Instruction

Manual




























Start to use


Install the app





Connect to camera AP





Add camera




Get real-time video, point-to-point
usage.Configure camera WIFI information




Connect to router




Configure camera WIFI




Turn off camera AP, WIFI viewing
Indicator status:
Start: red light is always on
Hotspot mode: Blue light flashes slowly
Networking status: blue light is always on
Charging status: green light is always on
Fully charged: green light is off

button:
ON / OFF: (press the button once to turn on the camera, press and hold for 5 seconds
to turn off)
MODE: reset button (long press for 5 seconds, the release indicator goes out to reset)

Precautions:
The camera only supports 2.4G WiFi frequency, not 5G WiFi frequency
If you have forgotten your password or do n’t know what status, please reset the
camera to the factory state
If you need to change the router or switch back to the WiFi hotspot mode, use the
MODE button to reset the camera.

Mobile phone App installation

1. Download and install HDWifiCamPro from Apple Store for IOS, and search on GooglePlay for
Android. For easy installation, please scan the below QR code to download and install
HDWifiCamPro. If your device fails to connect to GooglePlay, please scan the below APK QR code
for download and installation. Note: It is recommended to use the QR code scanning software
that comes with your browser or a third party to scan and download App. Direct download and
installation of App files is not supported by WeChat scan.

2. AP hotspots connected to the camera
Tap on the ON/0FF key to power on, the red light is always on after the turn-on, wait 5 seconds
blue light flashing AP hot spot on
Turn on your phone's WiFi settings and find the AP hotspot DGK-XXX-XXX that starts with DGK,
the same as the back of the camera.
Click Connect to this WiFi hotspot to show that the connection is successful before proceeding
to the next step.

Open the APP click "+" on the "plus" to add a new camera. Click Add online camera to go to the
camera's add page.


3. There are two ways to quickly enter the camera UID: A. Scan the QR code on the camera; B.
Search the camera through the local network.

4. Fill in the camera name and the P2P password. The default P2P password is 6666. Confirm and
click Ok. Camera is added successfully. It is recommended to modify the P2P access password
after setting up the camera.




5. After the camera is showed online, then click the camera you just added to watch the real-time
video. You can control the device in the video interface.



6. Icons and buttons for video pages

This icon is a function of other products and is useless in this product.

Users can hear the camera sound and have two-way voice intercom
(need to purchase camera for support).

Take snapshots and record video files

Flip images vertically and horizontally

Camera light switch and night vision light switch

 Adjust brightness and contrast, tune intercom sound

Watch videos in the SD card

1. Other features of the page

Watch the current real-time video

View screenshots taken by the camera

View video files for your mobile device

View camera alarm event record

Camera setting

1. Click the gear button at the back to open the advanced configuration page of the camera.

2. Modify the WIFI connection. Select WIFI Settings and the camera will show the available
Wi-Fi hotspots. Select your Wi-Fi network name (SSID), enter the Wi-Fi password and press
the finish key to connect. Note: After saving, if the camera is connected to WIFI, the
camera will disconnect the current connection to try a new WIFI network, which will cause
the camera in the App to be temporarily offline for about 1 minute.

4. SD card video recording setting: Set the mode and the screen size of SD card video recording.


Quickly set the camera to connect to the WiFi network

1. App choose to add camera "+"

2. Select Configure camera to connect to WIFI network

4. Click the WIFI configuration, and then verify that the displayed WIFI network name is the same
as the UID number of the device. Then return to APP.


5. After returning to the APP, the WiFi settings will pop up automatically. Click Manage WiFi
Network to start searching for WiFi automatically. After searching for WiFi, click and then
enter the password. Then click Finish. The WiFi setting is successful. Wait for the device to
restart. Please wait for the camera to automatically connect to the network after restarting.
After the network is successfully connected, the display device can be used remotely online.

Note: if the App always fails, try to check the following:
A. Camera indicator light does not flash slowly and AP is not turned on before you start
configuring Wifi
B. If the phone fails to connect to camera AP, you need to configure the phone to connect to
the AP hotspot of the camera.
C. Support ordinary routers.But public routers requiring login page authentication are not
supported.
D. Make sure there are no errors in network name, network password and UID when
configuring.
E. Wifi names and passwords in Chinese are not supported at this moment.
F. 5G Wifi signal is not supported.
G. Check whether the Wifi indicator light is always on, if yes, it means that the camera
networking is successful, please add an online camera directly, App may not detect a successful
camera configuration due to network shielding.
H. If WiFi is WEP encryption mode, change to WPA mode.

FAQ
1. Why the search tool is unable to detect the camera?
A: Please make sure if the network connection is good, turn off the firewall and security
software, and make sure the camera is connected to the router.

2. Why does the camera always require a user name and password, or an incorrect user?
A: The default password for the camera is 6666. If you forget your user name or password,
you can resume the camera to the default settings to get the default user name and
password.

3. How can I resume my camera to default settings?
A: Please press the reset button on the camera for about 5 seconds until the camera
restarts.

4. Why the image is blurred?
A: Remove the protective film of the lens. If it is still not clear, rotate the camera lens and
focus it so that you can get a clear image after focusing.