3EM23952AL

Issue 0.1, November 2012 PRELIMINARY

Table 7-L. Radio profiles: MPT-HC, static modulation

CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME
5 MHz 10 MHz 30 MHz 40 MHZ 50 MHz
Unlicensed 4 QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16 QAM 28.27 Mbps 87.45 Mbps
32 QAM 35.23 Mbps 108.75 Mbps
64 QAM 44.73 Mbps 138.02 Mbps
128 QAM 24.36 Mbps 52.69 Mbps 162.88 Mbps
256 QAM 60.30 Mbps 185.37 Mbps
Lower 6 GHz 4QAM 43.85 Mbps
16QAM 87.45 Mbps
32QAM 108.75. Mbps
64QAM 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
Upper 6 GHz 4QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16QAM 28.27 Mbps 87.45 Mbps
32QAM 35.23 Mbps 108.75. Mbps
64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
7/8 GHz 4QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16QAM 28.27 Mbps 87.45 Mbps
32QAM 35.23 Mbps 108.75 Mbps
64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
11 GHz 64QAM 44.73 Mbps 138.02 Mbps 186.97 Mbps
128QAM 52.69 Mbps 162.88 Mbps 220.63 Mbps
256QAM 60.30 Mbps 185.37 Mbps 251.09 Mbps

2-314 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 7-L. Radio profiles: MPT-HC, static modulation (cont.)

CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME
5 MHz 10 MHz 30 MHz 40 MHZ 50 MHz
15 GHz 4QAM 43.85 Mbps 59.48 Mbps 74.59 Mbps
64QAM 44.73 Mbps 138.02 Mbps 186.978 Mbps 234.22 Mbps
128QAM 52.69 Mbps 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 60.30 Mbps 185.37 Mbps 251.09 Mbps 314.46 Mbps
18 GHz 4QAM 14.02 Mbps 43.85 Mbps 59.48 Mbps 74.59 Mbps
8PSK 21.13 Mbps 65.50 Mbps 88.81 Mbps 111.29 Mbps
16QAM 28.27 Mbps 87.45 Mbps 118.51 Mbps 148.49 Mbps
32QAM 35.23 Mbps 108.75 Mbps 147.36 Mbps 184.60 Mbps
64QAM 44.74 Mbps 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 52.70 Mbps 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 60.31 Mbps 185.37 Mbps 251.09 Mbps 314.46 Mbps
23 GHz 64QAM 44.73 Mbps 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 52.69 Mbps 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 60.30 Mbps 185.37 Mbps 251.09 Mbps 314.46 Mbps
38 GHz 4QAM 43.85 Mbps 59.48 Mbps 74.59 Mbps
16QAM 87.45 Mbps
32QAM 108.75 Mbps
64QAM 44.73 Mbps 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 52.69 Mbps 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 60.30 Mbps 185.37 Mbps 251.09 Mbps 314.46 Mbps

Table 7-M. Radio profiles: MPT-HC, high gain static modulation

CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 40 MHz 50 MHZ
11 GHz 256QAM 220 Mbps
15 GHz 256QAM 220 Mbps
18 GHz 256QAM 220 Mbps 276 Mbps
23 GHz 256QAM 220 Mbps 276 Mbps
38 GHz 256QAM 220 Mbps 276 Mbps

9500 MPR-A general system description 2-315

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY

Table 7-N. Radio profiles: MPT-HC, XPIC, static modulation

CHANNEL MODULATION BANDWIDTH /
FREQUENCY SCHEME DATA PAYLOAD
CAPACITY
30 MHz 40 MHz 50 MHz
Lower 6 GHz 128QAM 162.88 Mbps
256QAM 185.37 Mbps
Upper 6 GHz 128QAM 162.88 Mbps
256QAM 185.37 Mbps
7/8 GHz 128QAM 162.88 Mbps
256QAM 185.37 Mbps
11 GHz 128QAM 162.88 Mbps 220.63 Mbps
256QAM 185.37 Mbps 251.09 Mbps
15 GHz 128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.10 Mbps 314.46 Mbps
18 GHz 128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.09 Mbps 314.46 Mbps
23 GHz 128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.09 Mbps 314.46 Mbps
38 GHz 128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.09 Mbps 314.46 Mbps

Table 7-O. Radio profiles: MPT-HC, high gain, XPIC, static modulation
CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 40 MHz 50 MHZ
11 GHz 256QAM 220 Mbps
15 GHz 256QAM 220 Mbps
18 GHz 256QAM 220 Mbps 276 Mbps
23 GHz 256QAM 220 Mbps 276 Mbps
38 GHz 256QAM 220 Mbps 276 Mbps

2-316 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 7-P. Radio profiles: MPT-HC, adaptive modulation

CHANNEL MODULATION BANDWIDTH / DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 5 MHz 10 MHz 30 MHz 40 MHz 50 MHz
Unlicensed 4 QAM 6.33 Mbps 14.02 Mbps 43.85 Mbps
8PSK 9.69 Mbps 21.13 Mbps 66.50 Mbps
16 QAM 13.03 Mbps 28.27 Mbps 87.45 Mbps
32 QAM 16.13 Mbps 35.23 Mbps 108.75 Mbps
64 QAM 20.58 Mbps 44.73 Mbps 138.02 Mbps
128 QAM 24.36 Mbps 52.69 Mbps 162.88 Mbps
256 QAM 60.30 Mbps 185.37 Mbps
Lower 6 GHz 4QAM1 43.85 Mbps

16QAM1 87.45 Mbps

32QAM1 108.75 Mbps

64QAM 138.02 Mbps
128QAM 162.88 Mbps
256QAM 185.37 Mbps
Upper 6 GHz 4QAM1 14.02 Mbps 43.85 Mbps

8PSK1 21.13 Mbps 66.50 Mbps

16QAM1 28.27 Mbps 87.45 Mbps

32QAM1 35.23 Mbps 108.75 Mbps

64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
7/8 GHz 4QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16QAM 28.27 Mbps 87.45 Mbps
32QAM 35.23 Mbps 108.75 Mbps
64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
11 GHz 4QAM1 43.85 Mbps 59.48 Mbps 74.59 Mbps
64QAM 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.09 Mbps 314.46 Mbps

9500 MPR-A general system description 2-317

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY
Table 7-P. Radio profiles: MPT-HC, adaptive modulation (cont.)
CHANNEL MODULATION BANDWIDTH / DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 5 MHz 10 MHz 30 MHz 40 MHz 50 MHz
15 GHz 4QAM 43.85 Mbps 59.48 Mbps 74.59 Mbps
64QAM 44.73 Mbps 138.02 Mbps 186.98 Mbps 234.23 Mbps
128QAM 52.69 Mbps 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 60.30 Mbps 185.37 Mbps 251.09 Mbps 314.46 Mbps
18 GHz 4QAM 14.02 Mbps 43.85 Mbps 59.48 Mbps 74.59 Mbps
8PSK 21.13 Mbps 65.50 Mbps 88.81 Mbps 111.29 Mbps
16QAM 28.27 Mbps 87.45 Mbps 118.51 Mbps 148.49 Mbps
32QAM 35.23 Mbps 108.75 Mbps 147.36 Mbps 184.60 Mbps
64QAM 44.73 Mbps 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 52.69 Mbps 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 60.30 Mbps 185.37 Mbps 251.09 Mbps 314.46 Mbps
23 GHz 4QAM 43.85 Mbps 59.48 Mbps 74.59 Mbps
64QAM 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.09 Mbps 314.46 Mbps
38 GHz 4QAM 43.85 Mbps 59.48 Mbps 74.59 Mbps
16QAM 87.45 Mbps
32QAM 108.75 Mbps
64QAM 138.02 Mbps 186.97 Mbps 234.22 Mbps
128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.09 Mbps 314.46 Mbps
[1] Subject to FCC Part 101 Rules.

Table 7-Q. Radio profiles: MPT-HC, XPIC, adaptive modulation

CHANNEL MODULATION BANDWIDTH / DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 30 MHz 40 MHz 50 MHz
Upper 6 GHz 64QAM 138.02 Mbps
128QAM 162.88 Mbps
256QAM 185.37 Mbps
7/8 GHz 64QAM 138.02 Mbps
128QAM 162.88 Mbps
256QAM 185.37 Mbps

2-318 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 7-Q. Radio profiles: MPT-HC, XPIC, adaptive modulation (cont.)

CHANNEL MODULATION BANDWIDTH / DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 30 MHz 40 MHz 50 MHz
15 GHz 64QAM 138.02 Mbps 186.98 Mbps 234.23 Mbps
128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.10 Mbps 314.46 Mbps
18 GHz 64QAM 138.02 Mbps 186.98 Mbps 234.23 Mbps
128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.10 Mbps 314.46 Mbps
23 GHz 64QAM 138.02 Mbps 186.98 Mbps 234.23 Mbps
128QAM 162.88 Mbps 220.63 Mbps 276.37 Mbps
256QAM 185.37 Mbps 251.10 Mbps 314.46 Mbps

Table 7-R. Radio profiles: MPT-XP, static modulation

CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME
5 MHz 10 MHz 30 MHz 40 MHZ 50 MHz
Lower 6 GHz 4QAM 43.85 Mbps
16QAM 87.45 Mbps
32QAM 108.75. Mbps
64QAM 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
Upper 6 GHz 4QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16QAM 28.27 Mbps 87.45 Mbps
32QAM 35.23 Mbps 108.75. Mbps
64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
7/8 GHz 4QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16QAM 28.27 Mbps 87.45 Mbps
32QAM 35.23 Mbps 108.75 Mbps
64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps

9500 MPR-A general system description 2-319

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY

Table 7-S. Radio profiles: MPT-XP, XPIC, static modulation

CHANNEL MODULATION BANDWIDTH /
FREQUENCY SCHEME DATA PAYLOAD
CAPACITY
30 MHz 40 MHz 50 MHz
Lower 6 GHz 128QAM 162.88 Mbps
256QAM 185.37 Mbps
Upper 6 GHz 128QAM 162.88 Mbps
256QAM 185.37 Mbps
7/8 GHz 128QAM 162.88 Mbps
256QAM 185.37 Mbps

Table 7-T. Radio profiles: MPT-XP, adaptive modulation

CHANNEL MODULATION BANDWIDTH / DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 5 MHz 10 MHz 30 MHz 40 MHz 50 MHz
Lower 6 GHz 4QAM1 43.85 Mbps

16QAM1 87.45 Mbps

32QAM1 108.75 Mbps

64QAM 138.02 Mbps
128QAM 162.88 Mbps
256QAM 185.37 Mbps
Upper 6 GHz 4QAM1 14.02 Mbps 43.85 Mbps

8PSK1 21.13 Mbps 66.50 Mbps

16QAM1 28.27 Mbps 87.45 Mbps

32QAM1 35.23 Mbps 108.75 Mbps

64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
7/8 GHz 4QAM 14.02 Mbps 43.85 Mbps
8PSK 21.13 Mbps 66.50 Mbps
16QAM 28.27 Mbps 87.45 Mbps
32QAM 35.23 Mbps 108.75 Mbps
64QAM 44.73 Mbps 138.02 Mbps
128QAM 52.69 Mbps 162.88 Mbps
256QAM 60.30 Mbps 185.37 Mbps
[1] Subject to FCC Part 101 Rules.

2-320 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 7-U. Radio profiles: MPT-XP, XPIC, adaptive modulation

CHANNEL MODULATION BANDWIDTH / DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 30 MHz 40 MHz 50 MHz
Upper 6 GHz 64QAM 138.02 Mbps
128QAM 162.88 Mbps
256QAM 185.37 Mbps
7/8 GHz 64QAM 138.02 Mbps
128QAM 162.88 Mbps
256QAM 185.37 Mbps

Table 7-V. Radio profiles: MPT-HL, static modulation

CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 5 MHz 10 MHz 30 MHZ 40 MHZ
Unlicensed 4 QAM 114.2 Mbps
16 QAM 114.2 Mbps
32 QAM 37.3 Mbps 114.2 Mbps
64 QAM
128 QAM 25.8 Mbps 52.6 Mbps 160.2 Mbps
256 QAM 183.3 Mbps

Lower 6 GHz 32 QAM 52.6 Mbps 160.2 Mbps

128 QAM 25.8 Mbps 52.6 Mbps 160.2 Mbps
256 QAM 183.3 Mbps
Upper 6 GHz 128 QAM 25.8 Mbps 52.6 Mbps 160.2 Mbps
256 QAM 183.3 Mbps
7/8 GHz 32 QAM 37.3 Mbps 114.2 Mbps
128 QAM 25.8 Mbps 52.6 Mbps 160.2 Mbps
256 QAM 183.3 Mbps
10.5 GHz 128 QAM 25.8 Mbps
11 GHz 32 QAM 37.3 Mbps 114.2 Mbps
128 QAM 25.8 Mbps 52.6 Mbps 160.2 Mbps 213.9 Mbps
256 QAM 183.3 Mbps 245.2 Mbps

9500 MPR-A general system description 2-321

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY

Table 7-W. Radio profiles: MPT-HL, high gain, static modulation

CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 30 MHZ
Lower 6 GHz 128 QAM 131.1 Mbps
256 QAM 160.2 Mbps
Upper 6 GHz 128 QAM 131.1 Mbps
256 QAM 160.2 Mbps
7/8 GHz 128 QAM 131.1 Mbps
256 QAM 160.2 Mbps
11 GHz 128 QAM 131.1 Mbps
256 QAM 160.2 Mbps

Table 7-X. Radio profiles: MPT-HL, adaptive modulation Note from writer: the SIT metrics
sheet shows only L6 profiles supported. Figures in bold are from the SRS.Should the
other profiles be removed?
CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 30 MHZ
Unlicensed 4 QAM 44.9 Mbps
16 QAM 90.9 Mbps
64 QAM 136.9 Mbps
128 QAM 159.9 Mbps
256 QAM 182.9 Mbps
Lower 6 GHz 4 QAM 44.4 Mbps
16 QAM 89.9 Mbps
64 QAM 135.4 Mbps
128 QAM 158.1Mbps
256 QAM 180.9 Mbps
Upper 6 GHz 4 QAM 44.9 Mbps
16 QAM 90.9 Mbps
64 QAM 136.9 Mbps
128 QAM 159.9 Mbps
256 QAM 182.9 Mbps
7/8 GHz 4 QAM 44.9 Mbps
16 QAM 90.9 Mbps
64 QAM 136.9 Mbps
128 QAM 159.9 Mbps
256 QAM 182.9 Mbps

2-322 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 7-X. Radio profiles: MPT-HL, adaptive modulation (cont.)Note from writer: the SIT
metrics sheet shows only L6 profiles supported. Figures in bold are from the SRS.Should
the other profiles be removed?
CHANNEL MODULATION BANDWIDTH / MAXIMUM DATA PAYLOAD CAPACITY
FREQUENCY SCHEME 30 MHZ
10.5 GHz 4 QAM 44.9 Mbps
16 QAM 90.9 Mbps
64 QAM 136.9 Mbps
128 QAM 159.9 Mbps
256 QAM 182.9 Mbps
11 GHz 4 QAM 44.9 Mbps
16 QAM 90.9 Mbps
64 QAM 136.9 Mbps
128 QAM 159.9 Mbps
256 QAM 182.9 Mbps

DS1 interface

Table 7-Y. DS1 interface specifications

ITEM CHARACTERISTICS
1. Location DS1 connectors on P32E1DS1 card equipped in MSS-8 shelf
2. Function Couples DS1s into and out of P32E1DS1 card equipped in MSS-8 shelf
3. Capacity 32 unprotected DS1s per P32E1DS1 card
32 protected DS1s per pair of P32E1DS1 cards
4. Frequency 1.544 Mb/s ±32 pulse position modulation (ppm)
5. Line code AMI (bipolar) with B8ZS coding

9500 MPR-A general system description 2-323

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY
Table 7-Y. DS1 interface specifications (cont.)
ITEM CHARACTERISTICS
6. Line impedance 100 ohms ±5%, balanced
7. Level Measured with all 1's signal in 3 kHz bandwidth centered
at 772 kHz into100 ohms ±5%
Input @ 772 kHz +12.6 to +17.9 dBm at equal-level point plus attenuation of 0 to 655 ft of
cable
Output @ 772 kHz +12.6 to +17.9 dBm at equal-level point after attenuation of 0 to 655 ft of
cable
Output @ 1.544 MHz More than 29 dB below level at 772 kHz
8. Pulse shape:
Output Complies with GR-499-CORE. Meets DS1 format template requirements
(see figure 7-1).
9. Cable type Twisted-pair cable, typical 22 AWG ABAM. Complies with ANSI
T1.102-1993
Maximum cable length 660 ft from defined DSX-level point

2-324 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 7-1. DS1 format template

1.5

1.0
NORMALIZED AMPLITUDE

0.5

–0.5

–1.0
–1.0 –0.5 0.0 0.5 1.0 1.5

TIME, IN UNIT INTERVALS

MAXIMUM CURVE
TIME –0.77 –0.39 –0.27 –0.27 –0.12 0.00 0.27 0.35 0.93 1.16
UNIT INTERVALS

NORMALIZED 0.05 0.05 0.80 1.15 1.15 1.05 1.05 –0.07 0.05 0.05
AMPLITUDE

MINIMUM CURVE
TIME –0.77 –0.23 –0.23 –0.15 0.00 0.15 0.23 0.23 0.46 0.66 0.93 1.16
UNIT INTERVALS

NORMALIZED –0.05 –0.05 0.50 0.95 0.95 0.90 0.50 –0.45 –0.45 –0.20 –0.05 –0.05
AMPLITUDE

DG129–0226–1
041698

9500 MPR-A general system description 2-325

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY

Figure 7-2. DS1 input jitter accommodation

5 UI
(PEAK-TO-PEAK)
INPUT JITTER

ACCEPTABLE
DS1

RANGE

0.1 UI

10 Hz 500 Hz 8 kHz 40 kHz

FREQUENCY

950-0208-1
071510

Figure 7-3. DS1 jitter transfer characteristics

40 dB/DECADE

0.1 dB
TRANSFER FUNCTION
RECEIVER JITTER

20 dB/DECADE

ACCEPTABLE
DS1

RANGE

10 Hz 350 Hz 2.5 kHz 15 kHz

FREQUENCY 950-0209-1
071510

2-326 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 7-4. DS1 jitter measurement filter characteristics

40 dB/DECADE

0.1 dB
TRANSFER FUNCTION

20 dB/DECADE
RECEIVER JITTER

ACCEPTABLE
DS1

RANGE

10 Hz 350 Hz 2.5 kHz 15 kHz

FREQUENCY 950-0209-1
071510

DS3 interface

Table 7-Z. DS3 interface specifications

ITEM CHARACTERISTICS
1. Location Mini-BNC connectors on the P2E3DS3 card equipped in the MSS-8 shelf
2. Function Couples DS3s into and out of P2E3DS3 card
3. Capacity 1 to 2 full-duplex DS3 ports per P2E3DS3 card
4. Frequency 44.736 Mb/s ±20 ppm
5. Line code AMI (bipolar) with B3ZS coding
6. Format Asynchronous framed DS3 per ANSI T1.107-1997 standard. See
figure 7-5.
DS3 C-bit parity with C-bit mode operation per ANSI Standard T1.107a
(R5.0)
7. Line impedance 75 ohms +5%, unbalanced
8. Level Measured with all 1's signal and 3 kHz bandwidth into 75 ohms +5%
Input @ 22 MHz -1.8 to +5.7 dBm at equal-level point less attenuation of 0 to 450 ft of cable
Output @ 44 MHz More than 20 dB below level @ 22 MHz
9. Pulse shape:
Output Compliant with GR-499-CORE. Meets DS3 format template requirements
(see figure 7-5).
10. Cable type 75 ohm BNC coaxial cables, 728A
11. Mating connector type Mini-BNC male

9500 MPR-A general system description 2-327

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY
Table 7-Z. DS3 interface specifications (cont.)
ITEM CHARACTERISTICS
12. Jitter All measurements are made on a half-duplex cross-connection.
Input accommodation See figure 7-6.
Output transfer See figure 7-7.
Generation 0.5 unit interval (UI) p-p nominal
0.7 unit interval (UI) p-p maximum
Filter used to measure jitter must have shape shown in figure 7-8.

2-328 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 7-5. Asynchronous DS3 format template

1.2

1.0

0.8
NORMALIZED AMPLITUDE

0.6

0.4

0.2

0.0

-0.2

-0.4
-1.0 -1.5 0.0 0.5 1.0 1.5

TIME (UNIT INTERVALS)

INVERTED PULSE SHOWN TO AID OSCILLOSCOPE TIME-BASE ADJUSTMENT

TIME NORMALIZED
CURVE UNIT INTERVALS AMPLITUDE

MAXIMUM
CURVE

MINIMUM
CURVE

671-0498-1
071504

9500 MPR-A general system description 2-329

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY

Figure 7-6. DS3 input jitter accommodation

5 UI
(PEAK-TO-PEAK)
INPUT JITTER

ACCEPTABLE
DS3

RANGE

0.1 UI

10 Hz 2.3 kHz 60 kHz 300 kHz

FREQUENCY
671-0499-1
071504

Figure 7-7. DS3 jitter transfer characteristics

0.1 dB 20 dB/DECADE
TRANSFER FUNCTION
RECEIVER JITTER
DS3

ACCEPTABLE
RANGE

10 Hz 1000 Hz 15 kHz

FREQUENCY 671-0500-1
071504

2-330 9500 MPR-A general system description

 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 7-8. DS3 jitter measurement filter characteristics

TRANSFER FUNCTION 0.1 dB 20 dB/DECADE

RECEIVER JITTER
DS3

ACCEPTABLE
RANGE

10 Hz 1000 Hz 15 kHz

FREQUENCY 671-0500-1
071504

9500 MPR-A general system description 2-331

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY

Figure 7-9. Combined STS-1 and DS3 Format Template

NORMALIZED DS3 & STS MASK/EYE COMBINED

C D
1.00

I J
B
0.75

0.50

A E

0.25 H K 1 UNIT INTERVAL

G F

0.00

-1.00 0 1.00

DS3 MASK STS EYE DIAGRAM

UPPER CURVE AMPLITUDE OUTER REGION CORNER INNER REGION CORNER
POINTS TIME AMPLITUDE POINTS TIME AMPLITUDE
A -0.50 0.37 F 0.28 0.12
B -0.44 0.80 G 0.00 0.16
C -0.15 1.00 H -0.25 0.24
I -0.04 0.80
D 0.08 1.00 J 0.04 0.80
E 0.50 0.37 K 0.11 0.22
LOWER CURVE STS-1 MASK
UPPER CURVE AMPLITUDE

LOWER CURVE

671-0502-1
071504

2-332 9500 MPR-A general system description

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Unit Data Sheets (UDSs)

UDS-100
9500 MPR-A unit data sheet cross-reference
Unit Data Sheet Cross-Reference by UDS Number

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-100 9500 MPR-A unit data sheet cross-reference N/A N/A N/A
UDS-101 MSS-8 Microwave Service Switch Shelf N/A Inactive 3DB18485AA
MSS-8 Microwave Service Switch Shelf CRMLB10HRA Active 3DB18485AB
UDS-102 MPT-HL Microwave Packet transport-Long N/A Active 3EM22618AB
Haul Shelf
UDS-103 CSM-E Enhanced Control and Switching CRCCAEVEAA Active 3DB18326AC
Module
UDS-104 MOD300 Radio Interface N/A Inactive 3DB18136AC
MOD300 Radio Interface N/A Inactive 3DB18136AD
MOD300 Radio Interface CRG2ABVDAA Active 3DB18136AE
MOD300EN Radio Interface CRG2ABWDAA Active 3DB18538AC
UDS-105 P32E1DS1 DS1 PDH Card N/A Inactive 3DB18126AD
P32E1DS1 DS1 PDH Card CRG2ABUDAA Active 3DB18126AE
UDS-106 P2E3DS3 DS3 PDH Card N/A Inactive 3DB18194AB
P2E3DS3 DS3 PDH Card CRG2AA9DAA Active 3DB18194AC
UDS-107 P8ETH Ethernet Access Switch Card CRCCACGJAA Active 3DB18206AC
UDS-108 ODU300, L6 GHz, 252.04 MHz SEPARATION
ODU300, 5930 - 6020 MHZ, HP, TX LOW N/A Inactive 3DB23215AA
ODU300, 5989 - 6079 MHZ, HP, TX LOW N/A Inactive 3DB23215AB
ODU300, 6078 - 6168 MHZ, HP, TX LOW N/A Inactive 3DB23215AC
ODU300, 6182 - 6272 MHZ, HP, TX HIGH N/A Inactive 3DB23215AD
ODU300, 6241 - 6331 MHZ, HP, TX HIGH N/A Inactive 3DB23215AE
ODU300, 6330 - 6420 MHZ HP, TX HIGH N/A Inactive 3DB23215AF
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR, L6 GHz, 252.04 MHz SEPARATION
ODU300, 5930 - 6020 MHZ, HP, TX LOW CRMLT10HRB Active 3DB23215HA
ODU300, 5989 - 6079 MHZ, HP, TX LOW CRMLV10HRB Active 3DB23215HB
ODU300, 6078 - 6168 MHZ, HP, TX LOW CRMLX10HRB Active 3DB23215HC
ODU300, 6182 - 6272 MHZ, HP, TX HIGH CRMLU10HRB Active 3DB23215HD
ODU300, 6241 - 6331 MHZ, HP, TX HIGH CRMLW10HRB Active 3DB23215HE
ODU300, 6330 - 6420 MHZ HP, TX HIGH CRMLY10HRB Active 3DB23215HF

9500 MPR-A unit data sheet cross-reference 3-1

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-108 ODU300, U6 GHz, 160 MHz SEPARATION
ODU300, 6540 - 6610 MHZ, HP, TX LOW N/A Inactive 3DB23214AA
ODU300, 6710 - 6780 MHZ, HP, TX HIGH N/A Inactive 3DB23214AB
ODU300, 6590 - 6660 MHZ, HP, TX LOW N/A Inactive 3DB23214AC
ODU300, 6760 - 6830 MHZ, HP, TX HIGH N/A Inactive 3DB23214AD
ODU300, 6640 - 6710 MHZ, HP, TX LOW N/A Inactive 3DB23214AE
ODU300, 6800 - 6870 MHZ, HP, TX HIGH N/A Inactive 3DB23214AF
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR, U6 GHz, 160 MHz SEPARATION
ODU300, 6540 - 6610 MHZ, HP, TX LOW CRMLZ10HRB Active 3DB23214HA
ODU300, 6710 - 6780 MHZ, HP, TX HIGH CRML110HRB Active 3DB23214HB
ODU300, 6590 - 6660 MHZ, HP, TX LOW CRML210HRB Active 3DB23214HC
ODU300, 6760 - 6830 MHZ, HP, TX HIGH CRML310HRB Active 3DB21214HD
ODU300, 6640 - 6710 MHZ, HP, TX LOW CRML410HRB Active 3DB23214HE
ODU300, 6800 - 6870 MHZ, HP, TX HIGH CRML510HRB Active 3DB23214HF
UDS-108 ODU300, U6 GHz, 340 MHz SEPARATION
ODU300, 6430 - 6590 MHz, HP TX LOW N/A Inactive 3DB23216AA
ODU300, 6770 - 6930 MHz, HP TX HIGH N/A Inactive 3DB23216AB
ODU300, 6515 - 6675 MHz, HP TX LOW N/A Inactive 3DB23216AC
ODU300, 6855 - 7015 MHz, HP TX HIGH N/A Inactive 3DB23216AD
ODU300, 6600 - 6760 MHz, HP TX LOW N/A Inactive 3DB23216AE
ODU300, 6940 - 7100 MHz, HP TX HIGH N/A Inactive 3DB23216AF
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR, U6 GHz, 340 MHz SEPARATION
ODU300, 6430 - 6590 MHz, HP TX LOW CRML610HRB Active 3DB23216HA
ODU300, 6770 - 6930 MHz, HP TX HIGH CRML710HRB Active 3DB23216HB
ODU300, 6515 - 6675 MHz, HP TX LOW CRML810HRB Active 3DB23216HC
ODU300, 6855 - 7015 MHz, HP TX HIGH CRML910HRB Active 3DB23216HD
ODU300, 6600 - 6760 MHz, HP TX LOW CRMMA00ARB Active 3DB23216HE
ODU300, 6940 - 7100 MHz, HP TX HIGH CRMMB00ARB Active 3DB23216HF
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR, 7 GHz, 175 MHz SEPARATION
ODU300, 7124 - 7185 MHz, HP, TX Low N/A Active 3DB23223HA
ODU300, 7299 - 7360 MHz, HP, TX High N/A Active 3DB23224HA
ODU300, 7157.5 - 7217.5 MHz, HP, TX Low N/A Active 3DB23225HA
ODU300, 7332.5 - 7392.5 MHz, HP, TX High N/A Active 3DB23226HA
ODU300, 7190 - 7250 MHz, HP, TX Low N/A Active 3DB23227HA
ODU300, 7365 - 7425 MHz, HP, TX High N/A Active 3DB23228HA

3-2 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR, 7 GHz, 150 MHz SEPARATION
ODU300, 7424 - 7485 MHz, HP, TX Low N/A Active 3DB23217HA
ODU300, 7574 - 7635 MHz, HP, TX High N/A Active 3DB23218HA
ODU300, 7470 - 7530 MHz, HP, TX Low N/A Active 3DB23219HA
ODU300, 7620 - 7680 MHz, HP, TX High N/A Active 3DB23220HA
ODU300, 7515 - 7575 MHz, HP, TX Low N/A Active 3DB23221HA
ODU300, 7665 - 7725 MHz, HP, TX High N/A Active 3DB23222HA
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR, 8 GHz, 300 MHz SEPARATION
ODU300, 7722.5 - 7859 MHz, HP, TX Low N/A Active 3DB23033HA
ODU300, 8025 - 8171 MHz, HP, TX High N/A Active 3DB23033HC
ODU300, 7844 - 7981 MHz, HP, TX Low N/A Active 3DB23033HB
ODU300, 8145 - 8287 MHz, HP, TX High N/A Active 3DB23033HD
UDS-108 ODU300 11 GHz, 590-490 MHz SEPARATION
ODU300, 10675 - 10835 MHZ, TX LOW N/A Inactive 3DB23035AA
ODU300, 10795 - 10955 MHZ, TX LOW N/A Inactive 3DB23035AB
ODU300, 10915 - 11075 MHZ, TX LOW N/A Inactive 3DB23035AC
ODU300, 11035 - 11200 MHZ, TX LOW N/A Inactive 3DB23035AD
ODU300, 11200 - 11345 MHZ, TX HIGH N/A Inactive 3DB23035AE
ODU300, 11310 - 11465 MHZ, TX HIGH N/A Inactive 3DB23035AF
ODU300, 11430 - 11585 MHZ, TX HIGH N/A Inactive 3DB23035AG
ODU300, 11550 - 11705 MHZ, TX HIGH N/A Inactive 3DB23035AH
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 11 GHz, 590-490 MHz SEPARATION
ODU300, 10675 - 10835 MHZ, TX LOW CRMMC00ARB Active 3DB23035HA
ODU300, 10795 - 10955 MHZ, TX LOW CRMME00ARB Active 3DB23035HB
ODU300, 10915 - 11075 MHZ, TX LOW CRMMG00ARB Active 3DB23035HC
ODU300, 11035 - 11200 MHZ, TX LOW CRMMJ00ARB Active 3DB23035HD
ODU300, 11200 - 11345 MHZ, TX HIGH CRMMD00ARB Active 3DB23035HE
ODU300, 11310 - 11465 MHZ, TX HIGH CRMMF00ARB Active 3DB23035HF
ODU300, 11430 - 11585 MHZ, TX HIGH CRMMH00ARB Active 3DB23035HG
ODU300, 11550 - 11705 MHZ, TX HIGH CRMMK00ARB Active 3DB23035HH
UDS-108 ODU300 15 GHz, 475/490 MHz SEPARATION
ODU300, 14500 - 14660 MHZ, TX LOW N/A Inactive 3DB23039AC
ODU300, 14975 - 15135 MHZ, TX HIGH N/A Inactive 3DB23039AD

9500 MPR-A unit data sheet cross-reference 3-3

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 15 GHz, 475/490 MHz SEPARATION
ODU300, 14500 - 14660 MHZ, TX LOW N/A Active 3DB23039HC
ODU300, 14975 - 15135 MHZ, TX HIGH N/A Active 3DB23039HD
UDS-108 ODU300 18 GHz, 340 MHz SEPARATION
ODU300, 18580 - 18660 MHZ, TX LOW N/A Inactive 3DB23041AA
ODU300, 18660 - 18740 MHZ, TX LOW N/A Active 3DB23041AB
ODU300, 18740 - 18820 MHZ, TX LOW N/A Inactive 3DB23041AC
ODU300, 18920 - 19000 MHZ, TX HIGH N/A Active 3DB23041AD
ODU300, 19000 - 19080 MHZ, TX HIGH N/A Inactive 3DB23041AE
ODU300, 19080 - 19160 MHZ, TX HIGH N/A Active 3DB23041AF
UDS-108 ODU300 18 GHz, 1008/1010/1092/1120 MHz SEPARATION
ODU300, 17700 - 18060 MHZ, TX LOW N/A Active 3DB23042AA
ODU300, 17905 - 18275 MHZ, TX LOW N/A Active 3DB23042AB
ODU300, 18110 - 18490 MHZ, TX LOW N/A Inactive 3DB23042AC
ODU300, 18330 - 18690 MHZ, TX LOW N/A Inactive 3DB23042AD
ODU300, 18710 - 19070 MHZ, TX HIGH N/A Active 3DB23042AE
ODU300, 18920 - 19290 MHZ, TX HIGH N/A Inactive 3DB23042AF
ODU300, 19130-19510 MHZ, TX HIGH N/A Active 3DB23042AG
ODU300, 19340 - 19700 MHZ, TX HIGH N/A Inactive 3DB23042AH
UDS-108 ODU300 18 GHz, 1560 MHz SEPARATION
ODU300, 17700 - 18060 MHZ, TX LOW N/A Inactive 3DB23062AC
ODU300, 19260 - 19620 MHZ, TX HIGH N/A Inactive 3DB23062AD
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 18 GHz, 1560 MHz SEPARATION
ODU300, 17700 - 18060 MHZ, TX LOW CRMML00ARB Active 3DB23062HC
ODU300, 19260 - 19620 MHZ, TX HIGH CRMMM00ARB Active 3DB23062HD
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 18 GHz, 1560 MHz SEPARATION, HIGH
POWER
ODU300, 17700 - 18140 MHZ, TX LOW, HP N/A Active 3DB23062HE
ODU300, 19260 - 19700 MHZ, TX HIGH, HP N/A Active 3DB23062HF

3-4 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-108 ODU300 23 GHz, 1200 MHz SEPARATION
ODU300, 21200 - 21570 MHZ, TX LOW N/A Inactive 3DB23045AA
ODU300, 21475 - 21845 MHZ, TX LOW N/A Inactive 3DB23045AB
ODU300, 21750 - 22120 MHZ, TX LOW N/A Inactive 3DB23045AC
ODU300, 22030 - 22400 MHZ, TX LOW N/A Inactive 3DB23045AD
ODU300, 22400 - 22770 MHZ, TX HIGH N/A Inactive 3DB23045AE
ODU300, 22675 - 23045 MHZ, TX HIGH N/A Inactive 3DB23045AF
ODU300, 22950 - 23320 MHZ, TX HIGH N/A Inactive 3DB23045AG
ODU300, 23230 - 23600 MHZ, TX HIGH N/A Inactive 3DB23045AH
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 23 GHz, 1200 MHz SEPARATION
ODU300, 21200 - 21570 MHZ, TX LOW CRMMN00ARB Active 3DB23045HA
ODU300, 21475 - 21845 MHZ, TX LOW CRMMR00ARB Active 3DB23045HB
ODU300, 21750 - 22120 MHZ, TX LOW CRMMT00ARB Active 3DB23045HC
ODU300, 22030 - 22400 MHZ, TX LOW CRMMV00ARB Active 3DB23045HD
ODU300, 22400 - 22770 MHZ, TX HIGH CRMMP00ARB Active 3DB23045HE
ODU300, 22675 - 23045 MHZ, TX HIGH CRMMS00ARB Active 3DB23045HF
ODU300, 22950 - 23320 MHZ, TX HIGH CRMMU00ARB Active 3DB23045HG
ODU300, 23230 - 23600 MHZ, TX HIGH CRMMW00ARB Active 3DB23045HH
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 23 GHz, 1200 MHz SEPARATION, HIGH
POWER
ODU300, 21200 - 21570 MHZ, TX LOW, HP N/A Active 3DB23045HI
ODU300, 21475 - 21845 MHZ, TX LOW, HP N/A Active 3DB23045HJ
ODU300, 21750 - 22120 MHZ, TX LOW, HP N/A Active 3DB23045HK
ODU300, 22030 - 22400 MHZ, TX LOW, HP N/A Active 3DB23045HL
ODU300, 22400 - 22770 MHZ, TX HIGH, HP N/A Active 3DB23045HM
ODU300, 22675 - 23045 MHZ, TX HIGH, HP N/A Active 3DB23045HN
ODU300, 22950 - 23320 MHZ, TX HIGH, HP N/A Active 3DB23258HO
ODU300, 23230 - 23600 MHZ, TX HIGH, HP N/A Active 3DB23045HP

9500 MPR-A unit data sheet cross-reference 3-5

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-108 ODU300 W/LIGHTNING SURGE SUPPRESSOR 38 GHz, 700 MHz SEPARATION
ODU300, 38600 - 38800 MHZ, TX LOW N/A Active 3DB23258HO
ODU300, 39300 - 39500 MHZ, TX HIGH N/A Active 3DB23258HP
ODU300, 38750 - 38950 MHZ, TX LOW N/A Active 3DB23258HQ
ODU300, 39450 - 39650 MHZ, TX HIGH N/A Active 3DB23258HR
ODU300, 38950 - 39150 MHZ, TX LOW N/A Active 3DB23258HS
ODU300, 39650 - 39850 MHZ, TX HIGH N/A Active 3DB23258HT
ODU300, 39100 - 39300 MHZ, TX LOW N/A Active 3DB23258HU
ODU300, 39800 - 40000 MHZ, TX HIGH N/A Active 3DB23258HV
UDS-109 MPT-HL Transceivers 6/11 GHz
MPT-HL Transceiver L6, 5725-6425 MHz CRTUAAXFAA Active 3EM22617AA
MPT-HL Transceiver U6, 6425-6930 MHz CRTUAAYFAA Active 3EM22617AB
MPT-HL Transceiver L6, 5925-6425 MHz, CRTUABLFAA Active 3EM22617AC
HP
MPT-HL Transceiver U6, 6425-6930 MHz, CRTUABMFAA Active 3EM22617AD
HP
MPT-HL Transceiver 7, 7125-7775 MHz N/A Active 3EM24627AA
MPT-HL Transceiver 8, 7725-8500 MHz N/A Active 3EM24627AB
MPT-HL Transceiver 10.5, 10400-10700 CRTUABPCAA Active 3EM23888AA
MHz
MPT-HL Transceiver 11, 10700-11200 MHz CRTUABRCAA Active 3EM23888AB
MPT-HL Transceiver 11, 11200-11700 MHz CRTUABSCAA Active 3EM23888AC
UDS-110 Fan 2U Card N/A Active 3DB18134BA
Fan 2U Card CRCCACPJAA Active 3DB18134BB
Fan 2U Card W/Alarms CRCCADYJAA Active 3EM23911AA
Fan 1U Card N/A-4 Active-4 3DB18218AD
UDS-111 GigE SFP 1000Base-SX, 850 nm DRR3AA3CAA Active 3EM20277AA
GigE SFP 1000Base-LX, 1310 nm DRR3AA4CAA Active 3EM20277AB
GigE SFP 1000Base-EX, 1310 nm DRR3AA5CAA Active 3EM20277AC
GigE SFP 1000Base-ZX, 1550 nm DRR3AA6CAA Active 3EM20277AD
UDS-112 PDU Power Distribution Unit N/A Active 3EM13317AA
UDS-114 Type N Adapter Bracket N/A Active 3EM23272AA
UDS-113 DS1 RJ-45 Patch Panel N/A Active 1AF15245AB
UDS-115 DS1 D-Connector Patch Panel N/A Active 3DB16102AA
UDS-116 DS3 Hybrid Splitter N/A Active 3EM22900AA
UDS-116 DS3 Patch Panel N/A Active 3EM24462AA

3-6 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-117 MSS-4 Microwave Service Switch Shelf N/A Active 3DB18219AB
UDS-118 MPTACC MPT Access N/A Active 3DB18634AB
UDS-119 MPT-HC L6 GHz, 252.04 MHz separation with embedded diplexer
MPT-HC, 5929 - 6050 MHZ, TX LOW N/A Active 3DB20441BA
MPT-HC, 6182 - 6302.04 MHZ, TX HIGH N/A Active 3DB20443BA
MPT-HC, 6047.96 - 6168 MHZ, TX LOW N/A Active 3DB20442BA
MPT-HC, 6300 - 6420.04 MHZ, TX HIGH N/A Active 3DB20444BA
UDS-119 MPT-HC U6 GHz, 160 MHz separation with embedded diplexer
MPT-HC, 6540 - 6610 MHZ, TX LOW N/A Active 3DB20367BA
MPT-HC, 6710 - 6780 MHZ, TX HIGH N/A Active 3DB20435BA
MPT-HC, 6590 - 6660 MHZ, TX LOW N/A Active 3DB20434BA
MPT-HC, 6750 - 6820 MHZ, TX HIGH N/A Active 3DB20436BA
MPT-HC, 6640 - 6710 MHZ, TX LOW N/A Active 3DB20462BA
MPT-HC, 6800 - 6870 MHZ, TX HIGH N/A Active 3DB20463BA
UDS-119 MPT-HC U6 GHz, 340 MHz separation with embedded diplexer
MPT-HC, 6420 - 6600 MHZ, TX LOW N/A Active 3DB20437BA
MPT-HC, 6760 - 6940 MHZ, TX HIGH N/A Active 3DB20439BA
MPT-HC, 6565 - 6720 MHZ, TX LOW N/A Active 3DB20438BA
MPT-HC, 6905 - 7060 MHZ, TX HIGH N/A Active 3DB20440BA
MPT-HC, 6595 - 6775 MHZ, TX LOW N/A Active 3DB20464BA
MPT-HC, 6935 - 7115 MHZ, TX HIGH N/A Active 3DB20465BA
UDS-119 MPT-HC 11 GHz, 490/500 MHz separation with embedded diplexer
MPT-HC, 10695 - 10955 MHZ, TX LOW CRMYAB7JRA Inactive 3DB20371BA
MPT-HC, 10695 - 10955 MHZ, TX LOW N/A Active 3DB20371BB
MPT-HC, 11205 - 11485 MHZ, TX HIGH CRMYAB8JRA Inactive 3DB20547BA
MPT-HC, 11205 - 11485 MHZ, TX HIGH N/A Active 3DB20547BB
MPT-HC, 10935 - 11205 MHZ, TX LOW CRMYAB9JRA Inactive 3DB20546BA
MPT-HC, 10935 - 11205 MHZ, TX LOW N/A Active 3DB20546BB
MPT-HC, 11445 - 11705 MHZ, TX HIGH CRMYACAJRA Inactive 3DB20548BA
MPT-HC, 11445 - 11705 MHZ, TX HIGH N/A Active 3DB20548BB
UDS-119 MPT-HC 15 GHz, 475 MHz separation with embedded diplexer
MPT-HC, 14500 - 14724 MHZ, TX LOW N/A Active 3DB20373BA
MPT-HC, 14920 - 15144 MHZ, TX HIGH N/A Active 3DB20423BA

9500 MPR-A unit data sheet cross-reference 3-7

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-119 MPT-HC 18 GHz, 1560 MHz separation with embedded diplexer
MPT-HC, 17700 - 18140 MHZ CRMYAB1JRA Active 3DB20432BA
MPT-HC, 19260 - 19700 MHz CRMYAB2JRA Active 3DB20433BA
UDS-119 MPT-HC 23 GHz, 1200/1232 MHz separation with embedded diplexer
MPT-HC, 21198 - 21819 MHZ, TX LOW CRMYAB3JRA Active 3DB20473BA
MPT-HC, 22400 - 23019 MHZ, TX HIGH CRMYAB4JRA Active 3DB20475BA
MPT-HC, 21781 - 22400 MHZ, TX LOW CRMYAB5JRA Active 3DB20474BA
MPT-HC, 22981 - 23600 MHZ, TX HIGH CRMYAB6JRA Active 3DB20476BA
UDS-119 MPT-HC 38 GHz, 700 MHz separation with embedded diplexer
MPT-HC, 38600 - 38950 MHZ, TX LOW N/A Active 3DB20379BA
MPT-HC, 39300 - 39650 MHZ, TX HIGH N/A Active 3DB20563BA
MPT-HC, 38950 - 39300 MHZ, TX LOW N/A Active 3DB20562BA
MPT-HC, 39650 - 40000 MHZ, TX HIGH N/A Active 3DB20564BA
UDS-119 9558HC 5.8 GHz Unlicensed, 64 MHz separation with external diplexer
9558HC, 5725.5-5785.5 MHz, TX LOW N/A Active 3DB20913BA
9558HC, 5789.5-5849.5 MHz, TX HIGH N/A Active 3DB20914BA
UDS-119 MPT-HC L6 GHz, 252.04 MHz separation with external diplexer
MPT-HC, 5929.96 - 6168 MHZ, TX LOW N/A Active 3DB20800BA
MPT-HC, 6182 - 6420.04 MHZ, TX HIGH N/A Active 3DB20802BA
UDS-119 MPT-HC U6 GHz, 160/340 MHz separation with external diplexer
MPT-HC, 6420 - 6775 MHZ, TX LOW N/A Active 3DB20804BA
MPT-HC, 6710 - 7115 MHZ, TX HIGH N/A Active 3DB20806BA
UDS-119 MPT-HC 7/8 GHz, 175/300 MHz separation with external diplexer
MPT-HC, 7107 - 8377 MHZ, TX LOW N/A Active 3DB20454BC
MPT-HC, 7261 - 8496.114 MHZ, TX HIGH N/A Active 3DB20456BC
UDS-119 MPT-XP L6 GHz, 252.04 MHz separation with external diplexer
MPT-XP, 5929.96 - 6168 MHZ, TX LOW N/A Active 3DB20760BA
MPT-XP, 6182 - 6420.04 MHZ, TX HIGH N/A Active 3DB20761BA
UDS-119 MPT-XP U6 GHz, 160/340 MHz separation with external diplexer
MPT-XP, 6420 - 6775 MHZ, TX LOW N/A Active 3DB20763BA
MPT-XP, 6710 - 7115 MHZ, TX HIGH N/A Active 3DB20764BA
UDS-119 MPT-XP 7 GHz, 175 MHz separation with external diplexer
MPT-XP, 7107 - 7714.5 MHZ, TX LOW N/A Active 3DB20771BA
MPT-XP, 7261 - 7911 MHZ, TX HIGH N/A Active 3DB20772BA

3-8 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS PART
NUMBER DESCRIPTION CLEI STATUS NUMBER
UDS-119 MPT-XP 8 GHz, 300 MHz separation with external diplexer
MPT-XP, 7725 - 8377 MHZ, TX LOW N/A Active 3DB20773BA
MPT-XP, 8025 - 8496.114 MHZ, TX HIGH N/A Active 3DB20774BA
UDS-119 MPT-HC/XP external protection module
RPS Module N/A Active 3DB20117BA
XPIC+RPS Module N/A Inactive 3DB20116BA
XPIC+RPS Module N/A Active 3DB20116BB
UDS-120 AUX Auxiliary Card N/A Active 3DB18236AB
UDS-121 Power Injector Card N/A Active 3CC50128AA
Power Injector Box N/A Active 3CC50129AA
UDS-122 +24/-48 Volt Converter (2 Converters N/A Active 3DB18862AA
W/Chassis)
+24/-48 Volt Converter (1 Converter N/A Active 3DB18863AA
W/Chassis)
+24/-48 Volt Converter (Spare) N/A Active 3DB18764AA
UDS-123 MPT Power Unit N/A Active 3CC50173AA
UDS-125 MPT Extended Power Unit
UDS-125 SDHACC OC-3 SDH Card N/A Active 3DB18735AA

9500 MPR-A unit data sheet cross-reference 3-9

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

Unit Data Sheet Cross-Reference by Part Number

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
1AF15245AB DS1 RJ-45 Patch Panel N/A Active UDS-113
3CC50128AA Power Injector Card N/A Active UDS-121
3CC50129AA Power Injector Box N/A Active
3CC50173AA MPT Power Unit N/A Active UDS-123
3DB16102AA DS1 D-Connector Patch Panel N/A Active UDS-115
3DB18485AA MSS-8 Microwave Service Switch Shelf N/A Inactive UDS-101
3DB18485AB MSS-8 Microwave Service Switch Shelf CRMLB10HRA Active UDS-101
3DB18126AD P32E1DS1 DS1 PDH Card N/A Inactive UDS-105
3DB18126AE P32E1DS1 DS1 PDH Card CRG2ABUDAA Active UDS-105
3DB18134BA Fan 2U Card N/A Active UDS-110
3DB18134BB Fan 2U Card CRCCACPJAA Active UDS-110
3DB18136AC MOD300 Radio Interface N/A Inactive UDS-104
3DB18136AD MOD300 Radio Interface N/A Inactive UDS-104
3DB18136AE MOD300 Radio Interface CRG2ABVDAA Active UDS-104
3DB18194AB P2E3DS3 DS3 PDH Card N/A Inactive UDS-106
3DB18194AC P2E3DS3 DS3 PDH Card CRG2AA9DAA Active UDS-106
3DB18206AC P8ETH Ethernet Access Switch Card CRCCACGJAA Active UDS-107
3DB18209AB CSM-B Control and Switching Module N/A Active UDS-103
3DB18218AD Fan 1U Card N/A-4 Active-4 UDS-110
3DB18219AB MSS-4 Microwave Service Switch Shelf N/A Active UDS-117
3DB18236AB AUX Auxiliary Card N/A Active UDS-120
3DB18326AC CSM-E Enhanced Control and Switching CRCCAEVEAA Active UDS-103
Module
3DB18538AC MOD300EN Radio Interface CRG2ABWDAA Active UDS-104
3DB18634AB MPTACC MPT Access N/A Active UDS-118
3DB18735AA SDHACC OC-3 SDH Card N/A Active UDS-125
3DB18862AA +24/-48 Volt Converter (2 Converters N/A Active UDS-122
W/Chassis)
3DB18863AA +24/-48 Volt Converter (1 Converter N/A Active
W/Chassis)
3DB18764AA +24/-48 Volt Converter (Spare) N/A Active
3DB20116BA XPIC+RPS Module N/A Inactive UDS-119
3DB20116BB XPIC+RPS Module N/A Active UDS-119
3DB20117BA RPS Module N/A Active UDS-119

3-10 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
3DB20367BA MPT-HC, 6540 - 6610 MHZ, TX LOW N/A Active UDS-119
3DB20371BA MPT-HC, 10695 - 10955 MHZ, TX LOW CRMYAB7JRA Inactive UDS-119
3DB20371BB MPT-HC, 10695 - 10955 MHZ, TX LOW N/A Active UDS-119
3DB20373BA MPT-HC, 14500 - 14724 MHZ, TX LOW N/A Active UDS-119
3DB20379BA MPT-HC, 38600 - 38950 MHZ, TX LOW N/A Active UDS-119
3DB20423BA MPT-HC, 14920 - 15144 MHZ, TX HIGH N/A Active UDS-119
3DB20432BA MPT-HC, 17700 - 18140 MHZ CRMYAB1JRA Active UDS-119
3DB20433BA MPT-HC, 19260 - 19700 MHz CRMYAB2JRA Active UDS-119
3DB20434BA MPT-HC, 6590 - 6660 MHZ, TX LOW N/A Active UDS-119
3DB20435BA MPT-HC, 6710 - 6780 MHZ, TX HIGH N/A Active UDS-119
3DB20436BA MPT-HC, 6750 - 6820 MHZ, TX HIGH N/A Active UDS-119
3DB20437BA MPT-HC, 6420 - 6600 MHZ, TX LOW N/A Active UDS-119
3DB20438BA MPT-HC, 6565 - 6720 MHZ, TX LOW N/A Active UDS-119
3DB20439BA MPT-HC, 6760 - 6940 MHZ, TX HIGH N/A Active UDS-119
3DB20440BA MPT-HC, 6905 - 7060 MHZ, TX HIGH N/A Active UDS-119
3DB20441BA MPT-HC, 5929 - 6050 MHZ, TX LOW N/A Active UDS-119
3DB20442BA MPT-HC, 6047.96 - 6168 MHZ, TX LOW N/A Active UDS-119
3DB20443BA MPT-HC, 6182 - 6302.04 MHZ, TX HIGH N/A Active UDS-119
3DB20444BA MPT-HC, 6300 - 6420.04 MHZ, TX HIGH N/A Active UDS-119
3DB20454BC MPT-HC, 7107 - 8377 MHZ, TX LOW N/A Active UDS-119
3DB20456BC MPT-HC, 7261 - 8496.114 MHZ, TX HIGH N/A Active UDS-119
3DB20462BA MPT-HC, 6640 - 6710 MHZ, TX LOW N/A Active UDS-119
3DB20563BA MPT-HC, 6800 - 6870 MHZ, TX HIGH N/A Active UDS-119
3DB20464BA MPT-HC, 6595 - 6775 MHZ, TX LOW N/A Active UDS-119
3DB20465BA MPT-HC, 6935 - 7115 MHZ, TX HIGH N/A Active UDS-119
3DB20473BA MPT-HC, 21198 - 21819 MHZ, TX LOW CRMYAB3JRA Active UDS-119
3DB20474BA MPT-HC, 21781 - 22400 MHZ, TX LOW CRMYAB5JRA Active UDS-119
3DB20475BA MPT-HC, 22400 - 23019 MHZ, TX HIGH CRMYAB4JRA Active UDS-119
3DB20476BA MPT-HC, 22981 - 23600 MHZ, TX HIGH CRMYAB6JRA Active UDS-119
3DB20546BA MPT-HC, 10935 - 11205 MHZ, TX LOW CRMYAB9JRA Inactive UDS-119
3DB20546BB MPT-HC, 10935 - 11205 MHZ, TX LOW N/A Active UDS-119
3DB20547BA MPT-HC, 11205 - 11485 MHZ, TX HIGH CRMYAB8JRA Inactive UDS-119
3DB20547BA MPT-HC, 11205 - 11485 MHZ, TX HIGH N/A Active UDS-119
3DB20548BA MPT-HC, 11445 - 11705 MHZ, TX HIGH CRMYAB6JRA Inactive UDS-119
3DB20548BB MPT-HC, 11445 - 11705 MHZ, TX HIGH N/A Active UDS-119

9500 MPR-A unit data sheet cross-reference 3-11

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
3DB20563BA MPT-HC, 39300 - 39650 MHZ, TX HIGH N/A Active UDS-119
3DB20562BA MPT-HC, 38950 - 39300 MHZ, TX LOW N/A Active UDS-119
3DB20564BA MPT-HC, 39650 - 40000 MHZ, TX HIGH N/A Active UDS-119
3DB20760BA MPT-XP, 5929.96 - 6168 MHZ, TX LOW N/A Active UDS-119
3DB20761BA MPT-XP, 6182 - 6420.04 MHZ, TX HIGH N/A Active UDS-119
3DB20763BA MPT-XP, 6420 - 6775 MHZ, TX LOW N/A Active UDS-119
3DB20764BA MPT-XP, 6710 - 7115 MHZ, TX HIGH N/A Active UDS-119
3DB20771BA MPT-XP, 7107 - 7714.5 MHZ, TX LOW N/A Active UDS-119
3DB20772BA MPT-XP, 7261 - 7911 MHZ, TX HIGH N/A Active UDS-119
3DB20773BA MPT-XP, 7725 - 8377 MHZ, TX LOW N/A Active UDS-119
3DB20774BA MPT-XP, 8025 - 8496.114 MHZ, TX HIGH N/A Active UDS-119
3DB20800BA MPT-HC, 5929.96 - 6168 MHZ, TX LOW N/A Active UDS-119
3DB20802BA MPT-HC, 6182 - 6420.04 MHZ, TX HIGH N/A Active UDS-119
3DB20804BA MPT-HC, 6420 - 6775 MHZ, TX LOW N/A Active UDS-119
3DB20806BA MPT-HC, 6710 - 7115 MHZ, TX HIGH N/A Active UDS-119
3DB20913BA 9558HC, 5725.5-5785.5 MHz, TX LOW N/A Active UDS-119
3DB20914BA 9558HC, 5789.5-5849.5 MHz, TX HIGH N/A Active UDS-119
ODU300 W/LIGHTNING SURGE SUPPRESSOR, 8 GHz, 300 MHz SEPARATION UDS-108
3DB23033HA ODU300, 7722.5 - 7859 MHz, HP, TX Low N/A Active
3DB23033HC ODU300, 8025 - 8171 MHz, HP, TX High N/A Active
3DB23033HB ODU300, 7844 - 7981 MHz, HP, TX Low N/A Active
3DB23033HD ODU300, 8145 - 8287 MHz, HP, TX High N/A Active
ODU300 11 GHz, 590-490 MHz SEPARATION UDS-108
3DB23035AA ODU300, 10675 - 10835 MHZ, TX LOW N/A Inactive
3DB23035AB ODU300, 10795 - 10955 MHZ, TX LOW N/A Inactive
3DB23035AC ODU300, 10915 - 11075 MHZ, TX LOW N/A Inactive
3DB23035AD ODU300, 11035 - 11200 MHZ, TX LOW N/A Inactive
3DB23035AE ODU300, 11200 - 11345 MHZ, TX HIGH N/A Inactive
3DB23035AF ODU300, 11310 - 11465 MHZ, TX HIGH N/A Inactive
3DB23035AG ODU300, 11430 - 11585 MHZ, TX HIGH N/A Inactive
3DB23035AH ODU300, 11550 - 11705 MHZ, TX HIGH N/A Inactive

3-12 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
ODU300 W/LIGHTNING SURGE SUPPRESSOR 11 GHz, 590-490 MHz SEPARATION UDS-108
3DB23035HA ODU300, 10675 - 10835 MHZ, TX LOW CRMMC00ARB Active
3DB23035HB ODU300, 10795 - 10955 MHZ, TX LOW CRMME00ARB Active
3DB23035HC ODU300, 10915 - 11075 MHZ, TX LOW CRMMG00ARB Active
3DB23035HD ODU300, 11035 - 11200 MHZ, TX LOW CRMMJ00ARB Active
3DB23035HE ODU300, 11200 - 11345 MHZ, TX HIGH CRMMD00ARB Active
3DB23035HF ODU300, 11310 - 11465 MHZ, TX HIGH CRMMF00ARB Active
3DB23035HG ODU300, 11430 - 11585 MHZ, TX HIGH CRMMH00ARB Active
3DB23035HH ODU300, 11550 - 11705 MHZ, TX HIGH CRMMK00ARB Active
ODU300 15 GHz, 475/490 MHz SEPARATION UDS-108
3DB23039AC ODU300, 14500 - 14660 MHZ, TX LOW N/A Inactive
3DB23039AD ODU300, 14975 - 15135 MHZ, TX HIGH N/A Inactive
ODU300 W/LIGHTNING SURGE SUPPRESSOR 15 GHz, 475/490 MHz SEPARATION UDS-108
3DB23039HC ODU300, 14500 - 14660 MHZ, TX LOW N/A Active
3DB23039HD ODU300, 14975 - 15135 MHZ, TX HIGH N/A Active
ODU300 18 GHz, 340 MHz SEPARATION UDS-108
3DB23041AA ODU300, 18580 - 18660 MHZ, TX LOW N/A Inactive
3DB23041AB ODU300, 18660 - 18740 MHZ, TX LOW N/A Active
3DB23041AC ODU300, 18740 - 18820 MHZ, TX LOW N/A Inactive
3DB23041AD ODU300, 18920 - 19000 MHZ, TX HIGH N/A Active
3DB23041AE ODU300, 19000 - 19080 MHZ, TX HIGH N/A Inactive
3DB23041AF ODU300, 19080 - 19160 MHZ, TX HIGH N/A Active
ODU300 18 GHz, 1008/1010/1092/1120 MHz SEPARATION UDS-108
3DB23042AA ODU300, 17700 - 18060 MHZ, TX LOW N/A Active
3DB23042AB ODU300, 17905 - 18275 MHZ, TX LOW N/A Active
3DB23042AC ODU300, 18110 - 18490 MHZ, TX LOW N/A Inactive
3DB23042AD ODU300, 18330 - 18690 MHZ, TX LOW N/A Inactive
3DB23042AE ODU300, 18710 - 19070 MHZ, TX HIGH N/A Active
3DB23042AF ODU300, 18920 - 19290 MHZ, TX HIGH N/A Inactive
3DB23042AG ODU300, 19130-19510 MHZ, TX HIGH N/A Active
3DB23042AH ODU300, 19340 - 19700 MHZ, TX HIGH N/A Inactive

9500 MPR-A unit data sheet cross-reference 3-13

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
ODU300 23 GHz, 1200 MHz SEPARATION UDS-108
3DB23045AA ODU300, 21200 - 21570 MHZ, TX LOW N/A Inactive
3DB23045AB ODU300, 21475 - 21845 MHZ, TX LOW N/A Inactive
3DB23045AC ODU300, 21750 - 22120 MHZ, TX LOW N/A Inactive
3DB23045AD ODU300, 22030 - 22400 MHZ, TX LOW N/A Inactive
3DB23045AE ODU300, 22400 - 22770 MHZ, TX HIGH N/A Inactive
3DB23045AF ODU300, 22675 - 23045 MHZ, TX HIGH N/A Inactive
3DB23045AG ODU300, 22950 - 23320 MHZ, TX HIGH N/A Inactive
3DB23045AH ODU300, 23230 - 23600 MHZ, TX HIGH N/A Inactive
ODU300 W/LIGHTNING SURGE SUPPRESSOR 23 GHz, 1200 MHz SEPARATION UDS-108
3DB23045HA ODU300, 21200 - 21570 MHZ, TX LOW CRMMN00ARB Active
3DB23045HB ODU300, 21475 - 21845 MHZ, TX LOW CRMMR00ARB Active
3DB23045HC ODU300, 21750 - 22120 MHZ, TX LOW CRMMT00ARB Active
3DB23045HD ODU300, 22030 - 22400 MHZ, TX LOW CRMMV00ARB Active
3DB23045HE ODU300, 22400 - 22770 MHZ, TX HIGH CRMMP00ARB Active
3DB23045HF ODU300, 22675 - 23045 MHZ, TX HIGH CRMMS00ARB Active
3DB23045HG ODU300, 22950 - 23320 MHZ, TX HIGH CRMMU00ARB Active
3DB23045HH ODU300, 23230 - 23600 MHZ, TX HIGH CRMMW00ARB Active
ODU300 W/LIGHTNING SURGE SUPPRESSOR 23 GHz, 1200 MHz SEPARATION, HIGH UDS-108
POWER
3DB23045HI ODU300, 21200 - 21570 MHZ, TX LOW, HP N/A Active
3DB23045HJ ODU300, 21475 - 21845 MHZ, TX LOW, HP N/A Active
3DB23045HK ODU300, 21750 - 22120 MHZ, TX LOW, HP N/A Active
3DB23045HL ODU300, 22030 - 22400 MHZ, TX LOW, HP N/A Active
3DB23045HM ODU300, 22400 - 22770 MHZ, TX HIGH, HP N/A Active
3DB23045HN ODU300, 22675 - 23045 MHZ, TX HIGH, HP N/A Active
3DB23258HO ODU300, 22950 - 23320 MHZ, TX HIGH, HP N/A Active
3DB23045HP ODU300, 23230 - 23600 MHZ, TX HIGH, HP N/A Active
ODU300 18 GHz, 1560 MHz SEPARATION UDS-108
3DB23062AC ODU300, 17700 - 18060 MHZ, TX LOW N/A Inactive
3DB23062AD ODU300, 19260 - 19620 MHZ, TX HIGH N/A Inactive
ODU300 W/LIGHTNING SURGE SUPPRESSOR 18 GHz, 1560 MHz SEPARATION UDS-108
3DB23062HC ODU300, 17700 - 18060 MHZ, TX LOW CRMML00ARB Active
3DB23062HD ODU300, 19260 - 19620 MHZ, TX HIGH CRMMM00ARB Active
ODU300 W/LIGHTNING SURGE SUPPRESSOR 18 GHz, 1560 MHz SEPARATION, HIGH UDS-108
POWER

3-14 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
3DB23062HE ODU300, 17700 - 18140 MHZ, TX LOW, HP N/A Active
3DB23062HF ODU300, 19260 - 19700 MHZ, TX HIGH, HP N/A Active
ODU300, U6 GHz, 160 MHz SEPARATION UDS-108
3DB23214AA ODU300, 6540 - 6610 MHZ, HP, TX LOW N/A Inactive
3DB23214AB ODU300, 6710 - 6780 MHZ, HP, TX HIGH N/A Inactive
3DB23214AC ODU300, 6590 - 6660 MHZ, HP, TX LOW N/A Inactive
3DB23214AD ODU300, 6760 - 6830 MHZ, HP, TX HIGH N/A Inactive
3DB23214AE ODU300, 6640 - 6710 MHZ, HP, TX LOW N/A Inactive
3DB23214AF ODU300, 6800 - 6870 MHZ, HP, TX HIGH N/A Inactive
ODU300 W/LIGHTNING SURGE SUPPRESSOR, U6 GHz, 160 MHz SEPARATION UDS-108
3DB23214HA ODU300, 6540 - 6610 MHZ, HP, TX LOW CRMLZ10HRB Active
3DB23214HB ODU300, 6710 - 6780 MHZ, HP, TX HIGH CRML110HRB Active
3DB23214HC ODU300, 6590 - 6660 MHZ, HP, TX LOW CRML210HRB Inactive
3DB21214HD ODU300, 6760 - 6830 MHZ, HP, TX HIGH CRML310HRB Inactive
3DB23214HE ODU300, 6640 - 6710 MHZ, HP, TX LOW CRML410HRB Inactive
3DB23214HF ODU300, 6800 - 6870 MHZ, HP, TX HIGH CRML510HRB Inactive
ODU300 L6 GHz, 252.04 MHz SEPARATION UDS-108
3DB23215AA ODU300, 5930 - 6020 MHZ, HP, TX LOW N/A Inactive
3DB23215AB ODU300, 5989 - 6079 MHZ, HP, TX LOW N/A Inactive
3DB23215AC ODU300, 6078 - 6168 MHZ, HP, TX LOW N/A Inactive
3DB23215AD ODU300, 6182 - 6272 MHZ, HP, TX HIGH N/A Inactive
3DB23215AE ODU300, 6241 - 6331 MHZ, HP, TX HIGH N/A Inactive
3DB23215AF ODU300, 6330 - 6420 MHZ HP, TX HIGH N/A Inactive
ODU300 W/LIGHTNING SURGE SUPPRESSOR L6 GHz, 252.04 MHz SEPARATION UDS-108
3DB23215HA ODU300, 5930 - 6020 MHZ, HP, TX LOW CRMLT10HRB Active
3DB23215HB ODU300, 5989 - 6079 MHZ, HP, TX LOW CRMLV10HRB Active
3DB23215HC ODU300, 6078 - 6168 MHZ, HP, TX LOW CRMLX10HRB Active
3DB23215HD ODU300, 6182 - 6272 MHZ, HP, TX HIGH CRMLU10HRB Active
3DB23215HE ODU300, 6241 - 6331 MHZ, HP, TX HIGH CRMLW10HRB Active
3DB23215HF ODU300, 6330 - 6420 MHZ HP, TX HIGH CRMLY10HRB Active

9500 MPR-A unit data sheet cross-reference 3-15

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
ODU300, U6 GHz, 340 MHz SEPARATION UDS-108
3DB23216AA ODU300, 6430 - 6590 MHz, HP TX LOW N/A Inactive
3DB23216AB ODU300, 6770 - 6930 MHz, HP TX HIGH N/A Inactive
3DB23216AC ODU300, 6515 - 6675 MHz, HP TX LOW N/A Inactive
3DB23216AD ODU300, 6855 - 7015 MHz, HP TX HIGH N/A Inactive
3DB23216AE ODU300, 6600 - 6760 MHz, HP TX LOW N/A Inactive
3DB23216AF ODU300, 6940 - 7100 MHz, HP TX HIGH N/A Inactive
ODU300 W/LIGHTNING SURGE SUPPRESSOR, U6 GHz, 340 MHz SEPARATION UDS-108
3DB23216HA ODU300, 6430 - 6590 MHz, HP TX LOW CRML610HRB Active
3DB23216HB ODU300, 6770 - 6930 MHz, HP TX HIGH CRML710HRB Active
3DB23216HC ODU300, 6515 - 6675 MHz, HP TX LOW CRML810HRB Active
3DB23216HD ODU300, 6855 - 7015 MHz, HP TX HIGH CRML910HRB Active
3DB23216HE ODU300, 6600 - 6760 MHz, HP TX LOW CRMMA00ARB Active
3DB23216HF ODU300, 6940 - 7100 MHz, HP TX HIGH CRMMB00ARB Active
ODU300 W/LIGHTNING SURGE SUPPRESSOR, 7 GHz, 150 MHz SEPARATION UDS-108
3DB23217HA ODU300, 7424 - 7485 MHz, HP, TX Low N/A Active
3DB23218HA ODU300, 7574 - 7635 MHz, HP, TX High N/A Active
3DB23219HA ODU300, 7470 - 7530 MHz, HP, TX Low N/A Active
3DB23220HA ODU300, 7620 - 7680 MHz, HP, TX High N/A Active
3DB23221HA ODU300, 7515 - 7575 MHz, HP, TX Low N/A Active
3DB23222HA ODU300, 7665 - 7725 MHz, HP, TX High N/A Active
ODU300 W/LIGHTNING SURGE SUPPRESSOR, 7 GHz, 175 MHz SEPARATION UDS-108
3DB23223HA ODU300, 7124 - 7185 MHz, HP, TX Low N/A Active
3DB23224HA ODU300, 7299 - 7360 MHz, HP, TX High N/A Active
3DB23225HA ODU300, 7157.5 - 7217.5 MHz, HP, TX Low N/A Active
3DB23226HA ODU300, 7332.5 - 7392.5 MHz, HP, TX High N/A Active
3DB23227HA ODU300, 7190 - 7250 MHz, HP, TX Low N/A Active
3DB23228HA ODU300, 7365 - 7425 MHz, HP, TX High N/A Active

3-16 9500 MPR-A unit data sheet cross-reference

UDS-100 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART UDS
NUMBER DESCRIPTION CLEI STATUS NUMBER
ODU300 W/LIGHTNING SURGE SUPPRESSOR 38 GHz, 700 MHz SEPARATION UDS-108
3DB23258HO ODU300, 38600 - 38800 MHZ, TX LOW N/A Active
3DB23258HP ODU300, 39300 - 39500 MHZ, TX HIGH N/A Active
3DB23258HQ ODU300, 38750 - 38950 MHZ, TX LOW N/A Active
3DB23258HR ODU300, 39450 - 39650 MHZ, TX HIGH N/A Active
3DB23258HS ODU300, 38950 - 39150 MHZ, TX LOW N/A Active
3DB23258HT ODU300, 39650 - 39850 MHZ, TX HIGH N/A Active
3DB23258HU ODU300, 39100 - 39300 MHZ, TX LOW N/A Active
3DB23258HV ODU300, 39800 - 40000 MHZ, TX HIGH N/A Active
3EM13317AA PDU Power Distribution Unit N/A Active UDS-112
3EM20277AA GigE SFP 1000Base-SX, 850 nm DRR3AA3CAA Active UDS-111
3EM20277AB GigE SFP 1000Base-LX, 1310 nm DRR3AA4CAA Active UDS-111
3EM20277AC GigE SFP 1000Base-EX, 1310 nm DRR3AA5CAA Active UDS-111
3EM20277AD GigE SFP 1000Base-ZX, 1550 nm DRR3AA6CAA Active UDS-111
3EM22617AA MPT-HL Transceiver L6, 5725-6425 MHz CRTUAAXFAA Active UDS-109
3EM22617AB MPT-HL Transceiver U6, 6425-6930 MHz CRTUAAYFAA Active UDS-109
3EM22617AC MPT-HL Transceiver L6, 5925-6425 MHz, CRTUABLFAA Active UDS-109
HP
3EM22617AD MPT-HL Transceiver U6, 6425-6930 MHz, CRTUABMFAA Active UDS-109
HP
3EM22618AB MPT-HL Microwave Packet transport-Long N/A Active UDS-102
Haul Shelf
3EM22900AA DS3 Hybrid Splitter N/A Active UDS-116
3EM23272AA Type N Adapter Bracket N/A Active UDS-114
3EM23888AA MPT-HL Transceiver 10.5, 10400-10700 CRTUABPCAA Active UDS-109
MHz
3EM23888AB MPT-HL Transceiver 11, 10700-11200 MHz CRTUABRCAA Active UDS-109
3EM23888AC MPT-HL Transceiver 11, 11200-11700 MHz CRTUABSCAA Active UDS-109
3EM23911AA Fan 2U Card W/Alarms CRCCADYJAA Active UDS-110
3EM24462AA DS3 Patch Panel N/A Active UDS-116
3EM24627AA MPT-HL Transceiver 7, 7125-7775 MHz N/A Active UDS-109
3EM24627AB MPT-HL Transceiver 8, 7725-8500 MHz N/A Active UDS-109

9500 MPR-A unit data sheet cross-reference 3-17

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-100

3-18 9500 MPR-A unit data sheet cross-reference

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-101
MSS-8 microwave service switch shelf
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18485AA MSS-8 Microwave Service N/A 459923 213266 Inactive
Switch Shelf
3DB18485AB MSS-8 Microwave Service CRMLB10HRA 459923 213266 Active
Switch Shelf

MSS-8 microwave service switch shelf 3-15

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Features and application notes

• The Microwave Service Switch (MSS-8) shelf provides cross-

connection, port aggregation, switching, and equipment management.

• 300 Mbps full-duplex Ethernet transport capacity

• Flexible aggregate capacity sharing DS1, DS3, OC-3, and Ethernet

traffic

• Split mount configuration supports up to six unprotected RF channels,

three 1+1 HSB, Space Diversity (SD) or Frequency Diversity (FD)
protected RF channels in one MSS-8 shelf connected to up to six
OutDoor Units (ODUs).

• Split mount configuration utilizing the MPTACC card supports up to

twelve unprotected RF channels, up to six 1+1 HSB, Space Diversity
(SD) or Frequency Diversity (FD) protected RF channels in one MSS-8
shelf connected to up to twelve MPT-HC/XP Transceivers.

• Split mount configuration utilizing the Core-E SFP ports support up

to two unprotected RF channels in one MSS-8 shelf connected to up to
two MPT-HC/XP and/or MPT-GC Transceivers.

• Split mount configuration utilizing the Core-E electrical Ethernet

ports support up to four unprotected RF channels in one MSS-8 shelf
connected to up to four MPT-HC/XP and/or MPT-GC Transceivers.

• Split mount configuration utilizing the P8ETH SFP ports support up

to eighteen unprotected RF channels in one MSS-8 shelf connected to
up to eighteen MPT-HC/XP Transceivers.

• All indoor mount supports up to eighteen unprotected RF channels,

nine 1+1 HSB, Space Diversity (SD) or Frequency Diversity (FD)
protected RF channels in one MSS-8 shelf using P8ETH cards
connected to up to nine Microwave Packet Transport-Long Haul
(MPT-HL) shelves.

• Stand-alone shelf configuration

• All cards are accessed from the front side of the shelf

• Mounts in a 19-inch aluminum rack or 19-inch seismic rack. Adapter

flanges available to mount in a 23-inch aluminum rack

3-16 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

• Provides two mounting depth options: flush mount or 5 inch projection

• Provides nine card slots. Two are dedicated for Control and Switching
Modules (Core-E). Six universal slots are available for transport cards:
P32E1DS1 (DS1), P2E3DS3 (DS3), SDHACC (OC-3), MOD300
(RADIO) and/or P8ETH (Ethernet). Slot 8 also supports the AUX
(Auxiliary) card. One slot is dedicated for fan card.

Description

The MSS-8 self consists of a module cage and backplane which provides nine
slots. Two dedicated slots for Core-E cards. Six slots are available for transport
cards: P32E1DS1 (DS1), P2E3DS3 (DS3), SDHACC (OC-3), MOD300 (Radio),
and/or P8ETH (Ethernet). One slot is dedicated for a required fan card. See
figure 101-1 for an example of the MSS-8 shelf.

The MSS-8 shelf is 19 inches wide (17.25 inches wide without mounting
flanges), 3.46 inches high (2 EIA rack increments), and 9.75 inches deep.
Adapter plates are available to mount the MSS-8 shelf in 23 inch aluminum
racks. See figure 101-2 for outline and shelf dimensions of the MSS-8 shelf.

Figure 101-1. Microwave service switch (MSS-8) shelf

MSS-8 microwave service switch shelf 3-17

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Figure 101-2. MSS-8 shelf dimensions

MSS-8 Shelf

3.46

9.75

17.25
950-0040-1
062110

Equipment complement

MSS-8 shelf slots 1 and 2 are dedicated to the Core-E card. Slots 3 through 8
are available for transport cards P32E1DS1, P2E3DS3, MPTACC, MOD300,
SDHACC, and/or P8ETH. Slot 9 is dedicated for required fan card. See
figure 101-3 for MSS-8 shelf slot definitions. Refer to Table 101-A for details of
card equipage options.

3-18 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 101-3. MSS-8 shelf slot definitions

1 CSM-E 2 9
CSM-E
(Main) (Spare)

3 4
Transport Card Transport Card

Fan
5 6
Transport Card Transport Card

7 8 Transport Card
Transport Card or
Auxiliary Card

950-0003-3
092010

MSS-8 microwave service switch shelf 3-19

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Table 101-A. MSS-8 shelf card complement

CIRCUIT PACK/
UNIT DATA SHEET PART NO. CLEI QTY SLOT
CSM-E Enhanced Control and 3DB18326AC CRCCAEVEAA 1 1
Switching Module
UDS-103
CSM-E Enhanced Control and 3DB18326AC CRCCAEVEAA Up to 1 2
Switching Module
UDS-103
MOD300 Radio Interface 3DB18136AE CRG2ABWDAA Up to 6 3, 4, 5, 6, 7, 8
UDS-104
MOD300EN Radio Interface 3DB18538AC CRG2ABWDAA Up to 2 3, 4, 5, 6, 7, 8
UDS-104
MPTACC MPT Access 3DB18634AB N/A Up to 6 3, 4, 5, 6, 7, 8
UDS-118
P2E3DS3 DS3 PDH Card 3DB18194AC CRG2AA9DAA Up to 6 3, 4, 5, 6, 7, 8
UDS-106
P8ETH Ethernet Access Switch 3DB18206AC CRCCACGJAA Up to 2 3, 4, 5, 6, 7, 8
Card
UDS-107
P32E1DS1 DS1 PDH Card 3DB18126AE CRG2ABUDAA Up to 6 3, 4, 5, 6, 7, 8
UDS-105
SDHACC OC-3 SDH Card 3DB18735AA N/A Up to 6 3, 4, 5, 6, 7, 8
UDS-125
AUX Auxiliary Card 3DB18236AB N/A Up to 1 8
UDS-120
+24/-48 Volt Converter (2 3DB18862AA N/A Up to 1 4, 6, 8
Converters W/Chassis) 1
or
+24/-48 Volt Converter (1 Converter 3DB18863AA N/A
W/Chassis)1
UDS-122
Fan 2U Card 3DB18134BB CRCCACPJAA 1 9
or
Fan 2U Card W/Alarms 3EM23911AA CRCCADYJAA
UDS-110
[1] For shelves equipped with the +24/-48 Volt Converter card, the FAN 2U Card W/Alarms is required.

3-20 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

MSS-8 shelf slot 1 is dedicated to the main Core-E card and is required in every
application. See figure 101-4 to see an example of the MSS-8 shelf configured
in the unprotected Core-E configuration. Slot 2 is dedicated for an optional
spare Core-E card for protected Core-E configurations. See figure 101-5 to see
an example of the MSS-8 shelf configured in the protected Core-E
configuration.

Figure 101-4. MSS-8 shelf, unprotected Core-E configuration

1 CSM-E 2 9
(Main) Filler Panel

3 4
Any Transport Any Transport
Fan
5 6
Any Transport Any Transport

7 8 Any Transport
Any Transport or
Auxiliary Card

950-0006-2
091410

MSS-8 microwave service switch shelf 3-21

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Figure 101-5. MSS-8 shelf, protected Core-E configuration

1 CSM-E 2 9
CSM-E
(Main) (Spare)

3 4
Any Transport Any Transport
Fan
5 6
Any Transport Any Transport

7 8 Any Transport
Any Transport or
Auxiliary Card

950-0005-3
091410

MSS-8 shelves supports up to six P32E1DS1 cards in unprotected DS1

aggregation configurations. Supports up to three pairs of P32E1DS1 cards in
1+1 EPS protected DS1 aggregation configurations. In 1+1 EPS protected
configuration, the main P32E1DS1 cards are equipped in slots 3, 5, and/or 7,
and the spare (protection) P32E1DS1 cards are equipped in slots 4, 6, and/or 8
respectively.

See figure 101-6 to see an example of a stand-alone MSS-8 shelf configured

with two pairs of P32E1DS1s in slots 3 through 6 in the protected 1+1 EPS
configuration and slots 7 and 8 configured in the unprotected configuration.

3-22 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 101-6. MSS-8 stand-alone shelf, equipped with P32E1DS1 (DS1 Card)

1 CSM-E 2 CSM-E 9
(Main) (Spare)

3 4
P32E1DS1 P32E1DS1
(Main) (Spare)
Fan
5 6
P32E1DS1 P32E1DS1
(Main) (Spare)

7 P32E1DS1 8
P32E1DS1
(Unprotected) (Unprotected)

950-0007-3
091410

MSS-8 shelves supports up to six P2E3DS3 cards in unprotected

configurations. Supports up to three pairs of P2E3DS3 cards in 1+1 EPS
protected configurations. In 1+1 EPS protected configuration, the main
P2E3DS3 cards are equipped in slots 3, 5, and/or 7, and the spare (protection)
P2E3DS3 cards are equipped in slots 4, 6, and/or 8 respectively.

See figure 101-7 to see an example of a stand-alone MSS-8 shelf configured

with two pairs of P2E3DS3s in slots 3 through 6 in the protected 1+1 EPS
configuration and slots 7 and 8 configured in the unprotected configuration.

MSS-8 microwave service switch shelf 3-23

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Figure 101-7. MSS-8 stand-alone shelf, equipped with P2E3DS3 (DS3 Card)

1 CSM-E 2 CSM-E 9
(Main) (Spare)

3 4
P2E3DS3 P2E3DS3
(Main) (Spare)
Fan
5 6
P2E3DS3 P2E3DS3
(Main) (Spare)

7 P2E3DS3 8 P2E3DS3
(Unprotected) (Unprotected)

950-0008-3
091410

MSS-8 shelves supports up to six SDHACC cards in unprotected

configurations. Supports up to three pairs of SDHACC cards in 1+1 EPS
protected configurations. In 1+1 EPS protected configuration, the main
SDHACC cards are equipped in slots 3, 5, and/or 7, and the spare (protection)
SDHACC cards are equipped in slots 4, 6, and/or 8 respectively.

MSS-8 shelves supports up to six MOD300 cards in unprotected RF radio

configurations. Supports up to three pairs of MOD300 cards in protected RF
radio in 1+1 HSB, SD or FD configurations. In 1+1 HSB, SD or FD
configurations, the main MOD300 cards are equipped in slots 3, 5, and/or 7,
and the spare (protection) MOD300 cards are equipped in slots 4, 6, and/or 8
respectively.

See figure 101-8 to see an example of the MSS-8 shelf configured as a split
mount, 1+0 drop and insert repeater in slots 7 and 8, with a pair of P32E1DS1s
in slots 3 and 4 in the protected 1+1 EPS configuration, and with a pair of
P2E3DS3s in slots 5 and 6 in the protected 1+1 EPS configuration.

See figure 101-9 to see an example of the MSS-8 shelf configured as a split
mount, 1+1 drop and insert repeater in slots 5 through 8, with a P32E1DS1s in
slot 3 in the unprotected configuration, and with a P2E3DS3 in slot 4 in the
unprotected configuration.

3-24 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 101-8. MSS-8 shelf, split mount, 1+0 drop and insert repeater configuration

1 CSM-E 2 9
CSM-E
(Main) (Spare)

3 4
P32E1DS1 P32E1DS1
(Main) (Spare)
Fan
5 6
P2E3DS3 P2E3DS3
(Main) (Spare)

7 8
MOD300 MOD300
(Unprotected) (Unprotected)

950-0009-3
091410

Figure 101-9. MSS-8 shelf, split mount, 1+1 drop and insert repeater configuration

1 CSM-E 2 9
CSM-E
(Main) (Spare)

3 4
P32E1DS1 P2E3DS3
(Unprotected) (Unprotected)
Fan
5 6
MOD300 MOD300
(Main) (Spare)

7 8
MOD300 MOD300
(Main) (Spare)

950-0010-3
091410

MSS-8 microwave service switch shelf 3-25

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

MSS-8 shelves supports up to six MPTACC cards in unprotected configuration,

up to twelve RF radio channels. Supports three pairs of MPTACC cards in
protected 1+1 HSB/FD configuration, up to six protected RF radio channels. In
1+1 HSB, SD or FD configuration, the main MPTACC card is equipped in slot
3, 5, and/or 7 and the spare (protection) MPTACC card is equipped in slot 4, 6,
and/or 8 respectively.

See figure 101-10 to see an example of the MSS-8 shelf configured as a split
mount, unprotected Core-E, 12-way nodal junction in slots 3 through 8.

See figure 101-11 to see an example of the MSS-8 shelf configured as a

protected Core-E, 1+1 protected 4-way junction in slots 5 through 8, and slots
3 and 4 configured in the unprotected DS1 configuration.

Figure 101-10. MSS-8 shelf, split mount MPT-HC/XP, 1+0 12-way nodal junction configuration

1 CSM-E 2 9
(Main) Filler Panel

3 4
MPT Access MPT Access
(Main) (Main)
Fan
5 6
MPT Access MPT Access
(Main) (Main)

7 8
MPT Access MPT Access
(Main) (Main)

950-0046-1
030311

3-26 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 101-11. MSS-8 shelf, all indoor mount, 1+1 4-way junction configuration

1 CSM-E 2 CSM-E 9
(Main) (Spare)

3 4
P32E1DS1 P32E1DS1
(Unprotected) (Unprotected)
Fan
5 6
MPT Access MPT Access
(Main) (Spare)

7 8
MPT Access MPT Access
(Main) (Spare)

950-0047-1
030311

MSS-8 shelves equipped with P8ETH cards, the P8ETH is supported in slots 3
through 8. For stacked P8ETH applications, the main P8ETH card resides in
slot 3, 5, and/or 7 and the spare P8ETH resides in slots 4, 6, and/or 8.

See figure 101-12 to see an example of the MSS-8 shelf configured as an all
indoor mount, 1+0 4-way junction in slot 3, with a pair of P32E1DS1s in slots
5 and 6 in the protected 1+1 EPS configuration.

See figure 101-13 to see an example of the MSS-8 shelf configured as an all
indoor mount, 1+1 4-way junction in slots 3 and 4, with three P32E1DS1s in
slots 5 through 7 in the unprotected configuration.

MSS-8 microwave service switch shelf 3-27

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Figure 101-12. MSS-8 shelf, all indoor mount, 1+0 4-way junction configuration

1 CSM-E 2 9
CSM-E
(Main) (Spare)

3 4
P8ETH
Filler Panel
(Main)
Fan
5 6
P32E1DS1 P32E1DS1
(Main) (Spare)

7 8
Filler Panel Filler Panel

950-0011-3
091410

Figure 101-13. MSS-8 shelf, all indoor mount, 1+1 4-way junction configuration

1 CSM-E 2 CSM-E 9
(Main) (Spare)

3 4
P8ETH P8ETH
(Main) (Spare)
Fan
5 6
P32E1DS1 P32E1DS1
(Unprotected) (Unprotected)

7 P32E1DS1 8
(Unprotected) Filler Panel

950-0012-3
091410

3-28 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

MSS-8 shelf equipped with two P8ETH cards and four MOD300 cards support
up to a 12 spoke hub. In this configuration; main P8ETH cards are equipped in
slots 3 and 4 and support up to eight 1+0 spokes, and up to four main MOD300
cards are equipped in slots 5 through 8 and support up to four 1+0 spokes.

See figure 101-14 to see an example of the MSS-8 shelf configured as a 12 spoke
hub using all indoor mount (P8ETH/MPT-HL).

Figure 101-14. MSS-8 shelf, 1+0, 12 spoke hub configuration

1 CSM-E 2 CSM-E 9
(Main) (Spare)

3 4
P8ETH P32E1DS1
(Main) (Main)
Fan
5 6
P8ETH P32E1DS1
(Main) (Main)

7 P8ETH 8
AUX
(Main)

950-0253-1
100611

See figure 101-15 to see an example of the MSS-8 shelf configured mixing all
three radio technologies. P8ETH cards equipped in slots 3 and 4 support up to
eight MPT-HL 1+0 unprotected radio channels or as shown up to four MPT-HL
1+1 protected radio channels. MPT Access cards in slots 5 and 6 support up to
4 MPT-HC/XP 1+0 unprotected radio channels, or as shown two MPT-HC/XP
1+1 protected radio channels. The MOD300 card in slot 7 supports one
ODU300 1+0 radio channel. Slot 8 is shown with one 1+0 P32E1DS1 DS1
Interface with support for up to 32 DS1 signals. The Core-E card in slot 1 could
support up to six MPT-HC/XP 1+0 radio channels for a total support of twelve
maximum radio channels per MSS-8 shelf.

MSS-8 microwave service switch shelf 3-29

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

Figure 101-15. MSS-8 shelf, 1+0, 12 spoke hub configuration

1 CSM-E 2 CSM-E 9
(Main) (Spare)

3 4
P8ETH P8ETH
(Main) (Spare)
Fan
5 6
MPT Access MPT Access
(Main) (Spare)

7 8
MOD300 P32E1DS1
(Main) (Main)

950-0048-1
030311

Functional overview

MSS-8 implements functionality of grooming, routing, switching and

protection, exploiting a packet oriented technology in order to meet the overall
architecture.

The MSS-8 Core-E platform, with multiplexing and symmetrical cross-connect

functions, can manage different radio directions (up to fourteen), with the
possibility to add-drop data flows of local DS1/DS3/OC-3/Ethernet traffic.
Core-E platform is based on packet technology (Ethernet Switch) with a
generic serial GigE interface between Core-E and transport cards. See
figure 101-16 for a functional block diagram of the MSS-8 shelf.

3-30 MSS-8 microwave service switch shelf

UDS-101 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 101-16. MSS-8 shelf block diagram

CSM Module

Transport Module
Flash
PSU Controller
Transport Module RAM

1 GbEth
Transport Module

Ethernet
Transport Module Switch

Transport Module

LIU LIU
Transport Module

4x10/100/1000 2x1000
Electrical Electrical/Optical
Ethernet Ports Ethernet Ports

950-0013-2
111710

MSS-8 microwave service switch shelf 3-31

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-101

The MSS-8 shelf houses the following cards:

• Core-E Control and Switching Module—houses one main and one

optional spare control and switching module(s). Provides four
10/100/1000 Base-T Ethernet ports. Provides two GigE optical
Ethernet port.

• MOD300 Radio card—houses up to six MOD300 cards. In the Tx

direction, converts Ethernet packet data from the Core-E card(s) into
a modulated IF output signal that is applied to the ODU300. In the Rx
direction, demodulates the IF input signal from the ODU300,
encapsulates the digital data into Ethernet packets, and sends the
packets to the Core-E card(s).

• MPTACC MPT Access card—houses up to six MPTACC cards for

MSS-8 to two MPT-HC/XP interfaces (Ethernet and power) for split
mount configuration.

• P2E3DS3 DS3 PDH card—houses up to six P2E3DS3 cards for DS3

TDM traffic encapsulation/extraction into standard Ethernet packets

• P8ETH Ethernet Access Switch—houses up to six P8ETH cards for

MSS-8-to-MPT-HL or MSS-8-to-MPT-HC/XP interfaces. The P8ETH
card functions as a layer 2 switch, cross-connecting VLAN tagged
Ethernet data to/from the addressed MPT unit.
The P8ETH card provides traffic management for Core-Es for up to six
directions using protected radios and up to twelve directions using
unprotected radios.
P8ETH cards also provide four 10/100/1000 Base-T Ethernet ports and
up to four GigE optical Ethernet ports.

• P32E1DS1 DS1 PDH card—houses up to six P32E1DS1 cards for DS1

TDM traffic encapsulation/extraction into standard Ethernet packets

• SDHACC OC-3 SDH card—houses up to six SDHACC cards for OC-3

TDM traffic encapsulation/extraction into standard Ethernet packets

• The MSS-8 shelf houses one fan card resident in slot 9 on the
right-hand side of the shelf and provides forced-air cooling for the
shelf.

• The MSS-8 shelf houses up to one AUX card optional in slot 8 to

provide up to nine station alarm inputs and eight station alarm control
outputs.

3-32 MSS-8 microwave service switch shelf

UDS-102 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-102
MPT-HL microwave packet transport-long haul shelf
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3EM22618AB MPT-HL Microwave Packet N/A N/A N/A Active
transport-Long Haul Shelf

Features and application notes

• The Microwave Packet Transport-Long Haul (MPT-HL) shelf provides

an all indoor solution when used in conjunction with the 9500 MPR-A
MSS-8 shelf equipped with P8ETH Ethernet Access Switch.

• The MPT-HL shelf provides support for two high-capacity, long-haul

RF transmission MPT Transceivers.

• All cards are accessed from the front side of the shelf

• Mounts in a 19-inch aluminum rack or 19-inch seismic rack. Adapter

flanges available to mount in a 23-inch aluminum rack

• Provides two mounting depth options: flush mount or 5 inch projection

• Houses up to two MPT Transceivers.

Description

The MPT-HL self consists of a module cage and backplane which provides two
slots dedicated for two MPT Transceiver cards. See figure 102-1 for an example
of the MPT-HL shelf.

The MPT-HL shelf is 19 inches wide (17.25 inches wide without mounting
flanges), 4.25 inches high (2.5 EIA rack increments), and 10.5 inches deep
without diplexer and waveguide mounting brackets. Adapter plates are
available to mount the MPT-HL shelf in 23 inch aluminum racks. See figure
102-2 through figure 102-5 for outline and shelf dimensions of the MPT-HL
shelf in various configurations.

MPT-HL microwave packet transport-long haul shelf 3-33

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-102

Figure 102-1. Microwave packet transport-long haul (MPT-HL) shelf

Figure 102-2. MPT-HL shelf dimensions

MPT-HL Shelf

4.25

10.5

17.25
950-0042-1
062110

3-34 MPT-HL microwave packet transport-long haul shelf

UDS-102 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 102-3. MPT-HL shelf w/diplexer dimensions - top view

13.5

17.25
950-0041-1
062110

Figure 102-4. MPT-HL shelf w/one waveguide bracket dimensions - top view

17.0

17.25 950-0043-1
062110

MPT-HL microwave packet transport-long haul shelf 3-35

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-102

Figure 102-5. MPT-HL shelf w/two waveguide brackets dimensions - top view

22.0

17.25 950-0044-1
062110

Equipment complement

MPT-HL shelf houses one or two MPT Transceiver cards. The MPT
Transceiver cards can be configured either in 1+1 protection, one 1+0
unprotected, or two 1+0 unprotected radio channels.

3-36 MPT-HL microwave packet transport-long haul shelf

UDS-102 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 102-A. MPT-HL shelf card complement

CIRCUIT PACK/
UNIT DATA SHEET PART NO. CLEI QTY SLOT
MPT-HL Transceiver L6, 5725-6425 MHz 3EM22617AA CRTUAAXFAA 1 or 2 1, 2
UDS-109
MPT-HL Transceiver U6, 6425-6930 MHz 3EM22617AB CRTUAAYFAA
UDS-109
MPT-HL Transceiver L6, 5925-6425 MHz, 3EM22617AC CRTUABLFAA
HP
UDS-109
MPT-HL Transceiver U6, 6425-6930 MHz, 3EM22617AD CRTUABMFAA
HP
UDS-109
MPT-HL Transceiver 7, 7125-7775 MHz 3EM24627AA N/A
UDS-109
MPT-HL Transceiver 8, 7725-8500 MHz 3EM24627AB N/A
UDS-109
MPT-HL Transceiver 10.5, 10400-10700 3EM23888AA CRTUABPCAA
MHz
UDS-109
MPT-HL Transceiver 11, 10700-11200 3EM23888AB CRTUABRCAA
MHz
UDS-109
MPT-HL Transceiver 11, 11200-11700 3EM23888AC CRTUABSCAA
MHz
UDS-109

MPT-HL microwave packet transport-long haul shelf 3-37

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-102

3-38 MPT-HL microwave packet transport-long haul shelf

UDS-103 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-103
Core-E control and switching module
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18209AB CSM-B Control and N/A N/A N/A Active
Switching Module
3DB18326AC CSM-E Enhanced Control CRCCAEVEAA 175769 070VGE Active
and Switching Module

Features and application notes

The Core-E card provides the following functions:

• Four 10/100/1000 BaseT Ethernet ports

• Two GigE optical Ethernet port

• Network Management System (NMS) port

• TMN Ethernet Interface port

• MSS-8 shelf synchronization clock reference

• External clock reference input and output

• Supports unprotected and 1+1 Core-E Equipment Protection Switch

(EPS) configurations

• The active Core-E card manages communications — between all of the

peripheral cards (P32E1DS1, P2E3DS3, MOD300, ODU300,
SDHACC, MPT-HL Transceiver, and P8ETH) to provide peripheral
management, NMS, equipment configuration, event reporting and
logging, equipment database management and software downloads.

Core-E control and switching module 3-39

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-103

• Layer 2 Ethernet Switch — performs the cross-connection between the

peripheral cards and the Ethernet ports.

– The Switch shall assure to the system a complete interconnection

between all cards connected into the MSS-8 shelf.

– The Switch shall perform address learning, standard 802.1Q

management (VLAN), Layer 2 switching (MAC address, VLAN),
and QOS per system (802.1P and DiffServ).

– VLAN table and Address Tables shall be required to be

maintained/updated by the system for Core-E and Peripheral
Switches.

• Storage of Log Files for events and alarms. Storage capacity is the
most recent 500 events and 700 alarms.

Description

Purpose and function

The Control and Switching Module (Core-E - Core) performs all supervisory
functions for the 9500 MPR-A MSS and switches Ethernet packets from
peripherals to radio cards. The Core-E consists of microprocessor and Ethernet
switch circuits.

Microprocessor

The microprocessor consists of a 128 Mbyte system memory (SDRAM), 8 Mbyte

boot memory (EEPROM), and 128 Mbyte flash memory.

Options/configurations

There are no card options. The Core-E card is required in slot 1. The Spare
Core-E card resides in slot 2 when equipped.

Indicators, connectors, and control

The Control and Switch Module (Core-E) card has the following indicators,
connectors, and controls.

See Figure 103-1 for Core-E card front panel indicator and connector locations.

3-40 Core-E control and switching module

UDS-103 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Refer to Table 103-A for Core-E card indicators details.

Refer to Table 103-B for Core-E card connector details.

The Core-E card has a reset control for performing a manual hard reset of the
Core-E card.

Figure 103-1. Core-E front panel details

M - NE Major
Alarm (red)
m - NE Minor
Alarm (red)
W - NE Warning
Alarm (yellow)
A - NE Abnormal
Condition (yellow)
S - Module
Status

Reset
USB Sync Out Pushbutton
10/100/1000 Ethernet Ports 1-4 GigE SFP Ports 5-6
Connectors (RJ45) (Not Used) (Conn-Coax)

Craft Terminal Sync In

IT/TFC (Conn-Coax)
950-0021-1
(RJ45)
050610

Core-E control and switching module 3-41

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-103

Table 103-A. Core-E front panel indicator details

INDICATOR STATUS DEFINITION
Link (L) Off Link Down
On Link Up
Activity (A) Off No Tx/Rx activity
Blinking Tx/Rx activity
Major Alarm (M) On (Red) At least one alarm is present on the NE with Major severity
is present on the NE.
Minor Alarm (m) On (Red) At least one alarm is present on the NE with Minor severity
is present on the NE.
Warning Alarm (W) On (Yellow) At least one alarm is present on the NE with Warning
severity is present on the NE.
Abnormal Condition (A) On (Yellow) At least one Abnormal Condition is present on the NE.
Status (S) Off Card not equipped, not provisioned, or not powered
Green Blinking Download, Software Booting, or Flash Card Realignment
in Progress
Green In Service, Normal Operation, and Properly Provisioned
Yellow In Protect, Properly Provisioned as EPS
Red Card Fail
Red Blinking Card Mismatch

Table 103-B. Core-E front panel connector details

CONNECTOR TYPE FUNCTION
Ethernet Ports 1-4 RJ45 10/100/1000BaseT Ethernet Port
Ethernet Port 4 RJ45 TMN network interface
SFP Port SFP GigE Ethernet Optical Port
Craft Terminal/IT/TFC RJ45 Dedicated craft terminal port
USB USB Not used
Sync In Slip Fit Coax System sync input
1.0/2.3, Female
Sync Out Slip Fit Coax System sync output
1.0/2.3, Female

3-42 Core-E control and switching module

UDS-104 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-104
MOD300 radio interface
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18136AC MOD300 Radio Interface N/A N/A N/A Inactive
3DB18136AD MOD300 Radio Interface N/A N/A N/A Inactive
3DB18136AE MOD300 Radio Interface CRG2ABVDAA 171346 070VHS Active
3DB18538AC MOD300EN Radio CRG2ABWDAA 171353 070VHS Active
Interface

Features and application notes

• Supports both unprotected and 1+1 EPS protected configurations

• MOD300 supports static modulation applications

• MOD300EN supports static modulation applications and is required

for all adaptive modulation applications

Description

There are no card options. There are radio equipping options for the MOD300
card radio peripheral. One MOD300 card is required in any slot 3 through 8 for
not protected configurations. In protected radio configurations, two are
required, the main MOD300 card resides in slot 3, 5, and/or 7. The protect
MOD300 card resides in the slot directly across from the main, slot 4, 6, and/or
8. The protect MOD300 card protects the radio if the main MOD300 card fails.

Indicators, connectors, and control

See figure 104-1 for MOD300 card front panel indicator and connectors.

The MOD300 Radio Interface (MOD300) card has the following indicators,
connectors, and controls.

Refer to Table 104-A for MOD300 card indicators details.

Refer to Table 104-B for MOD300 card connector details.

MOD300 radio interface 3-43

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-104

The MOD300 card has no controls located on the card.

Figure 104-1. MOD300 card (MSS/MD300)

Table 104-A. MOD300 front panel indicator details

INDICATOR STATUS DEFINITION
Power Emission Status Off No Output Power (e.g.: Hot-Standby Transmitter,
(M) Software is Booting, or FPGA Downloading is In-Progress)
Green Normal Output Power
Yellow Forced Squelch Enabled on Craft Terminal
Red Abnormal Output Power
Status (S) Off Card not equipped, not provisioned, or not powered
Green Blinking Download, Software Booting, or Flash Card Realignment
in Progress
Green In Service, Normal Operation, and Properly Provisioned
Yellow In Protect, Properly Provisioned as EPS
Red Card Fail
Red Blinking Card Mismatch

Table 104-B. MOD300 front panel connector details

CONNECTOR TYPE FUNCTION
IF SMA IF signal to/from the ODU300

Functional overview

In the TX direction, the MOD300 card converts Ethernet packet data from the
Core-E (Control and Switching Module - Core) card(s) into a modulated IF
output signal that is applied to the ODU300.

In the RX direction, the MOD300 card demodulates the IF signal from the
ODU300, converts the demodulated signal into a digital IF signal,
encapsulates the digital data into Ethernet packets, and sends the packets to
the Core-E card(s).

3-44 MOD300 radio interface

UDS-104 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

See figure 104-2 for a block diagram of the MOD300.

Figure 104-2. MOD300 card block diagram

MOD300 Radio Access

FPGA

Air Framer
PDH/Data EPS
Tx I
Management DAC IF Tx
Tx Q
Mod DAC
IDU/ODU
Communication

MODEM
ASIC
diplexer

Air Framer RPS I

PDH/Data Rx Rx ADC IF Rx
Management Demod Q
ADC
IDU/ODU
Communication

Analog
Chain

From/To From Alternate

950-0190-1
Alternate Radio Radio Board
062710
Board for EPS for RPS

MOD300 radio interface 3-45

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-104

3-46 MOD300 radio interface

UDS-105 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-105
P32E1DS1 DS1 PDH card
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18126AD P32E1DS1 DS1 PDH Card N/A N/A N/A Inactive
3DB18126AE P32E1DS1 DS1 PDH Card CRG2ABUDAA 070VGM 171272 Active

Features and application notes

• Terminates up to 32 DS1 signals

• Framed DS1 Bi-Directional alarm management

• Bi-Directional performance monitoring on framed DS1 signals

• Encapsulation of DS1 data flows into standard Ethernet packets Inter

Working Function (IWF)

• Extraction of DS1 data flows from standard Ethernet packets IWF

• Supports both unprotected and 1+1 EPS protected configurations

• MSS-8 shelf supports up to six unprotected P32E1DS1 cards and up to

three P32E1DS1 protected pairs

Description

The P32E1DS1 card provides 32 DS1 interfaces. The MSS-8 shelf supports up
to six P32E1DS1 cards or 192 unprotected DS1 interfaces or 96 protected DS1
interfaces.

The P32E1DS1 are supported in MSS-8 slots 3 through 8 for unprotected radio
configurations. In protected radio configurations, a pair of P32E1DS1s are
required. The main P32E1DS1s are equipped in slots 3, 5, or 7 and the protect
(spare) P32E1DS1s are equipped in the slots directly across from the main (slot
4, 6, or 8). The spare P32E1DS1 card protects the radio if the main P32E1DS1
fails.

P32E1DS1 DS1 PDH card 3-47

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-105

Indicators, connectors, and control

The P32E1DS1 DS1 PDH card has the following indicator and connectors:

See Figure 105-1 for P32E1DS1 DS1 PDH card front panel indicator and
connectors.

Refer to Table 105-A for P32E1DS1 DS1 PDH card indicators details.

Refer to Table 105-B for P32E1DS1 DS1 PDH card connector details.

The P32E1DS1 DS1 PDH card has no controls located on the card.

Figure 105-1. P32E1DS1 DS1 card (MSS/DS1) front panel view

Table 105-A. P32E1DS1 DS1 card front panel indicator details

INDICATOR STATUS DEFINITION
Status (S) Off Card not equipped, not provisioned, or not powered
Green Blinking Download, Software Booting, or Flash Card Realignment
in Progress
Green In Service, Normal Operation, and Properly Provisioned
Yellow In Protect, Properly Provisioned as EPS
Red Card Fail
Red Blinking Card Mismatch

Table 105-B. P32E1DS1 DS1 card front panel connector details

CONNECTOR TYPE FUNCTION
I/O (16-1) 64 position SCSI DS1, Tx and Rx (tip and ring), interconnect
connector DS1s number 1 through 16
I/O (32-17) 64 position SCSI DS1, Tx and Rx (tip and ring), interconnect
connector DS1s number 17 through 32

3-48 P32E1DS1 DS1 PDH card

UDS-105 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Functional overview

In the transmit direction, the P32E1DS1 receives up to thirty-two DS1 signals

from the customer interfaces. Encapsulates the DS1 data flows into standard
Ethernet packets, (IWF). The Ethernet packets are sent to the cross-
connections matrix for connection to their provisioned destinations.

In the receive direction, the P32E1DS1 receives Ethernet packets from the
cross-connections matrix from their provisioned sources. Extracts the DS1 data
flows from standard Ethernet packets (IWF). The DS1 signals are sent to up to
thirty-two customer interfaces.

See figure 105-2 for a block diagram of the P32E1DS1.

Figure 105-2. P32E1DS1 DS1 block diagram

Core
P32E1DS1 - 32 Port DS1 Card

Trib TDM Over Packet

L L

PM
TX TX
32-Port
Line Facing CORE Facing
DS1
Loopback Loopback
Interface

L L
Trib TDM Over Packet

PM
RX
RX

950-0194-1
062210

P32E1DS1 DS1 PDH card 3-49

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-105

3-50 P32E1DS1 DS1 PDH card

UDS-106 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-106
P2E3DS3 DS3 PDH card
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18194AB P2E3DS3 DS3 PDH Card N/A N/A N/A Inactive
3DB18194AC P2E3DS3 DS3 PDH Card CRG2AA9DAA 167528 070SNE Active

Features and application notes

• Terminates up to two DS3 signals.

• Framed DS3 Bi-Directional alarm management

• Bi-Directional performance monitoring on framed DS3 signals

• Encapsulation of DS3 data flows into standard Ethernet packets Inter

Working Function (IWF)

• Extraction of DS3 data flows from standard Ethernet packets IWF

• Supports both unprotected and 1+1 EPS protected configurations

• MSS-8 shelf supports up to six unprotected P2E3DS3 cards and up to

three P2E3DS3 protected pairs

Description

The P2E3DS3 card provides 2 DS3 interfaces. The MSS-8 shelf supports up to
six P2E3DS3 cards or 12 unprotected DS3 interfaces or 6 protected DS3
interfaces.

The P2E3DS3 is supported in MSS-8 slots 3 through 8 for unprotected radio

configurations. In protected radio configurations, a pair of P2E3DS3s are
required. The main P2E3DS3s are equipped in slots 3, 5, and/or 7 and the
protect (spare) P2E3DS3s are equipped in the slots directly across from the
main (slots 4, 6, and/or 8). The protect (spare) P2E3DS3 card protects the radio
if the main P3E3DS3 fails.

P2E3DS3 DS3 PDH card 3-51

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-106

Indicators, connectors, and control

The P2E3DS3 DS3 PDH card has the following indicator and connectors.

See Figure 106-1 for P2E3DS3 DS3 PDH card front panel indicator and
connectors.

Refer to Table 106-A for P2E3DS3 DS3 PDH card indicators details.

Refer to Table 106-B for P2E3DS3 DS3 PDH card connector details.

The P2E3DS3 DS3 PDH card has no controls located on the card.

Figure 106-1. P2E3DS3 DS3 card (MSS/DS3) front panel view

Table 106-A. P2E3DS3 DS3 card front panel indicator details

INDICATOR STATUS DEFINITION
Status (S) Off Card not equipped, not provisioned, or not powered
Green Blinking Download, Software Booting, or Flash Card Realignment
in Progress
Green In Service, Normal Operation, and Properly Provisioned
Yellow In Protect, Properly Provisioned as EPS
Red Card Fail
Red Blinking Card Mismatch

Table 106-B. P2E3DS3 DS3 card front panel connector details

CONNECTOR TYPE FUNCTION
LINE 1 75 ohm male, IN - DS3 Rx interconnect
mini-BNC - Qty 2 OUT - DS3 Tx interconnect
LINE 2 75 ohm male, IN - DS3 Rx interconnect
mini-BNC - Qty 2 OUT - DS3 Tx interconnect

3-52 P2E3DS3 DS3 PDH card

UDS-106 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Functional overview

In the transmit direction, the P2E3DS3 receives DS3 signals from the customer
interfaces. Encapsulates the DS3 data flows into standard Ethernet packets,
(IWF). The Ethernet packets are sent to the cross-connections matrix for
connection to their provisioned destinations.

In the receive direction, the P2E3DS3 receives Ethernet packets from the
cross-connections matrix from their provisioned sources. Extracts the DS3 data
flows from standard Ethernet packets (IWF). The DS3 signals are sent to the
customer interfaces.

See figure 106-2 for a block diagram of the P2E3DS3.

Figure 106-2. P2E3DS3 DS3 block diagram

Core
P2E3DS3 - 2 Port DS3 Card

Trib TDM Over Packet

L L

PM
TX TX
2-Port
DS3 Line Facing Core Facing
Interface Loopback Loopback

L L
Trib TDM Over Packet

PM
RX
RX

950-0193-1
062210

P2E3DS3 DS3 PDH card 3-53

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-106

3-54 P2E3DS3 DS3 PDH card

UDS-107 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-107
P8ETH ethernet access switch card
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18206AC P8ETH Ethernet Access CRCCACGJAA 169403 070UPD Active
Switch Card

Features and application notes

• Terminates up to four GigE optical Ethernet SFP interfaces

• Terminates up to four 10/100/1000 10BaseT Ethernet interfaces

• Terminates up to four MPT-HL Transceiver cards

• Terminates up to four MPT-HC/XP units

• Supports both unprotected and 1+1 EPS protected configurations with

MPT-HL

• Supports unprotected configurations with MPT-HC/XP

Description

The P8ETH card provides four 10/100/1000 10BaseT Ethernet interfaces and
four GigE optical Ethernet SFP interfaces. The MSS-8 shelf supports one
protected pair of P8ETH cards or one unprotected P8ETH card.

The P8ETH is supported in MSS-8 slots 3 through 8 for unprotected radio

configurations. In protected radio configurations, a pair of P8ETHs are
required. The main P8ETH is equipped in slots 3, 5, and/or 7 and the protect
(spare) P8ETH is equipped in slots 4, 6, and/or 8 directly across from the main.
The protect (spare) P8ETH card protects the radio if the main P8ETH fails.

Indicators, connectors, and control

The P8ETH card has the following indicators, connectors, and controls.

See Figure 107-1 for P8ETH card front panel indicator and connector locations.

P8ETH ethernet access switch card 3-55

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-107

Refer to Table 107-A for P8ETH card indicators details.

Refer to Table 107-B for P8ETH card connector details.

Figure 107-1. P8ETH card (MSS/P8ETH)

10/100/1000 Ethernet Ports 1-4 GigE SFP Ports 5-8

Connectors (RJ45)

950-0102-1
091509

Table 107-A. P8ETH front panel indicator details

INDICATOR STATUS DEFINITION
Status (S) Off Card not equipped, not provisioned, or not powered
Green Blinking Download, Software Booting, or Flash Card Realignment
in Process
Green In-Service, Normal Operation, and Properly Provisioned
Yellow In Protect, Properly Provisioned as EPS
Red Card Fail
Red Blinking Card Mismatch
Link Off Link Down
On Link Up
Activity Off No Tx/Rx activity
Blinking Tx/Rx activity

Table 107-B. P8ETH front panel connector details

CONNECTOR TYPE FUNCTION
Ethernet Ports 1-4 RJ45 10/100/1000BaseT Ethernet Port
SFP Ports 5-8 SFP GigE Ethernet Optical Port

3-56 P8ETH ethernet access switch card

UDS-107 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Functional overview

The main purpose of the Ethernet Access Switch (P8ETH) module is to provide
the MSS-to-MPT interface for the 9500 MPR-A all indoor configuration. The
P8ETH module functions as a layer 2 switch, cross-connecting VLAN tagged
Ethernet data to/from the addressed MPT. The P8ETH module provides traffic
management for Core-Es for up to four directions using protected radios and up
to eight directions using not-protected radios.

A secondary purpose of the P8ETH module is to provide four RJ45

10/100/1000Base-T Ethernet ports, in addition to the four Core-E Ethernet
ports, and four SFP optical Ethernet ports, in addition to the Core-E SFP
optical Ethernet port.

See figure 107-2 for a block diagram of the P8ETH.

Figure 107-2. P8ETH block diagram

P8ETH Ethernet Access Switch

P8ETH Spare (FPS0)

SFP
P8ETH Spare (FPS1)
SFP
FPGA 25 MHz CSM Act & Stby
SFP
ISPB
SFP
Backplane

Control
SerDes
Bus

CSM Main
RJ45 Giga
CSM Spare
XSwitch
RJ45
Ethernet
RJ45 Switch P8ETH Spare (FPS0)

RJ45 P8ETH Spare (FPS1)

950-0191-1
062410

P8ETH ethernet access switch card 3-57

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-107

3-58 P8ETH ethernet access switch card

UDS-108 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-108
ODU300 outdoor unit
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
ODU300, L6 GHz, 252.04 MHz SEPARATION
3DB23215AA ODU300, 5930 - 6020 MHZ, N/A N/A N/A Inactive
HP, TX LOW
3DB23215AD ODU300, 6182 - 6272 MHZ, N/A N/A N/A Inactive
HP, TX HIGH
3DB23215AB ODU300, 5989 - 6079 MHZ, N/A N/A N/A Inactive
HP, TX LOW
3DB23215AE ODU300, 6241 - 6331 MHZ, N/A N/A N/A Inactive
HP, TX HIGH
3DB23215AC ODU300, 6078 - 6168 MHZ, N/A N/A N/A Inactive
HP, TX LOW
3DB23215AF ODU300, 6330 - 6420 MHZ N/A N/A N/A Inactive
HP, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1, L6 GHz, 252.04 MHz SEPARATION
3DB23215HA ODU300, 5930 - 6020 MHZ, CRMLT10HRB 461514 213567 Active
HP, TX LOW
3DB23215HD ODU300, 6182 - 6272 MHZ, CRMLU10HRB 461515 213568 Active
HP, TX HIGH
3DB23215HB ODU300, 5989 - 6079 MHZ, CRMLV10HRB 461516 213569 Active
HP, TX LOW
3DB23215HE ODU300, 6241 - 6331 MHZ, CRMLW10HRB 461517 213570 Active
HP, TX HIGH
3DB23215HC ODU300, 6078 - 6168 MHZ, CRMLX10HRB 461518 213571 Active
HP, TX LOW
3DB23215HF ODU300, 6330 - 6420 MHZ CRMLY10HRB 461519 213572 Active
HP, TX HIGH
ODU300, U6 GHz, 160 MHz SEPARATION
3DB23214AA ODU300, 6540 - 6610 MHZ, N/A N/A N/A Inactive
HP, TX LOW
3DB23214AB ODU300, 6710 - 6780 MHZ, N/A N/A N/A Inactive
HP, TX HIGH
3DB23214AC ODU300, 6590 - 6660 MHZ, N/A N/A N/A Inactive
HP, TX LOW
3DB23214AD ODU300, 6760 - 6830 MHZ, N/A N/A N/A Inactive
HP, TX HIGH

ODU300 outdoor unit 3-59

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-108

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
3DB23214AE ODU300, 6640 - 6710 MHZ, N/A N/A N/A Inactive
HP, TX LOW
3DB23214AF ODU300, 6800 - 6870 MHZ, N/A N/A N/A Inactive
HP, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1, U6 GHz, 160 MHz SEPARATION
3DB23214HA ODU300, 6540 - 6610 MHZ, CRMLZ10HRB 461520 213573 Active
HP, TX LOW
3DB23214HB ODU300, 6710 - 6780 MHZ, CRML110HRB 461521 213574 Active
HP, TX HIGH
3DB23214HC ODU300, 6590 - 6660 MHZ, CRML210HRB 461522 213575 Active
HP, TX LOW
3DB21214HD ODU300, 6760 - 6830 MHZ, CRML310HRB 461523 213576 Active
HP, TX HIGH
3DB23214HE ODU300, 6640 - 6710 MHZ, CRML410HRB 461524 213577 Active
HP, TX LOW
3DB23214HF ODU300, 6800 - 6870 MHZ, CRML510HRB 461525 213578 Active
HP, TX HIGH
ODU300, U6 GHz, 340 MHz SEPARATION
3DB23216AA ODU300, 6430 - 6590 MHz, N/A N/A N/A Inactive
HP TX LOW
3DB23216AB ODU300, 6770 - 6930 MHz, N/A N/A N/A Inactive
HP TX HIGH
3DB23216AC ODU300, 6515 - 6675 MHz, N/A N/A N/A Inactive
HP TX LOW
3DB23216AD ODU300, 6855 - 7015 MHz, N/A N/A N/A Inactive
HP TX HIGH
3DB23216AE ODU300, 6600 - 6760 MHz, N/A N/A N/A Inactive
HP TX LOW
3DB23216AF ODU300, 6940 - 7100 MHz, N/A N/A N/A Inactive
HP TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1, U6 GHz, 340 MHz SEPARATION
3DB23216HA ODU300, 6430 - 6590 MHz, CRML610HRB 461526 213579 Active
HP TX LOW
3DB23216HB ODU300, 6770 - 6930 MHz, CRML710HRB 461527 213580 Active
HP TX HIGH
3DB23216HC ODU300, 6515 - 6675 MHz, CRML810HRB 461528 213581 Active
HP TX LOW
3DB23216HD ODU300, 6855 - 7015 MHz, CRML910HRB 461529 213582 Active
HP TX HIGH

3-60 ODU300 outdoor unit

UDS-108 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
3DB23216HE ODU300, 6600 - 6760 MHz, CRMMA00ARB 461530 213583 Active
HP TX LOW
3DB23216HF ODU300, 6940 - 7100 MHz, CRMMB00ARB 461531 213605 Active
HP TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1, 7 GHz, 175 MHz SEPARATION
3DB23223HA ODU300, 7124 - 7185 MHz, N/A N/A N/A Active
HP, TX Low
3DB23224HA ODU300, 7299 - 7360 MHz, N/A N/A N/A Active
HP, TX High
3DB23225HA ODU300, 7157.5 - 7217.5 N/A N/A N/A Active
MHz, HP, TX Low
3DB23226HA ODU300, 7332.5 - 7392.5 N/A N/A N/A Active
MHz, HP, TX High
3DB23227HA ODU300, 7190 - 7250 MHz, N/A N/A N/A Active
HP, TX Low
3DB23228HA ODU300, 7365 - 7425 MHz, N/A N/A N/A Active
HP, TX High
ODU300 W/LIGHTNING SURGE SUPPRESSOR1, 7 GHz, 150 MHz SEPARATION
3DB23217HA ODU300, 7424 - 7485 MHz, N/A N/A N/A Active
HP, TX Low
3DB23218HA ODU300, 7574 - 7635 MHz, N/A N/A N/A Active
HP, TX High
3DB23219HA ODU300, 7470 - 7530 MHz, N/A N/A N/A Active
HP, TX Low
3DB23220HA ODU300, 7620 - 7680 MHz, N/A N/A N/A Active
HP, TX High
3DB23221HA ODU300, 7515 - 7575 MHz, N/A N/A N/A Active
HP, TX Low
3DB23222HA ODU300, 7665 - 7725 MHz, N/A N/A N/A Active
HP, TX High
ODU300 W/LIGHTNING SURGE SUPPRESSOR1, 8 GHz, 300 MHz SEPARATION
3DB23033HA ODU300, 7722.5 - 7859 N/A N/A N/A Active
MHz, HP, TX Low
3DB23033HC ODU300, 8025 - 8171 MHz, N/A N/A N/A Active
HP, TX High
3DB23033HB ODU300, 7844 - 7981 MHz, N/A N/A N/A Active
HP, TX Low
3DB23033HD ODU300, 8145 - 8287 MHz, N/A N/A N/A Active
HP, TX High

ODU300 outdoor unit 3-61

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-108

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
ODU300 11 GHz, 590-490 MHz SEPARATION
3DB23035AA ODU300, 10675 - 10835 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23035AE ODU300, 11200 - 11345 N/A N/A N/A Inactive
MHZ, TX HIGH
3DB23035AB ODU300, 10795 - 10955 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23035AF ODU300, 11310 - 11465 N/A N/A N/A Inactive
MHZ, TX HIGH
3DB23035AC ODU300, 10915 - 11075 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23035AG ODU300, 11430 - 11585 N/A N/A N/A Inactive
MHZ, TX HIGH
3DB23035AD ODU300, 11035 - 11200 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23035AH ODU300, 11550 - 11705 N/A N/A N/A Inactive
MHZ, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1 11 GHz, 590-490 MHz SEPARATION
3DB23035HA ODU300, 10675 - 10835 CRMMC00ARB 213584 461532 Active
MHZ, TX LOW
3DB23035HE ODU300, 11200 - 11345 CRMMD00ARB 213585 461533 Active
MHZ, TX HIGH
3DB23035HB ODU300, 10795 - 10955 CRMME00ARB 461534 213586 Active
MHZ, TX LOW
3DB23035HF ODU300, 11310 - 11465 CRMMF00ARB 461536 213587 Active
MHZ, TX HIGH
3DB23035HC ODU300, 10915 - 11075 CRMMG00ARB 461537 213588 Active
MHZ, TX LOW
3DB23035HG ODU300, 11430 - 11585 CRMMH00ARB 461539 213589 Active
MHZ, TX HIGH
3DB23035HD ODU300, 11035 - 11200 CRMMJ00ARB 461540 213590 Active
MHZ, TX LOW
3DB23035HH ODU300, 11550 - 11705 CRMMK00ARB 461541 213591 Active
MHZ, TX HIGH
ODU300 15 GHz, 475/490 MHz SEPARATION
3DB23039AC ODU300, 14500 - 14660 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23039AD ODU300, 14975 - 15135 N/A N/A N/A Inactive
MHZ, TX HIGH

3-62 ODU300 outdoor unit

UDS-108 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
ODU300 W/LIGHTNING SURGE SUPPRESSOR1 15 GHz, 475/490 MHz SEPARATION
3DB23039HC ODU300, 14500 - 14660 N/A N/A N/A Active
MHZ, TX LOW
3DB23039HD ODU300, 14975 - 15135 N/A N/A N/A Active
MHZ, TX HIGH
ODU300 18 GHz, 340 MHz SEPARATION
3DB23041AA ODU300, 18580 - 18660 N/A N/A N/A Active
MHZ, TX LOW
3DB23041AB ODU300, 18660 - 18740 N/A N/A N/A Active
MHZ, TX LOW
3DB23041AC ODU300, 18740 - 18820 N/A N/A N/A Active
MHZ, TX LOW
3DB23041AD ODU300, 18920 - 19000 N/A N/A N/A Active
MHZ, TX HIGH
3DB23041AE ODU300, 19000 - 19080 N/A N/A N/A Active
MHZ, TX HIGH
3DB23041AF ODU300, 19080 - 19160 N/A N/A N/A Active
MHZ, TX HIGH
ODU300 18 GHz, 1008/1010/1092/1120 MHz SEPARATION
3DB23042AA ODU300, 17700 - 18060 N/A N/A N/A Active
MHZ, TX LOW
3DB23042AB ODU300, 17905 - 18275 N/A N/A N/A Active
MHZ, TX LOW
3DB23042AC ODU300, 18110 - 18490 N/A N/A N/A Active
MHZ, TX LOW
3DB23042AD ODU300, 18330 - 18690 N/A N/A N/A Active
MHZ, TX LOW
3DB23042AE ODU300, 18710 - 19070 N/A N/A N/A Active
MHZ, TX HIGH
3DB23042AF ODU300, 18920 - 19290 N/A N/A N/A Active
MHZ, TX HIGH
3DB23042AG ODU300, 19130-19510 N/A N/A N/A Active
MHZ, TX HIGH
3DB23042AH ODU300, 19340 - 19700 N/A N/A N/A Active
MHZ, TX HIGH
ODU300 18 GHz, 1560 MHz SEPARATION
3DB23062AC ODU300, 17700 - 18060 N/A N/A N/A Inactive
MHZ, TX LOW

ODU300 outdoor unit 3-63

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-108

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
3DB23062AD ODU300, 19260 - 19620 N/A N/A N/A Inactive
MHZ, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1 18 GHz, 1560 MHz SEPARATION
3DB23062HC ODU300, 17700 - 18060 CRMML00ARB 461542 213592 Active
MHZ, TX LOW
3DB23062HD ODU300, 19260 - 19620 CRMMM00ARB 461543 213593 Active
MHZ, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1 18 GHz, 1560 MHz SEPARATION, HIGH POWER
3DB23062HE ODU300, 17700 - 18140 N/A N/A N/A Active
MHZ, TX LOW, HP
3DB23062HF ODU300, 19260 - 19700 N/A N/A N/A Active
MHZ, TX HIGH, HP
ODU300 23 GHz, 1200 MHz SEPARATION
3DB23045AA ODU300, 21200 - 21570 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23045AE ODU300, 22400 - 22770 N/A N/A N/A Inactive
MHZ, TX HIGH
3DB23045AB ODU300, 21475 - 21845 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23045AF ODU300, 22675 - 23045 N/A N/A N/A Inactive
MHZ, TX HIGH
3DB23045AC ODU300, 21750 - 22120 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23045AG ODU300, 22950 - 23320 N/A N/A N/A Inactive
MHZ, TX HIGH
3DB23045AD ODU300, 22030 - 22400 N/A N/A N/A Inactive
MHZ, TX LOW
3DB23045AH ODU300, 23230 - 23600 N/A N/A N/A Inactive
MHZ, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1 23 GHz, 1200 MHz SEPARATION
3DB23045HA ODU300, 21200 - 21570 CRMMN00ARB 461544 213594 Active
MHZ, TX LOW
3DB23045HE ODU300, 22400 - 22770 CRMMP00ARB 461548 213595 Active
MHZ, TX HIGH
3DB23045HB ODU300, 21475 - 21845 CRMMR00ARB 461545 213596 Active
MHZ, TX LOW
3DB23045HF ODU300, 22675 - 23045 CRMMS00ARB 461549 213597 Active
MHZ, TX HIGH

3-64 ODU300 outdoor unit

UDS-108 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
3DB23045HC ODU300, 21750 - 22120 CRMMT00ARB 461546 213598 Active
MHZ, TX LOW
3DB23045HG ODU300, 22950 - 23320 CRMMU00ARB 461550 213599 Active
MHZ, TX HIGH
3DB23045HD ODU300, 22030 - 22400 CRMMV00ARB 461547 213600 Active
MHZ, TX LOW
3DB23045HH ODU300, 23230 - 23600 CRMMW00ARB 461551 213601 Active
MHZ, TX HIGH
ODU300 W/LIGHTNING SURGE SUPPRESSOR1 23 GHz, 1200 MHz SEPARATION, HIGH POWER
3DB23045HI ODU300, 21200 - 21570 N/A N/A N/A Active
MHZ, TX LOW, HP
3DB23045HM ODU300, 22400 - 22770 N/A N/A N/A Active
MHZ, TX HIGH, HP
3DB23045HJ ODU300, 21475 - 21845 N/A N/A N/A Active
MHZ, TX LOW, HP
3DB23045HN ODU300, 22675 - 23045 N/A N/A N/A Active
MHZ, TX HIGH, HP
3DB23045HK ODU300, 21750 - 22120 N/A N/A N/A Active
MHZ, TX LOW, HP
3DB23045HO ODU300, 22950 - 23320 N/A N/A N/A Active
MHZ, TX HIGH, HP
3DB23045HL ODU300, 22030 - 22400 N/A N/A N/A Active
MHZ, TX LOW, HP
3DB23045HP ODU300, 23230 - 23600 N/A N/A N/A Active
MHZ, TX HIGH, HP
ODU300 W/LIGHTNING SURGE SUPPRESSOR 38 GHz, 700 MHz SEPARATION
3DB23258HO ODU300, 38600 - 38800 N/A N/A N/A Active
MHZ, TX LOW
3DB23258HP ODU300, 39300 - 39500 N/A N/A N/A Active
MHZ, TX HIGH
3DB23258HQ ODU300, 38750 - 38950 N/A N/A N/A Active
MHZ, TX LOW
3DB23258HR ODU300, 39450 - 39650 N/A N/A N/A Active
MHZ, TX HIGH
3DB23258HS ODU300, 38950 - 39150 N/A N/A N/A Active
MHZ, TX LOW

ODU300 outdoor unit 3-65

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-108

PART NUMBER/ NAME CLEI ECI/ CPR STATUS

MNEMONIC BAR CODE
3DB23258HT ODU300, 39650 - 39850 N/A N/A N/A Active
MHZ, TX HIGH
3DB23258HU ODU300, 39100 - 39300 N/A N/A N/A Active
MHZ, TX LOW
3DB23258HV ODU300, 39800 - 40000 N/A N/A N/A Active
MHZ, TX HIGH
[1] ODU300’s with Lightning Surge Suppressor are supported starting with 9500 MPR-A R1.2.x and are not sup-
ported by R1.0.x and R1.1.x.

3-66 ODU300 outdoor unit

UDS-108 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Features and application notes

• Optimal for urban links

• ODU300s are band specific

• Supports static and adaptive modulation

• Support for the following channel plans: Lower 6 GHz, Upper 6 GHz,
7 GHz, 8 GHz, 11 GHz, 15 GHz, 18 GHz, and 23 GHz.

• Channel frequency software selectable within tuning range of the

ODU300

• Support for the following static radio profiles:

– Supported static channel bandwidths: 10, 30, 40, and 50 MHz

– Supported static modulations: 4 QAM, 16 QAM, 32 QAM,

64 QAM, 128 QAM, and 256 QAM

• Support for the following adaptive radio profiles:

– Supported adaptive channel bandwidth: 30 MHz

– Supported adaptive modulations: 4/16 QAM, 4/16/64 QAM,

4/16/64/128 QAM and 4/16/64/128/256 QAM

• Automatic Transmit Power Control (ATPC) support

• Integrated antenna mount

• Non-Integrated antenna mount optional

• Polarization is field configurable, Vertical (standard) or horizontal

(optional)

• Coaxial connection to the MSS/MOD300 card

• ODU300s available with built-in lightning surge suppressor

Description

The ODU300 is a microprocessor controlled transceiver that interfaces the

MSS-4/8 shelf MOD300 card with the antenna. Transmitter circuits in the
ODU300 consists of cable interface, modulator, local oscillator, up
converter/mixer, power amplifier, and diplexer. Receive circuits consist of

ODU300 outdoor unit 3-67

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-108

diplexer, low-noise amplifier, local oscillator, down converter/mixer, automatic

gain control, and cable interface. The microprocessor manages ODU300
frequency, transmit power alarming, and performance monitoring. Power is
provided by -48Vdc from the MSS to the ODU300 DC-DC converter. The
ODU300 is frequency dependent.

Indicators, connectors, and control

See Figure 108-1 for ODU300 configured in integrated antenna mount

configuration. See Figure 108-2 for ODU300s configured in HSB coupler mount
configuration.

The ODU300 has no indicators and controls on the unit.

Refer to Table 108-A for ODU300 connector details.

The MOD300 card has no controls located on the card.

Figure 108-1. ODU300 and antenna, integrated mount configuration

Figure 108-2. ODU300 and antenna, integrated mount with HSB coupler

3-68 ODU300 outdoor unit

UDS-108 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 108-A. Core-E front panel connector details

CONNECTOR TYPE FUNCTION
Antenna Port Waveguide RF signal to antenna
Interface
IF Signal In Type-N Female IF signal from MOD300 card
RSSI BNC Female RSSI Monitor Port
Ground Stud ODU300 Grounding

RSSI monitoring point

The ODU300 has a capped BNC female connector to access RSSI during
antenna alignment.

There is a linear relationship of voltage to RSSI, as shown in the table below;

an RSSI of 0.25 Vdc is equivalent to -10 dBm RSSI, and each additional 0.25
Vdc RSSI increase thereafter corresponds to a 10 dBm decrease in RSSI.

The lower the voltage the higher RSSI and better aligned the antenna is.

Table 108-C. RSSI table

UNITS MEASUREMENT
BNC (Vdc) 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 2.25 2.5
RSSI (dBm) -10 -20 -30 -40 -50 -60 -70 -80 -90 -100

Waveguide flange data

Table 108-D lists the antenna port flange types used with the ODU300, plus
their mating flange options and fastening hardware for remote mount
installations.

UDR/PDR flanges are rectangular; UBR/PDR flanges are square.

On the ODU300, the two flange styles are:

• UDR. 6-hole or 8-hole (6/8 bolt holes depending on frequency

range/waveguide type), flush-face flange with threaded, blind holes.

• UBR. 4-hole flush-face flange with threaded, blind holes.

ODU300 outdoor unit 3-69

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-108

The corresponding mating flange styles are:

• PDR. 6-hole or 8-hole flange with gasket groove and clear holes.

• PBR. 4-hole flange with a gasket groove and clear holes.

All fastening hardware is metric.

Table 108-D. ODU300 waveguide flange data

FREQ RADIO WAVE- WAVE- SPRING BOLTS BOLT THREAD HOLE BOLT LENGTH
BAND FLANGE GUIDE GUIDE WASHERS REQD TYPE SPEC DEPTH REQUIRED
MATING TYPE REQD mm
FLANGE
6 GHz UDR70 PDR70 WR137 8 x M5 8 M5x0. 6H 10 Flange
8 thickness +
Hole depth -
2mm
7/8 UDR84 PDR84 WR112 8 x M4 8 M4x0. 6H 8 Flange
GHz 7 thickness +
Hole depth -
2mm
10/11 UDR100 PDR100 WR90 8 x M4 8 M4x0. 6H 8 Flange
GHz 7 thickness +
Hole depth -
2mm
13 UBR120 PBR120 WR75 4 x M4 4 M4x0. 6H 8 Flange
GHz 7 thickness +
Hole depth -
2mm
15 UBR140 PBR140 WR62 4 x M4 4 M4x0. 6H 8 Flange
GHz 7 thickness +
Hole depth -
2mm
18/23/ UBR220 PBR220 WR42 4 x M3 4 M3x0. 6H 6 Flange
26 5 thickness +
GHz Hole depth -
2mm
28/32/ UBR320 PBR320 WR28 4 x M3 4 M3x0. 6H 6 Flange
38 5 thickness +
GHz Hole depth -
2mm

3-70 ODU300 outdoor unit

UDS-109 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-109
MPT-HL transceiver
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3EM22617AA MPT-HL Transceiver L6, CRTUAAXFAA 171610 070VLL Active
5725-6425 MHz
3EM22617AB MPT-HL Transceiver U6, CRTUAAYFAA 171611 070VLM Active
6425-6930 MHz
3EM22617AC MPT-HL Transceiver L6, CRTUABLFAA 173789 070XRS Active
5925-6425 MHz, HP
3EM22617AD MPT-HL Transceiver U6, CRTUABMFAA 173790 070XRS Active
6425-6930 MHz, HP
3EM24627AA MPT-HL Transceiver 7, N/A N/A N/A Active
7125-7775 MHz
3EM24627AB MPT-HL Transceiver 8, N/A N/A N/A Active
7725-8500 MHz
3EM23888AA MPT-HL Transceiver 10.5, CRTUABPCAA 174725 070YGX Active
10400-10700 MHz
3EM23888AB MPT-HL Transceiver 11, CRTUABRCAA 174727 070YGY Active
10700-11200 MHz
3EM23888AC MPT-HL Transceiver 11, CRTUABSCAA 174728 070YGZ Active
11200-11700 MHz

MPT-HL transceiver 3-69

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-109

Features and application notes

• High-capacity, long-haul RF transmission shelf

• Support for the following RF configurations: Non-Standby, Hot

Standby, Space Diversity, and Frequency Diversity

• Support for the following channel plans: 5.8 GHz Unlicensed, Lower 6
GHz, Upper 6 GHz, 7 GHz, 8 Ghz, 10.5 GHz, and 11 GHz

• Support for the following static radio profiles:

– Supported static channel bandwidths: 5, 10, 30, and 40 MHz

– Supported static modulations: 32 QAM, 128 QAM, and 256 QAM

• Support for the following adaptive radio profiles:

– Supported adaptive channel bandwidths: 30 MHz

– Supported adaptive modulations: 4/16/64/128/256 QAM

• Automatic Transmit Power Control (ATPC) support

• Gigabit Ethernet connection to 9500 MPR-A MSS indoor unit using

standard SFPs

Table 109-A. MPT-HL static modulation profiles (standard gain)

CHANNEL SIZE 5 10 30 40
FIXED MODULATION 32 128 32 128 32 128 256 128 256
FREQUENCY
UNLICENSED 5.8 GHZ N Y Y Y Y Y Y N N
LOWER 6 GHZ N Y N Y N Y Y N N
UPPER 6 GHZ N Y N Y N Y Y N N
7/8 GHZ Y Y Y Y Y Y Y N N
10.5 GHZ N Y N N N N N N N
11 GHZ Y Y Y Y Y Y Y Y Y

3-70 MPT-HL transceiver

UDS-109 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 109-B. MPT-HL static modulation profiles (maximum system gain)

CHANNEL SIZE 5 10 30 40
FIXED MODULATION 32 128 32 128 32 128 256 128 256
FREQUENCY
UNLICENSED 5.8 GHZ N N N N N N N N N
LOWER 6 GHZ N N N N N Y Y N N
UPPER 6 GHZ N N N N N Y Y N N
7/8 GHZ N N N N N Y Y N N
10.5 GHZ N N N N N N N N N
11 GHZ N N N N N Y Y N N

Table 109-C. MPT-HL adaptive modulation profiles

CHANNEL SIZE 30
FIXED MODULATION 4 16 64 128 256
FREQUENCY
UNLICENSED 5.8 GHZ Y Y Y Y Y
LOWER 6 GHZ Y Y Y Y Y
UPPER 6 GHZ Y Y Y Y Y
7/8 GHZ Y Y Y Y Y
10.5 GHZ N N N N N
11 GHZ Y Y Y Y Y

Description

The MPT-HL Transceiver card is a microprocessor controlled RF transceiver

that interfaces the MSS-8 shelf P8ETH card MPT-HL port with the antenna.
The MPT-HL Transceiver microprocessor manages transmit and receive
frequencies, transmit power, alarming, and performance monitoring.

There are no MPT-HL Transceiver card options. The MPT-HL Transceiver

resides in the MPT-HL shelf. Supported configurations are one or two
Non-Standby (1+0) radios, Hot Standby (1+1) and Hot Standby space and
frequency diversity.

MPT-HL transceiver 3-71

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-109

Indicators, connectors, and control

The MPT-HL Transceiver card has the following indicators, connectors, and
controls.

See Figure 109-1 for MPT-HL Transceiver card front panel indicator and
connector locations.

Refer to Table 109-D for MPT-HL Transceiver card indicators details.

Refer to Table 109-E for MPT-HL Transceiver card connector details.

Refer to Table 109-F for MPT-HL Transceiver card control details.

3-72 MPT-HL transceiver

UDS-109 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 109-1. MPT-HL transceiver

MPT-HL transceiver 3-73

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-109

Table 109-D. MPT-HL transceiver front panel indicator details

INDICATOR STATUS DEFINITION
Status (S) Off Card not equipped, not provisioned, or not powered
Green Blinking Configuration Downloading, or SW Booting. (Different
blink rates should be used to identify each step of the
startup process.)
Green In Service, Normal Operation, and Properly Provisioned.
EPS or RPS currently In-Service/Active.
Yellow In Protect, Properly Provisioned. EPS and RPS currently
in Standby.
Green/Red Card Properly Equipped and Provisioned. Either TX or RX
Blinking equipment or signal Fault. EPS or RPS currently
In-Service/Active. Traffic is probable affected.
Yellow/Red Card Properly Equipped and Provisioned, TX or RX signal
Blinking Fault, EPS and RPS currently in Standby. Traffic maybe
affected.
Red Card Fail
Red Blinking MAP Communication Time-out: Communication between
the MPT-HL Transceiver and the P8ETH cards is lost.
Power Emission Off MPT-HL Transceiver is not emitting power for reasons
other than “forced squelch”.
1. Transmit Protection Switch (TPS) is currently in
standby state.
2. Software booting or FPGA download in progress
Green Blinking MPT-HL Transceiver is not emitting power due to a forced
squelch condition.
1. TX mute active
2. PA switch is positioned Off
Green MPT-HL Transceiver is emitting power as expected
according to the known configuration.
Link (L) Off Link Down
On Link Up
Activity (A) Off No Tx/Rx activity
Blinking Tx/Rx activity

Table 109-E. MPT-HL transceiver front panel connector details

CONNECTOR TYPE FUNCTION
Battery Power D-SUB MPT-HL Transceiver Power Input
SFP Port SFP Communication link with the P8ETH card
Craft Terminal/CT RJ45 Not supported in this release.

3-74 MPT-HL transceiver

UDS-109 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 109-F. MPT-HL transceiver front panel control details

CONTROL POSITION FUNCTION
PA 0 Transmit OFF (TxMute)
1 Transmit ON

Functional overview

In the TX direction, the MPT-HL Transceiver converts Ethernet packet data

from the P8ETH (Ethernet Access Switch - EAS) card MPT-HL port into a
modulated IF output signal. The modulated IF signal is converted into a RF
signal which is amplified by the Power Amplifier (PA) and routed through a
band-pass filter to the antenna.

In the RX direction, the MPT-HL Transceiver card amplifies the incoming RF

signal. Converts the RF signal into a first IF signal. The first IF signal is then
converted to a second IF signal. The second IF signal is filtered, demodulated,
and converted into Ethernet packet data. The Ethernet packet data is then
sent to the P8ETH card MPT-HL port.

See figure 109-2 for a block diagram of the MPT-HL Transceiver.

Figure 109-2. MPT-HL transceiver block diagram

MPT Transceiver Card

Modem RF Transceiver

SFP I I
MODEM Bias Tx RF
Board Q Board Q
PA Back
RJ45 Plane
I2C I2C Antenna
RF Port
Transceiver
Board
+/-20V
+/-60V PSU IF IF Rx

DC Voltages

950-0192-1
062410

MPT-HL transceiver 3-75

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-109

3-76 MPT-HL transceiver

UDS-110 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-110
Fan cards
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3DB18134BA Fan 2U Card N/A N/A N/A Active
3DB18134BB Fan 2U Card CRCCACPJAA 171275 070VGP Active
3EM23911AA Fan 2U Card W/Alarms CRCCADYJAA 172825 070XBK Active
3DB18218AD Fan 1U Card N/A-4 N/A-4 N/A-4 Active-4

Features and application notes

• Provides forced air flow for MSS-8 or MSS-4 shelf cooling.

• Fan 2U card types are used in MSS-8 shelf application. Two fan types
are available:

– Fan 2U card (Basic fan card)

– FAN 2U card W/Alarms (Enhanced) provides relay alarm support

• Enhanced FAN provides Summary, major, and Minor alarm front

panel LEDs and alarm relay outputs

• Fan 1U card is used in MSS-4 shelf application.

Description

Both the basic and enhanced Fan 2U cards provide forced air cooling for the
MSS-8 shelf.

Enhanced Fan 2U card provides up to four alarm input signals to the MSS-8
shelf and up to three alarm outputs.

Indicators, connectors, and control

The Fan 1U card has no indicators, connectors and controls.

The basic Fan 2U card has no indicators, connectors and controls.

Fan cards 3-77

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-110

See Figure 110-1 for enhanced Fan 2U card with alarms front panel indicator,
controls, and connector locations.

Refer to Table 110-A for enhanced Fan 2U card indicators details.

Refer to Table 110-B for Fan 2U card connector details.

Refer to Table 110-C for Fan 2U card control details.

Alarm inputs 1, 2, 3, and 4, Alarm Cutoff, and Lamp Test are not supported
with R4.1.0 software.

Figure 110-1. Fan 2U card w/alarms (front view)

950-0110-1
011210

3-78 Fan cards

UDS-110 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 110-A. FAN 2U w/alarms front panel indicator details

INDICATOR STATUS DEFINITION
Fan Off LED not supported in this release.
Batt A Green LED not supported in this release.
Batt B Green LED not supported in this release.
Summary On NE summary alarm indicates either a Major or Minor
alarm.
Major Red NE summary, indicates a Major alarm is present.
Minor Yellows NE summary, indicates a Minor alarm is present.

Table 110-B. FAN 2U w/alarms front panel connector details

CONNECTOR TYPE FUNCTION
External Alarms DSUB 15 External Alarm Inputs and Outputs
Position

Table 110-C. FAN 2U w/alarms front panel control details

CONNECTOR TYPE FUNCTION
ACO/LT1 push button Alarm cutoff

[1] ACO/LT control is not supported in R4.1.0 software.

Fan cards 3-79

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-110

Table 110-D. Fan 2U card office alarm and control connector / cable detail
PIN DEFINITION Function CONTACT NUMBER WIRE COLOR
Alarm Input 11 01 White/Blue

Alarm Input 21 02 Blue/White

Alarm Input 31 11 White/Orange

Alarm Input 41 12 Orange/White

Ground 07 White/Green
Alarm Output 1 14 White/Brown
Summary Alarm
Alarm Output 1 15 Brown/White
Alarm Output 2 08 White/Slate
Major Alarm
Alarm Output 2 10 Slate/White
Alarm Output 3 04 Red/Blue
Minor Alarm
Alarm Output 3 05 Blue/Red
Not Used 03 N/A
Not Used 06 N/A
Not Used 09 N/A
Not Used 13 N/A
[1] Alarm inputs 1, 2, 3, and 4 are not supported with R4.1.0 software.

Functional overview

Both the basic and enhanced Fan 2U cards provide forced air cooling for the
MSS-8 shelf.

The Fan 1U card provide forced air cooling for the MSS-4 shelf.

The enhanced Fan 2U card alarm outputs are floating optical relays. Alarm
output 1 is a normally closed relay rated for 350 V and 120 mA. Alarm outputs
2 and 3 are normally open relays rated for 350 V and 100 mA. Alarm outputs
are used in pairs with an appropriate sized pull-up resistor on either pin
(floating).

Alarm output 1 (Summary Alarm) is energized for the no-alarm state, so that
it generates an alarm when shelf power is lost. As a result, all outputs are open
during system operation with no alarms.

The enhanced Fan 2U card alarm inputs 1, 2, 3, and 4, Alarm Cutoff, and Lamp
Test are not supported with R4.1.0 software.

3-80 Fan cards

UDS-111 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-111
GigE SFP
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3EM20277AA GigE SFP 1000Base-SX, DRR3AA3CAA 147527 U73234 Active
850 nm
3EM20277AB GigE SFP 1000Base-LX, DRR3AA4CAA 147539 U73235 Active
1310 nm
3EM20277AC GigE SFP 1000Base-EX, DRR3AA5CAA 147542 U73236 Active
1310 nm
3EM20277AD GigE SFP 1000Base-ZX, DRR3AA6CAA 147544 U73237 Active
1550 nm

Features and application notes

• Is an in-service pluggable optical card

• Provides a 1.25 Gb/s Gigabit Ethernet (GigE) interface for Control and
Switching Module (Core-E) or Ethernet Access Switch Card (P8ETH).

• Available in four optical reaches

– 1000Base-SX, 850 nm (up to 550 meter applications)

– 1000Base-LX, 1310 nm (up to 10 kilometer applications)

– 1000Base-EX, 1310 nm (up to 40 kilometer applications)

– 1000Base-ZX, 1550 nm (up to 80 kilometer applications)

• Provides a duplex LC connector

• Is compliant with Small Form Factor Plug-in (SFP) Multi-Service

Agreement (MSA)

Description

The GigE Small Form Factor Plug-in (SFP) is installed in one slot of a Core-E
or P8ETH. Provides a 1.25 Gb/s; 1000Base-SX 850 nm, 1000Base-LX 1310 nm,
1000Base-EX 1310 nm, or 1000Base-ZX 1550 nm GigE interface and a duplex
LC connector. See figure 111-1 for an illustration of the GigE SFPs.

GigE SFP 3-81

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-111

Indicators, connectors, and control

The GigE SFPs have the following indicators and connector.

Refer to Table 111-A for GigE SFP indicators details.

Refer to Table 111-B for GigE SFP connector details.

The GigE SFP has no controls located on the assembly.

Table 111-A. SFP indicator details

INDICATOR STATUS DEFINITION
LINK Off Indicates GigE link is down
Green Indicates GigE link is up
ACTIVITY Off Indicates no activity on GigE link
Amber Blinking Indicates activity on GigE link

Table 111-B. SFP connector details

CONNECTOR TYPE FUNCTION
DUPLEX OPTICAL LC Tx and Rx GigE ports
CONNECTOR

Functional overview

The GigE SFP interfaces with the Core-E or P8ETH through a 2.5 Gb/s data
signal line. All timing, control, and power are provided by the Core-E or P8ETH
in which it is housed (refer to UDS-103 or UDS-107, respectively, for
information). See figure 111-2 for a block diagram of the GigE SFPs.

3-82 GigE SFP

UDS-111 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 111-1. Optical SFP module

Transceiver CSM SFP module

Transceiver EAS SFP module

Output

Input

Optical cables

950-0001-1
072009

On the transmitter side, the GigE SFPs has an automatic optical output power
control circuit, a laser driver and a laser diode module. The transmitter is
based on a non-cooled DFB laser. The laser safety class for the complete
integrated module is class 1 according to IEC 60825. It can manage commands
for TX disable and provides a TX fault alarm.

TX fault indicates a laser fault. The transmitter is not disabled when the TX
fault signal is active. TX disable is an input that is used to shut down the
transmitter optical output.

On the receiver side, the GigE SFPs have a PIN photo detector for light-to-
electrical current conversion and a limiting amplifier. The photo-detected
current is amplified by an electrical circuit that delivers two complementary
data signals.

GigE SFP 3-83

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-111

Figure 111-2. Optical SFP module block diagram

SFP MODULE HOST MODULE

MONITOR TD+
LD
PIN PD LASER
DRIVER 100 7 TD-

VccT VccT
4.7 k7 4.7 k7 TO
TX DISABLE 10 k7
AUTOMATIC
POWER CONTROL
TX FAULT
CIRCUIT

(A) TRANSMITTER

PIN PD
RD+
PRE- POST-
AMP AMP 100 7
RD-

VccR
4.7 k7 TO
LOS 10 k7

(B) RECEIVER

TEMPERATURE VccT
SUPPLY VOLTAGE DIAGNOSTIC
TX BIAS CURRENT MONITOR
TX OUTPUT POWER 4.7 k7 TO
RX RECEIVED POWER 10 k7
MOD-DEF (0)

MOD-DEF (1)
EEPROM
MOD-DEF (2)

100 7

(C) EEPROM
950-0002-1
072009

The module provides LOS alarm (loss of input power signal alarm). This output
signal indicates the received optical power is below the worst-case receiver
sensitivity (as defined by the standard in use).

The transceiver has an EEPROM to provide Remote Inventory RI information.

DDM supports analog parameter measurements such as temperature, laser
bias, and laser power.

3-84 GigE SFP

UDS-112 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-112
Power distribution unit (PDU)
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
3EM13317AA PDU Power Distribution N/A N/A N/A Active
Unit

Features and application notes

• Distributes A and B battery power that feeds MSS-8 and/or MPT-HL

shelves and/or auxiliary equipment

• Provides fused protection for individual shelves and auxiliary

equipment

• Floating Battery inputs to support both ±24 and ±48 VDC operation

• Optional relay card that provides eight Form-C outputs

• Mounts in a 19-inch aluminum rack or 19-inch seismic rack. Adapter

flanges available to mount in a 23-inch aluminum rack

• Requires 5.25 inches (3 EIA rack increments) of open rack space

Description

The PDU provides redundant, fuse protected connections to up to six

9500 MPR-A shelves and/or auxiliary equipment. Two isolated battery input
connections (A & B). Each battery input is distributed to six alarm indicating
fused battery outputs (A+/A- & B+/B-) See Figure 112-1 for an isometric view
of the PDU. See Figure 112-2 for a front panel view of the PDU.

Power distribution unit (PDU) 3-85

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-112

Figure 112-1. Power distribution unit (PDU) isometric view

BATTERY INPUT
WIRE SIZE No. 4 (Max)

POWER DISTRIBUTION UNIT

ISOMETRIC VIEW - CIRCUIT BOARD
AND FRONT PANEL REMOVED

A+ A- B+ B-
Battery Battery Front View Fuse Battery Battery

950-0112-1
071610

3-86 Power distribution unit (PDU)

UDS-112 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Figure 112-2. Power distribution unit (PDU) front panel view

A+ A- B+ B-
Battery Battery Front View Fuse Battery Battery

950-0113-1
071610

Indicators, connectors, and control

The PDU card has the following indicators, connectors, and controls.

See Figure 112-3 for PDU card front panel indicator and connector locations.

The PDU has fuse summary alarm indicator.

Refer to Table 112-A for PDU connector details.

Figure 112-3. PDU indicator and connector locations

B Ground
A+ A- Straps and B+ B-
Battery Battery Front View Fuse Common Battery Battery

A Ground
A Battery Ground Outputs B Battery Ground Outputs
Straps and
Fused - A Battery Outputs Fused + B Battery Outputs
Common
Fused + A Battery Outputs Fused - B Battery Outputs
950-0114-1
071610

Power distribution unit (PDU) 3-87

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-112

Table 112-A. PDU connector details

CONNECTOR DESIGNATOR TYPE FUNCTION
A+ TB1 One-Hole, A Battery positive battery input
A- TB2 0.250 inch, A Battery negative battery input
compression lug
B+ TB3 B Battery positive battery input
B- TB4 B Battery negative battery input
FA1+ E1 Fused A1 battery positive output
FA2+ E2 Fused A2 battery positive output
FA3+ E3 Fused A3 battery positive output
FA4+ E4 Fused A4 battery positive output
FA5+ E5 Fused A5 battery positive output
FA6+ E6 Fused A6 battery positive output
FA1- E7 Fused A1 battery negative output
FA2- E8 Fused A2 battery negative output
FA3- E9 Fused A3 battery negative output
FA4- E10 Fused A4 battery negative output
FA5- E11 Fused A5 battery negative output
FA6- E12 Fused A6 battery negative output
FB1+ E13 Fused B1 battery positive output
FB2+ E14 Fused B2 battery positive output
FB3+ E15 Fused B3 battery positive output
FB4+ E16 Fused B4 battery positive output
FB5+ E17 Fused B5 battery positive output
FB6+ E18 Fused B6 battery positive output
FB1- E19 Fused B1 battery negative output
FB2- E20 Fused B2 battery negative output
FB3- E21 Fused B3 battery negative output
FB4- E22 Fused B4 battery negative output

3-88 Power distribution unit (PDU)

UDS-112 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

Table 112-A. PDU connector details

CONNECTOR DESIGNATOR TYPE FUNCTION
FB5- E23 Fused B5 battery negative output
FB6- E24 Fused B6 battery negative output
GND A1 E25 Ground A1 output
GND A2 E26 Ground A2 output
GND A3 E27 Ground A3 output
GND A4 E28 Ground A4 output
GND A5 E29 Ground A5 output
GND A6 E30 Ground A6 output
GND B1 E36 Ground B1 output
GND B2 E35 Ground B2 output
GND B3 E34 Ground B3 output
GND B4 E33 Ground B4 output
GND B5 E32 Ground B5 output
GND B6 E31 Ground B6 output
A- STR E37 A ground strap for positive voltage applications1
GND STR A E38 A ground common2
A+ STR E39 A ground strap for negative voltage
applications3
B- STR E40 B ground strap for positive voltage applications
GND STR B E41 B ground common
B+ STR E42 B ground strap for negative voltage applications
[1] Connector is used to configure PDU for floating rectifier positive battery voltage applications. Connect jumper
between A/B- Str and GND STR A/B.
[2] A/B ground common strap, connects to the A/B GND connectors on the PDU.
[3] Connector is used to configure PDU for floating rectifier negative battery voltage applications. Connect jumper
between A/B+ Str and GND STR A/B.

Functional overview

The PDU accepts two ±24 or ±48 V DC inputs and splits them into twelve
separate, fuse protected outputs. The input power interface consists of two
pairs of ±24 or ±48 V DC (A+/A- B+/-) connections. These connections are rated
at 60 amps each. The PDU splits each BATT connection into six separate
output connections. Both positive and negative outputs are protected by GMT
fuses, 20 amps maximum each. All fuses are accessible and replaceable from
the front panel. The electrical inputs are accessible from the top of the PDU.
The electrical output connections are accessible from the side and rear panel.

Power distribution unit (PDU) 3-89

3EM23952AL
Issue 0.1, November 2012 PRELIMINARY UDS-112

3-90 Power distribution unit (PDU)

UDS-113 PRELIMINARY 3EM23952AL
Issue 0.1, November 2012

UDS-113
DS1 RJ-45 Patch Panel
PART NUMBER/ NAME CLEI ECI/ CPR STATUS
MNEMONIC BAR CODE
1AF15245AB DS1 RJ-45 Patch Panel N/A N/A N/A Active

Features and application notes

• Converts P32E1DS1 card SCSI connectors to thirty-two RJ-45

connectors.

• Supports both protected and non-protected P32E1DS1 applications.

• Requires two 68 pin SCSI cables in non-protected DS1 configuration.

Requires four 68 pin SCSI cables in protected DS1 configuration.

Description

The DS1 RJ-45 Patch Panel mounts above and/or below the MSS-8 shelf.
Requires 1.5 rack increments.

Customer interconnect are thirty-two RJ-45 connectors, I/O 1 through I/O 32.
Each RJ-45 connector supports one DS1 signal, 1 through 32 respectively and
provides both input and output signal connections. Four 68 pin SCSI
connectors interconnects the main and spare P32E1DS1 card connectors. See
Figure 113-1 for a front view of the DS1 RJ-45 Patch Panel. See Figure 113-2
for a rear view of the DS1 RJ-45 Patch Panel.

Figure 113-1. DS1 RJ-45 patch panel (front view)

RJ-45 DS1 Patch Panel 950-0117-1

Front View 071710

DS1 RJ-45 Patch Panel 3-91