Maro

Maro Maro

Maro Maro

Air-Operated Double
Diaphragm Pumps
 MA-Series Pumps
Maro Non-Metallic & Metallic Models

Value Proposition

MARO Diaphragm Pumps: Keys to

MARO Air Motor Technology

1. “Unbalanced” Major Air Valve

 Unbalanced valve design eliminates

valve centering and pump stall-out,
even under low air inlet pressures.
 “O” Ring seals prevent waste of
expensive compressed air.
 Air flow stops when fluid flow stops.
 Maintenance is simple: just replace the
worn “O” Rings and “U” Cups.

2. Independent Pilot Rod

 Utilizes pneumatics and mechanical

action to shift Pilot Rod. Ensures
positive pilot signal, avoiding stall-out.

3. Broad Material Selection

 Options allow you to optimize

compatibility between the pump and
fluid being moved.
 Non-Metallic Diaphragm Pumps are
available in polypropylene, PVDF and
groundable acetal.
 Check models for availability.
 Metallic Diaphragm Pumps are available
in aluminum, stainless steel and cast
iron. Check models for availability.

4. Diaphragm/Ball Check Options

 Fit your pump with the diaphragms and

ball checks needed to maximize fluid
compatibility and abrasion

Introducing the New High-Flow Pumps: MA50 and MA75:

At the far end of the fluid delivery spectrum, the new MARO MA Series 2” and 3” port models feature
MARO’s patented “Unbalanced”, stall-free air valve design and bolted construction for leak-tight integrity.
With maximum delivery rates of 651 l/min (2”) and 897 l/min (3”), the new high-flow pumps are the ideal
answer to big volume applications - where performance with economy are a must.
 MA-Series Pumps
Maro Non-Metallic & Metallic Models

Materials

Optimum
Compound Main Applications / Chemical Compatibility
Temperature

10 to 54 °C General purpose diaphragm

Neoprene (non-aggressive applications ─ water-based slurries, well
50 to 130 °F water or sea water).

10 to 60 °C
Petroleum/oil-based fluids (leaded gasoline, fuel oils, non-synthetic
Buna-N
hydraulic oils, kerosene, turpentine, motor oils).
50 to 140 °F

10 to 60 °C
Extremely cold temperatures. Low cost alternative when pumping
EPDM
dilute acids or caustics.
50 to 140 °F

24 to 100 °C Extremely hot temperatures. Aggressive fluids such as aromatic or

Viton chlorinated hydrocarbons and highly aggressive acids in
75 to 212 °F applications involving suction lift outside the range of PTFE.

10 to 54 °C
Non-aggressive applications (water-based slurries, well water or sea
Polyurethane
water).
50 to 130 °F

10 to 100 °C
Low cost alternative to Teflon® in many acidic and caustic
Santoprene applications such as sodium hydroxide, sulfuric or hydrochloric, At a
50 to 212 °F cost comparable to neoprene.

10 to 54 °C ºC
FDA approved for food processing applications. Outstanding
Hytrel
general purpose diaphragm as well.
50 to 130 °F

10 to 100 °C
PTFE Aggressive chemicals and solvent but low abrasion resistance.
50 to 212 °F
 MA-Series Pumps
Maro ½” Non-Metallic Models

MA15 Non-Metallic Pump

½” Non-Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 49.2 l/min (13 gpm)
Maro
Air Inlet: ¼” BSP-Female
Fluid Inlet: ½” BSP-Female
Fluid Outlet: ½” BSP-Female
Max. working pressure: 6.9-bar (100 psi)
Suspended solids max. dia.: 2.4 mm (3/32”)

Weight: 4 kg (8.8 lbs)

Maximum dry suction lift: 3.05 m (10 ft)

Identification Code

MA 15 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

MA A: Aluminium S: Santoprene B: BSP

15: ½”
MEXP S: Stainless steel N: Nitrile N: NPT
25: 1"
C: Cast iron T: Teflon (PTFE) F: Flange
MWR 40: 1-½”
P: Polypropylene V: Viton
DP 50: 2" K: PVDF / PTFE
75: 3"
 MA-Series Pumps
Maro ½” Non-Metallic Models

Performance Curve
Meters

Bar

2 4 6 8 10 Air Consumption in Liter/Sec

Performance based on water

6.9 bar at ambient temperature
6 12
60
Total Discharge Head

4.8 bar

NPSH Required (m)

40 4 8
NPSHr

2.8 bar
20 2 4

0 0 0
0 10 20 30 40 50
Capacity (Liters/Min)

Dimensions (mm)
Fluid Outlet
164 mm ½” BSP (F)
207 mm
152 mm

Maro
Maro

288 mm
282 mm

Maro
255 mm

153 mm

51 mm

8 mm NOTE:
122 mm Air Inlet
156 mm ¼” BSP (F) Loosening
215 mm 140 mm these fasteners
Fluid Inlet will allow Inlet /
½” BSP (F) Outlet to rotate
 MA-Series Pumps
Maro 1” Non-Metallic Models

MA25 Non-Metallic Pump

1” Non-Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 170 l/min (45 gpm)
Air Inlet: ¼” BSP-Female
Fluid Inlet: 1” ANSI/DIN Flange
Fluid Outlet: 1” ANSI/DIN Flange
Max. working pressure: 8.3-bar (120 psi)
Suspended solids max. dia.: 3.2 mm (1/8”)
Maro

Weight: kg (lbs)
MA25-PX (Polypropylene) 9.5 (21)
MA25-KX (Kynar) 12.9 (28.4)

Maximum dry suction lift: 4.5 m (14.8 ft)

Identification Code

MA 25 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

MA 15: ½” A: Aluminium S: Santoprene B: BSP

MEXP 25: 1" S: Stainless steel N: Nitrile N: NPT
MWR 40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
DP 50: 2" P: Polypropylene V: Viton
75: 3" K: PVDF / PTFE
 MA-Series Pumps
Maro 1” Non-Metallic Models

Performance Curve
Meters

Bar

5 8 12 16 20 22 Air Consumption in Liter/Sec

100 10
Performance based on water
at ambient temperature

80 8
Total Discharge Head

8.3 bar
60 6 12
NPSHr
6.9 bar

NPSH Required (m)

4.8 bar
40 4 8

2.8 bar
20 2 4

0 0 0
0 40 80 120 160 200
Capacity (Liters/Min)

Dimensions (mm)

204 mm 322 mm
23 mm Oulet PCD 81 mm
406 mm

349 mm

Maro
Maro

Inlet
60 mm
13 mm 11 mm
128 mm
160 mm
Air Inlet
1” ANSI/DIN ¼” BSP (F)
Flange
 MA-Series Pumps
Maro 1-½” Non-Metallic Models

MA40 Non-Metallic Pump

1-½” Non-Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 378 l/min (100 gpm)
Air Inlet: ½” BSP-Female
Fluid Inlet: 1-½” ANSI/DIN Flange
Fluid Outlet: 1-½” ANSI/DIN Flange
Max. working pressure: 8.3-bar (120 psi)
Maro
Suspended solids max. dia.: 6.4 mm (¼”)

Weight: kg (lbs)
MA40-PX (Polypropylene) 28.1 (62)
MA40-KX (Kynar) 41.7 (92)

Maximum dry suction lift: 4.27 m (14 ft)

Identification Code

MA 40 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

15: ½” A: Aluminium S: Santoprene B: BSP

MA
25: 1" S: Stainless steel N: Nitrile N: NPT
MEXP
40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
MWR
50: 2" P: Polypropylene V: Viton
DP
75: 3" K: PVDF / PTFE
 MA-Series Pumps
Maro 1-½” Non-Metallic Models

Performance Curve
Meters

Bar

15 30 40 50 70 Air Consumption in Liter/Sec

100 10
Performance based on water
at ambient temperature

80 8
8.3 bar
Total Discharge Head

6.9 bar
60 6 12
NPSHr

NPSH Required (m)

4.8 bar
40 4 8

2.8 bar
20 2 4

0 0 0
0 100 200 300 400 500
Capacity (Liters/Min)

Dimensions (mm)
Fluid Oulet
297 mm 1-½” ANSI/DIN Flange
294 mm 501 mm
PCD 98.5 mm
625 mm

Maro Air Inlet

545 mm

Maro
½” BSP (F)
83 mm

244 mm

26 mm 220 mm 16 mm 86 mm

255 mm 379 mm
Air Exhaust Thread ¾” BSP (F) Fluid Inlet
1-½” ANSI/DIN Flange
 MA-Series Pumps
Maro 2” Non-Metallic Models

MA50 Non-Metallic Pump

2” Non-Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 548 l/min (145 gpm)
Air Inlet: ½” BSP-Female
Fluid Inlet: 2” ANSI/DIN Flange
Fluid Outlet: 2” ANSI/DIN Flange
Max. working pressure: 8.3-bar (120 psi)
Maro
Suspended solids max. dia.: 6.4 mm (¼”)

Weight: kg (lbs)
MA50-PX (Polypropylene) 28.1 (62)
MA50-KX (Kynar) 41.7 (92)

Maximum dry suction lift: 4.27 m (14 ft)

Identification Code

MA 50 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

MA 15: ½” A: Aluminium S: Santoprene B: BSP

MEXP 25: 1" S: Stainless steel N: Nitrile N: NPT
40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
MWR
50: 2" P: Polypropylene V: Viton
DP
75: 3” K: PVDF / PTFE
 MA-Series Pumps
Maro 2” Non-Metallic Models

Performance Curve
Meters

Bar

20 30 40 50 60 70 Air Consumption in Liter/Sec

10
100 Performance based on water
at ambient temperature

8
80 8.3 bar
Total Discharge Head

6.9 bar
60 6 12
NPSHr

NPSH Required (m)

4.8 bar
40 4 8

2.8 bar
20 2 4

0 0 0
0 120 240 360 480 600
Capacity (Liters/Min)

Dimensions (mm)
Fluid Oulet
297 mm 2” ANSI/DIN Flange
294 mm 501 mm
PCD 121 mm
625 mm

Maro Air Inlet

545 mm

Maro
½” BSP (F)
83 mm

244 mm

26 mm 220 mm 16 mm 86 mm

255 mm 379 mm
Air Exhaust Thread ¾” (BSP) Fluid Inlet
2” ANSI/DIN Flange
 MA-Series Pumps
Maro ½” Metallic Models

MA15 Metallic Pump

½” Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 45 l/min (12 gpm)
Air Inlet: ¼” BSP-Female
Fluid Inlet: ½” BSP-Female
Fluid Outlet: ½” BSP-Female
Max. working pressure: 6.9-bar (100 psi)
Suspended solids max. dia.: 3.3 mm (1/8” inch)

Maro
Weight: kg (lbs)
MA15-AX (aluminum) 4.7 (10.4)
MA15-SX (stainless steel) 7.5 (16.6)

Maximum dry suction lift: 3.3 m (10.8 ft)

Identification Code

MA 15 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

15: ½” A: Aluminium S: Santoprene B: BSP

MA
25: 1" S: Stainless steel N: Nitrile N: NPT
MEXP
40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
MWR
50: 2" P: Polypropylene V: Viton
DP
75: 3” K: PVDF / PTFE
 MA-Series Pumps
Maro ½” Metallic Models

Performance Curve
Meters

Bar

4 6 8 10 Air Consumption in Liter/Sec

80 8
Performance based on water
at ambient temperature 20
6.9 bar
6
60
16
Total Discharge Head

NPSH Required (m)

4.8 bar
NPSHr
12
40 4

8
2.8 bar
20 2
1 lit/sec
4
2 lit/sec

0 0 0
0 10 20 30 40 50
Capacity (Liters/Min)

Dimensions (mm)
Air Inlet
¼” BSP (F)
205.5 mm
208.5 mm 152.4 mm
109.3 mm 31.8 mm

Oulet
1” BSP (F)

Maro
280.4 mm

297.9 mm

Maro
50.8 mm
159.9 mm

Inlet
1” BSP (F)

8 mm 77.8 mm 9.5 mm 123.8 mm

155.6 mm 139.7 mm
 MA-Series Pumps
Maro 1” Metallic Models

MA25 Metallic Pump

1” Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 133 l/min (35 gpm)
Air Inlet: ¼” BSP-Female
Fluid Inlet: 1” BSP-Female
Fluid Outlet: 1” BSP-Female
Max. working pressure: 8.3-bar (120 psi)
Suspended solids max. dia.: 3.2 mm (¼” inch)

Weight: kg (lbs)
Maro MA25-AX (aluminum) 8.6 (19)
MA25-SX (stainless steel) 16.3 (36)

Maximum dry suction lift: 4.5 (14.8 ft)

Identification Code

MA 25 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

MA 15: ½” A: Aluminium S: Santoprene B: BSP

MEXP 25: 1" S: Stainless steel N: Nitrile N: NPT
MWR 40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
DP 50: 2" P: Polypropylene V: Viton
75: 3” K: PVDF / PTFE
 MA-Series Pumps
Maro 1” Metallic Models

Performance Curve
Meters

Bar

5 8 12 16 20 22 Air Consumption in Liter/Sec

10
100 Performance based on water
at ambient temperature
8.3 bar
8
80
Total Discharge Head

6.9 bar
60 6 12
NPSHr

NPSH Required (m)

4.8 bar
40 4 8

2.8 bar
20 2 4

0 0 0
0 40 80 120 160 200
Capacity (Liters/Min)

Dimensions (mm)

217 mm Fluid Oulet 203 mm

1” BSP (F)

Air Inlet
¼” BSP (F)
318 mm

Maro
294 mm

Maro
165 mm

32 mm 102 mm Fluid Intlet 159 mm

1” BSP (F)
11 mm
186 mm
 MA-Series Pumps
Maro 1-½” Metallic Models

MA40 Metallic Pump

1-½” Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 340 l/min (90 gpm)
Air Inlet: ½” BSP-Female
Fluid Inlet: 1-½” BSP-Female
Fluid Outlet: 1-½” BSP-Female
Max. working pressure: 8.3-bar (120 psi)
Suspended solids max. dia.: 6.4 mm (¼” inch)

Maro
Weight: kg (lbs)
MA40-AX (aluminum) 23.4 (51.5)
MA40-SX (stainless steel) 38.3 (84.5)
MA40-CX (cast iron) 36.1 (79.5)

Maximum dry suction lift: 5.4 m (17.6 ft)

Identification Code

MA 40 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

MA 15: ½” A: Aluminium S: Santoprene B: BSP

MEXP 25: 1" S: Stainless steel N: Nitrile N: NPT
MWR 40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
DP 50: 2" P: Polypropylene V: Viton
75: 3” K: PVDF / PTFE
 MA-Series Pumps
Maro 1-½” Metallic Models

Performance Curve
Meters

Bar

15 30 40 50 70 Air Consumption in Liter/Sec

10
100 Performance based on water
at ambient temperature

8
80 8.3 bar
Total Discharge Head

6.9 bar
NPSHr
60 6 12

4.8 bar

NPSH Required (m)

40 4 8
2.8 bar

20 2 4

0 0 0
0 80 160 240 320 400
Capacity (Liters/Min)

Dimensions (mm)
Fluid Oulet
1-½” BSP (F)
376 mm
333 mm 292 mm
Maro
498 mm

Air Inlet
467 mm

½” BSP (F)
Maro
70 mm
194 mm

Air Muffler Thread

¾” BSP (F)

298 mm 14 mm
324 mm 229 mm
Fluid Intlet
1-½” BSP (F)
 MA-Series Pumps
Maro 2” Metallic Models

MA50 Metallic Pump

2” Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 650 l/min (172 gpm)
Air Inlet: ¾” BSP-Female
Fluid Inlet: 2” BSP-Female
Fluid Outlet: 2” BSP-Female
Max. working pressure: 8.3-bar (120 psi)
Suspended solids max. dia.: 6.4 mm (¼” inch)

Maro Weight: kg (lbs)

MA50-AX (aluminum) 29.6 (65.2)
MA50-SX (stainless steel) 58.9 (130)
MA50-CX (cast iron) 56.5 (124.3)

Maximum dry suction lift: 5.8 m (19 ft)

Identification Code

MA 50 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

15: ½” A: Aluminium S: Santoprene B: BSP

MA
25: 1" S: Stainless steel N: Nitrile N: NPT
MEXP
40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
MWR
50: 2" P: Polypropylene V: Viton
DP
75: 3” K: PVDF / PTFE
 MA-Series Pumps
Maro 2” Metallic Models

Performance Curve
Meters

Bar

10 25 40 50 70 Air Consumption in Liter/Sec

100 10
Performance based on water
at ambient temperature

80 8
8.3 bar
Total Discharge Head

6.9 bar
60 6 12
NPSHr

NPSH Required (m)

4.8 bar
40 4 8

2.8 bar

20 2 4

0 0 0
0 100 200 300 400 500 600 700 800
Capacity (Liters/Min)

Dimensions (mm)

577.3 mm
455 mm 330.2 mm
227.6 mm 50.8 mm

Fluid Oulet
2” BSP (F)
Maro
628.7 mm

670 mm

Air Inlet
¾” BSP (F)
Maro
215 mm

Air Muffler Thread

1-¼” BSP (F) 133.4 mm

14.3 mm 47.6 mm 230.2 mm

255.6 mm Fluid Intlet 255.6 mm
2” BSP (F)
 MA-Series Pumps
Maro 3” Metallic Models

MA75 Metallic Pump

3” Metallic Performance Specifications

Ratio: 1:1
Maximum Capacity: 897 l/min (237 gpm)
Air Inlet: ¾” BSP-Female
Fluid Inlet: 3” BSP-Female
Fluid Outlet: 3” BSP-Female
Max. working pressure: 8.3-bar (120 psi)
Suspended solids max. dia.: 9.5 mm (3/8” inch)

Maro Weight: kg (lbs)

MA75-AX (aluminum) 49.8 (109.8)
MA75-SX (stainless steel) 101 (222)
MA75-CX (cast iron) 96.7 (213)

Maximum dry suction lift: 5.8 m (19 ft)

Identification Code

MA 75 - X X - X

Series Pump Hardware Elastomer Connection

Type Size Material Material Standard

15: ½” A: Aluminium S: Santoprene B: BSP

MA
25: 1" S: Stainless steel N: Nitrile N: NPT
MEXP
40: 1-½” C: Cast iron T: Teflon (PTFE) F: Flange
MWR
50: 2" P: Polypropylene V: Viton
DP
75: 3” K: PVDF / PTFE H: Hytrel
 MA-Series Pumps
Maro 3” Metallic Models

Performance Curve
Meters

Bar

10 25 40 50 70 90 Air Consumption in Liter/Sec

100 10
Performance based on water
at ambient temperature

80 8
8.3 bar
Total Discharge Head

6.9 bar
60 6 12
NPSHr

NPSH Required (m)

4.8 bar
40 4 8

2.8 bar

20 2 4

0 0 0
0 200 400 600 800 1000
Capacity (Liters/Min)

Dimensions (mm)

620.7 mm
564 mm 406.4 mm
282 mm 70 mm

Fluid Oulet
3” BSP (F)
762 mm

Maro
820 mm

Air Inlet
¾” BSP (F)

Maro
282 mm

Air Muffler Thread 133.4 mm

1-¼” BSP (F)

14.3 mm 60.3 mm 258 mm

306.4 mm Fluid Intlet 279.4 mm
3” BSP (F)
Maro Replacement Parts
MARO are always on hand to provide replacement diaphragm
parts. We are convering a wide range of different pump brand
parts. In additional, we committed to supply Quality products
with Competitve Pricing. Rup
p® | After-Market Parts
- Replacement Parts that fit Wilden® | After-Market Parts
- Replacement Parts that fit ARO® | After-Market Parts
- Replacement Parts that fit Warren Rupp® | After-Market Parts
- And many others brands.

MARO reserves the right to alter specifications

at any time without prior notice. Distributed by:

Maro
Printed 2018/05