CAT7105

2.0A High Efficiency Step-Down DC/DC Converter

Free Datasheet http://www.datasheet4u.com/

 CAT7105
2.0A High Efficiency Step-Down DC/DC Converter

Features Application

High Efficiency up to 95% Set-Top-Box, DVD, LCD Displays

4.75V to 23V Wide Input Voltage Range Battery Charger and High Power LED Power

Output Adjustable from 1.23 to 21V Supply

2.0A Output Current Distributed Power System

380kHz constant Frequency Operation Data comm. xDSL CPE

Current Mode Operation

Over-temperature Protected Pin Configuration

Over Current Protection

Under Voltage Lockout

25µA Shutdown Current

SOP8 Package

RoHS Compliant (100% Green available)

General Description

The CAT7105 is a high efficiency and high output

current step-down DC/DC converter that Ordering Information
integrates a low resistance high side NMOS.
Including on the substrate with the listed features Part Number Package Ship
are a high performance voltage error amplifier CAT7105CA 8L SOP (Green) 2500/ Tape & Reel
that provides tight voltage regulation accuracy
under transient conditions; an under voltage
lockout circuit to prevent start up until the input
voltage reaches 4.75V; an internally set soft start
circuit to limit inrush currents; and other features
include an over current protection and thermal
shutdown. The CAT7105 is available in a 8 pin
SOIC package.

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 2/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Pin Description

Pin Symbol Description

High Side Gate Drive Boost Input. A capacitor must be connected from SW to BS. This capacitor
1 BS
boosts the gate drive to the internal NMOS above VIN to fully turn it ON.
2 VIN Power Supply Pin. The input voltage for the power supply is connected to Pin2.
Power Switch Output. This is the output of a power MOSFET switch connected directly to the
3 SW
input voltage.
4 GND Ground Pin. This is the ground reference connection for all components in the power supply.
Voltage Feedback Pin. This is the input to an error amplifier, which drives the PWM controller. It’s
5 FB
necessary to connect this pin to the actual output of power supply to set the DC output voltage.
Compensation Pin. This pin is used to compensate the regulation control loop. Connect a series
6 COMP
RC network from COMP pin to GND pin to compensate the regulation control loop.
7 EN Enable Pin. This input provides an electrical ON/OFF control of the power Supply.

8 NC No Connection

Function Block Diagram

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 3/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Typical Application
C12 10nF

R1
Vin=4.75V~23V
Vout=1.23V*(1+R1/R2)
R2

CAT7105 D1
U1 B320A Vout
FB 5 4 L1
COMP 6 FB GND 3 SW 1 2
EN 7 COMP SW 2 Vin
SS 8 EN VCC 1
NC BST C1 C2 C3 C4
C5 C6 10uF 10uF NC 100uF
C7 C8 C9 0.1uF 22uF
NC NC

C10
R3 BST

0.1uF

R4 100K
EN

Vin C11
2

JP1 0.1uF
3 1

ON OFF

*note: The recommended applications shall be customer design-in orientation to fit each customers demand. Based on the nature of customers

demand-oriented, please contact CAT or agent for design support service.

R1 R2 R3 C8 L1
V out=5V 68K 22K 15K 2nF 15uH
V out=3.3V 16.8K 10K 10K 2nF 6uH
V out=1.8V 4.7K 10K 5.6K 1nF 4.7uH

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 4/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Absolute Maximum Ratings
Input Supply Voltage………………………….GND - 0.3V to +23V ESD Classification……………………..….…Class 2
SW Voltage …………………………………………- 0.3 to VIN+0.3V Junction Temperature Range ………………………… 150°C
o
Other Pins …………. ………………..- 0.3V to +6V Operating Temperature ………..…….. -20 C to 85°C
o
Boost Voltage ………..……………Vsw-0.3V to Vsw+6V Storage Temperature Range ………..-65 C to 150°C
SW Peak Current ………………… ….3.0 A Lead Temperature (Soldering 10s) ……..……. 260°C
*note: The IC has a protection circuit against static electricity. Do not apply high static electricity or high voltage that exceeds the performance of the

protection circuit to the IC.

Electrical Characteristic
(Recommended Operating Conditions, Unless Otherwise Noted; VIN = 12V; TA = 25 oC))

Parameter Test Conditions Min Typ. Max Unit

Supply Voltage 4.75 23 V

Shutdown Supply Current VEN = 0V 25 50 µA
Regulated Feedback Voltage 4.75V≦VIN≦23V 1.19 1.23 1.26 V
Error Amplifier Trans conductance △ICOMP = ±10µA 500 800 1120 µA/V
Current sense to COMP Trans
3.8 A/V
conductance
Current Limit 3.0 A
SW Leakage Current VEN = 0V, VSW = 0V 10 µA
High Side On Resistance 0.25 Ω
Low Side On Resistance I 10 Ω
Oscillation frequency 320 380 440 KHz
Short Circuit Oscillation Frequency VFB=0V 40 KHz
Maximum Duty Cycle VFB=1.0V 90 %
Minimum Duty Cycle VFB=1.5V 0 %
Under Voltage Lockout Threshold VIN Rising 3.9 4.1 4.3 V
Under Voltage Lockout Threshold
200 mV
Hysteresis
Thermal Shutdown Threshold 160 ℃
EN High Level 2.6 V
EN Low Level 0.9 V
EN Input Current VEN = 0V 1.1 1.8 2.5 µA

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 5/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Function Description
The CAT7105 is a constant frequency current Maximum Load current
mode PWM step-down converter. It regulates The CAT7105 can operate down to 4.75V input
input voltages from 4.75V to 23V down to an voltage; however the maximum load current
output voltage as low as 1.23V, and is able to decreases at lower input due to large IR drop
supply up to 2A of load current. on the main switch and low side switch. The
slope compensation signal reduces the peak
Oscillator Frequency inductor current as a function of the duty cycle to
Slope compensated current mode PWM control prevent sub-harmonic oscillations at duty cycles
provides stable switching and cycle-by-cycle greater than 50%.
current limit for superior load and line response
and protection of the internal main switch and Enable
synchronous rectifier. The CAT7105 switches at The EN pin provides electrical on/off control of
a constant frequency (380 KHz) and regulates the regulator. Once the EN pin voltage exceeds
the output voltage. During each cycle the the threshold voltage, the regulator starts
PWM comparator modulates the power operation and the internal slow start begins to
transferred to the load by changing the inductor ramp. If the EN pin voltage is pulled below the
peak current based on the feedback error threshold, the regulator stops switching and the
voltage. During normal operation, the main internal slow start resets. Connecting the pin to
switch is turned on for a certain time to ramp the ground or to any voltage less than 0.9V will
inductor current at each rising edge of the disable the regulator and activate the shutdown
internal oscillator, and switched off when the mode.
peak inductor current is above the error voltage.
When the main switch is off, the low side Under Voltage Lockout
MOS will be turned on immediately and stay on The CAT7105 incorporates an under voltage
until either the next cycle starts. lockout circuit to keep the device disable when
VIN is below the UVLO start threshold. During
Short Circuit Protection power up, internal circuit are held inactive until
The CAT7105 has short circuit protection. When VIN exceeds the UVLO start threshold voltage.
the output is shorted to ground, the oscillator Once the VULO start threshold voltage is
frequency is reduced to prevent the inductor reached, device start-up begins. The device
current from increasing beyond the N MOS operates until VIN fall below the UVLO stop
current limit. The NMOS current limit is also threshold voltage. The typical hysteretic in the
reduced to lower the short circuit current. The UVLO comparator is 200mV.
frequency and current limit will return to the
normal values once the short circuit condition Boost Capacitor
is removed and the feedback voltage reaches Connect a 0.01µF low ESR ceramic capacitor
1.23V. between the BS pin and SW pin. This capacitor

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 6/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
provides the gate drive voltage for the high side
MOSFET.

Thermal Shutdown
The CAT7105 protects itself from overheating
with an internal thermal shutdown circuit. If the
junction temperature exceeds the thermal
shutdown threshold, the voltage reference is
grounded and high side MOSFET is turned off.

Compensation
The system stability is controlled through COMP
pin. It will present a general design procedure to
help insure a stable and operational circuit. The
design in this data sheet is optimized for
particular requirements. If different conversions
are requires, some of the components may need
to be changed to ensure stability. The power
components and their effects will be determined
first, and then the compensation components will
be chosen to produce stability.

Output Voltage
The output voltage is set using the FB pin and a
resistor divider connected to the output as shown
in Figure1. The FB pin voltage is 1.23V, so the
ratio of the feedback resistors sets the output
voltage according to the following equation:
VFB = VOUT * R2 / (R1 + R2)
Thus the output voltage is:
VOUT = 1.23 * (R1 + R2) / R2

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 7/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Package Dimensions

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 8/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Classification Reflow Profiles
Reflow Profile Green Assembly
Average Ramp-Up Rate (Tsmax to Tp) 3℃/second max.
Preheat
-Temperature Min(Tsmin) 150℃
-Temperature Max(Tsmax) 200℃
-Time(tsmin to ts tsmax) 60-180 seconds
Time maintained above:
217℃
-Temperature(TL)
60-150 seconds
-Time(tL)
Peak Temperature(Tp) 260 +0/-5 ℃
Time within 5 ℃ of actual Peak Temperature(tp) 20-40 seconds
Ramp-Down Rate 6℃/second max.
Time 25℃ to Peak Temperature 8 minutes max.
Note: All Temperature refer to topside of the package, measured on the package body surface.

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 9/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105
Carrier Tape & Reel Dimensions

CARRIER TAPE WIDTH C NOMINAL T W TOTAL LENGTH

12mm 76.2mm 0.06±0.01mm 9.3±0.1mm 300M

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 10/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 11/12
2007 Chip Advanced Technology Inc. – All Right Reserved.
 CAT7105

HEADQUARTERS:
3F, No.1, Jin-Shan 8th St., Hsin-Chu City 300, Taiwan (R.O.C.)
Tel: +886-3-666-8301
Fax: +886-3-666-8630
Website: http://www.chipadvanced.com

TAIPEI OFFICE:
4F, No.112, Jhouzih St., Neihu District, Taipei City 114, Taiwan (R.O.C.)
Tel: +886-2-87516119
Fax: +886-2-87516359

Information furnished is believed to be accurate and reliable. However, CAT Inc. assumes no
responsibility for the consequences for use of such information nor for any infringement of patents or
other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of CAT Inc. Specifications mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information if
previously supplied. CAT Inc. products are not authorized for use as critical components in life support
devices or systems without the express written approval of CAT Inc.

The CAT logo is a registered trademark of Chip Advanced Technology May-2007 Rev:0.94 12/12
2007 Chip Advanced Technology Inc. – All Right Reserved.