CBI S17-8 s1
Material Standard 2014-05-06 1/ 5
0487100125-AC
COATINGS
METALLIC WIRE SPRINGS
Technical responsibility: bae2dy/CBI/QMM-MAT
Any origin identification mark present on this drawing is replaced by the one referred to under the norm 0204L61114
Standardization CBI/QMM-MAT Replaces edition: AB (and
responsibility: previously 5.J.01.12)
Created by: Hud2dy – CBI/QMM-MAT
Document language: EN
Change: Update previous CB standard by CBI template according to CBI S17-8
Change information: ECR number: 0999A01782 - AC
Translation Responsibility
Release date Source Language Target language Translated by
In case of doubt the original language edition of this Chassis Brakes International Standard applies.
The user must verify validity of edition prior to use. It may not be reproduced or given to third parties without company consent. © Chassis
Brakes International 2014 - All rights reserved , also regarding any disposal, exploitation, reproduction, editing, distribution, as well as the
event of applications for industrial property rights
Printed on 20190521 by KAA1PU - document not kept updated
CBI S17-8 s1
0487100125-AC 2014-05-06 2/ 5
CONTENTS
1 SCOPE 3
2 APPLICATION 3
3 COATING PROCESS AND DESIGNATION 3
3.1 Wire coating 3
3.2 Finishing step on components 3
4 REQUIREMENTS 3
Any origin identification mark present on this drawing is replaced by the one referred to under the norm 0204L61114
4.1 Appearance 3
4.2 Corrosion test 4
5 NORMATIVE REFERENCES 4
6 MANDATORY INFORMATION IN TECHNICAL DOCUMENTATION 5
7 APPROVAL 5
The user must verify validity of edition prior to use. It may not be reproduced or given to third parties without company consent ©
Chassis Brakes International 2014 - All rights reserved , also regarding any disposal, exploitation, reproduction, editing, distribution,
as well as the event of applications for industrial property rights
Printed on 20190521 by KAA1PU - document not kept updated
CBI S17-8 s1
0487100125-AC 2014-05-06 3/ 5
1 Scope
This standard defines designation, tests and requirements for springs made of hot dipped zinc base
coated wire with or without an additional finishing step on finished components in accordance with
0204Y81063 standard “Coatings against corrosion – General requirements”.
2 Application
The coatings defined in this standard are applied to increase corrosion resistance of springs.
Finishing step on components with CrVI (hexavalent chromium) is not authorized.
Only Cr III (trivalent chromium) finishing is authorized.
3 Coating process and designation
Any origin identification mark present on this drawing is replaced by the one referred to under the norm 0204L61114
The coatings mentioned in this standard are designed according overall process on wire and on
spring by the symbol of coating as follows:
Type of wire coating
Finishing on the component
3.1 Wire coating
Two types are defined:
Type A: Hot dipped galvanized in molten zinc bath
Type B: Hot dipped galvanized in molten zinc with aluminum bath
3.2 Finishing step on components
Two finishing conditions are defined*:
Finishing 1: without finishing step
Finishing 3: Cr III passivating + sealer
In finishing 3, a thin deposit of electroplating zinc before passivating step is allowed on component.
(* Finishing 2 (CrVI passivating) does not exist anymore.)
4 Requirements
4.1 Appearance
Coating shall be uniformly metallic grey for finishing 1 or silver for finishing 3.
The user must verify validity of edition prior to use. It may not be reproduced or given to third parties without company consent. ©
Chassis Brakes International 2014 - All rights reserved , also regarding any disposal, exploitation, reproduction, editing, distribution,
as well as the event of applications for industrial property rights
Printed on 20190521 by KAA1PU - document not kept updated
CBI S17-8 s1
0487100125-AC 2014-05-06 4/ 5
4.2 Corrosion test
Neutral salt spray test according to 0204Y81063.
Symbol of Salt spray duration
coating without red rust
Type A finishing 1 96 h
Type A finishing 3 200 h
Type B finishing 1 200 h
Type B finishing 3 200 h
Any origin identification mark present on this drawing is replaced by the one referred to under the norm 0204L61114
5 Normative references
The following documents are applicable in addition to this Chassis Brakes International-Standard.
With dated references solely the edition referred to applies. With undated references the last edition
of the indicated document applies (including all revisions). Intentionally cited historical standards are
additionally identified as „Type H“.
In case of any conflict between the referenced documents and this Chassis Brakes International-
Standard, this standard takes precedence.
No. Document number (edition date) Title Type1)
Coatings against corrosion – General
1 0204Y81063 Z
requirements
1)
Type: M = Document to be supplied; Z = Cited document; H = Historical document
The user must verify validity of edition prior to use. It may not be reproduced or given to third parties without company consent. ©
Chassis Brakes International 2014 - All rights reserved , also regarding any disposal, exploitation, reproduction, editing, distribution,
as well as the event of applications for industrial property rights
Printed on 20190521 by KAA1PU - document not kept updated
CBI S17-8 s1
0487100125-AC 2014-05-06 5/ 5
6 Mandatory information in technical documentation
Material definition: “symbol of coating” type and finishing according 4.2.
Material standard: 0487100125
CBI material code(s): According to the material code Excel table
7 Approval
Approvers
(First Name – Department Signature & approval date Edition
Name)
Hude Olivier CBI/QMM-MAT Signed - 06/05/2014 AC
Any origin identification mark present on this drawing is replaced by the one referred to under the norm 0204L61114
Lombry Roland CBI/QMM-MAT Signed - 07/05/2014 AC
Bauwens Denis CBI/QMM-MAT Signed - 14/05/2014 AC
The user must verify validity of edition prior to use. It may not be reproduced or given to third parties without company consent. ©
Chassis Brakes International 2014 - All rights reserved , also regarding any disposal, exploitation, reproduction, editing, distribution,
as well as the event of applications for industrial property rights
Printed on 20190521 by KAA1PU - document not kept updated
