JIS JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association JIS B 1051: (ISO 898-1 : 2013) (JFRI/JSA) Mechanical properties of fasteners made of carbon steel and alloy steel— Bolts, screws and studs with specified property classes— Coarse thread and fine pitch thread ICS 21,060.10 Reference number : JIS B 1051: 2014 (E) PROTECTED BY COPYRIGHT 348B 1051 : 2014 (ISO 898-1 : 2013) Date of Establishment: 1972-06-01 Date of Revision: 2014-09-22 Date of Public Notice in Official Gazette: 2014-09-22 Investigated by: Japanese Industrial Standards Committee Standards Board ‘Technical Committee on Machine Elements JIS B 1051:2014, First English edition published in 2015-02 Translated and published by: Japanese Standards Association Mita MT Building, 3-13-12, Mita, Minato-ku, Tokyo, 108-0073 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority © Jsa 2015 Al rights reserved. Unless otherwise specified, no part of this publication may be reproductd or utilized in any form or by any means, electronic or mechanical, including photocopying and tmicrofilm, without permission in writing from the publisher, Printed in Japan ar PROTECTED BY COPYRIGHTIntroductio 1 2 3 4 5 6 7 8 8.1 8.2 8.3 84 8.5 8.6 9 91 9.2 93 94 9.5 9.6 9.7 98 9.9 9.10 9.11 9.12 9.13 9.14 B 1051 : 2014 (ISO 898-1 : 2013) Contents Scope --rnnnnennnnnnnmnnnnnnennennnnnnnnnneinerereeennnnnnnnt Normative references ‘Terms and definitions Symbols and abbreviated terms «--sssssreeenenee Designation system for property classes: Materials Mechanical and physical properties Applicability of test methods General ~~ Loadability of fasteners " Manufacturer's test/inspection Supplier's test/inspection-- Purchaser's test/inspection --ss--vsenensnninnnsin Feasible tests for groups of fasteners and machined test pieces ~ ‘Test methods wrmnsnirnennenmnenmnnennanennennanennenenneneaien ‘Tensile test under wedge loading of finished bolts and screws (excluding studs) : : : Tensile test for finished bolts, serews and studs for determination of tensile strength, Ry : ee + ‘Tensile test for full-size bolts, serews and studs for determination of elongation after fracture, 4), and stress at 0.004 8d non- Proportional elongation, Ry Tensile test for bolts and screws with reduced loadability due to head design - ‘Tensile test for fasteners with waisted shank Proof load test for finished bolts, screws and studs. Tensile test for machined test pieces Head soundness test ---r--renene Hardness test - Decarburization tests: Carburization test Retempering test ‘Torsional test sore Impact test for machined test pieces 82 @ PROTECTED BY COPYRIGHTB 1051 : 2014 (ISO 898-1 : 2013) 9.15 10 10.1 10.2 10.3 10.4 10.5 Surface discontinuity inspection Marking -. General - Manufacturer’ identification mark Marking and identification of fasteners with fall Toadability Marking and identification of fasteners with reduced loadability Marking of packages -~ Annex A (informative) Relationship between tensile strength and elongation after fracture - Annex B (informative) Influence of elevated temperatures on mechanical Annex C (informative) Elongation after fracture for full-size fasteners, Ay properties of fastener Gi) PROTECTED BY COPYRIGHTB 1051 : 2014 (ISO 898-1 : 2013) Foreword This translation has been made based on the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee as the result of proposal for revision of Japanese Industrial Standard submitted by The Japan Research Institute for Screw Threads and Fasteners (JFRI)/Japanese Standards Association (JSA) with the draft being attached, based on the provision of Article 12 Clause 1 of the Industrial Stan- dardization Law applicable to the case of revision by the provision of Article 14. Consequently JIS B 1051:2000 is replaced with this Standard. This JIS document is protected by the Copyright Law. Attention is drawn to the possibility that some parts of this Standard may confliet with patent rights, applications for a patent after opening to the public or utility model rights. ‘The relevant Minister and the Japanese Industrial Standards Committee are not responsible for identifying any of such patent rights, applications for a patent after opening to the public or utility model rights, Gi) PROTECTED BY COPYRIGHTJAPANESE INDUSTRIAL STANDARD JIS B 1051 : 2014 (SO 898-1 : 2013) Mechanical properties of fasteners made of carbon steel and alloy steel— Bolts, screws and studs with specified property classes—Coarse thread and fine pitch thread Introduction This Japanese Industrial Standard has been prepared based on the fifth edition of ISO 898-1 published in 2013 without any modifications of the technical contents. ‘The portions with dotted underlines are the matters not given in the corresponding International Standard. 1 Scope ‘This Standard specifies mechanical and physical properties of bolts, screws and studs made of carbon steel and alloy steel when tested at an ambient temperature range of 10°C to 35°C, Fasteners (the term used when bolts, screws and studs are considered all together) that conform to the requirements of this Standard are evaluated at that ambient temperature range. They might not retain the specified mechanical and physi- cal properties at elevated temperatures (see Annex B) and/or lower temperatures. NOTE 1 Fasteners conforming to the requirements of this Standard are used in applications ranging from ~50 °C to +150 °C. Users are advised to consult an experienced fastener metallurgist for temperatures outside the range of -50 °C to +150 °C and up to a maximum temperature of +300 °C when determining appropriate choices for a given application. NOTE 2 Information for the selection and application of steels for use at lower and elevated temperatures is given, for example, in EN 10269, ASTM F2281 and in ASTM A320/A320M. Certain bolts and screws might not fulfil the tensile or torsional requirements of this Standard because the geometry of their heads reduces the shear area in the head com- pared to the stress area in the thread. These include bolts and screws having a low or countersunk head (see 8.2), ‘This Standard is applic — made of carbon steel or alloy steel, ble to bolts, screws and studs — having triangular ISO metric serew thread in accordance with JIS B 0205-1, — with coarse pitch thread M1.6 to M39, and fine pitch thread M8x1 to M39x3, — with diameter/pitch combinations in accordance with JIS B 0205-2 and JIS B 0205-3, and — having thread tolerances in accordance with JIS B 0209-1, JIS B 0209-2 and JIS B 0209-4, PROTECTED BY COPYRIGHT