GYM GARAGE
HOME
WORK
Copy. Consolidate. Simplify. 4-Button Rfid Remote Control
INSTRUCTIONS
REPLACE THESE FOBS
WITH ONE DEVICE
For use with most
Model Kf-001 125kHz RFID systems
Keysy Rewritable RFID reader
remote keyfob not included
Programming the 4. If the LED turned AMBER flip the
keycard/keyfob and repeat steps 1-3.
Keysy remote 5. If programming continues to fail
1. Place the Keysy remote on top of the (AMBER) move the Keysy remote to a
keycard/keyfob you wish to copy. different location on the keycard/keyfob
and repeat steps 1-3.
6. If programming continues to fail after
multiple attempts the card may not
be supported. Please contact
[email protected] to troubleshoot.
2. Press and hold the button you wish to Using the Keysy remote
program for 6 seconds until the LED on as keycard/keyfob
the Keysy remote blinks red. Release the
button and center the blinking LED on 1. To select the desired electronic key
the keycard/keyfob. press and release the previously
programmed button.
2. Hold the Keysy remote parallel to the
RFID reader (within a few centimeters).
The RFID reader should blink and/
or beep when the electronic key has
successfully been read.
3. If the LED turns GREEN you can now
use Keysy remote as the keycard/keyfob
or follow the How to make a duplicate
section.
3. If the Keysy remote fails to open the
door see the section Keysy Remote
Compatibility.
www.tinylabs.io/keysy continued....
Model Kf-001
Before going through these steps Keysy remote Battery replacement
must be programmed using the previous section.
How to make a duplicate
keycard/keyfob
1. Place the Keysy remote on top of the
included rewritable keyfob.
Battery warning
To prevent possible SERIOUS
INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately
notify doctor.
2. Make sure the LED is centered on top of To reduce risk of fire, explosion or chemical burn:
the rewritable keyfob. • Replace only with 3V CR2032 coin cell
3. Press the previously programmed button battery.
that you wish to duplicate 5 times. • DO NOT recharge, disassemble, heat
4. The RED LED will briefly blink as the above 212° (100°C) or incinerate.
rewritable keyfob is being programmed.
5. After a short period of time, the Keysy NOTICE: To comply with FCC and CE rules all
modifications to the equipment within are expressly
remote will blink GREEN 3 times prohibited, except for replacing the battery. THERE ARE
(success) or RED 3 times (failure). NO OTHER USER SERVICEABLE PARTS.
6. If programming fails, flip over the rewritable This device complies with part 15 of the FCC Rules.
keyfob and repeat steps 1- 5 above. Operation is subject to the following two conditions: (1)
7. Once successful, the rewritable keyfob This device may not cause harmful interference, and
(2) this device must accept any interference received,
can be used just like the original keycard/ including interference that may cause undesired operation.
keyfob. Tiny Labs Inc hereby declares that this wireless device
is in compliance with the essential requirements and
Keysy Remote Compatibility other relevant provisions of CE the RE Directive.
Due to inconsistencies between manufacturers, Use of this product constitutes acknowledgement
of the terms set forth below:
Keysy remote does not work on every RFID
The Keysy™ RFID Duplicator is intended as a tool to
reader. In the case where Keysy remote does conveniently store multiple radio frequency identification
not work with a specific RFID reader it can still (RFID) keys for later recall and use. Tiny Labs, Inc. makes
be used to make a duplicate copy of a keycard/ no claims that the user of the product will experience
keyfob onto the included rewritable keyfob. any increased level of security by using Keysy™. The user
of this product does so at their own risk. Therefore the
user of this product releases and forever discharges Tiny
Battery Labs, Inc., and their stockholders, successors and assigns,
Only program the Keysy remote with a fresh agents, attorneys, and representatives from any and all
claims, demands, debts, liabilities, actions, causes of action,
CR2032 battery. If programming fails after suits, contract controversies, obligations, and judgments,
repeated tries please replacethe battery and whether in law or equity, arising out of or relating to
retry the programming sequence. the use and operation of the Keysy™ RFID Duplicator.
www.tinylabs.io/keysy
