KL

Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders

- New design of the profile for easier cleaning
- Grooves for recessed sensors and connections on one side for easy installation
- Traditional UNIVER technology to ensure strength and reliability
- Dimensions complying with international standards for a full interchangeability

Available ATEX version upon request

II 2Gc IIC T5 II 2Dc T100°C

TECHNICAL CHARACTERISTICS
Working temperature -20 ÷ 80 °C
Fluid filtered air, with or without lubrication 1
Working pressure 1,5 ÷ 10 bar

CYLINDERS
Bores Ø 032 - 040 - 050 - 063 - 080 - 100 - 125 mm
Cushionings adjustable in both sides

CONSTRUCTIVE CHARACTERISTICS
End-caps die-cast aluminium (painted)
Barrel anodized aluminium
Piston die-cast aluminium
Guide slide acetalic resin
Piston rod chromium-plated steel standard,
stainless steel, rolled AISI 303
Piston seal double-lip seal in nitrile rubber (NBR)
Guide bush for piston rod UNIVER Original self-lubricating and self-aligning
Shock absorber seals nitrile rubber (NBR) in both sides
Magnet plasto-ferrite (standard supplied)

CODIFICATION KEY

K L 2 0 0 0 3 2 0 0 5 0 M
1 2 3 4 5 6 7 8

1 Series 2 Type 3 Version 4 Bore (mm)

KL = Ø 32÷125 mm - ISO 15552 1 = Stainless steel piston rod 00 = D.A. Standard version 032 = Ø32 080 = Ø80
Pneumatic cylinders 2 = Chromium-plated steel 01 = D.A. Through piston rod 040 = Ø40 100 = Ø100
piston rod 60 = S.A. Retracted piston rod Max stroke 50 mm 050 = Ø50 125 = Ø125
70 = S.A. Extended piston rod Max stroke 50 mm 063 = Ø63

D.A. = Double acting

S.A. = Single acting
5 Stroke (mm) 6 Option 7 Magnetic 8 Atex option
0025 = 25 0150 = 150 0320 = 320 0700 = 700 F = Preset for locking unit M = Magnetic version X = Atex (upon request)
0050 = 50 0160 = 160 0350 = 350 0800 = 800 reduced protrusion standard supplied
0075 = 75 0175 = 175 0400 = 400 0900 = 900 See ATEX Catalogue
G = Preset for locking unit
0080 = 80 0200 = 200 0450 = 450 1000 = 1000 for types and versions
ISO protrusion
0100 = 100 0250 = 250 0500 = 500
0125 = 125 0300 = 300 0600 = 600

Versions with high temperature seals (Max 120°C) and version with low temperature seals (Max -40°C) available upon request

Subject to change STANDARDS-BASED CYLINDERS 1.1

9
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Stroke Single acting cylinder

tolerances Theoretical forces (N) for return stroke
Ø stroke ≤ 500 501 ≤ stroke ≤ 1000 Ø Max force Min. force
mm mm stroke 50 mm stroke 50 mm
32 +2 - 0 +3,2 - 0 32 52 28
40 +2 - 0 +3,2 - 0 40 70 42,5
50 +2 - 0 +3,2 - 0 50 98 48
63 +2,5 - 0 +4 - 0 63 98 48
80 +2,5 - 0 +4 - 0 80 140 80
100 +2,5 - 0 +4 - 0 100 140 80
125 +4 - 0 +5 - 0 125 235 175

Theoretical forces (N) Cushion

at different working pressure (bar)
Ø Surface area Working pressure Working pressure Ø Length Max kinetic energy absorption
mm2 bar bar mm Nm
Thrust Traction Thrust Traction 32 18 1,8
2 4 6 8 10 2 4 6 8 10 40 24 2,5
32 804 691 161 322 482 643 804 138 276 414 553 691 50 24 4,5
40 1256 1056 251 502 754 1005 1256 211 422 633 844 1055 63 30 8
50 1962 1649 393 785 1178 1570 1963 330 660 990 1320 1650 80 30 12
63 3116 2802 623 1246 1869 2493 3116 560 1120 1680 2240 2800 100 35 21
80 5024 4533 1005 2010 3014 4019 5024 907 1814 2722 3629 4536 125 35 36
100 7850 7359 1570 3140 4710 6280 7850 1472 2944 4416 5888 7360
125 12266 11462 2453 4906 7359 9812 12266 2294 4588 6882 9176 11470

Mass - Standard cylinder

Ø Cylinder - stroke 0 Increase per mm stroke Moving element - stroke 0 Increase per mm stroke
g g g g
1 32
40
480
710
2,05
3,06
130
250
0,9
1,6
50 1180 4,28 440 2,5
63 1740 4,91 550 2,5
80 2740 7,20 970 3,9
100 3920 8,00 1190 3,9
125 6830 12,40 2200 6,3

Mass- Through piston rod cylinder

Ø Cylinder - stroke 0 Increase per mm stroke Moving element - stroke 0 Increase per mm stroke
g g g g
32 550 2,92 190 1,8
40 850 4,62 360 3,2
50 1440 6,72 640 4,9
63 2010 7,36 740 4,9
80 3190 11,0 1350 7,6
100 4460 11,8 1570 7,6
125 7810 18,53 3050 12,4

Graph of theoretical forces/pressure

and acceptable strokes depending on maximum peak load
Theoretical force (N)
3000 5000 30000 50000
20 30 40 50 100 200 300 400 500 1000 2000 4000 10000 20000 40000
10
8
Pressure (bar)

32 40 50 63 80 100 125
6
5
4
3

2
2000

1000
800

600
32 (125)
500
400
25 (80/100)
300
Stroke (mm)

20 (50/63)
200

16 (40)
12 (32)

100
20 30 40 50 100 200 300 400 500 1000 2000 4000 10000 20000 40000
3000 5000 30000 50000
Max peak load for bending (N)

1.1 STANDARDS-BASED CYLINDERS Subject to change

10
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Fixing elements and accessories

16
16

14
15
13

12

21
11
10
16
6
15 16 8

16 17
14
16 20
19 7

13 18 1

CYLINDERS
1
2

4
5
18 19 20
22

DESCRIPTION NOTE PART NO.

1 Female fork with clips KF-15 _ _ _
2 Articulated self-lubricating fork KF-17 _ _ _
3 Fork with axially mounted articulated pin KF-22 _ _ _
4 Fork with angle-mounted articulated pin KF-23 _ _ _
5 Floating joint KF-24 _ _ _
6 Female hinge (ISO MP2) with pin KF-10 _ _ _ A
7 Narrow female hinge with pin (DIN648K) KF-10 _ _ _ AS
8 Counter-hinge 90° (CETOP RP107P) KF-19 _ _ _ CTA
9 Counter-hinge 90° KF-19 _ _ _
10 Articulated counter-hinge (DIN648K) KF-19 _ _ _ SC
11 Articulated rear male hinge (ISO MP6) KF-11 _ _ _ S
12 Rear male hinge (ISO MP4) KF-11 _ _ _
13 Front - rear flange (ISO MF1-MF2) KF-12 _ _ _
14 Angle bracket (ISO MS1) KF-13 _ _ _
15 Front - rear hinge with floating pin KF-14 _ _ _ AP
16 Support for hinges KF-41 _ _ _
17 ISO intermediate hinge (ISO MT4) KLF-14 _ _ _
18 DF magnetic sensor (see accessories section) DF- _ _ _
19 Cable clamping for DF sensor (see accessories section) DF-001
20 DHF covering strip (see accessories section) DHF-0020100
21 Locking unit L1-N
22 Slide unit J12
Subject to change STANDARDS-BASED CYLINDERS 1.1
11
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Double acting/Single acting

A Pneumatic cushioning adjusting screw

KL100/200
D.A. Standard
KL160/260
S.A. Retracted piston rod
KL170/270
S.A. Extended piston rod
For extended rod version add WH+Z (stroke) dimensions

Double acting through piston rod

KL101/201
D.A. Through piston rod
Z= Stroke
Ø A ØB BG E+0,5 KK I2 I3 I8 PL RT SW TG VA VD WH ØMM EE M 1 2 ZM
32 22 30 16 46,5 M10x1,25 16 5 94 ±0,4 14 M6 10 32,5 ±0,5 3,5 5 26 12 G1/8 4,4 17 6 146
40 24 35 16 52 M12x1,25 20 5 105 ±0,7 16 M6 13 38 ±0,5 4 5,5 30 16 G1/4 5 19 6 165
+3,0
50 32 40 17 64,5 M16x1,5 26 6 106 ±0,7 15,5 M8 17 46,5 ±0,6 4 6 37 20 G1/4 6 24 8 180 -1,5
63 32 45 18 76,5 M16x1,5 26 6 121 ±0,8 17,5 M8 17 56,5 ±0,7 4 6 37 20 G3/8 8 24 8 195
80 40 45 20 95 M20x1,5 32 7 128 ±0,8 20 M10 22 72 ±0,7 4 8 46 25 G3/8 7,5 30 10 220
100 40 55 20 114 M20x1,5 35 7 138 ±1 20,5 M10 22 89 ±0,7 4 8 51 25 G1/2 9 30 10 240 +3,5
125 54 60 24 140 M27x2 45 8 160 ±1 20,5 M12 27 110 ±1,1 5,5 10 65 32 G1/2 11 41 12 290 -2,0

1.1 STANDARDS-BASED CYLINDERS Subject to change

12
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Tandem version
CODIFICATION KEY
K L 2 A 0 3 2 0 5 0 M
1 2 3 4 5
1 Series 2 Type 3 Bore (mm) 4 Stroke (mm) 5 Magnetic
KL = Ø 32÷125 mm - ISO 15552 1A = Double thrust tandem only for forward 032 = Ø32 080 = Ø80 Upon request M = Magnetic version
Pneumatic cylinders movement, stainless steel piston rod 040 = Ø40 100 = Ø100 (standard supplied)
Magnetic version 2A = Double thrust tandem only for forward 050 = Ø50 125 = Ø125
standard supplied movement, chromium-plated steel piston rod 063 = Ø63
1D = Double thrust tandem only for reverse
movement, stainless steel piston rod
2D = Double thrust tandem only for reverse
movement, chromium-plated steel piston rod

Z = Stroke
Ø EE L S Max
32 G1/8 169 3
40 G1/4 189 5
50 G3/8 175 4
63 G3/8 195 7
80 G1/2 211 6
100 G1/2 224 9
125 G1/2 251 9

CYLINDERS
Tandem cylinders are constructed using two pistons coupled together which provide double the force in forward movement compared to the traditional ISO cylinders of the same bore
size.

Two-position tandem version

CODIFICATION KEY
K L 2 B 0 3 2 0 5 0 0 7 0 M
1 2 3 4 5 6
1 Series 2 Type 3 Bore (mm) 4 Stroke Z1 (mm) 5 Stroke Z2 (mm) 6 Magnetic
KL = Ø 32÷125 mm - ISO 15552 1B = Two-position tandem, 032 = Ø32 080 = Ø80 Stroke of rear Stroke of head M = Magnetic version
Pneumatic cylinders stainless steel 040 = Ø40 100 = Ø100 cylinder cylinder (standard supplied)
Magnetic version 050 = Ø50 125 = Ø125 (upon request) (upon request)
standard supplied 2B = Two-position tandem, 063 = Ø63
chromium-plated steel

Z = Stroke
L + Z1 + Z2
Ø EE L S Max
32 G1/8 166 3
40 G1/4 186 5
50 G1/4 172 4
63 G3/8 192 7
80 G3/8 208 6
100 G1/2 221 9
125 G1/2 248 9

Two-position cylinders with two independent piston-rods which allow to realize a double positioning in which
the thrust forces are the same as those of an ISO cylinder of the same bore size.

For all other dimensions please refer to the standard version.

For other types of cylinders kindly contact our sales office.

Subject to change STANDARDS-BASED CYLINDERS 1.1

13
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Opposed tandem version

CODIFICATION KEY
K L 2 C 0 3 2 0 3 0 0 5 0 M
1 2 3 4 5 6

1 Series 2 Type 3 Bore (mm) 4 Stroke Z1 (mm) 5 Stroke Z2 (mm) 6 Magnetic

KL = Ø 32÷125 mm - ISO 15552 1C = Opposed tandem, 032 = Ø32 080 = Ø80 Shorter stroke Longer stroke M = Magnetic version
Pneumatic cylinders stainless steel 040 = Ø40 100 = Ø100 (upon request) (upon request) (standard supplied)
Magnetic version 050 = Ø50 125 = Ø125
standard supplied 2C = Opposed tandem, 063 = Ø63
chromium-plated steel

Z = Stroke
Ø L VL
32 194 6
40 220 10
50 222 10
63 252 10
80 266 10
100 288 12
125 334 14

1
Type of cylinder characterized by the coupling of two cylinders and whose piston rods move in opposite directions. The values of the thrust force are the same as those of the traditional
cylinders.

With common piston rod tandem version (upon request)

Z = Stroke
Ø I8 VM
32 94 ±0,4 48
40 105 ±0,7 54
50 106 ±0,7 69
63 121 ±0,8 69
80 128 ±0,8 86
100 138 ±1 91
125 160 ±1 119

Two coupled cylinders with common piston rod

The values of the thrust force are the same as those of the traditional
cylinders .
For all other dimensions please refer to the standard version.
For other types of cylinders kindly contact our sales office

1.1 STANDARDS-BASED CYLINDERS Subject to change

14
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Female hinge (ISO MP2) with pin

Material: Aluminium, zinc-plated steel pin Z = Stroke

Ø CB CD E FL L MR UB XD Mass Part no.
H14 H9 ± 0,2 min. Max h14 g
32 26 10 48 22 12 11 45 142 ±1,25 75 KF-10032A
40 28 12 54 25 15 13 52 160 ±1,25 110 KF-10040A
50 32 12 65 27 15 13 60 170 ±1,25 150 KF-10050A
63 40 16 75 32 20 17 70 190 ±1,6 270 KF-10063A
80 50 16 95 36 20 17 90 210 ±1,6 420 KF-10080A
100 60 20 115 41 25 21 110 230 ±1,6 765 KF-10100A
125 70 25 140 50 30 26 130 275 ±2 1445 KF-10125A

Narrow female hinge with pin (DIN648K)

CYLINDERS
Material: Aluminium, zinc-plated pin Z = Stroke
Ø CB CD E FL L MR UB XD Mass Part no.
H14 H9 ± 0,2 min. Max h14 g
32 14 10 45 22 10 10 34 142 ±1,25 68 KF-10032AS
40 16 12 52 25 16 12 40 160 ±1,25 112 KF-10040AS
50 21 16 65 27 16 14 45 170 ±1,5 196 KF-10050AS
63 21 16 75 32 21 18 51 190 ±1,6 288 KF-10063AS
80 25 20 95 36 22 20 65 210 ±1,6 566 KF-10080AS
100 25 20 115 41 27 22 75 230 ±1,6 818 KF-10100AS
125 37 30 140 50 30 25 97 275 ±2 1706 KF-10125AS

Pin for female hinge Pin for narrow female hinge

Including 2 circlips Including circlip

Material: Zinc-plated steel Material: Zinc-plated steel

Ø FF FL FM Mass Part no.* Ø A C D E F G H L B Mass Part no.

f8 g H12 +0,5
+0,3 h13 f7 h11 0
-0,5
32 10 53 46 30 KF-18032 32 3 32,5 1,1 10 9,6 4 41 14 4,5 26 KF-18032S
40 12 61,3 53 50 KF-18040 40 4 38 1,1 12 11,5 4 48 16 6 42 KF-18040S
50 12 69 61 50 KF-18050 50 4 43 1,1 16 15,2 5 54 20 6 0 84 KF-18050S
-1
63 16 80,5 71 120 KF-18063 63 4 49 1,1 16 15,2 5 60 20 6 94 KF-18063S
80 16 100,5 91 150 KF-18080 80 4 63 1,3 20 19 6 75 24 6 184 KF-18080S
100 20 122,5 111 290 KF-18100 100 4 73 1,3 20 19 6 85 24 6 208 KF-18100S
125 25 140 131 1530 KF-18125 125 6 94 1,6 30 28,6 7 110 36 9 0 606 KF-18125S
-2
* = Pin for part no. KF-10...

Subject to change STANDARDS-BASED CYLINDERS 1.1

15
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Rear male hinge (ISO MP4)

Material: Aluminium
Z = Stroke
Ø CD E EW L MR1 XD Mass Part no.
H9 min. g
32 10 48 26 -0,2 / -0,6 12 15* 142 ±1,25 80 KF-11032
40 12 54 28 -0,2 / -0,6 15 18* 160 ±1,25 100 KF-11040
50 12 65 32 -0,2 / -0,6 15 20* 170 ±1,25 170 KF-11050
63 16 75 40 -0,2 / -0,6 20 23* 190 ±1,6 250 KF-11063
80 16 95 50 -0,2 / -0,6 20 27* 210 ±1,6 420 KF-11080
100 20 115 60 -0,2 / -0,6 25 29,5* 230 ±1,6 660 KF-11100
125 25 140 70 -0,5 / -1,2 30 26 275 ±2 1500 KF-11125
* = Non-standard dimension

Articulated rear male hinge (ISO MP6)

Material: Aluminium Z = Stroke

Ø CC CD DA DB DC DE DF Mass Part no.
H9 g
32 48 10 15 142 14 10,5 14 100 KF-11032S
40 54 12 18 160 16,5 12 16 200 KF-11040S
50 65 12 20 170 17,5 12 16 300 KF-11050S
63 75 16 21 190 21,5 15 21 350 KF-11063S
80 95 16 27 210 24 15 21 1600 KF-1 1080S
100 115 20 29,5 230 28 18 25 700 KF-11100S
125 140 30 40 275 30 25 37 1410 KF-11125S

Front/rear flange (ISO MF1-MF2)

> Rear assembly > Front assembly

Material: Zinc-plated steel Z = Stroke

Ø E ØFB MF R TF UF W ZF Mass Part no.
H13 ± 0,2 JS14 JS14 Max g
32 45 7 10 32 64 80 16 ±1,6 130 ±1,25 200 KF-12032
40 52 9 10 36 72 90 20 ±1,6 145 ±1,25 250 KF-12040
50 65 9 12 45 90 110 25 ±2 155 ±1,25 500 KF-12050
63 75 9 12 50 100 120 25 ±2 170 ±1,6 650 KF-12063
80 95 12 16 63 126 150 30 ±2 190 ±1,6 1500 KF-12080
100 115 14 16 75 150 170 35 ±2 205 ±1,6 2200 KF-12100
125 140 16 20 90 180 205 45 ±2,5 245 ±2 4100 KF-12125

1.1 STANDARDS-BASED CYLINDERS Subject to change

16
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Angle bracket (ISO MS1)

Material: Zinc-plated steel Z = Stroke

Ø ØAB AH AO AT AU E SA TR XA Mass Part no.
H13 JS15 ±0,2 JS14 g
32 7 32 6 4 24 45 142 ±1,25 32 144 ±1,25 55 KF-13032
40 9 36 8 4 28 52 161 ±1,25 36 163 ±1,25 80 KF-13040
50 9 45 10 5 32 64 170 ±1,25 45 175 ±1,25 146 KF-13050
63 9 50 12 5 32 74 185 ±1,6 50 190 ±1,6 175 KF-13063
80 12 63 15 6 41 94 210 ±1,6 63 215 ±1,6 390 KF-13080
100 14 71 20 6 41 114 220 ±1,6 75 230 ±1,6 525 KF-13100
125 16 90 15 8 45 140 250 ±2 90 270 ±2 1040 KF-13125

ISO intermediate hinge (ISO MT4)

CYLINDERS
Material: Zinc-plated steel
Z = Stroke
Ø EA EB L1 R TD TL TM UW XV Mass Part no.
Max min. e9 h14 h14 g
32 82 64 22 0,5 12 12 50 65 73 ±2 20,2 KLF-14032
40 93 72 22 0,5 16 16 63 75 82,5 ±2 34,8 KLF-14040
50 101 79 22 0,5 16 16 75 95 90 ±2 53 KLF-14050
63 107 88 27,5 1 20 20 90 105 97,5 ±2 79,2 KLF-14063
80 123 97 27,5 1,5 20 20 110 130 110 ±2 118,6 KLF-14080
100 131 109 33 1 25 25 132 145 120 ±2 179,2 KLF-14100
125 164 126 33 1 25 25 160 175 145 ±2,5 251,2 KLF-14125
The dimension XV + 1/2 indicates the position of the hinge between the end-caps of the cylinder

Front/rear hinge with floating pin

Material: Zinc-plated steel

Ø AE AL AH AG AF AN A B F G L R Mass Part no.

Max Max e9 h14 h14 h11 ±0,2 +0,2
0 H13 H13 +0,5
0
0
+0,3 g
32 46 14 12 12 50 30 32,5 6,5 6,5 - 6 1 137 KF-14032AP
40 59 19 16 16 63 35 38 9 6,5 10,5 6 1,6 385 KF-14040AP
50 69 19 16 16 75 40 46,5 9 8,5 13,5 8 1,6 513 KF-14050AP
63 84 24 20 20 90 45 56,5 11,5 8,5 13,5 8 1,6 1041 KF-14063AP
80 102 24 20 20 110 45 72 11,5 10,5 16,5 10 1,6 1567 KF-14080AP
100 125 29 25 25 132 55 89 14 10,5 16,5 10 2 3000 KF-14100AP
125 155 32 25 25 160 133 110 - 13,5 20 12 2 2400 KF-14125AP

Subject to change STANDARDS-BASED CYLINDERS 1.1

17
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Counter hinge 90°

Material: Aluminium

Ø CD FA FB FC FD FE FH FI F1 F2 BQ Mass Part no.

H9 g
32 10 32 10 1,2 32,5 46,5 9 6,4 5,5 10,5 26 90 KF-19032
40 12 36 12 2,6 38 51,5 9 6,4 5,5 10,5 28 120 KF-19040
50 12 45 12 0,3 46,5 63,5 9 8,4 5 13,5 32 -0,2 200 KF-19050
63 16 50 16 3,3 56,5 73,5 10,5 8,4 5 13,5 40 -0,6 320 KF-19063
80 16 63 16 1,0 72 93 12 10,5 4,5 16,5 50 580 KF-19080
100 20 73 20 2,5 89 113 13 10,5 4,5 16,5 60 910 KF-19100

Counter hinge 90° (CETOP RP107P)

Material: Aluminium

Ø Q M BG BH BI BL BM BN BO BS BR T G S F BQ Mass Part no.

H13 H13 JS14 Max JS14 JS15 JS14 Max Max Max Max H9 +0,5/0 +0,5/0 g
32 6,6 11 18 31 21 8 32 38 51 10 20 1,6 10 10,5 3 26 56 KF-19032CTA
40 6,6 11 22 35 24 10 36 41 54 15 22 1,6 12 10,5 3 28 139 KF-19040CTA
50 9 15 30 45 33 12 45 50 65 16 26 1,6 12 10,5 3 32 -0,2 142 KF-19050CTA
35 -0,6
63 9 15 50 37 14 50 52 67 16 30 1,6 16 10,5 3 40 200 KF-19063CTA
80 11 18 40 60 47 14 63 66 86 20 30 2,5 16 10,5 3 50 321 KF-19080CTA
100 11 18 50 70 55 17 71 76 96 20 38 2,5 20 10,5 3 60 656 KF-19100CTA
14 20 60 90 70 94 124 30 45 3,2 25 10,5 3 -0,5
125 20 90 70 -1,2
826 KF-19125CTA

1.1 STANDARDS-BASED CYLINDERS Subject to change

18
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Articulated counter hinge (DIN648K)

Material: Aluminium
Ø Q P BG BH BI BL BM BN BO EN ER BQ D H S F Mass Part no.
H13 H13 JS14 Max JS15 JS15 JS14 Max 0/-0,1 Max Max H7 +0,5/0 H13 g
32 6,6 11 18 31 21 10 32 38 51 14 15 10,5 10 8,5 20 3 178 KF-19032SC
40 6,6 11 22 35 24 10 36 41 54 16 18 12 12 8,5 20 3 268 KF-19040SC
50 9 15 30 45 33 12 45 50 65 21 20 15 16 10,5 20 3 458 KF-19050SC
63 9 15 35 50 37 12 50 52 67 21 23 15 16 10,5 20 3 550 KF-19063SC
80 11 18 40 60 47 14 63 66 86 25 27 18 20 11,5 20 3 970 KF-19080SC
100 11 18 50 70 55 15 71 76 96 25 30 18 20 12,5 20 3 1326 KF-19100SC
125 13,5 20 60 90 70 20 90 94 124 37 40 25 30 17 20 3 3000 KF-19125SC

Hinge support

CYLINDERS
Material: Aluminium body and brass bushing
Ø C ØCR FK FN ØHB NH TH UL ØU E f C1 C2 Mass Part no.
H9 f7 ±0,1 ±0,1 ±0,5 g
32 10,5 12 15 30 6,6 18 32 46 11 7 1 71 86 100 KF-41032
40 12 16 18 36 9 21 36 55 15 9 1,6 87 105 150 KF-41040050
50 12 16 18 36 9 21 36 55 15 9 1,6 99 117 150 KF-41040050
63 13 20 20 40 11 23 42 65 18 11 1,6 116 136 234 KF-41063080
80 13 20 20 40 11 23 42 65 18 11 1,6 136 156 234 KF-41063080
100 16 25 25 50 14 28,5 50 75 20 13 2 164 189 435 KF-41100125
125 16 25 25 50 14 28,5 50 75 20 13 2 192 217 435 KF-41100125

Locking unit for ISO cylinders Ø 32 ÷ 125

> ISO protrusion > Reduced protrusion
U U
O

ØMM

ØB

ØB
ØMM
KK

KK
P

TG

DD
N

TG E VD VD
M F WH AM H1 AM

> Additional length to standard rod

S1 for ISO protrusion
S2 for reduced protrusion
S1 S2

Ø AM B DD E F H1 KK M MM N O P S1 S2 TG U VD WH
32 22 30 M6 54,5 84 16 M10 x 1,25 50 12 50 29,5 79,5 85 75 32,5 10 6 26
40 24 35 M6 58 90 15 M12 x 1,25 58 16 58 29,5 87,5 90 75 38 9 6 30
50 32 40 M8 60 100 17 M16 x 1,5 70 20 70 29 99 100 80 46,5 10 6 37
63 32 45 M8 65 110 17 M16 x 1,5 85 20 85 37 122 110 90 56,5 13 6 37
80 40 45 M10 75 125 21 M20 x 1,5 100 25 100 40,5 140,5 125 100 72 16 8 46
100 40 55 M10 90 152 26 M20 x 1,5 116 25 116 59 179 150 125 89 18 8 51
125 54 60 M12 112,5 185 35 M27 x 2 145 32 145 62 207 185 155 110 22 9,5 65

Subject to change STANDARDS-BASED CYLINDERS 1.1

19
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Female fork with clips Articulated self-lubricating fork

Material: Zinc-plated steel Material: Zinc-plated steel

Ø CE CK CL CM ER KK L LE Mass Part no. Ø α° CH KK HA HB HC HD HE HF Mass Part no.
B12 g H7 0 g
-0,12
32 40 10 20 10 16 M10x1,25 26 20 90 KF-15032 32 13 17 M10x1,25 10 43 14 14 20 12,9 76 KF-17032
40 48 12 24 12 19 M12x1,25 32 24 150 KF-15040 40 13 19 M12x1,25 12 50 16 16 22 15,4 110 KF-17040
50 - 63 64 16 32 16 25 M16x1,5 40 32 340 KF-15050 50 - 63 15 22 M16x1,5 16 64 21 21 28 19,3 220 KF-17050
80 - 100 80 20 40 20 32 M20x1,5 50 40 670 KF-15080 80 - 100 14 30 M20 x 1,5 20 77 25 25 33 24,3 400 KF-17080
125 110 30 55 30 45 M27x2 65 54 1790 KF-15125 125 17 41 M27x2 30 110 37 35 51 34,8 1119 KF-17125
Fork with pin suitable for piston rod according to ISO 8140 standard

Fork with axially mounted articulated pin Fork with angle mounted articulated pin

Material: Zinc-plated steel Material: Zinc-plated steel

Ø CH CH1 IA° KK IH IB ID IE IF IG Mass Part no. Ø CH CH1 LG° KK IB ID LA LB LC LD LE LF Mass Part no.
±0,3 g ±0,3 g
32 17 11 30 M10x1,25 19,5 32 15 74,5 35 18 120 KF-22025 32 17 11 50 M10x1,25 32 15 17 37 21 50,5 43 57 110 KF-23025
40 19 17 30 M12x1,25 22 36 17 84 40 20 185 KF-22040 40 19 17 50 M12x1,25 36 17 19 42 27 57,5 50 66 165 KF-23040
50 - 63 22 19 22 M16x1,5 27,5 47 23 112 50 27 360 KF-22050 50 - 63 22 19 40 M16x1,5 47 23 23,5 60 33 79,5 64 84 330 KF-23050
80 - 100 30 24 15 M20x1,5 31,5 58 25 133 63 38 570 KF-22080 80 - 100 30 24 32 M20x1,5 58 25 27 68 40 90 77 99 540 KF-23080
125 - - - - - - - - - - - - 125 - - - - - - - - - - - - - -

Floating joint Piston rod locknut

Material: Zinc-plated steel Material: Zinc-plated steel

Ø CH CH1 ID KK MA MB MC MD ME MF MG MH MI° Mass Part no. Ø KK KV KW Mass Part no.
g g
32 12 19 71 M10x1,25 5 35 20 71 14 22 30 32 8 220 KF-24032 32 M10x1,25 17 6 5 KF-16032
40 12 19 75 M12x1,25 5 35 20 75 14 22 30 32 8 230 KF-24040 40 M12x1,25 19 7 10 KF-16040
50 - 63 20 30 103 M16x1,5 8 54 32 103 22 32 41 45 6 660 KF-24050 50 - 63 M16x1,5 24 8 20 KF-16050
80 - 100 20 30 119 M20x1,5 8 54 40 119 22 32 41 45 6 700 KF-24080 80 - 100 M20x1,5 30 9 30 KF-16080
125 24 54 54 M27x2 10 60 48 147 32 57 65 70 8 2060 KF-24125 125 M27x2 41 12 80 KF-16125

1.1 STANDARDS-BASED CYLINDERS Subject to change

20
 KL Ø 32 ÷ 125 mm - ISO 15552 Pneumatic cylinders UNIVER GROUP

Slot positions for DF magnetic sensor

Supply port side To the right of Opposite to the To the left of

standard supply port side supply port side supply port side
upon request upon request upon request

supply port

Slot positions for DH magnetic sensor - K cylinder series

CYLINDERS
standard
on all sides

Subject to change STANDARDS-BASED CYLINDERS 1.1

21