FIRE PROTECTION DELUGE
MODEL 68 DE\HM-MR
DE\HM-MR
Hydraulically Actuated, Manual Reset
Deluge Valve
Hydraulically controlled deluge/pre-action valve,
actuated by the pipeline pressure. The valve
is closed in its normal, set position and
opens when the hydraulic pressure drops in a
pressurized pilot line, limited to 7m above the
valve (for higher pilot lines, see DE\HRV-MR
model sheet). The valve must be manually reset
following automatic actuation. An emergency
manual release valve is fitted as standard.
CERTIFICATION & COMPLIANCE
• ANSI FCI 70-2 Class VI seat leakage class
• UL listed under VLFT category
• Fire tested to EN ISO 6182-5:2006 (2”- 6” only) * General representation of valve
• Lloyd’s & ABS approvals
FEATURES & BENEFITS
• High pressure (PN25/375psi), high flow • Low lifelong maintenance costs due to
deluge systems straightforward design
• Automatic or local manual emergency • Applicable for fresh or brackish water,
actuation seawater & foam
• Out of box fully assembled & tested valves
• Hazardous, flammable & explosion • Factory trimmed for vertical & horizontal
classified area fire suppression installations without modification
• Superior design featuring exceptionally • Extensive valve & trim materials selection
low pressure losses at high flow rates and corrosion protection coating
TYPICAL APPLICATIONS
Automatic or Manual Actuated Flammable Storage
Fire Suppression Systems
Petrochemical, Oil & Gas Hangars & Airport Terminals
Installations
Tunnels Onshore / Offshore
Power Generation, Transformer Mining
& Transmission Plants
1
w w w. c o n t r o l va l v e s . c o m
FIRE PROTECTION DELUGE
MODEL 68 DE\HM-MR
OPERATION
The basic control valve [1] used in this deluge system is a direct sealing elastomeric diaphragm,
hydraulically operated control valve engineered specifically for fire protection systems.
In the standby position, the deluge valve is held closed by the upstream water pressure, trapped in the
valve’s control chamber. The water pressure enters the control chamber through the priming line ball
valve [2], a Y-Type strainer [3], a check valve [4] and a DMR (Manual Reset Latching Device) [5].
Under fire conditions, one (or more) of the automatic sprinklers on the wet pilot line burst. Water is
drained from the deluge valve’s control chamber through the burst sprinklers. The deluge valve opens
instantly and allows water to flow into the pipeline and through the open sprinklers over the protected
area.
Manual emergency actuation is enabled by opening the emergency manual activation valve [6]. The
deluge valve opens instantly and allows water to flow into the pipeline and through the open sprinklers
over the protected area.
When the valve trips open, the DMR isolates the control chamber from the upstream pressure source.
Reconnecting the upstream pressure to enable the deluge valve to close can only be achieved by
pressing the DMR’s knob.
Standby Position Hydraulically Actuated
[6] [6]
[2] [3] [4] [2] [3] [4]
[5] [5]
[1] [1]
Manually Actuated Reset To Close
[6] [6]
[2] [3] [4] [2] [3] [4]
[5] [5]
[1] [1]
Resetting, maintenance and periodic testing instructions must be followed as described in detail in the
2 applicable OCV IOM (Installation, Operation & Maintenance) Manual.
w w w. c o n t r o l va l v e s . c o m
FIRE PROTECTION DELUGE
MODEL 68 DE\HM-MR
TYPICAL MATERIALS
ID Description Standard POG (1) Applications
1 Valve Body See Series 100 Engineering Data (2)
2 Ball Valve Bronze, Stainless Steel Ball Stainless Steel 316
3 Y-Type Strainer Bronze, Stainless Steel Screen Stainless Steel 316
4 Check Valve Bronze Stainless Steel 316
5 DMR (Manual Reset Latching Device) Brass Stainless Steel 316
6 Manual Emergency Valve Bronze Stainless Steel 316
7 Drip Valve Brass Stainless Steel 316
8 Pressure Gauge Stainless Steel Stainless Steel 316
(1) Petrochemical, Oil & Gas
(2) Refer to materials selection guidelines, Engineering Data - Materials: Ductile Iron A-536 65-45-12; Cast Steel A-216 WCB; Cast Steel A-352 LCB; Austenitic
Stainless Steel A-351/CF8M; Super Duplex 2507; Nickel-Aluminum-Bronze B-148 UNS C95800
3 * General representation of valve
w w w. c o n t r o l va l v e s . c o m
FIRE PROTECTION DELUGE
MODEL 68 DE\HM-MR
GENERAL ARRANGEMENT & DIMENSIONS
Valve 2” (50) 2.5” (65) 3” (80) 4” (100) 6” (150) 8” (200) 10” (250)
inch mm inch mm inch mm inch mm inch mm inch mm inch mm
A 9 5/8 243 9 3/16 233 12 3/16 310 14 356 17 3/16 436 20 7/8 530 25 635
AG(1) 9 5/8 243 10 253 13 3/16 336 15 380 17 5/16 440 217/8 556 N/A
B 6 5/8 168 7 3/8 185 7 7/8 200 9 3/8 238 12 1/8 306 14 3/16 360 16 7/8 430
C 4 /16 120
11
4 11/16 120 6 153 6 /8
5
167 7 11/16 196 9 5/16 236 11 3/16 285
D 5 11/16 145 5 11/16 145 5 11/16 145 5 11/16 145 6 3/8 160 7 7/8 200 9 7/8 249
E 8 11/16 221 8 11/16 221 11 3/8 287 11 1/8 283 14 3/8 366 15 3/16 386 16 1/8 409
F 10 3/8 262 10 3/8 262 10 3/8 262 10 3/8 262 10 3/8 262 10 3/8 265 12 1/2 317
* Approximate dimensions
** (1) Grooved model length
* General representation of valve
4
w w w. c o n t r o l va l v e s . c o m
FIRE PROTECTION DELUGE
MODEL 68 DE\HM-MR
TYPICAL INSTALLATION
Hydraulically Actuated,
1
Manual Reset Deluge Valve
2 Wet Pilot Line
3 DMR (Latching Manual Reset Device)
* Not all items pictured reflect products sold by OCV
5
w w w. c o n t r o l va l v e s . c o m
FIRE PROTECTION DELUGE
MODEL 68 DE\HM-MR
TECHNICAL DATA
Temperature: Trim Material:
• Media up to 80°C = 176°F • Bronze/Brass - Copper
• Elastomers suitable for extreme climates • Stainless Steel
available upon request • Monel
Sizes: Optional Components:
• UL Listed Sizes: Model 68: 2”-10” • Spring
• Straight Flow: 2”- 24” • Position Indicator
• Pressure Switch
End Connections: • Alarm Test Trim
• Flanged: • Upstream Drain Valve
ISO-PN16 & ISO-PN25 • Limit/Proximity Switch
ANSI B16.42 & B16.5 Class #150 and #300
Additional options available upon request Items to Specify:
• Grooved: • Electrical features other than standard
Sizes: 2”-8” (24VDC, IP65/NEMA4)
• If explosion proof accessories are
Pressure Rating: required such as solenoids, pressure
• 250 psi for Class #150 switches, etc., please define classifica-
• 375 psi for Class #300 tion
• Control trim material other than standard
Body and Cover Material: • Required standards, certifications and
• Ductile Iron • Stainless Steel approvals
• Cast Steel • NAB
ENGINEERING SPECIFICATIONS
The deluge valve shall be hydraulically operated, direct elastomeric diaphragm-seal, single chamber
weir type. The valve shall consist of three major components: the body, the cover and the diaphragm
assembly. The diaphragm assembly shall be the only moving part. The diaphragm forms a sealed
control chamber in the upper portion of the valve, separating operating pressure from line pressure.
Packing glands, stuffing boxes and dynamic O-ring seals are not permitted and there shall not be shafts,
discs, bearings or pistons operating the valve. No hourglass shaped disc retainers shall be permitted,
and no V-type, U-type or other slotted type disc guides shall be used. The valve shall contain a nylon
reinforced rubber diaphragm, elastic & resilient through its entire surface without vulcanized radial
seals and/or reinforcements. The diaphragm assembly shall not be guided by any shafts or bearings
and shall not be in close contact with other valve parts except for its sealing surface. The deluge
valve shall be fully trimmed, hydrostatically and operationally tested at the factory. Maintenance,
disassembly and reassembly of all the valve’s components shall be made possible on-site and in-line,
without the need to remove the valve from the line. Main valve body and bonnet standard material
shall be Ductile Iron or Cast Steel. Main valve body and bonnet surfaces shall include a fire red epoxy
coating. Other materials and coatings available upon request. The deluge valve shall be a Model 68
DE\HM-MR, UL Listed under VLFT category, as manufactured by OCV Fluid Solutions, Tulsa, OK, USA.
OCV companies worldwide reserve the right to make changes without notice including product specification and con-
figuration, content, description(s), dimensions etc. The information herein is subject to change without notice. OCV
shall not be held liable for any errors. All rights reserved. © Copyright by OCV.
7400 East 42nd Place • Tulsa, Oklahoma 74145 • USA
6 Phone: 1-918-627-1942 • Toll Free: 1-888-OCV-VALV (628-8258) • Email:
[email protected] w w w. c o n t r o l va l v e s . c o m
