Scribd
Upload
174 views19 pages

Dimensioning

The document discusses the topic of dimensioning in engineering graphics. It covers elements of dimensioning such as lines, arrowheads and leaders. It also discusses different dimensioning systems and rules as well as methods for dimensioning linear and circular features.

Uploaded by

Shubham Mehta
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
174 views19 pages

Dimensioning

The document discusses the topic of dimensioning in engineering graphics. It covers elements of dimensioning such as lines, arrowheads and leaders. It also discusses different dimensioning systems and rules as well as methods for dimensioning linear and circular features.

Uploaded by

Shubham Mehta
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

ENGINEERING GRAPHICS

Topic:
Dimensioning
Dimensioning

▪ Dimensioning refers to the act of giving dimensions.


45

45

60 80
Elements of Dimensioning

80

Front View
Closed filled arrowhead

3
Closed filled arrowhead

Good & Bad Practices


Leader

Ø30
Systems of Dimensioning

▪ There are two systems of dimensioning:


a) Aligned System
b) Uni-directional System
Systems of Dimensioning
Aligned System
In the aligned system, dimensions are placed perpendicular to the
dimension line so that they may be read from the bottom or
right-hand side of the drawing sheet. Dimensions are placed at
the middle and on top of the dimension lines.
Systems of Dimensioning
Unidirectional System
In the unidirectional system, dimensions are placed in such a way
that they can be read from the bottom edge of the drawing sheet.
All dimensions are placed at the middle and are inserted by
breaking the dimension lines at the middle.
Rule of Dimensioning
1. Between any two extension lines, there must be one and only one dimension line
bearing one dimension.
2. As far as possible, all the dimensions should be placed outside the views. Inside
dimensions are preferred only if they are clearer and more easily readable.
3. All the dimensions on a drawing must be shown using either Aligned System or
Unidirectional System. In no case should, the two systems be mixed on the same
drawing.
4. The same unit of length should be used for all the dimensions on a drawing. The
unit should not be written after each dimension, but a note mentioning the unit
should be placed below the drawing.
5. Dimension lines should not cross each other. Dimension lines should also not cross
any other lines of the object.
6. All dimensions must be given.
7. Each dimension should be given only once. No dimension should be redundant.
.
Methods of Dimensioning
For dimensions in series, there are three methods:

a) Chain Dimensioning
b) Parallel Dimensioning
c) Combined Dimensioning

Adopt any one of these methods.

i. Chain dimensioning (Continuous dimensioning): All the dimensions


are aligned in such a way that an arrowhead of one dimension touches tip-
to-tip the arrowhead of the adjacent dimension. The overall dimension is
placed outside the other smaller dimensions.
Methods of Dimensioning

CHAIN DIMENSIONING

10 10 10
Methods of Dimensioning
Parallel dimensioning (Progressive dimensioning):

All the dimensions are shown from a common reference line. Obviously, all
these dimensions share a common extension line. This method is adopted
when dimensions have to be established from a particular datum surface.
Methods of Dimensioning

PARALLEL DIMENSIONING

10

20

30
Methods of Dimensioning
Combined dimensioning:
When both the methods, i.e., chain dimensioning and parallel
dimensioning are used on the same drawing, the method of dimensioning
is called combined dimensioning.
Methods of Dimensioning

COMBINED DIMENSIONING

10 10

30
Dimensioning of Circular Features
Ø 12

Ø 30

Ø 20
Dimensioning of Circular Features

R10

R5
R5
Thanks

You might also like