PARTS LIST

2019.08.01
 TABLE OF CONTENTS

Brush drive system 1

Squeegee assembly 3
Vacuum system 5
Frame system 7
Handel bar 9
Chassis system 11
Wiring system 13
Wiring diagram 15
Two- tank version 17
Membrane tank version 19
Solution system 21
Brush drive system 2017.11.02
CA 340 2018.04.04

Resource notes:
POSITION 5. 909 5985 000 IS GOING OUT OF STOCK WILL BE REPLACED BY POSITION 5. 9099950000

1
 Brush drive system 2017.11.02
CA 340 2018.04.04

No. Part No. Qty. Description Part

Note
00 L08425200 1 BRUSH CYL 340MM SOFT NYLON BLUE
00 L08425300 1 BRUSH CYL 340MM GRIT 500 GREY
00 9099521000 1 WEAR PACK KIT [1]
00 9097353000 1 BLADES SQUEEGEE 440MM 17 PU KIT
00 L08603110 1 FILTER VACUUM MOTOR
00 9099522000 1 WEAR PACK SICA BRUSH KIT [1]
00 L08603096 1 PRE FILTER VACUUM MOTOR D 80 T 20 [1]
01 L08603022 2 RING RUBBER [1]
05 9099950000 1 MOTOR BRUSH 115V 50HZ KIT [1]
05 9099665000 1 MOTOR BRUSH [1]
10 L08603750 1 PULLEY ZAMAK TOOTHED W/WASHER CPL [1]
100 L08425200 1 BRUSH CYL 340MM SOFT NYLON BLUE
100 L08425300 1 BRUSH CYL 340MM GRIT 500 GREY
105 L08603005 1 OIL SEAL TYPE N004/14 [1]
110 33006181 2 RING D 52 UNI7437 [1]
115 L08603008 1 SPACER D.25.2X30 H.24.5 GALV. [1]
120 1467640000 2 BEARING BALL 6205 DDU SIP
125 L08603009 1 PULLEY BRUSH SHAFT PLAST. [1]
130 L08603177 1 BELT TIMING HTD 5M A 500
135 L08603001 1 COVER BRUSH MOTOR PLAST.
140 145 1964 000 6 SCREW M6X12 CAP HD HEX SOCK SS ISO4762 [1]
145 9099514000 1 HARDWARE BRUSH FIXING KIT
26 L08603253 1 SHELL SCREWED FOR EL.MOT. [1]
30 L08603023 1 RING RUBBER [1]
35 L08603010 1 HOUSING MOTOR [1]
36 L08603018 4 SPACER 7.5X12X8 [1]
40 L08603016 1 FLANGE BRUSH MOTOR [1]
45 L08603017 4 SPACER [1]
47 4
50 L08812104 4 SCREW M5X18 CAP HD HEX SOCK ISO4762 [1]
55 1466530000 1 WASHER PLAIN M6X18 ISO7093 10 PCS SET
60 33023653 4 SCREW M6X20 HD HEX ISO4762 10PCS.SET
65 L08603241 1 SCREW WING KIT
75 L08812686 2 SPACER 7X18X3 BLACK [1]
80 L08603004 1 BUSH BRUSH FIXING [1]
85 L08095000 1 O-RING 3.53X26.58 -4106- NBR 70SH
90 33023696 1 RING F SHAFT D.5 DIN6799 SET 10 PCS [1]
95 L08603003 1 SHAFT [1]

Part Notes:
[1] - STOCK COVERS GUARANTEE

2
Squeegee assembly 2018.04.04
CA 340 2018.04.04

Resource notes:

3
 Squeegee assembly 2018.04.04
CA 340 2018.04.04

No. Part No. Qty. Description Part

Note
00 9099518000 1 BLADES SQUEEGEE 440MM 17 REAR PU KIT [1]
00 9099515000 1 COVER BRUSH COMPLETE KIT [2]
00 9097353000 1 BLADES SQUEEGEE 440MM 17 PU KIT [3]
00 9099516000 1 COVER BRUSH KIT [4]
00 9099517000 1 BLADES SQUEEGEE 440MM 17 FRONT PU KIT [5]
01 L08603026 1 PANEL FOR BRUSH COVER
05 L08603027 2 ROLLER BUMPER [6]
10 L08220100 2 SCREW SHOULDER 8X16 M6 DIN923 [6]
100 L08603378 2 SCREW 4X20 PAN PHIL W/O BIT 10.9 F PLAST [6]
105 L08812009 1 GUIDE [6]
110 L08603036 1 PIN FOR BRUSH CONTROL LEVER [6]
115 L08603728 1 COVER CYLINDRIC BRUSH GREY PLAST.
120 L08603038 1 HOLDER REAR BLADE
15 L08603039 2 SEAL BLADE HOLDER
20 L08603397 1 HOLDER FRONT BLADE
25 L08603402 2 ROLLER PLAST. F SUPPORT BLADE SQUEEGEE
30 L08812122 2 PIN 6.3X40 UNI6873
35 L08603744 2 SCREW M5X16 PAN HD PHIL SS ISO7045
36 L08603733 2 SCREW M4X40 PAN HD PHIL SS ISO7045 [6]
37 9100001912 1 WASHER PLAIN M4X9SS ISO7089 10 PCS SET
38 L08603685 2 NUT LOCK HEX M4 LOW SS ISO10511
40 L08603040 2 SUPPORT PLAST. F SQUEEGEE BLADES
45 9097353000 1 BLADES SQUEEGEE 440MM 17 PU KIT
55 L08603203 8 SCREW M5X25 C/SUNK RISED PHIL SS ISO7047
60 L08603037 1 SPRING EXTENSION D.E.11 WIRE D.1.25 [6]
65 L08603359 2 SCREW 4X10 PAN PHIL W/O BIT F PLASTIC
70 L08603357 2 HOLDER RUBBER [6]
75 L08603358 2 O-RING 1.78X6.65 -106- NBR 70SH [6]
80 9100002198 1 LEVER BRUSH FIXING KIT [7]
95 L08603031 1 LEVER BRUSH CONTROLLING [6]

Part Notes:
[1] - includes pos.15-35-40-45-50-55-120
[2] - includes pos.1-5-10-15-20-25-30-35-40-45-50-55-65-70-75-115-120-121-122-123
[3] - includes pos.45-50
[4] - includes pos.65-70-75-115-121-122-123
[5] - includes pos.15-20-25-30-40-45-50-55-123
[6] - STOCK COVERS GUARANTEE
[7] - Included Item No.80, 85, 90

4
Vacuum system 2017.11.02
CA 340 2013.04.02

Resource notes:
POSITION 83 NO LONGER AVAILABLE BY THE SUPPLIER

5
 Vacuum system 2017.11.02
CA 340 2013.04.02

No. Part No. Qty. Description Part

Note
00 L08812119 1 TURBINE SET [1]
01 L08601157 2 SCREW 4.9X20 C/SUNK PHIL W/O BIT F PLAST [2]
05 L08603187 1 PLATE GASKET [2]
10 L08603188 1 GASKET PANEL [2]
15 L08603108 1 COVER INSULATION ACOUSTIC PANEL PLAST. [2]
20 L08603104 1 TOP SOUND INSULATION
25 L08603174 1 CLAMP F SOUNDPROOF INSULATION PANEL [2]
30 L08603103 1 BOTTOM SOUND INSULATION [2]
35 L08600269 2 CLAMP 9/25-40 [2]
40 L08603092 1 HOSE SUCTION SQUEEGEE BLACK
55 L08603101 1 SLEEVE RUBBER VACUUM MOTOR [2]
60 L08601663 1 CLAMP 12/32 - 50 [2]
65 L08603102 1 PANEL DAMPER [2]
67 L08603096 1 PRE FILTER VACUUM MOTOR D 80 T 20 [2]
68 L08603097 1 GRATE FILTER PROTECTION PLAST. [2]
70 L08603095 1 SEAL SUCTION HOSE
75 L08603094 1 SEAL [2]
80 L08603098 1 VIBRATION-DAMPING [2]
83 L08812118 1 STRAND WIRE [3]
85 L08603260 1 MOTOR VACUUM 120V 60HZ 5.7 2ST
85 909 5040 000 1 MOTOR VACUUM 230V 50HZ
90 L08603100 1 SEAL VACUUM MOT.FAN SIDE [2]
90 L08812029 1 SEAL [4]
95 L08603110 1 FILTER VACUUM MOTOR

Part Notes:
[1] - TURBINE CPL WITH GASKET - NOT SHOWN
STOCK COVERS GUARANTEE
[2] - STOCK COVERS GUARANTEE
[3] - ITEM NO LONGER AVAILABLE
[4] - GUARANTEE DATE EXPIRED

6
Frame system 2017.11.02
CA 340 2016.05.27

Resource notes:

7
 Frame system 2017.11.02
CA 340 2016.05.27

No. Part No. Qty. Description Part

Note
00 9099520000 1 PEDAL BRUSH LIFTING KIT [1]
01 L08812002 1 FRAME COATED RAL 9005 [2]
01 L08603066 1 FRAME [1]
05 L08603068 2 PLUG F FRAME PLAST. [1]
06 L08603214 1 DECAL INSTRUCTIONS [1]
10 L08603076 2 WHEEL CASTOR D.75X25 GALV. [1]
100 L08603055 2 SPACER D13X19 L.13 BRASS [1]
105 9100001351 1 WASHER PLAIN M8 ISO7089 SS 10 PCS SET
110 L08812803 2 SCREW M8X20 CAP HD HEX SS ISO4762 SCOTCH [1]
115 L08603377 4 SCREW 6X25 PAN PHIL W/O BIT F PLASTIC [1]
15 145 5742 000 2 SCREW M10X20 CAP HD HEX SOCK ISO4762
20 L08603071 1 SPRING TORSION WIRE D.1.25 D.I. 9.25
25 L08603069 1 PIN GALV. FOR PEDAL BLOCK [1]
30 L08603183 4 RING RADIAL D 4 UNI7434 [1]
35 L08603354 1 BLOCK BRUSH PEDAL PLAST. [1]
40 L08603356 1 PIN BRUSH PEDAL [1]
45 L08603075 1 SPRING TORSION SS WIRE D.1.25 D.I. 8.8 [1]
50 L08603061 2 SPRING EXTENSION D.E.20 WIRE D.2.8 [1]
55 L08603062 1 PIN BRUSH LIFT.FRAME [1]
60 9100000701 2 WHEEL D.75X28 GREY KIT
65 L08603057 1 FRAME BRUSH LIFTING [1]
70 L08603181 2 SCREW M8X35 HEX HD SS ISO4017 SCOTCH-GRI [3]
75 9100001351 1 WASHER PLAIN M8 ISO7089 SS 10 PCS SET
80 L08603064 1 SPRING COMPRESSION D.E.12 WIRE D.0.7 [1]
85 L08603065 1 KNOB [1]
90 L08603063 1 SCREW M8X35 HEX HD F/THD SS ISO4017 [1]
91 L08603746 1 CAP PLASTIC BLACK F THREAD M8 [1]
95 L08603355 1 PEDAL BRUSH CONTROL [1]

Part Notes:
[1] - STOCK COVERS GUARANTEE
[2] - GUARANTEE DATE EXPIRED
[3] - ALT.USE KIT 9100000701

8
Handel bar 2017.11.02
CA 340 2017.07.10

Resource notes:

9
 Handel bar 2017.11.02
CA 340 2017.07.10

No. Part No. Qty. Description Part

Note
01 L08603155 1 DECAL CONTROL PANEL [1]
05 L08603231 1 HOUSING SWITCHES KIT W/DECAL [2]
10 L08603244 2 SCREW 3.9X13 SELF PAN HD PHIL ISO7049 [1]
100 L08600168 2 BLOCK CABLE FIXING
105 L08603137 1 RATCHET DISC HANDLE ADJ. SUPPORT [1]
110 L08600149 4 SCREW M6X12 CAP HD HEX ISO4762 SCOTCH-GR [1]
115 L08603144 1 SPRING COMPRESSION D.E.17.6 WIRE D.1.6 [1]
120 L08603138 1 RATCHET DISC HANDLE BAR [1]
125 L08603141 1 KEY 4X4X12 UNI6604A [1]
15 909 5847 000 1 HOUSING SWITCH LOWER PLAST. [1]
20 L08603192 8 SCREW 3.6X16 PAN PHIL W/O BIT F PLASTIC
25 L08603145 1 HANDLE BAR [1]
26 L08601101 1 HOLDER CABLE [1]
30 L08601000 1 NUT LOCK HEX M12 ISO7040 [1]
35 L08603142 1 SPACER 13X18X62 [1]
40 L08603136 1 SUPPORT HANDLE BAR [1]
45 L08603190 2 SCREW M6X50 PAN HD PHIL ISO7045 SCOTCH- [1]
50 33023208 2 WASHER PLAIN M8 ISO7089 10 PCS SET
51 33005851 2 WASHER SPRING LOCK M6 DIN127-B
55 33023669 1 NUT HEX M6 DOMED CAP HIGH 5 PCS SET [3]
60 L08603140 1 SHAFT HANDLE ADJUST.LEVER [1]
65 L08603191 1 SPACER D.13X18 H.32 GALV. [1]
70 L08603143 1 SPACER HANDLE ADJUSTEMENT LEVER [1]
75 33023667 1 NUT LOCK HEX M6 LOW ISO10511 5 PCS SET
85 L08603146 1 LEVER HANDLE ADJUSTING [1]
90 L08603175 1 SCREW M6X25 HEX HD P/THD 4.8 ISO4014 [1]

Part Notes:
[1] - STOCK COVERS GUARANTEE
[2] - ALTERNATIVE USE L08603155 & 909 5846 000
[3] - SEE PI 2017-002

10
Chassis system 2017.11.02
CA 340 2013.04.02

Resource notes:

11
 Chassis system 2017.11.02
CA 340 2013.04.02

No. Part No. Qty. Description Part

Note
00 L08812028 1 HOSE SECTION [1]
01 909 5893 000 8 SCREW 6X60 PAN PHIL W/O BIT F PLASTIC [2]
05 L08603367 1 FRAME UPPER
10 L08603368 1 FRAME LOWER RAL7016 [2]
15 L08603206 4 NUT HEX M8 MEDIUM SS ISO4032 [2]
20 L08603219 2 SCREW M8X30 HEX HD F/THD SS ISO4017 [2]
21 9099431000 1 CHASSIS KIT

Part Notes:
[1] - GUARANTEE DATE EXPIRED
[2] - STOCK COVERS GUARANTEE

12
Wiring system 2017.11.02
CA 340 2013.04.02

Resource notes:
POS. 10 INCLUDES: POSITIONS 10-15-75 POS. 71 NO MORE USED IN THE MACHINE

13
 Wiring system 2017.11.02
CA 340 2013.04.02

No. Part No. Qty. Description Part

Note
00 909 5667 000 1 SWITCH COMPLETE [1]
00 909 5668 000 1 SWITCH ROCKER ORANGE 2 POS. -1 MOM.
01 L08603154 1 CAP PROTECTION
05 L08603153 1 SWITCH PUMP [1]
10 9098694000 1 HARNESS CONTROL PANEL KIT [2]
100 L08348200 1 SCREW 2.9X9.5 SELF PAN HD PHIL ISO7049 [1]
105 L08603912 1 CAPACITOR 0.1UF [1]
20 L08603150 1 GROMMET SLEEVE [1]
25 L08603169 1 CABLE [1]
30 L08603303 1 CAPACITOR 250V 40UF [3]
30 L08603254 1 CAPACITOR 450V [4]
45 L08603196 1 CLAMP 10 CHANNELS [1]
50 909 5667 000 2 SWITCH COMPLETE [1]
60 L08603193 3 COVER SWITCH [1]
65 909 5668 000 1 SWITCH ROCKER ORANGE 2 POS. -1 MOM.
70 909 6231 000 1 CABLE POWER SUPPLY ORANGE COLOUR E [1]
70A 82179200 PLUG UK [5]
70 L08227800 1 CABLE POWER SUPPLY WITHOUT PLUG [1]
80 L08603129 2 GROMMET D.13 BLACK [1]
85 L08093800 1 SCREW 2.9X16 SELF PAN HD PHIL ISO7049 [1]
90 L08603756 1 CABLE BRIDGE UL AWG 18 [1]
95 9099066000 1 RESISTOR KIT [1]

Part Notes:
[1] - STOCK COVERS GUARANTEE
[2] - STOCK COVERS GUARANTEE

INST.INSTR.CODE 9098695000
[3] - FOR 110V VERSIONS
STOCK COVERS GUARANTEE
[4] - FOR 220V VERSIONS
STOCK COVERS GUARANTEE
[5] - ADPTER FOR MAIN CORD CABLE UK

14
Wiring diagram 2017.11.02
CA 340 2013.04.02

Resource notes:

15
 Wiring diagram 2017.11.02
CA 340 2013.04.02

No. Part No. Qty. Description Part

Note

16
Two- tank version 2017.11.02
CA 340 2016.03.21

Resource notes:
position 0 not shown L08812036 valid for machine product numbers L08919552 (L5 2256) POSITIONS 1-25- 30
VALID FOR MACHINES BEFORE SERIAL NUMBER 3810122800029 POSITION 0: 9097737000 valid for machine
CA 340 ET pruned in 31.03.2009

17
 Two- tank version 2017.11.02
CA 340 2016.03.21

No. Part No. Qty. Description Part

Note
00 9097737000 1 DECAL NILFISK CA 340ET [1]
00 l08812036 1 WEIGHT [2]
00 9097736000 1 DECAL NILFISK CA 340 [2]
00 L08603365 1 TANKS TWO WATER KIT [2]
01 1466138000 1 CAP BLACK PPL DE 42X11.5 SIP
05 L08603084 1 COVER PLAST. GREY F WATER TANKS KIT [2]
10 L08603230 1 GASKET BULB RUBBER L.860MM SIP
15 L08603239 1 SPACER D.7X10 H.32 PLASTIC [1]
20 9099506000 1 GRIP RECOVERY TANK KIT [2]
25 L08603255 4 COVER PIN [2]
30 L08603240 1 SPACER 7X10X14 [1]
35 L08603119 1 TANK RECOVERY 12L PLAST. GREY [2]
40 L08603235 1 TANK RECOVERY 12L PLAST. GREY KIT
45 L08603229 1 GASKET BULB RUBBER L.780MM SIP
50 L08092600 1 BALL FLOATING
55 9100001371 1 CAGE FLOAT PLAST. SIP
60 9099505000 1 GRIP SOLUTION TANK KIT [2]
65 L08603117 1 SPACER 7X10X19 [2]
70 L08603240 1 SPACER 7X10X14 [1]
75 L08603118 1 TANK SOLUTION 11L PLAST. GREY
80 L08603234 1 TANK SOLUTION 11L PLAST. GREY KIT

Part Notes:
[1] - GUARANTEE DATE EXPIRED
[2] - STOCK COVERS GUARANTEE

18
Membrane tank version 2017.11.02
CA 340 2016.03.21

Resource notes:
POSITION 40 L08812013 BELONG ONLY TO THE MACHINE L08919552 PRUNED ON THE 12.04.2011
L08919552

19
 Membrane tank version 2017.11.02
CA 340 2016.03.21

No. Part No. Qty. Description Part

Note
00 L08603489 1 TANK WATER GREY W/MEMBRANE KIT [1]
01 L08603228 1 GASKET BULB RUBBER L.1225MM SIP
02 1466138000 1 CAP BLACK PPL DE 42X11.5 SIP
03 9100001371 1 CAGE FLOAT PLAST. SIP
04 L08092600 1 BALL FLOATING
05 L08603123 4 SCREW 3.5X10 PAN PHIL W/O BIT SS F PLAST [2]
10 L08603121 1 FRAME OPEN FOR MEMBRANE [1]
15 L08603122 4 BLOCK MEMBRANE FRAME PLAST. [1]
20 L08603236 2 ROD DRAWN D.4 L.100MM [1]
25 L08603237 2 ROD DRAWN D.4 L.190MM [1]
30 L08603120 1 MEMBRANE FOR 15 LITRES [1]
30 L08812012 1 MEMBRANE FOR 30 LTRES [2]
31 L08603364 1 MEMBRANE 15 LT W/SUP. KIT [1]
31 L08812087 1 MEMBRANE 30 LT W/SUP. KIT [1]
35 L08603400 1 TANK WATER PLAST. GREY [2]
40 L08812013 1 HOSE DRAIN [1]
40 L08603083 1 HOSE DRAIN GREY [2]
45 L08600269 1 CLAMP 9/25-40 [2]
50 L08603745 1 COVER PLAST. GREY F WATER TANKS KIT [2]

Part Notes:
[1] - GUARANTEE DATE EXPIRED
[2] - STOCK COVERS GUARANTEE

20
Solution system 2017.11.02
CA 340 2016.10.06

Resource notes:

21
 Solution system 2017.11.02
CA 340 2016.10.06

No. Part No. Qty. Description Part

Note
00 L08812124 1 PUMP W/NIPPLE 100-125V KIT [1]
00 9100000933 1 PUMP WATER 230V 40W KIT [2]
01 L08603735 1 HOSE CRISTAL D.6X10 L.900MM SIP
01 L08812025 1 HOSE CRISTAL D.6X10 L.1040MM SIP [1]
05 L08603189 1 BARB HOSE 90 D.6 PLASTIC
10 L08603129 2 GROMMET D.13 BLACK [1]
15 9100000733 1 CAP PLASTIC D.42 WHITE WITH HOLE SIP
20 L08812048 1 HOSE CRISTAL D.6X10 L.650MM SIP
20 L08603225 1 HOSE D.6 L.270MM SIP
25 L08603126 1 FILTER SOLUTION
30 L08603131 1 BARB HOSE 90 D.6 1/8 PLASTIC [3]
35 L08603246 2 SPONGE ANTIDUST [4]
40 9100000933 1 PUMP WATER 230V 40W KIT [5]
40 L08603453 1 PUMP W/RESISTOR 110V 50HZ [1]
41 L08603200 2 EL.WIRE FOR PUMP [1]
41 L08603352 2 WIRE WHITE FOR CAPACITOR [1]
45 L08603130 1 BARB HOSE STRAIGHT D.6 1/8 PLASTIC [1]
50 L08603752 1 HOSE SILICON D.6X9 L.250MM SIP [6]
50 9100000960 1 HOSE SILICONE D.6X9 L.290MM SIP [7]
60 L08603133 1 BARB HOSE Y D.6 PLASTIC
65 L08603223 1 HOSE SILICON D.6X9 L.165MM SIP
70 L08603224 1 HOSE SILICON D.6X9 L.95MM SIP

Part Notes:
[1] - STOCK COVERS GUARANTEE
[2] - replace code L08603755 - INTS. INTR. 9100000934
[3] - GUARANTEE DATE EXPIRED
[4] - ITEM NO LONGER AVAILABLE
[5] - INST. INSTR. 9100000934
[6] - UNTIL MACHINE S.N. 3810151000054
[7] - STOCK COVERS GUARANTEE
STARTING MACHINE S.N. 3810151000055

22
© 2018 - Nilfisk A/5