ACT2802 / ACT2802B

5V/2.5A Backup Battery Pack Manager

FEATURES APPLICATIONS
• Dedicated Single Chip Solution for Mobile Power • Backup Battery Pack
With Minimal Component Count • Power Bank
• 5V/2.5A Constant Output Current Limit in • Mobile Power
Boost Mode • Standalone Battery Charger with USB Output
• 2.5A Switching Charger Current Limit
• Programmable 4.1V to 4.35V Battery Voltage GENERAL DESCRIPTION
• 95% Boost Efficiency (Vbat=4.1V) ACT2802/ACT2802B is a space-saving and high-per-
• Adaptive to 10mA-2400mA Input Sources formance low-profile single-chip solution for backup bat-
tery pack and standalone battery charger.
• Battery Disconnection at Output Short ACT2802/ACT2802B integrates all the functions that a
• <10µA Low Battery Leakage Current at HZ Mode backup battery pack needs, including switching charger,
During Storage boost converter and LED indication.
• Boost Auto Turn-off at No Load and Push Button ACT2802/ACT2802B operates at 1.1MHz for switching
Turn-on charger and 0.55MHz for boost converter allowing tiny
• Battery Over Current, Over Voltage, Over external inductor and capacitors. ACT2802/ACT2802B
Temperature and Short Circuit Protections provides a direct power path from input to output with
• Boost Auto Startup with Load Detection programmable current limit while providing power to
switching charger. Output has higher priority than bat-
• Up to 3.0A Input Current Limit with Prioritized tery charger if the programmed input current limit is
Power Path to Output reached.
• 5V+/-100mV Output Voltage in Boost Mode
ACT2802/ACT2802B charges battery with full cycle of
• 1.1MHz/0.55MHz Switching Frequencies preconditioning, fast charge with constant current and
• 2.2uH Inductor and Low Profile Ceramic Capacitor constant voltage until end of charge. The battery
charger is thermally regulated at 110°C with charge cur-
• 4 LEDs Battery Level and Status Indication
rent foldback.
• Battery Impedance Compensation
ACT2802/ACT2802B boost converter steps battery
• Full Cycle of Battery Charge Management Precondi- voltage up to 5V. Boost converter features high effi-
tioning, Fast Charge, Top off and End of Charge ciency, constant current regulation, short circuit
• Charge Current Foldback at 110°C Die Temperature protection and over voltage protection.
• IC Over Temperature Protection at 160°C ACT2802/ACT2802B provides 3.5mA constant currents
• QFN4x4-24 Package to drive 4 LEDs to indicate battery level and charge sta-
tus. Battery impedance is compensated for battery level
indication.

Data Sheet Rev. H, January 2020| Subject to change without notice 1 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Vbat

Vin LED1 LED2 LED3 LED4 BAT Vout

VIN VOUT
RIMC TH

BLVS ACT2802 SW
Vbat
R7 S1 L1 2.2uH
2.7Ω PB CSP
Rcs
25mΩ C3
PG ND CSN 2*22µF
C1 AGND HZ BTV ILIM IOST ICST 10V
NTC
4.7uF C2
10V R1 R2 R3 R4
R5
80k
R6
60k
25k 750Ω 93.1k 43.2k 22uF
10V

GND

ORDERING INFORMATION
LEDS LATCH BOOST
PB TURN
ALWAYS OFF AT LIGHT
PART NUMBER OUTPUT FLASHLIGHT OFF PACKAGE
ON IN BOOST LOAD
BOOST
BOOST UVLO OFF TIME
ACT2802QL-T1028 5V/2.5A No Yes No Yes 16s QFN44-24

ACT2802BQL-T1028 5V/2.5A Yes No Yes Yes 16s QFN44-24

PIN CONFIGURATION

Data Sheet Rev. H, January 2020| Subject to change without notice 2 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

PIN DESCRIPTIONS
PIN NAME DESCRIPTION
Boost/high-Z mode enable pin, internally pulled up by a 3MΩ resistor to battery. When HZ pin is
1 HZ
pulled ground, boost is enabled if VIN is not present.
Push button input, connect a push button from this pin to AGND, internally pulled up by a 3MΩ
2 PB resistor to battery. PB starts up boost converter if HZ pin is grounded and VIN is not present. For
ACT2802B, if this pin is pushed for 3s, flashlight is enabled.
3 AGND Logic Ground. AGND must be connected to PGND externally through ground plane.
Drive external P-FET to protect output short circuit and leakage during shutdown. nPG pin is pulled
4 nPG
up to VOUT internally. nPG pin is pulled low if VOUT is in the range.
Input current limit setting pin. Connect a resistor from this pin to AGND to set the input current limit.
5 ILIM
The current setting ranges from 1.0A-3.0A.
6 VIN USB or AC adaptor input. When VIN is valid, charge and power path is enabled.
Output pin. Bypass to PGND with a high quality low ESR and ESL ceramic capacitor placed as
7, 8 VOUT
close to the IC as possible.
9, 10 SW Internal switch to output inductor terminal.
Power ground. PGND is connected to the source of low-side N-channel MOSFET and the
11 PGND
MOSFET’s gate driver. PGND must be connected to AGND externally through ground plane.
Battery input. Connected to the battery pack positive terminal to provide power in High-Z mode.
12 BAT
Bypass to PGND with a high quality ceramic capacitor placed as close to the IC as possible.
Positive terminal of charge current sense input. Kevin sense is required with 10nF ceramic
13 CSP
capacitor right across CSP and CSN pins.
14 CSN Negative terminal of charge current sense input.
Output current setting. Connect a resistor from this pin to AGND to set output constant current. The
15 IOST
current setting ranges from 1.0A-2.5A.
Fast charge current setting pin. Connect a resistor from this pin to AGND to set the charge current.
16 ICST
The current setting ranges from 1.0A-2.5A.
Battery termination voltage setting. Connect a resistor from this pin to AGND to program battery
17 BTV
charge termination voltage.
18 LED1 Battery level indicator. An internal 3.5mA sink current limit is built in.

19 LED2 Battery level indicator. An internal 3.5mA sink current limit is built in.

20 LED3 Battery level indicator. An internal 3.5mA sink current limit is built in.

21 LED4 Battery level indicator. An internal 3.5mA sink current limit is built in.
Battery impendence compensation input. Connect to a resistor from this pin to APNG to program
22 RIMC
the battery impedance.
Battery level voltage shift. Connect a resistor from this pin to AGND to shift the battery LED
23 BLVS
indication thresholds.
TH: ACT2802QL-T1028
Temperature sensing input. Connect to battery thermistor terminal. If no use, put 10K pulled down
24 TH/FLD resistor.
FLD: ACT2802BQL-T1028
Open-drain flashlight driver. A internal switch can handle up to 50mA
25 EP Exposed pad. Must be soldered to ground on the PCB.

Data Sheet Rev. H, January 2020| Subject to change without notice 3 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

ABSOLUTE MAXIMUM RATINGS

PARAMETER VALUE UNIT
All the Pin to PGND and AGND -0.3 to 6.5 V

Junction to Ambient Thermal Resistance 40 °C/W

Maximum Power Dissipation 2.5 W

Operating Ambient Temperature -40 to 85 °C

Operating Junction Temperature -40 to 150 °C

Storage Junction Temperature -40 to 150 °C

Lead Temperature (Soldering, 10 sec) 300 °C

: Do not exceed these limits to prevent damage to the device. Exposure to absolute maximum rating conditions for long periods may affect
device reliability.

Data Sheet Rev. H, January 2020| Subject to change without notice 4 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

ELECTRICAL CHARACTERISTICS
(VIN = 5V, TA = 25°C, unless otherwise specified.)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Input Current Limit
Input Voltage Range 4.5 5.5 V
VIN Over Voltage Protection VIN rising, VIN_OVP 5.5 6.0 6.5 V
Input Voltage Validation Time VIN_UVLO<VIN<VIN_OVP 32 ms
Input Current Limit Setting Range RILIM=0.806kΩ - 2.4kΩ 1.0 3.0 A
Input Current Limit RILIM=0.806kΩ 3.0 A
Input Current Limit Gain 2000
Leakage Current from VOUT to VIN in
3.0V<VBAT<4.35V, Ta=25°C 0 10 µA
Boost Mode
Battery Discharge Current in High-Z Mode 3.0V<VBAT<4.35V, Ta=25°C 7.5 15 µA
Power Switches
VIN-to-VOUT FET on Resistance 80 mΩ
VOUT-to-SW FET on Resistance 60 mΩ
SW-to-PGND FET on Resistance 65 mΩ
Buck Converter
Switching Frequency -15% 1.1 +15% MHz
High Side Switch Peak Current Limit 4.5 6 A
Minimum On-time 100 ns
Over Temperature Protection (OTP) OTP rising 160 °C
OTP Hysteresis OTP falling 35 °C
Charge Mode
Charge Current Setting Range Rcs=25mΩ, RICST=20kΩ - 50kΩ 1.0 2.5 A
Charge Current Setting (ICHRG) Rcs=25mΩ, RICST=43.2kΩ 2.1 A
Thermal Regulation Temperature 110 °C
Battery Adjust Voltage(VBAJ) Rbtv=25kΩ 0.1 V
End of Charge (EOC) Voltage -0.5% 4.1+VBAJ 0.5% V
EOC Voltage Accuracy Rbtv=0 4.1 V
Battery Over Voltage Threshold VBAT rising 4.6 V
Battery Over Voltage Threshold Hysteresis VBAT falling 200 mV
Fast Charge Current VBAT=3.5V ICHRG A
Precondition Charge Current 2.4V≤VBAT≤2.8V, Percent of ICHRG 10 %
Precondition Voltage Threshold VBAT rising, Rbtv=0 2.8 V
Precondition Voltage Threshold Hysteresis 130 mV
Low VBAT Charge Current VBAT=1V, RICST=43.2kΩ 200 mA
VBAT=4.2V, percent of the fast
EOC Current Threshold 15 %
charge current

Data Sheet Rev. H, January 2020| Subject to change without notice 5 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

ELECTRICAL CHARACTERISTICS
(VIN = 5V, TA = 25°C, unless otherwise specified.)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Charge Restart Voltage Threshold 200 mV
Cold detect NTC thermistor,
TH Upper Temperature Voltage Threshold 1.5 V
ACT2802QL-T1028
Hot detect NTC thermistor,
TH Lower Temperature Voltage Threshold 0.3 V
ACT2802QL-T1028
TH Hysteresis ACT2802QL-T1028 50 mV
TH Internal Pull-up Current ACT2802QL-T1028 60 µA
LED Flash Frequency LED flash 1s on and 1s off 0.5 Hz
Charge Current Foldback
Charge Current Reduction Threshold1
Starting foldback point 4.59 4.7 4.81 V
of Vout1
Charge Current Reduction Threshold2 Stop foldback point, RCS=25mΩ,
4.57 V
of Vout1 RICST=43.2kΩ
Boost Mode
Input Voltage Operation Range 3.0 4.5 V
Switching Frequency -15% 0.55 +15% MHz
Input Voltage UVLO VBAT rising 3.3 V
Input Voltage UVLO Hysteresis VBAT falling 400 mV
Output Voltage (VOUT) Ta=25°C 4.97 5.05 5.10 V
Output Voltage Accuracy All conditions -3 VOUT 2 %
80mA-1A-80mA, 0.1A/us 4.75 5.25 V
Output Voltage Transient Response
1A-2.0A-1A, 0.1A/us 4.7 5.25 V
Output Over Voltage Protection VOUT rising 5.7 V
Output Over Voltage Protection Hysteresis VOUT falling 300 mV
Output Current Regulation Range Rcs=25mΩ, RIOST=37.4kΩ - 93.7kΩ 1.0 2.5 A
Output Current Limit Rcs=25mΩ, RIOST=91kΩ 2.4 A
Maximum Voltage Across VRcs All conditions 200 mV
Minimum On-Time 100 ns
Low Side Switch Peak Current Limit VBAT=3.6V, VOUT=5V 5.6 6.8 A
Soft-Startup Time 400 µs

Under Voltage Protection VOUT falling 4.25 V

(UVP Threshold) VOUT rising 4.6 V
UVP Blanking Time During Startup 3 ms
UVP Sense Detection Time VOUT falling 20 µs

Data Sheet Rev. H, January 2020| Subject to change without notice 6 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

ELECTRICAL CHARACTERISTICS
(VIN = 5V, TA = 25°C, unless otherwise specified.)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Restart After UVP Hiccup mode 2 s
Light Load Current Shut off Threshold VBAT=3.7V, Rcs=25mΩ, RIOST=91kΩ 40 100 mA
Light Load Current Detect Time 16 s
HZ Pin High Voltage HZ voltage rising 0.9 1.4 V
HZ Pin Low Voltage HZ voltage falling 0.4 0.75 V
HZ Internal Pull-up Resistor 3 MΩ
PB Turn off Boost Time ACT2802QL-T1028 1.5 s
PB Turn on Boost Time All condition 30 ms
PB is pushed and released,
LED Indication Time 5 s
ACT2802QL-T1028
Mode Transition
Transition Waiting Time between Charge
TRANTIME 2 s
Mode and Boost Mode
Battery Level Indication
Battery Impedance Compensation Range 40 500 mΩ
Battery Impedance Compensation Rcs=25mΩ, RIMC=200kΩ 200 mΩ
PB High Input Voltage PB voltage rising 0.9 1.4 V
PB Low Input Voltage PB voltage falling 0.4 0.75 V
PB Internal Pull-up Resistor 3 mΩ
Flashlight Driver
Flashlight Voltage UVLO Flashlight rising, ACT2802BQL-T1028 3.3 V
Flashlight Voltage UVLO Threshold Flashlight falling, ACT2802BQL-T1028 2.9 V
Flashlight Driver Current Current at FLD pin, ACT2802BQL-T1028 50 mA
PB Turn on Flashlight Time ACT2802BQL-T1028 3.0 s
PB Turn off Flashlight Time ACT2802BQL-T1028 3.0 s

Data Sheet Rev. H, January 2020| Subject to change without notice 7 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

FUNCTIONAL BLOCK DIAGRAM FOR ACT2802QL-T1028

Q1 Body
5V VIN
VIN
80m Ω Control
VOUT
5V

COUT

UVLO
Current limit
Q2
ILIM
60m Ω
BLVS L1
2.2µH Rcs
Driver SW
PWM Controller
RIMC
Power Management
VBAT +
CSP
-
LED4

CSN
LED3
Battery Level VBAT
Indication BAT
LED2
Q3

LED1
65m Ω TH

PB HZ BTV ICST IOST AGND PGND

CBAT NTC

FUNCTIONAL BLOCK DIAGRAM FOR ACT2802BQL-T1028

Q1 Body
5V VIN
VIN
80m Ω Control
VOUT
5V

COUT

UVLO
Current limit
Q2
ILIM
60mΩ

BLVS L1
2.2µH Rcs
Driver SW
PWM Controller
RIMC
Power Management
VBAT +
CSP
-
LED4

CSN
LED3
Battery Level
Indication BAT
LED2
Q3

LED1
65m Ω FLD

VBAT
PB HZ BTV ICST IOST AGND PGND

CBAT

Data Sheet Rev. H, January 2020| Subject to change without notice 8 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

FUNCTIONAL DESCRIPTION ACT2802B system operation flow chart as shown in Fig-

ure 2.
ACT2802/ACT2802B is a complete battery charging
and discharging power management solution for appli- Any transitions between boost mode and charge mode
cations of single-cell lithium-based backup battery pack go through HZ mode by turning off all the switches Q1-
or power bank. There is a power path from input to out- Q3 into HZ mode for 2 seconds before enabling the
put with programmable input current limit. When output other mode.
is over loaded, the input switch Q1 starts going into lin- The modes are determined by HZ pin and VIN pin
ear mode and thus output voltage starts to drop. If out- as shown in the table 1. A valid VIN voltage forces
put voltage drops below 4.25V, the input switch Q1 ACT2802/ACT2802B into charge mode. Boost mode is
turns off and restart in 2 seconds. enabled if HZ pin is pulled low and VIN is invalid or not
With the advanced ACT2802/ACT2802B architecture, a present. For ACT2802/ACT2802B, when HZ=0, if PB is
synchronous buck/boost converter is connected from pulled low more than 30ms, boost converter is enabled.
VOUT to switching node (SW). With the bidirectional ar- For ACT2802, during boost on, if PB is pressed more
chitecture, the converter could be configured as either than 1.5s, boost converter will be off.
buck to charge battery or boost to discharge battery. Table 1: Mode Selection
With switching charger and discharger, the higher
charge current and higher conversion efficiency are HZ PIN 0 0 1 1
achieved. VIN Valid 0 1 0 1

Modes of Operation Mode Boost Charge HZ Charge

ACT2802/ACT2802B has 3 operation modes: charge

mode, boost mode and high-impedance (HZ) mode. In Flashlight
charge mode, the input current limit Q1 is enabled and ACT2802B has a flashlight function. Once PB is
Q2 and Q3 operate as a buck converter to charge bat- pressed for more than 3 seconds, the flashlight is
tery. In boost mode, Q2 and Q3 operate as boost con- switched on. The driver will deliver up to 50mA current
verter to step battery voltage up to +5V at VOUT, and to the flashlight. During flashlight on, if PB is pressed for
the current limit switch Q1 is turned off, and the reverse 3 seconds, flashlight will be switched off.
current from VOUT to VIN is blocked. In HZ mode, all
the switches are turned off and the drainage current
from battery is very low. ACT2802 system
operation flow chart as shown in Figure 1, and

Figure 1:
ACT2802 System Operation Flow Chart

Data Sheet Rev. H, January 2020| Subject to change without notice 9 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

FUNCTIONAL DESCRIPTION
Figure 2:
ACT2802B System Operation Flow Chart

Latch-Off Precondition Charge

ACT2802QL/ACT2802BQL have latch off function. If A new charging cycle begins with the precondition state,
discharging stops due to battery cut-off, and latch off will and operation continues in this state until VBAT exceeds
be triggered, it would prevent battery from discharging the precondition threshold voltage. When operating
again, latch-off is released when input power is recycled. in precondition state, the cell is charged at a reduced
current, 10% of the programmed maximum fast charge
Input Current Limit constant current. Once VBAT reaches the precondition
When the input current reaches the programmed value, threshold voltage the state machine jumps to the fast
switch Q1 goes into linear mode and output voltage charge state.
starts to drop. When output voltage drops to 4.25V,
hiccup mode is triggered and switch Q1 turns off and Fast Charge
restart in 2 seconds. If battery voltage is above preconditioning threshold,
buck converter charges battery with constant current. In
Switching Battery Charger fast charge state, the ACT2802/ACT2802B charges at
ACT2802/ACT2802B is configured in charge mode the current set by the external resistor connected at the
(buck mode) when VIN is valid. In this mode, a battery ICST pin. During a normal charge cycle fast charge con-
is charged with preconditioning, fast charge, top-off and tinues in CC mode until VBAT reaches the charge termi-
end of charge (EOC). The typical charge management nation voltage, at which point the ACT2802/ACT2802B
is shown in Figure 3 and Figure 4. charges in top off state.
CC/CV Regulation Loop
There are CC/CV regulation loops built in
ACT2802/ACT2802B, which regulates either current or
voltage as necessary to ensure fast and safe charging
of the battery. In a normal charge cycle, this loop regu-
lates the current to the value set by the external resistor
at the ICST pin. Charging continues at this current until
the battery cell voltage reaches the termination voltage.
At this point the CV loop takes over, and charge current
is allowed to decrease as necessary to maintain charg-
ing at the termination voltage.

Data Sheet Rev. H, January 2020| Subject to change without notice 10 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Top Off End of Charge

With the battery voltage approaches the EOC voltage When charge current decreases to 15% of set fast
set by the BTV pin. Charge current decreases as charge current, the buck converter goes into end of
charging continues. In the top off state, the cell is charge mode and keep monitoring the battery voltage.
charged in constant voltage (CV) mode. During a
normal charging cycle charging proceeds until the
Recharge
charge current decreases below the end of charge When battery voltage drops by 200mV below the end of
(EOC) threshold, defined as 15% of fast charge current. charge voltage, the charger is reinitiated with constant
When this happens, the state machine terminates the current charge.
charge cycle and jumps to the EOC state.

Figure 3:
Typical Li+ Charge Profile and ACT2802/ACT2802B Charge States

VEOC

RECHARGE
FAST CHARGEB CURRENT
A: PRECONDITION STATE
Current
Voltage B: FAST-CHARGE STATE
VPRECHARGE C: TOP-OFF STATE
D: END-OF-CHARGE STATE
END-OF-CHARGE CURRENT
PRECONDITION CHARGE CURRENT

STATE
A B C D B

Figure 4:
Charge State Diagram

ANY STATE

BATTERY PLACED AND (VIN > VBAT)

AND (V IN > UVLO) AND (VIN < VOVP)
AND VBAT ≤ 2.8V

PRECONDITION

VBAT > 2.8V (Typical)

FAST CHARGE

VBAT = V EOC

IBAT > IEOC

TOP OFF
V BAT < VEOC - 200mV

IBAT < IEOC

DELAY

END OF CHARGE

Data Sheet Rev. H, January 2020| Subject to change without notice 11 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

APPLICATIONS INFORMATION AGND as shown in Figure 6. The following equation

shows the LED4 voltage threshold:
Battery Charge Termination Voltage
Battery charge termination voltage is set by a resistor = 3.5 + 0.01 × (2)
Rbtv connected from BTV pin to AGND as shown in
Input Output
Figure 5. The battery charge termination voltage is VIN VOUT
estimated as the following equation: Cout

L Rcs
= 4.1 + × 4 × 10 (1) SW
RBLVS
BLVS Battery
Rbtv is selected based on the battery voltage rating. 1%
BAT
accuracy resistor is recommended for Rbtv.
Input VIN Output Figure 6. Battery level voltage shift setting circuit
Io Cout As long as LED4 is set, all the other 3 LED thresholds
is fixed as shown in the table 3:
L Rcs
Rbtv SW
BTV
Table 3: 4 LED Voltage Thresholds
Battery
CSP RBLVS (ohm) 50K 60K 70K 80K
CSN
LED1 3.55V 3.65V 3.75V 3.85V
LED2 3.65V 3.75V 3.85V 3.95V
Figure 5. Battery terminal voltage setting circuit LED3 3.80V 3.90V 4.00V 4.10V

LED Status Indication LED4 4.00V 4.10V 4.20V 4.30V

4 LEDs ON/OFF and flash show the charge status and

the remained capacity level as shown in the table 2. The
Input Current Limit
LED status is based on battery voltage and operation An external resistor is used to set the input current limit
modes. In charge mode, when a battery is fully charged, connected from ILIM pin to AGND as shown in Figure 7.
flashing stops and all the 4 LEDs are solid on. Input current limit has built-in soft startup and current
foldback control loop. The input current limit is
Battery level voltage shift (BLVS pin) estimated as the following equation:
LED1-4 voltage thresholds are adjusted from HZ mode
during charging and discharging based on the 2.4
. = (3)
compensated impedance. Those thresholds are
programmed by a resistor connected from BLVS pin to

Table 2: LED Indication

(Boost or HZ Mode)
Charge Mode
ACT2802QL-T1028 : PB time > 30ms
LED LED1 LED2 LED3 LED4 LED1 LED2 LED3 LED4
VBAT<2.9V Flash Off Off Off Off Off Off Off
2.9V≤VBAT<LED1 Flash Off Off Off Flash Off Off Off
LED1≤VBAT<LED2 On Flash Off Off On Off Off Off
LED2≤VBAT<LED3 On On Flash Off On On Off Off
LED3≤VBAT<LED4 On On On Flash On On On Off
VBAT≥LED4 On On On Flash On On On On
VBAT≥LED4 (End of Charge) On On On On On On On On

Data Sheet Rev. H, January 2020| Subject to change without notice 12 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Iin Input Output

Output VIN VOUT
VIN VOUT RIN
Input Cout
Cout CIN
Ic
Rcs SW
L Ω RICST
L
Rcs
Ω
RILIM 25m
SW ICST 25m Battery
ILIM CSP
Battery
CSN

Figure 10. Battery fast charge current setting

Figure 7. Input current limit setting circuit

Input current limit at various resistor curve is shown in

Figure 8.

Figure 11. Battery fast charge current setting

Figure 8. Input current limit setting Boost Output Constant Current

Boost output current is set by a resistor connected from
The ILIM pin voltage is proportional to input current until
IOST pin to AGND as shown in Figure 12. The boost
input current is limited, as shown in Figure 9.
output current is estimated as the following equation:

2 %
% = × (5)
3 "$

VOUT Output

Io Cout

Rcs

RIOST
SW
L 25m Ω
IOST Battery

CSP
CSN

Figure 12. Boost output current setting circuit

Figure 9. VILIM VS. input current

Battery Fast Charge Current

Battery fast charge current is set by a resistor
connected from ICST pin to AGND as shown in Figure
11. Figure 12 gives out different fast charge current with
various RICST. The battery fast charge current is
estimated as the following equation:

#
" = 1.25 × (4)
"$

Data Sheet Rev. H, January 2020| Subject to change without notice 13 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Figure 13 gives out boost output current with various Input

VIN VOUT
Output

RIOST. Cout

L Rcs
SW R:
Battery Impedance
RIMC
RIMC IBAT
R
BAT Battery
package

Figure 15. Battery impedance compensation

setting circuit

The battery impedance as shown in the table 4

according to the RIMC and Rcs:
Table 4: Battery Impedance

Figure 13. Boost output current setting RIMC(KΩ) 50 100 200

Battery Rcs=25mΩ 50 100 200
The IOST pin voltage is proportional to output current Impedance
R(mΩ) Rcs=50mΩ 100 200 400
until output current is limited, as shown in Figure 14.
Input Over Voltage Surge
In the case of pure ceramic input capacitor is chosen, if
the input cable is long, stray inductance may cause over
voltage spikes as twice as the steady-state voltage
when input source is plugged in. Below input circuit is
recommended to avoid input voltage surge. R1 resistor
is added in series with capacitor C1 to damp the
potential LC resonance as shown in Figure 16.

Input
VIN
Rcs
L 2.2uH 25mΩ
R1 2.7Ω SW
C1 4.7uF
Figure 14. VIOST VS. output current
BAT
Battery
Battery Impedance Compensation
An external resistor is used to set the impedance from
40mΩ to 500mΩ as shown in Figure 15. RIMC is Figure 16. Input over voltage surge protection
corresponding to battery impedance. Higher RIMC gives circuit
higher compensation voltage which is positively
proportional to battery charge/discharge current. Boost Output Plug-in Auto Detection
Select RIMC based on battery impedance: Figure 17 provides a solution for auto plug-in detection.
VBAT

25 × PB
715K
# = (6) Rcs
L 2.2uH 25mΩ
"$ PB
SW

200K
2.2uF 2.2uF
) BAT
=& ' − × × 10 (7) 715K Battery
VOUT HZ

+
D-
COUT
D+
-
USB Shielding Ground

Figure 17. Boost output auto detection circuit

Data Sheet Rev. H, January 2020| Subject to change without notice 14 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

External Input Over Voltage Protection The threshold is given by:

Considering the maximum voltage rating at VIN pin, 60µA×RNOM×kHOT=0.3V →R NOM×kHOT=5kΩ

=1.5V → R
the external OVP circuit as shown in Figure 18 is
recommended if input voltage may go higher than 7V. 60µA×RNOM×kCOLD NOM×kCOLD=25kΩ

With the enhanced OVP circuit, the design can pass where RNOM is the nominal thermistor resistance at room
UN38.3. temperature, and kHOT and kCOLD are the ratios of the
Si2365EDS thermistor's resistance at the desired hot and cold
Input
VIN thresholds, respectively.
10k 3906 Q2
2.7Ω
Q1 60µA
4.7k VTHH +
D1 4.7uF + Li+ Battery
5.6V - Pack
10k TH

+
NTC
Figure 18. Input over voltage protection -
VTHL
–
Inductor and Capacitor Selection
ACT2802/ACT2802B supports SMD components.
2.2uH inductor is recommended. Input side, 4.7uF ce- Figure 19. Battery thermal circuit
ramic capacitor in series with 2.7Ω resistor are recom-
mended, on battery side, 22uF ceramic capacitor is rec-
ommended while on output side, 3*22uF ceramic ca-
pacitors are recommended.
Battery Temperature Monitoring
ACT2802 continuously monitors the temperature of the
battery pack by sensing the resistance of its thermistor,
and suspends charging if the temperature of the battery
pack exceeds the safety limits.
In a typical application, the TH pin is connected to
the battery pack's thermistor input as shown in Figure
19. The ACT2802 injects a 60µA current out of the
TH pin into the thermistor, so that the thermistor
resistance is monitored by comparing the voltage at TH
to the internal VTHL and VTHH thresholds of 0.3V and 1.5V,
respectively. When VTH > VTHH or VTH < VTHL charging
and the charge timers are suspended. When VTH
returns to the normal range, charging and the charge
timers resume.

Data Sheet Rev. H, January 2020| Subject to change without notice 15 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

PC Board Layout Guidance under the C2 (recommend C2 to use 1206 size).

SW pad is a noisy node switching. It should be
When laying out the printed circuit board, the following
isolated away from the rest of circuit for good
checklist should be used to ensure proper operation of
EMI and low noise operation.
the IC.
6) Thermal pad is connected to GND layer through
1) Arrange the power components to reduce the vias (recommend 4X4 pins and the aperture
AC loop size, VIN pin, Vout pin, SW pin and the is 10mil). Ground plane, PGND and AGND
schottky diode. is single point connected under the
2) Place input decoupling ceramic capacitor C3 ACT2802/ACT2802B thermal pad through vias
and R10 as close to VIN pin as possible. to limited SW area.
Resistor R10 is added in series with capacitor
7) From BAT pin to the Battery positive terminal,
C3 to damp the potential LC resonance.
need to lay the divided line to ensure the battery
3) Use copper plane for power GND for best heat voltage accuracy of sampling.
dissipation and noise immunity.
8) RC snubber is recommended to add across SW
4) Place CSP and CSN capacitor C6 (10nF) close to PGND to reduce SW spike below 7V. 3A /20V
to CSP and CSN pin as possible, use Kevin schottky is added to across VOUT and SW pins.
Sense from sense resistor R2 and R2A to CSP
and CSN pins. 22uF decoupling capacitor is A demo board PCB layout example is shown in the
added close to BAT pin. figure 20.

5) Place the ceramic capacitor C2 and D1 as close

to VOUT and PGND as possible, SW goes

Figure 20. PCB Layout

Bottom Layer

Top Layer

Data Sheet Rev. H, January 2020| Subject to change without notice 16 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

R12

R6

R7

R8

LED4

LED3

LED2

LED1
RIMC

LED4

LED3

LED2
BLVS
TH
HZ
PB LED1
R23 R5
PB BTV
R4
AGND ICST
R13 R11 C11 R3
nPG IOST
C12 R1
ILIM CSN
Input USB
C6
+ VIN CSP

PGND
VOUT

VOUT

BAT
SW
SW
D-
R10
D+
- D2
C3 C2
R18 C8
D1
Q1 R2
+
D- L1
Q3 R9 C16
D+
-
R20 R2A
C7 R21
Output US B

C5 BAT
R15 R17 C13 C14
C4

R14 R16

Figure 21. ACT2802 typical application circuit

(Input current limit 3.0A, fast charge current limit 2.1A, boost output constant current limit 2.4A)

Data Sheet Rev. H, January 2020| Subject to change without notice 17 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Table 5: BOM List

ITEM REFERENCE DESCRIPTION QTY MANUFACTURER

1 L1 Core 6.5*3*3 Dip 2.2uH 6A 1 Sunlord
2 Q1 AO4503, Rdson=19mΩ at VGS = - 4.5 V 1 AOS
3 Q3 MMBT3906 1 Murata/TDK
4 D1 MBR1020VL, 20V/1A Schottky 1 Diodes
5 D2 1N4148, Vf=0.7V, 75V Schottky 1 Murata/TDK
6 C2, C5, C13, C14 Ceramic capacitor, 22uF/10V, X7R, 1206 4 Murata/TDK
7 C3 Ceramic capacitor, 4.7uF/10V, X7R, 1206 1 Murata/TDK
8 C4 Ceramic capacitor, 0.1uF/10V, X7R, 0603 1 Murata/TDK
9 C6 Ceramic capacitor, 10nF/10V, X7R, 0603 1 Murata/TDK
10 C7 Ceramic capacitor, 4.7nF/10V, X7R, 0603 1 Murata/TDK
11 C8, C11, C12 Ceramic capacitor, 2.2uF/10V, X7R, 0603 3 Murata/TDK
12 C16 Ceramic capacitor, 4.7uF/10V, X7R, 0603 1 Murata/TDK
13 R1 Chip Resistor, 750Ω, 1/10W, 1%, 0603 1 Murata/TDK
14 R2, R2A Chip Resistor, 50mΩ, 1/4W, 1%, 1206 2 SART
15 R3 Chip Resistor, 93.1kΩ, 1/10W, 1%, 0603 1 Murata/TDK
16 R4, R15 Chip Resistor, 43.2kΩ, 1/10W, 1%, 0603 2 Murata/TDK
17 R5 Chip Resistor, 25kΩ, 1/10W, 1%, 0603 1 Murata/TDK
18 R6 Chip Resistor, 10kΩ, 1/10W, 5%, 0603 1 Murata/TDK
19 R7 Chip Resistor, 60kΩ, 1/10W, 1%, 0603 1 Murata/TDK
20 R8 Chip Resistor, 80kΩ, 1/10W, 1%, 0603 1 Murata/TDK
21 R9 Chip Resistor, 0.47Ω, 1/8W, 5%, 0805 1 Murata/TDK
22 R10 Chip Resistor, 2.7Ω, 1/4W, 5%, 1206 1 Murata/TDK
23 R11 Chip Resistor, 200kΩ, 1/10W, 5%, 0603 1 Murata/TDK
24 R12,R13 Chip Resistor, 715kΩ, 1/10W, 5%, 0603 2 Murata/TDK
25 R14,R16 Chip Resistor, 49.9kΩ, 1/10W, 5%, 0603 2 Murata/TDK
26 R17 Chip Resistor, 75kΩ, 1/10W, 1%, 0603 1 Murata/TDK
27 R18,R20 Chip Resistor, 100kΩ, 1/10W, 5%, 0603 2 Murata/TDK
28 R21 Chip Resistor, 2.2Ω, 1/10W, 5%, 0603 1 Murata/TDK
29 R23 Chip Resistor, 100Ω, 1/10W, 5%, 0603 1 Murata/TDK
30 LED1,LED2, LED3,LED4 LED, 0603, Blue 4 LED Manu
31 PB Push Button Switch 1 Nikkai Omron
32 USB 10.2*14.6*7mm, 4P 1
33 Micro-USB MICRO USB 5P/F SMTB 1
34 U1 IC, ACT2802QL-T1028, T-QFN 44-24 1 Qorvo

Data Sheet Rev. H, January 2020| Subject to change without notice 18 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

LED
R12

R7

R8
R22

LED4

LED3

LED2

LED1
RIMC

LED4

LED3

LED2
BLVS
FLD
HZ
PB LED1
R23 R5
PB BTV
R4
AGND ICST
R13 R11 C11 R3
nPG IOST
C12 R1
ILIM CSN
Input USB
C6
+ VIN CSP

PGND
VOUT

VOUT

BAT
SW
SW
D-
R10
D+
- D2
C3 C2
R18 C8
D1
Q1 R2
+
D- L1
Q3 R9 C16
D+
-
R20 R2A
C7 R21
Output US B

C5 BAT
R15 R17 C13 C14
C4

R14 R16

Figure 22. ACT2802B typical application circuit

(Input current limit 3.0A, fast charge current limit 2.1A, boost output constant current limit 2.4A)

Data Sheet Rev. H, January 2020| Subject to change without notice 19 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Table 6: BOM List

ITEM REFERENCE DESCRIPTION QTY MANUFACTURER

1 L1 Core 6.5*3*3 Dip 2.2uH 6A 1 Sunlord
2 Q1 AO4503, Rdson=19mΩ at VGS = - 4.5 V 1 Vishay
3 Q3 MMBT3906 1 Panjit
4 D1 MBR1020VL, 20V/1A Schottky 1 Murata/TDK
5 D2 1N4148, Vf=0.7V, 75V Schottky 1 Murata/TDK
6 C2,C5,C13,C14 Ceramic capacitor, 22uF/10V, X7R, 1206 4 Murata/TDK
7 C3 Ceramic capacitor, 4.7uF/10V, X7R, 1206 1 Murata/TDK
8 C4 Ceramic capacitor, 0.1uF/10V, X7R, 0603 1 Murata/TDK
9 C6 Ceramic capacitor, 10nF/10V, X7R, 0603 1 Murata/TDK
10 C7 Ceramic capacitor, 4.7nF/10V, X7R, 0603 1 Murata/TDK
11 C8,C11,C12 Ceramic capacitor, 2.2uF/10V, X7R, 0603 3 Murata/TDK
12 C16 Ceramic capacitor, 4.7uF/10V, X7R, 0603 1 Murata/TDK
13 R1 Chip Resistor, 750Ω, 1/10W, 1%, 0603 1 Murata/TDK
14 R2,R2A Chip Resistor, 50mΩ, 1/4W, 1%, 1206 2 SART
15 R3 Chip Resistor, 93.1kΩ, 1/10W, 1%, 0603 1 Murata/TDK
16 R4,R15 Chip Resistor, 43.2kΩ, 1/10W, 1%, 0603 2 Murata/TDK
17 R5 Chip Resistor, 25kΩ, 1/10W, 1%, 0603 1 Murata/TDK
18 R7 Chip Resistor, 60kΩ, 1/10W, 1%, 0603 1 Murata/TDK
19 R8 Chip Resistor, 80kΩ, 1/10W, 1%, 0603 1 Murata/TDK
20 R9 Chip Resistor, 0.47Ω, 1/8W, 5%, 0805 1 Murata/TDK
21 R10 Chip Resistor, 2.7Ω, 1/4W, 5%, 1206 1 Murata/TDK
22 R11 Chip Resistor, 200kΩ, 1/10W, 5%, 0603 1 Murata/TDK
23 R12,R13 Chip Resistor, 715kΩ, 1/10W, 5%, 0603 2 Murata/TDK
24 R14,R16 Chip Resistor, 49.9kΩ, 1/10W, 5%, 0603 2 Murata/TDK
25 R17 Chip Resistor, 75kΩ, 1/10W, 1%, 0603 1 Murata/TDK
26 R18,R20 Chip Resistor, 100kΩ, 1/10W, 5%, 0603 2 Murata/TDK
27 R21 Chip Resistor, 2.2Ω, 1/10W, 5%, 0603 1 Murata/TDK
28 R22 Chip Resistor, 51Ω, 1/8W, 5%, 0805 1
29 R23 Chip Resistor, 100Ω, 1/10W, 5%, 0603 1
30 LED1, LED2, LED3,LED4 LED, 0603, Blue 4 LED Manu
31 LED Flashlight 1 LED Manu
32 PB Push Button Switch 1 Nikkai Omron
33 USB 10.2*14.6*7mm, 4P 1
34 Micro-USB MICRO USB 5P/F SMTB 1
35 U1 IC, ACT2802BQL-T1028, T-QFN 44-24 1 Qorvo

Data Sheet Rev. H, January 2020| Subject to change without notice 20 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

TYPICAL PERFORMANCE CHARACTERISTICS

(Schematic as show in Figure 21, Ta = 25°C, unless otherwise specified)

Data Sheet Rev. H, January 2020| Subject to change without notice 21 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

TYPICAL PERFORMANCE CHARACTERISTICS CONT’D

(Schematic as show in Figure 21, Ta = 25°C, unless otherwise specified)

Data Sheet Rev. H, January 2020| Subject to change without notice 22 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

TYPICAL PERFORMANCE CHARACTERISTICS CONT’D

(Schematic as show in Figure 21, Ta = 25°C, unless otherwise specified)

Data Sheet Rev. H, January 2020| Subject to change without notice 23 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

PACKAGE OUTLINE AND DIMENSIONS

Top View Bottom View

Side View

Notes

Data Sheet Rev. H, January 2020| Subject to change without notice 24 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.
 ACT2802 / ACT2802B
5V/2.5A Backup Battery Pack Manager

Product Compliance
This part complies with RoHS directive 2011/65/EU as amended by (EU) 2015/863.

This part also has the following attributes:

• Lead Free
Pb
• Halogen Free (Chlorine, Bromine)

Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Web: www.qorvo.com Tel: 1-844-890-8163
Email: [email protected]

For technical questions and application information:

Email: [email protected]

Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.

Copyright 2019 © Qorvo, Inc. | Qorvo® and Active-Semi® are trademarks of Qorvo, Inc.

Data Sheet Rev. H, January 2020| Subject to change without notice 25 of 25 www.qorvo.com
© 2020 Qorvo US, Inc. All rights reserved.