Full-service, independent repair center

- ~ ARTISAN®
~I TECHNOLOGY GROUP
with experienced engineers and technicians on staff.

We buy your excess, underutilized, and idle equipment

along with credit for buybacks and trade-ins.

Your definitive source Custom engineering

so your equipment works exactly as you specify.

for quality pre-owned

• Critical and expedited services • Leasing / Rentals/ Demos
equipment. • In stock/ Ready-to-ship • !TAR-certified secure asset solutions

Artisan Technology Group

Expert team I Trust guarantee I 100% satisfaction
(217) 352-9330 | [email protected] | artisantg.com A ll trade marks, brand names, and brands appearing he rein are the pro perty of their respective owne rs.

Visit our website - Click HERE

 HP Switch Software
Management and Configuration Guide
and Configuration Guide

YLR-Series User Guide

Part Number: P21-010106, YLR-Series SLED 3.0

Published: April 2015
Revision: B
DCO: 956
Disclaimer Notice US Export Control Compliance (for US products
only)
© IPG Photonics Corporation 2015. All rights reserved. You IPG is committed to complying with U.S. and foreign export,
may not copy, reproduce, transmit, store in a retrieval import and customs requirements. Export and re-export of
system or adapt this publication, in any form, in any media lasers and other products manufactured by IPG are subject
or by any means, without the prior written permission of IPG to U.S. and foreign laws and regulations, including the US
Photonics Corporation (IPG), except as allowed under Export Administration Regulations administered by the
applicable copyright laws. Permitted copies shall bear the Department of Commerce, Bureau of Industry and Security.
same copyright and proprietary notices which were The applicable restrictions vary depending on the specific
contained on the original version. product involved, intended application, the product
destination and the intended user. In some cases, an
This User Guide is provided “as is” and is subject to change individual validated export license is required from the US
and revision without notice. IPG believes that the Department of Commerce prior to resale or re-export of
information provided is accurate and reliable; however IPG certain products.
makes no warranty or representation, express or implied,
You are ultimately responsible for exporting any IPG product
regarding this document, including without limitation any
in accordance with the Export Administration Regulations
implied warranties of merchantability or fitness for a
and the U.S. Customs and Border Protection Regulations.
particular use, purpose or application, either alone or in
IPG recommends that you obtain your own legal advice
combination with any other device, equipment, apparatus,
when attempting to export. All export and custom
materials or process. Users must take full responsibility for
classifications and information provided by IPG is subject to
their application of any products.
change without notice. IPG makes no representation as to
the accuracy or reliability of the classification information
Further, IPG does not assume responsibility for use of the
provided. The stated classification only applies to
information contained in this document or for any
equipment as it left the IPG factory. Any modifications or
infringement of patents or other rights of third parties that
changes after leaving the IPG facility will be your
may result from its use. IPG shall not be liable for errors in
responsibility to obtain further classifications. IPG is in no
or omissions from this document or for any incidental,
way responsible for any damages whether direct,
consequential, indirect or special damages, including
consequential, incidental, or otherwise, suffered by you as
without limitation, lost profits, lost production costs or similar
a result of using or relying upon such classifications, groups,
damages, in connection with the furnishing, performance or
or symbols for any purpose whatsoever.
use of this material.
Information relating to U.S. export rules and regulations can
IPG grants no license, directly or indirectly, under any patent be found at the U.S. Bureau of Industry and Security
or other intellectual property rights from use of the Website. Information related to U.S. Customs and Border
information provided herein. Protection can be found at the U.S. Customs Website.

IPG, IPG Photonics and the IPG Logo are registered

trademarks of IPG Photonics Corporation. IPG has
identified words that are considered trademarks. Neither
the presence nor absence of trademark identifications
affects the legal status of any trademarks.

Patent Rights
This product is patented. See the product for more
information.
Preface

Ensure you read and understand this guide in its entirety and familiarize yourself with
the operating and maintenance instructions before you use the product. IPG strongly
recommends that all operators of the product read and pay particular attention to all
safety information contained herein prior to operating the product.
This guide should stay with the product to provide you and all future operators, users,
and owners of the product with important operating, safety, and other information.
For technical assistance concerning the product, contact IPG Customer Service.

Audience
The audience for this guide are system integrators and technicians responsible for
installing and operating the YLR-Series laser in industrial and non-industrial
installations.

i
Preface
Audience

ii
 Contents

Preface
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-i

1 Overview of the YLR-Series Fiber Lasers

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Safety Information and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Safety Features and Compliance to Government Requirements . . 1-3
Compliance to Regulatory Standards (on applicable units) . . . . . . 1-3
Class A Digital Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Electromagnetic Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Laser Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Emission-On Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Specular Reflections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Equipment and Solvents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Safety Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14
Optical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Environmental Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Additional Safety Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19

2 Using Your Device

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Model Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Laser Model Designation Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

iii
 Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
YLR Series — Front Panel View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
YLR Series — Rear Panel View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Optical Output Fiber Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Products with a Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Products with a Collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Model Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Unpacking a Unit from a Cardboard Box . . . . . . . . . . . . . . . . . . . 2-11
Unpacking a Unit from a Wooden Crates . . . . . . . . . . . . . . . . . . . 2-14
Using the YLR-Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Connecting Electrical Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Interface Wire Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Connections to External Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Interlock Safety Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Interface Connector Pin Assignments . . . . . . . . . . . . . . . . . . 2-19
Initial Power-Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Key Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
YLR-Series System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
Rear Panel: 7-pin and 24-pin Connectors . . . . . . . . . . . . . . . . . . . 2-26
Operation Control Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Turning on the Device in Local Control Mode . . . . . . . . . . . . . . . . 2-30
Turning on the Device in Remote Control Mode . . . . . . . . . . . . . . 2-30
Selecting Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Pulse Mode (QCW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Operational Sub-Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Standalone Mode (Modulation and Gate control disabled) . . 2-32
Modulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Gate Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
External (Analog) Power Control . . . . . . . . . . . . . . . . . . . . . . 2-32
Pulse Shaper Program (Optional Feature) . . . . . . . . . . . . . . . 2-33
Using the Touch-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

iv
3 Computer Interface/Commands
RS-232 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Ethernet TCP/IP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

4 Pulse Shaping
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Ethernet TCP/IP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
RS-232 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Key Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Installing the Pulse Shaper Software . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Configuring a Local Area Connection for Ethernet . . . . . . . . . . . . . 4-9
Pulse Shaper Configuration Procedures . . . . . . . . . . . . . . . . . . . . 4-12
Connecting using Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Connecting Using RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Using the Offline Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Exporting a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Importing a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Using the Pulse Shaper Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Laser Control Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20
Shape Editor Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
Creating a New Pulse Shape Profile . . . . . . . . . . . . . . . . . . . . . . . 4-27
Creating a Single Pulse Shape . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
Shifting a Pulse Shape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29
Pulse Shape Storage and Recall . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
On a Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30
On a Host PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
Deleting a Pulse Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31
Single Pulse Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33
Single Pulse Activation using the Touch-Display Screen . . . . . . . 4-34
Scaling Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
Creating a New Pulse Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36
Sequence Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37

v
 Creating a New Pulse Sequence . . . . . . . . . . . . . . . . . . . . . . . . . 4-38
Building a Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
Modifying a Pulse Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
Pulse Sequence Storage and Recall . . . . . . . . . . . . . . . . . . . . . . 4-42
On a Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
On a Host PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43
Deleting a Pulse Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43
Pulse Sequence Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45
Pulse Sequence Activation using the Touch-Screen Display . . . . 4-46
Remote Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47

5 Troubleshooting
Error Messages on the Display and Status Bits . . . . . . . . . . . . . . . . 5-1

A Web User Utility

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Configuration Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Configuring an Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . A-1
Configuring an RS-232 Serial Connection . . . . . . . . . . . . . . . . . . . A-1
Configuring a LAN Connection for Ethernet . . . . . . . . . . . . . . . . . . . A-2
Website Data Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
Accessing the Web User Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-7

B Service
Service and Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Serviceable Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Replacing Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Replacing the Filter Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2

C Optical Fiber Connector Inspection and Cleaning

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

vi
D Warranty
Limited Express Product Warranties . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Warranty Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Limitation of Remedies and Liabilities . . . . . . . . . . . . . . . . . . . . . . . D-2
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
Firmware License Agreement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
Software License Agreement for LaserNet™ . . . . . . . . . . . . . . . . . . D-6
IPG Laser GmbH® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
Single Use License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
MICROSOFT CORPORATION EMBEDDED SOFTWARE
END USER LICENSE AGREEMENT . . . . . . . . . . . . . . . . . . . . . . . . . D-10

E Product Returns
Returns to the United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
Shipping Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2
Warranty Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2
Non-Warranty Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2
Returns to Germany . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3

F Glossary
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-1

vii
viii
 1

Overview of the YLR-Series Fiber Lasers

Introduction
The IPG Photonics YLR-Series fiber lasers are developed to meet industrial market
demands of efficient reliable maintenance-free high power lasers. These lasers are a
diode-pumped Ytterbium fiber laser with output powers ranging from 1W up to 1.5
kW operating at the wavelength region of 1060 - 1100 nm.
The YLR-Series fiber lasers can be air or water-cooled. The wall plug efficiency for
a fiber laser is typically exceeds 30 percent. All YLR-Series fiber lasers are Class 4
laser products and are designed and tested with important safety features. Follow this
guide and apply laser safety practices for a safe and reliable device.
Laser light exhibits unique characteristics that pose safety hazards that are not
normally associated with other light sources. Therefore, all operators and other
people near the laser must be aware of these special hazards.

Audience
The audience for this guide are system integrators and technicians responsible for
installing and operating the IPG YLR-Series fiber lasers in industrial and non-
industrial installations.

1-1
Overview of the YLR-Series Fiber Lasers
Safety Information and Conventions

Safety Information and Conventions

To ensure the safe operation and optimal performance of the product, follow all
warnings in this guide. Safety precautions must be observed during all phases of
operation, maintenance, and service.
Operators must adhere to these recommendations and to apply sound laser safety
practices at all times. Never open the chassis. There are no user serviceable parts,
equipment or assemblies associated with this product. All internal service and
maintenance should only be performed by qualified IPG personnel.
Table 1-1 lists safety conventions and their meanings. These conventions are used
throughout this guide.

Table 1-1. Safety Symbols

Symbol Description
Text marked with an Electrical Warning symbol or Laser Warning
symbol refers to a potential personal hazard. It requires a procedure that, if
not correctly followed, can result in bodily harm to you or others.

Do not proceed beyond the Electrical Warning or Laser Warning symbols

until you completely understand and meet the required conditions.

Text marked with a Caution symbol refers to a potential product hazard. It

requires a procedure that, if not correctly followed, can result in damage or
destruction to the product or components.

Do not proceed beyond the Caution symbol until you completely understand
and meet the required conditions.

Text marked with Important refers to pertinent information regarding the

No symbol operation of the product. Ensure you do not overlook this information.

1-2
 Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

Safety Features and Compliance to

Government Requirements
Compliance to Regulatory Standards (on applicable
units)
EMC Emissions:
EN 55011:2009 + A1:2010
CISPR 11:2009 + A1:2010
FCC Class A
EMC Immunity:
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 61326-1:2006
EN 61000-4-2:2009
EN 61000-4-3:2006 + A1:2007 + A2:2010
EN 61000-4-4:2004+A1:2010
EN 61000-4-5:2006
EN 61000-4-6:2009
EN 61000-4-8:2010
EN 61000-4-11:2004
EMC Other:
This Class A digital apparatus complies with Canadian ICES-003.
Electrical Safety:
61010-1:2010
Laser Safety:
EN 60825-1:2007
CDRH 21 CFR 1040.10

1-3
Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

Functional Safety:
The following safety functions are implemented to fulfill the requirements of
EN ISO 13849-1:2008 + A1:2009 Cat.3 / PL d and Category 3 (Cat. 3). The
safety functions are implemented exclusively in hardware:
• Stop initiated by a safeguard: The safety electronics of the laser
monitors the feed fiber cable (optical fiber interlock). If the laser is
emitting and the feed fiber is disconnected from a mating device or
broken, the safety-related outputs become de-energized.
• Stop initiated by a safeguard: The safety electronics of the laser
monitors E-Stop input. If the laser is emitting and the E-Stop is
activated, the safety-related outputs become de-energized.
• Safe start/restart button: The safety electronics of the laser monitors
safety-related outputs. A fault in the safety-related outputs is detected
before the next demand upon the safety-related output.
• Discharge of stored energy: The safety electronics of the laser monitors
safety-related inputs. If the laser is emitting and a stop is initiated by a
safeguard, the stored energy for the laser is discharged.
• Prevention of unexpected startup: The safety electronics of the laser
monitors safety-related inputs. Start of restart cannot occur after
activation of a safeguard until safeguard is re-established and separate
deliberate action occurs.

Class A Digital Device

This equipment is tested and complies with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with this guide, can cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the users are required to correct the
interference at their own expense.

Electromagnetic Compatibility
Compliance of the YLR-Series lasers with the EMC requirements is certified by the
CE mark if identified by the CE label (Figure 1-1 on page 1-7).

1-4
 Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

The European requirements for Electromagnetic Compliance are specified in the

“EMC Directive.” Conformance to the “EMC Directive” is achieved through
compliance with the harmonized standards EN55011 for emission and EN 61326-
1:2006 for immunity. The laser meets the emission requirements for Class A, group
1 as specified in EN55011.

Laser Classification
The governmental standards and requirements specify that lasers must be classified
according to their output power or energy and the laser wavelength. All YLR-Series
lasers are classified as Class 4 laser products under 21 CFR, subchapter J, part II,
1040.10(d).
According to the European Community standards, this device is classified as Class
4 based on EN 60825-1, clause 9 This product emits invisible laser radiation at or
around a wavelength of 1070 nm, and the total light power radiated from the optical
output is greater than 20 to 1500 W (depending on model) per optical output port.
Direct or indirect exposure of this level of light intensity can cause damage to the
eye or skin. Despite the radiation being invisible, the beam can cause irreversible
damage to the retina and cornea. Appropriate and approved laser safety eyewear must
be worn at all times while the laser is operational.

WARNING: You must use appropriate laser safety eyewear when operating the
device. The selection of appropriate laser safety eyewear requires that the end
user accurately identify the range of wavelengths emitted from this product. If
the device is a tunable laser or Raman product, it emits light over a range of
wavelengths.

You must ensure that the laser safety eyewear used protects against light emitted
by the device over its entire range of wavelengths. Review the safety labeling on
the product (see Figure 1-1 on page 1-7) and verify that the personal protective
equipment (for example, enclosures, viewing windows or viewports, garments,
and eyewear) being used is adequate for the output power and wavelength
ranges listed on the product.

Suppliers include LaserVision USA, Kentek Corporation and Rockwell Laser

Industries offer this laser safety material and equipment. There are other laser
personal protective equipment providers. IPG provides the names of these
providers solely as a convenience and does not endorse or recommend any of
them, or their products or services. Furthermore, IPG assumes no liability for
any of their recommendations, products, or services.

1-5
Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

Whether the laser is used in a new installation or to retrofit an existing device,

the end user is solely responsible for determining the suitability of all personal
protective equipment.

CAUTION: Do not install or terminate fibers or collimators when laser is active.

WARNING: Use of controls or adjustments, or performance of procedures

other than those specified herein, can result in hazardous radiation exposure.

CAUTION: Use of the device in a manner other than that described herein can
impair the protection provided by the device.

Safety Label Locations

The YLR Series Laser has the required laser safety labels located on the outside of
the chassis in various locations. These include warning labels indicating removable
or displaceable of the protective housings, apertures through which laser radiation is
emitted and labels of certification and identification.
Figure 1-1 shows the required laser safety labels and the locations for the Water-
Cooled YLR-Series laser. Figure 1-2 on page 1-7 shows the required laser safety
labels and the locations for the Air-Cooled YLR-Series laser.
These include warning labels indicating removable or displaceable protective
housings, apertures through which laser radiation is emitted and labels of certification
and identification.

1-6
 Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

Figure 1-1. Safety Label Locations - WC YLR-Series Laser

Figure 1-2. Safety Label Locations - AC YLR-Series Laser

1-7
Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

Table 1-2. Safety Label Descriptions

Item Label Name Description

1 Aperture Label

2 FDA Compliance (for US Products)

3 Class 2M Laser Product Label for

Guide Laser

1-8
 Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

4 Class 4 Laser Product

(Models: YLR-10, YLR-15, YLR-20,
YLR-25, YLR-30)

4 Class 4 Laser Product

(Models: YLR-40, YLR-50, YLR-60
to YLR-70)

4 Class 4 Laser Product

(Models: YLR-75, YLR-100, YLR-
150)

1-9
Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

4 Class 4 Laser Product

(Models: YLR-200, YLR-250, YLR-
300, YLR-350)

4 Class 4 Laser Product

(Models: YLR-400, YLR-500, YLR-
600, YLR-700)

4 4. Class 4 Laser Product

(Models: YLR-750, YLR-800, YLR-
900, YLR-1000)

1-10
 Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

4 Class 4 Laser Product )

(Models: QCW YLR-150/1500)

4 4. Class 4 Laser Product

(Models: QCW YLR-300/3000)

5 Identification Plate (Products Made

in the United States)a

1-11
Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

5 Identification Plate (Products Made

in Germany)b

6 Laser Radiation Hazard Label

7 Protective Conductor Terminalc

8 Electrical Hazard Label

9 CE Complianced

1-12
 Overview of the YLR-Series Fiber Lasers
Safety Features and Compliance to Government Requirements

10 Fusee

a. Refer to Table 2-1 on page 2-2 for Model Designation Codes.

b. Refer to Table 2-1 on page 2-2 for Model Designation Codes.
c. This symbol is specifically reserved for the PROTECTIVE CONDUCTOR TERMINAL and no
other. It is placed at the equipment earthing point and is mandatory for all grounded equipment.
d. This label indicates compliance with CE marking requirements.
e. This symbol is accompanied with type and rating (for example, T15A, 250VAC, ¼ x 1-1/4).

Emission-On Indicator
The laser is equipped with a an Emission-On Indicator light located on the front panel
(see Figure 2-1 on page 2-3). The Emission-On Indicator is turned on when laser
emission is ready to emit.
If the laser aperture or a remote laser control is located more than two meters from
the indicator on the front panel, then an additional indicator must be located at the
aperture or remote control.
Emission ON, Pin 24 on the remote connector is active high when the laser is ready
to emit. It can used to provide a laser-ready warning at the aperture or remote control
when these are located two or more meters from the front panel.

1-13
Overview of the YLR-Series Fiber Lasers
General Safety Instructions

General Safety Instructions

WARNING: You must exercise caution to avoid and minimize specular

reflections as these reflections occur at the laser's wavelength and are invisible.

Specular Reflections
Often there can be numerous secondary laser beams produced at various angles near
the laser aperture. These beams are called “Specular Reflections” and are produced
when the laser light reflects off a surface where the primary beam is incident.
Although these secondary beams might be less powerful than the total power emitted
from the laser, the intensity might be great enough to cause damage to the eyes and
skin as well as materials surrounding the laser.

Equipment and Solvents

Light-sensitive elements in equipment, such as video cameras, photomultipliers and
photodiodes can also be damaged from exposure to the laser light.

WARNING: The laser light is strong enough to cut or weld metal, burn skin,
clothing, and paint. In addition, this light can ignite volatile substances such as
alcohol, gasoline, ether, and other solvents. Exposure to solvents or other
flammable materials and gases must be avoided and must be relocated away
from this device.

Safety Recommendations
IPG recommends that you follow these procedures to operate the IPG laser safely:
• Never look directly into the laser output port when power is supplied to the laser.
• Avoid positioning the laser and all optical components at eye level.
• Provide enclosures for laser beam.
• Ensure that all personal protective equipment (PPE) is suitable for the output power
and wavelength range listed on the laser safety labels that are affixed to the product.

1-14
 Overview of the YLR-Series Fiber Lasers
General Safety Instructions

• Use the laser in a room with access controlled by door interlocks. Post warning signs.
Limit access to the area to individuals who are trained in laser safety while operating
the laser.
• Avoid using the laser in a darkened environment.
• Do not enable the laser without a coupling fiber or equivalent attached to the optical
output connector.
• Always switch the laser off when working with the output such as mounting the fiber
or collimator into a fixture. If necessary, align the output at low output power and then
increase the output power gradually.
• Do not install or terminate fibers or collimators when laser is active.
• If this instrument is used in a manner not specified in this document, the protection
provided by the instrument may be impaired and the warranty will be voided.

Optical Safety

CAUTION: If the output of the device is delivered through a lens with an anti-
reflection coating, ensure that the lens is of good quality and clean. For cleaning
instructions, refer to “Optical Fiber Connector Inspection and Cleaning” on
page C-1.

Any dust on the end of the collimator assembly can burn the lens and damage
the laser.

Hot or molten pieces of metal can be present when using this laser. Exercise
caution if debris is being generated in your application.

Electrical Safety

WARNING: The input voltage to the laser is potentially lethal. All electrical
cables and connections should be treated as if it were a harmful level. All parts
of the electrical cable, connector, or device housing should be considered
dangerous.

To ensure electrical safety:

1. Make sure the device is properly grounded through the protective conductor of
the AC power cable. Any interruption of the protective grounding conductor
from the protective earth terminal can result in personal injury.
2. Always use your device in conjunction with properly grounded power source.

1-15
Overview of the YLR-Series Fiber Lasers
General Safety Instructions

3. For continued protection against fire hazard, replace the line fuses (if
applicable) with only the same types and ratings. The use of other fuses or
material is prohibited.
4. Before supplying the power to the instrument, ensure that the correct voltage
of the AC power source is used. Failure to use the correct voltage can cause
damage to the instrument.
5. Before switching the power on, ensure that line voltage corresponds to the
specified level.
6. There are no operator serviceable parts inside. Refer all servicing to qualified
IPG personnel. To prevent electrical shock, do not remove covers. Any
tampering with the product voids the warranty.

Environmental Safety

WARNING: Never look directly into a laser aperture (such as fiber, collimator,
or scanning head) when the Start button or remote Start circuit is activated.
Ensure that you wear appropriate laser safety eyewear at all times while
operating the product.

Proper enclosures must be used to secure a laser safe work area. This includes but is
not limited to laser safety signs, interlocks, appropriate warning devices and training/
safety procedures. In addition, it is important to install the output assembly away
from eye level.

WARNING: Ensure that all personal protective equipment (PPE) is suitable for
the output power and wavelength range listed on the laser safety labels that are
affixed to the product.

The interaction between the laser and the material being processed can also generate
high intensity UV and visible radiation. Ensure that all laser enclosures are in place
to prevent to prevent eye and skin exposure to visible and invisible collateral
radiation.

1-16
 Overview of the YLR-Series Fiber Lasers
General Safety Instructions

CAUTION: Damage to the laser is possible, unless caution is employed in

operating the device.

IPG provides the following recommendations to promote the long life of the IPG
laser:
• Do not expose the device to a high moisture environment (>95% humidity).

CAUTION: Water-cooled lasers must not operate at temperatures below the

respective ambient dewpoint (see Table 1-3 on page 1-17).

• The device might have fans for active cooling. Ensure there is sufficient airflow to
cool the device. Any objects or debris that cover the ventilation holes must be
inspected. Filter media should be inspected at regular intervals to maintain sufficient
airflow into the device.
• Operation at higher temperatures accelerate aging, increase threshold current, and
lower slope efficiency. If the device is overheated, do not use it and call IPG for
assistance.
• Ensure that the work area is properly vented. gases, sparks and debris that can be
generated from interaction between the laser and the work surface can pose additional
safety hazards.
• Inspect the filter media weekly and clean or replace as needed. See “Replacing the
Filter Media” on page B-2 for details.

Table 1-3. Dewpoint Table

1-17
Overview of the YLR-Series Fiber Lasers
General Safety Instructions

1 These values are calculated using the August-Roche-Magnus approximation.

1-18
 Overview of the YLR-Series Fiber Lasers
Additional Safety Resources

Additional Safety Resources

For additional information regarding Laser Safety, refer to the following list:
Laser Institute of America (LIA)
13501 Ingenuity Drive, Suite 128
Orlando, Florida 32826
Phone: 407.380.1553, Fax: 407.380.5588
Toll Free: 1.800.34.LASER
American National Standards Institute
ANSI Z136.1, American National Standard for the Safe Use of Lasers
(Available through LIA)
International Electro-technical Commission
IEC 60825-1, Edition 2
Safety of laser products -
Part 1: Equipment classification, requirements and user's guide.
(Available through LIA)
Center for Devices and Radiological Health
21 CFR 1040.10 - Performance Standards for Light-Emitting Products
US Department of Labor - OSHA
Publication 8-1.7 - Guidelines for Laser Safety and Hazard Assessment
US Department of Labor - OSHA
Publication 8-1.7 - Guidelines for Laser Safety and Hazard Assessment
Laser Safety Equipment
Laurin Publishing
Laser safety equipment and Buyer's Guides

Note IPG Photonics recommends that the user of this product investigate any local, state
or country requirements as well as facility or building requirements that might apply
to installing or using a laser or laser device.
Ensure that the standard you are using such as ANSI, IEC, and OSHA are current.

1-19
Overview of the YLR-Series Fiber Lasers
Additional Safety Resources

1-20
 2

Using Your Device

Overview
The IPG Photonics YLR-Series fiber lasers are developed for use in industrial
applications. The lasers are compact and efficient letting you replace bulky and less
efficient lasers. Main application are welding, cutting, and brazing.

Main Features
• High quality fiber output
• High power
• Reliable, long lifetime
• Compact, rugged package
• Efficient
• External computer interface

Applications
• Industrial applications
• Scientific research

Model Configurations
IPG offers many YLR-Series configuration models. This guide is designed to provide
complete instructions for all models. Therefore, specific difference in models is noted
where applicable.

Laser Model Designation Codes

Figure 2-1 on page 2-2 shows the model designation methodology for all YLR-Series
lasers. In addition, models are also categorized according to chassis type with their
respective "U" or Rack Unit code.
The subsequent AC or WC code designates whether the model is air cooled or water
cooled.
The U categories offered are 3U-AC, 3U-WC, 4U-AC, 4U-WC, and 6U-AC.

2-1
Using Your Device
Model Configurations

Figure 2-1. YLR-Series Laser Models

Table 2-1. Laser Model Designation Codes

Number Item Code

1 YLR Ytterbium
Laser
19-inch Rack Mount

2 Power in W Range of 20 to 1500 Watts

3 Wavelength in nm Item is listed if wavelength is not standard. 1070 nm (standard)

4 Polarization/Output Beam MM — for Multi-Mode

Characteristic LP — for Linearly Polarized

If an item is not listed, then the beam is single-mode and randomly

polarized.

5 Additional Information WC — Water Cooled device

AC — Air Cooled device

6 Additional Information The last two digits of the model year,

Table 2-2. Available YLR Series Models

Category Model

3U-AC YLR-20, YLR-30, YLR-50, and YLR-100-AC

3U-WC YLR-100-WC, YLR-200-WC, YLR-300-WC, YLR-400-WC, YLR-500-WC, YLR-600-WC,

and YLR-700-WC

4U-AC YLR-200-AC, YLR-300-AC, YLR-400-AC, and YLR-150/1500-QCW-AC

4U-WC YLR-1000-WC

6U-AC YLR-500-AC and YLR-600-AC

2-2
 Using Your Device
Certification

Certification
IPG Photonics certifies that your system is thoroughly tested and inspected and meets
published specifications prior to shipping. Upon receiving your device, check the
packaging and parts for any possible damage that might have occurred in transit. If
there is damage, contact IPG Photonics immediately. It is the responsibility of the
purchaser/end-user to bring the end system into compliance with all applicable
regulations.

YLR Series — Front Panel View

The YRL Series front panel includes two options: panel with a display and panel
without a display.
Figure 2-2 shows the front panel of the YLR-Series, which includes an option with
a display. Table 2-3 lists details for each component.
Figure 2-2. Front Panel View with Display

2-3
Using Your Device
YLR Series — Front Panel View

Table 2-3. Front Panel Descriptions

Item Feature Description

1 Keyswitch The 3-position key switch controls the laser operation mode:

(Local Interface option only) Left position — Chassis Powered On, Remote Control Mode
Central position — Chassis powered Off
Right position — Chassis Powered On, Local Control Mode

Note: The key cannot be removed in the Remote Control Mode or

Local Control Mode positions.

2 Emergency Stop Button Temporarily suspends power to the laser module. When active, the
(E-Stop) main DC power supply is disabled. You can reset it by turning
clockwise.
(Local Interface option only)

3 Start Button with Indicator When pressed, turns On the internal main power supply of the laser
assuming that the Power key is in the Local Mode position.
(Local interface option only)
When the indicator is On, the internal power supply is active and the
laser is capable of producing laser radiation.

4 Touch-Screen Display Use to set device settings and to display measured parameters and
alarm messages.
(Local interface option only)

5 Emission On Indicator Local Control Mode:

The indicator blinks for a short period after emission is enabled and
before laser radiation is emitted. once laser emission is ON, the
indicator is in the steady state “ON.”

Remote Control Mode:

The indicator is lit once emission is enabled.

6 Front Bezel Panel Pull on each side to filter element for cleaning or replacement. Refer
to Table B-1 on page B-2 for more information.

Figure 2-3 shows the front panel of the YLR-Series, which does not include a display.
Table 2-4 lists details for each component.

2-4
 Using Your Device
YLR Series — Front Panel View

Figure 2-3. Front Panel View without Display

Figure 2-4. Front Panel Descriptions

Item Feature Description

1 Power When lit, indicates that internal main power supply of the laser is on.

When the indicator is on, the internal power supply is active and the
laser is capable of producing laser radiation.

2 PS Active When lit, indicates that the main supply voltage is applied to the laser
module inside the device.

3 Emission When lit, indicates that the emission is activated.

4 Error When lit, indicates an device error, such as a interlock door is open.

5 Front Bezel Panel Pull on each side to filter element for cleaning or replacement. Refer
to Table B-1 on page B-2 for more information.

2-5
Using Your Device
YLR Series — Rear Panel View

YLR Series — Rear Panel View

The YLR-Series is available as a Water-Cooled (WC) or Air-Cooled (AC) laser.
Figure 2-5 shows details of the rear panel of the YLR-Series WC laser. Table 2-4
lists details for each component.
Figure 2-5. Rear Panel View - WC Laser

Table 2-4. Rear Panel Descriptions

Item Feature Description

1 Laser Output The output of the laser (fiber cable) is delivered through this location.

2 Hardwiring Interface (24-pin) The 24-pin connector provides an analog and digital interface for
hardwiring control of the laser. See Table 2-5 on page 2-14 for
detailed information.

3 Hardwiring Interface (7-pin) The 7-pin connector provides status of the power supply and front
panel Emergency Stop (if present). See Table 2-8 on page 2-23 for
detailed information.

4 Ethernet Ethernet port

2-6
 Using Your Device
YLR Series — Rear Panel View

Item Feature Description

5 AC line input The 3-pin screw terminal connector for AC input wiring.

Refer to the SPECIFICATION YTTERBIUM FIBER LASER

document included with this product to determine your models
power requirement.
6 AC line fuses Replaceable fuses F1, F2
Refer to Table B-1 on page B-2 for more information.

7 Coolant Inlet Liquid Coolant Input

Refer to the SPECIFICATION YTTERBIUM FIBER LASER

document included with this product for coolant details.

8 Coolant Outlet Liquid Coolant Output

Refer to the SPECIFICATION YTTERBIUM FIBER LASER

document included with this product for coolant details.

9 Drain Drain for the dehumidifier option.

Figure 2-6 shows details of the rear panel of the YLR-Series AC laser.
Table 2-5 lists details for each component.

2-7
Using Your Device
YLR Series — Rear Panel View

Figure 2-6. Rear Panel View - AC Laser

Table 2-5. Rear Panel Descriptions

Item Feature Description

1 Laser Output The output of the laser (fiber cable) is delivered through this location.

2 Hardwiring Interface (7-pin) The 7-pin connector provides status of the power supply and front
panel Emergency Stop (if present). See Table 2-8 on page 2-23 for
detailed information.

3 Hardwiring Interface (24-pin) The 24-pin connector provides an analog and digital interface for
hardwiring control of the laser. See Table 2-5 on page 2-14 for
detailed information.

4 Ethernet Ethernet port

5 AC line input The 3-pin screw terminal connector for AC input wiring.

Refer to the SPECIFICATION YTTERBIUM FIBER LASER

document included with this product to determine your models
power requirement.

6 AC line fuses Replaceable fuses F1, F2

Refer to Table B-1 on page B-2 for more information.

2-8
 Using Your Device
Optical Output Fiber Terminations

Optical Output Fiber Terminations

Products with a Connector
The end connector of the fiber (as shown in Figure 2-7) uses a protective cap that
covers and protects the optical surface and electrical contacts when not in use.
These protective caps must be removed from the connectors when connecting the
process fiber cable of the laser to an appropriate optical interface. You should remove
the protective caps from the connectors immediately before optical cleaning and
mounting in an adapter.
Figure 2-7. Optical Output Fiber Connector

2-9
Using Your Device
Model Specifications

Products with a Collimator

Collimators have a protective window that can be replaced if damaged (as shown in
Figure 2-8). You must remove the collimator end cap prior to use. This cap can be
re-used when storing the system. Cleaning of the protective window should be
performed as needed using the same materials and techniques described in “Optical
Fiber Connector Inspection and Cleaning” on page C-1.
Figure 2-8. Fiber End with Collimator

Model Specifications
Because the YLR-Series product line is extensive, all specifications for your specific
model are listed in the supplemental document titled SPECIFICATION YTTERBIUM
FIBER LASER included with the product. These specifications include:
• Optical
• Electrical
• Environmental
• External Layout and Dimensions

2-10
 Using Your Device
Unpacking Instructions

Unpacking Instructions

Note If the packaging shows any signs of external damage, check unit for damages and
notify the shipping agent immediately.
Particular care must be taken when you remove the unit from the packing case to
ensure that the fiber optic cable is not broken or damaged. A comprehensive packing
list is included with the system documentation.
Upon receipt of the laser, check all items against this list and contact IPG immediately
if any of the items are missing or if any damage to the unit is evident. If any damage
to the unit is evident or suspected, do not attempt to install or operate the laser in any
case.

CAUTION: Lift and carry the device by supporting the device from the base.
Use the handles (if available for your device) to help position the product while
it is properly supported. Do not use the handles for lifting or carrying the device.
Do not lift or position the device by any attached fibers or cables.

Laser models that are smaller and relatively lighter are packaged in foam insulated
cardboard boxes. See “Unpacking a Unit from a Cardboard Box” on page 2-11.
Laser models that are larger and relatively heavy are packaged in foam insulated
wooden crates. See “Unpacking a Unit from a Wooden Crates” on page 2-14.
To minimize the risk of damage to your system, IPG Photonics recommends that you
unpack your laser using the following procedures.

Unpacking a Unit from a Cardboard Box

See Figure 2-9 on page 2-13 for an illustration of this procedure.
To unpack your unit from a cardboard box:
1. Place the package on a stable surface such as the floor or a large table.
2. For international shipments, remove the external box to access the primary box.
3. Open the primary box and remove the foam cover and store for later use.
4. Place the fiber on top of the unit and carefully lift it out of the box. IPG strongly
recommends two people to lift the unit at all times.
5. Open the internal box and remove the top foam insert.

2-11
Using Your Device
Unpacking Instructions

6. Check the inventory of following items:

Shipping Box Contents Quantity

Cover, AC Power Inlet (P45-001394) 1

Strain Relief (P40-002294) 1

Strain Relief Nut (P40-002293) 1

Harting 24-pin Interface Connector Kit 1

(P30-007268)

Connector (P40-001344) 1

Hood (P40-001343) 1

Cable Seal (P40-000891) 1

Contact Pins (P40-000888) 16

Contact Pins (P40-000887) 10

Keys 2

Harting 7-pin Interface Connector (P30- 1

007305)

7. Retain all packaging for future transportation or storage needs.

2-12
 Using Your Device
Unpacking Instructions

Figure 2-9. Unpacking a Unit from a Cardboard Box

2-13
Using Your Device
Unpacking Instructions

Unpacking a Unit from a Wooden Crates

See Figure 2-10 on page 2-15 for an illustration of this procedure.
To unpack a unit from a wooden crate:
1. Place the package on a stable surface such as the floor or a large table. IPG
recommends using a powered screwdriver to remove all of the top screws
securing the top lid.
2. Remove the top lid and top foam insert.
3. Using a cutting tool remove the tie wraps securing the fiber to the second insert.
4. Place the fiber on top of the unit and carefully lift it out of the box. IPG strongly
recommends two people to lift the unit at all times.
5. Check the inventory of following items:

Shipping Box Contents Quantity

Cover, AC Power Inlet (P45-001394) 1

Strain Relief (P40-002294) 1

Strain Relief Nut (P40-002293) 1

Harting 24-pin Interface Connector Kit 1

(P30-007268)

Connector (P40-001344) 1

Hood (P40-001343) 1

Cable Seal (P40-000891) 1

Contact Pins (P40-000888) 16

Contact Pins (P40-000887) 10

Keys 2

Harting 7-pin Interface Connector (P30- 1

007305)

6. Retain all packaging for future transportation or storage needs.

2-14
 Using Your Device
Unpacking Instructions

Figure 2-10. Unpacking a Unit from a Wooden Crate

2-15
Using Your Device
Using the YLR-Series

Using the YLR-Series

CAUTION: Refer to the SPECIFICATION YTTERBIUM FIBER LASER

document included with this product for proper electrical power requirements.

Before switching the power on, ensure that the incoming AC voltage is equal to
the level noted in the specification.

Operate only in an environment with sufficient airflow capacity that allows for
the specified heat load developed during operation.

Connecting Electrical Power

Refer to the SPECIFICATION YTTERBIUM FIBER LASER document included with
this product to determine your models power requirements.

Note A power cord is not provided with the laser.

To connect the electrical power:

1. Wire the power input terminal block on the rear panel of the laser to the voltage,
phase and frequency indicated on the SPECIFICATION YTTERBIUM FIBER
LASER document for your particular model.
L2 = Line Voltage, PE = Protective Earth, L1 = Line Voltage
2. Cover the input power terminal block with the supplied cover.
3. Secure the cable with the supplied strain relief.
The electrical connection to the unit must be permanently connected to dedicated
AC mains with a circuit breaker that does not exceed 20 Amps. This must be in
close proximity to the unit and within easy reach of the operator and marked as
the disconnecting device for the unit.
4. Follow all national and local requirements when wiring to the unit.

2-16
 Using Your Device
Using the YLR-Series

Figure 2-11. Power Cord Connection

Interface Wire Specification

The minimum wire gage is 18AWG at 15 meters (30 meters maximum regardless of
gauge). The gage of the wire must increase as the distance increases. For connectivity,
the wiring and/or cabling must have an overall shield to ensure proper functionality.
The shield is to cover over all conductors and terminate at the unit where the
conductors enter/exit the unit.

Connections to External Circuits

Except for Mains connection, the external connections between this product and other
external devices are PELV (Protected Extra Low Voltage) as defined by IEC 61140.
Non-Mains outputs of other devices connected to this product should also be PELV
or SELV (Safety Extra Low Voltage).

2-17
Using Your Device
Using the YLR-Series

Interlock Safety Circuit

YLR lasers include an Interlock Safety Circuit that uses a dual-channel system with
monitored output and manual reset.
When you open the Interlock, the safety circuit opens and power to the laser diodes
is removed.
Follow these steps:
1. Close the dual channel interlock (on 24-pin connector: pin1 is connected with
pin4 and pin2 is connected with pin3). Otherwise, the internal main power
supply is switched off and the emission cannot be turned on.
Once any of the pairs of the mentioned above contacts is opened, you cannot
switch the lasers power supply on until the second pair is opened and then both
pairs are closed.
2. If you close the interlock (the Emergency Stop button is also released) and a
fault is not detected, press the Start button to connect the remote start contacts,
which enables the main power supply. The Power Supply (PS) Active signal
enters a high state and power is supplied to the laser module. The laser diodes
remain inactive until a separate Laser Enable signal transitions high and an
output power level set to a non-zero value.
The power to the laser diodes also turns on. However, under normal conditions
the diodes only turn on after emission is enabled.
When you open the interlock or a fault is detected, the laser diodes are discon-
nected from the main power supply. The Power Supply Active signal enters a
low state.
A detected fault is latched and circuits open the monitored manual reset loop,
thus preventing the laser from being restarted until the fault is addressed. If a
fault is detected, such as a shorted interlock channel, or a shorted Start button,
the safety circuit does not reset until the fault is corrected.
If the remote Start button is shorted (this is the equivalent of holding in the Start
button), the circuit does not reset when the interlocks are closed until the safety
circuit processes both channels open and then closed or the power to the safety
circuit is cycled (with the Start button in the opened state in both cases).

2-18
 Using Your Device
Using the YLR-Series

Interface Connector Pin Assignments

Table 2-6 provides electrical pin assignments for these Interlock Channels.
Table 2-6. 24-Pin Connector Pinouts
Pin Signal Name Signal Type Signal Signal Typical Description
Level Drive Response
Time
1 Interlock Ch1A Contact Closurea < 500 ms Emergency Shutdown
to pin 4 CW according to ISO 13849-1 Cat.3
<1.2 s PL d.b
2 Interlock Ch2A Contact Closurea QCW
to pin 3
— —
3 Interlock Ch2B Contact Closurea
to pin 2
4 Interlock Ch1B Contact Closurea
to pin 1
5 RS232 Tx Serial — — 120 ms Transmit Data
Communication
6 RS232 Rx Serial — — Receive Data
Communication
7 RS232 Com Return — — RS-232 Return
a
8 Remote Key Contact Closure — — 5s Activates the laser control
Switch electronics in Remote mode.
9
10 Remote Start Momentary — — 1s Activates the internal main
Button Contact Closurea power supply and connects it to
11 the laser module in Remote
mode.
12 Analog Input to Analog Input 1-10 1 mA 20 µs Analog Input 1-10 VDC =
Control Current VDC (sink) 10 – 100% Setpoint
13 Analog Output Analog Output 0-5 VDC 11 mA 20 µs Analog Output 0-4 VDC = 0 -
Power Monitor (source) Pnom.
14 Isolated Analog Return — — — Return for signals on pins 12,
Com 13.
15 Modulation + Digital Input 5 to 6 mA 20 µs 5 -24 VDC Input.
24 VDC (sink)

16 Modulation - Return — — Return for signal on pin 15.

c
17 Guide Control Digital Input 5 to 6 mA 120ms Positive edge turns On red
24 VDC (sink) guide laser in Remote Control
Mode.
Pin Signal Name Signal Type Signal Signal Typical Description
Level Drive Response
Time

2-19
Using Your Device
Using the YLR-Series

Table 2-6. 24-Pin Connector Pinouts

18d Emission Enable Digital Input 5 to 6 mA 120ms Positive edge activates
24 VDC (sink) emission in Remote Control
Mode.
19 Error/Ready Digital Output 24 VDC 100 mA 120 ms Low indicates a laser error.
(source)
20 System Return — — — Return for signals on pins 17-19,
Common 21-24.
21 Error Reset Digital Input 5 to 6 mA 120 ms Positive edge resets all
24 VDC (sink) resettable errors.
22 Power On Digital Output 24 VDC 100 mA 120 ms High indicates that key switch is
(source) turned on.
23 Power Supply Digital Output 24 VDC 100 mA 120 ms High indicates that the internal
Active (source) main power supply is active.
24 Emission ON Digital Output 24 VDC 100 mA 120 ms High at the emission is enabled.
(source)

a. Connection of potential free contacts only. External contact closure must be rated to > 1A /24
VDC.
b. To have a possibility of the internal main power supply activation, it is necessary to close the dual
channel interlock (pin1 is connected with pin4 and pin2 is connected with pin3). Otherwise, the
internal main power supply is switched off and the emission cannot be turned on. Once either of
these connection pairs is opened, it is impossible to switch the lasers power supply on until the
second pair is opened and then both pairs are closed.
c. To use this pin, external guide beam control must be enabled (EEABC command).
d. To use this pin, external emission control must be enabled (ELE command).

Note: Connector housing is EMC rated and is the intended connection point for the shielding of the
customer's cabling.

2-20
 Using Your Device
Using the YLR-Series

Table 2-7. 24-Pin Connector — Additional Details

Pin Signal Name Description

1 Interlock Ch1A These connections are intended to satisfy the Remote Interlock Connector
requirement as defined by 21 CFR 1040.10 (f)(3) and IEC 60825-1 (4.4). If the
2 Interlock Ch2A connections between pins 1-4 or 2-3 are breeched by a door interlock or other
3 Interlock Ch2B means, laser emission is prevented.

4 Interlock Ch1B
5 RS232 Tx —
6 RS232 Rx
7 RS232 Com —
8 Remote Key Intended for use when the laser product is integrated into an end-user system.
Switch
9
It is the responsibility of the purchaser/end-user to bring the end system into full
compliance with all applicable regulations.
10 Remote Start Intended for use when the laser product is integrated into an end-user system. It is
Button the responsibility of the purchaser/end-user to bring the end system into full
11 compliance with all applicable regulations.
12 Analog Input to Intended to control the level of laser output power with either Local or Remote
Control Current Control Mode enabled, power supply enabled, external emission control enabled
(Remote Control Mode only), and analog control enabled.

The output power is proportional to the analog voltage being supplied to the device.
IPG recommends the integrator sets the voltage on this pin to zero volts when the
emission, laser power supply, or the laser main power (VAC) is OFF.

IPG also recommends the integrator use a analog voltage source capable of
supplying a clean/stable signal. Suggested voltage sources might be in the form of
a PLC, Arbitrary Waveform Generator, or other similar products.
13 Analog Output —
Power Monitor
14 Isolated Analog —
Com
15 Modulation + Modulation mode must be enabled and can be used in either Local or Remote
Control modes of operation. Review the product specification for allowable
modulation settings specific to your product. Also, the modulation signal is not
intended to be used for functional safety or as a safety device.

IPG has incorporated a certified safety circuit for this purpose and it is the
responsibility of the purchaser/end-user to bring the end system into full compliance
with all applicable regulations.
16 Modulation - —
17 Guide Control —

2-21
Using Your Device
Using the YLR-Series

Pin Signal Name Description

18 Emission Enable Intended to control the level of laser output power with Remote Control Mode
enabled, power supply enabled, and external emission control enabled. The
emission enable signal is not intended to be used for functional safety or as a safety
device.

IPG has incorporated a certified safety circuit for this purpose and it is the
responsibility of the purchaser/end-user to bring the end system into full compliance
with all applicable regulations. Hardware Control must be set to enable in the laser
web interface.
19 Error/Ready —
20 System Common —
21 Error Reset —
22 Power On Intended to be used by the integrator for indicating the laser control system is turned
ON. The signal is active high when the local key is turned on or when the remote
key is turned on for models without the display option.

If Local Control Mode is ON or in the middle position and the remote key is ON, the
control system is OFF.

The integrator should use this signal to notify operators using the end product, that
the key has been turned on. It is the responsibility of the purchaser/end-user to
bring the end system into full compliance with all applicable regulations.
23 Power Supply Intended to be used by the integrator for indicating the power supply is activated.
Active The signal is available whether the laser is in Local Control or Remote Control
Mode. The integrator should use this signal to warn operators using the end product
that the power supply is active and the laser is capable of emitting laser radition.

Since the laser emission is delivered through an optical cable which might be tens
of meters in length. This signal is provided so proper warnings are made available
at the laser aperture and the remote control system as defined by the integrator. It
is the responsibility of the purchaser/end-user to bring the end system into full
compliance with all applicable regulations.
24 Emission ON Intended to be used by the integrator for indicating the laser emission is turned ON.
The signal is available whether the laser is in local or remote mode. The integrator
should use this signal to warn operators using the end product that emission is
turned ON and the product can be or is emitting laser radiation.

Since the laser emission is delivered through an optical cable which might be tens
of meters in length, this signal is provided so proper warnings are made available
at the laser aperture and remote control system as defined by the integration.

Note: The signal is active when the emission is turned ON and remains active even
if the laser output is set at “zero” and no actual laser emission is present. It is the
responsibility of the purchaser/end-user to bring the end system into full compliance
with all applicable regulations.

2-22
 Using Your Device
Using the YLR-Series

Table 2-8. 7-Pin Connector Pinouts

Pin Signal Name Signal Signal Signal Typical Description/Comments

Type Level Drive Response
Time
1 E-Stop Out Contact Direct connection to E-Stop
Channel 3A Closure to button on the front panel. If you
pin 3a press Emergency Stop on the
front panel, channels 3 and 4 are
2 E-Stop Out Contact open.
Channel 4A Closure to
pin 4a
Intended to be used by
3 E-Stop Out Contact integrators to shut down parts of
Channel 3B Closure to the system or entire system
pin 1a when the laser front panel E-
stop is activated. Only
4 E-Stop Out Contact applicable to laser option with
Channel 4B Closure to display and controls on the front
pin 2a panel.
5 PS_Active1 Digital 24 VDC <100mA 120 msb A high condition indicates that
Output (source) the internal main power supply
is active.

Redundant signal for indicating

the power supply has been
activated. The signal is available
whether the laser is in Local
Control or Remote Control
Mode.

The integrator should use this

signal to warn operators using
the end product, that the power
supply is active and capable of
emitting laser radiation. It is the
responsibility of the purchaser/
end-user to bring the end
system into full compliance with
all applicable regulations.
6 No Connection — — — —
7 Common Return — — — Return for signals on pins 5.

a. Contact closure components rated 24VDC, 1A.

b. Interlock response time (500 ms and 1.2s QCW models) must be additionally considered to
ensure the safe state of the device.

Note: Connector housing is EMC rated and is the intended connection point for the shielding for the
customer’s cabling.

2-23
Using Your Device
Using the YLR-Series

Initial Power-Up Sequence

CAUTION: All electrical connections (and water connections for Water-Cooled

models) must be connected prior to applying power to the unit.
In addition and where applicable, all connections must be secured with screws to
ensure proper functionality.

To initially power-up the system:

1. Ensure the E-Stop button on the front panel is pushed in.
2. Inspect the optical output end face to check for dust and debris (refer to “Optical
Fiber Connector Inspection and Cleaning” on page C-1 for more information).
3. Properly align the output fiber into the delivery optics.
4. Properly secure optical output collimator.

WARNING: Never look directly into a live fiber and ensure that you wear
appropriate laser safety eyewear at all times while operating the product. Ensure
all power is removed from the laser when handling the delivery cable.

5. Ensure the Interlock (pins 1 to 4, 2 to 3) on the interface connector is closed.

6. Release (pull out) the E-Stop button on the front panel and ensure that the
external E-Stop (from the 24-pin connector) is disengaged if used.
7. Ensure that the air-cooling vents are unobstructed to allow proper cooling of
the device.
8. Verify that the external cooling unit is powered on (for Water-Cooled models
only).

Key Control
You cannot turn on or operate the device until the key switch is in the ON or REM
position. ON or REM is only applicable to products with the Local Control option.
Products that do not have this option need to close the remote key circuit, pins 8 and
9 on remote connector (refer to Table 2-6 on page 2-19).
You cannot switch between ON and REM without moving position into OFF and
then waiting a few seconds.

2-24
 Using Your Device
Using the YLR-Series

YLR-Series System Operation

The YRL-Series system operation is illustrated in Figure 2-12.
Figure 2-12. YLR-Series Timing

2-25
Using Your Device
Using the YLR-Series

Rear Panel: 7-pin and 24-pin Connectors

There are two connectors on the rear panel of chassis: 7-pin and 24-pin. Figure 2-13
on page 2-27 shows the connections to 24-pin connector. Figure 2-14 on page 2-28
shows the connections to the 8-pin connector.
The two Interlock contacts ILK1 and ILK2 are connected between pins 1-4 and 2-3.
The Keyswitch is connected between pins 8 and 9. This switch should be closed to
power system up in Remote Control Mode. The Start button is connected between
pins 10 and 11. When closed it starts system in Remote Control Mode.
There is an isolated RS-232 interface (signals on pins 5 and 6 are referenced to return
on pin 7). Two isolated analog signals on pins 12 and 13 are referenced to analog
return on pin 14. Two differential modulation signals on pins 15 and 16 are also
isolated. The control and diagnostic signals on pins 17-19 and pins 21-24 are
referenced to return on pin 20 and are isolated.

2-26
 Using Your Device
Using the YLR-Series

Figure 2-13. 24-Pin Connector Interfaces

2-27
Using Your Device
Using the YLR-Series

Figure 2-14. 7-Pin Connector

Two contacts of the E-Stop button are connected between pins 1-4 and 2-3. When
you push the E-Stop button, these contacts become open. They return to closed state
when E-Stop button is released.
One isolated Power Supply Active signal on pins 5 is referenced to the return on
pin 7.

2-28
 Using Your Device
Using the YLR-Series

Operation Control Modes

There are two control modes for the laser: Local and Remote. You select these modes
using the Keyswitch on the front panel (see Figure 2-2 on page 2-3).
If the Keyswitch is in the ON position, the Local control mode is activated. If the
Keyswitch is in REM position, the Remote control mode is activated.
Table 2-9 details the differences between these two modes:

Table 2-9. Local and Remote Control Modes

Local Remote
(Keyswitch “ON” position (Keyswitch “REM” position)

Control Electronics Enabled Remote Laser Power Keyswitch

Enabling

Main Power Supply Start button Remote Start Button

Enabling

Emission Control RS-232, Ethernet, Hardware Emission Control Hardware Emission

Touch-screen Enableda Control Disabledb
External Interface RS-232, Ethernet

Guide Laser RS-232, Ethernet, External Aiming Beam Control External Aiming
Control Touch-screen Enabledc Beam Control
Disabledd

External Interface RS-232, Ethernet

Operation Mode RS-232, Ethernet, RS-232, Ethernet

Selection Touch-screen

a. Default Setting: To set “Hardware Emission Control Enabled” send the command "ELE" via RS-
232 interface or select it in setting menu using Touch Screen display.
b. To set “Hardware Emission Control Disabled” send the command “DLE” via the RS-232 interface
or change it in settings menu using Touch Screen display.
c. To set “External Aiming Beam Control Disabled” send the command “DEABC” via the RS-232
interface or change it in settings menu using Touch Screen display.
d. To set “External Aiming Beam Control Disabled” send the command “DEABC” via the RS-232
interface or change it in settings menu using Touch Screen display.

2-29
Using Your Device
Using the YLR-Series

Turning on the Device in Local Control Mode

To turn on the device in Local Control Mode:
1. Turn the front panel Keyswitch clockwise to the ON position.
2. Press the Start button to turn on the main power supply.
3. Wait until the laser becomes active.
The laser is now ready for operation. You can now select a proper operation
mode.

Turning on the Device in Remote Control Mode

To turn on the device in Remote Control Mode:
1. Turn the front panel Keyswitch counterclockwise to the REM position.
2. Close contact pins eight and nine to provide the remote keyswitch function.
3. Make momentary closure of pins 10 and 11 to activate the main power supply.
4. Turn the emission on. Refer to “Local and Remote Control Modes” on page
2-29.
5. Wait until the laser becomes active.
The laser is now ready for operation. You can now select a proper operation
mode.

2-30
 Using Your Device
Using the YLR-Series

Selecting Operation Modes

In both control modes (Local and Remote), there are two main modes of laser
emission:
• Continuous (CW)
• Pulsed (QCW)

Pulse Mode (QCW)

Pulse Mode (for QCW models only, Pulse-mode enabled) laser internally generates
a sequence of pulses. Pulse duration and pulse repetition rate can be configured by:
• Sending corresponding commands via RS-232 interface, or
• Using the Pulse Settings sub-menu on the touch-screen display
The main difference between Pulse and CW modes is that in Pulse Mode the
maximum peak power is considerably higher than in CW.
However, the maximum pulse duration and the maximum duty cycle are limited to
certain values (refer to the SPECIFICATION YTTERBIUM FIBER LASER document
and refer to Figure 2-15). When in CW mode, the maximum pulse duration and duty
cycle are not applicable.
Figure 2-15. Pulse (QCW) Operational Range

2-31
Using Your Device
Using the YLR-Series

Operational Sub-Modes
For each mode of laser emission (Continuous or Pulse), there are four operational
sub-modes:
• Standalone
• Modulation
• Gate
• External (Analog) Power Control
The main difference between sub-modes of operation is how the laser power is set
and the laser emission is switched on/off.
Continuous Mode (Pulse mode is disabled) laser generates CW emission (except for
Gate mode).

Standalone Mode (Modulation and Gate control disabled)

The value of pump LD current (controls output power) is controlled by:
• Sending a RS-232 command, or
• Sending an Ethernet command, or
• Using control buttons on the touch-screen (in Local Mode).

Modulation Mode
• The value of pump LD current is controlled as in the Standalone Mode.
• Laser emission is turned on/off by the user-generated “Modulation” signal applied to
pins 15-16 of External Interface Connector.

Gate Mode
• The value of pump LD current is controlled as in the Standalone Mode.
• Laser emission is controlled both, externally and internally . The user-generated
“Gate” signal applied to pins 15-16 of External Interface Connector starts and stops
internal generation of pulses.

External (Analog) Power Control

• The value of pump LD current value is controlled by the voltage applied between pins
12 and 14 of the External Interface Connector (see Table 2-5 on page 2-14 for more
information).
• Pulse sequence generation, modulation and gating are performed as in corresponding
modes above.

2-32
 Using Your Device
Using the YLR-Series

Pulse Shaper Program (Optional Feature)

• You can create and store arbitrary waveform pulses in the Pulse Profiles library.
• You can create and store Pulse sequences (combinations of pulse profiles, delays, and
repeats) in the Pulse Sequences library.
• Pulses can be started by Emission On command/signal (when Gate Mode is disabled)
or by the “Gate” signal applied to Pins 15-16 of External Interface Connector (when
Gate Mode is enabled).
• You cannot select Waveform Mode if either External (Analog) Control or Modulation
Mode is enabled.
See “Pulse Shaping” on page 4-1 for details on using the Pulse Shaper program.

Using the Touch-Screen Display

You can use the touch-screen display on the front panel for manual control of the
device. You can view information about the device’s state and settings. In addition,
activating certain commands from the main window invokes additional submenu
windows. In Remote Mode, the touch-screen display function is disabled and can
only be used for display purposes.

2-33
Using Your Device
Using the YLR-Series

Figure 2-16. Main Menu Screen

2-34
 Using Your Device
Using the YLR-Series

Table 2-10. Main Menu Descriptions for Touch-Screen Display

Item Description

1 Model Name.

2 Power Indication/Setting:
Touching this field displays the Setpoint window where you can enter the required setpoint
value.

3 When active (inactive shown) indicates that the analog (external) power control is enabled or
in Pulse Waveform Mode.

4 When active, shows that the main supply voltage is applied to the laser module inside the
device.

5 Indicates the state of the emission control: “Internal” (hardware control disabled) or “External”
(hardware control enabled).

6 Touching this button turns the guide laser ON or OFF.

7 Touch this button to activate or deactivate the emission.

8 IP address indication/setting. Touching this field opens the window where you assign an IP
address to the system.

9 Internal Temperature display.

10 When active, indicates that the Modulation or Gate Mode is enabled.

11 Indicates the current operational state: Local or Remote.

12 Indicates the state of the guide laser control: Internal or External.

13 Setpoint Bar: Touch Set and drag your finger up or down to set the required value. Press Lock
when finished.

2-35
Using Your Device
Using the YLR-Series

Figure 2-17. Sub-Menus Screen

2-36
 Using Your Device
Using the YLR-Series

Table 2-11. Sub-Menus Descriptions

Item Description

1 Current Power setpoint value (in percentage) of maximum power (for example, 12%).

2 Enter the Power setpoint in percentage of the maximum power.

3 Accept new Power setpoint.

4 Return to the previous screen.

5 Power setpoint value in percentage of maximum power (for example, 57.5%).

6 Power Control Bar (disabled when locked).

7 Press Lock to unlock the Power Control Bar function (“Set” is displayed).

8 Press Set to change the power to the new setpoint and lock the Power Control Bar.

9 Press to turn on the Guide Beam. A Green dot lights up

2-37
Using Your Device
Using the YLR-Series

Figure 2-18. Sub-Menus Screen

2-38
 Using Your Device
Using the YLR-Series

Table 2-12. Sub-Menus Descriptions

Item Description

1 Press the Emission Button and you are asked to confirm the emission startup process by
pressing OK. Press Cancel to exit.

2 Press the IP address box to enter a new IP address.

3 Press the Net Mask box to enter a new net mask address.

4 Press the Web Access Code box to enter a new web access address.

5 Press Return to go back to the previous screen.

6 Opens the Pulse Settings menu (function described lower in table).

7 Enable or Disable the Gate mode

8 Enable or Disable the External Guide Laser control.

9 Enable or Disable the External Analog Power control.

10 Return to the previous screen.

11 Enable or Disable the Emission Control mode.

12 Enable or Disable the Modulation mode.

2-39
Using Your Device
Using the YLR-Series

Figure 2-19. Sub-Menus Screen

2-40
 Using Your Device
Using the YLR-Series

Table 2-13. Sub-Menus Descriptions

Item Description

1 Opens Pulse Mode sub-menu.

2 Opens Waveform Mode sub-menu.

3 Return to the previous screen.

4 Enables or Disables the Waveform Pulse Mode.

5 Single Pulse/Pulse Sequence.

6 Use the Up/Down Arrows to scroll to select a program from memory.

7 Selected the program in memory.

8 Transfers the selected program to the laser.

2-41
Using Your Device
Using the YLR-Series

Figure 2-20. Sub-Menus Screen

2-42
 Using Your Device
Using the YLR-Series

Table 2-14. Sub-Menus Descriptions

Item Description

1 Pulse Program Information Screen. Clicking anywhere in this area displays the Preview
Screen.

2 Use the Up and Down arrows to scroll to select a program from memory.

3 Return to the previous screen.

4 Pulse Program Preview screen.

5 Use the Up and Down arrows to scroll to select a program from memory.

6 Return to the previous screen.

2-43
Using Your Device
Using the YLR-Series

Figure 2-21. Sub-Menus Screen

2-44
 Using Your Device
Using the YLR-Series

Table 2-15. Sub-Menus Descriptions

Item Description

1 Toggles between the Continuous (CW) and Pulsed (QCW) modes.

2 Opens Pulse Width dialog.

3 Opens Pulse Width dialog.

4 Return to the previous screen.

5 Enter Pulse Width in milliseconds (ms) range is 0.2 to 20 ms in .05 ms increments.

6 Accept the Pulse Width.

7 Cancel and return to the previous screen.

8 Enter Repetition Rate in Hertz (Hz) range is 1 to 5000 Hz in 1 Hz increments.

9 Accept the Repetition Rate.

10 Cancel and return to the previous screen.

2-45
Using Your Device
Using the YLR-Series

2-46
 3

Computer Interface/Commands
RS-232 Configuration
A three-wire (RxD, TxD, GND) interface is used (null modem cable). The individual
commands are described in “Interface Commands” on page 3-2. See “Interface
Connector Pin Assignments” on page 2-19 for details on 24-pin interface
connectivity.
The RS-232 interface is configured with the following parameters:

Table 3-1. RS-232 Parameters

Parameter Value

Baud Rate 57,600

Data Bits 8

Stop Bits 1

Parity None

Flow Control None

Ethernet TCP/IP Interface

The IP address of the laser is shown on the front panel. Touching the screen where
the address is shown displays the network setup menu where you can change the
network settings.
The laser listens for connections on port 10001. The command must be sent as a
single string in a single packet. The individual commands are described in “Interface
Commands” on page 3-2.

Table 3-2. Ethernet Interface Pinouts

Pin Description Notes

1 TX+ Transmit Data +

2 TX- Transmit Data -

3 RX+ Receive Data +

4 N/C Not Connected

3-1
Computer Interface/Commands

Pin Description Notes

5 N/C Not Connected

6 RX- Receive Data -

7 N/C Not Connected

8 N/C Not Connected

Interface Commands
All commands and responses consist of printable ASCII characters. Commands are
typically three or four letter mnemonic codes followed by a parameter, if required.
All commands and responses are terminated with a <Carriage Return> (CR, 0x0D,
\r) character If a CR terminated string is received, but a valid command is not found,
a response of "BCMD" is sent.
The commands are shown in Table 3-3, “Interface Commands” as all uppercase for
clarity; the actual commands are not case sensitive. A space character is also shown
between the command and parameter for clarity. The space is not required.
Every command generates a response. The responses generally consist of the
command echoed back. If there is a returned value, it is separated from the echoed
command by a ':' character.

Table 3-3. Interface Commands

Code Description Example

ABN Aiming Beam ON Sent: “ANB”

Response: “ABN”

“ERR: Cannot enable guide beam

because external guide control is
enabled.”

ABF Aiming Beam OFF Sent: “ABF”

Response: “ABF”

“ERR: Cannot disable guide

beam because external guide
control is enabled.”

DEABC Disable External Aiming Beam Control —Disables Sent: “DEABC”

hardware aiming beam control. Response: “DEABC”

3-2
 Computer Interface/Commands

Code Description Example

DEC Disable External Control — Disables the analog current Sent:”DEC””

control input. Response: “DEC” or
“ERR: Emission is ON!”
Disables Dynamic Scaling in Waveform mode.a
DGM Disable Gate Mode — Disables internal pulse generator. Sent: ”DGM”
Response: “DGM” or
“ERR: Emission is ON!”

DLE Disable Hardware Emission Control — Disables Sent: “DLE””

hardware emission control. Response: “DLE” or
“ERR: Emission is ON!”

DMOD Disable Modulation — Disables the modulation mode. Sent: “DMOD””

Response: “DMOD” or
“ERR: Emission is ON!”

DPMb Disable PULSE Mode — Disables PULSE mode. Sent: “DPM”

Response: “DPM” or
“ERR: Emission is ON!”

EEABC Enable External Aiming Beam Control - Enables Sent: “EEABC”

hardware aiming beam control. Response: “EEABC”

EEC Enable External Control — Enables the analog current Sent: “EEC”
control input. Response: “EEC” or
“ERR: Emission is ON!”
Enables Dynamic Scaling in Waveform mode.a

EGM Enable Gate Mode — Enables internal pulse generator Sent: “EGM”
gated by signal applied to modulation input. Response: ”EGM” or
“ERR: Emission is ON!”

ELE Enable Hardware Emission Control — Enables hardware Sent: “ELE”

emission control. Response: “ELE” or
“ERR: Emission is ON!”

EMOD Enable Modulation – Enables the modulation mode. Sent: “EMOD”

Response: “EMOD” or
“ERR: Emission is ON!”

EMOFF Stop Emission – Stops emission. Sent:: “EMOFF””

Response: “EMOFF” or
“ERR: Emission is ON!”

EMON Start Emission – Starts emission. Sent: “EMON”

Response: “EMON”

EPMb Enable Pulse Mode — Enables Pulse mode. Sent: “EPM”

Response: “EPM”

3-3
Computer Interface/Commands

Code Description Example

ESTA Read Extended Device Status — The extended status is Sent: “ESTA”
reported as a number of bit-encoded 32-bit words. The Response: “ESTA:
response contains the information required by IPG for 256;0;0;0;0;0;0;0;46;3”
remote troubleshooting.

LFPc Lock Front Panel – Locks touch-screen display on the Sent:: “LFP”
front panel of the laser. Response: “LFP” or
“ERR: Emission is ON!”

HELP In case of no parameters returns the list of applicable Sent: “HELP”

commands. In case of a specified command name as a Response: “Commands:
parameter returns the command description. STA
ROP
RPP
RCT
EMON
EMOFF
RET
…
RIP
SIP
RMASK
SMASK
RBAUD
SBAUD
HELP

Done
HELP

<Command> for more

information on a specific
command”

Sent: “HELP RPP”

Response: “HELP: RPP - Read
Peak Power”

Sent: “HELP RCD”

Response: “HELP: RCD -
Command Not Listed”

3-4
 Computer Interface/Commands

Code Description Example

RBAUD Read Baud Rate — Reads the current RS-232 baud rate. Sent: “RBAUD”
The response is the command echoed back, followed by Response “RBAUD: 8”
a delimiter of “: “ and then the communication speed
index (see below).

Index Speed (bits/s)

0 - 110
1 - 300
2 - 1200
3 - 2400
4 - 4800
5 - 9600
6 - 19200
7 - 38400
8 - 57600 default
9 - 115200

RCE Reset Critical Error — Followed by the code received Sent: “RCE 1123456123”
from IPG clears critical errors. Response: “RCE: Code
Accepted” or
“ERR: Code Incorrect”

RCS Read Current Setpoint — Reads the setpoint for the LD Sent: “RCS”
current. The response is the command echoed back, Response: “RCS: 56.7”
followed by a delimiter of “: : and then the current setpoint (Indicates that the LD current
in %. setpoint is 56.7%)

RCT Read Laser Temperature – Reads the internal Sent: “RCT”

temperature of the laser. The response is an echo of the Response: “RCT: 34.5”
command, a delimiter of “: “, and the temperature in
degrees centigrade.

REC Read Error Counter — Reads critical error counter. Sent: “REC”
Response: “REC: 37”

RERR Reset Errors — Resets any resettable errors. Sent “RERR”

Response: “RERR”

RET Read Elapsed Time — Reads the elapsed time the laser Sent “RET”
has been ON. The time is returned in minutes. Response: “RET: 1105”

RFV Read current software revision. Sent: “RFV”

Response: “RFV: 7.28;2.83;ND”
RMEC Read Module Error Code. Returns error code stored in Sent: “RMEC”
the laser or zero if normal operation. Response: “RMEC: 0”

RNC Read Minimum Current Setpoint — Reads the minimum Sent: “RNC”
current setpoint that can be set in the laser. The response Response: “RNC: 10.0”
is the command echoed back, followed by a delimiter of (Indicates that the minimum
“: “ and then the minimum current as a percentage of the setpoint is 10.0 %)
maximum.

3-5
Computer Interface/Commands

Code Description Example

ROP Read Output Power — Reads the output power in watts. Sent: “ROP”
The response is the command echoed back, a delimiter, Response: “ROP: 99.6”
and then either the power in watts “Off” if the emission is (Indicates that the output power is
off, or “Low” if the power is below the reliable 99.6 watts)
measurement threshold of the laser.
Sent: “ROP”
Response: “ROP: Off”
(Indicates that emission is off.)

RPP Read Peak Power — Reads the output peak power in Sent: “RPP”
Watts. The response will be the command echoed back, Response: “RPP:730”
a delimiter, and then either the power in watts “Off” if the (Indicates that the output peak
emission is off, or “Low” if the power is below the reliable power is 730 watts.)
measurement threshold of the laser.
Sent: “RPP”
Response: “RPP: Off”
(Indicates that emission is off.

Sent: “RPP”
Response: “RPP: Low”
(Indicates that the output power is
below the accurate measurement
range of the laser.)

RPRR Read Pulse Repetition Rate — Reads the pulse Sent: “RPRR”
repetition rate of the internal pulse generator. The Response: “RPRR: 10.00”
response is the command echoed back, followed by a (Indicates that the PRR is 10 Hz.)
delimiter of “:” and then the pulse width in Hz.

RPW Read Pulse Width — Reads the pulse width of the Sent: “RPW”
internal pulse generator. The response is the command Response: “RPW: 5.550”
echoed back, followed by a delimiter of “:”and then the (Indicates that the pulse width is
pulse width in ms. 5.55 ms.)

RSN Read Serial Number — Reads the serial number of the Sent: “RSN”
device. Response: “RSN: 6103081“

3-6
 Computer Interface/Commands

Code Description Example

SBAUD Set Baud Rate — Followed by an index (see below) sets Sent: “SBAUD 9”
RS-232 baud rate. The command sent via RS-232 has Response (Ethernet only):
no response and the communication speed is changed “BAUD: 9” or
just after receiving the command. The response to the “ERR: Invalid Baud Setting. Valid
command sent via Ethernet is the command echoed Settings = []
back, followed by a delimiter of “: “and then the
communication speed index. [0:110]
[1:300]
Index Speed (bits/s) [2:1200]
0 - 110 [3:2400]
1 - 300 [4:4800]
2 - 1200 [5:9600]
3 - 2400 [6:19200]
4 - 4800 [7:38400]
5 - 9600 [8:57600]
6 - 19200 [9:115200]
7 - 38400 [END]”
8 - 57600 default
9 - 115200 or “ERR: Emission is ON!”

SDC Set Diode Current — Sets the diode current. The units Sent: “SDC 34.2”
are in percent of maximum current. The setpoint must be Response: “SDC: 34.2”
below 100% and above the minimum current setpoint. (Current Setpoint is set to 34.2%.)

The current can also be set to 0. The response from the Sent: “SDC 104.2”
laser is the command echoed back, a delimiter of “:” and Response: “ERR: Argument out
then the current setpoint for the laser. A value that is of range”
outside the acceptable range will receive a response of (The setpoint is unchanged.)
“ERR: Out of Range.”
Sent: “SDC 34.2”
Response: “ERR: External
control enabled”
(The setpoint is unchanged.)

SPRR Set Pulse Repetition Rate — Sets the pulse repetition Sent: “SPRR 10”
rate. The units are in Hz. The pulse width and the duty Response: “SPRR: 10”
cycle (dependent on the pulse width and pulse repetition (PRR is set to 10 Hz.)
rate) must be within the specified range. The response
from the laser is the command echoed back, a delimiter Sent: “SPRR 100”
of “:” and then the pulse repetition rate.
Response: “ERR: Duty cycle too
high”
A value that is outside the acceptable range receives a (PRR is unchanged.)
response of “ERR: Duty cycle too high” or “ERR:
Frequency out of range.”
Sent: “SPRR 100000”
Response: “ERR: Argument out
of range”
(PRR is unchanged.)

3-7
Computer Interface/Commands

Code Description Example

SPW Set Pulse Width — Sets the pulse width. The units are Sent: “SPW 5.5”
in ms. The pulse width and the duty cycle (dependent on Response: “SPW: 5.5”
the pulse width and pulse repetition rate) must be within (Pulse Width is set to 5.5 ms.)
the specified range. The response from the laser is the
command echoed back, a delimiter of “:” and then the Sent: “SPW 11000”
pulse width.
Response: “ERR: Argument out
of range.”
A value that is outside the acceptable range receives a (The pulse width is unchanged.)
response of “ERR: Out of range” or “ERR: Duty cycle too
high.”
Sent: “SPW 8”
Response: “ERR: Duty cycle too
high.”
(The pulse width is unchanged.)

STA Read device status — The status is reported as a bit- Sent: “STA”
encoded 32-bit word. Undefined bits or bits defined as Response: “STA: 4100”
“Reserved” can be in any state and should be ignored.
This translates to the following:
Note: Each of the bits have a meaning as listed in Table
3-4 on page 3-9. 4100 = 0x1004, so bits 2 and 12
are set. This means that emission
is on and modulation is enabled.

SIP Set IP — Followed by a number in dot-decimal notation Sent: “SIP 10.0.0.2”

sets the IP address for the laser. Response: “SIP: 10.0.0.2”

SQSEL Select Sequence — Selects Pulse Sequence Mode and Sent: “SQSEL 5”
Pulse Sequence ID. If the command is not followed by Response: “New setting applied.
the ID number or the ID is invalid, then the existing (or Waveform Mode: Pulse
last) selection is used. Sequence Selected Sequence:
ID[5] – Name[Test1]”
Note: It is not possible to switch to sequence mode if
Waveform mode is enabled and no sequences exist. An
error is returned if that is the case. If the Key Switch is in
the Remote position, a waveform configuration is
automatically executed before a response is returned.

UFP Unlock Front Panel — Unlocks touch-screen display on Sent: “UFP”

the front panel of the laser. Response: “UFP” or

“BCMD” in case of key is in

REMOTE position” or

“Emission is ON!”

a. Lasers with Pulse Shaping option only.

b. QCW Models only.
c. Laser with Touch-Screen Display only.

3-8
 Computer Interface/Commands

Table 3-4. Bit Meanings

Bit 0 - 0 = Normal Operation

- 1 = Command Buffer Overload

Bit 1 - 0 = Normal Operation

- 1 = Overheat

Bit 2 - 0 = Emission Off

- 1 = Emission On

Bit 3 - 0 = Back Reflection OK

- 1 = High Back Reflection Level

Bit 4 - 0 = Analog Power Control Disabled

- 1 = Analog Power Control Enabled

Bit 5a - 0 = Normal Operation

- 1 = Pulse Too Long

Bit 6 - Reserved

Bit 7 - Reserved

Bit 8 - 0 = Aiming Beam OFF

- 1 = Aiming Beam ON

Bit 9 - 0 = Normal Operation

- 1 = Pulse too Short

Bit 10a - 0 = CW Mode

- 1 = Pulsed Mode

Bit 11 - 0 = Power Supply ON

- 1 = Power Supply OFF

Bit 12 - 0 = Modulation Disabled

- 1 = Modulation Enabled

Bit 13 - Reserved

Bit 14 - Reserved

Bit 15b - 0 = Emission is out of the 3 second start-up state.

- 1 = Emission is in the 3 second start-up state.

3-9
Computer Interface/Commands

(in ON position of the Keyswitch only)

Bit 16 - 0 = Gate Mode Disabled

- 1 = Gate Mode Enabled
a
Bit 17 - 0 = Normal Operation

- 1 = High Pulse Energy

Bit 18 - 0 = Hardware Emission Control Disabled

- 1 = Hardware Emission Control Enabled

Bit 19 - 0 = Normal Operation

- 1 = Power Supply Failure

b
Bit 20 - 0 = Front Panel Display is Unlocked

- 1 = Front Panel Display is Locked

Bit 21b - 0 = Keyswitch is in ON position

- 1 = Keyswitch is in REM position

Bit 22c - 0 = Waveform Pulse Mode OFF

- 1 = Waveform Pulse Mode ON

Bit 23a - 0 = Normal Operation

- 1 = Duty Cycle Too High

Bit 24 - 0 = Normal Operation

- 1 = Low Temperature

Bit 25 - 0 = Normal Operation

- 1 = Power Supply Alarm

Bit 26 - Reserved

Bit 27 - 0 = Hardware Aiming Beam Control Disabled

- 1 = Hardware Aiming Beam Control Enabled

Bit 28 - Reserved

Bit 29 - 0 = Normal Operation

- 1 = Critical Error

Bit 30 - 0 = Fiber Interlock OK

- 1 = Fiber Interlock Active

3-10
 Computer Interface/Commands

Bit 31a - 0 = Normal Operation

- 1 = High Average Power

a. QCW Models only.

b. Lasers with Touch-Screen Display only.
c. Lasers with Pulse Shaping Option only.

Table 3-5. TCP-IP Configuration Commands

Code Description Example

DDHCP Disable DHCP - Disables DHCP client Sent: “DDHCP”

Response: “DDHCP” or
“ERR: Emission is ON!”

EDHCP Enable DHCP - Enables DHCP client. Sent: “EDHCP”

Response: “EDHCP” or
“ERR: Emission is ON!”

RDGW Read Default Gateway — Reads the current default Sent: “RDGW”
gateway of the device. The response is the command Response: “RDGW: 192.168.1.1”
echoed back, followed by a delimiter of “: “ and then the
default gateway in dot-decimal notation.

RDHCP Read DHCP — Reads the current status of DHCP client Sent: “RDHCP”
function. The response is the command echoed back, Response: “RDHCP: OFF”
followed by a delimiter of “: “and then either “ON” or
“OFF.”

RIP Read IP —Reads the current IP address of the device. Sent: "RIP"
The response is the command echoed back, followed by Response: "RIP: 192.168.1.230"
a delimiter of “:” and then the IP address in dot-decimal
notation.

RLHN Read Local Host Name — Reads the current local host Sent: “RLHN”
name of the device. The response is the command Response: “RLHN: IPG-
echoed back, followed by a delimiter of “:” and then the 12004020”
name.
RMAC Read MAC Address — Reads the current MAC address Sent: “RMAC”
of the laser. The response is the command echoed back, Response: “RMAC: A1-B2-C3-
followed by a delimiter of “:” and then the MAC address D4-E5-F6”
in a form of six groups of two hexadecimal digits,
separated by hyphens (-).

RMASK Read Subnet Mask — Reads the current subnet mask of Sent: “RMASK”
the device. The response is the command echoed back, Response: “RMASK:
followed by a delimiter of “:” and then the subnet mask in 255.255.240.0”
dot-decimal notation.

3-11
Computer Interface/Commands

Code Description Example

RSTIP Reset TCP/IP Settings - Resets the settings to the default Sent: “RSTIP”
ones: Response: “RSTIP” or
“ERR: Emission is ON!”
DHCP client OFF
IP Address: 192.168.3.230
Default Gateway: 192.168.0.1
Subnet Mask: 255.255.240.0
Local Host Name: IPG-”serial number”
SDGW Set Default Gateway — Followed by a number in dot- Sent: “SDGW 192.168.0.1”
decimal notation sets the default gateway for the laser. Response: “SDGW: 192.168.0.1”
or
“ERR: Emission is ON!”

SIP Set IP — Followed by a number in dot-decimal notation Sent: “SIP 192.168.1.231”

sets the IP address for the laser. Response: “SIP: 192.168.1.231”
or
“ERR: Emission is ON!”

SMAC Set MAC Address — Followed by six groups of two Sent: “SMAC 12-34-56-78-EF-
hexadecimal digits, separated by hyphens (-), sets the EF”
MAC address for the laser. Response: “SMAC: 12-34-56-78-
EF-EF" or "ERR: Emission is
ON!”
SMASK Set Subnet Mask - Followed by a number in dot-decimal Sent: “SMASK 255.255.0.0”
notation sets the subnet mask for the laser. Response: “SMASK:
255.255.0.0" or
"ERR: Emission is ON!”

SLHN Set Local Host Name — Specifies the name of the device Sent: “SLHN IPG-12004020”
within the network. Response: “SLHN: IPG-
12004020” or “ERR: Emission is
ON!”

3-12
 Computer Interface/Commands

The following commands in Table 3-6 are for lasers with the Pulse Shaping option
only.

Table 3-6. Waveform Mode (Pulse Shaping) Specific Commands

Code Description Example

DWPM Disable Waveform Pulse Mode — Disables internal Sent: “DWPM”

arbitrary waveform generator (pulse shaping). Response: “DWPM” or
“ERR: Emission is ON!”

EWPM Enable Waveform Pulse Mode -— Enables internal Sent: “EWPM”

arbitrary waveform generator (Pulse Shaping). Response: “EWPM”
or
“ERR: No pulses available,
cannot enable waveform mode.”
or
“ERR: No sequences available,
cannot enable waveform mode.”
or
“ERR: Emission is ON!”
or
“ERR: Laser is not in Pulse
Mode!”

PCFG Configure Waveform Mode — Returns the status of the Sent: “PCFG”
Waveform Mode and the ID number of the selected Pulse Response: “PCFG: []
Profile or Pulse Sequence. [Status:Disabled]
[Mode:Profile]
[ID:2]
[END]”
PRLS Profile List — Displays a list of available Pulse Profiles Sent: “PRLS”
stored in the device library. Response: “PRLS: []
[0:New Shape 0]
[2:New Shape 2]
[END]”

PRSEL Select Profile — Selects Single Pulse Mode and Pulse Sent: “PRSEL 2”
Profile ID. If the command is not followed by the ID Response: "PRSEL: [2:New
number or the ID is invalid, then the existing selection is Shape 2]”
used. or
“ERR: Entered pulse ID is not
valid”
or
“ERR: No pulses are available”

SQLS Sequence List — Displays a list of available Pulse Sent: “SQLS”

Sequence programs stored in the device library. Response: “SQLS: []
[0:New Program 0]
[4:New Program 4]
[END]”

3-13
Computer Interface/Commands

Code Description Example

SQSEL Select Sequence - Selects Pulse Sequence Mode and Sent: “SQSEL 4”
Pulse Sequence ID. If the command is not followed by Response: “SQSEL: [4:New
the ID number or the ID is invalid, then the existing (or Program 4]”
last) selection is used. or
“ERR: Entered sequence ID is not
valid”
or
“ERR: No sequences are
available”

3-14
 4

Pulse Shaping
Overview
The Pulse Shaper program lets you sketch pulse points. It automatically fills in pulse
(power level) lines, and computes all the emission pulse characteristics
simultaneously. It also performs auto-correction in case constraints are violated.
A laser emission pulse is a custom time-based emission power signal, constrained by
an output sample time, maximum power, maximum energy and minimum current
(power) threshold, all of which are pre-configured in the laser.
Pulses are not zeroed visually when they go under the power threshold, although that
is not reflected in the pulse energy calculation.
To avoid pulse energy limits, either shorten your pulse widths or reduce the value of
the Time Scale.
Each time you change a Pulse Shape profile, the pulse widths are updated to reflect
the current sketched pulse. You cannot exceed the limits established in the laser
configuration.
You can create effective Pulse Shapes to meet the changing requirements of your
applications. You can store Pulse Shapes in a Pulse Profiles library on the laser or
locally to your computer. You can also create and store Pulse Sequences
(combinations of pulse profiles, delays, and repeats) in a Pulse Sequences library or
locally to your computer.
Figure 4-1 shows the Pulse Shaper interface.

4-1
Pulse Shaping
Overview

Figure 4-1. Pulse Shaper Interface

PC Requirements
The following minimum requirements are necessary for installing and using the Pulse
Shaping software:
• x86 machine with at least 512 MB RAM, 5 GB hard disk, mouse and keyboard, VGA
monitor and a Ethernet or Serial (RS-232) communication port
• Operating System: Windows 7
• Software: MS .NET Framework, Version 4.5
• Pulse Shaping program: Designated release version executable

4-2
 Pulse Shaping
Overview

Ethernet TCP/IP Interface

See “Ethernet TCP/IP Interface” on page 3-1 for details on the Ethernet Interface.
See Table 3-2 on page 3-1 for a list of Ethernet Interface pinouts.

RS-232 Configuration
See “RS-232 Configuration” on page 3-1 for details on RS-232 configuration.
See Table 3-1 on page 3-1 for a list of RS-232 parameters.

Key Terms
• Shape Editor — Lets you create and edit various Pulse Shapes and save them in the
Pulse library.
• Sequence Editor — Lets you create a sequence of pulses (pulse train) using Pulse
Shapes from Pulse library.
• Scaling Editor — Lets you scale pulses within a sequence (ramp up and down).
• Waveform — A waveform is the shape and form of a signal.

4-3
Pulse Shaping
Installing the Pulse Shaper Software

Installing the Pulse Shaper Software

To install the software package, run the Pulse Shaper Setup, which creates a folder
with the Pulse Shaper program.
To install the Pulse Shaper software:
1. Run the PulseShaper Setup.exe and select a language. The PulseShaper Setup
Wizard appears as shown in Figure 4-2.
Figure 4-2. PulseShaper Setup Wizard

2. Click Next to continue.

3. Select a destination location or accept the default location for the installation
as shown in Figure 4-3 and click Next.

4-4
 Pulse Shaping
Installing the Pulse Shaper Software

Figure 4-3. PulseShaper Setup - Location Destination

4. Click Next to accept the default Start Menu folder for the Pulse Shaper shortcut.
a. Click Browse if you want to change the default Start menu to another
location.
b. Click the Don’t create a Start Menu folder checkbox to skip this step.

4-5
Pulse Shaping
Installing the Pulse Shaper Software

Figure 4-4. PulseShaper Setup - Program Shortcut

5. Click Next to create a PulseShaper icon on your desktop (default) as shown in

Figure 4-5.
a. Deselect the Create a desktop icon checkbox if you want to skip this step.

4-6
 Pulse Shaping
Installing the Pulse Shaper Software

Figure 4-5. PulseShaper Setup - Desktop Icon

6. Click Install to continue with installation as shown in Figure 4-6.

Figure 4-6. PulseShaper Setup - Ready to Install

4-7
Pulse Shaping
Installing the Pulse Shaper Software

7. Click Finish to exit Setup as shown in Figure 4-7. By default, the Pulse Shaper
program launches when you exit Setup.
a. Deselect the Launch PulseShaper checkbox if you do not want Pulse
Shaper to launch upon exiting Setup.
Figure 4-7. PulseShaper Setup - Finish

4-8
 Pulse Shaping
Installing the Pulse Shaper Software

Configuring a Local Area Connection for Ethernet

To configure a local area connection for Ethernet:
1. Go to Control Panel -> Network and Internet -> Network and Sharing Center.
2. Click Change adapter settings.
3. Select a Local Area Connection icon. The following window appears as shown
in Figure 4-8.
Figure 4-8. Local Area Connection Status

4. Click Properties. The following window appears as shown in Figure 4-9.

4-9
Pulse Shaping
Installing the Pulse Shaper Software

Figure 4-9. Local Area Connection Properties

5. Select Internet Protocol Version 4 (TCP/IPv4).

6. Click the Properties button. The following window appears as shown in Figure
4-10.

4-10
 Pulse Shaping
Installing the Pulse Shaper Software

Figure 4-10. Internet Protocol Version 4 Properties

7. Click the Use the following IP address radio button to manually assign the IP
address.
8. Assign the IP address to 192.68.3.23x (x cannot be 0).
9. Assign the subnetmask setting to 255.255.240.0.
10. Click OK to accept these manual changes.

4-11
Pulse Shaping
Pulse Shaper Configuration Procedures

Pulse Shaper Configuration Procedures

You can connect to the Pulse Shaper program from either an Ethernet or RS-232
connection.

Connecting using Ethernet

You can connect to the Pulse Shaper using an Ethernet connection from your
computer to the laser. This procedure starts a connection to the laser over a network
via a specific IP Serial Port.
To connect using Ethernet:
1. Connect your PC to the laser using network cable.
2. Configure the Local Area Connection settings for Ethernet as explained in
“Configuring a Local Area Connection for Ethernet” on page 4-9.
3. Start the Pulse Shaper program.
4. Click Laser->Connect. The Laser Connection dialog box appears as shown in
Figure 4-11.
Figure 4-11. Pulse Shaper - Ethernet Laser Connection

5. Click the Ethernet radio button.

6. Select the IP address of the laser from the drop-down listbox.
7. Click OK.

4-12
 Pulse Shaping
Pulse Shaper Configuration Procedures

The status is displayed in the Session box indicating that the connection is
successful.

Connecting Using RS-232

You can connect to the Pulse Shaper program using an RS-232 Serial connection
from your computer to the laser. This procedure starts a connection to the laser over
RS-232 serial cable via a specific port on the host machine.
To configure an RS-232 serial connection:
1. Connect a RS-232 serial cable from your computer to the laser.
2. Start the Pulse Shaper program.
3. Click Laser->Connect. The Laser Connection dialog box appears as shown in
Figure 4-12.
Figure 4-12. Pulse Shaper - RS-232 Laser Connection

4. Click the RS-232 radio button.

5. Select a valid COM port on the laser from the drop-down listbox.
6. Click OK.

4-13
Pulse Shaping
Pulse Shaper Configuration Procedures

The status is displayed in the Session box indicating that the connection is
successful.

Using the Offline Option

You can export and import a configuration from a laser connection and store it for
later use with the Offline option. When you export a configuration, the chart
(including unused time segments) is preserved with the original time scale.
To use the Offline option:
1. Start the Pulse Shaper program.
2. Click Laser->Connect. The Laser Connection dialog box appears as shown in
Figure 4-13.
3. Click Offline.
Figure 4-13. Pulse Shaper - Offline Option

4. Export or import a pulse configuration as detailed in the next sections.

4-14
 Pulse Shaping
Pulse Shaper Configuration Procedures

Exporting a Configuration
To export a saved configuration from a previous laser connection (lcfg file.):
1. Click Export... The following dialog box appears as shown in Figure 4-14 on
page 4-15.
Figure 4-14. Export Configuration

2. Accept the default filename or rename the file and click Save.

Importing a Configuration
To import a saved configuration from a previous laser connection (lcfg file.):
1. Click Import... The following dialog box appears as shown in Figure 4-15 on
page 4-16.

4-15
Pulse Shaping
Pulse Shaper Configuration Procedures

Figure 4-15. Import Configuration

2. Select the configuration file (.lcfg) and click Open.

3. Click Yes to overwrite an existing configuration if applicable.

4-16
 Pulse Shaping
Using the Pulse Shaper Program

Using the Pulse Shaper Program

To start the Pulse Shaper program:
1. Go to All Programs ->IPG Laser GmbH ->PulseShaper.
2. Select PulseShaper.
Figure 4-16. Pulse Shaper Program

The Pulse Shaper interface appears as shown in Figure 4-17.

Figure 4-17. Pulse Shaper Interface

4-17
Pulse Shaping
Using the Pulse Shaper Program

Table 4-1 provides the descriptions for the four menu items in the Pulse Shaper
program.

Table 4-1. Pulse Shaper Menu Items

Menu Name Description

Laser • Connect — Connects to the laser via Ethernet or RS-232. You can also the Offline option
and import a saved Pulse Profile configuration file.
• Disconnect — Disconnects the Pulse Shaper program from the laser.
• Synchronization — Synchronizes the Pulse Shapes with the laser using the Ethernet IP
address or RS-232 connection.
• Backup — Backs up the configuration profile to a .bkp file.
• Restore — Restores the configuration profile from a backup file. All current data is replaced
with data stored in the backup file.
• Pulse mode — Indicates that Pulse mode is active.
• Exit — Closes the Pulse Shaper program.
Shape • New — Creates a new Pulse Shaping profile.
• Read from Laser — Loads and displays a Pulse Shaping profile from the laser.
• Write to Laser — Saves the current Pulse Shaping profile to the laser. This option only
saves the effective pulse.
• Delete in Laser — Deletes a Pulse Shaping profile that is stored in the laser.
• Read from File — Loads and displays a Pulse Shaping profile from a saved file (.shp) on
your computer.
• Write to File — Saves the current Pulse Shaping profile to a file (.shp) to your computer.
Sequence • New — Creates a new Pulse Sequence.
• Read from Laser — Loads and display a Pulse Sequence from the laser.
• Write to Laser — Saves a Pulse Sequence to the laser.
• Delete in Laser — Deletes a Pulse Sequence from the laser.
• Read from File — Loads and displays a Pulse Sequence from a saved file (.sec) on your
computer.
• Write to File — Saves a Pulse Sequence to a file (.sec) to your computer.
Scale • New — Creates a new Pulse Scale.
• Read from Laser — Loads and display a Pulse Scale from the laser.
• Write to Laser — Saves current Pulse Scale to the laser. This option only saves the effective
Pulse Scale.
• Delete in Laser — Deletes a Pulse Scale that stored in the laser.
• Read from File — Loads and display a Pulse Scale from a file (.scl) on your computer.
• Write to File — Saves current Pulse Scale to a file (.scl) to your computer.

4-18
 Pulse Shaping
Using the Pulse Shaper Program

Table 4-2 provides descriptions for the Pulse Shaper main window options.

Table 4-2. Main Window Descriptions

Name Description
Session Panel
Mode Displays the active session type.
Connection Displays the connection status (Ethernet or RS-232).
Laser Configuration Panel
ID The configuration identification for the laser.
SN The serial number of the laser.
CW Indicates if the CW operating mode (Continuous Wave) is active. In CW mode, the
maximum pulse duration and duty cycle are not applicable.
Max Width, ms Maximum allowed pulse width.
Min Width, ms Minimum allowed pulse width.
Max Power, W Maximum allowed pulse power.
Max Energy, J Maximum allowed pulse energy.
Sample Time, µs Minimum interval for pulse points.
Power Threshold % Emission (current) effective zero level.

4-19
Pulse Shaping
Using the Pulse Shaper Program

Laser Control Tab

The Laser Control tab lets you activate a Pulse Sequence.
Figure 4-18 shows the Laser Control tab.
Figure 4-18. Laser Control Tab

Table 4-3 provides descriptions for the options in the Laser Control tab.

Table 4-3. Laser Control Tab Descriptions

Name Description
Waveform Toggles the waveform status.
Waveform mode Toggles between a Single Pulse and Pulse Sequence.
Waveform sequence Select a Pulse Sequence from the listbox. Click SET to apply the Pulse Sequence
for viewing in the chart.
Emission Click ON to show the emission power in the chart.
Error Code Click Reset Errors to clear error codes after they are addressed.

4-20
 Pulse Shaping
Using the Pulse Shaper Program

Shape Editor Tab

The Shape Editor lets you create and edit various Pulse Shape profiles and save them in
the Pulse Shapes library on the laser or locally to your computer.
Figure 4-19 shows the Shape Editor tab.
Figure 4-19. Shape Editor Tab

Figure 4-20 shows the Points Panel in the Shape Editor tab.

4-21
Pulse Shaping
Using the Pulse Shaper Program

Figure 4-20. Shape Editor Tab - Points Panel

Figure 4-21 shows the Shift Panel in the Shape Editor tab.
Figure 4-21. Shape Editor Tab - Shift Panel

Table 4-4 provides descriptions for the Point and Shift Panel controls in the Shape
Editor tab.

4-22
 Pulse Shaping
Using the Pulse Shaper Program

Table 4-4. Shape Editor Tab - Points and Shift Panel Controls

Item Name Description

Points
Add Point Tool Plots pulse points in the chart and automatically forms lines.
Draw Curve Tool Plots an arbitrary pulse in the chart and automatically forms points
and lines along the graph (using your mouse).
Move Point Tool Relocates a pulse point on the chart.
Delete Point Deletes a pulse point from the Table box.
Clear Clears the entire pulse chart.
a
Shift Panel
1 Emission Shift Down Shifts all pulse points down in emission.
2 Emission Shift Up Shifts all pulse points up in emission.
3 Increase Emission Shift Step Increases the emission shifting step size.
4 Decrease Emission Shift Step Decreases the emission shifting step size.
5 Emission Step Sets the emission shifting step size (.25 - 100%).
6 Time Shift Left Shift all pulse points back in time.
7 Time Shift Right Shifts all pulse points forward in time.
8 Increase Time Shift Step Increases the time shifting step size.
9 Decrease Time Shift Step Decreases the time shifting step size.
10 Emission Scale Ref Sets the reference point for emission scaling (0 - 100%).
a. Due to the digitized nature of the pulses, approximations are used to compute modulations. Mod-
ulation step values (especially very small ones) might not have an effect. IPG recommends you
save the original pulse while manipulating the pulse for easy comparison between the modulated
pulse and the original.

4-23
Pulse Shaping
Using the Pulse Shaper Program

Figure 4-22 shows the Scale Panel in the Shape Editor tab.
Figure 4-22. Shape Editor Tab - Scale Panel

Table 4-5 provides descriptions for the Scale Panel controls in the Shape Editor tab.

4-24
 Pulse Shaping
Using the Pulse Shaper Program

Table 4-5. Shape Editor Tab - Scale Panel Controls

Name Description
a
Emission Scale Ref
1 Increase Emission Increases the reference point for emission scaling.
Scale Ref
2 Decrease Emission Decreases the reference point for emission scaling.
Scale Ref
3 Time Step Sets the time shifting step size (ms).
4 Compress Emission Compresses all pulse points in emission with regards to the reference point.
5 Expand Emission Expands all pulse points in emission with regards to the reference point.
6 Decrease Emission Decreases the step size for emission scaling.
Scale Step
7 Increase Emission Increases the step size for emission scaling.
Scale Step
8 Emission Scale Step Sets the step size for emission scaling (.25 - 100%).
Time Scale Ref
9 IncreaseTime Scale Increases the reference point for time scaling.
Ref
10 Decrease Time Decreases the step size for time scaling.
Scale Step
11 Time Scale Ref Sets the reference point for time scaling (0 - 50ms).
12 Compress Time Compresses all pulse points in time with regards to the reference point.
13 Expand Time Expands all pulse points in time with regards to the reference point.
14 IncreaseTime Scale Increases the step size for time scaling.
Step
15 Decrease Time Decreases the reference point for time scaling.
Scale Ref:
16 Mod Time Scale Sets the step size for time scaling (.25 - 100%).
a. Due to the digitized nature of the pulses, approximations are used to compute modulations, so
modulation step values, especially the very small ones might not have an effect. It is recom-
mended to save original pulse while manipulating the pulse so it's easy to compare the modu-
lated pulse against the original.

4-25
Pulse Shaping
Using the Pulse Shaper Program

Figure 4-23 shows the chart in the Shape Editor tab.

Figure 4-23. Shape Editor Tab - Chart

Table 4-5 provides descriptions for the options in the Chart in the Shape Editor tab.

Table 4-6. Shape Editor Tab - Chart

Name Description
Chart Panela
1 Time (X-axis) Time domain in s, ms, or sec.
2 Emission (Y-axis) Emission level in percent power.
3 Power Threshold Visual representation of the current threshold level in the laser configuration.
Appears in pink box in the chart. Any pulse data within does not have any
power.
4 Profile Memory Current pulse memory utilization/maximum allowable.

4-26
 Pulse Shaping
Using the Pulse Shaper Program

a. Due to the digitized nature of the pulses, approximations are used to compute modulations, so
modulation step values, especially the very small ones might not have an effect. It is recom-
mended to save original pulse while manipulating the pulse so it is easy to compare the modu-
lated pulse against the original.

Creating a New Pulse Shape Profile

To create a new Pulse Shape profile:
1. Select Shape -> New.
2. Select a time scale unit (s, ms, or sec) from one of the Time: buttons at the
bottom of the window.
3. Draw the shape by adding points.
4. To change points, modify values in the Table box in the left pane.
5. Once the Pulse Shape is complete, you can save it to the Pulse Shapes library
or locally on your computer.
a. To save to the Pulse Shapes library, on the laser select Shape -> Write to
Laser.
b. To save to your computer, select Shape -> Write to File.

4-27
Pulse Shaping
Using the Pulse Shaper Program

Creating a Single Pulse Shape

For simple applications, you might require only a Single Pulse shape.
To create a single Pulse Shape:
1. Select New from the Shape menu. A new shape appears in the Shape Editor tab.
2. Select the Add Point tool and use your mouse to plot points along the pulse
chart. Lines are automatically generated to connect the plotted dots.
3. Click the Show points checkbox to display the graphical points along the grid
lines in the chart.
4. Select the Move tool and drag and move any pulse point. You should be able
to move the pulse point in any direction.
5. Select Delete and click on any existing point. The point is removed and the
pulse line is regenerated to connect the neighboring points.
6. Select the Add Point tool and click between any two existing pulse points. The
pulse lines are updated to connect the new point to the neighboring ones.
7. Click Clear to remove the entire pulse chart.

4-28
 Pulse Shaping
Using the Pulse Shaper Program

Shifting a Pulse Shape

You can manipulate an existing Pulse Shape to create new variations. This method
can save you time and achieve better symmetry. See Figure 4-21 for an illustration
of Shift Panel controls.
To shift a pulse:
1. Select New from the Shape menu.
2. Create a preliminary pulse (preferably an alternating one) such as a square or
sine wave.
3. Set an emission step percentage value in the Shift Panel.
4. In the Shift Panel, click Emission Shift Down (Eu ∧) or Emission Shift Up
(∨ Ed) to introduce an emission offset to the pulse.
5. Set a certain Time Step value in the Shift Panel.
6. Click Time Shift Left (Tr>) Time Shift Right (<TI) to introduce a time offset to
the pulse.
7. Set an Emission Scale Ref percentage value. It should be the effective zero point
of your pulse to get the best result.
For example, if you are modulating a sine wave, set to be in the center point.
Also, set an Emission Scale percentage value then click Expand Emission or
Compress Emission to scale effective emission with respect to the reference
point.
8. Use the Time scaling slider to set a Time scale value. It should be the effective
zero point of your pulse to get the best result.

Note Because of the sample time constraint, scaling can be unsymmetrical, and there could
be a small range of ineffective scaling factors, all that is due to the sample
approximation during the calculations. IPG recommends you save the original pulse
prior to modulating a pulse.

4-29
Pulse Shaping
Using the Pulse Shaper Program

Pulse Shape Storage and Recall

On a Laser
This section requires connection to the laser. It is important to write pulses to the
laser to use and activate them.
1. Sketch a Pulse shape as explained in “Creating a Single Pulse Shape” on page
4-28.
2. Select Shape->Write to Laser.
Figure 4-24. Write a Pulse Profile to the Laser

3. Select a pulse ID or enter a new name for the pulse profile and click OK.
The message “Shape was saved” appears.
The pulse data is encoded and transmitted to the laser for storage.
To recall:
1. Select Shape->Read from Laser.
2. Select a pulse profile ID and click OK.

4-30
 Pulse Shaping
Using the Pulse Shaper Program

The Pulse Shape is fetched, decoded, and displayed on the chart. The displayed
pulse might appear differently as any unused time in the chart is removed as only
the effective pulse width is saved.

On a Host PC
You can write Pulse Sequences to your computer to use and activate them in the
Sequence Editor.
To save a Pulse Sequence your computer:
1. Select Shape -> Write to File.
2. Enter a name for the file and click Save.
To recall a Pulse Shape:
1. Select Shape->Read from File.
2. Select a pulse ID and click OK.
The Pulse Shape is fetched and loaded into the chart.

Deleting a Pulse Profile

You can only delete or make changes to a pulse if the pulse profile status is “Idle”.
The “In Use” status identifies that the laser is configured with that pulse.
You cannot delete a pulse profile that has an attachment status greater than zero,
which means that the pulse is used by one or more existing sequences. However, you
can overwrite a pulse if you accept to bypass the warning.
To delete a Pulse Shape profile:
1. Select Shape->Delete in Laser. The Delete a Pulse Shape dialog box appears.

4-31
Pulse Shaping
Using the Pulse Shaper Program

Figure 4-25. Delete a Pulse Profile in the Laser

2. Select a profile ID to delete.

3. Click Delete.
4. Click Yes in the confirmation box.

4-32
 Pulse Shaping
Using the Pulse Shaper Program

Single Pulse Activation

To activate a Single Pulse:
1. Select Laser -> Connect. See “Pulse Shaper Configuration Procedures” on page
4-12 for the steps for connecting via Ethernet or RS-232.
2. Click the Laser Control tab.
3. Toggle the Waveform button to Enabled.
4. Toggle the Waveform mode to Single Pulse.
5. Select a Waveform shape from the listbox.
6. Click SET.
7. Click Emission to confirm and start countdown.
The selected pulse is emitted after the countdown.
8. Click Emission again to clear the status. This also stops a pulse sequence if it
is set to infinite repeats.
Figure 4-26. Single Pulse Activation

4-33
Pulse Shaping
Using the Pulse Shaper Program

Single Pulse Activation using the Touch-Display Screen

This section requires connection to the laser.
1. After storing a pulse to the laser, ensure the Emergency Stop button is released
on the laser and then press the green button to turn on the power supply.

Note Both Analog and Modulation modes must be set to “Off” to configure the pulse mode.
You can access these modes from the Setup submenu in the Touch-Screen Display.

2. On the laser touch-screen, select Setup->Pulse Setting-> Waveform Mode.

3. Toggle Waveform Pulse Mode to Enabled.
4. Select Single Pulse.
5. Use the Up/Down arrows to select a specific pulse.

Note If no pulse profile is saved the laser's pulse profile list, then “!! No Profiles
Available!!” is displayed.

6. Pulse Information/Preview (optional) —To view information about the pulse,

click on the Pulse Browser button. This is the button with the name of the pulse.
Once the information page appears, you can use the arrows to scroll through all
available pages.
7. Click anywhere in the text space to go to the Preview page. You can see the
shape of the pulse.
8. Click Return twice to go back to the Waveform page.
9. Click Configure & Return.
It is important to configure the laser with the selected pulse (once) before usage.
10. After the configuration is complete, click Return twice to go back to the main
page.
11. Click Emission and then click OK to confirm and start countdown. The selected
pulse is emitted after the countdown.
12. Click Emission again to clear the status.

4-34
 Pulse Shaping
Using the Pulse Shaper Program

Scaling Editor
The Scaling Editor lets you scale pulses within a sequence (ramp up and down).
If Analog Power Control is enabled, it allows on-the-fly scaling of the Pulse Sequence by
varying analog input signal. You do not need to use Scaling Editor. See “Accessing the
Web User Utility” on page A-5 to enable Analog Power Control.
Figure 4-27 shows the Scaling Editor tab.
Figure 4-27. Scaling Editor

Table 4-5 provides descriptions for in Scaling Editor controls.

4-35
Pulse Shaping
Using the Pulse Shaper Program

Table 4-7. Scale Editor Controls

Name Description
Point Panel
1 Time, ms, sec, or Time scale unit in ms, sec, or min.
min
2 Scaling, W % Enter a start point value for viewing the Pulse Scale in the chart.
3 Power (%) Click the Power button to toggle between percentage and watts.
4 Show points Click the Show points checkbox to display graphical points along the grid lines
in the Scale chart. This option is disabled by default.
5 Show grid Click Show grids to display a grid of horizontal and vertical lines for aligning
pulse points in the Scale chart.This option is enabled by default.
6 Time scaling Use the Time scaling slider to adjust the zoom in and out.

Use the time shift controls and alignment cursors for more accurate editing. Use
the Time and Emission indicators in the Status panel for guidance.
Status Panel
3 Scaling width, ms, Total time between start and finish.
sec, or min
4 Start point, ms, Start value from a certain point.
sec, or min.

Creating a New Pulse Scale

.To create a Pulse Scale:
1. Select Scale -> New.
2. Select a scaling width.
3. Draw the scale by adding points.
a. To save to the Pulse Sequence library, on the laser select Scale -> Write to
Laser.
b. To save to your computer, select Scale -> Write to File.

4-36
 Pulse Shaping
Using the Pulse Shaper Program

Sequence Editor
A Pulse Sequence is an arrangement of pulses, designed for finite or infinite repeats,
and organized into steps. Each step has an assigned an existing pulse, pre-delay, and
repeat amount.
The Pulse Shaping program checks each created sequence for average power and
other laser limitation violation, and prompts you to make adjustments.
The Sequence Editor lets you create a sequence of pulses (pulse train) using Pulse Shapes
from Pulse Sequence library.
Figure 4-28 shows the Sequence Editor tab.
Figure 4-28. Sequence Editor Tab

4-37
Pulse Shaping
Using the Pulse Shaper Program

Table 4-8 provides descriptions for in Sequence Editor controls.

Table 4-8. Sequence Editor Controls

Name Description
Add Click Add to insert a sequence step prior to the one currently selected.
Delete Click Delete to remove the selected sequence step.
Up Click Up to move the selected sequence up in the order of sequence steps.
Down Click Down to move the selected sequence step down in the order of sequence steps.
Repeats The number of repeats for the current sequence.
Infinite Check the Infinite checkbox for continuous repeats of the current sequence.
Interval. ms Enter a interval value.
Scaling ID Click to open the Pulse Scaling dialog box where you can select a scaling ID.
Remove Scaling Click Remove Scaling to remove the select scaling ID from the Scaling ID box.
Name Names of the current sequence.
Pre-Delay A delay that precedes every repetition of the corresponding sequence step.
Repeats The number of times to repeat the corresponding.

Creating a New Pulse Sequence

You can make a pulse train with variable Pulse Shapes and pulse repetition rates.
To create a Pulse Sequence:
1. Select Laser -> Connect. See “Pulse Shaper Configuration Procedures” on page
4-12 for the steps for connecting via Ethernet or RS-232.
2. Select Sequence -> New.
3. Select the required Pulse Shape from Pulse Shapes library.
4. Define the delays between pulses in the Delay box.
5. Enter the number of repeats in the Repeats box.
6. Select scaling of pulses (ramp up/ramp down) from the Pulse library and add
them on top of the sequence.
If Analog Power Control is enabled, it allows on-the-fly scaling of the Pulse Sequence
by varying analog input signal. You do not need to use Scaling Editor. See “Accessing
the Web User Utility” on page A-5 to enable Analog Power Control.
a. To save to the Pulse Sequence library, on the laser select Sequence -> Write
to Laser.
b. To save to your computer, select Sequence -> Write to File.

4-38
 Pulse Shaping
Using the Pulse Shaper Program

Building a Sequence
To build a sequence:
1. Select New from the Sequence menu. A new Pulse Sequence appears in the
Sequence Editor tab.
2. Click Add to add a sequence step.
3. Enter a value (in ms) in the Delay box.
4. Select a Pulse Profile from the listbox.

5. Enter a number of repeats (number of times the selected Pulse Profile with delay
must be repeated ) in the Repeats box.
6. Click Add again to add more sequence steps.
You can set the number of sequence repeats by setting values in the Repeats
box and Interval, ms box.
7. Click the Shape ID button to display a list of Pulse Shapes as shown in Figure
4-29.

4-39
Pulse Shaping
Using the Pulse Shaper Program

Figure 4-29. Pulse Shapes Dialog Box

8. Select a shape ID for the sequence and click OK.

9. Click the Scaling ID button to display a list of Pulse Scaling IDs as shown in
Figure 4-30.

4-40
 Pulse Shaping
Using the Pulse Shaper Program

Figure 4-30. Pulse Scaling Dialog Box

10. Select a scaling ID for the sequence and click OK.

The preview of the sequence is refreshed when changes are made to the pulse.
Additionally, laser limitation violations are re-checked.

4-41
Pulse Shaping
Using the Pulse Shaper Program

Modifying a Pulse Sequence

To modify a sequence:
1. Highlight an existing step.
2. Click Up to shift up the selected sequence step in the sequence order.
3. Click Down to shift down the selected sequence step in the sequence order.
4. Click Delete to remove the selected sequence step.

Pulse Sequence Storage and Recall

This section requires connection to the laser.

On a Laser
You can write Pulse Sequences to the laser to use and activate them in the Sequence
Editor.
1. Select Sequence->Write to Laser. The Save Sequence dialog box appears.
Figure 4-31. Save Sequence

2. Select a sequence ID or enter a new name for the sequence and click OK.
The message “Sequence was saved” appears.

4-42
 Pulse Shaping
Using the Pulse Shaper Program

To recall a Pulse Sequence:

3. Select Sequence->Read from Laser.
4. Select a sequence ID and click OK.
The sequence is fetched and loaded into the chart.

On a Host PC
You can write Pulse Sequences to your computer to use and activate them in the
Sequence Editor.
To save a Pulse Sequence your computer:
1. Select Sequence -> Write to File.
2. Enter a name for the file and click Save.
To recall a Pulse Sequence:
1. Select Sequence->Read from File.
2. Select a sequence ID and click OK.
The sequence is fetched and loaded into the chart.

Deleting a Pulse Sequence

You cannot delete a Pulse Sequence if the status is not “Idle.” When the status is “In
Use” it means that the laser is configured with that Pulse Sequence.
To delete a Pulse Sequence:
1. Select Sequence->Delete in Laser.

4-43
Pulse Shaping
Using the Pulse Shaper Program

Figure 4-32. Delete a Sequence in the Laser

2. Select a sequence ID to delete.

3. Click Delete.
4. Click Yes in the confirmation box.

4-44
 Pulse Shaping
Using the Pulse Shaper Program

Pulse Sequence Activation

To activate a Pulse Sequence:
1. Click the Laser Control tab.
2. Toggle the Waveform button to Enabled.
3. Toggle the Waveform mode to Pulse Sequence.
4. Select a Waveform sequence from the listbox.
5. Click SET.
6. Click Emission to confirm and start countdown.
The selected pulse is emitted after the countdown.
7. Click Emission again to clear the status. This also stops a pulse sequence if it
is set to infinite repeats.
Figure 4-33. Pulse Sequence Activation

4-45
Pulse Shaping
Using the Pulse Shaper Program

Pulse Sequence Activation using the Touch-Screen

Display
You can use the Touch-Screen Display on the laser’s front panel for manual control.
You can view information about the laser’s state and settings.
After storing a Pulse Sequence to the laser, ensure the E-stop button is released on
the laser. Then press the green button to turn on the power supply.

Note Both Analog and Modulation modes must be set to “Off” to correctly configure the
Pulse Sequence mode. To change them, select Pulse Menu->Pulse Setting.
To activate a Pulse Sequence from the Touch-Screen Display on the laser:

1. Select Pulse Menu->Pulse Setting->Waveform Mode.

2. Toggle Waveform Pulse Mode to Enabled.
3. Select Pulse Sequence.
4. Use the Up and Down arrows to select a specific Pulse Sequence.
5. Pulse Sequence Information/Preview (Optional) - To view information about
the Pulse Sequence, click on the Pulse Browser button. The information page
appears. You can use the arrows to scroll through all available pages.
6. Click anywhere in the text space to go to the Preview page. You can see the
shape of the pulses in the sequence. Use the arrows to see the entire page.
7. Click Return twice to go back to the Waveform page.
It is important to configure the laser with the selected pulse sequence (once)
before usage.
8. Click Configure & Return. After the configuration is complete, click Return
twice to go back to the main page.
9. Click Emission, and then click OK to confirm and start countdown.
The selected pulse is emitted after the countdown. Click Emission again to clear
the status. This also stops a pulse sequence if it is set to infinite repeats.

4-46
 Pulse Shaping
Using the Pulse Shaper Program

Remote Control Interface

This interface is designed to provide remote control. It covers the pulse-shaping
feature and it not meant to be a comprehensive control utility.

Note This interface works simultaneously with the Touch-Screen display.

To start the interface:

1. Select Remote Control from the top menu.
2. Use the Setup panel to enable the Waveform (pulse) mode.
3. Select the pulse or sequence mode.
4. Select a pulse or sequence then configure the laser.

4-47
Pulse Shaping
Using the Pulse Shaper Program

4-48
 5
Troubleshooting
Error Messages on the Display and
Status Bits
The following table lists errors and possible solutions, which are associated with the
displayed errors on the touch-screen display or returned status bits via the RS-232
connection.

Table 5-1. Error Messages with Possible Solutions

Issue Comments

Optical Interlock (Bit 30)

Result: The internal main power supply is automatically switched off.

Cause: Either the delivery fiber cable is mechanically damaged or the output
connector is not plugged into an appropriate optical head.

Possible Solution: Send reset error command (“RERR”). If the message does
not disappear, contact a representative from IPG Photonics for assistance.

Low Temperature (Bit 24)

Result: The power supply and laser emission is switched off.

Cause: The case temperature of the laser is too low. Check if outside conditions
are within the specified range.

Possible Solution: This message and error bit disappear as soon as case
temperature of the laser module drops in the operating range.

5-1
Troubleshooting
Error Messages on the Display and Status Bits

Issue Comments

Overheat (Bit 1)

Result: The power supply and laser emission is switched off.

Cause: This means that case temperature of the laser is too high.

Possible Solution: Check if outside conditions are within the specified range and
if the conditions for sufficient airflow are provided. This message and error bit
disappear as soon as case temperature of the laser modules drops in the
operating range.

Module Disconnected (Bit 6)

Result: The power supply and laser emission is switched off.

Cause: This means that digital data communication with the laser module inside
the device is broken.

Possible Solution: Try to reset the error. If it appears again, contact IPG Photonics
for assistance.

Power Supply Failure (Bit 19)

Result: The power supply and laser emission is switched off.

Cause: This means that even though the internal main power supply is switched
on there is no voltage applied to the laser module.

Possible Solution: Try to reset the error. If it appears again, contact IPG Photonics
for assistance.

5-2
 Troubleshooting
Error Messages on the Display and Status Bits

Issue Comments

Power Supply Failure 2 (Bit 25)

Result: The internal main power supply is automatically deactivated.

Cause: This means that though the internal main power supply is switched on
and the voltage is applied to the laser module, the value of this voltage is not
within the preinstalled range.

Possible Solution: Reset the error and switch on the internal main power supply.
If the error reappears, contact IPG Photonics for assistance.

High Back Reflection (Bit 3)

Result: Laser emission is switched off.

Cause: The back reflected power exceeded the pre-installed maximal applicable
level.

Possible Solution: Check if the focus position is correctly adjusted and that there
are no surfaces, which can lead to the high level of back reflection. Reset the
error using RS-232 (“RERR” command) or touch-screen display on the front
panel.

Critical Error (Bit 29)

Result: The power supply and laser emission is switched off.

Cause: The system has detected an error that is considered critical.

Possible Solution: Neither reset command (“RERR”) nor restart of the device
clears this error. Contact IPG Photonics for assistance. Be ready to read the
Module Error Code (RMEC command) from the laser and submit it to an IPG
Technical Support Specialist.

5-3
Troubleshooting
Error Messages on the Display and Status Bits

Issue Comments

Duty Cycle Too High

Result: The duty cycle is too high.

Cause: The duty cycle is the percentage of how long the laser is in the “on” state
in the given modulated period.

Possible Solution: Check the modulation signal. Try to reset the error. If it appears
again, contact IPG Photonics for assistance.

High Pulse Energy

Result: The pulse energy of the laser is too high.

Cause: A pulsed laser periodically emits pulses of energy in an ultra-short time

duration.

Possible Solution: Check the modulation signal. Try to reset the error. If it appears
again, contact IPG Photonics for assistance.

5-4
 Troubleshooting
Error Messages on the Display and Status Bits

Issue Comments

Average Power Too High

Result: The laser power is too high.

Cause: The system has detected an error that is considered critical.

Possible Solution: Check the modulation signal. Try to reset the error. If it appears
again, contact IPG Photonics for assistance.

Pulse Too Long

Result: The laser pulse is too long.

Cause: The system has detected an error that is considered critical.

Possible Solution: Check the modulation signal. Try to reset the error. If it appears
again, contact IPG Photonics for assistance.

Internal Communication Error

Result: There is no CAN connection.

Cause: Occurs when there is no connection to the Controller Area Network

(CAN).

Possible Solution: Try to reset the error. If it appears again, contact IPG Photonics
for assistance.

5-5
Troubleshooting
Error Messages on the Display and Status Bits

Issue Comments

Pulse Too Short

Result: Pulse Too Short warning appears in touch-screen display.

Cause: The system has detected an error that is considered critical.

Possible Solution: Click Warning in the touch-screen display. The warning

message appears. Try to reset the error. If it appears again, contact IPG
Photonics for assistance.

5-6
 A
Web User Utility
Overview
You can troubleshoot your laser using the IG337 Web User Utility, which provides
status information and digital control functionality.

This appendix explains how to configure your computer's communication protocols

to connect to the laser via a PC.

Configuration Procedures
You can connect to the Web User Utility from either an Ethernet or RS-232
connection.

Configuring an Ethernet Connection

The following procedure assumes you are familiar with operating the YLM-QCW
laser. IPG recommends that you review all safety and operational procedures before
proceeding.
1. Connect PC to the laser using a standard Ethernet cable.
2. Manually configure the Local Area Connection settings for Ethernet (see
“Configuring a LAN Connection for Ethernet” on page A-2).
3. Open your web browser and enter the IP address of the Internet Protocol. If the
connection is successful, the IG337 Web User Utility page appears (as shown
in Figure A-6).

Configuring an RS-232 Serial Connection

See “Connecting Using RS-232” on page 4-13 for step-by-step instructions.

A-1
Web User Utility
Configuring a LAN Connection for Ethernet

Configuring a LAN Connection for

Ethernet
To configure a LAN connection for Ethernet:
1. Go to Control Panel -> Network and Internet -> Network and Sharing
Center.
2. Click Change adapter settings.
3. Select a Local Area Connection icon. The following window appears as shown
in Figure A-1.
Figure A-1. Local Area Connection Status

4. Click Properties. The following window appears as shown in Figure A-2.

A-2
 Web User Utility
Configuring a LAN Connection for Ethernet

Figure A-2. Local Area Connection Properties

5. Select Internet Protocol Version 4 (TCP/IPv4).

6. Click Properties. The following window appears as shown in Figure A-3.

A-3
Web User Utility
Configuring a LAN Connection for Ethernet

Figure A-3. Internet Protocol Version 4 Properties

7. Click the Use the following IP address radio button to manually assign the
IP address.
8. Assign the IP address to 192.168.3.23x (x cannot be 0 as it is the default IP
address of the Laser).
9. Assign the Subnetmask to 255.255.240.0.
10. Click OK to accept your changes.

A-4
 Web User Utility
Configuring a LAN Connection for Ethernet

Website Data Settings

To ensure the most current Web User Utility interface is downloaded to your web
browser, you need to modify the Website data settings in Internet Explorer.

To modify the Website data settings:

1. Open Internet Explorer.
2. Select Tools -> Internet Options.
Figure A-4. Internet Explorer Options

3. Click Settings.

A-5
Web User Utility
Configuring a LAN Connection for Ethernet

Figure A-5. Website Data Settings

4. Click Everytime I visit the webpage.

5. Click OK to save this setting.

A-6
 Web User Utility
Configuring a LAN Connection for Ethernet

Accessing the Web User Utility

To access Web Utility:
1. Enter the IP address of the laser in a web browser. The Web User utility appears.
Figure A-6. IG337 Web User Utility

The items (0 to 31) in the Status group are listed in Table 3-5 on page 3-8 (Bit
Meanings).
See Table 2-6 on page 2-19 for details on main control functions.
See Figure 2-13 on page 2-17 guidelines on setting the Pulse Generator.

A-7
Web User Utility
Configuring a LAN Connection for Ethernet

2. Click the Communication Configuration link at the top of the screen to

change the IP address or baud rate. The following page appears.

3. Click the Revision link to upload the latest laser module software version. The
following page appears:

4. Click the Ellipsis button (...) to reset critical errors. The following page
appears:

5. Provide the Serial Number, Counter, and Error Code to receive a reset code
from IPG Customer Service.
6. Turn on the Aiming Beam and verify that it is visible at the optical output.

A-8
 Web User Utility
Configuring a LAN Connection for Ethernet

A-9
Web User Utility
Configuring a LAN Connection for Ethernet

A-10
 B

Service
Service and Repairs
There are no operator serviceable parts inside. Only the fuses and filter media are
replaceable. Refer all internal servicing to qualified IPG personnel.
Many issues and questions regarding the safety, set-up, operation and maintenance
of the IPG products can be resolved by reading this guide carefully. However, if you
have questions regarding the safety, set-up, operation or maintenance of your IPG
product, call the Customer Service department.
If you cannot resolve the issues by using this guide or over the telephone with a
technical support representative, you might need to return the product to IPG. See
“Product Returns” on page E-1 for more details.

Serviceable Items

The unit should never be operated with any of the covers removed, including the
front panel fan covers.
The input voltage to the laser is potentially lethal. All electrical cables and
connections should be treated as if it were a harmful level. All parts of the electrical
cable, connector or device housing should be considered dangerous.

This device is classified as a high power Class 4 laser instrument under 21 CFR
1040.10. This product emits invisible laser radiation at or around a wavelength of
1070 nm, and the total light power radiated from the optical output is greater than 20
to 1500 W (depending on model) per optical output port.
This level of light can cause damage to the eye and skin. Despite the radiation being
invisible, the beam may cause irreversible damage to the cornea. Laser safety eyewear
is not provided with this instrument, but must be worn at all times while the laser is
operational.

Service personnel should always follow correct Lockout/Tagout procedures per your
company's policy to ensure all potential energy is removed from the system before
servicing.

B-1
Service
Replacing Fuses

Replacing Fuses
Fuse Ratings: Refer to Table 18: Replacement Parts
To replace the main power fuses:
1. Disconnect the power source and remove the keys from laser.
2. Turn the laser so the rear panel is easily accessible.
3. Locate the fuses and unscrew the covers.

Important Replace blown or damaged fuses with only the same amperage fuses. Replace the
fuse(s) and covers and tighten securely.

Replacing the Filter Media

Inspect the filter media weekly and clean or replace as needed. Only use IPG parts
when replace filter media.
To access the filters, use the following procedure:
1. Unplug the line cord and remove keys from laser.
2. Remove the front bezel on the front panel of the laser (refer to Figure 5: Front
Panel ). Upon removal, the filter element will be exposed.
3. Remove the used filter and clean or replace with a new filter (Refer to Table
B-1).
4. Snap the cover back on and dispose of the dirty filter element.

Table B-1. Replacement Parts

Description Laser Categorya Part Number

Filter Media 3U P45-004679

Filter Media 4U P45-004676

Filter Media 6U P45-004679 and
P45-004704

Fuse T 10A 250VAC 3U AC P40-001743

Fuse T 15A 250VAC 3U WC, 4U AC (CW and QCW), 6U AC P40-001564

a. Refer to Laser Model Designation Codes

B-2
 C

Optical Fiber Connector Inspection and

Cleaning
Overview
You should regularly check the fiber connector for dust, dirt, or damage before you
connect to any external optic. The use of a dirty, or improperly cleaned, fiber
connector can lead to serious damage to the laser (Figure C-6 on page C-7 illustrates
possible fiber failures).

IPG Photonics is not responsible for any damages due to contaminated connectors.
Tampering with the fiber connectors without training by IPG voids the warranty.

For cleaning a fiber connector, you need the following materials:

• Powder free rubber gloves or finger cots
• Lint free optical cleaning wipes and/or swabs
• Acetone (optical grade, water free)
• Compressed air (oil free, water free)
• Microscope (IPG model or equivalent)
• Light Source
Figure C-1. Materials for Cleaning a Fiber Connector

C-1
Optical Fiber Connector Inspection and Cleaning
Overview

Important You need to wear powder free rubber gloves during this cleaning procedure. Damage
to the fiber connector can occur due to mishandling. The use of incorrect cleaning
procedures or chemicals for cleaning is not covered by the warranty.

Acetone should be handled and stored in accordance to any local regulations (e.g.
OSHA Regulation 29 CFR 1910.1200). Refer to each solvent's MSDS (Material
Safety Data Sheet) for additional information.

To clean the fiber connector:

1. Switch off the laser main power by pressing the Emergency Stop button on the
front of the unit and turning the Keyswitch to the center position.
2. Leave protective cap on and clean the fiber connector exterior with optical
cleaner, wipe it with a clean optical wipe and dry with compressed air.
3. Place fiber connector in the holder of the microscope.
4. Place pressure on the center of the securing arm before tightening the locking
screw as shown in Figure C-2.
Figure C-2. Fiber Connector Mounted on IPG Microscope

5. Remove cap and sleeve from connector as shown in Figure C-3.

Important Place the cap face down on a clean surface. Placing the cap face down on a lint free
wipe is the best choice if the surfaces are questionable.

C-2
 Optical Fiber Connector Inspection and Cleaning
Overview

Figure C-3. Fiber Cap and Sleeve Removed

6. Focus the microscope onto the connector surface.

7. Use light source to illuminate the face of the connector so that the light is
reflected from the surface of the microscope. This is achieved if you see a bright
golden shine from the IPG (yellow cable) connector end-face or a blue surface
for the connector (see Figure C-6 on page C-7).

Important Always look at the surface at a slight angle to improve visibility.

8. Inspect the surface carefully. Any contamination might lead to dark spots on
the surface and eventual fiber failure (see Figure C-6 on page C-7 for examples).
If contamination is visible on the quartz block, continue to the next step. Proceed
to Step 14 if there is no contamination visible.
9. Try to blow away the dust with compressed air from the side.

Important Never blow air directly at the surface because you could embed contaminants into
the surface. Always blow across the surface.

10. While wearing powder free gloves, fold the lint free optical wipe into halves
until it is roughly 1 X 1 ½" rectangle (see Figure C-4 on page C-5). Put a few
drops of optical cleaner onto the lint free optical cleaning wipe on the folded
edge of the wipe as indicated.

C-3
Optical Fiber Connector Inspection and Cleaning
Overview

Important Do not ever reuse a lint free optical wipe or swab to clean the end face.

11. Re-inspect the lens.

12. Repeat step 10 with Acetone if lens is still contaminated.
13. If necessary, put a drop of Acetone onto a cleaning swab and gently wipe away
contamination in a circular motion being careful not to scratch the lens. Then
repeat from step 10.

Do not touch the tip of the cleaning swab with your fingers and use each swab only
once to prevent contamination.

14. Repeat above cleaning steps until all contamination is removed. This cleaning
procedure can be stopped at any time if a good result has already been achieved.
After fiber connector is clean use compressed air to clean the protective sleeve
and install onto the connector.

Damage to the fiber connector can occur due to mishandling, the use of incorrect
cleaning procedures, or chemicals for cleaning. This is not covered by the warranty.
15. If the fiber is not to be connected immediately with a suitable optical
component, use compressed air to clean the protection cap and install over the
fiber end.

Important Make sure you clean the cap and sleeve before installing them back onto connector.

C-4
 Optical Fiber Connector Inspection and Cleaning
Overview

Figure C-4. Fiber End-Face Cleaning

Start to clean with even pressure. Drag in only one direction.

C-5
Optical Fiber Connector Inspection and Cleaning
Overview

Figure C-5. Installing the Fiber

1. Remove the plastic protection cap at the bayonet enclosure.

2. For connecting the fiber to the bayonet, the red dot at the fiber has to be in line
with the red dot at the bayonet enclosure.
3. Gently slide the fiber all the way into the fiber port.
4. Lock the fiber into place by rotating the bayonet knurled ring.

Important Hand tighten only as the use of tools can lead to damage to the bayonet enclosure.

C-6
 Optical Fiber Connector Inspection and Cleaning
Overview

Figure C-6. Fiber Quartz Block Inspection

C-7
Optical Fiber Connector Inspection and Cleaning
Overview

C-8
 D

Warranty
Limited Express Product Warranties
IPG warrants to the original Buyer or, if Buyer is an authorized IPG reseller or
distributor, to Buyer's original customer of the IPG Product, that the IPG Product
conforms to applicable IPG Product specifications and is free from defects in
materials and workmanship. These non-transferable warranties start on the shipment
date from IPG (or other date specifically referencing the warranty start date in IPG's
sales order/order acknowledgement), and continue until the end of the warranty
period listed in IPG's sales order/order acknowledgement. If there is no warranty
period listed, then warranty period is one year. Products or major components
manufactured by parties other than IPG bear the original manufacturer's warranty
and warranty period. The obligations of IPG are limited to the repair or replacement
(at IPG's option) of any Product that does not meet the IPG warranty during the
warranty period. IPG warrants repaired or replaced Products under warranty only
for the remaining un-expired period of time in the original warranty. IPG reserves
the right to issue a credit note for any defective Products that have proved defective
through normal usage; Buyer debit memos are not allowed. This warranty governs
over any conflicting terms in Buyer's purchase order or other IPG documents except
as expressly provided herein.

Warranty Limitations
This warranty excludes and does not cover defects or damage resulting from any of
the following: contamination of external optical surfaces; unauthorized
modification, misuse or mishandling, disassembly or opening, neglect, or damage
from accident; operation outside environmental specifications or product ratings;
user software or interfacing; components and accessories manufactured by
companies other than IPG, which have separate warranties; improper or inadequate
installation, site preparation or maintenance; or failure to follow information and
precautions contained in the operating manual. Additional warranty exceptions,
limitations and exclusions may apply for laser systems manufactured by IPG and its
affiliates as set forth in the applicable quotation and sales order/order
acknowledgement. All products or components (including software) identified as
experimental, prototypes or to be used in field trials are not warranted and are
provided to the Buyer on an "as is" basis. IPG assumes no responsibility for Buyer
or third-party supplied material, components, systems or equipment. Products and
repaired Products may contain components that have been previously used in other

D-1
Warranty
Limitation of Remedies and Liabilities

products, however such Products meet IPG Product specifications for newly
manufactured Products. The Buyer must give prompt notification to IPG of any claim
under the warranty in writing. IPG has no responsibility for warranty claims more
than 30 days after the Buyer discovers or becomes aware of the claimed defect. Buyer
is responsible for providing appropriate utilities and operating environment as stated
in the operating manual and the specifications. This warranty applies only to the
original Buyer at the initial installation or delivery point. Buyer must make all claims
under this warranty and no claim will be accepted from any third party.

EXCEPT FOR THE LIMITED WARRANTIES EXPRESSLY SET FORTH

ABOVE, IPG SPECIFICALLY DISCLAIMS ANY AND ALL OTHER
WARRANTIES AND REPRESENTATIONS TO BUYER, INCLUDING
WITHOUT LIMITATION, ANY AND ALL IMPLIED WARRANTIES, SUCH AS
FREEDOM FROM INFRINGEMENT, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.

Limitation of Remedies and Liabilities

THE REMEDIES PROVIDED HEREIN ARE BUYER'S SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL IPG BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR PUNITIVE
DAMAGES (EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES)
ARISING FROM OR RELATING TO THIS ORDER OR THE PRODUCTS
(INCLUDING, LOSS OF PROFITS) WHETHER BASED ON CONTRACT, TORT
OR ANY OTHER LEGAL THEORY. IPG'S MAXIMUM LIABILITY ARISING
UNDER THESE TERMS AND CONDITIONS WILL NOT EXCEED, IN THE
AGGREGATE, THE TOTAL AMOUNT PAID FOR THE PRODUCTS BY
BUYER. THESE LIMITATIONS MAY NOT APPLY TO YOU UNDER THE
LAWS OF CERTAIN JURISDICTIONS.

Software
Firmware License Agreement
CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE
OPENING THIS PACKAGE OR SIGNIFYING YOUR ACCEPTANCE BY
CLICKING THE APPROPRIATE DIALOG BOX. OPERATING THE PRODUCT,
CLICKING THE APPROPRIATE DIALOG BOX OR USING ANY PART OF THE
SOFTWARE SIGNIFIES YOUR ACCEPTANCE OF THESE TERMS AND
CONDITIONS. IF YOU DO NOT AGREE WITH THEM, PROMPTLY RETURN
THE PRODUCT UNUSED ALONG WITH ANY OTHER RELATED ITEMS
THAT WERE INCLUDED IN THE SAME ORDER FOR FULL CREDIT.

D-2
 Warranty
Software

You, as the Customer, agree as follows:

1. DEFINITIONS

"IPG" shall mean the IPG Photonics Corporation affiliate providing Licensed
Software to Customer pursuant to this Agreement.

"IPG Software" shall mean those portions of the Licensed Software owned by IPG
or IPG affiliates.

"Licensed Software" shall mean the software, in object code form only, supplied by
IPG pursuant to this Agreement.

"Licensed Product" shall mean the Licensed Software and/or its

accompanying documentation.

"Third Party Software" shall mean those portions of the Licensed Software owned
or licensed by a third party, including but not limited to operating system code, that
is embedded within the Licensed Software.
2. LICENSE

2.1 Except as provided in section 2.2 below, you are granted a non-transferable,
nonexclusive license to use the Licensed Software only as embedded in or to be used
on a single IPG product. You may copy the Licensed Product, for backup purposes
only, in support of your use of the Licensed Software, limited to one copy. No other
copies shall be made unless authorized in writing by IPG. You must reproduce and
include all applicable copyright notices on any copy. You may not reverse compile
or otherwise reverse engineer, or modify the Licensed Software. The Licensed
Software, comprising proprietary trade secret information of IPG and/or its licensors,
shall be held in confidence by Customer and Customer shall not disclose it to third
parties, unless disclosure is required by law or legal process. In response to such
legal requirements, the Customer shall promptly notify IPG in advance of such
disclosure and reasonably cooperate in attempts to maintain the confidentiality of the
Licensed Software. No title to the intellectual property is transferred. Licensed
Software shall not be copied, reproduced, or used for any other purpose outside of
operation of the IPG product, and shall not be used on any other piece of hardware
other than the IPG product with which it was provided.

2.2 If you transfer the IPG product on which the Licensed Software is used, you
may transfer the Licensed Software to the end user of the product provided that the
end user agrees to be bound by terms no less restrictive than the provisions of this
Agreement, and provided that all proprietary markings are maintained. Any other
transfer is void and automatically terminates this license. You shall use your best
efforts to enforce such agreement and shall promptly report any violation or

D-3
Warranty
Software

suspected violation to IPG. In the event you do not enforce such agreement after a
breach, you shall, to the extent permissible by applicable law, grant IPG the right to
enforce such agreement.

2.3 The Licensed Software may include Third Party Software licensed to IPG in
addition to the licenses below. The owner of this Third Party Software (the "Third
Party") and its licensors are intended third party beneficiaries of this Agreement, and
the provisions of this Agreement relating to the Licensed Software, as the same
incorporates Third Party Software, are made expressly for the benefit of, and are
enforceable by, the Third Party and its licensors. The Third Party and its licensors
retain ownership of all copies of the Third Party Software. The Licensed Software is
warranted by IPG in accordance the above Warranty and the Third Party does not
provide an additional warranty. All Third Party Software included in the Licensed
Software is provided "AS IS" without warranty from the Third Party, and each
Third Party disclaims all warranties, either express or implied, including but not
limited to the implied warranties of merchantability, title, non-infringement or fitness
for a particular purpose with regard to the Third Party Software. The Third Party
shall not have any liability for special, indirect, punitive, incidental or consequential
damages.

2.4 In addition to the IPG Software licensed above, IPG may provide certain files
embedded in or to be used on the IPG hardware product which may be subject to the
terms of the GNU General Public License (GPL) or the GNU Lesser General Public
License (LGPL), the current text of which may be found at: http://www.gnu.org, or
another open source license. The IPG Software is proprietary software not subject
to the GPL or LGPL or other open source license, and Customer has no license to
take any action, and shall take no action, which would have the effect of subjecting
the IPG Software or any portion of the IPG Software to the terms of the GPL or LGPL
or other open source license. Customer may consult the user documentation for
identifications and further information.

2.5 For the rights granted in this Agreement, Customer shall pay to IPG the price
for the IPG hardware product in which the Licensed Software is embedded.

2.6 You understand that IPG may, at any time and in its sole discretion, update or
modify the Licensed Product or discontinue updating and/or supporting the Licensed
Product. In the case of an update or modification, you agree to allow IPG to
automatically install the Licensed Software on the IPG hardware product on which
the Licensed Software is used. Any updated or modified Licensed Product made
available and/or installed by IPG on the IPG hardware product shall become part of
the Licensed Software and subject to this Agreement.

D-4
 Warranty
Software

3. TERM AND TERMINATION

3.1 You may terminate the license granted hereunder at any time by destroying the
Licensed Product together with all copies thereof and notifying IPG in writing that
all use of the Licensed Product has ceased and that same has been destroyed.

3.2 IPG may terminate this Agreement or any license hereunder upon notice to
Customer if Customer breaches any of the terms and conditions of this Agreement
or if Customer attempts to assign this Agreement or any license hereunder without
IPG's prior written consent. Within twenty (20) days after any termination of this
Agreement, Customer shall certify in writing to IPG that all use of the Licensed
Product has ceased, and that the same has been destroyed.

3.3 All provisions of this Agreement related to disclaimers of warranty, limitation

of liability, IPG's intellectual property rights, or export shall survive any
expiration or termination and remain in effect. Termination of this Agreement or
any license hereunder shall not relieve Customer of its obligation to pay any and all
outstanding charges hereunder nor entitle Customer to any refund of such charges
previously paid.

If your product includes LaserNet™ Software, the following applies:

D-5
Warranty
Software License Agreement for LaserNet™

Software License Agreement for

LaserNet™
IPG Laser GmbH®
Single Use License
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("LICENSE")
CAREFULLY BEFORE USING THE SOFTWARE OR THE EQUIPMENT. BY
CLICKING ON THE "ACCEPT" BUTTON, USING THIS SOFTWARE, OR
USING THE EQUIPMENT THAT CONTAINS THIS SOFTWARE, YOU ARE
CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT
AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, CLICK THE "DO
NOT ACCEPT" BUTTON AND THE INSTALLATION PROCESS WILL NOT
CONTINUE, RETURN THE PRODUCT TO THE MANUFACTURER.

1. General. The software, documentation and any fonts accompanying this License
whether on disk, in read only memory, on any other media or in any other form
(collectively the "IPG Software") are licensed, not sold, to you by IPG Laser GmbH
and its affiliates ("IPG") for use only under the terms of this License, and IPG reserves
all rights not expressly granted to you. The rights granted herein are limited to IPG's
and its licensors' intellectual property rights in the IPG Software and do not include
any other patents or intellectual property rights. You own the media on which the
IPG Software is recorded but IPG and/or IPG's licensor(s) retain ownership of the
IPG Software itself. The terms of this License will govern any software upgrades
provided by IPG that replace and/or supplement the original IPG Software product,
unless such upgrade is accompanied by a separate license in which case the terms of
that license will govern.

2. Permitted License Uses and Restrictions.

A. This License allows you to install and use one copy of the IPG Software on a
single computer at a time. This License does not allow the IPG Software to exist on
more than one computer at a time, and you may not make the IPG Software available
over a network where it could be used by multiple computers at the same time. You
may make one copy of the IPG Software in machine-readable form for backup
purposes only; provided that the backup copy must include all copyright or other
proprietary notices contained on the original.

B. Except as and only to the extent permitted in this License and by applicable law,
you may not copy, decompile, reverse engineer, disassemble, modify, or create
derivative works of the IPG Software or any part thereof. THE IPG SOFTWARE IS
NOT INTENDED FOR USE IN THE OPERATION OF NUCLEAR FACILITIES,

D-6
 Warranty
Software License Agreement for LaserNet™

AIRCRAFT NAVIGATION OR COMMUNICATION SYSTEMS, AIR TRAFFIC

CONTROL SYSTEMS, OR OTHER EQUIPMENT IN WHICH THE
MALFUNTION OF THE IPG SOFTWARE WOULD RESULT IN THE
FORESEEABLE RISK OF INJURY OR DEATH TO THE OPERATOR OF THE
EQUIPMENT OR SYSTEM OR TO OTHERS.

3. Transfer. You may not rent, lease, lend, redistribute or sublicense the IPG
Software. You may, however, make a one-time permanent transfer of all of your
license rights to the IPG Software (in its original form as provided by IPG) to another
party, provided that: (a) the transfer must include all of the IPG Software, including
all its component parts, original media, printed materials and this License; (b) you
do not retain any copies of the IPG Software, full or partial, including copies stored
on a computer or other storage device; and (c) the party receiving the IPG Software
reads and agrees to accept the terms and conditions of this License.

4. Termination. This License is effective until terminated. Your rights under this
License will terminate automatically without notice from IPG if you fail to comply
with any term(s) of this License. Upon the termination of this License, you shall cease
all use of the IPG Software and destroy all copies, full or partial, of the IPG Software.

5. Limited Warranty on Media. IPG warrants the media on which the IPG Software
is recorded and delivered by IPG to be free from defects in materials and
workmanship under normal use for a period of ninety (90) days from the date of
original purchase. Your exclusive remedy under this Section shall be, at IPG's option,
replacement of the IPG Software which is returned to IPG or an IPG authorized
representative. THIS LIMITED WARRANTY AND ANY IMPLIED
WARRANTIES ON THE MEDIA INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY, OF SATISFACTORY
QUALITY, AND OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO NINETY (90) DAYS FROM THE DATE OF ORIGINAL
PURCHASE.

6. Disclaimer of Warranties. YOU EXPRESSLY ACKNOWLEDGE AND

AGREE THAT USE OF THE IPG SOFTWARE IS AT YOUR SOLE RISK AND
THAT THE ENTIRE RISK AS TO SATISFACTORY QUALITY,
PERFORMANCE, ACCURACY AND EFFORT IS WITH YOU. EXCEPT FOR
THE LIMITED WARRANTY ON MEDIA SET FORTH ABOVE AND TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE IPG
SOFTWARE IS PROVIDED "AS IS", WITH ALL FAULTS AND WITHOUT
WARRANTY OF ANY KIND TO THE FULLEST EXTENT PERMITTED BY
APPLICABLE LAW, IPG AND ITS SUPPLIERS FURTHER DISCLAIM ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, IMPLIED WARRANTIES OF TITLE, NON- INFRINGEMENT,
ACCURACY, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR
PURPOSE, AND ANY WARRANTIES THAT MAY ARISE FROM COURSE OF

D-7
Warranty
Software License Agreement for LaserNet™

DEALING, COURSE OF PERFORMANCE, OR TRADE PRACTICE. THE

ENTIRE RISK ARISING OUT OF THE USE OR PERFORMANCE OF THE IPG
SOFTWARE OR RELATED MATERIALS REMAINS WITH YOU.
APPLICABLE LAW MAY NOT ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES, SO THE ABOVE EXCLUSIONS MAY NOT APPLY TO YOU.
IPG MAY MAKE CHANGES TO THE IPG SOFTWARE AND HAS NO
OBLIGATION TO DISTRIBUTE NEWER VERSIONS.

7. Limitation of Liability. NEITHER IPG NOR ANY OF ITS SUPPLIERS

SHALL BE RESPONSIBLE OR LIABLE FOR ANY INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, EXEMPLARY, PUNITIVE OR OTHER
DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS
OF BUSINESS, LOSS OF DATA OR LOST PROFITS), UNDER ANY
CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER THEORY
ARISING OUT OF OR RELATING IN ANY WAY TO THE IPG SOFTWARE
EVEN IF IPG OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. YOUR SOLE REMEDY FOR
DISSATISFACTION WITH THE IPG SOFTWARE IS TO STOP USING THE IPG
SOFTWARE. THE SOLE AND EXCLUSIVE MAXIMUM LIABILITY TO IPG
FOR ALL DAMAGES, LOSSES AND CAUSES OF ACTION, WHETHER IN
CONTRACT, TORT (INCLUDING, WITHOUT LIMITATION, NEGLIGENCE)
OR OTHERWISE, SHALL BE THE TOTAL AMOUNT PAID BY YOU, IF ANY,
FOR USE OF THE IPG SOFTWARE. THESE LIMITATIONS MAY NOT APPLY
TO YOU UNDER THE LAWS OF CERTAIN JURISDICTIONS.

The foregoing limitations will apply even if the above stated remedy fails of its
essential purpose.

8. Export Law Assurances. You acknowledge that IPG Software is subject to U.S.
and European Union export jurisdiction. You agree to comply with all applicable
international and national laws that apply to the IPG Software, including the U.S.
Export Administration Regulations, as well as end-user, end-use and destination
restrictions issued by U.S. and other governments.

9. Government End Users. The IPG Software and related documentation are
"Commercial Items", as that term is defined at 48 C.F.R. §2.101, consisting of
"Commercial Computer Software" and "Commercial Computer Software
Documentation", as such terms are used in 48 C.F.R. §12.212 or 48 C.F.R. §227.7202,
as applicable. Consistent with 48 C.F.R. §12.212 or 48 C.F.R. §227.7202-1 through
227.7202-4, as applicable, the Commercial Computer Software and Commercial
Computer Software Documentation are being licensed to U.S. Government end users
(a) only as Commercial Items and (b) with only those rights as are granted to all other
end users pursuant to the terms and conditions herein. Unpublished-rights reserved
under the copyright laws of the United States.

D-8
 Warranty
Software License Agreement for LaserNet™

10. Controlling Law and Severability. This License will be governed by and
construed in accordance with the laws of the State of Massachusetts, as applied to
agreements entered into and to be performed entirely within Massachusetts between
Massachusetts residents. This License shall not be governed by the United Nations
Convention on Contracts for the International Sale of Goods, the application of which
is expressly excluded. If for any reason a court of competent jurisdiction finds any
provision, or portion thereof, to be unenforceable, the remainder of this License shall
continue in full force and effect.

11. Complete Agreement; Governing Language. This License constitutes the entire
agreement between the parties with respect to the use of the IPG Software licensed
hereunder and supersedes all prior or contemporaneous understandings regarding
such subject matter. No amendment to or modification of this License will be binding
unless in writing and signed by IPG. Any translation of this License is done for local
requirements and in the event of a dispute between the English and any non-English
versions, the English version of this License shall govern.

If your product includes Microsoft Corporation embedded software, then the

following applies:

D-9
Warranty
MICROSOFT CORPORATION EMBEDDED SOFTWARE END USER LICENSE AGREEMENT

MICROSOFT CORPORATION
EMBEDDED SOFTWARE
END USER LICENSE AGREEMENT
You have acquired a device ("EQUIPMENT") that includes software licensed by IPG
Photonics Corporation or its affiliates (collectively, "IPG") from an affiliate of
Microsoft Corporation ("MS"). Those installed software products of MS origin, as
well as associated media, printed materials, and "online" or electronic documentation
("SOFTWARE") are protected by international intellectual property laws and
treaties. IPG, MS and its suppliers (including Microsoft Corporation) own the title,
copyright, and other intellectual property rights in the SOFTWARE. The
SOFTWARE is licensed, not sold. All rights reserved.

IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT

("EULA"), DO NOT USE THE EQUIPMENT OR COPY THE SOFTWARE.
INSTEAD, PROMPTLY CONTACT IPG FOR INSTRUCTIONS ON RETURN OF
THE UNUSED EQUIPMENT(S) FOR A REFUND. ANY USE OF THE
SOFTWARE, INCLUDING BUT NOT LIMITED TO USE OF THE
EQUIPMENT, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA
(OR RATIFICATION OF ANY PREVIOUS CONSENT).

This EULA is valid and grants the end-user rights ONLY if the SOFTWARE is
genuine and a genuine Certificate of Authenticity for the SOFTWARE is included.
For more information on identifying whether your software is genuine, please see
http://www.microsoft.com/piracy/howtotell.

GRANT OF SOFTWARE LICENSE. This EULA grants you the following license:

1. You may use the SOFTWARE only on the EQUIPMENT.

2. Restricted Functionality. You are licensed to use the SOFTWARE to provide

only the limited functionality (specific tasks or processes) for which the
EQUIPMENT has been designed and marketed by IPG. This license specifically
prohibits any other use of the software programs or functions, or inclusion of
additional software programs or functions that do not directly support the limited
functionality on the EQUIPMENT. Notwithstanding the foregoing, you may install
or enable on a EQUIPMENT, systems utilities, resource management or similar
software solely for the purpose of administration, performance enhancement and/or
preventive maintenance of the EQUIPMENT.

3. If you use the EQUIPMENT to access or utilize the services or functionality of

Microsoft Windows Server products (such as Microsoft Windows Server 2003), or
use the EQUIPMENT to permit workstation or computing devices to access or utilize

D-10
 Warranty
MICROSOFT CORPORATION EMBEDDED SOFTWARE END USER LICENSE AGREEMENT

the services or functionality of Microsoft Windows Server products, you may be

required to obtain a Client Access License for the EQUIPMENT and/or each such
workstation or computing device. Please refer to the end user license agreement for
your Microsoft Windows Server product for additional information.

4. NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT.

IPG HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE
IN THE EQUIPMENT, AND MS HAS RELIED UPON IPG TO CONDUCT
SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS
SUITABLE FOR SUCH USE.

5. NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided

"AS IS" and with all faults. THE ENTIRE RISK AS TO SATISFACTORY
QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK
OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY
AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE
OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY
WARRANTIES REGARDING THE EQUIPMENT OR THE SOFTWARE,
THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT
BINDING ON, MS.

6. No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW, MS

SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE.
THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS
ESSENTIAL PURPOSE. IN NO EVENT SHALL MS BE LIABLE FOR ANY
AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLARS
(U.S.$250.00).

7. Restricted Uses. The SOFTWARE is not designed or intended for use or resale
in hazardous environments requiring fail-safe performance, such as in the operation
of nuclear facilities, aircraft navigation or communication systems, air traffic control,
or other devices or systems in which a malfunction of the SOFTWARE would result
in foreseeable risk of injury or death to the operator of the equipment or system, or
to others.

8. Limitations on Reverse Engineering, Decompilation, and Disassembly. You may

not reverse engineer, decompile, or disassemble the SOFTWARE, except and only
to the extent that such activity is expressly permitted by applicable law
notwithstanding this limitation.

9. SOFTWARE as a Component of the Equipment-Transfer. This license may not

be shared, transferred to or used concurrently on different computers. The
SOFTWARE is licensed with the EQUIPMENT as a single integrated product and
may only be used with the EQUIPMENT. If the SOFTWARE is not accompanied by

D-11
Warranty
MICROSOFT CORPORATION EMBEDDED SOFTWARE END USER LICENSE AGREEMENT

EQUIPMENT, you may not use the SOFTWARE. You may permanently transfer all
of your rights under this EULA only as part of a permanent sale or transfer of the
EQUIPMENT, provided you retain no copies of the SOFTWARE. If the
SOFTWARE is an upgrade, any transfer must also include all prior versions of the
SOFTWARE. This transfer must also include the Certificate of Authenticity label.
The transfer may not he an indirect transfer, such as a consignment. Prior to the
transfer, the end user receiving the SOFTWARE must agree to all the EULA terms.

10. Consent to Use of Data. You agree that MS, Microsoft Corporation and their
affiliates may collect and use technical information gathered in any manner as part
of product support services related to the SOFTWARE. MS, Microsoft Corporation
and their affiliates may use this information solely to improve their products or to
provide customized services or technologies to you. MS, Microsoft Corporation and
their affiliates may disclose this information to others, but not in a form that
personally identifies you.

11. Internet Gaming/Update Features. If the SOFTWARE provides, and you choose
to utilize, the Internet gaming or update features within the SOFTWARE, it is
necessary to use certain computer system, hardware, and software information to
implement the features. By using these features, you explicitly authorize MS,
Microsoft Corporation and/or their designated agent to use this information solely to
improve their products or to provide customized services or technologies to you. MS
or Microsoft Corporation may disclose this information to others, but not in a form
that personally identifies you.

12. Internet-Based Services Components. The SOFTWARE may contain

components that enable and facilitate the use of certain Internet-based services. You
acknowledge and agree that MS, Microsoft Corporation or their affiliates may
automatically check the version of the SOFTWARE and/or its components that you
are utilizing and may provide upgrades or supplements to the SOFTWARE that may
be automatically downloaded to your EQUIPMENT. Microsoft Corporation or their
affiliates do not use these features to collect any information that will be used to
identify you or contact you. For more information about these features, please see
the privacy statement at http://go.microsoft.com/fwlink/?LinkId=25243.

13. Links to Third Party Sites. You may link to third party sites through the use of
the SOFTWARE. The third party sites are not under the control of MS or Microsoft
Corporation, and MS or Microsoft are not responsible for the contents of any third
party sites, any links contained in third party sites, or any changes or updates to third
party sites. MS or Microsoft Corporation is not responsible for webcasting or any
other form of transmission received from any third party sites. MS or Microsoft
Corporation are providing these links to third party sites to you only as a convenience,
and the inclusion of any link does not imply an endorsement by MS or Microsoft
Corporation of the third party site.

D-12
 Warranty
MICROSOFT CORPORATION EMBEDDED SOFTWARE END USER LICENSE AGREEMENT

14. Notice Regarding Security. To help protect against breaches of security and
malicious software, periodically back up your data and system information, use
security features such as firewalls, and install and use security updates.

15. No Rental/Commercial Hosting. You may not rent, lease, lend or provide
commercial hosting services with the SOFTWARE to others.

16. Separation of Components. The SOFTWARE is licensed as a single product. Its

component parts may not be separated for use on more than one computer.

17. Additional Software/Services. This EULA applies to updates, supplements, add-

on components, product support services, or Internet-based services components
("Supplemental Components"), of the SOFTWARE that you may obtain from IPG,
MS, Microsoft Corporation or their subsidiaries after the date you obtain your initial
copy of the SOFTWARE, unless you accept updated terms or another agreement
governs. If other terms are not provided along with such Supplemental Components
and the Supplemental Components are provided to you by MS, Microsoft
Corporation or their subsidiaries then you will be licensed by such entity under the
same terms and conditions of this EULA, except that (i) MS, Microsoft Corporation
or their subsidiaries providing the Supplemental Components will be the licensor
with respect to such Supplemental Components in lieu of the "COMPANY" for the
purposes of the EULA, and (ii) TO THE MAXIMUM EXTENT PERMITTED BY
APPUCABLE LAW, THE SUPPLEMENTAL COMPONENTS AND ANY (IF
ANY) SUPPORT SERVICES RELATED TO THE SUPPLEMENTAL
COMPONENTS ARE PROVIDED AS IS AND WITH ALL FAULTS. ALL
OTHER DISCLAIMERS, LIMITATION OF DAMAGES, AND SPECIAL
PROVISIONS PROVIDED BELOW AND/OR OTHERWISE WITH THE
SOFTWARE SHALL APPLY TO SUCH SUPPLEMENTAL COMPONENTS. MS,
Microsoft Corporation or their subsidiaries reserve the right to discontinue any
Internet-based services provided to you or made available to you through the use of
the SOFTWARE.

18. Recovery Media. If SOFTWARE is provided by IPG on separate media and

labeled "Recovery Media" you may use the Recovery Media solely to restore or
reinstall the SOFTWARE originally installed on the EQUIPMENT.

19. Backup Copy. You may make one (1) backup copy of the SOFTWARE. You
may use this backup copy solely for your archival purposes and to reinstall the
SOFTWARE on the EQUIPMENT. Except as expressly provided in this EULA or
by local law, you may not otherwise make copies of the SOFTWARE, including the
printed materials accompanying the SOFTWARE. You may not loan, rent, lend or
otherwise transfer the backup copy to another user.

20. End User Proof of License. If you acquired the SOFTWARE on a EQUIPMENT,
or on a compact disc or other media, a genuine Microsoft "Proof of License"/
Certificate of Authenticity label with a genuine copy of the SOFTWARE identifies

D-13
Warranty
MICROSOFT CORPORATION EMBEDDED SOFTWARE END USER LICENSE AGREEMENT

a licensed copy of the SOFTWARE. To be valid, the label must be affixed to the
EQUIPMENT, or appear on IPG's software packaging. If you receive the label
separately other than from IPG, it is invalid. You should keep the label on the
EQUIPMENT or packaging to prove that you are licensed to use the SOFTWARE.

21. Product Support. Product support for the SOFTWARE is not provided by MS,
Microsoft Corporation, or their affiliates or subsidiaries. For product support, please
refer to IPG support number provided in the documentation for the EQUIPMENT.
Should you have any questions concerning this EULA, or if you desire to contact
IPG for any other reason, please refer to the address provided in the documentation
for the EQUIPMENT.

22. Termination. Without prejudice to any other rights, IPG may terminate this
EULA if you fail to comply with the terms and conditions of this EULA. In such
event, you must destroy all copies of the SOFTWARE and all of its component parts.

23. EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to

U.S. and European Union export jurisdiction. You agree to comply with all applicable
international and national laws that apply to the SOFTWARE, including the U.S.
Export Administration Regulations, as well as end-user, end-use and destination
restrictions issued by U.S. and other governments. For additional information see
http://www.microsoft.comexporting.

D-14
 E

Product Returns
Returns to the United States
All product returns require a Return Merchandise Authorization (RMA) from IPG.

To obtain an RMA, call the Customer Service department of IPG Photonics Corpo-
ration at 508-373-1100 (US) or +49 2736 44 20 451 (Germany).

If you return a product with a RMA, please perform the following procedure:
1. Products must be carefully packed in a suitable shipping container(s). Buyer
assumes all responsibility for products damaged in shipment to IPG.
2. Buyer must issue a purchase order for the value of the replaced parts/service
items and IPG will issue credit or invoice when the parts/service is received.
Speak to IPG Service Manager for the amount authorized under the required
purchase order.
3. All requests for repair or replacement under this warranty must be made to IPG
within 30 days after discovery of the defect (but not later than 7 days after
warranty expiration).
4. All products returned to IPG but which meet applicable specifications, not
defectively manufactured or used not in accordance with this User's Guide, will
result in the Buyer being charged IPG's standard examination charge.
5. Complete packing list with product model and serial number will ensure prompt
repair.
6. Be sure to include with the returned product your 'ship to' address for the return
of the serviced product.

E-1
Product Returns
Returns to the United States

Shipping Instructions:
Warranty Returns
Domestic & International Buyers* pay for one-way freight costs and insurance to
IPG. IPG will pay for freight return cost and insurance back to the Buyer.

Non-Warranty Returns
Domestic & International Buyers* pay for two-way freight costs and insurance to
IPG. If shipment consists of returns that are both warranty and non-warranty, the
shipment will be considered as non-warranty.

Shipping address for returns to US:

IPG Photonics Corporation

50 Old Webster Road

Oxford, MA 01540

Attn: Product Returns

Tel: 508-373-1100

E-2
 Product Returns
Returns to Germany

Returns to Germany
Shipping address for returns to Germany:

IPG Laser GmbH

Siemensstrasse 7

D-57299 Burbach, Germany

Attn: Product Returns

Tel: +49-(0)2736-44-20-451
1. IPG Laser GmbH will only accept returns for which an approved Return Material
Authorization (RMA) has been issued by IPG Laser GmbH. You should address
to the customer support team at +49-(0)2736-44-20-451 or support.europe@ipg-
photonics.com to discuss the return and request an RMA number. You must
return defective products freight prepaid and insured to IPG Laser at the address
shown herein. All products which have returned to IPG Laser but which are
found to meet all previously applicable specifications for such products or which
indicate damage to the fiber connectors not resulting from defect manufacturing,
shall be subject to IPG Laser' standard examination charge in effect at the time
and these costs shall be charged to the Buyer. All products returned to IPG Laser
which are not accompanied by an itemized statement of defects, shall be returned
to the Buyer at the Buyer's expense and IPG Laser shall not carry out any
evaluation of such products. IPG Laser warrants to Buyer that its services, labor
and replacement parts, assemblies and modules will be free of defects in material
and workmanship for ninety (90) days from the date of shipment or performance
of services.
2. Warranty Returns - Domestic & *International Buyers should pay for one-way
freight costs to IPG Laser. IPG Laser will reimburse Buyers for applicable
reasonable third-party freight costs and IPG Laser will pay for freight return cost
back to the Buyer.
3. Non-Warranty Returns - Domestic & *International Buyers are responsible for
two-way freight costs. If shipment consists of returns that are both warranty and
non-warranty, the shipment will be considered as non-warranty. Any UNAU-
THORIZED shipments billed to IPG Laser without authorization will be re-
invoiced to the Buyer. Confirming purchase orders are required for non-
warranty returns.

E-3
Product Returns
Returns to Germany

4. *International Returns must include applicable DUTIES AND TAXES, and you
must mark air bills with "RETURNED FOR REPAIR." In any event, where IPG
Laser accepts a shipment, IPG Laser will invoice to the Buyer for any charges
as stated above.
5. Returns for credit will not be accepted unless authorized in advance, in writing
by IPG Laser, in accordance with IPG Laser' Terms and Condition, including
the warranty provisions. In most cases, restocking fees will apply.
6. All returns must be packaged adequately to avoid damage during shipment.
7. Complete packing list with product model and serial number will insure prompt
repair, if the other terms of this form are followed.
8. See the IPG Terms and Conditions for the applicable warranty for the products
before you request the return of the products.
9. RMA number will expire 31 days after the date of issue. Thereafter, units
received in under the expired RMA number will result in a longer turnaround
time. Include a copy of the completed RMA form with the return of your unit(s).

E-4
 F

Glossary

°C Degrees centigrade or Celsius

°F Degrees Fahrenheit

 Lambda (wavelength symbol)

μs Microsecond = 10-6 second

Amp Amperes

AC Alternating current

ADC Analog-to-digital converter

ASCII American Standard Code for Information Interchange (U.S.

Government)

BTU British thermal unit

CAN Controller Area Network

CDRH Center for Devices and Radiological Health (U.S. Government)

CFR Code of Federal Regulation (U.S. Government)

cm Centimeters = 10-2 meters

CPU Central processing unit

CW Continuous wave (operating mode)

DC Direct current

EN European Norm

Hz Hertz or cycles per second (frequency)

kg Kilograms

kV Kilovolts = 103 volts

kW Kilowatts = 103 watts

F-1
Glossary

l Liters (volume)

lbs Pounds

IP Internet protocol

LD Laser diode

LCD Liquid crystal display

LED Light emitting diode

nm Nanometer = 10-9 meters

mA Milliamps = 10-3 amperes

mm Millimeter = 10-6 meters

MHz Megahertz = 106 Hertz

mrad Milliradian = 10-3 radians (geometry)

rms Root mean square or quadratic mean

QCW Quasi-Continuous wave (operating mode)

TCP Transmission control protocol

VAC Voltage alternating current

VDC Volts Direct Current

W Watts (power)

F-2
Index
Numerics L
7-pin connector pinouts … 2-23 Laser Model Designation Codes … 2-1
Local Control Mode … 2-4, 2-29
C
Certification … 2-3 M
cleaning procedures … C-1 Model Configurations … 2-1
Collimator … 2-10 model specifications … 2-10
Connecting Electrical Power … 2-16 Modulation Mode … 2-32
Continuous (CW) Operation Mode … 2-31
Control Modes
Local Mode … 2-29
O
Remote Mode … 2-29 Operation Control Modes … 2-29
Operation Modes
Continuous (CW) … 2-31
E Pulsed (QCW) … 2-31
Emission On Indicator … 2-4 Operation Sub-Modes … 2-32
Emission-On Indicator … 1-13 Optical Fiber Connector Inspection and Cleaning … C-1
E-Stop button … 2-4 Optical Output Fiber Terminations … 2-9
Ethernet TCP/IP Interface … 3-1 systems with a collimator … 2-10
External (Analog) Power Control … 2-32 systems with a connector … 2-9

F P
filter media … B-2 Product Returns … E-1
front panel view … 2-3, 2-4 Pulse Shaper
Functional Safety … 1-4 Ethernet connection … 4-12
fuses … B-2 exporting … 4-15
importing … 4-15
installing … 4-4
G menus … 4-18
Gate Mode … 2-32 Offline option … 4-14
RS-232 connection … 4-13
Pulse Waveform … 2-33
I Pulsed (QCW) Operation Mode … 2-31
Initial Power-Up Sequence … 2-24
Interface Commands … 3-2
Interface Wire Specification … 2-17 R
Interlock Safety Circuit … 2-18 rear panel view … 2-6, 2-7
Remote Control Mode … 2-4, 2-29
replacing filter media … B-2
K replacing fuses … B-2
Key Control … 2-24 returns … E-1
Keyswitch … 2-4 RS-232 Configuration … 3-1

Index – 1
S
Sequence Editing … 4-39
Service and Repairs … B-1
Standalone Mode … 2-32
system timing … 2-25

T
Touch-Screen Display … 2-4, 2-33
Troubleshooting … 5-1

U
Unpacking Instructions … 2-11
cardboard box … 2-11
wood crate … 2-14

Y
YLR-Series System
using … 2-16

2 – Index
To learn more, visit www.ipgphotonics.com

© Copyright 2015 IPG Photonics Corporation

This user guide and any data disclosed therein is the property March 2015
of IPG Photonics Corporation and its affiliates, and constitutes
and contains proprietary information. Neither receipt nor Part Number
possession of this document confers or transfers any right to P21-010106
duplicate, use, or disclose any information contained herein
except as expressly authorized in writing by IPG Photonics
Corporation. No representations and warranties are made
hereby, except in a binding purchase order.
Artisan Technology Group is an independent supplier of quality pre-owned equipment

Gold-standard solutions We buy equipment Learn more!

Extend the life of your critical industrial, Planning to upgrade your current Visit us at artisantg.com for more info
commercial, and military systems with our equipment? Have surplus equipment taking on price quotes, drivers, technical
superior service and support. up shelf space? We'll give it a new home. specifications, manuals, and documentation.

Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.

We're here to make your life easier. How can we help you today?
(217) 352-9330 I [email protected] I artisantg .com