» MDS
» EXT-TN-1066869
Ceiling multi sensor 360°
Datasheet
Subject to technical alteration
Issue date: 05/28/2021
» APPLICATION
Ceiling mounted multi sensor designed for measuring light and motion in room and office spaces and typically used in lighting applications to
optimize energy efficiency through lighting control. Low profile design with various output signals compatible to all BMS manufacturers. For
mounting on concrete ceilings an enclosure for surface mounting is available.
» TYPES AVAILABLE
Ceiling multi sensor light + motion – active 0..10 V (light), relay (motion)
MDS EXT-TN-1066869
» SECURITY ADVICE – CAUTION
The installation and assembly of the device should only be performed by authorized personnel.
The product should only be used for the intended application. Unauthorized modifications are prohibited! The product must not be
used in relation with any equipment that in case of a failure may threaten, directly or indirectly, human health or life or result in
danger to human beings, animals or assets. Ensure all power is disconnected before installing. Do not connect to live/operating
equipment.
Please comply with
• Local laws, health & safety regulations, technical standards and regulations
• Condition of the device at the time of installation, to ensure safe installation
• This data sheet and installation manual
» NOTES ON DISPOSAL
As a component of a large-scale fixed installation, BELIMO Aircontrols Inc. products are intended to be used permanently as part
of a building or a structure at a pre-defined and dedicated location, hence the Waste Electrical and Electronic Act (WEEE) is not
applicable. However, most of the products may contain valuable materials that should be recycled and not disposed of as domestic
waste. Please note the relevant regulations for local disposal.
BELIMO Aircontrols Inc.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
Page 2 / 4 Issue Date: 28.05.2021
» TECHNICAL DATA
Measuring values Brightness, motion
Output voltage Brightness
1x 0..10 V, min. Last 10 kΩ
Output switching contact Motion
floating contact (NO), max. 24 V | 1 A, with follow-up time 1 second..30 minutes, adjustable at the device
Power supply 15..24 V DC (±10%) or 24 V AC (±10%) SELV
Power consumption typ. 1,5 W (24 V DC) | 4 VA (24 V AC)
Measuring range light 0..93 fc (1000 Lux)
Accuracy light ±4,6 fc (±50 Lux)
Detection range Cone-shaped detection range, angle 105°, range > 16.4 ft., 444 detection zones. With an installation height
of 9 ft. circular detection range will have a D= 23 ft..
Sensor PIR (passive infrared)
Enclosure ABS, pure white
Protection NEMA 2x (IP20 according to EN 60529)
Connection electrical terminal, max. 16 AWG, plugable
Ambient condition +32..+122 °F (0..+50 °C), max. 85% rH non-condensing
Notes Enclosure for surface mounting available
» PRODUCT TESTING AND CERTIFICATION
Declaration of conformity
The declaration of conformity of the products can be found on our website https://www.belimo.us/en_US/.
BELIMO Aircontrols Inc.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
Issue Date: 28.05.2021 Page 3 / 4
» MOUNTING ADVICES
Mounting height
The mounting height has a direct influence on the range of the motion detector. The optimum mounting height is 9 ft. (2.70 m). All other
dimensions will change the range.
Fixed mounting
The motion detector must be mounted on a solid surface, as any movement of the detector will result in false alarms.
Distance to switched luminaires
In order to avoid unintentional switching on of the luminaire by the motion detector, the luminaire should not be mounted in the detection area of
the motion detector. Also avoid mounting the motion detector above a luminaire. The heat radiation of the luminaire can influence the function of
the motion detector and possibly lead to a false triggering of the detector.
Mounting sideways to the walking direction
For optimum motion detection, the detector must be mounted to the side of the detection area so that the zones are cut as vertically as possible.
Mounting locations where the objects to be detected move directly onto the motion detector result in a significant reduction of the range.
Distance to interference sources
To avoid false alarms, sources of interference such as radiators, lamps, air outlets from air conditioning systems, etc. should be outside the
detection range. Direct sunlight should also be avoided.
Feedback on detected movement
Motion detection by the sensor is signalled by the integrated signal LED (flashing for approx. 2 seconds). Note: The signalling LED is independent
of the set follow-up time of the relay output. During initialisation of the device (voltage reset), the signalling LED and the relay output are switched
on for approx. 45 seconds.
» DETECTION RANGE
This sensor detects changes in infrared radiation that occur when a person
(or object) moves whose temperature is different from the environment.
The mentioned ranges relate to average conditions upon a certain mounting
height. Thus, they should only be considered as approximate values. The
range can considerably deviate upon changing temperature conditions. The
necessary temperature difference between object for detection and the
background should be at least 5K. The speed of the object should at least
amount to 1 to 3.3 ft/s. The occupancy sensor should not be mounted near
interfering heat sources (e.g. lamps, radiators, fans etc.), to prevent faulse
triggering. The target concept should be a human body with an approx. size
of 28×10 in..
BELIMO Aircontrols Inc.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
Page 4 / 4 Issue Date: 28.05.2021
» CONNECTION PLAN
Relay switch-off delay adjustable via potentiometer in the range from 1s to 30 min.
» DIMENSIONS (IN.)
BELIMO Aircontrols Inc.
800-543-9038 USA 866-805-7089 CANADA 203-791-8396 LATIN AMERICA / CARIBBEAN
