Department of Education
Region 02
Schools Division of Nueva Vizcaya
BUGKALOT HIGH SCHOOL
New Gumiad, Dupax del Norte, Neuva Vizcaya
Email: [email protected]
School ID: 300624
EXIT ASSESSMENT IN EIM 10
Name: ___________________ Year & Section: ____________ Score: _______
Multiple Choice. Choose the letter of the correct answer and write the letter of the correct answer
on the separate answer sheet provided.
1. These symbols are frequently used in panel diagrams which indicate the actual object.
a. architectural b. block c. pictorial d. schematic
2. These are electrical materials in which splices and joints are being made.
a. Utility box b. Junction box c. Square Box d. Electrical Boxes
3. It is an electrical device used in controlling the flow of current in a circuit or even the entire
circuit.
a. Flush type switch b. Tumbler switch c. Main switch d. Switches
4. The amount of electrical pressure in a circuit. It may be produced by generators, batteries,
photocells, thermocouples, piezoelectricity, or static electricity.
a. Current b. Resistance c. voltage d. Power
5. This is a tool used for gripping, holding, and cutting electrical wires, cables and even small nails.
It is usually use by line men in doing heavy tasks.
a. Combination pliers c. Long nose pliers
b. Electricians knife d. Wire stripper
6. How much voltage is needed in a circuit that includes a 3 ohms heating element that draws 4 A?
a. .75 V b. 1.33 V c. 12 V d. 15 V
7. How much resistance is needed in a circuit that draws a 4A current connected to a 36 V supply?
a. .11Ω b. 9Ω c. 12Ω d. 144Ω
8. In a series circuit, what will happen if you remove one bulb?
a. The circuit does not function. c. The circuit functions normally.
b. The other bulbs still glow. d. The brightness of the other bulbs becomes dimmer.
9. Calculate the amount of current flowing in a circuit if it has a 12 V source and a resistance of 3Ω.
a. .25 A b. 4 A c. 9 A d. 36 A
10. Why are fuses and circuit breakers used in circuits?
a. Fuses and circuit breakers open the circuit when a large amount of current flows through
the circuit.
b. Fuses and circuit breakers increase the efficiency of the appliances within the circuit.
c. Fuses and circuit breakers insulate the connection in the circuit.
d. Fuses and circuit breakers can help out the electrical consumption.
11. How do you show the simple way the flow of current in the circuit? By drawing a/an ______.
a. Wiring diagram c. schematic diagram
b. Electrical plan d. pictogram
12. Your fuse at home has “blown” up many times. Which of the following will you do to solve this
problem and prevent it from happening again?
a. Connect appliances in series instead of parallel.
b. Do not use too many appliances at the same time.
c. Plug two or three appliances in one outlet.
d. Connect an additional fuse to your circuit.
13. A pocket-sized tool used to test the presence of the current in a line wire or circuit.
a. Pull-push rule b. Ruler c. Test light d. Wire gauge
14. It is used to measure the voltage, resistance, and current of a circuit. It is connected in parallel or
series with the circuit depending on what to measure.
a. Ammeter c. Ohmmeter
b. Micrometer d. Voltmeter-Ohmmeter-Milliammeter
15. If you arrange or put every necessary item in good order so that they can be easily picked for use,
you are doing _________.
a.Sanitizing b. Sorting c. sweeping d. systematizing
16. It is the chance or probability that a person will be harmed.
a. Accident b. Hazard c. injury d. risk
17. When you performed computation of load, the total ampere rating of all the circuit is 42.5
amperes.
What is the best recommendation will you recommend to the owner of the house?
a. Use 40 amperes main breaker and #10 AWG service entrance.
b. Use 60 amperes main breaker and #6 AWG service entrance.
c. Use 60 amperes main breaker and #8 AWG service entrance.
d. Use 60 amperes main breaker and #10 AWG service entrance.
18. How do you control control a lamp in one location. By using _____.
a. SPST Switch b. DPDT c. 3-way switch d. Schematic diagram
19. When operating the portable disc grinder the grinding disk should be positioned
so the sparks and grit are thrown _____________.
a. away from the operator. c. down to avoid hitting others.
b. up to avoid hitting others. d. away from the operator and others in the work area.
20. Why do we turn the drill on before attempting to drill a hole?
a. see if the drill operates.
b. check if the power cord is good
c. see if the drill bit is running true.
d. make sure the chuck key has been removed.
Prepared by:
NOEL L. BUA-AY
Subject Teacher
Checked:
LANDO A. KILOP
Department Head
Noted:
RODELIO B. DELA CRUZ
School Head
