Machine Translated by Google

SMART intelligent signal generator

Instructions

MR9270S

transparent

mA 1 IN 2 ILO 3 OK

IN T-ON OUT FN

Hz 4 mV 5 24V 6 +-

I-TY O-TY REST

Oh 7
1 RTD 11 TC8 9 0
1

EXIT

Smar t color generator

Machine Translated by Google Smart Signal Generator

What users need to know

Dear users, thank you for purchasing the products produced by Shanghai Lanyi Electronic Technology Co., Ltd.

Mr.Signal Series Smart Signal Generator: Smart. To get started with Smart

quickly, you need to master the following 4 points.

1. Check "Instrument Introduction" and "Instrument Technical Parameters" to understand the main functions of Smart

and signal types. 2.

Signal selection and signal mode, for example, select millivolt output, thermocouple

belongs to millivolt signal, then millivolt output and various thermocouple types are millivolt signal mode. 3. Two

methods of manipulating the output value of a signal. 4. Enter the window and pay attention to the operation

prompts at the bottom of the display.

Machine Translated by Google Smart Signal Generator

Contents: 1. Instrument Introduction ------------------------------------------ ----- 1 2.

Instrument technical parameters --------------------------------------- ------3 3. Basic
operation --------------------------------------- ----------4 4. Signal description
----------------------------------- --------------11 5. Programming output -----------------------------
------------------24 6. Preset value------------------------- ------------------------28 7. Signal
conversion --------------------- ----------------------------29 8. Real-time curve -----------------
-----------------------------------29 9. System Settings------------- ------------------------------------31
10. Modbus RTU --------- -------------------------------32 11.Modbus master station----------
---------------------------------34 12. Paperless recorder---------- -----------------------------------40
13. Routine maintenance -------- -----------------------------------------44
Machine Translated by Google Smart Signal Generator

1. Introduction to the

instrument 1.1Smart uses a high-speed ARM processor with powerful performance, and has a man-machine dialogue

interface that is easy to use. The following figure shows the structure of Smart.

COM OUTPUT IN- IN+

Various signal 24V Various signal

output modules input modules

mA, V, HZ, mA, V, HZ,
mV, ÿ, 24V mV, ÿ

Signal Generator Operation Panel

MODBUS RTU slave

320*240 basic application layer

TFT color
Modbus master, PID panel,
display
recorder, HART
Communication Interface

Extended application layer

Mr.Signal-Smart core layer

USB

virtual serial port

Firmware download

FLASH

14500 lithium
battery (900mA*2) Rs485
USB

-1-
Machine Translated by Google Smart Signal Generator

1.2 Practical function

introduction: Program output: the user can let the Smart signal automatically rise and fall output, there are two modes,

the first one: set the start point, end point, number of cycles, and then start working. The second

type: advanced mode, the signal changes are all set by parameters.

Preset value: 9 groups of commonly used signal values can be preset for quick output. Signal

conversion: input signal is converted into output signal, for example: input frequency signal is converted into current

signal, input range is 0-1000hz into 4-20mA. Real-time curve: It can display the change trend of

input and output signals in the form of a curve, the collection time of the curve can be set, and the curve can be

automatically displayed in the range of the maximum and minimum values within a certain period of

time. Engineering quantity display conversion: the signal is displayed as signal value or engineering quantity, and the signal

value corresponds to the engineering quantity linearly, for example: the signal of 4-20mA corresponds to 0-100, that is,

4mA corresponds to 0, 12mA corresponds to 50, and 20mA corresponds to 100, which can be passed

through the parameter Modify this range.

Modbus RTU remote control: It can communicate with configuration software or PLC through RS485 to realize online

setting of the output signal of the instrument and monitor the input signal of the instrument.

Modbus RTU master station: perform communication test, parameter setting, parameter copy, online monitoring and

other operations on slave devices with RS485 MODBUS interface. Instrument tool set: As the

function extension of the instrument, such as: simple paperless recorder, PID controller, etc., please pay attention to the

product website for details, and this manual does not describe it.

USB firmware upgrade: upgrade new firmware to expand new functions.

USB to Rs485: The instrument can be used as a USB to RS485 virtual serial port, WIN10

The following operating system needs to install the driver.

-2-
Machine Translated by Google
Smart Signal Generator

2. Instrument technical parameters

Output Signal Parameters Output

Signal Parameters Signal Range

Accuracy Resolution Model Range Accuracy Resolution Temperature Drift Coefficient Temperature Drift Coefficient
Current (mA) Current Internal impedance Internal

(mA) impedance 100ÿ 100ÿ

0~24mA 0~24mA 0.05% 0.05% 0.01mA 0.001mA +25PPM +25PPM

500k 500k 100ÿ 100ÿ

Voltage (V) Voltage (V) 0~12V 0~12V 0.05% 0.05% 0.01V 0.001V +25PPM +25PPM

Passive (XMT) Passive (XMT) 0~24mA 0~24mA 0.1% 0.1% 0.01mA 0.001mA +25PPM +25PPM

24V Loop 24V Loop 0~24mA 0~24mA 0.1% 0.1% 0.01mA 5 digits +25PPM +25PPM 100ÿ 100ÿ

Frequency (Hz) Frequency 0~9999Hz 0~9999Hz 0.03% 0.03% 0.1mV 0.01mV +10PPM 1Mk 1Mk

(Hz) Millivolt (mV) Millivolt -10~110mV -10~110mV 0.05% 0.05% +25PPM +25PPM 2K 2K

(mV) Thermocouple (TC-S) Thermocouple 0-1760ÿ 0-1760ÿ 0.2% 0.2% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

(TC-S) Thermocouple (TC-B) Thermocouple 0-1810ÿ 0-1810ÿ 0.5% 0.5% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

(TC-B) Thermocouple (TC-E) Thermocouple 0-990ÿ 0-990ÿ 0.2% 0.2% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

(TC-E) Thermocouple (TC-K) Thermocouple

0-1320ÿ 0-1320ÿ 0.2% 0.2% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

(TC-K) Thermocouple (TC-R) Thermocouple 0-1760ÿ 0-1760ÿ 0.3% 0.3% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

(TC-R) Thermocouple (TC-J) Thermocouple 0-1190ÿ 0-1190ÿ 0.3% 0.3% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

Couple (TC-J) Thermocouple (TC-T)

0-390ÿ 0-390ÿ 0.2% 0.2% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

0-1290ÿ
Thermocouple (TC-T) Thermocouple (TC-N) Thermocouple 0-1290ÿ
(TC-N) 0.2% 0.2% 1ÿ 1ÿ +25PPM +25PPM 2K 2K

------
Pt100 Pt100 -200~650ÿ -200~650ÿ 0.5% 0.5% 1ÿ 1ÿ +50PPM +100PPM

Cu50 Cu50 ---

-20~150ÿ -20~150ÿ 0.5% 0.5% 1ÿ 1ÿ +50PPM +100PPM

Input Signal Parameters Output Signal Parameters

Range Accuracy
Model Resolution Signal Range Accuracy

Resolution Temperature Drift Coefficient Temperature Drift Coefficient Current (mA) Current (mA) 0.01mA 0.01mA +25PPM Voltage (V) Voltage (V) Frequency (Hz) Frequency
millivolt ((mV)
Hz) millivolt (mV)
Internal Impedance Internal

Impedance 100ÿ 100ÿ

0~24mA 0~24mA 0.1%
500k 500k
0~12V 0~12V 0.1% 0.001V +25ppm
0~9999Hz 0~9999Hz 0.1% 5 +10PPM 1Mk 1Mk

-10~110mV -10~110mV 0.1% digits 0.01mV +25ppm 2mk

Thermocouple (TC-S) Thermocouple (TC-S)
0-1760ÿ 0-1760ÿ 0.2% 0.2% 1°C 1°C 1°C +25ppm 2mk
Thermocouple (TC-B) Thermocouple (TC-B)
0-1810ÿ 0-1810ÿ 0.5% 1°C 1°C 1°C +25ppm 2mk
Thermocouple (TC-E) Thermocouple (TC-E)
0-990ÿ 0-990ÿ 0.2% 0.2% +25ppm 2mk
Thermocouple (TC-K) Thermocouple Couple 0-1320ÿ 0-1320ÿ 0.2% 0.2% 1ÿ 1ÿ +25ppm 2mk
(TC-K) Thermocouple (TC-R) Thermocouple 0-1760ÿ 0-1760ÿ 0.2% 0.3% 1ÿ 1ÿ +25PPM +50PPM 2Mk 2K
(TC-R) Thermocouple (TC-J) Thermocouple (TC-J)
0-1190ÿ 0-1190ÿ 0.2% 1ÿ 1ÿ +25ppm 2mk

-3-
Machine Translated by Google Smart Signal Generator

Thermocouple (TC-T) Thermocouple (TC-T)

0-390ÿ 0-390ÿ 0.2% 0.2% 1ÿ 1ÿ +25ppm 2mk

Thermocouple (TC-N) Thermocouple (TC-N) 0-1290ÿ 0-1290ÿ 0.2% 0.2% 1ÿ 1ÿ +50PPM +25PPM 2K
2Mk
Pt100 Pt100 -200~650ÿ -200~650ÿ 0.1% 0.5% 1ÿ
0.1ÿ +50PPM +100PPM 2.5k
---

Cu50 -20~150ÿ -20~150ÿ 0.5% 0.1% 1ÿ

0.1ÿ +50PPM +100PPM 2.5k
---

Cu50 resistance input 0-400ÿ 0.1% 0.01ÿ +50PPM 2.5k

3. Basic operation
3.1 Interface

definition Input-/(24V)
output + output Input+

MR9270S

transparent

mA 1 IN 2 ILO 3 OK

IN T-ON OUT FN

Hz 4 mV 5 24V 6 +-

I-TY O-TY REST

Oh 7
1 RTD 11 TC8 9 0
1

EXIT

Smar t color generator

USB charging port Rs485 communication interface

charging indication switch

-4-
Machine Translated by Google Smart Signal Generator

3.2 Keypad definition

I-TY
Output signal selection
Output signal on and off
This key has a secondary function. In

Input signal selection Function/Menu key the menu interface, this key is the

confirmation and modification key.

mA 1 IN 2 ILO 3 OK

IN T-ON OUT FN Clear the value of the

Hz 4 mV 5 24V 6 +-

input signal mode output signal mode

I-TY O-TY REST
Oh 7 1 RTD 8 11 TC 9 1
0

EXIT Menu exit direction key: used to select the option to be set or modify

the value.

3.3 Description of working interface Status Bar

Output signal

set value

Input signal

display value
real time curve

3.4. Select signal:

Press OUT once to pop up the output signal selection interface, and then Press IN once to pop up the input signal selection interface, and then press the

press the position of the keyboard to select the corresponding signal. position of the keyboard to select the corresponding signal.

-5-
Machine Translated by Google
Smart Signal Generator

3.5. Output signal:

Press the left and right keys to move the cursor to select the digit to be set, and

press the up and down keys to modify the value.

This key is the signal switch key, be sure to press this key
T-ON

makes the signal output start.

3.6. Enter the setting window:

3.6.1 Press and hold for OUT

two seconds and the instrument will pop up the output signal setting 3.6.2 Press and hold for two
IN seconds and the instrument will pop up the output

window. The following figure takes the current setting window as an example. signal setting window. The following figure takes the current setting window as

an example

3.6.3 Press FN once and a menu window will pop up

-6-
Machine Translated by Google Smart Signal Generator

3.7. Window control operation:

Press to select a menu item, press to modify

I-TYand confirm, press to exit or return to EXIT
the previous menu. 3.7.1
Modify the value: Select the control to be set and press, the control becomes modifiable. At this time, press the
up, down, left, and right keys to modify. After the modification is completed, press OK to save. Most controls are
modified in the same way. I-TY

I-TY

3.7.2 Modify the slider:

select the slider to be set, press the slider O-TYto move to the right, each
I-TYto move to the left, press the slider
modification, the slider is automatically saved.

3.8 Display interface switching

Press and hold the key EXIT for 2 seconds to switch between 5 different interfaces, and the following are the other four interfaces.

Output signal screen Input signal screen

Input real-time curve Input and output real-time curves

-7-
Machine Translated by Google Smart Signal Generator

3.9 Using the Numeric Keypad Window

Short key EXIT on the working interface will pop up the numeric keypad window, and the 12 buttons on the numeric keypad

window correspond to the 12 physical keys of the Smart, which are used to quickly set the signal output value. Short press to

realize the first function of the button, and long press to realize the second function, such as long press the number '1' to input a

negative sign.

Numeric keypad layout

4. Signal description

4.1 Current signal output 4.1.1

Current output mode: press O-TY to change the mode.

Current value output Engineering volume output

T-ON
4.1.2 Current signal open circuit detection: Press to start the signal output, if the interface shows open circuit and flashes,

it means the signal is not connected or the output is zero.

4.1.3 Current output setting window: Press and hold OUT for two seconds to pop up a window.

-8-
Machine Translated by Google Smart Signal Generator

Mode: Set the output value display mode. Loop

voltage: Set the current output no-load voltage, the default is 16.5V in order

to save power, some devices must require 24V drive capability. Quantity

setting: set the engineering volume range. Range: Set

the range of current output, select USER to set a custom

range.

4.1.4 Current output wiring.

meter or
+ PLC

output- output+

4.2 Voltage signal output

4.2.1 Voltage output mode: Press O-TY to change the mode.

Voltage value output Engineering volume output

4.2.2 Voltage output setting window: Press and hold OUT for two seconds to pop up a window.

-9-
Machine Translated by Google Smart Signal Generator

Mode: Set the output value display mode. Quantity

setting: set the engineering volume range. Over-

current protection: If the output voltage is short-circuited for 2 seconds, the

output will automatically shut down Range: Set the

range of voltage output, select USER to set a custom range.

4.2.3 Voltage output wiring.

meter or
+ PLC

output- output+

4.3 Passive current signal output (transmitter simulation)

4.3.1 Passive current output mode: Press O-TY to change the mode.

Passive current value output Engineering volume output

4.3.2 Passive current output setting window: press and hold OUT for two seconds to pop up a window.

-10-
Machine Translated by Google Smart Signal Generator

Mode: Set the output value display mode.

Quantity setting: set the engineering volume
range. Range: Set the range of passive current output, select
USER to set a custom range.

4.3.3 Passive current output wiring.

input+
Passive output (XMT) output to digital display
null enter- instrument/PLC/isolation safety barrier and other equipment

24V

output- output+

4.4 Pulse signal

4.4.1 The pulse signal has four modes: press two O-TY seconds to switch modes.

frequency output PWM duty cycle output

Speed frequency output Pulse quantitative output

-11-
Machine Translated by Google Smart Signal Generator

4.4.2 Pulse output setting window: Press and hold OUT for two seconds to pop up a window.

Mode: Set the pulse output mode. Range:

Select the range of frequency output Peak: The level

height of the output waveform, the highest is 24V.

Mode: level output (PNP) and open switch output

(NPN). Speed setting: enter the speed setting window.

Range setting: set the engineering range (only

frequency mode has this function.

4.4.3 Pulse Signal Operation Instructions - Frequency

Mode. Frequency is the most commonly used signal in the

pulse signal. It has four ranges. You can enter the pulse

output setting window to set the range or short press to

switch. 4.4.4 Pulse signal

O-TYoperation instructions - PWM

mode.

PWM is the abbreviation of Pulse-Width Modulation , PWM = 30%

which is the time ratio of the level on and on in a

pulse period. It can be clearly seen from the picture

that PWM requires two parameters. The first choice for

Frequency value (period)
outputting PWM is to set the frequency value, that is,

the period value. The setting method is to short press the

digital O-TY
tube of the frequency value to be selected by the

cursor. After setting the frequency value, press again O-TY

Returns PWM adjustment.

The main purpose of PWM:

Pulse heating, motor speed adjustment, light brightness, magnetic powder clutch braking strength, etc. It

has a wide range of uses and is the best solution for linear drive.

-12-
Machine Translated by Google
Smart Signal Generator

4.4.5 Pulse signal operation instructions - speed mode.

The best way to calculate the speed of the motor or gear is

the pulse method. The motor usually takes minutes as the

time unit. If the motor rotates one cycle and generates 1

pulse, which is 3000 revolutions per minute, then 1 second is

50 pulses. Frequency = RPS (per second) * number of pulses

per revolution RPM (per minute) = RPS * 60 RPH (per hour)

= RPS * 3600 This function is used to simulate the pulse

generated by the motor or gear rotation, the user only needs

to set the pulse per revolution The instrument will automatically

calculate the corresponding frequency value, the maximum

value is 9999H, and the calculation will stop if it exceeds

Missing teeth
9999H . Missing gear: mainly used to simulate engine speed.
...
For example: 60 teeth can be made in one rotation of the engine gear, but only 59 teeth are made, and one tooth

position is vacant, and the rotational speed is measured by this missing tooth. 4.4.6 Pulse signal operation
instructions - Quantitative mode. The main purpose of pulse quantification is to simulate flow quantitative control

sensors. For example, a turbine sensor generates 100 pulses after one liter of water flows through the sensor, then 10

liters of water is 1000 pulses. When writing a PLC quantitative program, the generator can be used to accurately

simulate .

The unit of the sending cycle of a

single pulse is milliseconds, the

minimum is 0.1mS

Quantitative pulse number working status

The transmission cycle timing time

The progress of the number of remaining pulses The progress of the remaining sending
schedule of a single pulse.
time is max 99:99:99

-13-
Machine Translated by Google Smart Signal Generator

Quantitative Operation Instructions:

Quantitative mode working

state Stop: Only in this state can the number of

quantitative pulses be modified Pause: Pause and

wait for commands. Run: Pulses start to be sent.

Press this key to change from stop state to pause, which means ready
T-ON
to start working. Press this key in pause state, the pulse will start to
send.
IN T-ON OUT FN
Hz 4 mV 5 24V 6 +- Press this key in the running state, and the pulse transmission will be paused.
I-TY O-TY REST
Oh 7 1 RTD 8 11 TC 9 1
0 Press this key in the running state to send pulses individually.
EXIT
REST Press this key in the running state, the program stops and resets.

O-TY Press this key in any state to modify the cycle time.

4.4.7 Pulse signal wiring instructions.

meter or
+
PLC

output- output+

level output

Positive power supply

resistance
Open collector output frequency output

Negative pole of power supply

instrument or PLC

-14-
Machine Translated by Google
Smart Signal Generator

4.5 mV/thermocouple signal

4.5.1 mV output mode: press O-TY to change the mode.

Millivolt output thermocouple analog output 4.5.2 Millivolt output setting window:

press and hold OUT for two seconds to pop up a window.

Mode: Set the output value display mode. Range

setting: set the engineering range (only available in millivolt

mode). Type: Select the type of

thermocouple. Reference Temperature: The reference

temperature for cold junction compensation. Temperature Units:

Set to Celsius or Fahrenheit.

Why do thermocouples need cold junction compensation?

Thermocouples work on site, and measuring instruments generally work indoors. The
temperature difference between the two is large. Since the signal measured by the
thermocouple is based on 0, the thermocouple The signal is weak. In order to transmit

the signal to the measuring instrument end stably, a special compensation lead wire must be used. However, the compensation lead wire enters the point where
the instrument is located and superimposes the temperature transmitted back to the room. Therefore, the superimposed thermoelectric potential must be
removed by cold junction compensation. Let the thermocouple signal be accurately restored. Therefore, during the test, it is found that the temperature displayed
by the instrument does not match the actual temperature or is too high, which means that the temperature of the cold end needs to be set, which is the indoor
temperature.

4.5.3 mV output wiring.

meter or
+ PLC

output- output+

-15-
Machine Translated by Google Smart Signal Generator

4.6 Resistance signal

4.6.1 Resistance output mode: Press O-TY to change the mode.

Resistance RTD analog output

output 4.6.2 Resistance output setting window: Press and hold OUT for two seconds to pop up a window.

Temperature unit: Celsius and Fahrenheit Switching

type: Type selection of thermal resistance Resistance

offset: Correct the output resistance.

4.6.3 Resistance output wiring.

meter or
+ PLC

output- output+

Precautions for RTD testing: RTD

signal has a special specific effect, it is not an electrical signal, so the Smart analog resistance signal has certain requirements, and the
detection terminal of the instrument will generally output a voltage for the heating resistor to change the current and voltage with temperature
changes. The voltage cannot exceed 10V, otherwise the thermal resistance simulation will fail. The instrument is generally 1.2V to 7V. If you
find that the thermal resistance cannot be simulated, you can connect the thermal resistance output signal to the generator input for inspection.
If it is normal, then check the detection of the instrument end. Usually the detection terminal voltage will not exceed 5V, and the current is
within 1mA, because if the measured voltage is too high or the current is too large, the output power will increase accordingly, which will
cause the thermal resistance sensor to heat itself, resulting in unstable or shortened temperature measurement. life.

-16-
Machine Translated by Google Smart Signal Generator

4.7 24V loop detection (transmitter power supply and current detection are shared with the output port) 4.7.1

24V feedback current display mode: Press O-TY to switch modes.

Feedback current value display Engineering volume output

4.7.2 24V setting window: Press and hold OUT for two seconds to pop up a window.

Mode: Set the output value display mode. Range

setting: set engineering volume range.

4.7.3 Wiring instructions.

There are many types of transmitters, such as: pressure

transmitters, temperature transmitters, pneumatic valve feedback

Transmitter - + transmitters, and so on. The power supply current of the test equipment

cannot be greater than 24mA, please select the equipment for testing.

output- output+

-17-
Machine Translated by Google Smart Signal Generator

4.8 Independent 24V

4.8.1 Understand independent 24V.

The input (-) can be switched to an independent 24V function, which outputs a single 24V. The 24V

terminal is used in conjunction with the input (+) to test the transmitter. Its main use is to test pneumatic

control valves or two-wire transmitters.

output - output + input - input + Tip: The difference between 24V loop detection and independent

24V is that the 24V loop detection uses the output signal port to

ÿÿÿ
ÿÿÿ measure the feedback current. The independent 24V port and

activation the output (-) port can form a 24V power supply, and can also
form a transmitter power supply and measure with the input (+).
ÿÿÿÿÿÿ
The feedback current of the transmitter.
4.8.2 Turn on the independent 24V.

Enter the function menu and choose to activate 24V, the status bar will display 24V prompt and flash

24V activation: After this item is ticked, the independent 24V starts to output.

Activation hold: After this item is ticked, every time it is turned on, the 24V state

will remain at the state of the last time it was turned on. On the contrary, the 24V

needs to be turned on manually every time it is turned on.

4.8.3 Wiring method.

Pay attention to the wiring method of the independent 24V test two-wire transmitter, the "independent 24V"

terminal is connected to the positive pole, and the input (+) is connected to the negative pole .

Transmitter 1 Transmitter
2 (-) (+) (+) (-)

output- output+ 24V input + output- output+ 24V input+

active separate Activate independent

current output 24V loop detection
24V current input 24V current input

Pneumatic control valve test Simultaneously test two 2-wire transmitters

-18-
Machine Translated by Google Smart Signal Generator

4.9 Current input

4.9.1 Current input display mode: Press to switch modes.

I-TY

Current input display Engineering quantity input display

4.9.2 Current input setting window: Press and hold forINtwo seconds to pop up a window.

Mode: Set the input value display mode. Range

setting: set engineering volume range.

4.9.3 Wiring instructions.

The maximum range of current input is

-
24mA, and the constant current measurement method
+ various sensors
is adopted, so there are positive and negative poles,

and the voltage within 30V will not burn out the input

input - input + port.

-19-
Machine Translated by Google
Smart Signal Generator

4.10 Voltage input

I-TY
4.10.1 Voltage input display mode: Press to switch modes.

Voltage input display Engineering quantity input display

IN two seconds to pop up a window.

4.10.2 Voltage input setting window: Press and hold for

Mode: Set the input value display mode. Range

setting: set engineering volume range.

4.10.3 Wiring instructions.

+ various sensors

input - input +

The voltage input range is -4V~30V

-20-
Machine Translated by Google Smart Signal Generator

4.11 Pulse input 4.11.1

Pulse input display mode: Press to switch modes.

Frequency input mode PWM input mode

Frequency speed input mode pulse count

4.11.2 Pulse input setting window: Press and hold IN for two seconds to pop up a window.

Mode: Set the input value display mode. Speed

setting: The speed function of pulse input is the same

as that of pulse output.

Mode: input mode. Counting

method: The rising edge means that the level rises from

0V to the peak value of the pulse, and the

counter adds 1. The falling edge means that

the input level drops to 0V, and the counter

adds 1. The jump means that as long as the

input level jumps up and down, the counter

will add 1. To reset the counter, please press

REST ÿ

-21-
Machine Translated by Google Smart Signal Generator

4.11.3 Wiring instructions.

- Sensors with
PNP
frequency output
+
input - input +

The frequency input range is 0-9999HZ

Oc gate
frequency
-

output sensor

input - input +
Sensors with open-circuit output are common,
2.5V
such as turbine flowmeters, proximity switches,
2K resistor
etc., are tested with open-circuit input.

4.12 mV/thermocouple input

4.12.1 Millivolt input display mode: Press to switch modes.

Millivolt input mode Thermocouple input mode

-22-
Machine Translated by Google Smart Signal Generator

4.12.2 Millivolt input setting window: Press and hold IN for two seconds to pop up a window.

Mode: Set the input value display mode. Quantity

setting: set the engineering volume range. Type:

Select the type of thermocouple. Reference

Temperature: The reference temperature for cold junction

compensation. Temperature unit: Choice between Celsius and Fahrenhe

hint! The input setting of millivolts is exactly the same as

the output setting principle.

4.12.3 Wiring instructions.

+ thermocouple sensor

input - input +

4.13 Resistor/PT100/CU50 input

4.13.1 Display mode of resistance input: press switch I-TY to change the mode.

Resistance input mode RTD input mode

-23-
Machine Translated by Google
Smart Signal Generator

4.13.2 Resistance input setting window: Press and hold IN for two seconds to pop up a window.

Temperature unit: Celsius and Fahrenheit Switching

type: Select the type of thermocouple Line resistance:

Since the instrument uses a two-wire system to measure resistance,

there is no hardware compensation for line resistance, so this setting

can be used for software compensation.

4.13.3 Resistance input wiring.

Pt100/
Cu50

resistance

input - input +

5. Program output

The programming output can automatically complete N cycles according to the parameters set by the user. This
function is mainly used for aging tests of electric valves or pneumatic valves, or tests such as PLC program
adjustment.

5.1. As shown in the figure, set 4 parameters to quickly output the program.

Signal peak

value at 20mA

0mA back to the initial

0mA initial value
value time

Increase and decrease cycle The rising and falling process of the left figure is a cycle,
Run this cycle 100 times.

-24-
Machine Translated by Google Smart Signal Generator

5.2 Start programming output

Short press on the main interfaceFN

to pop up the function menu and select programming output.

Pop up the programming output window and select Start, and it will automatically return to the main interface, waiting for the user

to start and run.

status icon

Signal start point end point progress timing progress remaining times

Program running program reset indication of different states

stop
Hz 4 mV 5 24V 6 +-

I-TY O-TY REST run

Oh 7
1 RTD 8 11 TC 9 1 0

Single step (while paused) program exit

EXIT
suspend single run
program pause single run

-25-
Machine Translated by Google Smart Signal Generator

5.3. Advanced settings (the last item in the programming output window)

ÿÿÿÿÿÿ

Mode: There are two choices of cycle/custom.

Cycle: work according to the four

parameters set in the upper window.

Customization: work according to

the first three parameters of the upper menu

plus the six parameters of the

current window.

V1: initial value

V2: increase step value

T2
T1: Incremental stepping time

T2: End stop

v2
.. .. V4 V3: Endpoint value
v2 V4: minus step value
T1 V3 T3 T4 T3: minus step time
T1
T4: Loop stop
V1

Tip: After using the custom mode and setting the 6 parameters, when returning to the programming output window, the increase/
decrease cycle will be displayed and the increase/decrease cycle will be recalculated according to the user definition.

-26-
Machine Translated by Google Smart Signal Generator

5.4. Waveform Timing Generated by Custom Mode

For this waveform, the subtraction step value can be set to the entire

range, such as the start is 4mA, the end point is 20mA, and the

subtraction step value is set to 16mA so that 20-16=4, so that it is directly

reduced to the initial value.

0 T

rising sawtooth wave

It is the same as the rising sawtooth wave method, except that the incremental step value

is modified so that it can increase to the end value in one step.

0 T

falling sawtooth

By combining the rising sawtooth and the lower limit sawtooth,

it is enough to modify the dwell time at the end point.

0 T

Square wave output timing

-27-
Machine Translated by Google Smart Signal Generator

6. Preset value

6.1 Enter the preset window, short press on the main interface to pop
FN up the function menu and select Enable

preset.

6.2 Preset operation

After the preset is enabled, the keys on the left three columns of the keyboard are converted to the preset function,

and the right side can be used by pressing FN REST , and pressing EXIT to exit the preset function.

mA 1 IN 2 ILO 3 OK

Preset 1 Preset 2 Preset 3 FN

Hz 4 mV 5 24V 6 +-

Preset 4 Preset 5 Preset 6 REST

Oh 7
1 RTD 11 TC8 9 0
1

Preset 7 Preset 8 Preset 9 EXIT

-28-
Machine Translated by Google Smart Signal Generator

7. Signal conversion

During on-site debugging, if the debugged equipment does not match the secondary instrument, this situation can be solved
by signal conversion, for example, the frequency is converted from 0-100Hz to 4-20mA.

On the main interface, short press FN to pop up the function menu and choose to enable conversion.

Input lower limit/Input lower limit: The signal range of the input

signal. Output upper limit/output lower limit: the signal

range of the output signal. Overrun allowed: For example, 1-5V is

converted into 4-20ma, if the user checks this item, the

input is

When 0V, the output will follow 0mA, if the user does not

check it, then the output is 4mA, and the output is locked

within the set range. Enable at power-on: After checking this

item, the next time

It will automatically start the signal conversion when it is turned on, and if the key EXIT is pressed during the conversion work ,

the signal conversion will exit. The purpose of power-on activation: If the user wants to plug in the USB power supply for a

long time and work in the signal conversion mode, in order to avoid manually starting this function every time the machine is

restarted, this function is enabled. In order not to cause misoperation, just press once to exit, the instrument Run at startup

will be automatically unchecked.

8. The real-time curve is

used to analyze the changing trend of the signal.

8.1 Display large curve interface: In the main interface, press and hold for 2 seconds
EXIT to switch the interface, and the large
curve screen is on the 4th and 5th interfaces.

-29-
Machine Translated by Google Smart Signal Generator

auxiliary timer

Signal value scale

time scale

Input signal curve interface

Input signal output signal simultaneous working curve interface

8.2 Operation of real-time curve

Pause refresh of real-time curve: press and holdT-ON

for 2 seconds,PAUSE will appear in the real-time curve box

and flash, and the real-time curve will pause to refresh at this time, continue to press this button for 2 seconds, and

the real-time curve will start to refresh. Auxiliary timer reset: The auxiliary timer displays the running time of the

machine, long press the REST clock for 2 seconds to reset the timer. Please use this function flexibly in conjunction

with clearing.

-30-
Machine Translated by Google
Smart Signal Generator

FN up the function menu to select

8.3 Enter the real-time curve setting window: Short press on the main interface to pop

real-time curve.

Output Curve : Turn on the following display of the output signal

curve (yellow line). Automatic

scaling: Automatically adjust the scale range of the output signal, and

automatically adjust the scale range of the y-axis

with the maximum and minimum values of the

curve. Acquisition time: the refresh interval time of the output curve.

Auto Scale: The scale of the input signal is changed automatically.

Acquisition time: The refresh interval time of the input signal.

Tip: Modify the acquisition time, the time scale will change automatically, and the
time scale only follows the input signal acquisition time.

9. System Settings 9.1

Enter the system settings window

FNto pop up the function menu to select system settings.

Short press on the main interface

-31-
Machine Translated by Google
Smart Signal Generator

OUT selectIN"Turn" press

Signal switching: select "Quick" press or select signal,
OUT
Or IN
switch signals in turn. Operation

EXIT
interface: Select the work interface, which has the same effect as long pressing.

Backlight: Adjust the brightness of the backlight. Setting save: save the output value

set before shutdown. State preservation: the switch state of the output signal is

maintained, (if the signal is turned on every time the power is turned on, this item can be set, and it usually

works with signal conversion). Buzzer: Buzzer switch. Fast Acquisition: Improve the refresh rate of signal input.

Power supply and start: After plugging in the USB power supply, the instrument will automatically enter the

working state. If it is not checked, the instrument will remain on the charging interface after power on. If the

instrument is plugged into the USB port of the PC, and the driver is normal, the instrument will automatically

start up.

Theme: Change the color scheme of the instrument, using the environment or personal preference selection.

Fn long press function: Press andFN

hold for 2 seconds to quickly start the program function.

Calibration: Enter the fine-tuning window of the signal, please ensure that there is a high-precision multimeter or signal

source before entering this window.

10. The Modbus RTU slave station adopts

the standard Modbus RTU protocol, and can use configuration software or PLC for remote control and monitoring.

FN to pop up the function

10.1 How to enter the slave station port setting, short press on the main interface

menu and select port setting.

-32-
Machine Translated by Google Smart Signal Generator

10.2 Instrument register address and description

Post-tampering address data type attribute description

Command 40001 16-bit unsigned read and write has no function

Key 40002 The key pressed by the 16-bit unsigned read-write instrument

Value = 0 system default state, value = 1 enables program input mode

40003 16-bit unsigned read and write
output, value=2 is the signal conversion mode

battery power
40004 16-bit unsigned read-only instrument voltage
to press

Reserved 40005 16-bit unsigned read-only reserved

input letter Value=0 current input, value=1 voltage input, value=2 frequency
40006 16-bit unsigned read and write
number selection Rate input, value = 3 mV input, value = 4 resistor input.

Each signal is its own mode, the current voltage signal

The mode 1 of number is range display, the mode of frequency has =0

Input signal
40007 16-bit unsigned read and write is frequency = 1 is PWM, millivolt signal = 0 is millisignal mode

Volt, when =1 is a thermocouple, resistance input =0 is

Pt100,=1 is Cu50,=2 is resistance input.

input letter When frequency =, it is level input, when =1, it is NPN output
40008 16-bit unsigned read and write
number type Input, millivolt signal for thermocouple type switching.

input letter Large font display of

40009 32-bit signed read-only instrument input signals
value integer

-33-
Machine Translated by Google Smart Signal Generator

When the frequency signal is in PWM mode, this value is the frequency

input letter 32-bit signed value, for millivolt input, read-only for thermocouple input
40011

number value 2 integer , the value is the millivolt value of the input, the resistance input and the

Millivolt input functions the same as

input volume 32-bit signed read-only

40013 range converted from the input signal

about integer

input letter
40015 32-bit floating-point number read-only has the same function as integer display, but the floating-point

value

input letter
40017 32-bit floating-point number read-only has the same function as integer display, but the floating-point type

number value 2

input volume
40019 32-bit floating-point number read-only has the same function as the integer display, but the floating-point representation

about

Output open
40021 16-bit unsigned read and write output signal switch

close

value=0 current output, value=1 voltage output, value=2 none

Output signal
40022 16-bit unsigned read and write source output, value = 3 frequency output, value = 4 millivolt output.

number selection

Value = 5 thermal resistance output, value = 6 24V output

Each signal is its own mode, the current voltage signal

The mode 1 of number is range display, the mode of frequency has =0

Output signal

40023 16-bit unsigned read and write is frequency = 1 is PWM, millivolt signal = 0 is millivolt
number mode

Volt, when =1 is a thermocouple, resistance input =0 is

Pt100,=1 is Cu50,=2 is resistance input.

-34-
Machine Translated by Google
Smart Signal Generator

When the output signal frequency = 0, it is level input, when it is = 1, it is NPN input 40024 16-bit unsigned read-write number type input,
when it is millivolt signal, it is thermocouple type switching.

output letter 32-bit signed read-

40025 write instrument output signal display value in large font
value integer

When the frequency signal is in PWM mode, this value is the frequency

output letter 32-bit signed value, when millivolt output, in the case of thermocouple output read-only, this value is the
40027 output millivolt value, resistance output and
number value 2 integer

The millivolt output functions the same as

Output 32-bit signed

40029 Read only the range converted by the output signal

integer

Process
output signal 40031 32-bit floating-point reading and writing have the same function as integer display, but floating-point representation

Number

value output
signal 40033 32-bit floating-point number read-only has the same function as the integer display, but the floating-point display
Number

value 2
output 40035 32-bit floating-point number read-only has the same function as the integer display, but the floating-point display
about

11.Modbus master station -Mr.MOD The Modbus master station

function is an advanced function of this product and will be upgraded regularly. This instruction only explains the basic
operation. If there is an update, the staff will release it on WeChat, so stay tuned! The Modbus master station is mainly
used for on-site modification of instrument parameters, parameter copy monitoring, and testing whether the
communication is normal. The RS485 interface is used for the communication method, and it has three-pole protection
inside, which can prevent static electricity above 100V, and short-circuit protection, and PTC self-recovery insurance.

-35-
Machine Translated by Google Smart Signal Generator

11.1 The Modbus master station has 5 configurations for users to test different devices.

11.2 Modbus master main interface

Communication error count

Count Master Tag

Variable number

baud rate information

Variable Label Indicates variable

Variable Device Address value data type

Variable Address online

IN T-ON OUT FN

Corresponds to the first

row of keys on the keyboard

-36-
Machine Translated by Google Smart Signal Generator

11.3 Modbus Master Parameters and Modes

Press the setting key to enter the parameter setting of the master station.

The Modbus master station has two working modes to change the

communication parameters of the device. Automatic: The user triggers

the run button, and the program starts to poll the variables of the

slave station, refresh the variables in real time, and modify the

variables online. Manual: The read and write operations of the

program are performed manually, and the program will poll the slave

device once by pressing the read and write button. Modify the

parameters to be modified uniformly, press the write button, and the

program will automatically write the changed variables in sequence.

11.4 Adding a variable

Click the add button to pop up the add screen.

Device address: the range is 0-255

Command: Select the command sent to the slave

device. In the figure, 03:40x,03 represent

the protection register operation command,

and 40X represents the register address

prefix of the Modbus protocol. For example,

if the variable address is set to 00001, then

access The register address of the register

is 40001, and the hexadecimal address is

0000.

Number of additions: The number of variables to add, for example, if the number of additions is 10, then the variable address will be

automatically incremented.

-37-
Machine Translated by Google Smart Signal Generator

Variable type:
ushort: 16-bit unsigned integer short: 16-
bit signed integer

Byte-1: 8-bit first byte integer (the variables in the Modbus underlying protocol are all 16-bit data, if
the user wants to take an 8-bit integer, then the byte to take is selected by the user)

Byte-2: 8-bit second byte integer ulong:

32-bit unsigned integer long: 32-bit
signed integer
Float: 32-bit single-precision floating-point number

Commonly used labels and tags:

annotation role. Data arrangement: After the modbus master reads the variables, it rearranges them.

For example: a floating-point number is composed of four words. Because the

CPUs used by MODBUS slave devices are different, it may cause the four-byte
arrangement of the floating-point number to be different. This setting can be
modified. Add: After the setting is correct, you can move the cursor to the
confirmation key to add, or directly press Quick Add. OUT

11.5 Variable operation: On

the main interface of the Modbus master station, press I-TY to pop up the variable operation window.

-38-
Machine Translated by Google Smart Signal Generator

Edit value: Pop up the numeric keyboard for modification.

Variable properties: Pop up the same window as adding variables.

HEX/DEC: Switch between hexadecimal and numeric display. Device scanning:

Scan device addresses according to the selected variable attributes. Unified

Address: Set the device address of other variables to be the same as the address of the selected

variable. Delete: delete a variable. Delete All: Deletes all variables. Quickly modify the variable value:

press on the main interface of the MODBUS master station to pop up a numeric keyboard. Modify the

bit variable: press O-TY on the main interface of the MODBUS master station toO-TY
clear or set the bit.

11.6 Device Scanning: Scan for devices with unknown addresses. Access

via the Variables menu.

Start scanning : scanning needs variable address and instruction parameters, so before entering device scanning,

you must add a variable or use an existing variable. The scanning work screen only has the communication port setting

and the device address range setting. After moving the cursor to “Start Scanning” and pressing the scanning procedure,
I-TY
the scanning program will start immediately.

-39-
Machine Translated by Google Smart Signal Generator

Scanning process: If there is a device response, the corresponding address will be automatically filled in the address table, and the

number of returned devices will be displayed in the address table after the scan is completed. As shown in the figure, Dev=002 means

that only 001 and 002 respond from addresses 1 to 32.

Change the device address of the variable: If the variable device address you choose is 003, move the cursor

to the address table and press, select

I-TY the scanned device address and press it again, then the device address
I-TY
scanning window will automatically exit and modify the variable device address.

12. Recorder 12.1

Purpose: In the process of on-site debugging, if the occurrence time of the problem is uncertain, the

function of the recorder can be used to record the signal change trend in the form of a curve. After the

recording is completed, the historical data can be exported to the personal computer , print or screenshot for

analysis. 12.2 Parameter capacity: 20000 record points. Channel: 2. Recording interval: 0.1 seconds - 999.9

seconds.

-40-
Machine Translated by Google
Smart Signal Generator

12.3 Real-time Interface Description of Recorder

channel 1 value channel 2 value

current clock

Channel 2 scale
Channel 1 Scale

storage usage The keys here

correspond to the

upper two rows of

keys on the keyboard

12.4 Start recording

Before using the recorder, the setting of the signal source is the most important part, so first determine what

signal type to use as the signal source. For example: To record the temperature of a Pt100 temperature

sensor, the pressure range of a pressure transmitter is 0-100kpa. The wiring diagram is as follows:

Pressure
Transmitters
Pt100
-+

Output - Output Input

+ - Input +

-41-
Machine Translated by Google Smart Signal Generator

Back to the signal generator interface, the output is switched to 24V loop detection and the mode is range display ,

and the range is changed to 0-100.0 corresponding to 4-20mA. The input signal is switched to resistance input, and

the mode is switched to PT100 input. After the signal display is all normal, enter the function menu and then enter

the recorder.

After entering the recorder function, press FN to enter

the recorder configuration. Recording time: According

to user settings, the recorder will automatically calculate

the recording time. Recording interval: The larger the

interval, the longer the recording time will be.

Ch1 signal source: signal source setting, the device here is

output signal, 24V loop detection.

Ch2 signal source: set as input signal here, resistance

input PT100 input mode. Automatic range: MR9270S

curve displays 320 points on one screen. After enabling

this function, the Y axis of the curve will be displayed

within the range of the maximum value and minimum

value within 320 points.

-42-
 Machine Translated by Google
Smart Signal Generator

After configuring the parameters of the recorder, you can start recording. Press
IN it to pop up the time setting.

Since there is no clock battery inside the MR9270S, it must be set manually. After the setting is complete,

press the recorder again

IN to start recording. During the recording process, there will be a black dot flashing in

the upper left corner of the screen. If the black dot is not flashing and displayed, it means that the recorder has

completed a record.

ÿÿÿÿ

IN hold it for two seconds, and a black dot will appear on the
If you want to stop recording halfway, press and

upper left corner of the screen. Since the recorder can only record once, if you need to restart recording,

you must reset the recorder to restart recording. seconds will reset the logger. Historical data is very
REST

important. In order to avoid misoperation, it must be reset before starting again. 12.5 History Record Press

the interface to switch to the history record interface. When viewing the record, it should be noted that if the

recorder is recording and the recording interval is less than 1 second, please try not to switch back and forth

OUT the history record interface and the real-time interface many times, which may cause Data is lost
between

because switching CPUs takes time.

-43-
Machine Translated by Google
Smart Signal Generator

The time the cursor

moves one step at a time

The duration of
each grid

Lock Cursor: Make the cursor not move, only move the curve. Time

mark +/time mark -: change the time length of the first frame. Step+/

Step-: Change the length of each step the cursor moves, "Step-" is the down key on the keyboard.

12.6 History export

Log in to the product website to download the host computer software of the recorder, which is free for users to use. Since

the software will be updated, no explanation will be made here, and the website will have synchronously updated

instructions for use. Before connecting to the host computer, please set the communication mode to "USB Modbus".

13. Maintenance and troubleshooting.

Battery: Mr.Signal 2 uses two 14500 lithium batteries, each with a capacity of 900mA. The usage time depends
on the usage. You can use the timer on the main interface to know your own power consumption. When using the

USB interface to charge the battery, In the charging screen, the instrument charges the battery with a current of

1A, press the start button, and the instrument charges with a current of 500A in the main interface. If the instrument

is not used for a long time, the battery can be fully charged and then stored. The power consumption current after

the instrument is turned off is very small and basically negligible.

-44-
 Machine Translated by Google
Smart Signal Generator

Self-inspection: During on-site debugging, there are many kinds of difficult and miscellaneous diseases. Before testing, please
ÿÿÿÿ

confirm that the testing equipment is normal. The instrument can input and output at the same time, so you can test yourself to

ensure that it is normal before testing to ensure that you do not take detours. The site is complicated , there is no guarantee that the

port of the instrument is not damaged by strong electricity.

-45-