BS PARVEEN IND. PVT. LTD. TECHNICAL MANUAL HYD. TOOL CATCHER CATCH SIZE: 1.00”-2.313”, CONN: 5.3/4”-4 ACME BOX x PIN SPS # 995-A REV-0 PRODUCT INTRODUCTION: ‘The PARVEEN Hydraulic tool catcher is designed to engage and retain the tool fish neck or rope socket of any tool string that has accidentally collides with the stuffing box or grease injection head, and strips off the wire line from the rope socket. It will prevent the tool string from falling Downhole. The Hydraulic tool catcher is released hydraulically by ut ing a hand pump, FEATURES ‘+ Standard design is without ball check valve, optional tool with ball check valve upon request. SAFETY NORMS: ‘+ Only properly trained and qualified personnel should be engaged in testing PARVEEN ‘equipment. ‘+ Make sure lifting and handling equipment is rated to safely handle the load of any equipment lifted by the handling systems whether they be cranes, forklifts or the like. Never work under a suspended load. Chains, cable and rope can break and knots can fail. Always error on the side of safety. All pressure gauges and measuring instruments shall be calibrated and certified by properly trained and qualified personnel. ‘+ Make sure all pressure lines and fittings are in good, serviceable condition. Fitting and/or line failure can cause serious injury. ‘+ With the exception of shop air tests for initial leak detection immediately after assembly, all pressure testing shall be carried out behind blast walls or within @ blast proof test bay. Any measurements of movement conducted during the procedure must be observed and conducted remotely. ‘+ When conducting shop air tests, make sure that the test is conducted in a safe manner and personnel conducting the test are standing a safe distance from the equipment being tested, Care should be taken and procedures followed to reduce all risk, ‘+ Personnel shall not enter the test area with pressure applied to the fixture. ‘* Any spillage must be immediately cleaned and remediated to avoid environmental pollution hazards, WRITTEN BY: T.S. APPROVED BY: P.P.iat PARVEEN IND. PVT. LTD. ‘TECHNICAL MANUAL HYD. TOOL CATCHER CATCH SIZE: 1.00"-2.313", CONN: 5.3/4”-4 ACME BOX x PIN ‘SPS # 935-A REV-0 BILL OF MATERIAL HYDRAULIC TOOL CATCHER W/O BALL CHECK VALVE CATCH SIZE: 1.00"-2.313" WITH CONN: 5.34”-4 ACME BOX x PIN IASSY. PART No. 2622302100. TEM ory.| PART NO. | REV DESCRIPTION 7 [1 | wezeioeo1 | 0 TOP SUB 2 [4 | ageaioe02 | 0 | ACTUATOR SPRING 3 1 282-4102-03-05A oO RELEASE ACTUATOR 4 2 50233V o 'O' RING NO. 233 5 [4 | s0zsvt_| 0 | BACK UP.AING, sizé-233 6 | 1 | 2eeatoew-or05A | 0 | PISTON 7 4 50235V 0 'O' RING NO. 235 3 | 2) s0asevi | 0 | BACKUP RING. 256 o [1 | stasav | 0 O-RING SI: 254 10 1 (282-4102-05 oO COLLET SPRING pd 4 282-4102-06-05A 0 COLLET HOUSING ve Lot | si2-t0223.07 | 0 | COLLET 10 CATON TVS TORaT@ FR) 1 [-aae-410017.07 | "0 | COLLET (TO CATCH 1. 00°70 1.75"FN) [1 | 28e-st0amos | 0 | MANDREL ta [1 | eazaie%00.09 | 0 Borrow suB is | 1 | aoo0s.01-s | 0 | QUICK UNION NUT SPLIT TWPE 6-4 AONE 16 # 440204-01 oO SPLIT RING Q,NUT 5.3/4"-4 ACME [1 | sav [0 [O-RING Nossa te [tetra | 0 ELBOW 1 NPT MIX 1 [1 | aocta-tox | 0 abc tar NPT xF 20_| 1 | 28221a110.02 | 0 | PROTECTORPLATE zi | 1 | oaacare | 0 S00. HO. CAP SCREW 118-20 UNG X 5" LONG 22 4 86A1152C, oO CONNECTOR 1/4" NPT(M) X_1/4" NPT(F) X 2.0" LG 23 4 88CE2EB o HEX SOC SET SCREW (3/8"-16 UNC X 1/2" LG.) 24 1 440200-17 0 | THREAD PROTECTOR, 5.3/4"-4ACME (PIN) 261 | 440200-18 | 0 | THREAD PROTECTOR. 6.34" 4ACME (GOX) WRITTEN BY: T.S. APPROVED BY: P.P.BS PARVEEN IND. PVT. LTD. TECHNICAL MANUAL HYD. TOOL CATCHER CATCH SIZE: 1.00”-2.313”, CONN: 5.3/4”-4 ACME BOX x PIN SPS # 995-A REV-0 BILL OF MATERIAL REDRESS KIT FOR HYDRAULIC TOOL CATCHER W/O BALL CHECK CATCH SIZE: 1.00"-2.313" WITH CONN: 5.34”-4 ACME BOX x PIN ASSY. PART No. : 282-2302100-H-R TEM) ary. | PartNo. | REV DESCRIPTION 1 [2 | soaav 0 ORNGNO.238 2 | «| s0asevi 0 | BACK UP-RING-238 3 1 50235V 0 | 'O'RING NO. 235 a [2 | somasvi 0 BACKUP RING:- 285 Spot s0asav [0 TORING Sze. 254 Sopot satay 0 RING NO 8H2 DISASSEMBLY PROCEDURES 1. Remove soc. head cap screw (21) from the top sub (1) allowing the protector plate (20) to be removed. Remove Elbow (18) and QDC (19) from the top sub (1) Unscrew the top sub (1) from the bottom sub (14) and lift clear. Slide out the actuator spring (2) from the release actuator (3). Pull out the release actuator sub assembly from bottom sub (14). Slide out the union nut (15) from bottom sub (14) and lift clear. Disassemble the release actuator assembly a) Unscrew and remove release actuator (3) from mandrel (13) b) Slide out the piston (6) and collet spring (10) from the mandrel (13). c) Push the mandrel (13) through the collet (12) and lift clear. d) Using the pliers, remove the collet (12) from the collet housing (11). 8. Remove all o-tings and backup rings. 9. Clean & inspect parts for damage. NOMEN ASSEMBLY PROCEDURES 1. Install all o-rings & backup rings as per assembly drawing Insert the collet housing (11) and collet (12) into the bottom sub (12) 3. Insert the mandrel (13) into the collet housing (11) till the bevel of the mandrel (13) sits on the collet (12). Slide the piston (6) and the collet spring (10) across the mandrel (13) threaded end. Insert the release actuator (3) into the piston (6) then sorew the mandrel (13) into the release actuator (3). Slide the union nut (15) across the bottom sub (14) Slide the actuator spring (2) across the release actuator (3). Make up the top sub (1) onto the bottom sub (14), Assemble Elbow (18) and QDC (19) in the top sub (1). 0. Insert soc. head cap screw (21) through the holes of protector plate (20) and assemble the top sub (1). 11, The hydraulic tool catcher is completely assembled and ready for pressure testing. we meee WRITTEN BY: T.S. APPROVED BY: P.P.\ BOTTOM CONN WORE PRESSURE 76000 psi AYO. PRESSURE 3000 pst FSH SE ‘oar=2.515" FN BOTTOM CONN. "4 ACME (4.00") PIN TOP CONN. 4 ACME (4.00") BOX PART NO 782-2302 100-H |, UNLESS OTHERWISE SPECFEED PARVEEN INDUSTRIES VT. LTD ats uo. Tene LCC Kt) E88 Mites [a 30 HE see SAS Ss aun TaTERO EAT TREAT Buamna oar REVERE [6-00 NOT SCALE DRAWING, seat NTS [ona we NOTED =oPARVEEN IND. PVT. LTD. TECHNICAL MANUAL HYD. TOOL CATCHER CATCH SIZE: 1.00”-2.313”, CONN: 5.3/4”-4 ACME BOX x PIN SPS # 995-A REV-0 STORAGE RECOMMENDATIONS: The following procedures are recommended: All completion equipment should be stored indoors. The indoor environment should be air conditioned and/or heated to prevent large temperature variations and to control the humidity. If the indoor facilities are not available, the equipment should at least be under a roofed shelter and not exposed to rain or precipitation. Periodic inspection of the equipment should be made to ensure no corrosion or dirt has accumulated and inspect equipment well enough in advance of a completion that repairs or redress are possible prior to the completion if necessary. If corrosion or dirt buildup is observed, the equipment should be cleaned thoroughly and action taken to prevent this, buildup in the future. All metallic components should be protected with light oil or suitable corrosion inhibitor. This includes the mandrel bore. Exposed elastomers should be covered with polythene net or protected with bubble wrap then covered with black polyethylene sheet to protect against light, dirt, and mechanical damage. All exposed threads should be liberally greased with a suitable thread compound and protected with approved closed-ended thread protectors at all times. Inventory should be rotated to reduce the age of the inventory (first in; first out). The oldest equipment should be used first before newly received equipment is used, HANDLING AND PROTECTION: For proper handling of products an overhead crane, wooden box, pallets and bins of appropriate sizes are to be used. if larger assemblies are properly boxed or mounted on. ‘wooden skids forklifts may be used to move equipment. Ground/lappedihoned/polished surfaces shall be cleaned and anti-corrosive oil to be applied, Components without seals surfaces are to be covered with polythene net or protected with bubble wrap. Card board sheets may be used as a separator between components kept in boxes or trays to avoid damage. Tubing connections are to be covered with thread protectors and body joints threads shall be protected with polyethylene net. Personnel charged with handling parts and assemblies shall be properly trained and certified to ensure against scratch/dent marks or any other damage to parts takes place. WRITTEN BY: T.S. APPROVED BY: P.P.