator and core by 10 mm.

30 10

Twist shield end.

Slip on clamp nut, gasket and clamp as shown

left.
Clamp Nut Clamp
Gasket (reddish brown)
Aluminum Foil

Fold back shield over clamp and trim.

Trim shield here.

Cut aluminum foil at four places, 90 from one

Insulator another.

Fold back aluminum tape foil onto shield and trim.

Trim aluminum tape foil here.

1
Expose the insulator by 1 mm.
5
Expose the insulator by 5 mm.

Pin
Clamp Nut Slip the pin onto the conductor. Solder them
Shell
together through the hole on the pin.

Insert the pin into the shell. Screw the

Solder through the hole.
clamp nut into the shell.
(Tighten by turning the clamp nut. Do not
tighten by turning the shell.)

How to fabricate antenna cable 8D-FB-CV

2-3
2. WIRING

12D-SFA-LITE-CV (100 m)

Outer Sheath Dimensions in millimeters.

Armor Inner Sheath Shield Remove outer sheath and armor by the
dimensions shown left.
Expose inner sheath and shield by the
80 12 dimensions shown left.

Cover with heat-shrink tubing and heat.

30
Twist shield end.

Slip on clamp nut, gasket and clamp as shown left.

Nut Gasket Clamp

Washer

1.8
Expose the insulator by 1.8 mm.

Expose the core by 4.5 mm.

4.5
Pin
Clamp Nut Slip the pin onto the conductor. Solder them
together through the hole on the pin.
Insert the pin into the shell. Screw the clamp
nut into the shell.
(Tighten by turning the clamp nut. Do not
Solder through the hole.
tighten by turning the shell.)

How to fabricate antenna cable 12D-SFA-CV

2-4
 2. WIRING

2.2 Distress Alert/Received Call Unit IC-305

Use the installation materials CP16-02201 to connect the IC-305. The optional CO-
SPEVV-SB-C 0.2x5P cable or JIS cable (Japan Industrial Standard) TTYCS(LA)-4 or
equivalent are available to connect with the junction box IC-305. Select the cable
clamp attached according to the diameter of cable, and fix the armor of the cable with
the clamp.

16P0213

For CO-SPEVV- 1 2 3 4 5
SB-C 0.2x5P

Twist the shield.

For TTYCS-4 (JIS) (or drain wire)
or equivalent CO-SPEVV-SB-C 0.2X5P
or TTYCS(LA)-4
Distress alert IC-305
15 mm 40 mm 10 mm
Cut unused cables.
Wiring of distress alert IC-305

2.3 Alarm Unit IC-306

A maximum of three alarm units can be connected to the junction box IC-318, in par-
allel. To distinguish the incoming indictors, set jumper wires for the second alarm unit
as shown below. For connection, refer to 2.2 Distress Alert/Received Call Unit IC-
305.”

16P0213 JP2
JP1

Alarm unit IC-306

No.1 (default setting) No.2 No.3
JP1 Open Open Short
JP2 Short Open Open

2-5
2. WIRING

2.4 Junction Box IC-318

Use the junction box IC-318 to connect the distress alert/received call unit IC-305 and
other units (max. four units) to the terminal unit. Unfasten four screws to remove the
units cover to connect cables.

For connection, use the optional 5 pair cable CO-SPEVV-SB-C 0.2x5P, JIS cable (Ja-
pan Industrial Standard) TTYCS(LA)-4 or equivalent.

1 Vcc

IC-305/306
2 GND
Cover 3 TD/RD-A
4 TD/RD-B
5 NC
6 ALM-H 1
7 ALM-C 2
8 RD-A(NAV)
Cable clamp 9 RD-B(NAV)
10 GND
11 SSAS OUT-H
12 SSAS OUT-C
13 SSAS IN-H
Terminal board 14 SSAS IN-C 3 Core 7 mm
15 SSAS CTR

Sticker for
connection of
other equipment Procedure
1. Insert from direction 1 .
2. Tilt slightly toward 2 .
For TTYCSLA cable, use the screws
and crimp-on lugs shown below to 3. Insert cable core to 3 .
connect the drain wire of that cable.
4. Pull out the screwdriver.
Screws and crimp-on lugs
Note 1: Do not insert the wire deeply, to
(supplied in the IC-318)
prevent pinching its sheath.

Note 2: Pull the wire slightly to confirm

that it is in the slot correctly.
Fold back
IC-318, inside view

15 mm 90 mm 7 mm

Junction Box IC-318

Input sentences
The following sentences can be input by a GPS navigator.

Input sentences
BWC, BWR, DBT, DTM, GGA, GLL, GNS, GSA, MTW, RMA, RMB, RMC,
VDO, VDR, VTG, WPL, ZDA

2-6
3. INITIAL SETTINGS
This chapter shows you how to setup the equipment. Some procedures require entry
of job no. and password. Ask your dealer.

3.1 How to Set the IMN (INMARSAT MOBILE NO.)

Set your IMN (Inmarsat Mobile No.) as shown below.

1. Turn the power on.

2. Press the function key [F8] to show the [Setup] menu.

File Edit Transmit EGC Reports Logs Options Setup Distress StopAlarm

Setup
1. System Setup
2. Editor Setup
3. Terminal Setup
4. EGC Setup
5. Auto Mode Setup
6. E-Mail Setup
7. Directories
8. Configuration

3. Press 1 key to display the [System Setup] menu.

Setup
System Setup
System Date & Time 01:53 12-02-25 (YY-MM-DD)
IMN
MES Operation Mode INMARSAT-C
Nav Port EXT
LAN Port ON
Message Output Port INT
EGC Output Port INT
Network Setup
Command Window

4. Confirm that [IMN] is selected, and then press the Enter key.
An input box appears.
5. Key in your IMN.
6. Press the Enter key.
To clear the IMN, select [IMN], then press I, M, N while pressing the Alt key. Re-
peat step 4 to step 6 to input the correct IMN.
7. Press the Esc key.
8. Press the Enter key.
9. Press the Esc key.

3-1
3. INITIAL SETTINGS

3.2 How to Set External Equipment

The FELCOM 18 is set at the factory to accept the distress alert/received call unit IC-
305, up to three alarm units IC-306 and the SSAS alert unit IC-307. If the configuration
is different, change the setting to OFF as below.

1. Press the F8 key to show the [Setup] menu.

2. Press the 1 key to show the [System Setup] menu.
3. Press the p key to select [Command Window], and then press Enter key to show
the [Command Window] screen.
4. Enter the [Enter JOB No.:], and then press the Enter key.
5. Enter the [PASSWORD:], and then press the Enter key.
[Main Menu] is highlighted.
6. Press the 1 and Enter keys in order.
Setup
System Setup
System Date & Time 01:53 02-02-25 (YY-MM-DD)
IMN
Command Window
MES Operation Mode INMARSAT-C
[ Main Menu ]
1. Remote Box Setup
2. External Alarm Setup
3. AMS Setup
4. Management Profile Setup
Enter JOB No.: 1
[ Remote Box Setup ]
1. SSAS OFF
2. IC-305 OFF
3. IC-306 No.1 OFF
4. IC-306 No.2 OFF
5. IC-306 No.3 OFF
E: Exit
Enter No.:

Command Window screen

7. Press the number key for unit not connected.
For example, press the 1 and Enter keys when the SSAS alert unit IC-307 is not
connected.
[ SSAS ]
1. OFF
2. IC-307 (Standard SSAS)
3. IC-307 (Russian SSAS)
4. SSAS(Momentary SW)
E: Exit

Setting window for IC-307

8. If the unit is not connected, press the 1 key, and the Enter key.
To return to the [Remote Box Setup] menu, press the E key (not any numeric key).
9. Repeat step 7 to step 8 for other units not connected.
10. Press the Esc key several times to close the menu.

3-2
 3. INITIAL SETTINGS

3.3 How to Set the Alarm Contact

1. Press the F8 and 1 keys to show the [System Setup] menu.
2. Press p to select [Command Window], and then press the Enter key.
3. Enter the [Enter JOB No.:], then press the Enter key.
4. Enter the [PASSWORD:], and then press the Enter key.
[Main Menu] is highlighted.
5. Press the 2 key, and the Enter key.
Command Window

[ External Alarm Setup ]

1. Distress Message : ON
2. Distress EGC : ON
3. Urgent EGC : ON
4. Unit Fault : OFF
E: Exit
Enter No.:

6. Press a numeric key (1 to 4), then press the Enter key.

To detect the error on a unit, press 4 and Enter in order.

[ Unit Fault ]
1. ON
2. OFF E: Exit

7. Press the 1, and Enter keys.

To return to the [External Alarm Setup] menu, press the E key.
8. Repeat steps 6 and 7 to set other alarm contacts.
9. Press the Esc key several times to close the menu.

3.4 How to Set up the AMS/BAM

Do the following to connect the AMS (Alert Management System).

1. Press the F8 and 1 keys to show the [System Setup] menu.

2. Press p to select [Command Window], and then press the Enter key.
3. Enter the [Enter JOB No.:], then press the Enter key.
4. Enter the [PASSWORD:], then press the Enter key.
5. Press the 3 key, and the Enter key.
Command Window

[ AMS Setup Menu ]

1. Mode Setup
2. MY SFI Setup
3. Transmission Group Setup
4. Error Log
E: Exit
Enter JOB No.:

6. Press appropriate numeric key (1 to 4), then press the Enter key.
To return to the [AMS Setup Menu], press the E key at the setting window.

3-3
3. INITIAL SETTINGS

1 key: [Mode Setup] Command Window

Set the alert mode. [ Mode Setup ]

1. Legacy ON
[Legacy]: Select when no AMS/BAM is 2. AlertIF1
connected. 3. AlertIF2
E: Exit
[AlertIF1]: Select when AMS is connected. Enter AMS Mode No.:
[AlertIF2]: Select when BAM is connected.

For [AlertIF1], the option window shown Command Window

to the right is displayed. To return to the [ Mode Setup ] Command Window
[AMS Setup Menu] from this window, 1. Legacy ON
[ AlertIF1 Option ]
press the E key twice. 2. AlertIF1
E: Exit Distress Alarm Stop Enable
1.
2. Distress Alarm Stop Disable ON
Enter AMS Mode No.:
[Distress Alarm Stop Enable]: The AMS E: Exit
Enter AlertIF1 Option No.:
can stop the alarm sound when the Dis-
tress Priority message is received.
[Distress Alarm Stop Disable]: The AMS can not stop the alarm sound when a
Distress Priority message is received.

For [AlertIF2], the option window shown Command Window

to the right is displayed. To return to the
[ Mode Setup ] Command Window
[AMS Setup Menu] from this window, 1. Legacy ON
[ AlertIF2 Setup ]
press the E key twice. 2. AlertIF1
1. BAM SFI1 XX9999
3. AlertIF2
2. BAM SFI2 XX9999
E: Exit
Select the appropriate BAM unit to setup. EnterE: ExitMode No.:
AMS
Enter AlertIF2 Option No.:

The [AlertIF2 Setup] option window Command Window

shown to the right is displayed.
[ Mode Setup ] Command Window
1. Legacy ON
Set the SFI for the connected BAM [ AlertIF2 Option ]
2. AlertIF1 Command Window
1. BAM SFI1 XX9999
3. AlertIF2
unit. 2. BAM [ BAM
SFI2 SFI Setup ]
XX9999
E: Exit
SFI1 XX9999
EnterE: ExitMode No.:
AMS
Enter AlertIF2 Option No.:
E: Exit C: Clear
Enter SFI:

2 key: [MY SFI Setup] Command Window

Set the SFI of FELCOM18. Enter the four- [ MY SFI Setup ]

SFI CS0001
digit number that follows “CS”.
0000 to 9998: SFI No.
E: Exit
Enter SFI No.:

3-4
 3. INITIAL SETTINGS

3 key: [Transmission Group Setup]

Set the AMS Transmission Group.
Command Window
Transmission Group Multicast Address Destination Port
[ Transmission Group Setup ] MISC 239.192.0.1 60001
1. MISC ON TGTD 239.192.0.2 60002
2. TGTD SATD 239.192.0.3 60003
3. SATD
4. NAVD NAVD 239.192.0.4 60004
5. VDRD VDRD 239.192.0.5 60005
6. RCOM
RCOM 239.192.0.6 60006
7. TIME
8. PROP TIME 239.192.0.7 60007
9. USR PROP 239.192.0.8 60008
E: Exit
USR1 to USR8 239.192.0.9 to 60009 to
Enter Group No:
239.192.0.16 60016

4 key: [Error Log] Command Window

The [Error Log] compiles AMS re- [ Error Log ]

Datagram header error xxxxxxxxxx*
lated errors. To delete an error log TAG block formatting error xxxxxxxxxx
entry, select the log then press TAG checksum error xxxxxxxxxx
TAG syntax error xxxxxxxxxx
the 1, Enter key. TAG framing error xxxxxxxxxx
Sentence syntax error xxxxxxxxxx
UDP checksum error xxxxxxxxxx
The error log holds 4294967296 Total 4294967295 LIMIT MAX
entries. When that count is
1. Log Clear
reached, the message "LIMIT E: Exit
MAX" appears. Enter JOB No.:
*: xxxxxxxxxx: Error log count

7. Press the Esc key several times to close the menu.

3-5
3. INITIAL SETTINGS

3.5 How to Select Position-fixing Equipment

Select the position-fixing equipment that is to feed navigation data to the FELCOM.

1. Press the F8 and 1 keys to show the [System Setup] menu.

2. Select [NAV Port] then press the Enter key.
3. Select the navigator to use, then press the Enter key.
OFF: Manually input the position of own ship. Alarm is outputted when the position
data is not updated every four hours.
Auto: INT or EXT is automatically selected. For SSAS Russia and LRIT Russia,
the setting of [NAV Port] is fixed at Auto and GLONASS is prioritized.
INT: Use the navigator that is built into the terminal unit.
EXT: Use an external navigator.
4. Press the Esc key several times to close the menu. The [Update] window ap-
pears.
5. Select [Yes] then press the Enter key.

3.6 How to Set up for 2nd DTE

For a 2nd DTE, do the procedure shown below.
1. Press the F8 and 3 keys to show the [Terminal Setup] menu.
Terminal Setup
Connection
Date Disp. Form YY-MM-DD
Screen Saver OFF
Window Color

Terminal Setup menu (for 2nd DTE)

2. [Connection] shows the name of the terminals available for connection to the LAN
interface. Press the Enter key to show the [Connect List].

Connect List
No. Name IMN IP Address Software Version
*01 F18_123456 123432588 172.31.16.100/24 1650247-01
02 F18_133234 456789210 192.168.16.11/24 1650247-01
03
04
05
06
07
08
09
10

The No., Name, IMN, IP address and software version of each terminal are
shown. The asterisk marks the terminal currently selected for communication.
3. To connect to a different terminal, select it then press the Enter key. The [Con-
nect] window appears and [Yes] is selected. Press the Enter key to connect the
terminal.

3-6
 3. INITIAL SETTINGS

3.7 How to Set the Russian Language

Do the following to create a message in Russian.

1. Press the F8 and 1 keys to show the [System Setup] menu.

2. Press p to select [Command Window], and then press the Enter key.
3. Type "RUSSIAN ON" in the [Enter JOB No.:], then press the Enter key.
The language is switched to Russian and the message "Russian supported." ap-
pears at the bottom of the standby display.
To restore the previously used language, type "RUSSIAN OFF" in the [Enter JOB
No.:], then press the Enter key. "Russian supported." disappears from the screen.

4. Press and hold down the left Shift key while pressing the left Alt key.
The language for the keyboard is switched from English to Russian. The Scroll
Lock lamp lights when Russian is selected. To switch the language from Russian
to English, press and hold down the left Shift key while pressing the left Alt key.
Note: With a 2nd DTE, Russian can be input from the keyboard of your PC. See
your PC’s owner’s manual for how to switch languages.
5. Put the key template for Russian (OP05-135) on the keyboard of your PC.

3.8 How to Use the Paper Save Function

The Paper Save function allows you to choose whether to print the “Successful Data
Report Sending” confirmation after a data report is sent.

1. Press the F8 and 1 keys to show the [System Setup] menu.

2. Press p to select [Command Window], and then press the Enter key.
3. At the [Enter JOB No.:] prompt, type "Paper Save", then press the Enter key. A
message is displayed showing the status of the Paper Save function (ON or OFF).
4. To change the setting, type "Paper Save ON" (No report is printed) or "Paper Save
OFF" (Report is printed), as appropriate, then press the Enter key.

3-7
3. INITIAL SETTINGS

This page is intentionally left blank.

3-8
4. HOW TO INSTALL OPTIONAL
EQUIPMENT

4.1 GPS Board OP16-62

This chapter provides the procedure for the installation of the GPS board (in the ter-
minal unit), which provides GPS position information.

Name: GPS board

Type: OP16-62
Code No.: 001-180-100

Name Type Code No. Qty

Binding Screw M3x6 000-163-479-10 3
GPS Board 16P0246 004-656-550 1
Connector Assy. 51065-0700-PHR7-L110 000-176-305-10 1
Note: Use anti-static gloves to handle board.
1. Unfasten 18 screws, six spacers and three nuts to remove the terminal unit cover.

Torque Nut
0.76±0.02 N m Rounding
side
Nut,
Torque flat washer
1.37±0.1 N m Cover
Spacer
6 pcs.
Pan head screw
M3x8, 18 pcs.

* *
*
* ** ** *
*
* *
* *
* * *
*
* * * *
*
* * *

*: Remove.
2. Fasten three binding screws (M3x6, supplied with the kit) to attach the GPS Board
to the RF cover.

4-1
4. HOW TO INSTALL OPTIONAL EQUIPMENT

3. Attach the 51065-0700-PHR7-L110 connector assy. between J13 on the TER-

MCPU Board and J1 on the GPS board.

Binding screw
M3x6, 3 pcs.

J6
GPS board

J13

4. Attach the cable from the GPS board to J6 on the RF COMMCPU Board.
Use the clamp next to the connector to fix the cable.
5. Reassemble the terminal unit.

4.2 IPX2 Kit OP16-58/OP16-59

The optional kits OP16-58 and OP16-59 are used to protect the connectors on the ter-
minal unit from water splash. Note that these optional kits should be used as a pair.

4.2.1 OP16-58 (cables)

Connect the waterproofed D-sub cables to the rear of the terminal unit, instead of the
standard supply cable. For the connection at the IC-318, see section 4.3.

OP16-58 (Code No.: 001-180-070)

Name Type Code No. Qty

Cable Assy. H230817-1 001-176-552-10 1
H230817-2 000-176-553-10 1
XM-FD-361 000-176-551-10 1

4-2
 4. HOW TO INSTALL OPTIONAL EQUIPMENT

4.2.2 OP16-59 (for connector ports)

OP16-59 (001-180-080)

Name Type Code No. Qty

Sponge for Dsub 16-023-3531 100-369-600-10 1
Cover for BNC 16-023-3534 100-369-630-10 1
Cover for USB 16-023-3535 100-369-641-10 1
USB Support 16-023-3536 100-369-650-10 1
Sponge for BNCR 16-023-3541 100-369-690-10 1
Dummy Plate 9P 16-023-3542 100-368-190-10 1
Dummy Plate 15P 16-023-3543 100-369-700-10 1
Dummy Plate 25P 16-023-3544 100-369-710-10 1
Binding Screw #4-40UNCX3/16 000-176-619-10 6

USB port

1
Attach the cover for USB
(16-023-3535) to the USB
connector, then connect it to
the terminal unit.

Cover for USB (triangle

mark should be upward.)

2
Fasten two binding screws
(pre-attached) to fix the USB
support (16-023-3536) as
shown right.

USB support

4-3
4. HOW TO INSTALL OPTIONAL EQUIPMENT

D-sub ports

1
Peel the paper from the
sponge for Dsub (16-023-
3531), then attach the sponge
to the D-sub connectors at the
rear of the terminal unit.

Sponge for Dsub

2 (Cables connected)

Connect the cables supplied

with OP16-58 to the appro-
priate ports.

(No cables connected)

Use the binding screws

(#4-40UNCx3/16) to fix the
dummy plates (for 9P, 15P
and 25P) to the appropriate
ports.

4-4
 4. HOW TO INSTALL OPTIONAL EQUIPMENT

DGPS port
(Coaxial cable connected)

1
Pass the coaxial cable
through the slit on the cover
for BNC (16-023-3534).

Cover for BNC

2
Attach the connector* of the
coaxial cable to the DGPS
port.

*For waterproofing, use the

connector assy. shown below: USB suppor
-BNCP-58U-BNCP L-200
(000-161-953-11)
-BNCP-58U-BNCP L-290
(000-175-274-11)

3
Slide the cover for BNC on
the connector to cover the Triangle mark
connector. Confirm that the
triangle mark on the cover is
upward.

4-5
4. HOW TO INSTALL OPTIONAL EQUIPMENT

(Coaxial cable not connected)

1 Sponge for BNCR

Remove the cap from the
DGPS port, then atttach the
sponge for BNCR (16-023-
3541) around the port.

Cap

2
Re-attach the cap to the
DGPS port.

4-6
 4. HOW TO INSTALL OPTIONAL EQUIPMENT

4.3 Waterproofing Kit OP16-60/OP16-67/OP16-68

You can use the optional waterproof kits to keep water splash out of the unit. Note that
each kit is specifically designed for each unit.

OP16-60 (for IC-318)

The IC-318 should be installed on a desktop. To ensure the waterproof rating is main-
tained, use the optional waterproofing kit OP16-60. If a floor installation is required,
make sure the area is not subject to water splash, rain or other water ingress.

OP16-60 (Code No.: 001-180-090)

Name Type Code No. Qty

Cover gasket 16-023-5502 100-373-530-10 1
Grommet 16-023-5503 100-373-541-10 1

When the OP16-58 (described in paragraph 4.2.1) is used, replace the cable from the
IC-318 with the XM-FD-361 as shown below.

Attach the grommet

to this notch. # Color
1 Blue
2 Brown
3 Purple
4 Gray
Pan head screw 5 -
(M4x8, 2 pcs.) 6 Green
Attach the cover
gasket to here 7 Yellow
(reverse side). 8 Orange
9 Pink
10 Light-green
Cable assy. 11 White (w/black dots)
XM-FD-361 12 White (w/red dots)
13 Black
14 Red
15 Light-blue

4-7
4. HOW TO INSTALL OPTIONAL EQUIPMENT

OP16-67 (for IC-305), OP16-68 (for IC-307)

Note: To maintain the waterproofing, these units must be installed on a bulkhead or
wall, with the cable entry facing downwards. Further, the optional kits do not provide
waterproofing if the unit is installed with the cable entry facing upwards.

OP16-67 (Code No.: 001-189-380)

Name Type Code No. Qty

Fixing Tape 24-009-1225 100-366-200-10 2

OP16-68 (Code No.: 001-189-400)

Name Type Code No. Qty

Waterproofing Cover 16-023-5501 100-374-950-10 1
Fixing Tape 24-009-1225 100-366-200-10 2

1. Unfasten four screws to remove cover of IC-305/IC-307.

2. Attach supplied fixing tape to the underside of the cover as shown in the illustra-
tion below.
Fixing tape

(IC-305) (IC-307)

3. Attach the cover.

4. For IC-307, remove the seal from the waterproofing cover and attach the cover as
shown in the illustration below.

4-8
5. HOW TO CHANGE POWER SUP-
PLY SPECIFICATIONS
The AC-DC power supply PR-240 is shipped ready for connection to a 200-230 VAC
ship’s mains. If the ship’ mains is 100 VAC, change the tap connection and terminal
board connection as below. Attach a label supplied as accessories to the front panel
according to the ship’s mains.

Ship’s mains Tap connection Terminal board Label

200 to 230 VAC SEL 230 V Below (a) 200-230 VAC, 2.2-1.7 A,
1I 50/60 Hz
100 to 115 VAC SEL 115 V Below (b) 100-115 VAC, 3.2-2.6 A,
1I 50/60 Hz

Remove screw
and cover.

Cover

Front panel
(a) 200-230 VAC
Relay
1 Black Coil
2 Gray 3
J4 2
3 1

SEL
Terminal board 1
115V
2
3 Heat sink
4 SEL
(b) 100-115 VAC 5 230V
6
1 Black 7
8
2 Gray
3
Tap connection
(Pull out to disconnect.)

Front panel
Attach appropriate label.

AC FAIL: Connect to Alarm system.

Output Setting: Normal Close Set plug to 2 & 3 pins of J4 (Factory setting)
Normal Open Set plug to 1 & 2 pins of J4
AC Power Switch
(When connecting DC input, note that the DC power is
supplied even though this switch is turned off.)

Note: The DC output load must be less than 8 A.

5-1
5. HOW TO CHANGE POWER SUPPLY SPECIFICATIONS

This page is intentionally left blank.

5-2
APPENDIX 1 JIS CABLE GUIDE

Cables listed in the manual are usually shown as Japanese Industrial Standard (JIS). Use the following guide to locate
an equivalent cable locally.

JIS cable names may have up to 6 alphabetical characters, followed by a dash and a numerical value (example:
DPYC-2.5).
For core types D and T, the numerical designation indicates the cross-sectional Area (mm2) of the core wire(s) in the
cable.
For core types M and TT, the numerical designation indicates the number of core wires in the cable.

1. Core Type 2. Insulation Type 3. Sheath Type

D: Double core power line P: Ethylene Propylene Y: PVC (Vinyl)
T: Triple core power line Rubber
DPYCY
M: Multi core
TT: Twisted pair communications
(1Q=quad cable)

4. Armor Type 5. Sheath Type 6. Shielding Type TPYCY

C: Steel Y: Anticorrosive vinyl S: All cores in one sheath
sheath -S: Indivisually sheathed cores
SLA: All cores in one shield, plastic
tape w/aluminum tape
-SLA: Individually shielded cores, MPYC-4
plastic tape w/aluminum tape

1 2 3 4 5 6 1 2 3 4

EX: TTYCYSLA - 4 MPYC - 4 TTYCSLA-4

2
Designation type Core Area (mm ) Designation type # of cores

The following reference table lists gives the measurements of JIS cables commonly used with Furuno products:
Core Cable Core Cable
Type Area Diameter Diameter Type Area Diameter Diameter

DPYC-1.5 1.5mm2 1.56mm 11.7mm TTYCS-1 0.75mm2 1.11mm 10.1mm

2 2
DPYC-2.5 2.5mm 2.01mm 12.8mm TTYCS-1T 0.75mm 1.11mm 10.6mm
DPYC-4 4.0mm2 2.55mm 13.9mm TTYCS-1Q 0.75mm2 1.11mm 11.3mm
DPYC-6 6.0mm2 3.12mm 15.2mm TTYCS-4 0.75mm2 1.11mm 16.3mm
2 2
DPYC-10 10.0mm 4.05mm 17.1mm TTYCSLA-1 0.75mm 1.11mm 9.4mm
DPYCY-1.5 1.5mm2 1.56mm 13.7mm TTYCSLA-1T 0.75mm2 1.11mm 10.1mm
2 2
DPYCY-2.5 2.5mm 2.01mm 14.8mm TTYCSLA-1Q 0.75mm 1.11mm 10.8mm
DPYCY-4 4.0mm2 2.55mm 15.9mm TTYCSLA-4 0.75mm2 1.11mm 15.7mm
2 2
MPYC-2 1.0mm 1.29mm 10.0mm TTYCY-1 0.75mm 1.11mm 11.0mm
MPYC-4 1.0mm2 1.29mm 11.2mm TTYCY-1T 0.75mm2 1.11mm 11.7mm
2 2
MPYC-7 1.0mm 1.29mm 13.2mm TTYCY-1Q 0.75mm 1.11mm 12.6mm
MPYC-12 1.0mm2 1.29mm 16.8mm TTYCY-4 0.75mm2 1.11mm 17.7mm
2 2
TPYC-1.5 1.5mm 1.56mm 12.5mm TTYCY-4S 0.75mm 1.11mm 21.1mm
TPYC-2.5 2.5mm2 2.01mm 13.5mm TTYCY-4SLA 0.75mm2 1.11mm 19.5mm
2 2
TPYC-4 4.0mm 2.55mm 14.7mm TTYCYS-1 0.75mm 1.11mm 12.1mm
TPYCY-1.5 1.5mm2 1.56mm 14.5mm TTYCYS-4 0.75mm2 1.11mm 18.5mm
2 2
TPYCY-2.5 2.5mm 2.01mm 15.5mm TTYCYSLA-1 0.75mm 1.11mm 11.2mm
TPYCY-4 4.0mm2 2.55mm 16.9mm TTYCYSLA-4 0.75mm2 1.11mm 17.9mm

AP-1
 ,&$ ,&$* ,&$ +. $9;  
㹎㸿㹁㹉㹇㹌㹅ࠉ㹊㹇㹑㹒
1$0( 287/,1( '(6&5,37,21&2'(θ 4
7< 1$0( 287/,1( '(6&5,37,21&2'(θ 4
7<
ࣘࢽࢵࢺ 81,7 㺡㺛㺢㺱㺎㺢㺼᧯సᡭ㡰
& 
㺞㺮㺣㺷㺳㺤㺠㺢
 66$67(6702'(+$1'%22.
,&$

7(50,1$/81,7
 㺩㺋㺎㺛㺼ኚ᭦ࡢ࠾㢪࠸
& 㺺㺒㺐 
ணഛရ 63$5(3$576
127,),&$7,21'2&80(17
ணഛရ 
63  ᶵჾᘬΏࡋ๓ࡢὀព
63$5(3$576 & 㺺㺒㺐 
 %()25('(/,9(5,1*72
௜ᒓရ $&&(6625,(6 )3 2:1(5 
㺮㺤㺕㺎㺬㺼㺎㺢㺼 ྲྀᢅㄝ᫂᭩
 20  
8%/$&.
.(<%2$5' 23(5$725
60$18$/
 
ᕤ஦ᮦᩱ ,167$//$7,210$7(5,$/6 ྲྀᢅㄝ᫂᭩
&3 
20 
㺗㺎㺪㺼㺷⤌ရ0- 23(5$725
60$18$/
0-$63)=&  
&$%/($66< ᧯సせ㡿᭩ⱥ
 26( 
ᕤ஦ᮦᩱ 23(5$725
6*8,'((1
 㻔㻖㻝㻕
&3 
,167$//$7,210$7(5,$/6 ⿦ഛせ㡿᭩
 ,0  
ᕤ஦ᮦᩱ ,167$//$7,210$18$/
&3  
,167$//$7,210$7(5,$/6 㐼㞴㏻ಙせ㡿
 7,& 㺺㺒㺐 
ᅗ᭩ '2&80(17 ',675(66&20081,&$7,21
㺏㺪㺽㺶㺗㺎㺚㺌㺻㺪㺉㺯 
- 㺺㺒㺐 
5(*,675$7,21)25
6(59,&($&7,9$7,21 
䡶㻙䢀䢚␒ྕᮎᑿ䛾㼇㻖㻖㼉䛿䚸㑅ᢥရ䛾௦⾲䡶䡬䢀䢚䜢⾲䛧䜎䛩䚹
㻯㻻㻰㻱㻌㻺㼁㻹㻮㻱㻾㻌㻱㻺㻰㻵㻺㻳㻌㼃㻵㼀㻴㻌㻎㻖㻖㻎㻌㻵㻺㻰㻵㻯㻭㼀㻱㻿㻌㼀㻴㻱㻌㻯㻻㻰㻱㻌㻺㼁㻹㻮㻱㻾㻌㻻㻲㻌㻾㻱㻼㻾㻱㻿㻱㻺㼀㻭㼀㻵㼂㻱㻌㻹㻭㼀㻱㻾㻵㻭㻸㻚

㻔㻖㻝㻕䛾᭩㢮䛿䚸ⱥᩥ௙ᵝᑓ⏝䛷䛩䚹
A-1

㻔㻖㻝㻕㻌㻹㻭㻾㻷㻱㻰㻌㻰㻻㻯㼁㻹㻱㻺㼀㻿㻌㻭㻾㻱㻌㻲㻻㻾㻌㻱㻺㻳㻸㻵㻿㻴㻌㻿㻱㼀㻌㻻㻺㻸㼅㻚

凚␎ᅗ僔ᑍἲ僕傎ཧ⪃್働傿傏䢢䣆䣋䣏䣇䣐䣕䣋䣑䣐䣕䢢䣋䣐䢢䣆䣔䣃䣙䣋䣐䣉䢢䣈䣑䣔䢢䣔䣇䣈䣇䣔䣇䣐䣅䣇䢢䣑䣐䣎䣛䢰凛

&=(
 #8:   #8:  
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀 㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
('.%1/#('.%1/#*-('.%1/#) A-2 ('.%1/#55#5('.%1/#)55#5 A-3

0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6; 0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;

࡙࠾࠶࠻ 70+6 ࡙࠾࠶࠻ 70+6
㨻㩧㩍㩏㩟㩐㨹㩎▫⹣ຠ 㨻㩧㩍㩏㩟㩐㨹㩎▫⹣ຠ
+%  +% 
#06'00#70+6%1/2.'6'5'6 #06'00#70+6%1/2.'6'5'6
   
㩊㨺㩚㩏㩣㩟㩐㨹㩎▫⹣ຠ 㩊㨺㩚㩏㩣㩟㩐㨹㩎▫⹣ຠ
+%#  +%# 
6'4/+0#.70+6%1/2.'6'5'6 6'4/+0#.70+6%1/2.'6'5'6
   
ធ⛯▫▫⹣ຠ ធ⛯▫▫⹣ຠ
+%  +% 
,70%6+10$1:%1/2.'6'5'6 ,70%6+10$1:%1/2.'6'5'6
 
Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5 ଻቟⼊ႎ⊒๭ེ
㩃㨺㩖㩨㩣⚵ຠ +% 
 55#5#.'4670+6
62($#9&($/
%#$.'#55; 
 ઃዻຠ #%%'5514+'5
Ꮏ੐᧚ᢱ ઃዻຠ
%2  (2 
+056#..#6+10/#6'4+#.5 #%%'5514+'5
 
Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
㩃㨺㩖㩨㩣⚵ຠ
62($#9&($/ 
%#$.'#55;

Ꮏ੐᧚ᢱ
%2 
+056#..#6+10/#6'4+#.5

Ꮏ੐᧚ᢱ
%2 
+056#..#6+10/#6'4+#.5

࿑ᦠ &1%7/'06
+%:ᒁ߈ᷰߒ೨ߩᵈᗧ
% 
$'(14'&'.+8'4+0)61190'4

㩀㩔㩨㨺⾍ઃⷐ㗔ᦠ
% 
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯 #66#%*/'061(59+6%*%18'4
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅 
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅

ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅 ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩 㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
%<'
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩 %<'
 #8:   #8:  
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀 㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
+%*- A-4 +% A-5

0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6; 0#/' 176.+0' &'5%4+26+10%1&'ͳ 3 6;

࡙࠾࠶࠻ 70+6 ࡙࠾࠶࠻ 70+6
㨻㩧㩍㩏㩟㩐㩌㩎 ធ⛯▫

+%  +% 
#06'00#70+6 ,70%6+10$1:
  
ઃዻຠ #%%'5514+'5 Ꮏ੐᧚ᢱ +056#..#6+10/#6'4+#.5
ઃዻຠ Ꮏ੐᧚ᢱ

(2  %2 
#%%'5514+'5 +056#..#6+10/#6'4+#.5
 
࿑ᦠ &1%7/'06
㨻㩧㩍㩏੤឵ᣇᴺ
6+% 
#06'00#+056#..4'2#.%'


䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅

ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯 ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯

㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷 㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅 㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅

䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩 䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
%<$ %<#
 16AK-X-9856 -3 1/1 16AK-X-9855 -3 1/1
ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ
A-6 A-7
IC-306 IC-305
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY N A M E O U T L I N E DESCRIPTION/CODE № Q'TY
ユニット UNIT ユニット UNIT
着信指示器 遭難警報器
IC-306 1 IC-305 1
ALARM UNIT DISTRESS ALERT UNIT
000-043-429-00 000-043-427-00 **
工事材料 INSTALLATION MATERIALS CP16-02201 工事材料 INSTALLATION MATERIALS CP16-02201
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1ｼｭ +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1ｼｭ
3X10 SUS304 4 3X10 SUS304 4
SELF-TAPPING SCREW SELF-TAPPING SCREW
000-162-604-10 000-162-604-10
圧着端子 圧着端子
FV1.25-3(LF) 4 FV1.25-3(LF) 4
CRIMP-ON LUG CRIMP-ON LUG
000-166-756-10 000-166-756-10
圧着端子 圧着端子
FV2-3 1 FV2-3 1
CRIMP-ON LUG CRIMP-ON LUG
000-157-246-10 000-157-246-10
図書 DOCUMENT
IC-305/307引き渡し前の注意
C52-00202-* 1
BEFORE DELIVERING TO OWNER
(*1)
000-809-354-1*

1.(*1） の＊＊＊＊は、有り・ 無しの仕様が有ります。

A V A ILA B LE W ITH O R W ITH O U T ***** U N IT.

型式/ｺｰ ﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。 型式/ｺｰ ﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。

TW O TYP ES A N D C O D ES M A Y B E LIS TED FO R A N ITEM . TH E LO W ER P R O D U C T M A Y B E S H IP P ED IN P LA C E O F TH E U P P ER TW O TYP ES A N D C O D ES M A Y B E LIS TED FO R A N ITEM . TH E LO W ER P R O D U C T M A Y B E S H IP P ED IN P LA C E O F TH E U P P ER
P R O D U C T.Q U A LITY IS TH E S A M E. P R O D U C T.Q U A LITY IS TH E S A M E.
（略図の寸法は、参考値です。 D IM EN S IO N S IN D R A W IN G FO R R EFER EN C E O N LY.） （略図の寸法は、参考値です。 D IM EN S IO N S IN D R A W IN G FO R R EFER EN C E O N LY.）
C5635-Z05-C C5635-Z04-C
 16AK-X-9853 -6 1/1
ＰＡＣＫＩＮＧ ＬＩＳＴ A-9
A-8
IC-307
&2'(12  $9; 
N A M E O U T L I N E DESCRIPTION/CODE № Q'TY 7<3( 
&3
ユニット UNIT
保安警報発呼器 ᕤ஦ᮦᩱ⾲
IC-307 1
SSAS ALERT UNIT ,167$//$7,210$7(5,$/6
000-043-474-00 ␒ྕ ྡࠉࠉ⛠ ␎ࠉࠉᅗ ᆺྡ㸭つ᱁ ᩘ㔞 ⏝㏵㸭ഛ⪃
付属品 ACCESSORIES 287/,1( 4
7<
12 1$0( '(6&5,37,216 5(0$5.6
DｶﾊﾞｰL組品
㺩㺋㺎㺛㺼㺨㺶㺭㺎㺖
9 05-073-1111-0 ROHS 1 52+6
 
DISTRESS COVER )86(/$%(/
40 &2'(
22 100-274-720-10 12 
工事材料 INSTALLATION MATERIALS
㺏㺎㺛ᯈ
+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1ｼｭ
 52+6 
&233(5675$3
3X10 SUS304 4
&2'(
SELF-TAPPING SCREW 12 
000-162-604-10 /$1㺗㺎㺪㺼㺷㺙㺙㺒
圧着端子 
 
/$1&$%/(6833257,1*
FV1.25-3(LF) 8
&2'(
CRIMP-ON LUG 12 
000-166-756-10 /$1㺴㺑㺛㺬㺽㺻㺚㺼
圧着端子  
6321*()25/$1 
FV2-3 2 &2'(
CRIMP-ON LUG 12 
000-157-246-10 㺢㺵㺛㺞㺍㺩㺽㺻㺦㺚㺼ࠉ㺚㺋
図書 DOCUMENT  ;686
6(/)7$33,1*6&5(: 
IC-305/307引き渡し前の注意
&2'(
1 12 
C52-00202-*
BEFORE DELIVERING TO OWNER 㺘㺻㺫㺼㺍㺖㺛
000-809-354-1*  &9% 
&$%/(ࠉ7,(
ｶﾊﾞｰ貼付要領書 &2'(
1 12 
C52-00403-*
ATTACHMENT OF SWITCH COVER 㺩㺋㺎㺛㺼
000-150-849-1*  )*%2$9$3%) 
*/$6678%()86(
&2'(
12 

型式/ｺｰ ﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
TW O TYP ES A N D C O D ES M A Y B E LIS TED FO R A N ITEM . TH E LO W ER P R O D U C T M A Y B E S H IP P ED IN P LA C E O F TH E U P P ER
P R O D U C T.Q U A LITY IS TH E S A M E. 㸦␎ᅗࡢᑍἲࡣࠊཧ⪃್࡛ࡍࠋࠉ',0(16,216,1'5$:,1*)255()(5(1&(21/<㸧

（略図の寸法は、参考値です。 D IM EN S IO N S IN D R A W IN G FO R R EFER EN C E O N LY.） 㹄㹓㹐㹓㹌㹍ࠉ㹃㹊㹃㹁㹒㹐㹇㹁ࠉ㹁㹍ࠉ㸬㸪㹊㹒㹂

C5635-Z02-D &0%
 A-10 A-11

&2'(12  $9;  %1&'01  #8: 

7<3( &3  6;2' %2 

ᕤ஦ᮦᩱ⾲ Ꮏ੐᧚ᢱ⴫
,167$//$7,210$7(5,$/6 +056#..#6+10/#6'4+#.5
␒ྕ ྡࠉࠉ⛠ ␎ࠉࠉᅗ ᆺྡ㸭つ᱁ ᩘ㔞 ⏝㏵㸭ഛ⪃ ⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂ ↪ㅜ㧛஻⠨
12 1$0( 287/,1( '(6&5,37,216 4
7< 5(0$5.6 01 0#/' 176.+0' &'5%4+26+105 3 6; 4'/#4-5
㺘㺻㺫㺼㺍㺖㺛 㺏㺻㺡㺣㺗㺎㺪㺼㺷ᅛᐃ⏝ 㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨㩆㨷
)RUVHFXULQJWKH
 &9%  DQWHQQDFDEOH  :575 
&$%/(7,( 5'.(6#22+0)5%4'9
&2'( %1&'01
12  
㺪㺼㺟㺷㺘㺼㺯㺡㺎㺪㺽
 12 
6(/)%21',1*7$3(
&2'(
12 
㺗㺎㺪㺼㺷⤌ရ
 5: 
&$%/($66<
&2'(
12 

ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬

6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
㸦␎ᅗࡢᑍἲࡣࠊཧ⪃್࡛ࡍࠋࠉ',0(16,216,1'5$:,1*)255()(5(1&(21/<㸧 㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕

㹄㹓㹐㹓㹌㹍ࠉ㹃㹊㹃㹁㹒㹐㹇㹁ࠉ㹁㹍ࠉ㸬㸪㹊㹒㹂 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰

&0' %/#
 A-12 A-13

&2'(12  $.; 

%1&'01  #8: 
7<3( 63 %2;123
6;2' %2 
6+,312 63$5(3$576/,67)25 86( 6(763(5
9(66(/
Ꮏ੐᧚ᢱ⴫
+056#..#6+10/#6'4+#.5
⇟ภ ฬ‫ޓޓ‬⒓ ⇛‫ޓޓ‬࿑ ဳฬ㧛ⷙᩰ ᢙ㊂ ↪ㅜ㧛஻⠨
01 0#/' 176.+0' 3 6; 48$17,7< 5(0$5.6&2'(12
&'5%4+26+105 4'/#4-5 ':*12
,7(0 1$0(2) :25.,1*
㩖㨱㩇㩏㨺
 12 287/,1( 25
3$57
7<3(12 3(5 3(5 63$5(
 41*5  6(7 9(6
*11-.112(#56'0'4
%1&' 㺩㺋㺎㺛㺼
01 
 */$6678%(   
㩖㨱㩇㩏㨺
 )86( )*%2$9
$3%)
 41*5  
*11-.112(#56'0'4
%1&' 㺩㺋㺎㺛㺼
01 
 */$6678%(   
㩔㩢㩙㨺㩂 )86( )*%2$9
$3%)
   
.#$'.
%1&'
01 

ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ 0)5
61$0( )85812(/(&75,&&2/7' ':*12 &3( 
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4 㸦␎ᅗࡢᑍἲࡣࠊཧ⪃್࡛ࡍࠋࠉ',0(16,216,1'5$:,1*ࠉ)255()(5(1&(21/<㸧
241&7%637#.+6;+56*'5#/'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕

㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
%/#
D-1
24/Jan/2012 Y.NISHIYAMA
D-2
24/Jan/2012 Y.NISHIYAMA
'
 '

17/May/2012 Y.NISHIYAMA
 '

July 14'03
17/May/2012 Y.NISHIYAMA
'
 '

Dec. 20, '02

17/May/2012 Y.NISHIYAMA
'
 '

6/Oct/2010 Y. NISHIYAMA
16/Jun/2014 H .M A KI
'
26/Oct/09 R.Esumi
'
6/Jul/2012 Y.NISHIYAMA
'
 '

17/May/2012 Y.NISHIYAMA
 '

30/Apr/2012 Y.NISHIYAMA
D-15
 S-1
     

࢔࣮࣒ࣛࣘࢽࢵࢺ
 9&& $/$50 81,7
3
 *1' ,&
 7'5'$ 
3
 7'5'%
࢔ࣥࢸࢼࣘࢽࢵࢺ *1'
$17(11$ 81,7 
,&
ࢱ࣮࣑ࢼࣝࣘࢽࢵࢺ ,&ࢆ᥋⥆ࡍࡿ࡜ࡁ㸦,&࡜ࡢඹ⏝୙ྍ㸧
7(50,1$/ 81,7 ᥋⥆⟽ 㐼㞴㆙ሗჾ
$

71&31-
73$)%1- '6)$/,7(&9Pȭ 13'6)$ ,& -81&7,21 %2; ',675(66 $/(57  &211(&7,21 )25 ,& '2 127 86( : ,&
)%$')%P ')%&9Pȭ 13')% -81&7,21 -( 5(&(,9(' &$// 81,7
,& 77<&6/$  25
')%&9Pȭ 13')% '& P &2[3  0$;P ,& ,&
9FF$/0    9&& 㑅ᢥ 77<&6/$  25 ,10$56$7 1R
$17 3 &2[3 
*1'    *1' 6(/(&7   75$
73)%$:')%%Pȭ 7'5'$    7'5'$   75% ࢔࣮࣒ࣛࣘࢽࢵࢺ
7'5'%  
3
 7'5'%  )* $/$50 81,7
1&   77<&6/$  25  *1' ,&
'*36 &2[3  ࢔࣮࣒ࣛࢩࢫࢸ࣒
%1& $/0+  
'*36ࢹࢥ࣮ࢲ࣮ &2$; &$%/(Ȑ $/0&   77<&6/$  25 $/$50 6<67(0
'*36 '(&2'(5 5'$  
&2[3  ⯟ἲ⿦⨨ ಖᏳ㆙ሗⓎ࿧ჾ
86% 5'%   1$9 (48,30(17 66$6 $/(57 81,7
$ 7<3( ,&    ,&1R ,&1R
*1'  
࣮࣮࢟࣎ࢻ P 
77<&6/$  25 &2[3 
.(<%2$5' 66$6B287+    66$6B287+       
66$6B287&    1&  
3 3 3
66$6B&+(&.    66$6B&+(&.  
66$6B,1&    66$6B,1&  
-( 3 3 3
35,17(5 66$6B&75/    66$6B&75/  
5+%3*6 ࣉࣜࣥࢱ  '&
 *1'  
9&7)[&Pȭ 
35,17(5 
6 
 9'&  㺏㺔 5(' 33 
 㺖㺹 %/. 6 Pȭ 
% *1' 㺚㺹 :+7 ࡲࡓࡣ 25 ,9VT ᭱኱㸱ྎࡲ࡛᥋⥆ྍ⬟
+  /$1 5- 0$;  81,76 $9$,/$%/(
  77<&6/$  25
㜵Ỉ௙ᵝࢣ࣮ࣈࣝ 
673&$7 ࣃࢯࢥࣥ+8% &2[3 
:$7(53522) &$%/(
 9'& '&'&ࢥࣥࣂ࣮ࢱ 3& 25 +8% ྜィ ᭱኱P
'&'& &219(57(5 727$/ 83 72 P
$9 '& ,1
$9 0-$63)
0-$63)=
9'& ࢩࣟ :+7  '&
Pȭ
ࢡࣟ %/.  '&
 *1'
 
 9$& '3<&
ȭ+] $& $&'& 9'&  㜵Ỉ௙ᵝࢣ࣮ࣈࣝ
 ,1 㖡ᯈ ᥋⥆⟽
㟁※㺳㺤㺍㺢 287  &233(5 675$3 ,& :$7(53522) &$%/(
 9'& '3<&  '& $&'& 32:(5 -81&7,21 %2;
: P 
 ,1 6833/< 81,7 -81&7,21 ;0)'P ,&
( 35   ࢔࢜ %/8 
3(   ࢳࣕ %51 
,9VT  㺯㺵㺙㺕 33/ 
ಖㆤ࢔࣮ࢫ  ࣁ࢖ *5< 
 
&  㺮㺢㺼㺶 *51 
 ࢟ <(/ 
 㺞㺼㺐 25* 
 ࣔࣔ 31. 
 㺑㺛㺮㺢㺼㺶 /*51 
 㺚㺹㺖㺹 :+7%/. 
 㺚㺹㺏㺔 :+75(' 
 ࢡࣟ %/. 
 ࢔࢝ 5(' 
 ࣑ࢬ /%/8 

'
ὀグ
㸨㸯㸧㐀⯪ᡤᡭ㓄ࠋ
㸨㸰㸧࢜ࣉࢩࣙࣥࠋ
㸨㸱㸧⤊➃ࡢ,&ࡣࢪࣕࣥࣃ࣮タᐃࢆኚ᭦ࡍࡿࠋ '5$:1 7,7/(
㸨㸲㸧66$6௙ᵝࡢ࡜ࡁᶆ‽ᵓᡂࠋ -DQ 7<$0$6$., )(/&20 
&+(&.(' ྡ⛠
127( -DQ +0$., ࢖࣐ࣥࣝࢧࢵࢺ& ⯪⯧ᆅ⌫ᒁ
 6+,3<$5' 6833/< $33529('
27/Jan/2016 H.MAKI ┦஫⤖⥺ᅗ
 237,21
6&$/( 0$66 1$0(
 &+$1*( 6(77,1* 2) -803(5 ,1 ,& 72 7(50,1$7( &2[3 &263(996%& [3ȭ NJ ,10$56$7& 0(6
 67$1'$5' &21),*85$7,21 )25 66$6 &2[3 &263(996%& [3ȭ ':* 1R 5()1R
&& *  ,17(5&211(&7,21 ',$*5$0