AVOCENT® UNIVERSAL

MANAGEMENT GATEWAY APPLIANCE

Quick Installation Guide

Avocent® Universal Management Gateway 6000 Appliance Rear

3
5

8 2 8

The Avocent® Universal 1. Rack mounting

Management Gateway appliance the appliance
provides extensive access to For detailed rack and/or wall
attached devices. Care must be mounting instructions, see the Standard Autosensing
taken to avoid compromising your Avocent® Universal Port Port
security policies. Management Gateway
The appliance ships with the Appliance Mounting Bracket 4. Using autosensing ports
following default settings: Quick Installation Guide. The appliance has autosensing
• DHCP, SSH v2 and HTTPS are 2. Connecting ports used to connect serial,
enabled. to your network power, service processor and
• All autosensing ports are Connect a UTP cable from the KVM targets (depending on the
enabled. primary network port to your model). Autosensing ports are
• Ethernet and CLI Setup ports network. For redundancy, indicated by a turquoise line.
are enabled. connect both network ports. 5. Connecting targets
The following accounts exist by 3. Connecting Using UTP cables and
default: external sensors supported DB9 or DB25
• admin The appliance supports console adaptors, connect
environmental sensors targets to the appliance. For
• operator KVM targets, connect using an
connected to ports labeled TH,
• user DI, COM or SNSR. DO ports are UMIQ module. See the UMIQ
Shell access for admin is enabled. physical relays that can be used Module Quick Installation Guide
The first time you access the to turn on/off a DC powered for more instructions.
appliance, you must log in as admin device. For a list of the sensors WARNING: Connected serial
and create and confirm a password and configuration requirements, devices should not exceed 13
for the admin account. see the Avocent® Universal volts.
Management Gateway
Appliance Installer/User Guide.

590-1480-631D 1
AVOCENT® UNIVERSAL MANAGEMENT GATEWAY APPLIANCE
Quick Installation Guide

Avocent® Universal Management Gateway 6000 Appliance Front

6 7

NOTE: A patch panel is not 8. Turning on the appliance c. Click the eth0 entry in the
recommended as a connection For redundancy, the appliance table and use the drop-down
point between the appliance has dual power supplies. Plug menu to change the method
and an IQ module because it the power cables into the to Static.
can cause distance, power or
appliance and then into a power d. Assign the desired IP values
video quality control feature
issues. If the issues are still source to turn the appliance on. and click Apply.
present when the patch panel Then turn on the devices NOTE: For instructions on
is removed, contact Technical connected to the appliance. assigning an IP address using
Support. 9. Assigning an IP address the command line interface, see
An IP address can be obtained the Avocent® Universal
6. Connecting locally or Management Gateway
through the console port via DHCP or a static IP can be
assigned using the VGA or CLI Appliance Command Reference
You can configure and Guide.
Setup port.
manage the appliance either via
the VGA console or the CLI NOTE: If using DHCP, you must
Setup port. Use the provided first find the IP address
RJ45 to DB9 cross converter to assigned to the appliance by
connect a terminal or looking at the DHCP leases on
workstation to the CLI Setup the network DHCP server. Then
port. Terminal setting use a browser at
requirements are: 9600, 8, N https://<appliance IP> to
and 1, with no flow control and connect to the appliance.
ANSI emulation. If you are assigning an IP
7. Connecting USB devices address using VGA, perform the
You can use the USB ports on following steps:
the front of the appliance to a. Log in to the appliance’s web
connect a keyboard, video and user interface as admin.
mouse or other supported USB
b. Under the Administration tab,
devices.
click Network Settings.

To contact Vertiv Technical Support: visit www.Vertiv.com

© 2019 Vertiv Group Corp. All rights reserved. Vertiv and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. All other names and logos referred to are trade
names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Group Corp. assumes
no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

2 590-1480-631D
AVOCENT® UNIVERSAL MANAGEMENT
GATEWAY 装置
快速安装指南

Avocent® Universal Management Gateway 6000 装置背面

3
5

8 2 8

对于已连接的设备，Avocent® 1. 在机架上安装本装置
Universal Management Gateway 装 有关详细的机架和/或墙上安装
置提供多种访问方式。请务必格外 说明，请参阅《Avocent®
小心，以免破坏安全策略。 Universal Management 标准端口 自动检测端口
此装置的出厂默认设置为： Gateway 装置安装支架快速安
• 启用 DHCP、SSH v2 和 装指南》。
HTTPS。 2. 连接到网络 4. 使用自动检测端口
• 启用所有自动检测端口。 使用 UTP 缆线将主要网络端口 本装置配有用于连接串行、电源、
连接到您的网络。同时连接两个 服务处理器和 KVM 目标设备的自
• 启用以太网和 CLI 设置端口。
网络端口可提供冗余。 动检测端口（视型号而定）。自动
默认存在以下帐户： 检测端口标有青绿线。
3. 连接外部传感器
• admin 5. 连接目标设备
此装置支持与标有 TH、DI、COM
• operator 或 SNSR 的端口相连的环境传感 使用 UTP 缆线和支持的 DB9 或
• user 器。DO 端口是可用于打开/关闭 DB25 控制台适配器，将目标设备
admin（管理员）可进行 Shell 访问。 直流供电设备的物理继电器。 连接到装置。对于 KVM 目标设
有关传感器和配置要求列表， 备，可使用 UMIQ 模块连接。有关
第一次访问装置时，用户必须以
请参阅《Avocent® Universal 更多说明，请参阅《UMIQ 模块快
admin（管理员）身份登录并创建
Management Gateway 装置安装 速安装指南》。
和确认 admin（管理员）帐户的密
人员/用户指南》。 警告：已连接的串行设备不得超
码。
过 13 伏特。

590-1480-631D 3
AVOCENT® UNIVERSAL MANAGEMENT GATEWAY 装置
快速安装指南

Avocent® Universal Management Gateway 6000 装置正面

6 7

注意：配线架不宜用作装置与 8. 打开装置 c.单击表中的 eth0 条目，然后使

IQ 模块的连接点，因为它会带来 装置配有双电源，可提供冗余保 用下拉菜单将方式更改为
距离、电源、或视频质量控制功能 护。要打开装置，请先将电源线插 “静态”。
问题。如果去除配线架后问题仍 入装置，然后再将其插入电源。 d.分配所需的 IP 地址并单击
旧存在，请联系技术支持人员。 最后，打开与装置相连的设备。 “应用”。
6. 进行本地连接或通过控制台 9. 分配 IP 地址 注：有关使用命令行界面分配
端口连接 可通过 DHCP 获取 IP 地址，或 IP 地址的说明，请参阅
您可以通过 VGA 控制台或 CLI 可使用 VGA 或 CLI 设置端口分 《Avocent® Universal
设置端口配置和管理本装置。使 配静态 IP。
Management Gateway 装置命令
用提供的 RJ45 至 DB9 交叉转
换器，将终端或工作站连接到
注：如果使用 DHCP，您必须首 参考指南》。
CLI 设置端口。终端设置要求 先查看网络 DHCP 服务器上的
为：9600、8、N 和 1，无流量控 DHCP 租约，找到分配到本装置
制和 ANSI 仿真。 的 IP 地址。然后使用浏览器访问
https://<装置 IP> 以连接到本装
7. 连接 USB 设备 置。
您可以使用本装置前面的 USB 端
如果要使用 VGA 分配 IP 地址，
口连接键盘、录像机、鼠标或其他
支持的 USB 设备。 请执行以下步骤：
a.以 admin（管理员）身份登录
本装置的 web 用户界面。
b.单击“管理”选项卡下的“网络
设置”。

如需联系 Vertiv 技术支持：请访问 Vertiv.com

© 2019 Vertiv Group Corp. 保留所有权利。Vertiv 和 Vertiv 徽标是 Vertiv Group Corp. 的商标或注册商标。本文提及的所有其他名称和徽标均为其各自所有者的产品名称、商标或注册商
标。尽管我们已采取适当措施确保本文件的准确性和完整性，但对于因使用这些信息或任何错误或遗漏而造成的损害，Vertiv Group Corp. 概不承担任何责任和义务。规格的更改将不另
行通知。

4 590-1480-631D