NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
Lab 4: Delta-Wye Conversion
Objectives:
1. To perform Delta-Wye Conversion
2. To verify the results with measured data.
3. Solve a complex circuit using Delta-Wye Conversion.
To verify experimentally the principle of delta-wye and wye-delta transformation.
2. To prove that the delta networks can be transformed into its equivalent Wye or
3. To learn to connect a circuit.
The Delta-Wye transformation is an extra technique for transforming certain resistor
combinations that cannot be handled by the series and parallel equations. This is also referred to
as a Pi - T transformation
Sometimes when you are simplifying a resistor network, you get stuck. Some resistor networks
cannot be simplified using the usual series and parallel combinations. This situation can often
be handled by trying ∆ − 𝑌 transformation, or 'Delta-Wye' transformation.
The names Delta and Wye come from the shape of the schematics, which resemble letters. The
transformation allows you to replace three resistors in a Δ configuration by three resistors in a
Y configuration, and the other way around.
The∆ − 𝑌drawing style emphasizes these are 3-terminal configurations. Something to notice is
the different number of nodes in the two configurations. Δ has three nodes, while Y has four
nodes (one extra in the center).
The configurations can be redrawn to square up the resistors. This is called π−T configuration,
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
The π−T style is a more conventional drawing you would find in a typical schematic. The
transformation equations developed next apply to π−T as well.
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
The transformed network and the original network has the same equivalent resistance (although
the individual resistors between the nodes are different).The two networks will be electrically
identical as measured from the three terminals (A, B, and C), i.e. the node voltages of both the
circuits would be equal.
Circuit Diagram:
Circuit 1
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
Circuit 2
List of Equipment
● Trainer Board
● DMM
● 5 x 15kΩ resistor
● 3 x 5 kΩ resistor
Procedure
1. Measure the resistor values with DMM and note down in Table 1.
2. Setup the circuit as shown in the circuit 1
3. Measure the voltage 𝑉𝐴𝐷 , 𝑉𝐵𝐷 , 𝑉𝐶𝐷 (D is the reference node) and note down in Table 2
4. Measure the voltage 𝑉𝐴𝐵 , 𝑉𝐵𝐶 , 𝑉𝐴𝐶 and note down in Table 2
5. Setup Circuit 2.
6. Measure the voltage 𝑉𝐴𝐷 , 𝑉𝐵𝐷 , 𝑉𝐶𝐷 (D is the reference node) and note down in Table 2
7. Measure the voltage 𝑉𝐴𝐵 , 𝑉𝐵𝐶 , 𝑉𝐴𝐶 and note down in Table 2
Data Collection for Lab4:
Group No. ________
NORTH SOUTH UNIVERSITY
DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING
EEE41L/ETE141L
Instructor’s Signature __________
Table 1:
Theoretical R Measured R % Error
15k
5k
Table 2:
Readings Circuit 1 Circuit 2 % Error
𝑉𝐴𝐷
𝑉𝐵𝐷
𝑉𝐶𝐷
𝑉𝐴𝐵
𝑉𝐵𝐶
𝑉𝐴𝐶
Report:
1. The resistors in Circuit 1 are in series or in parallel combination?
2. What technique would you use to find the equivalent resistance?
3. Perform Delta-Wye conversion for ∆𝐴𝐵𝐶 (𝑢𝑝𝑝𝑒𝑟 𝑝𝑜𝑟𝑡𝑖𝑜𝑛) of circuit 1. Show all your
steps to find the equivalent resistance R1, R2, R3 from Ra, Rb, Rc.
4. Redraw the equivalent the circuit after applying the Delta-Wye conversion for ∆𝐴𝐵𝐶. Is it
same as circuit 2?
5. Calculate Req.
6. Calculate the voltage of R1, R2, R3.
7. Calculate 𝑉𝐴𝐵 , 𝑉𝐵𝐶 , 𝑉𝐴𝐶 and 𝑉𝐴𝐷 , 𝑉𝐵𝐷 , 𝑉𝐶𝐷 . Do your calculated values match the
measured values for circuit 2? Find the % Error.
8. Using Table 2, analyze whether Circuit 2 is equivalent to Circuit 1? Was Delta-Wye
conversion successful?
