0% found this document useful (0 votes)
452 views5 pages

205-04 Front Drive Halfshafts - Removal and Installation - Front Halfshaft LH

Uploaded by

CARLOS LIMADA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
452 views5 pages

205-04 Front Drive Halfshafts - Removal and Installation - Front Halfshaft LH

Uploaded by

CARLOS LIMADA
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Page 1 of 5

205-04 Front Drive Halfshafts 2019 Ranger


Removal and Installation Procedure revision date: 11/15/2018

Front Halfshaft LH

Special Tool(s) / General Equipment

205-1047
Protector, Halfshaft Seal

Tire Lever
Removal

NOTICE: Do not hold the halfshaft by the CV joint.

NOTICE: The inner constant velocity (CV) joint must not be bent more than 18°.

NOTE: Removal steps in this procedure may contain installation details.

1. Drain the front differential.


Refer to: Differential Draining and Filling (205-03 Front Drive Axle/Differential, General Procedures).

2. Remove the wheel knuckle.


Refer to: Wheel Knuckle (204-01B Front Suspension - 4WD, Removal and Installation).

3. NOTE: Use care to not cause damage to the components.

Remove the front halfshaft LH.


Use the General Equipment: Tire Lever

http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN... 1/21/2019
Page 2 of 5

4.
1. Remove and discard the circlip.
2. Clean the inner and outer halfshaft ends.
3. Inspect the inner and outer halfshaft ends.

5.
Install Special Service Tool: 205-1047 Protector, Halfshaft Seal.

http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN... 1/21/2019
Page 3 of 5

Installation

1. NOTICE: Take extra care not to damage the seal.

NOTE: Make sure that a new component is installed.

Remove the halfshaft seal protector before completely installing the halfshaft.
Remove Special Service Tool: 205-1047 Protector, Halfshaft Seal.

http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN... 1/21/2019
Page 4 of 5

2. Install the wheel knuckle.


Refer to: Wheel Knuckle (204-01B Front Suspension - 4WD, Removal and Installation).

3. Fill the front differential.


Refer to: Differential Draining and Filling (205-03 Front Drive Axle/Differential, General Procedures).

Copyright © 2019 Ford Motor Company

http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN... 1/21/2019
Page 5 of 5

http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN... 1/21/2019

You might also like