Enhanced Willem EPROM Programmer

Quick Start Guide

V1.0

1. Installation

1.1 Turn off the PC

1.2 Connect the DB25 parallel cable Male connector to PC’s printer port
1.3 Connect the DB25 parallel cable Female connect to Willem EPROM Programmer
1.4 Plug in the USB cable to the PC USB port
1.5 Connect the USB Cable to the Enhanced Willem EPROM Programmer – the Green LED should light up

1.6 Turn on the PC

1.7 Download the parallel port IO driver from -- www.driverlinx.com/ftp/unsupported/port95nt.exe
1.8 Install the drivers then restart your PC, run the utility and playaround with it a bit to get the DLL and
SYS file installed in the system and start a service.
1.9 Copy the programmer software 97g.zip from Floppy Disk into the Hard Disk
1.10 Unzip the file 97g.zip, all unzipped files should put in the same directory/folder
1.11 Double click the EpromM51 icon to start the program, then check the programmer type,
change it to PCB3 if it shows Willem.

1.10 Select Help from the main, then click Test Hardware. It should shows
Hardware Present in the status bar, otherwise please Check Power & connection
2. Jumper Setting & Socket Layout

Protection Jumper - Short to disable VPP & EPROM Select Vpp Select

EPROM Select
Programmer Reset

40 Pin for P28F00x

18 Pin for PIC

8 pin for 93cxx

8 Pin for 24cxx

a. Protection Jumper – Short to disable VPP & EPROM Select

b. Programmer Reset Button – Press to reset the programmer
c. Vpp Select Button – Press to Select “Normal, 15V, 21V, 25V”
d. EPROM Select Button – Press to Select “Normal, 2732, 2716, 2816, i28F, AT29, W27C”
 2.3 Group 3 – Only for 4M or 8M memory chip

Once completed the Jumper setting, please follow the program instruction/hence to config the DIP switch setting
before programming any chip

2. Devices supported

27C64, 27C128, 27C256, 27C512, 27C010, 27C020, 27C040,27C1001

M27C1001, M27C2001, M27C4001
27C080 (A19) ,M27C801,M87C257
EPROM
2716(Vpp25V),2732, (adapter DIP24)
2764, 27128, 27256, 27512, 27010,
Vpp12.5V (21Vpp Modify Circuit)

28C65,28C64, 28C128, 28C256,28C512, 28C010, 28C020, 28C040

EEPROM M28C16A/17A (DIP28)
(Adapter or Jumper) 28C16,XLS2816 (DIP24)

28F64, 28F128, 28F256, 28F512,28F010, 28F020

MX26C1000, MX26C2000, MX28F1000, MX28F2000
FLASH Memory Am28F256A, Am28F512A, Am28F010A, Am28F020A (New command erase/prog.)
-- intel ---
i28F001BX, 28F004, 28F008, 28F016

29F64, 29F128, 29F256, 29F512,29F010, 29F020, 29F040, 29F080

FLASH Memory
29F001,29F002, 29F004, 29F008, 29F016, 29F032

24C02,24C04,24C08,24C16, 85C72, 85C82, 85C92

Serial (I2C) EEPROM
--- page write ----
24Cxx
24C32,24C64,24C128,24C256,24C512

<------ Data 8bit -----> (pin 6 ->ORG. [Schematic connect to GND])

Microwire EEPROM 93C06, 93C46, 93LC46, 93C56, 93C57,
93C66, 93C76, 93C86 (8bit), AT59C11, AT59C22, AT59C13
 CAT35C102, CAT35C104, CAT35C108 (pullup pin7)
<------Data 16bit------> (pin 6 ->NC [No Connect])
93C06A ,93C46X,93C56,93C66,93C76,93C86 (NS)

16C84, 16F84, 16F84A ,16F627/16F628

12C508/A, 12C509/A, 12CE518, 12CE519, 16C505
16C620 16C621, 16C622, 16CE623, 16CE624, 16CE625, 16C710/711
MicroChip PIC
---ICSP connector----
16F870, 16F871, 16F872, 16F873, 16F874, 16F876, 16F877
PIC16F873A, PIC16F874A, PIC16F876A, PIC16F877A

AT29C256, AT29C512,AT29C010A, AT29C020, AT29C040,AT29C040A

W29EE512,W29EE011, W29EE012, W29C020(128),W29C040
Atmel Flash Memory PH29EE010(W29EE011)
(Sector Programming)
(Software Data Protection) ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020)
Ver 0.992 up(DOS). Can run under win9x
(disable prog. CPUIdle or CPUCool)

Command seq. 5555/AA, 2AAA/55, 5555/A0

AT49F512, AT49F010, AT49F020, AT49F040
Atmel Flash Memory SST39SF010, SST3S9F020 ,SST39SF040
AT49Fxxx (Subset 29Fxxx) AT49F001,AT49F002 , AT49F008A
(Byte-by-Byte Programming)
(Software Data Protection) Command seq. 555/AA, 2AA/55, 555/A0
Am29F512, Am29F010, Am29F020, Am29F040,HY29F080
29F002, 29F002T, Pm29F002T

[Atmel] AT25010,020, 040 (A8-A0)

AT25080, 160, 320, 640, 128, 256 (A15-A0)
[ST] W95010....256, Microchip 25x010 - 25x640

--- Byte programming

Serial Peripheral Interface (SPI) 25010,25020,25040
EEPROM Mode0 (0,0) --- Page programming
AT25xxx, W95xxx 25C080,25C160,25C320,25C640,25C128,25C256,25C512
AT25HP256,AT25HP512
AT25HP1024 (24bit address)

-- CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx

CAT64LC010, CAT64LC020, CAT64LC040

Atmel EEPROM (page prog.)

AT28C256, AT28C010, AT28C040
(Software Data Protection)

Nonvaltile SRAM (DS12xx) DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB

static RAM (Test RAM) 6116, 6264, 62256, 62512, 628128

W27E512, W27E010, W27C010, W27C020, W27C040

EPROM winbond,SST
SST27SF256, SST27SF512, SST27SF010, SST27SF020
Electrical Erase Chip
MX26C4000
 Vcc = 3.3-3.6V SST37VF512, SST37VF010, SST37VF020, SST37VF040

Flash Memory SST,Sanyo SST28SF040A ,LE28F4001

Adapters

Atmel Auto Setect

AT89C51,52,55, AT89LV51,52,55
AT89S8252 (8K+2K), AT89S53, AT89LS8252,AT89LS53
AT89C1051,AT89C2051,AT89C4051 (20pin)
Atmel AT89Cxx (MCS-51) AT89C51RC (32KB), AT89C55WD (6.2V)
Adapter 32pin to MCS-51 SST89C54/58 (not fully support), SI89C52
Intel Auto Select
i87C51, i87C51FA, i87C51FB
------------------------------------------------
i8xC51,i8xC52,i8xC54,i8xC58 (tWP = 100uS*25 Pulse)

(read,write,erase,verify,checkempty,Lockbits ,Fusebits) [Flash

memory/EEPROM]
Atmel AVR 8-bit RISC AT90Sxxx
AT90S1200,AT90S2313
(Parallel programming)
90S2333, 90S4433, 90S4414, 90S8515, 90S4434, 90S8535
Adapter 32pin to MCS-51
reference AT90S2313 pin
Function Lockbit read AT90S2313 Errata Sheet.pdf

ROM (read/verify)
P8048AH, P8049AH,P8050AH, P8042AH Vea = 12V
P8041, P8042

MCS-48,MCS-41
OTP (read/verify/Progam)
Adapter 32pin to MCS-48/41
P8748,P8749H,P8742H Vea = 18V

EPROM (read/verify/Progam)
D8748,D8749,D8742,D8741, D8742 Vea = 18V

FLASH memory 8/16bit

Am29F400,Am29F800,29F160,29F320 (read,write byte mode)
(Software Data Protection)
HY29F200, HY29F400, HY29F800 , AT49F2048A, AT49F4096A, AT49F8192A
</FONTAdapter (TSOP48)

FLASH memory 8/16bit (Vpp12V)

i28F200,i28F400,i28F800,i28F160 (TSOP48)
(Software Data Protection)
28F001(DIP32 or PLCC32)
</BAdapter (TSOP48)

27C1024 (27C210), 27C2048 (27C2002), 27C4096 (27C4002),

EPROM 16bit (DIP40) (1-4Mbit)
Schematic by Toomas Toots
Adapter Eprom 16bit
(read,Program byte mode
Eprom only
by use Resister pull up Data Bus (0xFF), A0 select low or high byte)

EPROM 16bit (DIP42) (4-32Mbit) M27C400(DIP40), 27C800, 27C160, 27C322

Adapter Eprom DIP42 Schematic by Toomas Toots
Eprom only (read,Program byte mode
 by use Resister pull up Data Bus (0xFF), A0 select low or high byte)

FLASH memory 8/16bit

(Software Data Protection) 29LV200, 29LV400,29LV800,29LV160,29LV320 (read,write byte mode)
Adapter (TSOP48LV)

-- Firmware Hub
82802AB, 82802AC, AT49LW040, AT49LW080

Firmware Hub / LPC FLASH SST49LF002A, SST49LF003A, SST49LF004A, SST49LF008A

Adapter Firmware Hub/LPC (PLCC32) W49V002FA, W39V040FA
(PP mode) (3.3V)
-- LPC flash
SST49LF020, SST49LF040
W49V002A, W39V040A

P28F002BC BOOT BLOCK FLASH MEMORY

Adapter P28F002BC (DIP40) - P28F002BC
3. Common used Flash Memory chip for PC Motherboard

VPP programming
IC Manufacture Part No. Memory Size
voltage

Am29F010 1M

Am29F002 2M

Am29F040 4M
AMD
Am28F010（A） 1M VPP=12.0 V

Am28F020（A） 2M VPP=12.0 V

Am28F040 4M VPP=12.0 V

AE29F010A 1M

AE29F020 2M

ASD AE29F040 4M

AE29F1008 1M

AE29F2008 2M

AT29C010A 1M

AT29C020 2M

AT29C040 4M
Atmel
AT49F001 1M

AT49F002 2M

AT49F004 4M

CAT28F001BX-T/B 1M VPP=12.0 V

CATALYST CAT28F010 1M VPP=12.0 V

CAT28F020 2M VPP=12.0 V

i28F001BX-T/B 1M VPP=12.0 V

Intel i28F010 1M VPP=12.0 V

i28F020 2M VPP=12.0 V

MX28F1000P 1M VPP=12.0 V

MX28F2000P/T 2M VPP=12.0 V
Macronix
MX29F001(N)T/B 1M

MX29F002(N)T/B 2M

F／V29C51001T/B 1M
Mosel-Vitelic
F／V29C51002T/B 2M

SST PH29EE010 1M

PH29EE020 2M

PH28SF040 4M
 PH39SF010 1M

PH39SF020 2M

M28F256(A) 256K VPP=12.0 V

M28F512 512K VPP=12.0 V

SGS－THOMSON
M28F001 1M VPP=12.0 V

M29F002T／NT／B 2M

W29EE011 1M

W29C010 1M
Winbond
W29C020 2M

W29C040 4M

End