*Note: All pictures herein are only for reference purpose and this Quick Start Guide is subject
to change
Quick Start Guide without written notice.
Product Profile Preparation & Connection
DB15 Connector 1. Preparation
( Connects the diagnostic cable. )
*Note:The buttons marked with * 1) Switch the ignition on.
indicate the function hot keys.
2) The vehicle battery voltage should be 11-14V or 18V-30V.
3) Throttle should be in a closed position.
2.Locate vehicle’s DLC
Display Screen Data I/O Port The DLC(Data Link Connector) is typically a connector where diagnostic code readers interface
( Indicates the test results. ) ( Connects to PC for update via data cable. ) with the vehicle’s on-board computer. For heavy-duty vehicles, it is generally located in driver’s
cab. If the DLC cannot be found, refer to the vehicle’s Repair Manual for the exact location.
DTC LED NO DTC LED 3.Connection
( Illuminates RED when DTCs ( Illuminates GREEN if no DTCs Select the desired diagnostic connector according to the vehicle DLC type and then follow the
are found.) are found.) steps below to proceed:
SCAN Button* BACK Button 1.For vehicles equipped with an OBD II management system, plug one end of the diagnostic
cable into the vehicle’s DLC, and the other end into the DB15 connector of the tool and tighten
( Quick access to Auto Scan. ) ( Returns to the previous screen. ) the captive screws.
DTC Retrieval Button* 2.For vehicles not equipped with an OBD II management system, do the following:
Battery Voltage Button*
1). Select the corresponding non-16pin adaptor cable.
( Quick access to DTC Lookup. ) ( Quick access to check battery voltage. ) 2). Plug the non-16pin end of the adaptor cable into the DLC socket, and the other end to the
diagnostic cable.
Selection Buttons
3). Plug the other end of the diagnostic cable into the DB15 connector of the tool and tighten
the captive screws.
OK Button
( Confirms an selection or action from a Start Diagnostics
menu list.)
CR-HD PRO features two kinds of diagnostic approaches: Auto scan and Manual diagnosis.
Accessory Checklist
1.Manual Diagnosis 2.Auto Scan
In this mode, you have to diagnose a vehicle by This function allows you to scan the HD-
performing the menu-driven command manually. OBD or EOBD II.
For new users, please follow the operation chart
shown below to get familiar with and start using
this tool. Statement: LAUNCH owns the complete
OBD-6 Adaptor Cable OBD-9 Adaptor Cable intellectual property rights for the software
Follow on-screen used by this product. For any reverse
Standard 6-pin Deutsch 9-pin Deutsch adaptor Select "Manual Scan"
Diagnostic Cable Data Cable prompts to proceed
adaptor for most heavy- for use with vehicles engineering or cracking actions against the
To connect the CR-HD duty vehicles. Covers covering 1998 to present Connects the CR-HD software, LAUNCH will block the use of this
PRO to vehicle’s OBD2 1995 to present Class 4- Class 4-8 heavy-duty PRO to PC to make Select software product and reserve the right to pursue their
diagnostic socket. 8 heavy-duty OEM. OEM. update. Select vehicle
version legal liabilities.
EN
3. Function Modules 4. Update
The tool can be updated via data cable.
Main Function Diagnose: Configures this tool to operate as a *Note: Make sure the PC has an Internet connection.
diagnostic tool.
1. Go to http: // mycar.x431.com / and download the update tool to the computer.
Battery: Reads the vehicle’ battery voltage.
Lookup: Retrieves the desired Diagnostic 2. Decompress and install it on your computer(compatible with Windows XP, Windows 7, Windows
Diagnose Battery Lookup 8 & Windows 10).
Trouble Code (DTC) from the DTC library.
Help: Lets you have a general knowledge of the 3. After installation, connect one end of the data cable to the USB port of PC, and the other end to
OBD II, HD OBD and I/M Readiness. the tool.
Help Setup Info Setup: Makes the system setting of the tool. *Note: If the tool is properly connected to the PC, the NO DTC LED illuminates green, and the DTC LED
Info: Includes the tool information, including goes out. Otherwise, the red LED illuminates and the green LED lights off.
software & hardware version, and Serial Number 4. Launch the update tool on your PC, the system starts reading the tool. Once it obtains the tool
The icons in black at the bottom of the
etc. information, it will directly navigate to the update center.
screen indicate the available actions,
which can be done by pressing the
corresponding buttons on the tool.
Read DTC: Displays the detailed information of
Main Diagnostic Features
DTC records retrieved from the vehicle’s control
system.
Engine
Clear DTC: After reading the DTCs from the
Read DTC vehicle and certain repairs have been made, use
this function to erase the codes from the vehicle.
Clear DTC
Before performing this function, please be sure the
Data Stream vehicle’s ignition key is in the ON position with the
engine off.
Data Stream: Lets you view and capture 5. Click [Start Upgrade] to start updating.
(record) real-time Live Data. It can also be used
6. Once update is complete, a “Upgrade success” message box will pop up and the tool will jump
OK to guide vehicle repair.
to the main function screen.
7. The update process is complete, your tool is now ready for use.
*Note: To enjoy more capabilities and functions, you are suggested to check for updates on a frequent basis
Battery Voltage DTC Lookup and keep synchronized with the latest available software.
Reads the battery voltage to check Provides access to libraries of OBD and
the status of the battery. OBD II DTC definitions.
*Note: This function can be accessed *Note: This function can be accessed LAUNCH www.x431.com
www.cnlaunch.com
directly by pressing the - + button on directly by pressing the DTC button on the
the tool. tool.
Battery Lookup Thanks for choosing LAUNCH!
Please input DTC: If you have any questions or comments on the operation of the unit, please contact
P0000 LAUNCH Customer Service Center:
The 1st range: P, C, B, U Phone: +86 755 8455 7891
The 2nd range: 0, 1, 2, 3
The others from 0 to F Email: [email protected]
Press [ ] or [ ] to change input, press [ ] or
[ ] to select position, then press [OK] to confirm.
*WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the
12.0V ENG: ON OK following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
