TRI-MODE HEAT DETECTOR
MIX-4030 / MIX-4030-ISO
Features
• Any combination of MIX-4000 series devices up to 240
can be connected on a single SLC.
• Different LED colors for Alarms and Troubles
• Three operational modes of heat detection.
• Compatible with the full series of MIX-4000 input and
control modules.
• The device can be secured by a unique Anti- Tamper
feature.
• The address is set with the hand-held device programmer
(MIX-4090)
• MODEL OPTION - Built-in short-circuit isolator (MIX 4030-
ISO)
• Operating Modes
MIX-4030 / MIX-4030-ISO - Rate of rise heat detection (135ºF/57ºC)
- Fixed heat detection (135ºF/57ºC)
- Fixed heat detection (175ºF/79ºC)
Description Benefits
The MIX-4030/MIX-4030-ISO detector is a hardwired sensor • Open style mounting bases offer easy wiring and low
that continuously monitors the environmental temperature to pressure locking
report high heat conditions and communicates with the panel • 4" or 6" base options available
using a fully digital protocol.
• Remote output can be controlled by the panel
An alarm will be reported when the sampled temperature
exceeds 135ºF (57ºC) or 175ºF (79ºC) depending on the • MIX-4030-ISO is equipped with a bi-directional short-
chosen mode of operation. Excessive temperature rises circuit isolator to protect against wiring faults and loop
can also be reported if the detector is configured for rate- failure.
of-rise operation. • Low standby current.
The MIX-4030/MIX-4030-ISO works with an MGC compatible • Base has detachable tab for labeling device address.
control panel supporting high rates of information exchange
with reliable and secure bi- directional communication.
• Leverages interrupts to quickly report alarm conditions to
fire alarm control panels.
The detector is addressed and programmed using the
MIX-4090 hand-held device. Addresses can be selected from
• Magnet test option helps with commissioning and
maintenance.
a range of 1 -240.
This detector ships with a dust cover to protect the device
during installation and prior to commissioning.
Two tri-color LEDs on the device provide 360 degrees of
status visibility.
A remote LED indicator can be wired directly to the sensor.
CATALOG NUMBER
9503
NOT TO BE USED FOR INSTALLATION PURPOSES.
THIS INFORMATION IS FOR MARKETING PURPOSES ONLY AND
NOT INTENDED TO DESCRIBE THE PRODUCTS TECHNICALLY.
Technical Specifications
Normal Operating Voltage 15 to 30VDC
Maximum Alarm Current 3.2mA (LED on)
Standby Current 160μA
Temperature Range 32ºF to 100ºF (0ºC to 37.8ºC)
Humidity 10% to 93% Non-condensing
Wiring range on terminals 22 to 12 AWG
Diameter 4.25"
Height 1.75"
Detector LED colors Description Heat Detection Settings
RED (Steady on) ALARM condition 135ºF (57ºC)
GREEN (Flash) NORMAL condition 175ºF (79ºC)
AMBER (Steady on) FAULT condition 135ºF (57ºC) rate of rise
Ordering Information
Model Description
MIX-4010 Photoelectric Smoke Detector (Non-Isolated)
MIX-4010-ISO Photoelectric Smoke Detector (with short-circuit isolator)
MIX-4020 Multi-Criteria/Multi-Sensor (Non-Isolated)
MIX-4020-ISO Multi-Criteria/Multi-Sensor (with built-in short circuit isolator)
MIX-4030 Heat Detector (Non-Isolated)
MIX-4030-ISO Heat Detector (with built-in short circuit isolator)
MIX-4090 MIX-4000 Addressable Device Programmer
MIX-4001 6" Detector Base
MIX-4002 4" Detector Base
THIS INFORMATION IS FOR MARKETING PURPOSES
ONLY AND NOT INTENDED TO DESCRIBE THE
PRODUCTS TECHNICALLY.
Canada U.S.A.
25 Interchange Way 4575 Witmer Industrial Estates For complete and accurate technical information relating to
performance, installation, testing and certification, refer to technical
Vaughan, Ontario L4K 5W3 Niagara Falls, NY 14305
literature. This document contains intellectual property of Mircom.
Telephone: (905) 660-4655 Toll Free: (888) 660-4655 The information is subject to change by Mircom without notice.
Fax: (905) 660-4113 Fax Toll Free: (888) 660-4113 Mircom does not represent or warrant correctness or completeness.
www.mircom.com CAT. 9503
Rev. 3
