CX-LEM400

SERVICE MANUAL AEP Model

UK Model
Ver 1.1 2004. 09

CX-LEM400 is the Amplifier, CD player, Tape

Deck and Tuner section in XR-EM400.

CD Model Name Using Similar Mechanism NEW

Section CD Mechanism Type BU-30DBD64S
Optical Pick-up Name A-MAX. D
TAPE Model Name Using Similar Mechanism CX-LEM300
Section Tape Transport Mechanism Type CMAL5Z220A

SPECIFICATIONS

TUNER CD PLAYER
FM tuning range 87.5 MHz to 108 MHz Laser Semiconductor laser (λ = 780 nm)
FM usable sensitivity (IHF) 16.8 dBf Emission duration: continuous
FM antenna terminal 75 Ω (unbalanced) D/A converter MULTI BIT
MW tuning range 531 kHz to 1602 kHz Signal-to-noise ratio 90 dB (1 kHz, 0 dB)
AM usable sensitivity 350 µV/m Wow and flutter Unmeasurable
AM antenna Loop antenna
GENERAL
AMPLIFIER Power requirements 230 V AC, 50/60 Hz
Power output Rated: 12 W + 12 W(6 Ω, T.H.D. 1 %, Power consumption 50 W
1 kHz/DIN 45500) Power consumption in standby mode
Reference: 15 W + 15 W(6 Ω, T.H.D. with ECO mode on: 0.2 W
10 %, 1 kHz/DIN 45324) with ECO mode off: 9 W
MUSIC POWER Dimensions (w/h/d) Approx. 163 × 230.5 × 240 mm
30 W + 30 W Mass Approx. 3.5 kg
Input AUX IN: 800 mV
Outputs SPEAKER: 6 Ω or more Supplied accessories: FM antenna (1)
PHONES: 32Ω or more AM antenna (1)
Remote commander (1)
CASSETTE DECK Batteries (2)
Track format 4 tracks, 2 channels stereo
Frequency response 50 Hz – 10000 Hz Specifications and external appearance are subject to change
Recording system AC bias
without notice.
Heads Recording/playback × 1, erase × 1

MICRO HI-FI COMPONENT SYSTEM

9-961-011-02 Sony Corporation
2004I16-1 Personal Audio Company
© 2004.09 Published by Sony Engineering Corporation
CX-LEM400

TABLE OF CONTENTS

1. SERVICING NOTES ······················································· 3

2. GENERAL ·········································································· 5

3. DISASSEMBLY
3-1. REAR CABINET ·························································· 7
3-2. CD CABINET SECTION,
FRONT PANEL SECTION ··········································· 8
3-3. CD MECHANISM DECK ············································ 8
3-4. CONTROL BOARD, SUB CONTROL BOARD ········· 9
3-5. TAPE MECHANISM DECK ········································ 9
3-6. CASSETTE DOOR ASSY ·········································· 10
3-7. POWER BOARD, MAIN BOARD ····························· 10
3-8. BD BOARD, OPTICAL PICK-UP (A-MAX. D) ······· 11

4. MECHANICAL ADJUSTMENTS ····························· 12

5. ELECTRICAL ADJUSTMENTS ······························· 12

6. DIAGRAMS ······································································ 16
6-1. BLOCK DIAGRAM – CD SECTION – ···················· 17
6-2. BLOCK DIAGRAM – MAIN SECTION – ··············· 18
6-3. PRINTED WIRING BOARD – BD SECTION – ······ 19
6-4. SCHEMATIC DIAGRAM – BD SECTION – ··········· 20
6-5. PRINTED WIRING BOARDS
– MAIN SECTION – ················································· 21
6-6. SCHEMATIC DIAGRAM
– MAIN SECTION – ················································· 22
6-7. PRINTED WIRING BOARD
– CONTROL SECTION – ·········································· 23
6-8. SCHEMATIC DIAGRAM
– CONTROL SECTION – ·········································· 24
6-9. PRINTED WIRING BOARD
– POWER SECTION – ·············································· 25
6-10. SCHEMATIC DIAGRAM
– POWER SECTION – ··············································· 25
6-11. IC PIN FUNCTION DESCRIPTION ························· 30

7. EXPLODED VIEWS
7-1. CABINET SECTION ·················································· 32
7-2. FRONT PANEL SECTION ········································· 33
7-3. CD CABINET SECTION ··········································· 34
7-4. BU-30DBD64S ··························································· 35

8. ELECTRICAL PARTS LIST ······································· 36

2
 CX-LEM400
SECTION 1
SERVICING NOTES

Notes on chip component replacement CAUTION

• Never reuse a disconnected chip component. Use of controls or adjustments or performance of procedures
• Notice that the minus side of a tantalum capacitor may be dam- other than those specified herein may result in hazardous
aged by heat. radiation exposure.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the This appliance is classified as a CLASS 1 LASER product.
circuit board (within 3 times). This label is located on the exterior.
• Be careful not to apply force on the conductor when soldering or
unsoldering.

Laser component in this product is capable of emitting radiation

exceeding the limit for Class 1.

NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.

LASER DIODE AND FOCUS SEARCH OPERATION

CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveforms is output three times.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

3
CX-LEM400

Service Position of the CD Mechanism Deck

MAIN board

BD board

Service Position of the Tape Cassette Mechanism Deck

CONTROL board

MAIN board

POWER board

4
 CX-LEM400
SECTION 2
GENERAL This section is extracted
from instruction manual.

PARTS AND CONTROLS

Main unit: front 5 ECD (7-10) Main unit: rear
Starts and pauses CD play.
Refer to the pages indicated in parentheses for details. Refer to the pages indicated in parentheses for details.
4 TUNER/BAND (7, 12)
Selects tuner function and the tuner band.
1 cTAPE (REC MUTING) (7, 16, 17) 1
5 Starts playback.
2 6 2
Also used to enter 4-second blank spaces during
7 3
recording.
8 AUX (7) 4
Selects the function of external equipment connected to
AUX IN jacks.
3 5
6 VOLUME (15, 18)
Adjusts the volume. 1 AM jack and FM 75 Ω terminal (4)
1 POWER 6STANDBY/ON (7)
7 f/r-, +t/g (8, 10, 14-16, 18, Plug in the supplied AM and FM antennas.
Switches the unit on and off (standby).
19) 2 AUX IN jacks
2 ECO (7)
CD: skips to a previous or a succeeding track when Accept analogue sound signals from external equipment.
Sets the ECO mode on or off.
pressed, searches a track in fast forward or reverse Connect external equipment using an optional connecting
SYNCHRO REC (17) playback when held down. cable with RCA phono plugs (red plug to R jack, white
Starts recording and CD play simultaneously. Tape: rewinds or fast forwards the tape. plug to L jack). Refer also to the operating instructions
Tuner: manually tunes up or down within the band. for your equipment.
REC START/PAUSE (17) To switch function to external input, press AUX.
Starts and pauses recording. sSTOP (8-10, 16, 17)
To change a source name in the display of the
CD and tape: stops playback.
RDS (12-14) AUX function.
Tuner: clears a preset station.
Activates RDS features. Hold down AUX and press POWER while the power is
TONE (15) on.
3 PHONES jack Adjusts the bass or treble level.
Plug in optional headphones set with a stereo mini plug AUX VIDEO TV
(ø3.5 mm). Speaker output is cancelled. 8 zPUSH EJECT (16, 17)
Opens or closes the cassette holder. 3 SUB WOOFER jack
4 OPEN (8) Connect optional powered sub woofer with a built-in
Opens or closes the disc compartment. amplifier to the jack.
4 SPEAKER terminals (4)
Connect the speaker cords of the supplied speakers.
5 AC power cord (4)

Remote commander 3 SHUFFLE/PROGRAM (8, 9) 9 CLEAR (9, 12, 19)

Selects shuffle or programmed CD playback mode. CD: Clears a CD program.
Refer to the pages indicated in parentheses for details.
Tuner: Clears a preset station.
REPEAT (8)
1 8 Selects repeat CD playback mode. 0 TREBLE (15)
Adjusts the treble level.
4 ALBUM/PRESETN,M (10, 12)
2 MP3-CD: skips to a previous or succeeding album. BASS (15)
9 Tuner: tunes in a preset station. Adjusts the bass level.

3 0 f/r,t/g (8, 10) ! s (8-10, 16, 17)

4 ENTER (7, 12, 18, 19) @ FUNCTION (17)
! Determines the mode.
5 Switches the active function among TAPE, TUNER, AUX
@ Stores the received station to preset.
6 (VIDEO or TV) and CD.
#
7 5 ECD (7-9) # VOLUME +,- (15)
TUNER/BAND (7, 12)
dTAPE (7, 16)
Buttons with the same or similar names on the main unit Starts playback but cannot change the playback side.
basically have the same function.
AUX (7)
1 POWER (7)
6 DISPLAY (8)
2 1–10/0, >10 (8, 10, 12) Changes the display in CD playback mode.
CD: selects a track of the specified number.
DIMMER (7)
Tuner: tunes in the station with the specified preset
Adjusts the display window brightness.
number.
SLEEP (18)
The numbered buttons take on these functions when pressed with
Selects sleep-timer mode.
SHIFT held down:
7 SHIFT
CLOCK (7)
Hold down when pressing a numbered button to change
Selects clock mode. its function to that printed above the number.
TIMER (18) 8 MUTING (15)
Selects timer mode. To turn off the sound temporarily.
TUNER MODE (15)
Switches between stereo or monaural FM reception.

5
CX-LEM400

ADJUSTMENTS BEFORE OPERATION

POWER ECD, POWER Setting the clock
6STANDBY/ON TUNER/ 1 In stop mode, hold down SHIFT and press CLOCK
BAND, on the remote.
cTAPE, CLOCK Go to step 3 when the hour of the clock display flashes.
ECO AUX
ENTER 2 Within 6 seconds, press ENTER.
f,g ECD, The hour flashes in the display.
TUNER/ f,g 3 Press f or g to set the hour, then press
BAND,
dTAPE,
ENTER.
AUX 4 Press f or g to set the minute.
SHIFT Each press changes the time in 1-minute steps.
DIMMER 5 Press ENTER.
The time display stops flashing and the clock starts from
00 seconds.
Power ECO mode
Turning the unit on Reduces power consumption in standby mode with the following To display the time while the power is on
Press POWER 6STANDBY/ON (POWER on the remote ). operations. Hold down SHIFT and press CLOCK on the remote.
Alternatively, press cTAPE, TUNER/BAND, AUX or ECD. The time will be displayed for 6 seconds.
Press ECO.
Playback will start automatically if a disc or tape is loaded. If "- -:- -" appears when the unit is turned off
Each press of the button changes the mode as follows;
Turning the unit off There has been a power interruption. Reset the clock.
ECO ON: Power economizing mode is activated.
Press POWER 6STANDBY/ON again.
When the unit turns off, everything in the display disappears
The unit goes into standby.
and only the red indicator on POWER lights to show that the
power is being supplied.
Dimmer ECO OFF: Power economizing mode is cancelled.
The display window brightness can be selected. When the unit turns off, the clock display appears.
Press DIMMER on the remote repeatedly. Initial mode is ECO OFF.
Each press of the button changes the following three levels:
"DIMMER 1 ", "DIMMER 2" and "DIMMER 0 ". Standby power consumption
"DIMMER 0 " is the brightest. ECO ON: 0.2 W
ECO OFF: 9 W

6
 CX-LEM400
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.

SET

REAR CABINET

CD CABINET SECTION,
FRONT PANEL SECTION

CD MECHANISM DECK CONTROL BOARD, POWER BOARD , MAIN BOARD

(BU-30DBD64S) SUB-CONTROL BOARD

OPTICAL PICK-UP TAPE MECHANISM DECK

(A-MAX.D) (CMAL5Z220A)

CASSETTE DOOR ASSY

Note: Follow the disassembly procedure in the numerical order given.

3-1. REAR CABINET

1 two screws 2 four screws

(+BVTP3 × 10) (+BVTP3 × 10)
8 cabinet rear
3 screw
(+B3 × 10)

4 two screws
(+BVTP3 × 10)
6 four screws
(+K3 × 5)

5 two screws
(+BVTP3 × 10)

7 four screws
(+K3 × 5)

7
CX-LEM400

3-2. CD CABINET SECTION, FRONT PANEL SECTION

6 CD cabinet section
5 wire (flat type)
(9core) (CN104)

3 connector
(S800)

2 claw
4 wire (flat type) (21core)
(CN103)
qa two screws
(+BVTP3 × 10)
1 claw 7 wire (flat type)
(21core)
(CN303)

qs claw

qd claw
8 wire (flat type)
(19core)
(CN302) 0 screw
qf front panel section 9 connector (+BVTP3 × 10)
(CN301)

3-3. CD MECHANISM DECK

1 two screws
(+PWH2.6 × 10)

3 two insulators (BU-30) 5 CD mechanism deck

2 two screws
(+PWH2.6 × 10)

4 two insulators (BU-30)

8
 CX-LEM400

3-4. CONTROL BOARD, SUB CONTROL BOARD

5 four screws
(+BTP3 × 10) 2 wire (flat type)
(19core) (CN807)

6 CONTROL board

3 two screws
(+BVTP3 × 10)

4 SUB CONTROL board

1 knob volume

3-5. TAPE MECHANISM DECK

1 wire (flat type) (7core) (CN101)

2 four screws
(+BVTP3 × 10)

3 tape mechanism deck

9
CX-LEM400

3-6. CASSETTE DOOR ASSY

2 two claws

3 cassette door assy

1 Open the cassette door assy.

3-7. POWER BOARD, MAIN BOARD

5 screw 3 four screws

(+BVTP3 × 10) (+BVTP4 × 12)
7 MAIN board
2 connector 1 connector
(CN901) (AC IN)
6 screw
(+BVTP3 × 10) 4 POWER board

10
 CX-LEM400

3-8. BD BOARD, OPTICAL PICK-UP (A-MAX. D)

6 optical pick-up(A-MAX.D)

3 wire (flat type) (16 core)

(CN101)

5 BD board

2 Remove two solders.

1 Remove two
solders. 4

11
CX-LEM400
SECTION 4 SECTION 5
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
• TAPE MECHANISM DECK SECTION DECK SECTION 0 dB = 0.775 V
Precaution
1. Clean the following parts with a denatured alcohol-moistened Precaution
swab: 1. Demagnetize the record/playback head with a head demagne-
record/playback heads pinch rollers tizer.
erase head rubber belts 2. Do not use a magnetized screwdriver for the adjustments.
capstan idlers 3. After the adjustments, apply suitable locking compound to the
2. Demagnetize the record/playback head with a head demagne- parts adjust.
tizer. 4. The adjustments should be performed with the rated power
3. Do not use a magnetized screwdriver for the adjustments. supply voltage unless otherwise noted.
4. The adjustments should be performed with the rated power 5. The adjustments should be performed in the order given in
supply voltage unless otherwise noted. this service manual. (As a general rule, playback circuit ad-
justment should be completed before performing recording
Torque Measurement circuit adjustment.)
Mode Torque meter Meter reading
6. The adjustments should be performed for both L-CH and R-
CH.
2.94 mN • m to 7.84 mN • m 7. Switches and controls should be set as follows unless other-
FWD CQ-102C 31 to 71 g • cm wise specified.
(0.43 – 0.98 oz • inch)
0.14 mN • m to 0.59 mN • m • Test Tape
FWD CQ-102C 2 to 6 g • cm
back tension Tape Signal Used for
(0.02 – 0.08 oz • inch) P-4-A100 10 kHz, – 10 dB Azimuth Adjustment
6.86 mN • m to 17.64 mN • m WS-48B 3 kHz, 0 dB Tape Speed Check
FF/REW CQ-201B 71 to 143 g • cm
(0.98 – 1.99 oz • inch)
more than 0.98 N • m
FWD tension CQ-403A 100 g or more
(3.53 oz or more)

12
 CX-LEM400

Record/Playback Head Azimuth Adjustment Adjustment Location: Record/Playback/Erase Head

Procedure:
1. Mode: Playback
test tape MAIN board
P-4-A100 SPEAKER terminal (J302)
(10 kHz, – 10 dB) L-CH, R-CH
level meter

set
+
–

2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.

within
L-CH 1dB
peak
within
Output 1dB adjustment screw
level

R-CH
peak
Screw Screw
position L-CH R-CH position
peak peak
Note: Refer to “3-6. Cassette Door Assy” (see page 10)
3. Mode: Playback
Tape Speed Check
MAIN board Mode: Playback
test tape SPEAKER terminal (J302)
P-4-A100 L-CH test tape
(10 kHz, – 10 dB) oscilloscope WS-48B
(3 kHz, 0 dB) frequency counter
L-CH

V H set +
set –

MAIN board
R-CH SPEAKER terminal (J302)
R-CH L-CH, R-CH

waveform of oscilloscope 1. Insert the WS-48B into the deck.

2. Press the TAPE N button on the deck.
3. Confirm that the frequency counter reads 3,000 ± 90 Hz.
in phase 45 ° 90 ° 135 ° 180 °
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
good wrong
(WS-48B)

4. After the adjustments, apply suitable locking compound to the

parts adjusted.

13
CX-LEM400

RFDC signal waveform

CD SECTION
VOLT/DIV: 200 mV
Note: TIME/DIV: 500 ns
1. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
2. Use an oscilloscope with more than 10MΩ impedance.
3. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks. level: 0.6 ± 0.15 Vp-p

S-curve Check
Connection:

oscilloscope Checking Location: CD board (Conductor side)

BD board
RFAC Level Check
TP (FE) + Connection:
TP (VC) –
oscilloscope

Procedure: BD board
1. Connect an oscilloscope to test point TP (FE) and TP (VC) TP (RFAC) +
on the BD board. TP (VC) –
2. While depressing the CD u button, insert an AC plug.
3. Put the disc (YEDS-18) in and press the STOP x button Procedure:
and actuate the focus search. (actuate the focus search when 1. Connect an oscilloscope to test point TP (RFAC) and TP (VC)
disc table is moving in and out) on the BD board.
4. Check the oscilloscope waveform (S-curve) is symmetrical 2. Turn the power on.
between A and B. And confirm peak to peak level within 2 ± 1 3. Put the disc (YEDS-18) in to playback the number five track.
Vp-p. 4. Confirm that oscilloscope waveform is clear and check RFAC
signal level is correct or not.
S-curve waveform Note: A clear RFAC signal waveform means that the shape “◊” can be
symmetry clearly distinguished at the center of the waveform.

RFAC signal waveform

VOLT/DIV: 200 mV
A TIME/DIV: 500 ns
within 2 ± 1 Vp-p
B

level: 1.0 ± 0.4 Vp-p

Note: • Try to measure several times to make sure than the ratio of A : B
or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.

Checking Location: BD board (Side B) Checking Location: BD board (Side B)

RFDC Level Check

Connection:
oscilloscope
BD board

TP (RFDC) +
TP (VC) –

Procedure:
1. Connect an oscilloscope to test point TP (RFDC) and TP (VC)
on the BD board.
2. Turn the power on.
3. Put the disc (YEDS-18) in to playback the number five track.
4. Confirm that oscilloscope waveform is clear and check RFDC
signal level is correct or not.
Note: A clear RFDC signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.

14
 CX-LEM400

E-F Balance Adjustment Checking Location:

Connection:
– BD BOARD (Side B) –
oscilloscope
BD board

TP (TE) +
TP (VC) –

Procedure:
1. Connect an oscilloscpe to test point TP (TE) and TP (VC) on
the BD board.
2. While depressing the CD u button, insert an AC plug to
enter the CD test mode.
IC101
3. Put the disc (YEDS-18) in to playback the number five track.
4. Press the CD u button. If it plays, press the CD u button
again. (The tracking servo and the sledding servo are
turned OFF) RV101 TP2
5. Check the level B of the oscilliscope's waveform and the A E-F Balance (TE) TP6
(DC voltage) of the center of the Traverse waveform. Adjustment (RFDC)
TP8
Confirm the following : (RFAC)
TP7
A/B x 100 = less than ± 10% (VC) TP4
(FE)
IC103
Traverse Waveform
Center of
the waveform

B
A (DC
0V
voltage)

level: 1.0 ± 0.5 Vp-p

6. Press the CD u button. (The tracking servo and sledding

servo are turned ON)
Rotate RV101 on BD board and adjust the C (DC voltage)
is almost equal to the A (DC voltage) in step 4.
7. To exit from this mode, turn the power off.
Notes: • Always move the optical pick-up to most inside track when
exiting from this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can
be chipped.

Traverse Waveform

0V C (DC
voltage)

Tracking servo Tracking servo

Sled servo Sled servo
OFF ON

Checking Location: BD board (Side B)

15
CX-LEM400
SECTION 6
DIAGRAMS
• Circuit Boards Location

MAIN board
BD board

CONTROL board

SUB-CONTROL board POWER board

REGULATOR board

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)

For schematic diagrams. For printed wiring boards.

Note: Note:
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
and tantalums. • f : internal component.
• All resistors are in Ω and 1/4 W or less unless otherwise • : Pattern from the side which enables seeing.
specified.
• f : internal component.
• 2 : nonflammable resistor.
• 1 : fusible resistor.
• C : panel designation.

Note: The components identified by mark 0 or dotted line

with mark 0 are critical for safety.
Replace only with part number specified.

• A : B+ Line.
• B : B– Line.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : TUNER
J : CD
d : AUX
E : PB (TAPE)
a : REC (TAPE)

16
 CX-LEM400
6-1. BLOCK DIAGRAM – CD SECTION –

OPTICAL PICK-UP IC101

BLOCK IC103 DIGITAL SERVO
RF AMP DIGITAL SIGNAL PROC.
VC
2 27 VC RF AC 15 50 RFAC
VCC
4 +3.3V
6 A RFDC 28 43 RFDC IC104
7 B RFDCI 29 D/A CONV,
PD1 MP3 DECODER
7 8 C
PD2 LOUT
5 9 D FE 16 39 FE PCMD 66 12 SDIO LO 23 LOUT
I5-10
3 10 E FEI 17 BCLK 67 13 BCKIA L-CH
I1-6
1 11 F 41 TE LRCK 65 14 LRCKIA
Q101
TE 18 40 SE XTAI 71 A MAIN SECTION
LD LD
1 LD
DRIVE
XTAO 72
X201 ROUT
AVDD(3.3V) 16.9344MHz RO 26 ROUT
GND
RV101 R-CH
19 TE_BAL SW 12
IC804 (1/5) IC801 (1/2)
PD LEVEL SHIFT SYSTEM CONTROLLER
2 PD 62 XI
VR 4 16
71 MIDIO2
IC102 63 XO
MOTOR/COIL DRIVE MIDIO 5 73 MIDIO1
F+
52 VO1+ IN1+ 35 33 FFDR
FOCUS MICK 6 79 MICK
COIL F- IC804 (2/5)
47 VO1- IN1- 34 34 FRDR 3 17
MIACK 7 69 MIACK
T+ RESET 1 76 MP3RST
56 VO2+ IN2+ 32 31 TFDR
TRACKING MICS 3 81 MICS
COIL T-
55 VO2- IN2- 31 32 TRDR REQ 39 83 MP3REQ
MILP 4 96 MILP

M102 2 VO3+ IN3+ 27 29 SFDR

(SLED) M
1 VO3- IN3- 26 30 SRDR DATA 4 87 DATA
CLOK 6 97 CLK
M101 10 VO4+ IN4R 24 25 MDP XLAT 5 86 XLT
(SPINDLE) M SQCK 77 88 SQCK
5 VO4- SCLK 8 IC804 (3/5)
STBY 2 18
8 SCOR 15 3 SCOR
IC804 (4/5)
6 14
SQSO 76 91 SUBQ
IC804 (5/5)
5 15
SENS 7 94 SENS

XRST 2

95 RFSW

85 XRST
IC805
D/A CONV.

PWM3 TU DO
3 PWM3 DATA 6
PWM2
2 PWM2 CLK 7
TU CLK B MAIN SECTION
PWM1
1 PWM1 LD 8 1 LD
IC121
• Signal Path

: CD +2.5V
+2.5V 3 1 DVDD (3.3V) S800
REG 68 C-DOOR
(OPEN/CLOSE)

17 17
CX-LEM400
6-2. BLOCK DIAGRAM – MAIN SECTION –

IC302
J303(1/2) SOUND PROCESSOR IC303
R-CH
POWER J301
L 19 AUX-L OUT-L 18 1 11
AMP PHONES
AUX IN IC801 (2/2) 13
23 TU-L OUT-R 16 R-CH
R R-CH SYSTEM CONTROLLER 4
2 TA-L
CONT 13 10 F-DATA
21 CD-L AMP-STNBY 78
RECO-L 28
TUNER PACK L
FL801
+5V J302
+5V FLUORESCENT FL -26V SPEAKER
INDICATOR TUBE
L-CH TU DO
R-CH R-CH CD SECTION B TU CLK
45
R-CH R
. F1 F2
TU-DI 98 TU DATA 47
SEG1
TU-DO 99 TU COUNT 50
SEG20 .
TU-CL 100 TU CLK 52 J303(2/2)
CE 84 TU CE 66 SUB
TUNED WOOFER
93 TU TUNED
G1 37
STEREO 92 TU STEREO
G8 44
MUTE 80 TU MUTE
S801-806
FM-SIGNAL 23 FM-SIGNAL
RDS-DATA FUCTION
7 RDS-DATA KEY1 18
KEY
RDS-CLK 27 RDS-CLK
S807-813
FUCTION
KEY2 19
DECK KEY
RV801
VOL
L-CH VOL.ENC 22 • R-CH is omitted due to same as L-CH.
ENCODER
• Signal Path
REC/PB Q326-332
HEAD D811
REC/PB : TUNER
77 TA REC/PB
SWITCH ECO
R-CH R-CH
ECO.LED 75 : CD
12 32.768kHz
T301 X801
BIAS OSC 32.768kHz
: AUX
BIAS 13 32.768kHz
ERASE
HEAD OSC
Q307 : PB (TAPE)
15 8.64MHz
X802
Q308 8.64MHz
+9V : REC (TAPE)
16 8.64MHz-EXTAL
IC802
25 SFT-CLK REMOTE
RMC 29 1 CONTROL 3
Q309 74 TA BIAS RECEIVER
MECHANISM BLOCK D809 +9V
IC801 VDD3 +5.6V (SUB)
PLAY 67 TA PLAY.SW D810 Q310
IC801 VDD1,VDD2
PACK 24 TA SW +5V
TU +5V
REG
Q815 IC803
T END 5 TA END D813
Q323,325 RESET Q305
M1 RST 11 3 RESET 1
MOTOR SWITCH IC302 +5V
DECK M 6 TA MOTOR +5V REG
MOTOR DRIVER
T902
I POWER DOWN 20 POWER AMP POWER
Q321,322 Q339
D322 VCC TRANSFORMER
SOLENOID +5V +5V D916-919 (MAIN)
SOLENOID 4 TA SOL (MAIN) REG IC305
DRIVER D319-321
+10V
TU +10V 3 1
REG

Q338 Q333
D920 D921
POWER AC
I POWER MONITOR 26 MONITER DET D911-914
Q306
IC302 -5V
-5V REG
LOUT
CD SECTION A ROUT R-CH D922-925
Q334-337
FL -26V
Q317 FL -26V
RF VDD REG
(3.3V), +3.3V
CD-VM REG Q319
D312,313
(3.3V) B+ F1(AC 3.5V)
CD-VM(7V) SWITCH
Q320 F2(AC 3.5V)
CD POWER Q311 RY901
CD 82 D317
CONTROL
RELAY
Q315 DRIVE

POWER T901
POWER ON 8 CONTROL POWER
TRANSFORMER
D907-910 (SUB)
Q312-314
+5.6V AC
+5.6V( SUB)
REG IN

18 18
 CX-LEM400
6-3. PRINTED WIRING BOARD – BD SECTION –

1 2 3 4 5 6 7

• Semiconductor
Location
Ref. No. Location
IC101 B-6
IC102 C-6
IC103 C-5

B IC104
IC121
B-5
C-5

Q101 C-3
IC104
IC101

IC121
E
TO
MAIN TP2(TE)

C BOARD
CN306
(Page 21)

TP8(RFAC)
TP6(RFDC)
F
TP4(FE)
TO
CONTROL
TP7(VC)

E
IC102 BOARD
CN803
(Page 23)

IC103

D (A-MAX.D)

19 19
CX-LEM400
6-4. SCHEMATIC DIAGRAM – BD SECTION –

C203
1000p

R216 TP9 C269

1M 47 4V
CKO
FB102 C256 0.1
0

R251 220
C257 0.33
C263 C259 C270 220p
47 4V 0.1 C255
C249 0.1
0.1

R250 220
FB104
0

C271 0.01

C274 0.01
R275 10k

R272 4.7k
R271
10k

R279 100

R255 100
R257 100

R276 100
R259 100 C292
0.1

C266 IC104
0.1 TC94A20F-CX4

0
FB291
C250
0.1
R111 150k
C116 0.1 B

TP5
RFACI

C213 3300p

C107 R120 TP8

R104 RFAC
15k 33p 120k
TP2 TE R102 15k C112 0.1 CN101
R105 1k
16P
R126 47k
R103 C109 0.1
100k

R313 0
R125 47k
C313

0.1 B

CXA2647N
C215

3300p
0.1

C104

C102
0.47 C310 R116 C118 C119
B 0.1 33k 1 1

R117

R115
C230 C216 RV101

C103

C101
470p

470p
C226

33k
C212 390k
47 4V 0.1 1500p 0.01 47k
C224 R114

IC103
1 390k
R308 C211

R203 100k
R204 3.3k
0 0.1

R202 10k

R201 33k
TP6
CN104 R303 RFDC
R206

C209 100p
0

R207 1M
11P R101 C114

R205 1k
4.7k R113
0 2.2k 1000p
C110
0.1 B (A-MAX.D)
C253 Q101
R261 R260 0.1 2SB970
0.1 1k C115
100 10V
FB103 0 C113

R199
TP7 R122

0
VC 100 R123
R266 100k
C111 C108 10V
E C261
220
4V
C251
0.1 C264
47
R265 220
220
C265
47
4V
47 4V 0.1
3.3

C117 R118
R351 0 4V 10k
TO FB203 0.1 R133 2.2k
0 TP3 SE
MAIN
C268 R132 330k
BOARD FB351 0 C267 4700p 4700p
R131 68k
CN306
TP4 FE C133 M102
(Page 22) 2.2 C131
R230 150 0.068
R231 330 C132 0.022
R232 330
R233 330

C227
0.1 M101
C121 0 R310 0 R166 0
C316 0.1
R168 0
R291 0 X201 16.9344MHz R167 0
R252
C254 22p R169 0
1M IC101
FB204 CXD3068Q C222
C258 22p R253
0 1k 0.1
R219
R249 560 1k
FB201

C151
0

0.1
IC121
BA25BCOFP-E2
C122 0.1
F
TO
CONTROL R309
0
BOARD R221 100
R311
L101 C231 C260
CN803 R222 100
C314 0
1000 100
1 6.3V
(Page 24) 6.3V
R220 1k
R223 100 IC102 AN41020A
C229 C208
0.1 0.1 R318 0
R224 100
R225 100
C273 220p

C205
R218 1k

R226 100 0.1

C202
R227 100
0.1
CN102
23P
R316 R321
0 0
R319
C152 R155 C153
0 0.1 0.1
0
R314 0
TP1
SP

L163
R151
C156 0
100k 0.01
FB161
BLM21P331 C150 C169
220 10V 220 10V
R152 2.2k

20 20
 CX-LEM400
6-5. PRINTED WIRING BOARDS – MAIN SECTION –

1 2 3 4 5 6 7 8 9 10

A TO
CONTROL
BOARD
(Page 23)

TUNER
PACK

• Semiconductor
TO Location
BD
E BOARD Ref. No. Location
CN104

C (Page 19) D301

D303
E-7
B-8
D304 C-6
L D305 E-5
TO D306 F-5
CONTROL
AUX IN BOARD D310 E-6
(Page 23) D311 B-5
R D312 B-7
IC302
D313 B-7
D D317
D318
E-6
E-7
SUB D319 G-6
WOOFER
D320 G-5
D321 G-5
D322 G-5

IC302 D-5
IC303 F-4
E +
Q305 E-5
L
Q306 F-5
Q307 D-6
- Q308 D-6
Q309 D-6
IMPEDANCE SPEAKER
USE6-16 IC303 Q310 B-5
Q311 E-6
-
Q312 E-6
Q313 E-6
F R + Q314 E-6
Q315 E-6
Q317 B-8
IC305 Q319 B-7
TO
POWER
Q320 B-7
BOARD Q321 B-6
CN901
(Page 25)
Q322 B-6
Q323 B-6
Q325 B-6
G PHONES
Q326 D-5
Q327 D-5
Q328 C-5
Q329 C-5
Q330 C-5
Q331 C-6
Q333 E-6
Q334 E-7
Q335 F-7
H Q336 F-7
Q337 F-7
Q338 E-7
Q339 C-6
Q340 E-4
Q341 E-4

21 21
CX-LEM400
6-6. SCHEMATIC DIAGRAM – MAIN SECTION –

J303
3P

R225 22k
R236

470p
C227
R237
C226
220p
10k R125 22k

4.7k
R226 22k
C126 R137 C127
220p 4.7k 470p R126 22k IC303 LA4628

C111 5600p

C211 5600p
C112 3300p

C212 3300p

C216 470pF
C116 470pF
0.22 50V C217 1200p

C117 1200p
R136

R215 3.3k
R115 3.3k
10k C342
470 16V

R347
1k

R223
0.47 50V 2.2k
R121 1.5k C113

R123
0.47 50V 2.2k
R242 R142
22k 22k

R113
C109

C209

R114

R214
470p

470p

R213
C231

1.8k

1.8k
1k

1k

R219 1.5k

R119 1.5k
N.M

R221 1.5k

C214
R217 1k

R117 1k
C133 R143

50V
0.22 50V
C114
C130

16V
R112 R212 12k C230

50V
50V
10V
C213
33k 33k 10 50V 10 50V

R240 2.2k

R140 2.2k
R229 2.2
R230 2.2
R208 8.2k

R211
R111

R129 2.2

R130 2.2
CN301

2.2k
R209 2.2k
R109 2.2k

7P 2.2k R122 C115 R124

C121
C221

C120
C220
R108 8.2k 4.7 50V 15k C123 J302
68k

C119

C353
C310
SP TERMINAL

R218 4.7k

R118 4.7k
R216 8.2k

R116 8.2k

C219
R120 10k
16V

R220 10k

C352
C131 C110 C210 R222 R132 1k R232 4P
N.M 180p 180p 68k 1k L101
L102
C233 C350
C215 R224 L202
4.7 50V 15k AXIAL

R231 2.2k
R131 C223 L201

C134 2200p
2.2k

C322 0.01
R228 1k
R243 16V

R239
R139
R128 C234 R238

180

180
12k 1k 2200p 180

R138
C351

180
220p C118
N.M 0.033
IC302 J301
BD3881FV H/P JACK

22 50V
C128
C218
0.033 C228 C129 C229
C311 22 50V 22 50V 22 50V
R358
1k
R306
10k CN307 CNP308 IC305
50V

50V
R205

KIA7809PI
390k

3300p

3300p
C103
C108

C208

R301
C107

C207

10k
100p C203 Q305 D322
100p KTC3203Y-AT Q306 1N4002
R103 470 KTA1271Y-AT

1000 16V
R302 R352
470 D319 D320 D321

C309
R203 470 4.7k

4700 25V
R105 C106 1N4002B1N4002B1N4002B

C323
390k 0.022
C202 1000p

1SS133T-77
R106 R107 150k CN305
C102 1000p

C303
0.01
R102 39k

R202 39k

5.6k 10P

D317
R304

C304
R206 C206

0.01
470

R305
MTZJ-T-77-5.1A

MTZJ-T-77-5.1A
R104 5.6k 0.022

470
82 R204 C333
82 R207 150k D305

D306
22 25V

470 16V

220 10V
C302

C305
C104 C204
C301

R303

10V 10V
10p

4.7k

Q330
2SK2158-T2B
C355 C344 Q311
C343 25 C356
25 KTA1271Y-AT 25
C313
100 16V

Q338 Q314 R326

KTA1271Y-AT

MTZJ-T-77-5.6B
C312 KRC402-RTK 100k
220p R325
R324 100k R327

D310
Q331 R351 R336 R321 2.2k 10k
Q329 KRA303-RTK 10k 4.7k 100k C326
R323 2200p
2SK2158-T2B B

220 16V
1k R349

C324
R319 1M R315 JR
2.2k
D302
1SS133T-77 Q333
C336 KRC402-RTK R322
Q332 22 50V 1k Q312 Q313
Q328 KRA303-RTK KTC3203YAT KTC3203YAT
2SK2158-T2B R320
4.7k D301 R350 Q315
1SS133 10k KRC402-RTK
Q319
Q327 KTA1273Y-AT
KTA1504
C101 C201 Q323
1000p 1000p KYA1271Y-AT
Q326 D312 D313 R317
KTA1504 Q339 Q317 1N4002B 1N4002B 47k
KTC3203Y-AT KTC3205Y-AT Q310
R331
R101 R201 Q308 Q321 47k KTC3205Y-AT
5.6k 5.6k KTA1271Y-AT R348 Q320 KTA1271Y-AT R330 R353
1k KRC402-RTK 47k 4.7
R328
R329 1k
R332 R318 1k R316
R309 R313 1k 220 Q322 470
T301 4.7 KRC402-RTK

47 25V
C318 47k C345

C327
BAIS OSC
16

100 16V
10V
100 16
220 10

C347
C329

C319
C332
C331

C328

C320
Q307 R312 C335
C330

0.01

0.01
R314 KTC3205Y-AT 4.7k 0.01 0.01
5.6k
Q309
KRC402-RTK Q325 D311
C317 D304 D303 KRC402-RTK MTZJ-T-77-5.6B
1000pF MTZJ-T-77-5.6B MTZJ-T-77-3.9B
C314
0.012

C315 R343 R344

47 25V R311 3.3 1/8 3.3 1/8
22k C316
6800p R345 R346
3.3 1/8 3.3 1/8
R310 C349 Q336 Q337
3.3 22 25V R338 Q335 KTA1266GR-AT KTA1266GR-AT
10 1/8 KTA1266GR-AT
C232 4.7 50V
C132 4.7 50V

R339 R340
4.7k
R357 47k
R356 47k

4.7k

50V

C340 0.1

C341 0.1
R354 R355

R337 100k
10k 100k Q334 R341 R342

C339 0.01
KTA1266GR-AT 4.7k 4.7k

C337
C338 10V
D318
MTZJ-T-77-27B

CN306 CN303 CN304

11P CN302 19P 15P
15P

20 24 24

22 22
 CX-LEM400
6-7. PRINTED WIRING BOARD – CONTROL SECTION –

1 2 3 4 5 6 7 8 9 10

FLUORESCENT INDICATOR TUBE

IC802
B IC801 POWER
STANDBY/ON

RED
S800
(OPEN) BLACK

ECO

C TO
MAIN
CD
BOARD
CN303
TAPE SYNCHRO
REC (Page 21)
AUX (REC MUTING) TUNER/BAND

• Semiconductor
STOP Location
REC START/
D PAUSE Ref. No. Location
TONE D803 C-8
D807 E-7
D808 E-6
D809 D-6
RDS D810 D-8
D811 B-9
IC803 D812 D-6
D813 D-7
E
IC804 TO IC801 B-6
F MAIN IC802 B-4
TO TAPE MECHANISM BOARD
BD DECK CN302
IC803 E-6
BOARD (Page 21)
CN102 Q815 E-6
(Page 19)
IC805

23 23
CX-LEM400
6-8. SCHEMATIC DIAGRAM – CONTROL SECTION –

FL801
HNA-08SS49T
D811
SLR-342VRT32

CNP804 R820 R892

100k 1k
R883
S800 2.2k

50V
C810
C835

RP05 100K
RP04 100K
RP03 100K
RP02 100K
RP01 100K
RG08 100K
RG07 100K

RG06 100K
RG05 100K
RG04 100K
RG03 100K
RG02 100K
RG01 100K
R882

RP19 100K
RP20 100K

RP18 100K
RP17 100K
RP16 100K
RP15 100K
RP14 100K
RP13 100K
RP12 100K
RP11 100K
RP10 100K
RP09 100K
RP08 100K
RP07 100K
RP06 100K
10k 50V

R713 1.8k
R714 1.8k

R716 1.8k
R717 1.8k
R715 2.7k
CNP803 C811
23P 50V
F

R821 10k
C807
0.01 50V F
R706 100
C812

R894 10k
R701 1k
R858 1k
R857 1k
R897 1k
R884 1k
R874 1k

R873 1k

R819 1k
R870 1k
6.3V

R872 1k
R703 100

R869 1k
R899 100
R898 100 R893 100k
R880 C834
R891 100k 10k 50V
R890 100k
R889 100k
R888 100k
R887 100k R881
2.2k
R702 1k R886 100k
R895 1k
20
R885 100k R704 1k C809 CNP802
R822 1k 0.01 19P
50V
R823 1k F

R824 1k
R825 1k
C808
R826 1k
6.3V

C813
0.01
C814
C837 1000p

6.3V
100
IC801
R832 1k LC87680B-52C5-E
R828 1k

C843
R829 1k
R830 1k R831 1k
B
100p

R705 1k
R833 1k

R834 1k 22

R835 1k
R836 1k

R839 10k
R846 R845 R844 R843 R842 R841 R840
10k 470 4.7k 1k 2.2k 2.2k 2.2k

S801 R818 56k

C836 18p CH
S804 S803 S802

R809 47k

R811 22k
R803 1k
R804 1k
R805 1k
R806 1k
R827 1k

R812 1k
R813 1k
S806 S805 R810
10M
X802

R814 390k
IC802

R815 220k
8.64MHz NJL64H380A

R816 1k
32.768KHz
X801

C817 20p 50V CH

20p 50V CH
R871 R854 R853 R852 R851 R850 R849 R848 R847
470 4.7k 1k 2.2k

C816
22k 10k 2.2k 2.2k 10k

C801 24p 50V CH

B
24p 50V CH
S807

R808 1k
R807 1k
S813 S812 S811 S810

R896 47k
C805

C802
S809 S808 C803 22 16V
0.01
50V
F

C815
C806

R859
C804 0.01

100
JW821 50V
BEAD 100
6.3V F

C841 C842

R860 47k
R861 47k
1SS355TE-17
R863 CNP801
R865 10k

D809
R867 R856 RV801
47k 10k 10k
D810 R862 N.M
1SS133T-77
CNP806 R864 10k
19P
R866 C820 R855
10k 22k C821
C839 R879 R876 R875 D812 1SS355TE-17
22k 1k D807 1k 50V
1SS355TE-17 F 50V
F
Q815 D813 1SS355TE-17
CNP807 KTC3875 IC803
19P PST592C-T

22 16V
C831 C828

C822
0.1 B 470 6.3V

R877
R878 47k C829

1SS133T-77
47k C830 47 25V

D803
0.1 B
R710 R711
1k 1k R712
1k D808
1SS355TE-17

R718 R719 R720

BH2220FMV-TR

1.8k 1.8k 1.8k

IC805

C832
IC804
TC74HCT245AF (EL)
C840

R709 68k JW803 CNP805

15P
R708 150k JW802
R707 2.7k JW801

C
22

24 24
 CX-LEM400
6-9. PRINTED WIRING BOARD – POWER SECTION – 6-10. SCHEMATIC DIAGRAM – POWER SECTION –

1 2 3 4 5 6 7

1N5401
D916
C907 D918 C905
0.022 1N5401 0.022

1N5401
D917
C908 D919 C906
0.022 1N5401 0.022

D920 R901
1SS133 47k

D921 R902
1SS133 47k T902

1N4002
D911
C910 D913 C909
0.022 1N4002 0.022

AC D914

1N4002
C912

D912
0.022 1N4002 C911
0.022
IN

R903

1N4002B
JUMPER

D925

C915
0.022
C913 D923
0.022 1N4002B

1N4002B
D922
C914 D924 C916
0.022 1N4002B 0.022

R907
100
TO CN901
10P
MAIN
BOARD
CNP305
(Page 21)
T901
POWER
TRANSFORMER
(SUB) RY901

D D906
1SS133T-77

22

1N4002B
LF901

D909
D907 AC IN
C346 1N4002B CN902
16 2P

1N4002B
T901

D910
D908
1N4002B

E T902
POWER
TRANSFORMER
(MAIN)

• Semiconductor
Location
Ref. No. Location
D906 C-3
D907 C-3
D908 C-3
D909 A-3
D910 B-3
D911 C-4
D912 C-3
D913 C-3
D914 C-3
D916 B-2
D917 B-2
D918 B-2
D919 B-2
D920 B-2
D921 B-2
D922 D-3
D923 D-3
D924 D-3
D925 D-3

25 25
CX-LEM400

• Waveforms • IC Block Diagrams

– BD Board – – CONTROL Board – – MAIN Board – – CD Board –

1 TP8 (RFAC) 3 IC801 qh (8.64MHz- 5 Q307 Collector IC101 CXD3017Q

EXTAL)

AVDD3

AVDD0
AVSS3

AVSS0
DOUT

ASYO

RFDC
RFAC
CLTV

ADIO
IGEN
ASYI
BIAS
FILO
VDD

PCO
VSS

FILI

CE
TE
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

1.2Vp-p 115ns 8.4Vp-p

4.0Vp-p 12 µs 40 SE
ERROR
200mV/DIV, 1 µs/DIV 1V/DIV, 40ns/DIV 2V/DIV, 4 µs/DIV DIGITAL CORRECTOR
39 FE
DIGITAL ASYMMETRY 38 VC

INTERNAL BUS
OUT
PLL CORRECTOR
2 IC101 us (XTAO) 4 IC801 qd (32.768kHz) 16K
RAM OPERATIONAL
LRCK 61 AMPLIFIER
D/A EFM ANALOG SWITCH
PCMD 62
INTERFACE DEMODULATOR
BCK 63 A/D
CONVERTER
3.3Vp-p 5.3Vp-p EMPH 64
59.1ns (16.9MHz) 30.5 µs XVDD 65
1V/DIV, 40ns/DIV 1V/DIV, 10 µs/DIV
XTAI 66 TIMING
XTAO 67 LOGIC CLOCK
37 XTSL
XVSS 68 GENERATOR
36 TES1
AVDD1 69 35 TEST
AOUT1 70 SERVO DSP PWM GENERATOR 34 VSS
AIN1 71
FOCUS FOCUS PWM 33 FRDR
SERVO GENERATOR 32 FFDR
TRACKING TRACKING 31 TRDR
LOUT1 72 SERVO PWM GENERATOR 30 TFDR
PWM PWM SUBCODE SLED SLED PWM 29 SRDR
AVSS1 73 PROCESSOR SERVO GENERATOR 28 SFDR
AVSS2 74
LOUT2 75 3rd ORDER 27 SSTP
NOISE SHAPER SERVO
INTERFACE 26 MDP
DIGITAL
CLV 25 LOCK
AIN2 76 OVER SAMPLING
DIGITAL FILTER
AOUT2 77 SERVO AUTO MIRR, DFCT, 24 FOK
AVDD2 78 SEQUENCER FOK 23 DFCT
RMUT 79 DETECTOR 22 MIRR
SERIAL IN
LMUT 80 INTERFACE

CPU
INTERFACE 21 COUT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

GFS
SCLK

XLON

SCOR
XLAT

SENS

SPOB

C2PO
XRST
SYSM

WFCK
VDD
SQSO

ATSK

XUGF
SPOA

XPCK
SQCK

CLOK
DATA
IC102 BA5974FP-E2

CH3OUTR

CH4OUTR
CH3OUTF

CH4OUTF
POWVCC
CAPAIN3
CH4SIN'
PRFVCC

CH3RIN
CH4BIN

CH4SIN

CH3FIN

MUTE
GND
28 27 26 25 24 23 22 21 20 19 18 17 16 15

F R
R MUTE
INTERFACE

F
LEVEL SHIFT

THERMAL
SHUTDOWN
F
INTERFACE

F R F
R

INTERFACE
R
F R

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VREFOUT

CH1FIN

CH1RIN

CAPAIN1

CH2FIN

CH2RIN

CAPAIN2

GND

VREFIN

POWVCC

CH2OUTR

CH2OUTF

CH1OUTR

CH1OUTF
26 26
 CX-LEM400

– BD Board –

IC103 CXA2581N-T4

RW/ROM

30 DC OFST
29 RFDCI
A –
–
B +
+ 28 RFDCO
C
DVC
D DVC
VCC
VC
DVC –
RW/ROM
+ VOFST 27 VC
VC

VC
LD 1 26 RFC
EQ 25 VFC
PD 2 APC AMP 24 BST

EQ ON/OFF
RFAC
EQ IN 3 23 RFG
RW/ROM VCA

RFAC VCC 22 VCC

AC SUM 4 SUMMING
AMP B VOFST 21 CEI
C –
–
GND 5 A +
+ 20 CE
D
A B C D
A DVC
A 6
B VC
B 7
C
C 8 RW/ROM
D
D 9 19 TE BAL
RW/ROM

E 10 GM
–
+ 18 TE

F 11 GM

VC
APC-OFF
(Hi-Z) RW/ROM
SW 12
RW/ROM RW/ROM
(H/L)
DVCC 13

B
VOFST 17 FEI
DVC
D –
–
DVC 14 A +
+ 16 FE
C
DVC
VC

RW/ROM
RFAC 15

27
28
PREDRIVER POWER

1
IN1 + LOAD SHORT
IN
– PREDRIVER PROTECTOR

REC-O_L
CX-LEM400

– MAIN Board –

POWER

2
FILTER
TAPE-L

FILTER
RIPPLE
TAPE-R

BIAS

3
PREGND CIRCUIT OVER VOLTAGE/
SURGE
VCC

4
STBY STANDBY
SW THERMAL
SHUT DOWN REC-O_R
CIRCUIT

5
MUTE

CIRCUIT
POP NOISE
TUNER-R

PREVENTION
IN2
TUNER-L

6
IN2 + IN PREDRIVER POWER LOAD SHORT
– PROTECTOR
CD-R

PREDRIVER POWER CD-L

7
POP

IC303 LA4628
OUTPUT PIN TO VCC
IC302 BD3881FV

SHORT PROTECTOR AUX-R

8
+OUT2
AUX-L

OUT-L
TON_H-L

9
-OUT2

OUTPUT PIN TO GND TON_L-L

SHORT PROTECTOR

10
PWR-GND2 TON_H-R

GND2
POWER
OUTPUT PIN TO GND OUT-R
SHORT PROTECTOR

11
+OUT1 TON_L-R

12
PWR-GND1

GND1
VSS

POWER

13
-OUT1

OUTPUT PIN TO VCC

14
VCC SHORT PROTECTOR
 10
GND

11
B8

9
A8

12
B7 8 A7

13
B6
7

A6

14
B5
6

A5

15
B4
– SUB CONTROL Board –

A4

16
B3
4

17 A3
B2
3

A2
18

B1
2

A1
IC804 TC74HC245AF (EL)

19

G
1

DIR
20

VCC

R-2R 8bitREG
1
8

AO1 DAC + LD
DEC
VCC
VCC
VCC

R-2R 8bitREG Serial

2
7

AO2 DAC + Interface CLK

DEC

R-2R 8bitREG
3
6

AO3 DAC + DI
DEC

GND
5

VCC
IC805 BH2220FVM-TR

Power on reset

29
CX-LEM400
CX-LEM400

6-11. IC PIN FUNCTION DESCRIPTION

• IC801 LC876780B-52C5-E (SYSTEM CONTROLLER)

Pin No. Pin Name I/O Description

1 LD O Serial data load signal output to the D/A converter (IC805)
2 NC — Not used (open)
3 SCOR I SCOR (SUBQ request) signal input from the DSP (IC101)
4 TA SOL O Solenoid control signal output to the tape deck
5 TA END I Tape deck reel switch signal input
6 TA MOTOR O Motor control signal output to the tape deck
7 RDS-DATA I RDS data input from the tuner
8 POWER ON O Power relay control signal output
9 AMP-MUTE O Not used
10 F-DATA O Control signal output to the sound processor
11 RST I Reset signal input from the reset IC (IC803)
12 32.768kHz I Resonator terminal (32.768kHz)
13 32.768kHz O Resonator terminal (32.768kHz)
14 GND — Ground terminal
15 8.64MHz I Resonator terminal (8.64MHz)
16 8.64MHz-EXTAL O Resonator terminal (8.64MHz)
17 VDD1 — Power supply terminal
18 KEY1 I Key AD input 1
19 KEY2 I Key AD input 2
20 I POWER DOWN I Power down detection signal input
21 VERSION I Version setting terminal
22 VOL-ENC I Encoder signal input from the volume encoder
23 FM-SIGNAL I RDS signal level input from the tuner
24 TA SW I Tape PACK switch status signal input from the tape deck
25 SHT-CLK O Clock shift control signal output
26 I POWER MONITOR I AC detection signal input
27 RDS-CLK I RDS clock input from the tuner
28 NC — Not used (open)
29 RMC I Remote sensor signal input
30 to 36 NC — Not used (open)
37 to 44 G1 to G8 O Grid signal output to the fluorescent indicator tube
45 SEG1 O Segment signal output to the fluorescent indicator tube
46 VDD3 — Power supply terminal
47 to 50 SEG2 to SEG5 O Segment signal output to the fluorescent indicator tube
51 NO-USE — Ground terminal
52 to 66 SEG6 to SEG20 O Segment signal output to the fluorescent indicator tube
67 TA PLAY.SW I Play switch signal input from the tape deck
68 C-DOOR I CD door open/close switch signal input
69 MIACK I Acknowledge signal input from the MP3 decoder (IC104)
70 BASS+2 O Not used (fixed at “H”)
71 MIDIO2 I Data input from the MP3 decoder (IC104)
72 VDD3 O Power supply terminal
73 MIDIO1 O Data output to the MP3 decoder (IC104)
74 TA BIAS O Bias control signal output to the bias oscillation circuit
75 ECO.LED O ECO LED control signal output
76 MP3RST O Reset signal output to the MP3 decoder (IC104)
77 TA REC/PB O REC/PLAY control signal output to the REC/PLAY switch circuit
78 AMP-STNBY O Standby control signal output to the power amplifier
79 MICK O Clock output to the MP3 decoder (IC104)
80 TU MUTE O Muting signal output to the tuner

30
 CX-LEM400

Pin No. Pin Name I/O Description

81 MICS O Chip select signal output to the MP3 decoder (IC104)
82 CD O CD power supply control signal output
83 MP3REQ I Request signal input from the MP3 decoder (IC104)
84 TU CE O Tuner chip enable signal output to the tuner
85 XRST O Reset signal output to the DSP (IC101)
86 XLT O Latch signal output to the DSP (IC101)
87 DATA O Data output to the DSP (IC101)
88 SQCK O SUBQ clock output to the DSP (IC101)
89 GND — Ground terminal
90 VDD2 — Power supply terminal
91 SUBQ I SUB-Q data input from the DSP (IC101)
92 TU STEREO I Stereo/mono detection signal input from the tuner
93 TU TUNED I Tuner tuned status signal input
94 SENS I SENS signal input from the DSP (IC101)
95 RFSW O LD ON signal output to the RF amplifier (IC103)
96 MILP O Latch pulse output to the MP3 decoder (IC104)
97 CLK O Clock output to the DSP (IC101)
98 TU DATA O Seial data output to the tuner and the D/A converter (IC805)
99 TU COUNT I IF count signal input from the tuner
100 TU CLK O Serial clock output to the tuner and the D/A converter (IC805)

31
CX-LEM400
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number
The components identified by mark 0 or
have some differences from the original one. in the exploded views are not supplied.
dotted line with mark 0 are critical for safety.
• Items marked “*” are not stocked since they Replace only with part number specified.
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
7-1. CABINET SECTION
CD cabinet section

not
supplied not
supplied
#1
1
6
#1
3
#1 #1
#1 #1
not supplied #7

#3
#1
#1

front panel section not

supplied

#1
#7 #1
#1 #1
not
supplied
#7

#6

5
#7
T902

not supplied #1 4

not 2
supplied

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 A-4748-828-A MAIN BOARD,COMPLETE 0 T902 1-439-782-11 TRANSFORMER, POWER
2 4-812-134-31 RIVET (DIA. 3.5), NYLON #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
3 4-245-014-81 CABINET REAR #3 7-685-647-11 SCREW +B3X10
04 1-769-744-52 CORD, POWER #6 7-685-650-79 SCREW +BVTP 3X16 TYPE2 N-S
5 1-860-065-11 POWER BOARD #7 7-685-246-14 SCREW +KTP 3X8 TYPE2 NON-SLIT

6 1-693-619-11 TUNER (FM/AM)

32
 CX-LEM400

7-2. FRONT PANEL SECTION

#1 not
61 supplied

57 #1

56 60
59
#1

64
58 #2 66

#1
not
supplied
#2

#1
55

63
not supplied

54
53 62
not
supplied

52
51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 A-4737-196-A DOOR CASSETTE ASSY 60 4-245-056-21 BUTTON (FUNCTION)
52 4-245-034-11 SPRING CASSETTE 61 A-4748-826-A CONTROL PC BOARD,COMPLETE
53 4-238-631-01 TAPE SPRING 62 1-796-352-41 DECK, MECHANICAL
54 4-245-018-11 HOLDER CASSETTE 63 4-224-104-41 DAMPER
55 4-245-059-01 KNOB VOLUME 64 A-4748-827-A SUB-CONTROL BOARD,COMPLETE

56 A-4741-194-A CABI-FRONT ASSY 66 3-701-748-00 CLAMP

57 4-245-057-21 BUTTON (POWER) #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
58 4-231-841-01 SPRING (HEART CAM-B) #2 7-685-661-14 SCREW +BVTP 4X12 TYPE2 IT-3
59 4-245-055-01 DECORATION,BUTTON

33
CX-LEM400

7-3. CD CABINET SECTION

101

111

112

113
not
114 supplied
S800

104

not
supplied

not supplied

107
115

107 107

115 115

107
BU-30DBD64S

115

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 4-246-195-11 LID, CD 113 4-249-238-01 MAGNET (18-30-5)
104 4-242-171-01 DAMPER 150 N 114 4-246-192-01 BASE, CHUCK N
107 4-231-451-01 INSULATOR (BU-30) 115 3-921-725-11 SCREW (2.6X10), +PWH
111 4-246-193-01 HOLDER, CHUCK A S800 1-692-960-11 SWITCH, PUSH (1 KEY)
112 4-246-191-01 PLATE, MAGNET

34
 CX-LEM400
Ver 1.1

7-4. BU-30DBD64S

601
602

not supplied

supplied with 603

604
not supplied

603

605

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
0 601 A-4461-740-A BU-30DBD64S//M 604 4-233-831-01 GEAR (LA)
602 1-782-817-11 WIRE (FLAT TYPE) (16 CORE) 605 A-4734-549-A BD BOARD (A),COMPLETE
603 4-233-832-01 GEAR (LB)

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.

35
CX-LEM400
SECTION 8
BD ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • CAPACITORS: • SEMICONDUCTORS
parts list may be different from the parts uF: µF In each case, u: µ, for example:
specified in the diagrams or the components • RESISTORS uA...: µA... , uPA... , µPA... ,
used on the set. All resistors are in ohms. uPB... , µPB... , uPC... , µPC... ,
• -XX, -X mean standardized parts, so they may METAL: metal-film resistor uPD..., µPD...
have some difference from the original one. METAL OXIDE: Metal Oxide-film resistor When indicating parts by reference number,
• Items marked “*” are not stocked since they F: nonflammable please include the board name.
are seldom required for routine service. Some • COILS
delay should be anticipated when ordering these uH: µH The components identified by mark 0 or
items. dotted line with mark 0 are critical for safety.
Replace only with part number specified.

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
A-4734-549-A BD BOARD, COMPLETE C230 1-164-360-11 CERAMIC CHIP 0.1uF 16V
******************* C231 1-100-588-21 ELECT CHIP 1000uF 20% 6.3V

< CAPACITOR > C249 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C250 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C101 1-164-315-11 CERAMIC CHIP 470PF 5% 50V C251 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C253 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C103 1-164-315-11 CERAMIC CHIP 470PF 5% 50V C254 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C104 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C107 1-162-921-11 CERAMIC CHIP 33PF 5% 50V C255 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C256 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C108 1-164-360-11 CERAMIC CHIP 0.1uF 16V C257 1-128-934-91 CERAMIC CHIP 0.33uF 20% 10V
C109 1-164-360-11 CERAMIC CHIP 0.1uF 16V C258 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C110 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C259 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C111 1-126-607-11 ELECT CHIP 47uF 20% 4V
C112 1-164-360-11 CERAMIC CHIP 0.1uF 16V C260 1-128-590-11 ELECT CHIP 100uF 20% 6.3V
C261 1-126-246-11 ELECT CHIP 220uF 20% 4V
C113 1-128-995-21 ELECT CHIP 100uF 20% 10V C263 1-126-607-11 ELECT CHIP 47uF 20% 4V
C114 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C264 1-126-607-11 ELECT CHIP 47uF 20% 4V
C115 1-128-995-21 ELECT CHIP 100uF 20% 10V C265 1-126-607-11 ELECT CHIP 47uF 20% 4V
C116 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C117 1-164-360-11 CERAMIC CHIP 0.1uF 16V C266 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C267 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C118 1-115-156-11 CERAMIC CHIP 1uF 10V C268 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C119 1-115-156-11 CERAMIC CHIP 1uF 10V C269 1-126-607-11 ELECT CHIP 47uF 20% 4V
C121 1-216-864-11 METAL CHIP 0 5% 1/16W C270 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C122 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C131 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V C271 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C272 1-216-864-11 METAL CHIP 0 5% 1/16W
C132 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C273 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C133 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V C274 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C150 1-128-394-11 ELECT CHIP 220uF 20% 10V C292 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C151 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C152 1-164-360-11 CERAMIC CHIP 0.1uF 16V C310 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C313 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C153 1-164-360-11 CERAMIC CHIP 0.1uF 16V C314 1-115-156-11 CERAMIC CHIP 1uF 10V
C156 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C316 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C169 1-128-394-11 ELECT CHIP 220uF 20% 10V
C202 1-164-360-11 CERAMIC CHIP 0.1uF 16V < CONNECTOR >
C203 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
CN101 1-794-424-11 CONNECTOR, FCC/FPC 16P
C205 1-164-360-11 CERAMIC CHIP 0.1uF 16V CN102 1-784-834-21 CONNECTOR, FFC (LIF (NON-ZIF)) 23P
C208 1-164-360-11 CERAMIC CHIP 0.1uF 16V CN104 1-784-863-21 CONNECTOR, FFC (LIF (NON-ZIF)) 11P
C209 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C211 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < FERRITE BEAD >
C212 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V
FB102 1-216-864-11 METAL CHIP 0 5% 1/16W
C213 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V FB103 1-216-864-11 METAL CHIP 0 5% 1/16W
C215 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V FB104 1-216-864-11 METAL CHIP 0 5% 1/16W
C216 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V ∗ FB161 1-469-670-21 FERRITE 0uH
C222 1-164-360-11 CERAMIC CHIP 0.1uF 16V FB201 1-216-295-91 SHORT CHIP 0
C224 1-115-156-11 CERAMIC CHIP 1uF 10V
FB203 1-216-864-11 METAL CHIP 0 5% 1/16W
C226 1-126-607-11 ELECT CHIP 47uF 20% 4V FB204 1-216-295-91 SHORT CHIP 0
C227 1-164-360-11 CERAMIC CHIP 0.1uF 16V FB291 1-216-864-11 METAL CHIP 0 5% 1/16W
C229 1-164-360-11 CERAMIC CHIP 0.1uF 16V FB351 1-216-864-11 METAL CHIP 0 5% 1/16W

36
 CX-LEM400
BD
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< IC > R220 1-216-821-11 METAL CHIP 1K 5% 1/16W
R221 1-216-809-11 METAL CHIP 100 5% 1/16W
IC101 8-752-408-73 IC CXD3068Q
IC102 8-759-713-70 IC AN41020A R222 1-216-809-11 METAL CHIP 100 5% 1/16W
IC103 8-752-106-21 IC CXA2647N-T4 R223 1-216-809-11 METAL CHIP 100 5% 1/16W
IC104 6-701-810-01 IC TC94A20F-CX4 R224 1-216-809-11 METAL CHIP 100 5% 1/16W
IC121 6-700-394-01 IC BA25BC0FP-E2 R225 1-216-809-11 METAL CHIP 100 5% 1/16W
R226 1-216-809-11 METAL CHIP 100 5% 1/16W
< JUMPER RESISTOR >
R227 1-216-809-11 METAL CHIP 100 5% 1/16W
JR5 1-216-864-11 METAL CHIP 0 5% 1/16W R230 1-216-811-11 METAL CHIP 150 5% 1/16W
R231 1-216-815-11 METAL CHIP 330 5% 1/16W
< COIL > R232 1-216-815-11 METAL CHIP 330 5% 1/16W
R233 1-216-815-11 METAL CHIP 330 5% 1/16W
L101 1-412-032-11 INDUCTOR CHIP 100uH
L163 1-216-864-11 METAL CHIP 0 5% 1/16W R249 1-216-818-11 METAL CHIP 560 5% 1/16W
R250 1-216-813-11 METAL CHIP 220 5% 1/16W
< TRANSISTOR > R251 1-216-813-11 METAL CHIP 220 5% 1/16W
R252 1-216-857-11 METAL CHIP 1M 5% 1/16W
Q101 8-729-046-90 TRANSISTOR 2SB970- (TX) .S0 R253 1-216-821-11 METAL CHIP 1K 5% 1/16W

< RESISTOR > R255 1-216-809-11 METAL CHIP 100 5% 1/16W

R257 1-216-809-11 METAL CHIP 100 5% 1/16W
R101 1-216-864-11 METAL CHIP 0 5% 1/16W R259 1-216-809-11 METAL CHIP 100 5% 1/16W
R102 1-216-835-11 METAL CHIP 15K 5% 1/16W R260 1-216-821-11 METAL CHIP 1K 5% 1/16W
R103 1-216-845-11 METAL CHIP 100K 5% 1/16W R261 1-164-360-11 CERAMIC CHIP 0.1uF 16V
R104 1-216-835-11 METAL CHIP 15K 5% 1/16W
R105 1-216-821-11 METAL CHIP 1K 5% 1/16W R265 1-216-813-11 METAL CHIP 220 5% 1/16W
R266 1-216-813-11 METAL CHIP 220 5% 1/16W
R111 1-216-847-11 METAL CHIP 150K 5% 1/16W R271 1-216-833-11 METAL CHIP 10K 5% 1/16W
R113 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R272 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R114 1-216-852-11 METAL CHIP 390K 5% 1/16W R275 1-216-833-11 METAL CHIP 10K 5% 1/16W
R115 1-216-839-11 METAL CHIP 33K 5% 1/16W
R116 1-216-839-11 METAL CHIP 33K 5% 1/16W R276 1-216-809-11 METAL CHIP 100 5% 1/16W
R279 1-216-809-11 METAL CHIP 100 5% 1/16W
R117 1-216-852-11 METAL CHIP 390K 5% 1/16W R284 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
R118 1-216-833-11 METAL CHIP 10K 5% 1/16W R291 1-216-864-11 METAL CHIP 0 5% 1/16W
R120 1-216-846-11 METAL CHIP 120K 5% 1/16W R303 1-216-864-11 METAL CHIP 0 5% 1/16W
R122 1-216-845-11 METAL CHIP 100K 5% 1/16W
R123 1-216-791-11 METAL CHIP 3.3 5% 1/16W R308 1-216-864-11 METAL CHIP 0 5% 1/16W
R309 1-216-864-11 METAL CHIP 0 5% 1/16W
R125 1-216-841-11 METAL CHIP 47K 5% 1/16W R310 1-216-864-11 METAL CHIP 0 5% 1/16W
R126 1-216-841-11 METAL CHIP 47K 5% 1/16W R311 1-216-864-11 METAL CHIP 0 5% 1/16W
R131 1-216-843-11 METAL CHIP 68K 5% 1/16W R313 1-216-864-11 METAL CHIP 0 5% 1/16W
R132 1-216-851-11 METAL CHIP 330K 5% 1/16W
R133 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R314 1-216-864-11 METAL CHIP 0 5% 1/16W
R316 1-216-864-11 METAL CHIP 0 5% 1/16W
R151 1-216-845-11 METAL CHIP 100K 5% 1/16W R318 1-216-864-11 METAL CHIP 0 5% 1/16W
R152 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R319 1-216-864-11 METAL CHIP 0 5% 1/16W
R155 1-216-864-11 METAL CHIP 0 5% 1/16W R321 1-216-864-11 METAL CHIP 0 5% 1/16W
R166 1-216-864-11 METAL CHIP 0 5% 1/16W
R167 1-216-864-11 METAL CHIP 0 5% 1/16W R351 1-216-864-11 METAL CHIP 0 5% 1/16W

R168 1-216-864-11 METAL CHIP 0 5% 1/16W < VARIABLE RESISTOR >

R169 1-216-864-11 METAL CHIP 0 5% 1/16W
R199 1-216-864-11 METAL CHIP 0 5% 1/16W RV101 1-223-997-21 RES, CARBON ADJ VAR 47K
R201 1-216-839-11 METAL CHIP 33K 5% 1/16W
R202 1-216-833-11 METAL CHIP 10K 5% 1/16W < VIBRATOR >

R203 1-216-845-11 METAL CHIP 100K 5% 1/16W X201 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
R204 1-216-827-11 METAL CHIP 3.3K 5% 1/16W ************************************************************
R205 1-216-821-11 METAL CHIP 1K 5% 1/16W
R206 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R207 1-216-857-11 METAL CHIP 1M 5% 1/16W

R216 1-216-857-11 METAL CHIP 1M 5% 1/16W

R218 1-216-821-11 METAL CHIP 1K 5% 1/16W
R219 1-216-821-11 METAL CHIP 1K 5% 1/16W

37
CX-LEM400
CONTROL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
A-4748-826-A CONTROL BOARD, COMPLETE < IC >
*************************
IC801 6-803-369-01 IC LC876780B-52C5-E
4-245-052-01 HOLDER FLT IC802 6-702-906-01 IC NJL64H380A
IC803 8-759-637-58 IC PST592C-T
< CAPACITOR >
< JUMPER RESISTOR >
C801 1-162-975-11 CERAMIC CHIP 24PF 5% 50V
C802 1-162-975-11 CERAMIC CHIP 24PF 5% 50V JW801 1-216-864-11 METAL CHIP 0 5% 1/16W
C803 1-162-974-11 CERAMIC CHIP 0.01uF 50V JW802 1-216-864-11 METAL CHIP 0 5% 1/16W
C804 1-126-382-11 ELECT 100uF 20% 6.3V JW803 1-216-864-11 METAL CHIP 0 5% 1/16W
C805 1-126-514-11 ELECT 22uF 20% 16V JW821 1-412-473-21 INDUCTOR 0uH
JW871 1-216-864-11 METAL CHIP 0 5% 1/16W
C806 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C807 1-162-974-11 CERAMIC CHIP 0.01uF 50V < TRANSISTOR >
C808 1-126-382-11 ELECT 100uF 20% 6.3V
C809 1-162-974-11 CERAMIC CHIP 0.01uF 50V Q815 8-729-034-51 TRANSISTOR KTC3875
C810 1-162-974-11 CERAMIC CHIP 0.01uF 50V
< RESISTOR >
C811 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C812 1-126-382-11 ELECT 100uF 20% 6.3V R701 1-216-821-11 METAL CHIP 1K 5% 1/16W
C813 1-162-974-11 CERAMIC CHIP 0.01uF 50V R702 1-216-821-11 METAL CHIP 1K 5% 1/16W
C814 1-126-382-11 ELECT 100uF 20% 6.3V R703 1-216-809-11 METAL CHIP 100 5% 1/16W
C815 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V R704 1-216-821-11 METAL CHIP 1K 5% 1/16W
R705 1-249-417-11 CARBON 1K 5% 1/4W F
C816 1-164-160-11 CERAMIC CHIP 20PF 5% 50V
C817 1-164-160-11 CERAMIC CHIP 20PF 5% 50V R706 1-216-809-11 METAL CHIP 100 5% 1/16W
C820 1-162-974-11 CERAMIC CHIP 0.01uF 50V R707 1-216-826-11 METAL CHIP 2.7K 5% 1/16W
C821 1-162-974-11 CERAMIC CHIP 0.01uF 50V R708 1-216-847-11 METAL CHIP 150K 5% 1/16W
C822 1-126-514-11 ELECT 22uF 20% 16V R709 1-216-843-11 METAL CHIP 68K 5% 1/16W
R713 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
C828 1-126-935-11 ELECT 470uF 20% 6.3V
C829 1-113-340-11 ELECT 47uF 20% 25V R714 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
C830 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R715 1-216-826-11 METAL CHIP 2.7K 5% 1/16W
C831 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R716 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
C834 1-126-794-11 ELECT 4.7uF 20% 50V R717 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R803 1-216-821-11 METAL CHIP 1K 5% 1/16W
C835 1-126-794-11 ELECT 4.7uF 20% 50V
C836 1-162-918-11 CERAMIC CHIP 18PF 5% 50V R804 1-216-821-11 METAL CHIP 1K 5% 1/16W
C837 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V R805 1-216-821-11 METAL CHIP 1K 5% 1/16W
C839 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R806 1-216-821-11 METAL CHIP 1K 5% 1/16W
C841 1-162-974-11 CERAMIC CHIP 0.01uF 50V R807 1-216-821-11 METAL CHIP 1K 5% 1/16W
R808 1-216-821-11 METAL CHIP 1K 5% 1/16W
C842 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C843 1-162-927-11 CERAMIC CHIP 100PF 5% 50V R809 1-216-841-11 METAL CHIP 47K 5% 1/16W
R810 1-219-570-11 METAL CHIP 10M 5% 1/10W
< CONNECTOR > R811 1-216-837-11 METAL CHIP 22K 5% 1/16W
R812 1-216-821-11 METAL CHIP 1K 5% 1/16W
CNP803 1-793-991-11 CONNECTOR, FFC/FPC 23P R813 1-216-821-11 METAL CHIP 1K 5% 1/16W
CNP806 1-778-691-11 CONNECTOR, FFC/FPC 19P
R814 1-216-852-11 METAL CHIP 390K 5% 1/16W
< DIODE > R815 1-216-849-11 METAL CHIP 220K 5% 1/16W
R816 1-216-821-11 METAL CHIP 1K 5% 1/16W
D803 8-719-991-33 DIODE 1SS133T-77 R818 1-249-438-11 CARBON 56K 5% 1/4W
D807 8-719-988-61 DIODE 1SS355TE-17 R819 1-216-821-11 METAL CHIP 1K 5% 1/16W
D808 8-719-988-61 DIODE 1SS355TE-17
D809 8-719-988-61 DIODE 1SS355TE-17 R820 1-216-845-11 METAL CHIP 100K 5% 1/16W
D810 8-719-991-33 DIODE 1SS133T-77 R821 1-216-833-11 METAL CHIP 10K 5% 1/16W
R822 1-216-821-11 METAL CHIP 1K 5% 1/16W
D811 8-719-060-44 DIODE SLR-342VRT32 R823 1-216-821-11 METAL CHIP 1K 5% 1/16W
D812 8-719-988-61 DIODE 1SS355TE-17 R824 1-216-821-11 METAL CHIP 1K 5% 1/16W
D813 8-719-988-61 DIODE 1SS355TE-17
R825 1-216-821-11 METAL CHIP 1K 5% 1/16W
< FILTER > R826 1-216-821-11 METAL CHIP 1K 5% 1/16W
R827 1-249-417-11 CARBON 1K 5% 1/4W F
FL801 1-518-900-11 INDICATOR TUBE, FLUORESCENT R828 1-216-821-11 METAL CHIP 1K 5% 1/16W
R829 1-216-821-11 METAL CHIP 1K 5% 1/16W

38
 CX-LEM400
CONTROL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R830 1-216-821-11 METAL CHIP 1K 5% 1/16W R893 1-216-845-11 METAL CHIP 100K 5% 1/16W
R831 1-216-821-11 METAL CHIP 1K 5% 1/16W
R832 1-216-821-11 METAL CHIP 1K 5% 1/16W R894 1-216-833-11 METAL CHIP 10K 5% 1/16W
R833 1-216-821-11 METAL CHIP 1K 5% 1/16W R895 1-216-821-11 METAL CHIP 1K 5% 1/16W
R834 1-216-821-11 METAL CHIP 1K 5% 1/16W R896 1-249-437-11 CARBON 47K 5% 1/4W
R897 1-216-821-11 METAL CHIP 1K 5% 1/16W
R835 1-216-821-11 METAL CHIP 1K 5% 1/16W R898 1-216-809-11 METAL CHIP 100 5% 1/16W
R836 1-216-821-11 METAL CHIP 1K 5% 1/16W
R839 1-216-833-11 METAL CHIP 10K 5% 1/16W R899 1-216-809-11 METAL CHIP 100 5% 1/16W
R840 1-216-825-11 METAL CHIP 2.2K 5% 1/16W RG01 1-216-845-11 METAL CHIP 100K 5% 1/16W
R841 1-216-825-11 METAL CHIP 2.2K 5% 1/16W RG02 1-216-845-11 METAL CHIP 100K 5% 1/16W
RG03 1-216-845-11 METAL CHIP 100K 5% 1/16W
R842 1-216-825-11 METAL CHIP 2.2K 5% 1/16W RG04 1-216-845-11 METAL CHIP 100K 5% 1/16W
R843 1-216-821-11 METAL CHIP 1K 5% 1/16W
R844 1-216-829-11 METAL CHIP 4.7K 5% 1/16W RG05 1-216-845-11 METAL CHIP 100K 5% 1/16W
R845 1-216-817-11 METAL CHIP 470 5% 1/16W RG06 1-216-845-11 METAL CHIP 100K 5% 1/16W
R846 1-216-833-11 METAL CHIP 10K 5% 1/16W RG07 1-216-845-11 METAL CHIP 100K 5% 1/16W
RG08 1-216-845-11 METAL CHIP 100K 5% 1/16W
R847 1-216-833-11 METAL CHIP 10K 5% 1/16W RP01 1-216-845-11 METAL CHIP 100K 5% 1/16W
R848 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R849 1-216-825-11 METAL CHIP 2.2K 5% 1/16W RP02 1-216-845-11 METAL CHIP 100K 5% 1/16W
R850 1-216-825-11 METAL CHIP 2.2K 5% 1/16W RP03 1-216-845-11 METAL CHIP 100K 5% 1/16W
R851 1-216-821-11 METAL CHIP 1K 5% 1/16W RP04 1-216-845-11 METAL CHIP 100K 5% 1/16W
RP05 1-216-845-11 METAL CHIP 100K 5% 1/16W
R852 1-216-829-11 METAL CHIP 4.7K 5% 1/16W RP06 1-216-845-11 METAL CHIP 100K 5% 1/16W
R853 1-216-817-11 METAL CHIP 470 5% 1/16W
R854 1-216-833-11 METAL CHIP 10K 5% 1/16W RP07 1-216-845-11 METAL CHIP 100K 5% 1/16W
R855 1-216-837-11 METAL CHIP 22K 5% 1/16W RP08 1-216-845-11 METAL CHIP 100K 5% 1/16W
R856 1-216-833-11 METAL CHIP 10K 5% 1/16W RP09 1-216-845-11 METAL CHIP 100K 5% 1/16W
RP10 1-216-845-11 METAL CHIP 100K 5% 1/16W
R857 1-216-821-11 METAL CHIP 1K 5% 1/16W RP11 1-216-845-11 METAL CHIP 100K 5% 1/16W
R858 1-216-821-11 METAL CHIP 1K 5% 1/16W
R859 1-216-809-11 METAL CHIP 100 5% 1/16W RP12 1-216-845-11 METAL CHIP 100K 5% 1/16W
R860 1-216-841-11 METAL CHIP 47K 5% 1/16W RP13 1-216-845-11 METAL CHIP 100K 5% 1/16W
R861 1-216-841-11 METAL CHIP 47K 5% 1/16W RP14 1-216-845-11 METAL CHIP 100K 5% 1/16W
RP15 1-216-845-11 METAL CHIP 100K 5% 1/16W
R863 1-216-833-11 METAL CHIP 10K 5% 1/16W RP16 1-216-845-11 METAL CHIP 100K 5% 1/16W
R864 1-216-833-11 METAL CHIP 10K 5% 1/16W
R865 1-216-833-11 METAL CHIP 10K 5% 1/16W RP17 1-216-845-11 METAL CHIP 100K 5% 1/16W
R866 1-216-833-11 METAL CHIP 10K 5% 1/16W RP18 1-216-845-11 METAL CHIP 100K 5% 1/16W
R867 1-216-841-11 METAL CHIP 47K 5% 1/16W RP19 1-216-845-11 METAL CHIP 100K 5% 1/16W
RP20 1-216-845-11 METAL CHIP 100K 5% 1/16W
R869 1-216-821-11 METAL CHIP 1K 5% 1/16W
R870 1-216-821-11 METAL CHIP 1K 5% 1/16W < VARIABLE RESISTOR >
R871 1-216-837-11 METAL CHIP 22K 5% 1/16W
R872 1-216-821-11 METAL CHIP 1K 5% 1/16W RV801 1-418-632-11 ENCODER, ROTARY (12 TYPE)
R873 1-216-821-11 METAL CHIP 1K 5% 1/16W
< SWITCH >
R874 1-216-821-11 METAL CHIP 1K 5% 1/16W
R875 1-216-821-11 METAL CHIP 1K 5% 1/16W S801 1-786-050-21 SWITCH, KEY BOARD
R876 1-216-821-11 METAL CHIP 1K 5% 1/16W (POWER u STANDBY/ON)
R877 1-216-841-11 METAL CHIP 47K 5% 1/16W S802 1-786-050-21 SWITCH, KEY BOARD (ECO)
R878 1-216-841-11 METAL CHIP 47K 5% 1/16W S803 1-786-050-21 SWITCH, KEY BOARD (CD)
S804 1-786-050-21 SWITCH, KEY BOARD (TUNER/BAND)
R879 1-216-837-11 METAL CHIP 22K 5% 1/16W S805 1-786-050-21 SWITCH, KEY BOARD (TAPE (REC MUTING))
R880 1-216-833-11 METAL CHIP 10K 5% 1/16W
R881 1-216-825-11 METAL CHIP 2.2K 5% 1/16W S806 1-786-050-21 SWITCH, KEY BOARD (AUX)
R882 1-216-833-11 METAL CHIP 10K 5% 1/16W S807 1-786-050-21 SWITCH, KEY BOARD (SYNCHRO REC)
R883 1-216-825-11 METAL CHIP 2.2K 5% 1/16W S808 1-786-050-21 SWITCH, KEY BOARD (REC START/PAUSE)
S809 1-786-050-21 SWITCH, KEY BOARD (RDS)
R884 1-216-821-11 METAL CHIP 1K 5% 1/16W S810 1-786-050-21 SWITCH, KEY BOARD (=)
R885 1-216-845-11 METAL CHIP 100K 5% 1/16W
R886 1-216-845-11 METAL CHIP 100K 5% 1/16W S811 1-786-050-21 SWITCH, KEY BOARD (+)
R887 1-216-845-11 METAL CHIP 100K 5% 1/16W S812 1-786-050-21 SWITCH, KEY BOARD (STOP)
R888 1-216-845-11 METAL CHIP 100K 5% 1/16W S813 1-786-050-21 SWITCH, KEY BOARD (TONE)

R889 1-216-845-11 METAL CHIP 100K 5% 1/16W < VIBRATOR >

R890 1-216-845-11 METAL CHIP 100K 5% 1/16W
R891 1-216-845-11 METAL CHIP 100K 5% 1/16W X801 1-567-098-41 VIBRATOR, CRYSTAL (32.768KHz)
R892 1-216-821-11 METAL CHIP 1K 5% 1/16W X802 1-795-880-11 VIBRATOR, CERAMIC (8.64MHz)
************************************************************

39
CX-LEM400
MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
A-4748-828-A MAIN BOARD, COMPLETE C226 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
********************* C227 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C228 1-126-965-91 ELECT 22uF 20% 50V
1-693-619-11 TUNER (FM/AM) C229 1-126-965-91 ELECT 22uF 20% 50V
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S C230 1-126-964-11 ELECT 10uF 20% 50V

< CAPACITOR > C232 1-126-963-11 ELECT 4.7uF 20% 50V

C233 1-130-492-11 MYLAR 0.056uF 5% 50V
C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C234 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C102 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C301 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C103 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C302 1-128-551-11 ELECT 22uF 20% 25V
C104 1-126-947-11 ELECT 47uF 20% 10V
C106 1-162-995-11 CERAMIC CHIP 0.022uF 50V C303 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C304 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C107 1-126-961-11 ELECT 2.2uF 20% 50V C305 1-126-934-11 ELECT 220uF 20% 10V
C108 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C309 1-126-767-11 ELECT 1000uF 20% 16V
C109 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C310 1-126-933-11 ELECT 100uF 20% 16V
C110 1-164-218-11 CERAMIC CHIP 180PF 0.25PF 50V
C111 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25V C312 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C313 1-126-933-11 ELECT 100uF 20% 16V
C112 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C314 1-136-967-11 MYLAR 0.012uF 5% 50V
C113 1-126-957-11 ELECT 0.22uF 20% 50V C315 1-126-947-11 ELECT 47uF 20% 25V
C114 1-126-959-11 ELECT 0.47uF 20% 50V C316 1-130-481-00 MYLAR 0.0068uF 5% 50V
C115 1-126-963-11 ELECT 4.7uF 20% 50V
C116 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C317 1-130-471-00 MYLAR 0.001uF 5% 50V
C318 1-130-483-00 MYLAR 0.01uF 5% 50V
C117 1-164-730-11 CERAMIC CHIP 0.0012uF 10% 50V C319 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C118 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V C320 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C119 1-126-961-11 ELECT 2.2uF 20% 50V C322 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C120 1-130-495-00 MYLAR 0.1uF 5% 50V
C121 1-130-495-00 MYLAR 0.1uF 5% 50V C323 1-128-548-11 ELECT 4700uF 20% 25V
C324 1-126-934-11 ELECT 220uF 20% 16V
C123 1-126-767-11 ELECT 1000uF 20% 16V C326 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C126 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C327 1-126-947-11 ELECT 47uF 20% 25V
C127 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C328 1-126-933-11 ELECT 100uF 20% 16V
C128 1-126-965-91 ELECT 22uF 20% 50V
C129 1-126-965-91 ELECT 22uF 20% 50V C329 1-126-933-11 ELECT 100uF 20% 16V
C330 1-126-934-11 ELECT 220uF 20% 10V
C130 1-126-964-11 ELECT 10uF 20% 50V C331 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C132 1-126-963-11 ELECT 4.7uF 20% 50V C332 1-126-933-11 ELECT 100uF 20% 16V
C133 1-130-492-11 MYLAR 0.056uF 5% 50V C333 1-126-935-11 ELECT 470uF 20% 16V
C134 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C335 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C336 1-126-965-91 ELECT 22uF 20% 50V
C202 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C337 1-126-965-91 ELECT 22uF 20% 50V
C203 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C338 1-104-665-11 ELECT 100uF 20% 10V
C204 1-126-947-11 ELECT 47uF 20% 10V C339 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C206 1-162-995-11 CERAMIC CHIP 0.022uF 50V
C207 1-126-961-11 ELECT 2.2uF 20% 50V C340 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C341 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C208 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C342 1-126-935-11 ELECT 470uF 20% 16V
C209 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C343 1-126-947-11 ELECT 47uF 20% 25V
C210 1-164-218-11 CERAMIC CHIP 180PF 0.25PF 50V C344 1-126-947-11 ELECT 47uF 20% 25V
C211 1-164-172-11 CERAMIC CHIP 0.0056uF 10% 25V
C212 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C345 1-126-934-11 ELECT 220uF 20% 10V
C346 1-126-768-11 ELECT 2200uF 20% 16V
C213 1-126-957-11 ELECT 0.22uF 20% 50V C347 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C214 1-126-959-11 ELECT 0.47uF 20% 50V C349 1-128-551-11 ELECT 22uF 20% 25V
C215 1-126-963-11 ELECT 4.7uF 20% 50V C350 1-127-884-21 CERAMIC 0.047uF 10% 50V
C216 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C217 1-164-730-11 CERAMIC CHIP 0.0012uF 10% 50V C351 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C352 1-126-959-11 ELECT 0.47uF 20% 50V
C218 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V C353 1-126-947-11 ELECT 47uF 20% 10V
C219 1-126-961-11 ELECT 2.2uF 20% 50V C355 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C220 1-130-495-00 MYLAR 0.1uF 5% 50V C356 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C221 1-130-495-00 MYLAR 0.1uF 5% 50V
C223 1-126-767-11 ELECT 1000uF 20% 16V

40
 CX-LEM400
MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< CONNECTOR > Q321 8-729-037-13 TRANSISTOR KTA1271Y-AT

∗ CN301 1-564-709-11 PIN, CONNECTOR (SMALL TYPE) 7P Q322 8-729-054-16 TRANSISTOR KRC402-RTK
CN302 1-784-776-11 CONNECTOR, FFC 15P Q323 8-729-037-13 TRANSISTOR KTA1271Y-AT
CN303 1-784-780-11 CONNECTOR, FFC 19P Q325 8-729-054-16 TRANSISTOR KRC402-RTK
CN304 1-784-776-11 CONNECTOR, FFC 15P Q326 8-729-034-50 TRANSISTOR KTA1504
CN306 1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P Q327 8-729-034-50 TRANSISTOR KTA1504

CN307 1-564-506-11 PLUG, CONNECTOR 3P Q328 8-729-045-62 TRANSISTOR 2SK2158-T2B

Q329 8-729-045-62 TRANSISTOR 2SK2158-T2B
< DIODE > Q330 8-729-045-62 TRANSISTOR 2SK2158-T2B
Q331 8-729-054-03 TRANSISTOR KRA303-RTK
D301 8-719-991-33 DIODE 1SS133T-77 Q332 8-729-054-03 TRANSISTOR KRA303-RTK
D302 8-719-991-33 DIODE 1SS133T-77
D303 8-719-109-72 DIODE MTZJ-T-77-3.9B Q333 8-729-054-16 TRANSISTOR KRC402-RTK
D304 8-719-109-89 DIODE MTZJ-T-77-5.6B Q334 8-729-037-03 TRANSISTOR KTA1266GR-AT
D305 8-719-921-42 DIODE MTZJ-T-77-5.1A Q335 8-729-037-03 TRANSISTOR KTA1266GR-AT
Q336 8-729-037-03 TRANSISTOR KTA1266GR-AT
D306 8-719-921-42 DIODE MTZJ-T-77-5.1A Q337 8-729-037-03 TRANSISTOR KTA1266GR-AT
D310 8-719-109-89 DIODE MTZJ-T-77-5.6B
D311 8-719-109-89 DIODE MTZJ-T-77-5.6B Q338 8-729-054-16 TRANSISTOR KRC402-RTK
D312 8-719-063-79 DIODE 1N4002B Q339 8-729-036-86 TRANSISTOR KTC3203Y-AT
D313 8-719-063-79 DIODE 1N4002B
< RESISTOR >
D317 8-719-991-33 DIODE 1SS133T-77
D318 8-719-982-15 DIODE MTZJ-T-77-27B R101 1-216-830-11 METAL CHIP 5.6K 5% 1/16W
D319 8-719-063-79 DIODE 1N4002B R102 1-216-840-11 METAL CHIP 39K 5% 1/16W
D320 8-719-063-79 DIODE 1N4002B R103 1-216-817-11 METAL CHIP 470 5% 1/16W
D321 8-719-063-79 DIODE 1N4002B R104 1-216-808-11 METAL CHIP 82 5% 1/16W
R105 1-216-852-11 METAL CHIP 390K 5% 1/16W
D322 8-719-063-79 DIODE 1N4002B
R106 1-216-830-11 METAL CHIP 5.6K 5% 1/16W
< IC > R107 1-216-847-11 METAL CHIP 150K 5% 1/16W
R108 1-216-832-11 METAL CHIP 8.2K 5% 1/16W
IC302 6-702-895-01 IC BD3881FV R109 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
IC303 6-704-881-01 IC LA4628 R111 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
IC305 8-759-231-57 IC TA7810S
R112 1-216-839-11 METAL CHIP 33K 5% 1/16W
< JACK > R113 1-216-821-11 METAL CHIP 1K 5% 1/16W
R114 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
J301 1-816-219-11 JACK, HEADPHONE R115 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
J302 1-536-708-81 TERMINAL BOARD, PUSH (4P) R116 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
J303 1-817-476-11 JACK, PIN 3P
R117 1-216-821-11 METAL CHIP 1K 5% 1/16W
< COIL > R118 1-216-832-11 METAL CHIP 8.2K 5% 1/16W
R119 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
L101 1-422-009-13 COIL, AIR-CORE R120 1-216-833-11 METAL CHIP 10K 5% 1/16W
L102 1-422-009-13 COIL, AIR-CORE R121 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
L201 1-422-009-13 COIL, AIR-CORE
L202 1-422-009-13 COIL, AIR-CORE R122 1-216-843-11 METAL CHIP 68K 5% 1/16W
R123 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
< TRANSISTOR > R124 1-216-835-11 METAL CHIP 15K 5% 1/16W
R125 1-216-837-11 METAL CHIP 22K 5% 1/16W
Q305 8-729-036-86 TRANSISTOR KTC3203Y-AT R126 1-216-837-11 METAL CHIP 22K 5% 1/16W
Q306 8-729-037-13 TRANSISTOR KTA1271Y-AT
Q307 8-729-028-54 TRANSISTOR KTC3205-Y-AT R128 1-216-820-11 METAL CHIP 820 5% 1/16W
Q308 8-729-037-13 TRANSISTOR KTA1271Y-AT R129 1-249-385-11 CARBON 2.2 5% 1/6W F
Q309 8-729-054-16 TRANSISTOR KRC402-RTK R130 1-249-385-11 CARBON 2.2 5% 1/6W F
R131 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
Q310 8-729-028-54 TRANSISTOR KTC3205-Y-AT R132 1-216-821-11 METAL CHIP 1K 5% 1/16W
Q311 8-729-037-13 TRANSISTOR KTA1271Y-AT
Q312 8-729-036-86 TRANSISTOR KTC3203Y-AT R136 1-216-833-11 METAL CHIP 10K 5% 1/16W
Q313 8-729-036-86 TRANSISTOR KTC3203Y-AT R137 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
Q314 8-729-037-13 TRANSISTOR KTA1271Y-AT R138 1-249-408-11 CARBON 180 5% 1/4W F
R139 1-249-408-11 CARBON 180 5% 1/4W F
Q315 8-729-054-16 TRANSISTOR KRC402-RTK R140 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
Q317 8-729-028-54 TRANSISTOR KTC3205-Y-AT
Q319 8-729-040-76 TRANSISTOR KTA1273-Y-AT R142 1-216-837-11 METAL CHIP 22K 5% 1/16W
Q320 8-729-054-16 TRANSISTOR KRC402-RTK R143 1-216-834-11 METAL CHIP 12K 5% 1/16W

41
CX-LEM400
MAIN POWER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R201 1-216-830-11 METAL CHIP 5.6K 5% 1/16W R325 1-216-845-11 METAL CHIP 100K 5% 1/16W
R202 1-216-840-11 METAL CHIP 39K 5% 1/16W R326 1-216-845-11 METAL CHIP 100K 5% 1/16W
R203 1-216-817-11 METAL CHIP 470 5% 1/16W R327 1-216-833-11 METAL CHIP 10K 5% 1/16W
R328 1-216-821-11 METAL CHIP 1K 5% 1/16W
R204 1-216-808-11 METAL CHIP 82 5% 1/16W R329 1-216-821-11 METAL CHIP 1K 5% 1/16W
R205 1-216-852-11 METAL CHIP 390K 5% 1/16W
R206 1-216-830-11 METAL CHIP 5.6K 5% 1/16W R330 1-216-841-11 METAL CHIP 47K 5% 1/16W
R207 1-216-847-11 METAL CHIP 150K 5% 1/16W R331 1-216-841-11 METAL CHIP 47K 5% 1/16W
R208 1-216-832-11 METAL CHIP 8.2K 5% 1/16W R332 1-216-821-11 METAL CHIP 1K 5% 1/16W
R336 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R209 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R337 1-216-845-11 METAL CHIP 100K 5% 1/16W
R211 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R212 1-216-839-11 METAL CHIP 33K 5% 1/16W R338 1-249-393-11 CARBON 10 5% 1/4W F
R213 1-216-821-11 METAL CHIP 1K 5% 1/16W R339 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R214 1-216-824-11 METAL CHIP 1.8K 5% 1/16W R340 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R341 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R215 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R342 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R216 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R217 1-216-821-11 METAL CHIP 1K 5% 1/16W R343 1-249-387-11 CARBON 3.3 5% 1/4W F
R218 1-216-832-11 METAL CHIP 8.2K 5% 1/16W R344 1-249-387-11 CARBON 3.3 5% 1/4W F
R219 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R345 1-249-387-11 CARBON 3.3 5% 1/4W F
R346 1-249-387-11 CARBON 3.3 5% 1/4W F
R220 1-216-833-11 METAL CHIP 10K 5% 1/16W R347 1-216-821-11 METAL CHIP 1K 5% 1/16W
R221 1-216-823-11 METAL CHIP 1.5K 5% 1/16W
R222 1-216-843-11 METAL CHIP 68K 5% 1/16W R348 1-216-821-11 METAL CHIP 1K 5% 1/16W
R223 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R349 1-216-864-11 METAL CHIP 0 5% 1/16W
R224 1-216-835-11 METAL CHIP 15K 5% 1/16W R350 1-216-833-11 METAL CHIP 10K 5% 1/16W
R351 1-216-833-11 METAL CHIP 10K 5% 1/16W
R225 1-216-837-11 METAL CHIP 22K 5% 1/16W R352 1-249-413-11 CARBON 470 5% 1/4W F
R226 1-216-837-11 METAL CHIP 22K 5% 1/16W
R228 1-216-820-11 METAL CHIP 820 5% 1/16W R353 1-249-389-11 CARBON 4.7 5% 1/4W F
R229 1-249-385-11 CARBON 2.2 5% 1/6W F R354 1-216-833-11 METAL CHIP 10K 5% 1/16W
R230 1-249-385-11 CARBON 2.2 5% 1/6W F R355 1-216-845-11 METAL CHIP 100K 5% 1/16W
R356 1-216-841-11 METAL CHIP 47K 5% 1/16W
R231 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R357 1-216-841-11 METAL CHIP 47K 5% 1/16W
R232 1-216-821-11 METAL CHIP 1K 5% 1/16W
R236 1-216-833-11 METAL CHIP 10K 5% 1/16W R358 1-216-821-11 METAL CHIP 1K 5% 1/16W
R237 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R359 1-216-864-11 METAL CHIP 0 5% 1/16W
R238 1-249-408-11 CARBON 180 5% 1/4W F
< TRANSFORMER >
R239 1-249-408-11 CARBON 180 5% 1/4W F
R240 1-216-825-11 METAL CHIP 2.2K 5% 1/16W 0 T301 1-433-372-31 TRANSFORMER, BIAS OSCILLATION
R242 1-216-837-11 METAL CHIP 22K 5% 1/16W ************************************************************
R243 1-216-834-11 METAL CHIP 12K 5% 1/16W
R301 1-216-833-11 METAL CHIP 10K 5% 1/16W 1-860-065-11 POWER BOARD
*************
R302 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R303 1-216-829-11 METAL CHIP 4.7K 5% 1/16W < CAPACITOR >
R304 1-216-817-11 METAL CHIP 470 5% 1/16W
R305 1-216-817-11 METAL CHIP 470 5% 1/16W C905 1-101-005-00 CERAMIC 22000PF 50V
R309 1-249-389-11 CARBON 4.7 5% 1/4W F C906 1-101-005-00 CERAMIC 22000PF 50V
C907 1-101-005-00 CERAMIC 22000PF 50V
R310 1-249-387-11 CARBON 3.3 5% 1/4W F C908 1-101-005-00 CERAMIC 22000PF 50V
R311 1-216-837-11 METAL CHIP 22K 5% 1/16W C909 1-101-005-00 CERAMIC 22000PF 50V
R312 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R313 1-216-841-11 METAL CHIP 47K 5% 1/16W C910 1-101-005-00 CERAMIC 22000PF 50V
R314 1-216-830-11 METAL CHIP 5.6K 5% 1/16W C911 1-101-005-00 CERAMIC 22000PF 50V
C912 1-101-005-00 CERAMIC 22000PF 50V
R315 1-216-825-11 METAL CHIP 2.2K 5% 1/16W C913 1-101-005-00 CERAMIC 22000PF 50V
R316 1-216-817-11 METAL CHIP 470 5% 1/16W C914 1-101-005-00 CERAMIC 22000PF 50V
R317 1-216-841-11 METAL CHIP 47K 5% 1/16W
R318 1-216-813-11 METAL CHIP 220 5% 1/16W C915 1-101-005-00 CERAMIC 22000PF 50V
R319 1-216-857-11 METAL CHIP 1M 5% 1/16W C916 1-101-005-00 CERAMIC 22000PF 50V

R320 1-216-829-11 METAL CHIP 4.7K 5% 1/16W < CONNECTOR >

R321 1-216-845-11 METAL CHIP 100K 5% 1/16W
R322 1-216-821-11 METAL CHIP 1K 5% 1/16W ∗ CN901 1-764-333-11 PLUG, CONNECTOR 10P
R323 1-216-821-11 METAL CHIP 1K 5% 1/16W ∗ CN902 1-793-660-11 PIN, CONNECTOR (PC BOARD) 3P
R324 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.

42
 CX-LEM400
POWER SUB-CONTROL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< DIODE > R711 1-216-821-11 METAL CHIP 1K 5% 1/16W
R712 1-216-821-11 METAL CHIP 1K 5% 1/16W
D906 8-719-991-33 DIODE 1SS133T-77 R718 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
D907 8-719-063-79 DIODE 1N4002B R719 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
D908 8-719-063-79 DIODE 1N4002B
D909 8-719-063-79 DIODE 1N4002B R720 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
D910 8-719-063-79 DIODE 1N4002B ************************************************************

D911 8-719-063-79 DIODE 1N4002B MISCELLANEOUS

D912 8-719-063-79 DIODE 1N4002B **************
D913 8-719-063-79 DIODE 1N4002B
D914 8-719-063-79 DIODE 1N4002B 04 1-769-744-52 CORD, POWER
D916 8-719-046-47 DIODE 1N5401M 6 1-693-619-11 TUNER (FM/AM)
602 1-782-817-11 WIRE (FLAT TYPE)(16 CORE)
D917 8-719-046-47 DIODE 1N5401M
D918 8-719-046-47 DIODE 1N5401M
D919 8-719-046-47 DIODE 1N5401M
D920 8-719-991-33 DIODE 1SS133T-77
D921 8-719-991-33 DIODE 1SS133T-77

D922 8-719-063-79 DIODE 1N4002B

D923 8-719-063-79 DIODE 1N4002B
D924 8-719-063-79 DIODE 1N4002B
D925 8-719-063-79 DIODE 1N4002B

< LINE FILTER >

0 LF901 1-402-663-11 TRANSFORMER, LINE FILTER (LFT)

< RESISTOR >

R901 1-249-437-11 CARBON 47K 5% 1/4W

R902 1-249-437-11 CARBON 47K 5% 1/4W
R907 1-212-881-11 FUSIBLE 100 5% 1/4W

< RELAY >

0 RY901 1-755-276-11 RELAY, POWER

< TRANSFORMER >

0 T901 1-439-779-11 TRANSFORMER, POWER

0 T902 1-439-782-11 TRANSFORMER, POWER
************************************************************

A-4748-827-A SUB-CONTROL BOARD, COMPLETE

*****************************

< CAPACITOR >

C832 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C840 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< CONNECTOR >

CNP807 1-779-287-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P

< IC >

IC804 8-759-233-75 IC TC74HCT245AF (EL)

IC805 6-701-985-01 IC BH2220FVM-TR

< RESISTOR >

R710 1-216-821-11 METAL CHIP 1K 5% 1/16W

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.

43