Quick Start Wireless DICOM

The OEC Wireless DICOM networking module enables wireless connectivity for DICOM data transfer (including images, reports, and schedules) on the OEC Elite system.

User interface
Wireless On/Off indicator. This LED is located on the back of When the system is connected to
the Workstation and indicates the wireless status: a network, a network status icon
Display Wireless Capability displays in the status bar on left side
of the screen. The network status
Off Disabled or switched off; switch in down (off) position
icon indicates the network’s status.
Solid Blue Enabled and switched on; switch in up (on) position

Wireless status indicator. This LED is located on the back of the Connected No network
(wired or wireless) connection
Workstation and indicates the status of the connection:
Display Connection Status Note: Wired Ethernet connections
Off Wireless off or wired connection override wireless connections. If a wired network connection is
established, wireless is disabled automatically.
Solid Amber Not authenticated to a wireless connection

Solid Green Connected and authenticated

Setting up wireless
If the Workstation network settings are modified, 2. Set the IP address to 192.168.137.1.
it can affect network communications. Ensure that 3. Set the Subnet Mask to 255.255.255.0.
the network settings are correct: 4. Verify that the Connected icon displays in the
status bar.
1. On the Workstation, touch the Applications See the Set up network configurations section
tab, touch Setup, and then touch Network. of the GE OEC Elite® Operator Manual for more
The Applications > Setup > Network information about network settings.
Configuration screen displays.

Copying images wirelessly

Send DICOM images to PACS wired or wirelessly. The Wireless DICOM adds to your system’s DICOM
1. On the Images screen, touch Copy To.... capabilities, but does not change the basic DICOM
2. On the Copy To... screen, select the DICOM functionality. For information on DICOM features,
store server. refer to the system’s operator manuals. Existing
3. Select images to copy and touch Copy. DICOM workflow remains unchanged. Refer to the
4. Wait for the progress bar to complete. Transfer system’s user manual for information on setting up
is complete. a DICOM store server. Refer to the system’s service
GE OEC Medical Systems, Inc. 5777107-1EN-03 manual for information on setting up wireless
384 Wright Brothers Drive Rev 1 ©2017 DICOM functionality, or call for service.
Salt Lake City, UT 84116 U.S.A. GE OEC Medical Systems, Inc.
(801) 328-9300 All Rights Reserved
Quick Start Wireless DICOM
Technical specifications Label, symbols, and compliance
These symbols appear on the label, located on the right side of the Workstation:
Model Wireless DICOM
IP Addressing Supports Static and DHCP This symbol indicates that the system includes an RF transmitter.

Communications LAN: 10/100/1000 MB This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
Wireless LAN: IEEE 802.11a/b/ device may not cause harmful interference, and (2) this device must accept any interference received, including
g/n/ac interference that may cause undesired operation. The FCC ID identifies the FCC equipment authorization
associated with the transmitter.
Security Supports security measures that
Methods do not require file uploads. These symbols also appear on the system:
Currently supports WEP-64,
WEP-128, WPA-PSK (TKIP), The CE Mark of Conformity indicates that the product is in compliance with the essential requirements and other relevant provisions of
WPA2- PSK (AES-CCMP), PEAP: the Radio Equipment Directive 2014/53/EU. Hereby, GE OEC Medical Systems, Inc. declares that the radio equipment type OEC Elite is in
EAP-MS-CHAP v1 & v2, LEAP, compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
EAP-FAST security methods. http://www3.gehealthcare.com/en/Global_Gateway. Select the desired language and then Support > Documentation Library.

Frequency 5 GHz 2.4 GHz The RCM symbol indicates compliance with ACMA radiocommunications regulatory arrangements and mandatory technical standards as
Modulation (802.11 a/n/ac) (802.11 b/g/n) required for Australia and New Zealand.
Frequency Band:
5.15 GHz – 2.400 GHz – Additionally, this device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
(country-
5.725GHz 2.4835 GHz device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of
dependent) the device. The IC number identifies the ISED certification number associated with the transmitter.
Modulation: OFDM, BPSK, OFDM, DSSS,
QPSK, 6 QAM, CCK, QPSK,
64 QAM, 256 BPSK, 16 QAM, Warnings and safety
QAM 64 QAM
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
Transmit EIRP: +20 dBm +23 dBm authority to operate the equipment.
Transmit ERP: +15.86 dBm +14.55 dBm Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e wireless LAN devices may
AT BE BG HR CY CZ DK EE
not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e products are designed for use
only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user
FI FR DE EL HU IE IT LV of these products, you are responsible for ensuring that the products are used only in the countries for which they were
LT LU MT NL PL PT RO SK intended and for verifying that they are configured with the correct selection of frequency and channel for the country of
use. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national
SI ES SE UK law and may be punished as such.
This product is restricted to indoor use.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: To comply with FCC’s RF Exposure Safety Limits for general population / uncontrolled exposure, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or transmitter.