0% found this document useful (1 vote)

385 views253 pages

Inital Soil Report - Camella Lima - Malvar, Batangas - VERTEX Geotech - 06.22.2019

The document provides a geotechnical investigation report for a proposed two-storey residential development in Brgy. Santiago, Malvar, Batangas. The investigation included 8 test pits, 30 Mackintosh Probe Tests, and 30 Dynamic Cone Penetration Tests to analyze the soil conditions up to 2 meters below the surface. Soil samples were tested in a laboratory to determine properties. The preliminary conclusion is that the site's geology consists of silty clay and clay soils with varying depths and slopes. The investigation provides information on the soil conditions and parameters to evaluate foundation requirements and geotechnical considerations for the proposed development.

Uploaded by

Rex Camiro

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (1 vote)

385 views253 pages

Inital Soil Report - Camella Lima - Malvar, Batangas - VERTEX Geotech - 06.22.2019

Uploaded by

Rex Camiro

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 253

Upper Ground Floor, Worldwide Corporate Camella Cerritos, Molino IV,

Center Bacoor, Cavite

Shaw, Boulevard, 1552 Mandaluyong City, Contact No. (02) 226 3552
Metro Manila Local: 0566
Contact No. (02) 226 3552 Cellphone No.: 0917-626-9380
Local: 0566

GEOTECHNICAL INVESTIGATION

PROPOSED TWO-STOREY RESIDENTIAL DEVELOPMENT

CAMELLA LIMA
BRGY. SANTIAGO, MALVAR, BATANGAS

As Prepared for

As Prepared by

VERTEX Geotech Team

MAY 2019
Geotechnical Investigation of Two-storey Residential Development: Brgy. Santiago, Malvar, Batangas

GEOTECHNICAL INVESTIGATION REPORT

Subsurface Investigation for
PROPOSED TWO-STOREY
RESIDENTIAL DEVELOPMENT
BRGY. SANTIAGO, MALVAR, BATANGAS

TABLE OF CONTENTS

CONTENTS PAGE

1. INTRODUCTION

2. PURPOSE OF WORK

3. SCOPE OF WORKS

4. SITE DESCRIPTION

5. GEOLOGY OF THE AREA

6. GEOLOGIC HAZARD AND SUBSURFACE CONDITION

7. PRELIMENARY CONCLUSION AND RECOMMENDATION

8. APPENDICES

A. VICINITY AND TEST PIT LOCATION MAP

B. SOIL PROFILE LOGS

C. SUMMARY OF TEST PIT RESULT

D. MACKINTOSH PROBE TEST LOG

E. DYNAMIC CONE PENETRATION TEST LOG

F. LABORATORY TEST RESULT

1. Sieve Analysis Test Result

2. Atterberg Limit Test Result

3. Moisture-density Test Result

4. Unconfined Compression Test

5. CBR & Swell Test

G. PHOTOS/ DOCUMENTATIONS
Geotechnical Investigation of Two-storey Residential Development: Brgy. Santiago, Malvar, Batangas

1.0 INTRODUCTION
This factual report presents the geotechnical investigation for the project TWO-
STOREY RESIDENTIAL DEVELOPMENT of CAMELLA LIMA located in Brgy. Santiago,
Malvar, Santiago as shown in figure 1. The work started on April 2019 and ends on
May 2019, conducted by the VERTEX Geotech team located in Daanghari, Molino IV,
Bacoor, Cavite.

2.0 PURPOSE OF WORK

This investigation was prepared to give the consultants/evaluators the necessary
information of the site’s condition, geologic characteristics and soil parameters for
evaluation and analysis purposes to determine the required safe bearing capacity of
foundation, swelling potential, and other geotechnical considerations.

It consists of 8 test pits location with samples excavated from 0.5m to 2.0m below
natural ground to determine the subsoil condition and characteristics of the existing
soil. The samples were brought to laboratory for testing and analysis.

3.0 SCOPE OF WORKS

The scope of work included in this investigation was based on the results generated
from field and laboratory testing and it includes:
a. Site Reconnaissance- the team conducted inspection in the site to investigate
relevant information that may affect the soil investigation.
b. Field Exploration- the fieldworks consists of excavating 8 test pits and
conducting 30 Mackintosh Probe Test (MPT) and 30 Dynamic cone Penetration
Test (DCPT). The test pits were excavated up to 2.0m depth, the MPT where
advanced up to maximum of 12 meters or when maximum blows are reach,
while the DCPT was advanced ranging from 1.0m to 1.2m depth. Field logs for
the following tests were recorded and analyzed for subsurface profiling.
c. Laboratory Testing- the bulk soil samples taken from site were delivered to the
laboratory for testing of their characteristics and property and as parameters to
be used for geotechnical analysis and evaluation.
d. Preliminary Engineering/ Geologic Evaluation based on Factual Report-
technical engineers undergo initial evaluation of the site using the soil
parameters being determined in the field and lab tests to generated initial
analysis and recommendation regarding the proposed site development.
e. Report Generation- the team prepared a report consisting of the full laboratory
result, field logs, findings, conclusions and recommendations.
Geotechnical Investigation of Two-storey Residential Development: Brgy. Santiago, Malvar, Batangas

4.0 SITE DESRIPTION

The site has a total area of 141,655 square meters and mostly covered with
vegetations (e.g. shrubs, corn plants, vines, and trees) at the time of site inspection.
The vicinity is bounded by the San Andres Road in the south which connects the
property by an access road; the Calabarzon Expressway in western part; the San
Juan Road in the north; and in the east by a narrow dirt road and Jose P. Laurel
Highway.

The site has an existing poultry located in the central part outside the property and
few houses situated inside the vicinity. Some trucks were also observed near the
houses in the entrance of the property.

Also, a creek (Amulungin creek) was situated in the western part outside the
property that crosses the expressway in the west and the San Andres Road in the
south. The terrain of the site is gently sloping with varying depths when sectioned
parallel eastward and steep slope in the northern part when sectioned parallel
North. The lowest elevation of the area is 85m above sea level and located in the
northern perimeter and highest elevation of 102m above sea level in the central east
of the property. Flow of water will be drawn towards north to concur with the
terrain of existing topography of the area.

The site has an on-going land development (clearing operation) in the middle
portion of the property at the time of testing.

5.0 GEOLOGY OF THE AREA

Based on initial analysis, the site’s geology composed of sticky and plastic silty clay
from surface up to 0.26m depth of weak and medium angular blocky structure; and
from 0.26 to 0.52m clay soil of weak fine and medium sub-angular structure layer
boundary could be observed. The type of rock is quaternary alluvium of
unconsolidated sediments of sand, silt and clay; the Guadalupe formation of
pyroclastics-tuff, tuffaceous sandstone and volcanic breccias were its composition
with conglomerate-sandstone-siltstone interbeds. (NOAA. US. Navy, 2018).

The distance from the nearest fault (West Valley Fault) is 20.6km NW and nearest
active volcano (Taal Volcano) is 16.3km W. (CNES, NOAA, U.S. Navy, 2018). The area
is not susceptible to liquefaction based on LDEO, NOAA map.
Geotechnical Investigation: Malvar, Batangas

A. MAPOUT LOCATION for MPT, DCPT, & TEST

PIT
Geotechnical Investigation: Malvar, Batangas

Upper Ground Floor, Worldwide Corporate

Project 1, MGS Office, Molino IV, Bacoor
Center
, Cavite
Shaw, Boulevard, 1552 Mandaluyong City,
Contact No. (02) 226 3552
Metro Manila
Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

Client Camella Communities, Inc.

Attention Engr. Robert Comia
Project Camella Lima
Location Malvar, Batangas

MAPOUT OF PROJECT SITE GEOTECHNICAL INVESTIGATION- TEST PIT

Prepared By: Noted By:

LAUREN S. GERENTE, ME-1 ENGR. RUBENSTEIN VALLO

Geotechnical Laboratory Teamleader Geotechnical Laboratory Team Head

Upper Ground Floor, Worldwide Corporate

Project 1, MGS Office, Molino IV, Bacoor
Geotechnical Investigation: Malvar, Batangas

Upper Ground Floor, Worldwide Corporate

Client Camella Communities, Inc.

Attention Engr. Robert Comia
Project Camella Lima
Location Malvar, Batangas

MAPOUT OF PROJECT SITE GEOTECHNICAL INVESTIGATION- MACKINTOSH PROBE TEST

Prepared By: Noted By:

LAUREN S. GERENTE, ME-1 ENGR. RUBENSTEIN VALLO

Geotechnical Laboratory Teamleader Geotechnical Laboratory Team Head

Upper Ground Floor, Worldwide Corporate

Project 1, MGS Office, Molino IV, Bacoor
Geotechnical Investigation: Malvar, Batangas

Upper Ground Floor, Worldwide Corporate

Client Camella Communities, Inc.

Attention Engr. Robert Comia
Project Camella Lima
Location Malvar, Batangas

MAPOUT OF PROJECT SITE GEOTECHNICAL INVESTIGATION- DYNAMIC CONE PENETRATION TEST

Prepared By: Noted By:

LAUREN S. GERENTE, ME-1 ENGR. RUBENSTEIN VALLO

Geotechnical Laboratory Teamleader Geotechnical Laboratory Team Head
Geotechnical Investigation: Malvar, Batangas

B. SOIL PROFILE LOGS

Geotechnical Investigation: Malvar, Batangas

Upper Ground Floor, Worldwide Corporate

Project 1, MGS Office, Molino IV, Bacoor ,
Center
Cavite
Shaw, Boulevard, 1552 Mandaluyong City,
Contact No. (02) 226 3552
Metro Manila
Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380

Client Camella Communities, Inc.

Attention Engr. Robert Comia LEGEND (SOIL TYPE):
Project Camella Lima GW GC SM CL CH
Location Malvar, Batangas GP SW SC OL OH
GM SP ML MH PT
SUBSURFACE SOIL PROFILE (TESTPITS)
TP 1 TP 2 TP 3 TP 4
Soil type: MH Soil type: MH Soil type: MH Soil type: MH
Liq Limit: 69 Liq Limit: 54 Liq Limit: 58 Liq Limit: 58
Plasticity: 30 Plasticity: 21 Plasticity: 16 Plasticity: 16
MDD,g/cc: 1.23 MDD,g/cc: 1.28 MDD,g/cc: 1.18 MDD,g/cc: 1.27
OMC, %: 34.82 OMC, %: 34.43 OMC, %: 30.61 OMC, %: 33.57
0.5M Soil type: SM Soil type: ML Soil type: MH Soil type: MH
Liq Limit: - Liq Limit: - Liq Limit: 56 Liq Limit: 66
Plasticity: - Plasticity: - Plasticity: 12 Plasticity: 28

MDD,g/cc: MDD,g/cc: MDD,g/cc: MDD,g/cc:

1.18 1.29 1.1 1.17
OMC, %: 39.59 OMC, %: 27.21 OMC, %: 46.67 OMC, %: 31.36
Soil type: SM Soil type: ML Soil type: SM Soil type: SM
Liq Limit: - Liq Limit: - Liq Limit: - Liq Limit: -
Plasticity: - Plasticity: - Plasticity: - Plasticity: -
MDD,g/cc: 1.18 MDD,g/cc: 1.27 MDD,g/cc: 1.15 MDD,g/cc: 1.21
OMC, %: 36.58 OMC, %: 36.11 OMC, %: 28.82 OMC, %: 38.24
1.5M Soil type: ML Soil type: ML Soil type: ML Soil type: MH
Liq Limit: - Liq Limit: - Liq Limit: - Liq Limit: 52
Plasticity: - Plasticity: - Plasticity: - Plasticity: 15

MDD,g/cc: 1.21 MDD,g/cc: 1.19 MDD,g/cc: 1.28 MDD,g/cc: 1.22

OMC, %: 31 OMC, %: 35 OMC, %: 30 OMC, %: 36

TP 5 TP6 TP7 TP15

Soil type: MH Soil type: ML Soil type: ML Soil type: MH
Liq Limit: 77 Liq Limit: - Liq Limit: 48 Liq Limit: 63
Plasticity: 38 Plasticity: - Plasticity: 15 Plasticity: 25
MDD,g/cc: 1.12 MDD,g/cc: 1.22 MDD,g/cc: 1.22 MDD,g/cc: 1.25
OMC, %: 36.68 OMC, %: 38.73 OMC, %: 39.84 OMC, %: 31.85
0.5M Soil type: CH Soil type: ML Soil type: MH Soil type: CH
Liq Limit: 54 Liq Limit: - Liq Limit: 69 Liq Limit: 62
Plasticity: 25 Plasticity: - Plasticity: 35 Plasticity: 22
MDD,g/cc: 1.15 MDD,g/cc: 1.13 MDD,g/cc: 1.12 MDD,g/cc: 1.24
OMC, %: 43.16 OMC, %: 40.41 OMC, %: 44.9 OMC, %: 40.6
Soil type: MH Soil type: MH Soil type: ML Soil type: MH
Liq Limit: - Liq Limit: 63 Liq Limit: - Liq Limit: 66
Plasticity: - Plasticity: 22 Plasticity: - Plasticity: 29
MDD,g/cc: 1.26 MDD,g/cc: 1.21 MDD,g/cc: 1.08 MDD,g/cc: 1.15
OMC, %: 34.02 OMC, %: 35.43 OMC, %: 38.37 OMC, %: 34.77
1.5M Soil type: ML Soil type: MH Soil type: ML Soil type: MH
Liq Limit: - Liq Limit: 59 Liq Limit: - Liq Limit: 57
Plasticity: - Plasticity: 12 Plasticity: - Plasticity: 9

MDD,g/cc: MDD,g/cc: MDD,g/cc: MDD,g/cc:

1.05 1.14 1.40 1.11
OMC, %: 48 OMC, %: 39 OMC, %: 27 OMC, %: 41

Prepared By: Noted By:

LAUREN S. GERENTE, ME-1 ENGR. RUBENSTEIN VALLO, CE
Geotechnical Laboratory Teamleader Geotechnical Laboratory Team Head
Geotechnical Investigation: Malvar, Batangas

C. SUMMARY OF TEST PIT RESULT

Project 1, MGS Office, Molino IV, Bacoor , Cavite
Upper Ground Floor, Worldwide Corporate Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552 Local: 0566 Cellphone No.: 0917-626-9380

Client : Camella Communities, Inc.

Attention : Engr. Robert Comia
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered: Soil Samples from Test Pits
Delivered by : Albert Catangue, Jesell Chavez, Roodney Ortal
Sampled by : Albert Catangue, Jesell Chavez, Roodney Ortal
Source : Test Pits
SUMMARY OF SOIL TEST RESULT
CAMELLA LIMA - MALVAR, BATANGAS

SPECIMEN IDENTIFICATION
TP1 TP2 TP3
TYPE OF TEST
0.5 M 1.0M 1.5M 2.0M 0.5 M 1.0M 1.5M 2.0M 0.5 M 1.0M 1.5M 2.0M
GRADING TEST
2 inch 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%
1 inch 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%
3/8 inch 92% 100% 99% 100% 100% 100% 100% 99% 94% 100% 99% 100%
No. 4 89% 100% 98% 100% 100% 100% 100% 98% 93% 100% 97% 100%
No.10 81% 94% 82% 99.80% 100% 100% 100% 98% 88% 99% 80% 96%
No.40 69.1% 68.2% 43.3% 91.90% 98.20% 98.3% 98.3% 95% 73.5% 86.4% 35% 77%
No.200 65.6% 46.7% 36.5% 78.90% 92.0% 93.7% 95.4% 91% 66.2% 77.2% 26.7% 54%
PLASTICITY TEST
Liquid Limit 69% - - - 54% - - - 58% 56% - -
Plastic Limit 39% - - - 33% - - - 42% 44% - -
Plasticity Index 30% - - - 21% - - - 16% 12% - -
Liquidity Index 0.57% - - - 0.52% - - - 0.14% 1.64% - -
MOISTURE CONTENT, % 56% 39% 42% 42% 53% 51% 68% 69% 44% 64% 48% 36%
COMPACTION TEST
Max. Dry Density, g/cc 1.23 1.18 1.23 1.21 1.28 1.29 1.27 1.19 1.18 1.1 1.15 1.28
Optimum Moisture Content, %: 34.82% 39.59% 36.58% 31% 34.43% 27.21% 36.11% 35% 30.61% 46.67% 28.82% 30%
UNCONFINED COMPRESSIVE STRENGTH q, MPa 0.081 - - - 0.05 - - - 0.046 0.062 - -
SOIL CLASSIFICATION MH SM SM ML MH ML ML ML MH MH SM ML

Prepared By: Noted By:

ALBERT CATANGUE, JESELL CHAVEZ, ROODNEY ORTAL LAUREN S. GERENTE ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Project 1, MGS Office, Molino IV, Bacoor , Cavite
Upper Ground Floor, Worldwide Corporate Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552 Local: 0566 Cellphone No.: 0917-626-9380

Client : Camella Communities, Inc.

Attention : Engr. Robert Comia
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : Soil Samples from Test Pits
Delivered by : Albert Catangue, Jesell Chavez, Roodney Ortal
Sampled by : Albert Catangue, Jesell Chavez, Roodney Ortal
Source : Test Pits
SUMMARY OF SOIL TEST RESULT
CAMELLA LIMA - MALVAR, BATANGAS

SPECIMEN IDENTIFICATION
TP4 TP5 TP6
TYPE OF TEST
0.5 M 1.0M 1.5M 2.0M 0.5 M 1.0M 1.5M 2.0M 0.5 M 1.0M 1.5M 2.0M
GRADING TEST
2 inch 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%
1 inch 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 96%
3/8 inch 90% 98% 100% 100% 100% 100% 100% 99% 100% 100% 99% 95%
No. 4 89% 96% 99% 100% 100% 100% 100% 99% 100% 100% 98% 93%
No.10 85% 91% 90% 100% 100% 100% 100% 98% 100% 100% 94% 82%
No.40 76.5% 71.7% 55.1% 92% 98.8% 98.8% 97.4% 94% 98.3% 98% 83.0% 64%
No.200 68.8% 62.8% 45.3% 82% 94.8% 94.7% 87.2% 85% 94.3% 94% 74.0% 51%
PLASTICITY TEST
Liquid Limit 58% 66% - 52% 77% 54% - - - - 63% 59%
Plastic Limit 43% 38% - 37% 39% 28% - - - - 41% 47%
Plasticity Index 16% 28% - 15% 38% 25% - - - - 22% 12%
Liquidity Index 0.55% 0.39% - 0.74% 0.46% 1.65% - - - - -0.21% -1.33%
MOISTURE CONTENT, % 51.00% 49.00% 47.00% 36.00% 56.00% 70.00% 65.00% 53% 58.00% 57.00% 36.00% 31%
COMPACTION TEST
Max. Dry Density, g/cc 1.27 1.17 1.21 1.22 1.12 1.15 1.26 1.05 1.22 1.13 1.21 1.14
Optimum Moisture Content, %: 33.57% 31.36% 38.24% 36% 36.68% 43.16% 34.02% 48% 38.73% 40.41% 35.43% 39%
UNCONFINED COMPRESSIVE STRENGTH q, MPa 0.06 0.078 - 0.063 0.039 0.019 - - - - 0.034 0.039
SOIL CLASSIFICATION MH MH SM MH MH CH MH ML ML ML MH MH

Prepared By: Noted By:

ALBERT CATANGUE, JESELL CHAVEZ, ROODNEY ORTAL LAUREN S. GERENTE ME-1

Client : Camella Communities, Inc.

Attention : Engr. Robert Comia
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : Soil Samples from Test Pits
Delivered by : Albert Catangue, Jesell Chavez, Roodney Ortal
Sampled by : Albert Catangue, Jesell Chavez, Roodney Ortal
Source : Test Pits
SUMMARY OF SOIL TEST RESULT
CAMELLA LIMA - MALVAR, BATANGAS

SPECIMEN IDENTIFICATION
TP7 TP15
TYPE OF TEST
0.5 M 1.0M 1.5M 2.0M 0.5 M 1.0M 1.5M 2.0M
GRADING TEST
2 inch 100% 100% 100% 100% 100% 100% 100% 100%
1 inch 100% 100% 100% 100% 100% 100% 100% 100%
3/8 inch 100% 100% 100% 99% 100% 98% 89% 96%
No. 4 96% 96% 100% 98% 99% 98% 85% 93%
No.10 96% 100% 100% 98% 98% 93% 79% 88%
No.40 99.5% 98.3% 96.8% 95% 97.2% 80.1% 69.1% 73%
No.200 92.4% 94.0% 89.2% 91% 93.1% 76.2% 64.2% 55%
PLASTICITY TEST
Liquid Limit 48% 69% - - 63% 62% 66% 57%
Plastic Limit 33% 34% - - 38% 40% 37% 48%
Plasticity Index 15% 35% - - 25% 22% 29% 9%
Liquidity Index 0.67% 0.50% - - 1.11% 0.55% 0.49% 0.98%
MOISTURE CONTENT, % 43.00% 51.00% 45.00% 19% 65% 52% 51% 57%
COMPACTION TEST
Max. Dry Density, g/cc 1.22 1.12 1.08 1.40 1.25 1.24 1.15 1.11
Optimum Moisture Content, %: 39.84% 44.90% 38.37% 27% 31.85% 40.60% 34.77% 41%
UNCONFINED COMPRESSIVE STRENGTH q, MPa 0.015 0.062 - - 0.092 0.042 0.107 0.062
SOIL CLASSIFICATION ML MH ML ML MH CH MH MH

Prepared By: Noted By:

ALBERT CATANGUE, JESELL CHAVEZ, ROODNEY ORTAL LAUREN S. GERENTE ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Geotechnical Investigation of Two-storey Residential Development : Brgy. Santiago, Malvar Batangas

D. MACKINTOSH PROBE TEST LOG

Project 1, MGS Office, Molino IV, Bacoor
Upper Ground Floor, Worldwide Corporate Center
, Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : 04.15.2019
Location Brgy. Santiago, Malvar, Batangas Date of Report : 04.29.2019
Tested by : Ortal, Pineda
Checked by : Lauren
MPT No. : 1

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

101 162 M1 Stiff 63 7

0.3
0.3

320 512 M2 Hard 223 22

0.6
0.6

248 396 M3 Hard 168 17

0.9
0.9

177 283 M4 Hard 116 12

1.2
1.2

178 285 M5 Hard 117 12

1.5
1.5

227 364 M6 Hard 153 16

1.8 1.8

219 351 M7 Hard 147 15

2.1 2.1

428 685 M8 Hard 307 29

2.4 2.4

431 690 M9 Hard 309 30

2.7 2.7

545 872.104522 M10 Hard 400 37

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency
Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

349 558 M1 Hard 245 24

0.3
0.3

348 556 M2 Hard 244 24

0.6
0.6

171 274 M3 Hard 112 12

0.9
0.9

478 764 M4 Hard 346 33

1.2
1.2

465 744 M5 Hard 336 32

1.5
1.5

188 300 M6 Hard 124 13

1.8 1.8

545 872 M7 Hard 400 37

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

214 342 M1 Hard 143 15

0.3
0.3

464 742 M2 Hard 335 32

0.6
0.6

390 624 M3 Hard 277 27

0.9
0.9

196 314 M4 Hard 130 13

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

120 192 M1 Very Stiff 76 8

0.3
0.3

483 772 M2 Hard 350 33

0.6
0.6

409 655 M3 Hard 292 28

0.9
0.9

234 375 M4 Hard 158 16

1.2
1.2

184 294 M5 Hard 121 13

1.5
1.5

545 872 M6 Hard 400 37

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

166 265 M1 Hard 108 11

0.3
0.3

316 506 M2 Hard 220 22

0.6
0.6

277 443 M3 Hard 190 19

0.9
0.9

196 314 M4 Hard 130 13

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

316 506 M1 Hard 220 22

0.3
0.3

314 502 M2 Hard 218 21

0.6
0.6

533 852 M3 Hard 390 36

0.9
0.9

250 400 M4 Hard 170 17

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

173 276 M1 Hard 113 12

0.3
0.3

449 718 M2 Hard 323 31

0.6
0.6

312 500 M3 Hard 217 21

0.9
0.9

337 540 M4 Hard 236 23

1.2
1.2

156 249 M5 Hard 101 11

1.5
1.5

170 272 M6 Hard 111 12

1.8 1.8

381 610 M7 Hard 270 26

2.1 2.1

545 872 M8 Hard 400 37

2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

164 263 M1 Hard 107 11

0.3
0.3

210 335 M2 Hard 140 14

0.6
0.6

279 447 M3 Hard 192 19

0.9
0.9

277 443 M4 Hard 190 19

1.2
1.2

316 506 M5 Hard 220 22

1.5
1.5

272 434 M6 Hard 186 19

1.8 1.8

382 612 M7 Hard 271 26

2.1 2.1

377 604 M8 Hard 267 26

2.4 2.4

545 872 M9 Hard 400 37

2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

276 441 M1 Hard 189 19

0.3
0.3

406 649 M2 Hard 289 28

0.6
0.6

363 581 M3 Hard 256 25

0.9
0.9

212 340 M4 Hard 142 15

1.2
1.2

123 197 M5 Very Stiff 78 8

1.5
1.5

146 233 M6 Very Stiff 94 10

1.8 1.8

117 188 M7 Very Stiff 74 8

2.1 2.1

120 192 M8 Very Stiff 76 8

2.4 2.4

114 183 M9 Very Stiff 72 8

2.7 2.7

120 192 M10 Very Stiff 76 8

3 3
0

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SUBSURFACE PROFILE SAMPLES

Blows/ 30 cm

N-Value
Consistency
Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
3

137 220 M11 Stiff 9

69 3.3 3.3

545 872 M12 Very Stiff 88 37

3.6 3.6

545 872 M13 Hard 400 37

3.9
3.9

4.2 4.2

0
4.5 4.5

0
4.8
4.8

0
5.1 5.1

0
5.4 5.4

5.7 5.7

0
6
6

GeoTech Team_Request Form_ Item G Page 10 of 10

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

400 641 M1 Hard 285 27

0.3
0.3

161 258 M2 Hard 105 11

0.6
0.6

119 190 M3 Very Stiff 75 8

0.9
0.9

406 649 M4 Hard 289 28

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

446 714 M1 Hard 321 31

0.3
0.3

483 772 M2 Hard 350 33

0.6
0.6

513 820 M3 Hard 374 35

0.9
0.9

545 872 M4 Hard 400 37

1.2
1.2

0
1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

545 872 M1 Hard 400 37

0.3
0.3

0
0.6
0.6

0
0.9
0.9

0
1.2
1.2

0
1.5
1.5

1.8 1.8

2.1 2.1

2.4 2.4

2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

278 445 M1 Hard 191 19

0.3
0.3

222 355 M2 Hard 149 15

0.6
0.6

242 387 M3 Hard 164 17

0.9
0.9

149 238 M4 Very Stiff 96 10

1.2
1.2

199 318 M5 Hard 132 14

1.5
1.5

278 445 M6 Hard 191 19

1.8 1.8

154 247 M7 Very Stiff 100 11

2.1 2.1

112 179 M8 Stiff 70 8

2.4 2.4

114 183 M9 Very Stiff 72 8

2.7 2.7

Medium
62 100 M10 (Firm)
37 4

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : 0
Project Camella Lima Date of Testing : 04.15.2019
Location Brgy. Santiago, Malvar, Batangas Date of Report : 04.29.2019
Tested by : Ortal, Pineda
Checked by : Lauren
MPT No. : 13

MACKINTOSH PROBING DATA

Corresponding
SUBSURFACE PROFILE SAMPLES

Blows/ 30 cm

N-Value
Consistency
Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
3

167 267 M11 Stiff 59 11

3.3 3.3

97 155 M12 Hard 109 7

3.6 3.6

97 155 M13 Stiff 60 7

3.9
3.9

110 176 M14 Stiff 69 8

4.2 4.2

166 265 M15 Hard 108 11

4.5 4.5

545 872 M16 Hard 400 37

4.8
4.8

0
5.1 5.1

0
5.4 5.4

5.7 5.7

0
6
6

GeoTech Team_Request Form_ Item G Page 10 of 10

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

455 728 M1 Hard 328 31

0.3
0.3

395 632 M2 Hard 281 27

0.6
0.6

314 502 M3 Hard 218 21

0.9
0.9

212 340 M4 Hard 142 15

1.2
1.2

160 256 M5 Hard 104 11

1.5
1.5

78 124 Stiff 47 5

1.8 1.8

103 165 Stiff 64 7

2.1 2.1

545 872 Hard 400 37

2.4 2.4

2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

464 742 M1 Hard 335 32

0.3
0.3

394 630 M2 Hard 280 27

0.6
0.6

250 400 M3 Hard 170 17

0.9
0.9

109 174 M4 Stiff 68 7

1.2
1.2

123 197 M5 Very Stiff 78 8

1.5
1.5

106 169 M6 Stiff 66 7

1.8 1.8

88 141 M7 Stiff 54 6

2.1 2.1

98 158 M8 Stiff 61 7
2.4 2.4

545 872 M9 Hard 400 37

2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

305 487 M1 Hard 211 21

0.3
0.3

230 368 M2 Hard 155 16

0.6
0.6

355 569 M3 Hard 250 24

0.9
0.9

103 165 M4 Stiff 64 7

1.2
1.2

147 236 M5 Very Stiff 95 10

1.5
1.5

163 260 M6 Hard 106 11

1.8 1.8

207 331 M7 Hard 138 14

2.1 2.1

363 581 M8 Hard 256 25

2.4 2.4

295 473 M9 Hard 204 20

2.7 2.7

248 396 M10 Hard 168 17

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

445 712 M1 Hard 320 30

0.3
0.3

545 872 M2 Hard 400 37

0.6
0.6

0
0.9
0.9

0
1.2
1.2

0
1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

195 311 M1 Hard 129 13

0.3
0.3

344 550 M2 Hard 241 24

0.6
0.6

489 782 M3 Hard 355 33

0.9
0.9

545 872 M4 Hard 400 37

1.2
1.2

M5 0
1.5
1.5

M6 0

1.8 1.8

M7 0

2.1 2.1

M8 0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

130 208 M1 Very Stiff 83 9

0.3
0.3

349 558 M2 Hard 245 24

0.6
0.6

420 671 M3 Hard 300 29

0.9
0.9

341 546 M4 Hard 239 23

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

Medium
66 105 M1 (Firm)
39 4
0.3
0.3

397 634 M2 Hard 282 27

0.6
0.6

432 692 M3 Hard 310 30

0.9
0.9

203 325 M4 Hard 135 14

1.2
1.2

355 569 M5 Hard 250 24

1.5
1.5

458 732 M6 Hard 330 31

1.8 1.8

310 496 M7 Hard 215 21

2.1 2.1

237 379 M8 Hard 160 16

2.4 2.4

207 331 M9 Hard 138 14

2.7 2.7

375 600 Hard 265 26

3 3

GeoTech Team_Request Form_ Item G

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SUBSURFACE PROFILE SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
3

286 458 M11 Hard 216 20

3.3 3.3

182 292 M12 Hard 197 12

3.6 3.6

182 292 M13 Hard 120 12

3.9
3.9

545 872 M14 Hard 400 37

4.2 4.2

0
4.5 4.5

0
4.8
4.8

0
5.1 5.1

0
5.4 5.4

5.7 5.7

0
6
6
Project 1, MGS Office, Molino IV, Bacoor
Upper Ground Floor, Worldwide Corporate Center
, Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m

Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

237 379 M1 Hard 160 16

0.3
0.3

388 620 M2 Hard 275 27

0.6
0.6

348 556 M3 Hard 244 24

0.9
0.9

293 468 M4 Hard 202 20

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3

GeoTech Team_Request Form_ Item G

Project 1, MGS Office, Molino IV,
Upper Ground Floor, Worldwide Corporate Center
Bacoor , Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

Depth
than 1.2m than 1.2m
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

112 179 M1 Stiff 70 8

0.3
0.3

327 523 M2 Hard 228 22

0.6
0.6

439 702 M3 Hard 315 30

0.9
0.9

385 616 M4 Hard 273 26

1.2
1.2

342 548 M5 Hard 240 23

1.5
1.5

219 351 M6 Hard 147 15

1.8 1.8

160 256 M7 Hard 104 11

2.1 2.1

191 305 M8 Hard 126 13

2.4 2.4

483 772 M9 Hard 350 33

2.7 2.7

545 872 M10 Hard 400 37

3 3
Project 1, MGS Office, Molino IV,
Upper Ground Floor, Worldwide Corporate Center
Bacoor , Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

Depth
than 1.2m than 1.2m
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

112 179 M1 Stiff 70 8

0.3
0.3

234 375 M2 Hard 158 16

0.6
0.6

305 487 M3 Hard 211 21

0.9
0.9

301 481 M4 Hard 208 21

1.2
1.2

193 309 M5 Hard 128 13

1.5
1.5

319 510 M6 Hard 222 22

1.8 1.8

455 728 M7 Hard 328 31

2.1 2.1

545 872 M8 Hard 400 37

2.4 2.4

0
2.7 2.7

0
3 3
Project 1, MGS Office, Molino IV,
Upper Ground Floor, Worldwide Corporate Center
Bacoor , Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Meyerhof's Bowles' Consistency
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

Depth
than 1.2m than 1.2m
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

168 269 M1 Hard 110 12

0.3
0.3

242 387 M2 Hard 164 17

0.6
0.6

231 370 M3 Hard 156 16

0.9
0.9

331 529 M4 Hard 231 23

1.2
1.2

303 485 M5 Hard 210 21

1.5
1.5

301 481 M6 Hard 208 21

1.8 1.8

197 316 M7 Hard 131 14

2.1 2.1

545 872 M8 Hard 400 37

2.4 2.4

0
2.7 2.7

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

188 300 M1 Hard 124 13

0.3
0.3

456 730 M2 Hard 329 31

0.6
0.6

420 671 M3 Hard 300 29

0.9
0.9

439 702 M4 Hard 315 30

1.2
1.2

545 872 M5 Hard 400 37

1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3
\
Project 1, MGS Office, Molino IV,
Upper Ground Floor, Worldwide Corporate Center
Bacoor , Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

139 222 M1 Very Stiff 89 10

0.3
0.3

400 641 M2 Hard 285 27

0.6
0.6

285 456 M3 Hard 196 20

0.9
0.9

233 372 M4 Hard 157 16

1.2
1.2

483 772 M5 Hard 350 33

1.5
1.5

294 470 M6 Hard 203 20

1.8 1.8

146 233 M7 Very Stiff 94 10

2.1 2.1

185 296 M8 Hard 122 13

2.4 2.4

545 872 M9 Hard 400 37

2.7 2.7

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

143 229 M1 Very Stiff 92 10

0.3
0.3

215 344 M2 Hard 144 15

0.6
0.6

167 267 M3 Hard 109 11

0.9
0.9

233 372 M4 Hard 157 16

1.2
1.2

126 202 M5 Very Stiff 80 9

1.5
1.5

207 331 M6 Hard 138 14

1.8 1.8

545 872 M7 Hard 400 37

2.1 2.1

0
2.4 2.4

0
2.7 2.7

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

200 320 M1 Hard 133 14

0.3
0.3

336 537 M2 Hard 235 23

0.6
0.6

248 396 M3 Hard 168 17

0.9
0.9

391 626 M4 Hard 278 27

1.2
1.2

200 320 M5 Hard 133 14

1.5
1.5

164 263 M6 Hard 107 11

1.8 1.8

100 160 M7 Stiff 62 7

2.1 2.1

94 150 M8 Stiff 58 6
2.4 2.4

133 213 M9 Very Stiff 85 9

2.7 2.7

93 148 M10 Stiff 57 6

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SUBSURFACE PROFILE SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m
width) Qa width) Qa Depth 0 100 200 300 400 500 600 700 800 900 1000
3

109 174 M11 Stiff 59 7

3.3 3.3

112 179 M12 Stiff 68 8

3.6
3.6

112 179 M13 Stiff 70 8

3.9
3.9

168 269 M14 Hard 110 12

4.2 4.2

189 303 M15 Hard 125 13

4.5 4.5

229 366 M16 Hard 154 16

4.8
4.8

311 498 M17 Hard 216 21

5.1 5.1

221 353 M18 Hard 148 15

5.4 5.4

230 368 M19 Hard 155 16

5.7 5.7

545 872 M20 Hard 400 37

6
6
Project 1, MGS Office, Molino IV, Bacoor
Upper Ground Floor, Worldwide Corporate Center
, Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

154 247 M1 Very Stiff 100 11

0.3
0.3

221 353 M2 Hard 148 15

0.6
0.6

545 872 M3 Hard 400 37

0.9
0.9

0
1.2
1.2

0
1.5
1.5

1.8 1.8

2.1 2.1

0
2.4 2.4

0
2.7 2.7

3 3
Project 1, MGS Office, Molino IV, Bacoor
Upper Ground Floor, Worldwide Corporate Center
, Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Manila
Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566
Local: 0566
` Cellphone No.: 0917-626-9380

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

91 146 M1 Stiff 56 6
0.3
0.3

174 278 M2 Hard 114 12

0.6
0.6

250 400 M3 Hard 170 17

0.9
0.9

452 724 M4 Hard 326 31

1.2
1.2

485 776 M5 Hard 352 33

1.5
1.5

279 447 M6 Hard 192 19

1.8 1.8

174 278 M7 Hard 114 12

2.1 2.1

170 272 M8 Hard 111 12

2.4 2.4

344 550 M9 Hard 241 24

2.7 2.7

545 872 M10 Hard 400 37

Client Camella Homes, Inc. Test Request Form No. : 10

MACKINTOSH PROBING DATA

Corresponding
SBC (based on 1in settlement & N-value) SAMPLES

Blows/ 30 cm

N-Value
Consistency

Meyerhof's Bowles'
Formula (less Formula (less Remarks
Symbols

Number

M- Value (Blows/30 cm)

than 1.2m than 1.2m Depth
width) Qa width) Qa 0 100 200 300 400 500 600 700 800 900 1000
0

140 224 M1 Very Stiff 90 10

0.3
0.3

154 247 M2 Very Stiff 100 11

0.6
0.6

230 368 M3 Hard 155 16

0.9
0.9

175 280 M4 Hard 115 12

1.2
1.2

243 390 M5 Hard 165 17

1.5
1.5

264 422 M6 Hard 180 18

1.8 1.8

394 630 M7 Hard 280 27

2.1 2.1

545 872 M8 Hard 400 37

2.4 2.4

0
2.7 2.7

3 3
Geotechnical Investigation of Two-storey Residential Development : Brgy. Santiago, Malvar Batangas

E. DYNAMIC CONE PENETRATION TEST LOG

Project 1, MGS Office, Molino IV,
Upper Ground Floor, Worldwide Corporate
Bacoor , Cavite
Center
Contact No. (02) 226 3552
Shaw Boulevard, 1552 Mandaluyong City,
Local: 0566
Metro Manila
Cellphone No.: 0917-626-9380

Client Camella Communities, Inc. Test Request Form No. : 11

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 247 42 881

18 268 43 908
19 289 44 934

20 312 45 963
21 335 46 989
22 346 47 1015
23 381 48 1041
24 400 49 1070

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 743 42 1130

18 790 43 1132
19 837 44 1134

20 888 45 1136
21 941 46 1139
22 965 47 1140
23 973 48 1143
24 983 49 1145

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 417 42 991

18 437 43 994
19 462 44 997

20 493 45 999
21 528 46 1000
22 568 47 1001
23 608 48 1002
24 644 49 1003

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 6
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 604 50 917 75 1172
1 27 26 622 51 930 76 1182
2 55 27 640 52 941 77 1193
3 77 28 658 53 951 78 1206
4 91 29 672 54 960 END OF LOG
5 120 30 686 55 968
6 137 31 697 56 976
7 154 32 709 57 986
8 172 33 721 58 994
9 194 34 733 59 1003
10 215 35 744 60 1012
11 237 36 755 61 1022
12 258 37 765 62 1032

13 281 38 774 63 1043

14 306 39 784 64 1053
15 331 40 795 65 1063
16 358 41 806 66 1074

17 402 42 820 67 1086

18 427 43 833 68 1098

19 448 44 847 69 1112

20 473 45 858 70 1126

21 501 46 870 71 1135

22 530 47 880 72 1145

23 575 48 893 73 1154

24 588 49 906 74 1163

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 8
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 480 50 715
1 56 26 502 51 725
2 74 27 523 52 737
3 84 28 534 53 751
4 98 29 540 54 771
5 113 30 544 55 798
6 128 31 549 56 924
7 147 32 551 57 953
8 163 33 556 58 975
9 170 34 560 59 995
10 201 35 562 60 1019
11 222 36 573 61 1042
12 246 37 579 62 1057
13 272 38 583 63 1068
14 302 39 591 64 1079
15 329 40 601 65 1098
16 354 41 613 66 1121

17 371 42 629 67 1134

18 384 43 643 68 1141

19 403 44 657 69 1151

20 420 45 666 70 1162

21 432 46 679 71 1176
22 445 47 686 END OF LOG
23 454 48 695
24 469 49 704

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 293 42 843

18 315 43 867
19 336 44 891

20 357 45 916
21 382 46 939
22 404 47 963
23 420 48 990
24 443 49 1018

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 11
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 485 50 849
1 14 26 493 51 871
2 25 27 500 52 896
3 40 28 506 53 922
4 54 29 511 54 946
5 70 30 523 55 970
6 91 31 529 56 995
7 112 32 536 57 1020
8 133 33 544 58 1050
9 157 34 552 59 1081
10 191 35 562 60 1109
11 228 36 572 61 1134
12 268 37 584 62 1163
13 298 38 596 63 1197
14 317 39 610 64 1227
15 335 40 626 END OF LOG
16 353 41 644

17 375 42 663

18 398 43 683
19 425 44 705

20 446 45 731
21 458 46 755
22 466 47 777
23 473 48 802
24 480 49 825

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 12
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 231 50 964
1 9 26 251 51 978
2 13 27 269 52 990
3 19 28 289 53 1002
4 24 29 308 54 1014
5 29 30 332 55 1027
6 35 31 357 56 1038
7 40 32 386 57 1040
8 45 33 416 58 1061
9 51 34 450 59 1070
10 59 35 486 60 1085
11 67 36 527 61 1099
12 73 37 568 62 1139
13 80 38 607 63 1154
14 89 39 642 64 1167
15 96 40 684 65 1183
16 108 41 718 66 1200

17 118 42 757 67 1217

18 130 43 791 68 1233

19 142 44 812 END OF LOG

20 153 45 833
21 168 46 854
22 182 47 877
23 197 48 906
24 215 49 939

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 228 42 806

18 239 43 833
19 251 44 880

20 264 45 919
21 278 46 955
22 293 47 992
23 311 48 1028
24 330 49 1067

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 279 42 888

18 294 43 921
19 309 44 958

20 327 45 996
21 354 46 1030
22 359 47 1067
23 377 48 1109
24 395 49 1141

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 251 42 1024

18 273 43 1047
19 287 44 1076

20 311 45 1098
21 335 46 1111
22 364 47 1126
23 393 48 1152
24 421 49 1171

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 16
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 438 50 970
1 24 26 455 51 994
2 40 27 471 52 1018
3 52 28 486 53 1040
4 73 29 507 54 1068
5 88 30 523 55 1102
6 97 31 540 56 1131
7 113 32 561 END OF LOG
8 127 33 582
9 142 34 599
10 159 35 621
11 175 36 642
12 198 37 663
13 221 38 688
14 244 39 713
15 260 40 737
16 274 41 761

17 292 42 786

18 308 43 811
19 327 44 835

20 346 45 856
21 367 46 880
22 386 47 902
23 407 48 925
24 422 49 948

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 17
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 221 50 610
1 13 26 232 51 633
2 21 27 243 52 658
3 30 28 253 53 684
4 39 29 264 54 710
5 45 30 275 55 736
6 53 31 284 56 764
7 62 32 296 57 793
8 69 33 307 58 820
9 76 34 319 59 848
10 84 35 330 60 877
11 93 36 344 61 907
12 100 37 357 62 937
13 107 38 371 63 966
14 117 39 386 64 998
15 126 40 401 65 1030
16 134 41 416 66 1061

17 143 42 431 67 1089

18 152 43 452 68 1114

19 160 44 471 69 1151

20 169 45 496 70 1181

21 179 46 512 71 1211
22 188 47 539 END OF LOG
23 199 48 563
24 210 49 586

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 307 42 869

18 318 43 899
19 335 44 923

20 350 45 948
21 365 46 975
22 384 47 998
23 403 48 1026
24 421 49 1057

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 19
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 622 50 857 75 1029
1 24 26 635 51 873 76 1034
2 43 27 643 52 881 77 1040
3 61 28 652 53 897 78 1046
4 80 29 657 54 906 79 1053
5 98 30 666 55 914 80 1059
6 117 31 673 56 925 81 1066
7 134 32 679 57 935 82 1074
8 152 33 692 58 945 83 1084
9 172 34 699 59 956 84 1091
10 191 35 707 60 962 85 1100
11 215 36 712 61 970 86 1107
12 238 37 714 62 973 87 1123
13 262 38 722 63 979 END OF LOG
14 290 39 728 64 984
15 319 40 739 65 989
16 353 41 758 66 992

17 392 42 777 67 992

18 425 43 797 68 996

19 456 44 806 69 1002

20 490 45 815 70 1005

21 529 46 824 71 1009
22 563 47 833 72 1014
23 582 48 841 73 1019
24 603 49 849 74 1023

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 328 42 1058

18 350 43 1089
19 374 44 1118

20 398 45 1151
21 424 END OF LOG
22 454
23 477
24 502

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 21
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 319 50 780 75 1093
1 24 26 334 51 787 76 1101
2 40 27 354 52 796 77 1106
3 54 28 374 53 806 78 1112
4 69 29 404 54 819 79 1117
5 85 30 421 55 834 80 1123
6 100 31 448 56 850 81 1129
7 119 32 473 57 865 82 1135
8 139 33 486 58 878 83 1142
9 159 34 495 59 889 84 1147
10 179 35 503 60 903 85 1153
11 199 36 511 61 918 86 1157
12 214 37 520 62 927 END OF LOG
13 224 38 533 63 953
14 231 39 548 64 973
15 239 40 566 65 980
16 245 41 580 66 990

17 252 42 598 67 1000

18 256 43 620 68 1013

19 260 44 652 69 1024

20 264 45 688 70 1034

21 269 46 712 71 1043
22 279 47 731 72 1053
23 290 48 756 73 1064
24 304 49 772 74 1079

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 22
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 400 50 580 75 627
1 64 26 413 51 581 76 628
2 82 27 427 52 583 77 631
3 97 28 445 53 584 78 633
4 112 29 461 54 585 79 637
5 127 30 480 55 587 80 639
6 145 31 498 56 590 81 643
7 166 32 516 57 591 82 645
8 182 33 527 58 593 83 648
9 202 34 535 59 594 84 651
10 221 35 540 60 596 85 653
11 241 36 546 61 600 86 656
12 256 37 550 62 602 87 660
13 267 38 553 63 603 88 663
14 283 39 556 64 604 89 666
15 301 40 558 65 605 90 670
16 309 41 561 66 606 91 671

17 318 42 563 67 609 92 675

18 324 43 565 68 611 93 678

19 331 44 566 69 612 94 682

20 340 45 569 70 615 95 683

21 350 46 571 71 617 96 688
22 362 47 572 72 618 97 691
23 375 48 574 73 620 98 701
24 388 49 576 74 623 99 705

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 22
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
100 711 125 921 150 1029 175 1071
101 717 126 931 151 1030 176 1073
102 725 127 941 152 1032 177 1074
103 733 128 951 153 1033 178 1078
104 742 129 958 154 1035 179 1079
105 752 130 964 155 1037 180 1080
106 764 131 970 156 1040 181 1081
107 773 132 975 157 1041 182 1085
108 781 133 980 158 1044 183 1088
109 790 134 984 159 1045 184 1091
110 797 135 989 160 1049 185 1094
111 803 136 991 161 1050 186 1096
112 809 137 995 162 1051 187 1099
113 816 138 999 163 1052 188 1101
114 825 139 1002 164 1054 189 1105
115 835 140 1005 165 1055 190 1110
116 839 141 1008 166 1057 191 1111

117 849 142 1011 167 1059 192 1115

118 859 143 1013 168 1060 193 1118

119 869 144 1016 169 1062 194 1121

120 877 145 1019 170 1064 195 1125

121 886 146 1021 171 1065 196 1128
122 892 147 1022 172 1066 197 1130
123 902 148 1026 173 1068 198 1135
124 911 149 1027 174 1069 199 1136

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

END OF LOG

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 304 42 1161

18 328 END OF LOG

19 352

20 377
21 403
22 430
23 460
24 491

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 24
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 543 50 854 75 1086
1 36 26 554 51 871 76 1096
2 54 27 565 52 884 77 1107
3 70 28 574 53 892 78 1117
4 85 29 581 54 902 79 1129
5 96 30 591 55 908 80 1140
6 105 31 600 56 916 81 1148
7 116 32 613 57 924 82 1156
8 125 33 627 58 932 83 1158
9 135 34 645 59 940 END OF LOG
10 146 35 659 60 949
11 162 36 665 61 957
12 185 37 672 62 966
13 214 38 678 63 977
14 246 39 685 64 987
15 282 40 693 65 996
16 311 41 698 66 1005

17 341 42 704 67 1014

18 375 43 712 68 1023

19 411 44 722 69 1030

20 442 45 732 70 1040

21 466 46 752 71 1049
22 495 47 778 72 1058
23 515 48 801 73 1067
24 531 49 825 74 1075

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 25
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 378 50 946
1 23 26 394 51 975
2 43 27 413 52 1003
3 62 28 429 53 1034
4 79 29 445 54 1066
5 97 30 463 55 1101
6 111 31 480 56 1137
7 126 32 499 57 1170
8 140 33 520 58 1200
9 155 34 541 59 1230
10 166 35 566 END OF LOG
11 176 36 590
12 189 37 615
13 201 38 638
14 215 39 662
15 228 40 687
16 243 41 712

17 259 42 736

18 274 43 761
19 290 44 788

20 303 45 815
21 318 46 840
22 333 47 865
23 348 48 890
24 363 49 918

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

17 310 42 1009

18 344 43 1037
19 375 44 1062

20 396 45 1091
21 423 46 1124
22 443 47 1159
23 468 48 1194
24 497 49 1230

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 27
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 367 50 976
1 16 26 384 51 1007
2 31 27 405 52 1032
3 41 28 429 53 1045
4 54 29 450 54 1056
5 66 30 474 55 1065
6 78 31 491 56 1077
7 88 32 506 57 1086
8 99 33 519 58 1094
9 110 34 532 59 1102
10 123 35 553 60 1104
11 135 36 587 61 1116
12 150 37 617 62 1124
13 167 38 645 63 1131
14 182 39 671 64 1139
15 204 40 706 65 1150
16 229 41 736 66 1164

17 247 42 779 67 1183

18 262 43 819 68 1208

19 283 44 848 END OF LOG

20 295 45 872
21 309 46 893
22 323 47 909
23 337 48 925
24 351 49 943

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 28
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 321 50 830
1 23 26 336 51 863
2 36 27 350 52 893
3 49 28 365 53 921
4 60 29 379 54 952
5 67 30 395 55 987
6 78 31 409 56 1024
7 88 32 423 57 1060
8 96 33 439 58 1095
9 106 34 454 59 1130
10 116 35 465 60 1158
11 128 36 485 61 1188
12 142 37 496 62 1217
13 157 38 513 END OF LOG
14 172 39 530
15 187 40 548
16 200 41 568

17 215 42 591

18 228 43 614
19 239 44 641

20 253 45 668
21 267 46 696
22 280 47 726
23 294 48 759
24 307 49 794

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 29
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 550 50 979
1 71 26 567 51 994
2 102 27 583 52 1010
3 116 28 599 53 1028
4 147 29 615 54 1045
5 170 30 630 55 1065
6 187 31 648 56 1084
7 205 32 668 57 1105
8 224 33 689 58 1128
9 240 34 712 59 1150
10 256 35 734 60 1174
11 272 36 760 61 1199
12 290 37 781 62 1223
13 308 38 797 END OF LOG
14 326 39 812
15 346 40 827
16 367 41 843

17 387 42 858

18 407 43 872
19 428 44 888

20 448 45 902
21 470 46 918
22 490 47 932
23 510 48 948
24 531 49 963

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Attention Engr. Robert Comia Date Received : -
Project Camella Lima Date of Testing : Apr-19
Location Malvar, Batangas Date of Report : May-19
Sample Delivered - Tested by : Chavez, Ortal, Pineda
Delivered by - Checked by : Lauren
Sampled by - DCP No. : 30
DYNAMIC CONE PENETRATION TEST
ASTM D6951
No. of Penetration No. of No. of Penetration No. of
Blows mm Blows Penetration mm Blows mm Blows Penetration mm
0 0 25 143 50 366 75 814
1 19 26 149 51 377 76 840
2 30 27 156 52 387 77 867
3 37 28 163 53 398 78 891
4 44 29 169 54 407 79 916
5 48 30 176 55 419 80 940
6 52 31 184 56 431 81 973
7 56 32 193 57 444 82 1011
8 61 33 202 58 457 83 1043
9 66 34 211 59 472 84 1063
10 71 35 220 60 485 85 1082
11 76 36 230 61 499 86 1101
12 79 37 241 62 515 87 1125
13 85 38 250 63 530 88 1193
14 88 39 260 64 541 89 1247
15 93 40 269 65 568 END OF LOG
16 98 41 280 66 589

17 103 42 289 67 612

18 109 43 300 68 635

19 115 44 309 69 659

20 117 45 319 70 680

21 122 46 327 71 701
22 128 47 336 72 732
23 133 48 345 73 758
24 138 49 356 74 786

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

1200

1000

800 DCPT 6
DCPT 7
DCPT 8

600 DCPT 9
DCPT 10

400

200

0
0 20 40 60 80 100

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

1200

1000

800 DCPT 11
DCPT 12
DCPT 13

600 DCPT 14
DCPT 15

400

200

0
0 10 20 30 40 50 60 70

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Client Camella Communities, Inc. Test Request Form No. : 11

1400

1200

1000

800 DCPT 21
DCPT 22
DCPT 23

600 DCPT 24
DCPT 25

400

200

0
0 50 100 150 200 250

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

Project 1, MGS Office, Molino
Upper Ground Floor, Worldwide
IV, Bacoor , Cavite
Corporate Center
Contact No. (02) 226 3552
Shaw Boulevard, 1552 Mandaluyong City,
Local: 0566
Metro Manila
Cellphone No.: 0917-626-

Client Camella Communities, Inc. Test Request Form No. : 11

1200

1000

800 DCPT 26
DCPT 27
DCPT 28
DCPT 29
600
DCPT 30

400

200

0
0 20 40 60 80 100

Prepared By: Witnessed By:

JESELL CHAVEZ LAUREN GERENTE, ME-1

Geotechnical Laboratory Technician Geotech Laboratory Team Leader

Noted By:

RUBENSTEIN VALLO, CE
Geotechnical Team Supervisor

GeoTech Team_Request Form_ Item H

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP1 - 0.5m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 96.2 %
1/2" 92.0 %
3/8" 92.0 %
No. 4 89.0 %
No. 10 81.0 %
No. 40 69.1 %
No. 200 65.6 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 69 %
Plastic Limit 39 %
Plasticity Index 30 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.23 g/cc
Optimum Moisture Content 34.82 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Project 1, MGS Office, Molino IV,
Upper Ground Floor, Worldwide Corporate Center Bacoor , Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Metro Contact No. (02) 226 3552
Manila Local: 0566
Contact No. (02) 226 3552 Local: 0566 Cellphone No.: 0917-626-9380

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.13.2019
Project: Camella Lima Date of Testing : 04.26.2019
Location: Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered: TP1 - 0.5m Tested by : ALBERT
Delivered by: J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by: J. Chavez, R. Ortal, A.J. Pineda
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 1_0.5 M Wt. of Sample w/ Tare, g 561.86 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 536.24 D25 = - D60= -
Weight of Tare, g 25.62 D30 = - D75= -

Mass of Soil Cumulative Cumulative #4 Coarse #10 Medium #40 Fine #200
Sieve Diameter Mass of GRAVEL SILT/CLAY
Sieve & Soil Retained % Retained % Passing SAND SAND SAND
Number (mm) Sieve (g)
(g) (g) (%) (%) 100
3" 76.200 484.7 484.7 0.0 0.0 100.0
2.5" 63.500 484.7 484.7 0.0 0.0 100.0 90
2" 50.800 494.8 494.8 0.0 0.0 100.0
1.5" 38.100 515.9 515.9 0.0 0.0 100.0 80
1" 25.400 505.6 505.6 0.0 0.0 100.0
70

% Passing
0.75" 19.050 519.5 539.99 20.5 3.8 96.2
0.5" 12.7 505.6 528.27 22.7 8.0 92.0
60
3/8" 9.525 497.7 513.36 15.7 11.0 89.0
4 4.750 473.6 516.91 43.3 19.0 81.0 50
8 2.360 0 0 0.0 19.0 81.0
10 2.000 430.5 470.87 40.4 26.6 73.4 40
12 1.700 0 0 0.0 26.6 73.4
16 1.180 0 0 0.0 26.6 73.4 30
18 1.000 0 0 0.0 26.6 73.4
20
20 0.850 0 0 0.0 26.6 73.4
30 0.600 0 0 0.0 26.6 73.4
10
35 0.500 0 0 0.0 26.6 73.4
40 0.425 337.1 360.41 23.3 30.9 69.1 0
50 0.300 0 0 0.0 30.9 69.1 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 30.9 69.1 Particle Diameter (mm)
80 0.180 0 0 0.0 30.9 69.1
100 0.150 0 0 0.0 30.9 69.1 Grain Size Distribution Curve
200 0.075 299.5 317.89 18.4 34.4 65.6 % Gravel: 19.046 D20: Cu: #VALUE!
Pan 366.2 718.24 352.0 100.0 0.0 % Sand: 15.305 D30: - Cc: #VALUE!
TOTAL: 536.2 % Fines: 65.650 D60: - So: #VALUE!
Fineness Modulus 1.679 GI: 20.641 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV,
Center Bacoor , Cavite
Shaw, Boulevard, 1552 Mandaluyong City, Contact No. (02) 226 3552
Metro Manila Local: 0566
Contact No. (02) 226 3552 Local: 0566 Cellphone No.: 0917-626-9380

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 04.26.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP1 - 0.5m Tested by : ANDRE
Delivered by : Earl John Torralba Checked by : LAUREN
Sampled by : Earl John Torralba Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 31 29 22 19
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.4 10.64 12.48 12.06 4.49 4.50 4.10 4.35
Mass Can & Soil (Wet) MCMS (g) 17.25 17.4 52.8 53.24 13.26 13.26 13.33 13.34
Mass Can & Soil (Dry) MCDS (g) 15.33 15.51 38.3 38.5 9.84 9.71 9.53 9.52
Mass of Soil MS (g) 4.93 4.87 25.82 26.44 5.35 5.21 5.43 5.17
Mass of Water MW (g) 1.92 1.89 14.50 14.74 3.42 3.55 3.80 3.82
Water Content w (%) 38.9 38.8 56.2 55.7 63.93 68.14 69.98 73.89

Liquid Limit (LL or w L ) (%): 69 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 39 50 4 4

CH
Plasticity Index (PI) (%): 30 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 56 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.57 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.33 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -16.84ln(x) + 123.02
40 R² = 0.8811

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Project 1, MGS Office, Molino IV, Bacoor ,
Upper Ground Floor, Worldwide Corporate
Cavite
Center
Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City,
Local: 0566
Metro Manila
Cellphone No.: 0917-626-9380

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 04.26.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP1 - 0.5m Tested by : ALBERT
Delivered by : J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2830.4 3006.4 3251.5 3264.2 3178.5 1.25
Mass in Grams Mold 1686 1686 1686 1686 1686
Wet Soil 1144.4 1320.4 1565.5 1578.2 1492.5
Wet Density , g/cc 1.21 1.40 1.66 1.67 1.58 1.20
Can Number 1 2 3 4 5
Can + Wet Soil (1) 63.12 62.74 65.04 67.17 67.63

Dry Unit Weight

Can + Dry Soil (1) 57.04 53.74 52.94 52.45 51.4 1.15
Mass in Grams Water (1) 6.08 9 12.1 14.72 16.23
Can (1) 22.14 18.69 18.42 18.76 20.33
1.10
Dry Soil (1) 34.9 35.05 34.52 33.69 31.07
Can + Wet Soil (2) 61.9 62.9 65.9 68.4 68.8
Can + Dry Soil (2) 56.0 53.8 54.0 53.4 51.7 1.05
Mass in Grams Water (2) 5.9 9.1 11.9 15.0 17.1
Can (2) 18.6 18.0 19.6 19.2 18.6
Dry Soil (2) 37.5 35.8 34.4 34.2 33.0 1.00
Water Content % 16.63% 25.48% 34.82% 43.72% 52.05% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.04 1.12 1.23 1.16 1.04 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.23 OMC (%): 34.82%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 0
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 1-0.5m Tested by : ALBERT
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 1-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1126.39 0.000
0.254 0.003 5.7 36.18 1130.10 0.032 Unconfined Compression Test-TP1-0.5m
0.508 0.007 10.5 66.64 1133.84 0.059 0.090
0.762 0.010 13.4 85.05 1137.60 0.075 0.080
1.016 0.013 14.5 92.03 1141.38 0.081
1.524 0.020 8 50.77 1149.03 0.044 0.070
2.032 0.026 4 25.39 1156.78 0.022

Applied Stress, MPa

0.033 1164.63 0.060
2.54 5 31.73 0.027
3.048 0.039 4.2 26.66 1172.59 0.023 0.050
3.556 0.046 3.4 21.58 1180.66 0.018
4.064 0.053 2.8 17.77 1188.84 0.015 0.040
4.572 0.059 2.5 15.87 1197.14 0.013
0.030
5.08 0.066 2.2 13.96 1205.55 0.012
6.096 0.079 2 12.69 1222.74 0.010 0.020
7.112 0.092 2 12.69 1240.42 0.010
8.128 0.105 1.5 9.52 1258.63 0.008 0.010
9.144 0.118 0.6 3.81 1277.37 0.003
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.36333 Unconfined Compression Test
Moist weight, g : 104.5 Diameter of sample: 37.88 Compressive strength, qu: 0.081 MPa
Oven-dry wt, g : 74.1 Area of sample: 1126.392 Undrained cohesion, cu: 0.161 MPa
Moisture content: 40.99 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

0 - 0.024 Very soft
0.024 - 0.048 Soft
Prepared By: Noted By: 0.048 - 0.096 Medium
0.096 - 0.192 Stiff
ALBERT CATANGUE LAUREN S. GERENTE, ME-1 0.192 - 0.383 Very stiff
Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader 1 Megapascal = 20,885.46 psf

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP1 - 1.0m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 99.5 %
3/8" 99.5 %
No. 4 99.5 %
No. 10 93.7 %
No. 40 68.2 %
No. 200 46.7 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.18 g/cc
Optimum Moisture Content 39.59 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION SM BROWNISH NON PLASTIC SILTY SAND

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 1_1.0 M Wt. of Sample w/ Tare, g 638.9 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 515.4 D25 = - D60= -
Weight of Tare, g 123.5 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 508.11 2.5 0.5 99.5
60
3/8" 9.525 497.7 497.7 0.0 0.5 99.5
4 4.750 473.6 503.38 29.8 6.3 93.7 50
8 2.360 0 0 0.0 6.3 93.7
10 2.000 430.5 516.06 85.6 22.9 77.1 40
12 1.700 0 0 0.0 22.9 77.1
16 1.180 0 0 0.0 22.9 77.1 30
18 1.000 0 0 0.0 22.9 77.1
20
20 0.850 0 0 0.0 22.9 77.1
30 0.600 0 0 0.0 22.9 77.1
10
35 0.500 0 0 0.0 22.9 77.1
40 0.425 337.1 382.89 45.8 31.8 68.2 0
50 0.300 0 0 0.0 31.8 68.2 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 31.8 68.2 Particle Diameter (mm)
80 0.180 0 0 0.0 31.8 68.2
100 0.150 0 0 0.0 31.8 68.2 Grain Size Distribution Curve
200 0.075 299.5 410.69 111.2 53.3 46.7 % Gravel: 6.265 D20: Cu: #VALUE!
Pan 366.2 606.77 240.6 100.0 0.0 % Sand: 47.059 D30: - Cc: #VALUE!
TOTAL: 515.4 % Fines: 46.676 D60: - So: #VALUE!
Fineness Modulus 1.222 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Upper Ground Floor, Worldwide Corporate Center Project 1, MGS Office, Molino IV,
Shaw, Boulevard, 1552 Mandaluyong City, Metro Bacoor , Cavite
Manila Contact No. (02) 226 3552
Contact No. (02) 226 3552 Local: 0566 Local: 0566
Cellphone No.: 0917-626-9380

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 04.25.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP1 - 1.0m Tested by : ALBERT
Delivered by : J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by : J. Chavez, R. Ortal, A.J. Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 12.21 12.58 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 59.33 59.82 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 45.66 46.89 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 33.45 34.31 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 13.67 12.93 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 40.9 37.7 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 30 115.89 70
Moisture Content (%): 39 CL
USCS Classification: 20 MH
SM 0 0
AASHTO Classification: A-4 10 70 70 ML
CL-ML
BROWNISH NON PLASTIC
Soil Desciption SILTY SAND 0
Liquidity Index #DIV/0! 0 7 10 20 7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 50 15.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation 30 25 0
X Multipoint
Procedure B: Fall Cone
25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2961.8 3174 3347.7 3542.1 3485.1 1.40
Mass in Grams Mold 1991 1991 1991 1991 1991
Wet Soil 970.8 1183 1356.7 1551.1 1494.1 1.20
Wet Density , g/cc 1.03 1.25 1.44 1.64 1.58
Can Number 1 2 3 4 5 1.00
Can + Wet Soil (1) 62.19 62.72 62.11 62.71 62.57

Dry Unit Weight

Can + Dry Soil (1) 58.65 55.49 52.55 50.21 48.13 0.80
Mass in Grams Water (1) 3.54 7.23 9.56 12.5 14.44
Can (1) 21.52 18.56 18.61 18.65 19.37 0.60
Dry Soil (1) 37.1 36.93 33.94 31.56 28.76
Can + Wet Soil (2) 62.3 62.5 62.3 62.4 62.6 0.40
Can + Dry Soil (2) 58.5 55.3 53.4 49.9 48.9
Mass in Grams Water (2) 3.9 7.3 8.9 12.5 13.7 0.20
Can (2) 18.8 19.1 21.1 18.4 21.1
Dry Soil (2) 39.6 36.2 32.4 31.5 27.8 0.00
Water Content % 9.65% 19.81% 27.85% 39.59% 49.69% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 0.94 1.05 1.13 1.18 1.06 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.18 OMC (%): 39.59%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP1 - 1.5m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 98.6 %
3/8" 98.6 %
No. 4 97.8 %
No. 10 82.1 %
No. 40 43.3 %
No. 200 36.5 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.23 g/cc
Optimum Moisture Content 36.58 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION SM BROWNISH NON PLASTIC SILTY SAND

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 1_1.5 M Wt. of Sample w/ Tare, g 652.9 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 520.4 D25 = - D60= -
Weight of Tare, g 132.5 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 512.68 7.1 1.4 98.6
60
3/8" 9.525 497.7 501.96 4.3 2.2 97.8
4 4.750 473.6 555.59 82.0 17.9 82.1 50
8 2.360 0 0 0.0 17.9 82.1
10 2.000 430.5 550.05 119.6 40.9 59.1 40
12 1.700 0 0 0.0 40.9 59.1
16 1.180 0 0 0.0 40.9 59.1 30
18 1.000 0 0 0.0 40.9 59.1
20
20 0.850 0 0 0.0 40.9 59.1
30 0.600 0 0 0.0 40.9 59.1
10
35 0.500 0 0 0.0 40.9 59.1
40 0.425 337.1 419.09 82.0 56.7 43.3 0
50 0.300 0 0 0.0 56.7 43.3 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 56.7 43.3 Particle Diameter (mm)
80 0.180 0 0 0.0 56.7 43.3
100 0.150 0 0 0.0 56.7 43.3 Grain Size Distribution Curve
200 0.075 299.5 335.16 35.7 63.5 36.5 % Gravel: 17.934 D20: Cu: #VALUE!
Pan 366.2 556.07 189.9 100.0 0.0 % Sand: 45.580 D30: - Cc: #VALUE!
TOTAL: 520.4 % Fines: 36.485 D60: - So: #VALUE!
Fineness Modulus 2.332 GI: #DIV/0! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 02.16.2019
Location : Pili, Camarines Sur Date of Report : 02.26.2019
Sample Delivered
: TP1 - 1.5m Tested by : ALBERT
Delivered by : Chavez, Ortal, Pineda Checked by : LAUREN
Sampled by : Chavez, Ortal, Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 12.97 12.73 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 56.29 56.31 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 43.57 43.22 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 30.60 30.49 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 12.72 13.09 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 41.6 42.9 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 60 4 4

CH
Plasticity Index (PI) (%): #DIV/0! 5025.5 4
Activity of Clay: - 115.89 70
40
Moisture Content (%): 42 CL
USCS Classification: 30 0 MH
SM 0
AASHTO Classification: A-4 20 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILTY SAND 10
Liquidity Index #DIV/0! 7 7
0 Liquid Limit (LL or wL)
Consistency Index #DIV/0! 29.6 7
0 10 20 30 40 50 60 70 80 90 100
70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 50 15.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 02.21.2019
Location : Malvar, Batangas Date of Report : 02.26.2019
Sample Delivered : TP1 - 1.5m Tested by : ALBERT
Delivered by : J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2797.8 2948.3 3127.2 3271.7 3209.9 1.25
Mass in Grams Mold 1686 1686 1686 1686 1686
Wet Soil 1111.8 1262.3 1441.2 1585.7 1523.9
Wet Density , g/cc 1.18 1.34 1.53 1.68 1.62 1.20
Can Number 1 2 3 4 5
Can + Wet Soil (1) 64.31 61.65 62.91 62.6 69.35

Dry Unit Weight

Can + Dry Soil (1) 57.65 53.57 51.49 49.55 53.38 1.15
Mass in Grams Water (1) 6.66 8.08 11.42 13.05 15.97
Can (1) 12.75 12.19 12.63 12.46 12.92
1.10
Dry Soil (1) 44.9 41.38 38.86 37.09 40.46
Can + Wet Soil (2) 63.4 61.6 62.8 62.8 69.9
Can + Dry Soil (2) 58.2 53.3 51.1 48.8 52.2 1.05
Mass in Grams Water (2) 5.2 8.4 11.7 14.0 17.7
Can (2) 11.9 12.6 12.2 12.1 12.4
Dry Soil (2) 46.3 40.7 38.9 36.8 39.8 1.00
Water Content % 13.02% 20.04% 29.73% 36.58% 41.96% 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00%
Dry Density g/cc 1.04 1.12 1.18 1.23 1.14 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.23 OMC (%): 36.58%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100 %
No. 4 100 %
No. 10 99.8 %
No. 40 91.9 %
No. 200 78.9 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.21 g/cc
Optimum Moisture Content 31.45 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 1_2.0 M Wt. of Sample w/ Tare, g 541.98 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 516.36 D25 = - D60= -
Weight of Tare, g 25.62 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 474.89 1.3 0.2 99.8 50
8 2.360 0 0 0.0 0.2 99.8
10 2.000 430.5 443.78 13.3 2.8 97.2 40
12 1.700 0 0 0.0 2.8 97.2
16 1.180 0 0 0.0 2.8 97.2 30
18 1.000 0 0 0.0 2.8 97.2
20
20 0.850 0 0 0.0 2.8 97.2
30 0.600 0 0 0.0 2.8 97.2
10
35 0.500 0 0 0.0 2.8 97.2
40 0.425 337.1 364.43 27.3 8.1 91.9 0
50 0.300 0 0 0.0 8.1 91.9 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 8.1 91.9 Particle Diameter (mm)
80 0.180 0 0 0.0 8.1 91.9
100 0.150 0 0 0.0 8.1 91.9 Grain Size Distribution Curve
200 0.075 299.5 366.55 67.1 21.1 78.9 % Gravel: 0.250 D20: Cu: #VALUE!
Pan 366.2 773.61 407.4 100.0 0.0 % Sand: 20.850 D30: - Cc: #VALUE!
TOTAL: 516.4 % Fines: 78.900 D60: - So: #VALUE!
Fineness Modulus 0.224 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 02.16.2019
Location : Malvar, Batangas Date of Report : 02.26.2019
Sample Delivered
: TP1 - 2.0m Tested by : ALBERT
Delivered by : Chavez, Ortal, Pineda Checked by : LAUREN
Sampled by : Chavez, Ortal, Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 12.19 12.64 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 52.72 52.87 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 40.85 40.94 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 28.66 28.30 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 11.87 11.93 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 41.4 42.2 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 42 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 02.21.2019
Location : Malvar, Batangas Date of Report : 02.26.2019
Sample Delivered : TP1 - 2.0m Tested by : ALBERT
Delivered by : J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2826.7 3007.5 3188 3239 3218.8 1.22
Mass in Grams Mold 1686 1686 1686 1686 1686
Wet Soil 1140.7 1321.5 1502 1553 1532.8 1.20
Wet Density , g/cc 1.21 1.40 1.59 1.65 1.63
Can Number 1 2 3 4 5 1.18
Can + Wet Soil (1) 65.84 62.19 66.94 61.75 66.31

Dry Unit Weight

1.16
Can + Dry Soil (1) 60.98 54.39 55.37 49.37 51.16
Mass in Grams Water (1) 4.86 7.8 11.57 12.38 15.15 1.14
Can (1) 22.44 18.94 18.43 18.52 18.67
Dry Soil (1) 38.5 35.45 36.94 30.85 32.49 1.12
Can + Wet Soil (2) 66.6 62.9 67.1 62.4 66.4
1.10
Can + Dry Soil (2) 61.3 54.6 55.6 49.9 51.3
Mass in Grams Water (2) 5.3 8.3 11.5 12.6 15.1 1.08
Can (2) 21.1 18.6 19.3 18.6 17.9
Dry Soil (2) 40.2 36.0 36.4 31.3 33.4 1.06
Water Content % 12.91% 22.46% 31.45% 40.17% 45.97% 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00% 50.00%
Dry Density g/cc 1.07 1.14 1.21 1.17 1.11 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.21 OMC (%): 31.45%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP2 - 0.5m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100 %
No. 4 100 %
No. 10 100 %
No. 40 98.2 %
No. 200 92.0 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 54 %
Plastic Limit 33 %
Plasticity Index 21 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.28 g/cc
Optimum Moisture Content 34.43 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-6

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 2_0.5 M Wt. of Sample w/ Tare, g 541.02 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 515.62 D25 = - D60= -
Weight of Tare, g 25.4 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 430.5 0.0 0.0 100.0 40
12 1.700 0 0 0.0 0.0 100.0
16 1.180 0 0 0.0 0.0 100.0 30
18 1.000 0 0 0.0 0.0 100.0
20
20 0.850 0 0 0.0 0.0 100.0
30 0.600 0 0 0.0 0.0 100.0
10
35 0.500 0 0 0.0 0.0 100.0
40 0.425 337.1 346.42 9.3 1.8 98.2 0
50 0.300 0 0 0.0 1.8 98.2 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.8 98.2 Particle Diameter (mm)
80 0.180 0 0 0.0 1.8 98.2
100 0.150 0 0 0.0 1.8 98.2 Grain Size Distribution Curve
200 0.075 299.5 331.42 31.9 8.0 92.0 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 840.58 474.4 100.0 0.0 % Sand: 7.998 D30: - Cc: #VALUE!
TOTAL: 515.6 % Fines: 92.002 D60: - So: #VALUE!
Fineness Modulus 0.036 GI: 23.689 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 05.07.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP2 - 0.5m Tested by : Albert
Delivered by : Chavez, Ortal, Pineda Checked by : LAUREN
Sampled by : Chavez, Ortal, Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 33 27 22 17
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.33 10.3 12.16 12.02 10.24 10.57 10.00 10.48
Mass Can & Soil (Wet) MCMS (g) 20.28 20.2 60.33 60.23 29.08 29.51 29.48 29.98
Mass Can & Soil (Dry) MCDS (g) 17.85 17.74 45.66 45.61 22.56 22.89 22.65 23.14
Mass of Soil MS (g) 7.52 7.44 33.50 33.59 12.32 12.32 12.65 12.66
Mass of Water MW (g) 2.43 2.46 14.67 14.62 6.52 6.62 6.83 6.84
Water Content w (%) 32.3 33.1 43.8 43.5 52.92 53.73 53.99 54.03

Liquid Limit (LL or w L ) (%): 54 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 33 50 4 4

CH
Plasticity Index (PI) (%): 21 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 44 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-6 10 70 70 ML
CL-ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.52 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.30 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40
y = -1.581ln(x) + 58.696
Dry Preparation Procedure B: Fall 30 25 0 R² = 0.7597
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2879.9 3017.9 3157.8 3311.5 3262 1.30
Mass in Grams Mold 1686 1686 1686 1686 1686
1.28
Wet Soil 1193.9 1331.9 1471.8 1625.5 1576
Wet Density , g/cc 1.27 1.41 1.56 1.72 1.67 1.26
Can Number 1 2 3 4 5 1.24
Can + Wet Soil (1) 67.13 66.2 63.52 66.04 66.19 1.22

Dry Unit Weight

Can + Dry Soil (1) 61.18 58.35 54.09 54.83 51.8
1.20
Mass in Grams Water (1) 5.95 7.85 9.43 11.21 14.39
Can (1) 18.74 18.02 18.83 22.05 18.8 1.18
Dry Soil (1) 42.4 40.33 35.26 32.78 33 1.16
Can + Wet Soil (2) 67.2 67.2 63.7 66.0 66.9 1.14
Can + Dry Soil (2) 61.0 59.4 54.1 54.6 52.9
1.12
Mass in Grams Water (2) 6.1 7.9 9.6 11.5 14.0
Can (2) 18.7 19.5 18.7 21.5 20.6 1.10
Dry Soil (2) 42.3 39.8 35.5 33.0 32.4 1.08
Water Content % 14.24% 19.60% 26.88% 34.43% 43.37% 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00% 50.00%
Dry Density g/cc 1.11 1.18 1.23 1.28 1.17 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.28 OMC (%): 34.43%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 0
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 2-0.5m Tested by : ALBERT
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 2-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1126.19 0.000
0.254 0.003 3 19.04 1129.90 0.017 Unconfined Compression Test-TP2-0.5m
0.508 0.007 7.2 45.70 1133.62 0.040 0.060
0.762 0.010 9 57.12 1137.37 0.050
1.016 0.013 3.5 22.21 1141.15 0.019 0.050
1.524 0.020 0.5 3.17 1148.77 0.003
2.032 0.026 0.5 3.17 1156.50 0.003

Applied Stress, MPa

0.033 1164.34 0.040
2.54 0.4 2.54 0.002
3.048 0.039 0.4 2.54 1172.28 0.002
3.556 0.046 0.4 2.54 1180.33 0.002 0.030
4.064 0.052 0.4 2.54 1188.49 0.002
4.572 0.059 0.5 3.17 1196.76 0.003
0.020
5.08 0.066 0.5 3.17 1205.15 0.003
6.096 0.079 0.5 3.17 1222.29 0.003
7.112 0.092 0.5 3.17 1239.93 0.003 0.010
8.128 0.105 0.5 3.17 1258.08 0.003
9.144 0.118 0.5 3.17 1276.76 0.002
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.53667 Unconfined Compression Test
Moist weight, g : 116.0 Diameter of sample: 37.88 Compressive strength, qu: 0.050 MPa
Oven-dry wt, g : 90.4 Area of sample: 1126.194 Undrained cohesion, cu: 0.100 MPa
Moisture content: 28.24 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Axial Splitting
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP2 - 1.0m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100 %
No. 4 100 %
No. 10 100 %
No. 40 98.3 %
No. 200 93.7 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.29 g/cc
Optimum Moisture Content 27.21 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 2_1.0 M Wt. of Sample w/ Tare, g 619.77 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 540.24 D25 = - D60= -
Weight of Tare, g 79.53 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 430.56 0.1 0.0 100.0 40
12 1.700 0 0 0.0 0.0 100.0
16 1.180 0 0 0.0 0.0 100.0 30
18 1.000 0 0 0.0 0.0 100.0
20
20 0.850 0 0 0.0 0.0 100.0
30 0.600 0 0 0.0 0.0 100.0
10
35 0.500 0 0 0.0 0.0 100.0
40 0.425 337.1 346.38 9.3 1.7 98.3 0
50 0.300 0 0 0.0 1.7 98.3 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.7 98.3 Particle Diameter (mm)
80 0.180 0 0 0.0 1.7 98.3
100 0.150 0 0 0.0 1.7 98.3 Grain Size Distribution Curve
200 0.075 299.5 324.41 24.9 6.3 93.7 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 872.19 506.0 100.0 0.0 % Sand: 6.340 D30: - Cc: #VALUE!
TOTAL: 540.2 % Fines: 93.660 D60: - So: #VALUE!
Fineness Modulus 0.035 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 04.24.2019
Location : Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered
: TP2 - 1.0m Tested by : ALBERT
Delivered by : Chavez, Ortal, Pineda Checked by : LAUREN
Sampled by : Chavez, Ortal, Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 12.29 12.93 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 60.65 60.74 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 44.28 44.49 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 31.99 31.56 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 16.37 16.25 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 51.2 51.5 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 51 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2871.7 3052.1 3238.5 3312.2 3236.5 1.35
Mass in Grams Mold 1686 1686 1686 1686 1686
Wet Soil 1185.7 1366.1 1552.5 1626.2 1550.5
1.30
Wet Density , g/cc 1.26 1.45 1.65 1.72 1.64
Can Number 1 2 3 4 5
Can + Wet Soil (1) 64.41 65.57 64.88 68.83 68.32 1.25

Dry Unit Weight

Can + Dry Soil (1) 58.39 57.19 55.03 55.79 52.88
Mass in Grams Water (1) 6.02 8.38 9.85 13.04 15.44 1.20
Can (1) 18.82 18.41 20.09 21.11 20.66
Dry Soil (1) 39.6 38.78 34.94 34.68 32.22
1.15
Can + Wet Soil (2) 64.3 66.3 64.3 68.0 67.0
Can + Dry Soil (2) 58.6 57.7 54.8 55.6 52.0
Mass in Grams Water (2) 5.7 8.6 9.5 12.4 15.0 1.10
Can (2) 19.0 19.2 18.7 22.4 18.7
Dry Soil (2) 39.6 38.5 36.2 33.2 33.4 1.05
Water Content % 14.80% 21.94% 27.21% 37.54% 46.43% 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00% 50.00%
Dry Density g/cc 1.10 1.19 1.29 1.25 1.12 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.29 OMC (%): 27.21%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP1 - 1.5m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100 %
No. 4 100 %
No. 10 100 %
No. 40 98.3 %
No. 200 95.4 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.27 g/cc
Optimum Moisture Content 36.11 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.13.2019
Project: Camella Lima Date of Testing : 05.09.2019
Location: Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered: TP1 - 1.5m Tested by : ALBERT
Delivered by: J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by: J. Chavez, R. Ortal, A.J. Pineda
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 2_1.5 M Wt. of Sample w/ Tare, g 600.04 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 520.47 D25 = - D60= -
Weight of Tare, g 79.57 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 430.64 0.1 0.0 100.0 40
12 1.700 0 0 0.0 0.0 100.0
16 1.180 0 0 0.0 0.0 100.0 30
18 1.000 0 0 0.0 0.0 100.0
20
20 0.850 0 0 0.0 0.0 100.0
30 0.600 0 0 0.0 0.0 100.0
10
35 0.500 0 0 0.0 0.0 100.0
40 0.425 337.1 345.69 8.6 1.7 98.3 0
50 0.300 0 0 0.0 1.7 98.3 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.7 98.3 Particle Diameter (mm)
80 0.180 0 0 0.0 1.7 98.3
100 0.150 0 0 0.0 1.7 98.3 Grain Size Distribution Curve
200 0.075 299.5 314.46 15.0 4.6 95.4 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 862.98 496.8 100.0 0.0 % Sand: 4.552 D30: - Cc: #VALUE!
TOTAL: 520.5 % Fines: 95.448 D60: - So: #VALUE!
Fineness Modulus 0.034 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.13.2018
Project : Camella Lima Date of Testing : 05.09.2019
Location : Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered
: TP1 - 1.5m Tested by : ALBERT
Delivered by : Chavez, Ortal, Pineda Checked by : LAUREN
Sampled by : Chavez, Ortal, Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 12.12 12.22 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 60.86 60.47 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 41.2 40.94 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 29.08 28.72 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 19.66 19.53 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 67.6 68.0 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 68 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 05.09.2019
Location : Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered : TP1 - 1.5m Tested by : ALBERT
Delivered by : J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2794 3025.7 3314.9 3276 0 1.40
Mass in Grams Mold 1686 1686 1686 1686 0
Wet Soil 1108 1339.7 1628.9 1590 0 1.20
Wet Density , g/cc 1.17 1.42 1.73 1.69 0.00
Can Number 1 2 3 4 5 1.00
Can + Wet Soil (1) 62.78 64.23 63.99 61.61 0

Dry Unit Weight

Can + Dry Soil (1) 56.66 55.36 51.9 48.59 0 0.80
Mass in Grams Water (1) 6.12 8.87 12.09 13.02 0
Can (1) 18.8 21.78 18.08 19.7 0 0.60
Dry Soil (1) 37.9 33.58 33.82 28.89 0
Can + Wet Soil (2) 62.5 64.9 64.2 63.0 0.0 0.40
Can + Dry Soil (2) 56.4 56.5 52.1 48.0 0.0
Mass in Grams Water (2) 6.1 8.5 12.1 14.9 0.0 0.20
Can (2) 19.1 22.1 18.9 18.7 0.0
Dry Soil (2) 37.3 34.4 33.2 29.4 0.0 0.00
Water Content % 16.21% 25.50% 36.11% 47.94% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.01 1.13 1.27 1.14 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.27 OMC (%): 36.11%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP2 - 2.0m
Delivered by : J. Chavez, R. Ortal, A.J. Pineda
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 98.7 %
3/8" 98.7 %
No. 4 98.4 %
No. 10 98.1 %
No. 40 94.7 %
No. 200 91.3 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.19 g/cc
Optimum Moisture Content 34.62 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.13.2019
Project: Camella Lima Date of Testing : 05.10.2019
Location: Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered: TP2 - 2.0m Tested by : ALBERT
Delivered by: J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by: J. Chavez, R. Ortal, A.J. Pineda
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 2_2.0 M Wt. of Sample w/ Tare, g 679.9 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 521.85 D25 = - D60= -
Weight of Tare, g 158.05 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 512.48 6.9 1.3 98.7
60
3/8" 9.525 497.7 499.23 1.5 1.6 98.4
4 4.750 473.6 475.19 1.6 1.9 98.1 50
8 2.360 0 0 0.0 1.9 98.1
10 2.000 430.5 435.87 5.4 2.9 97.1 40
12 1.700 0 0 0.0 2.9 97.1
16 1.180 0 0 0.0 2.9 97.1 30
18 1.000 0 0 0.0 2.9 97.1
20
20 0.850 0 0 0.0 2.9 97.1
30 0.600 0 0 0.0 2.9 97.1
10
35 0.500 0 0 0.0 2.9 97.1
40 0.425 337.1 349.26 12.2 5.3 94.7 0
50 0.300 0 0 0.0 5.3 94.7 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 5.3 94.7 Particle Diameter (mm)
80 0.180 0 0 0.0 5.3 94.7
100 0.150 0 0 0.0 5.3 94.7 Grain Size Distribution Curve
200 0.075 299.5 317.26 17.8 8.7 91.3 % Gravel: 1.916 D20: Cu: #VALUE!
Pan 366.2 842.76 476.6 100.0 0.0 % Sand: 6.762 D30: - Cc: #VALUE!
TOTAL: 521.9 % Fines: 91.321 D60: - So: #VALUE!
Fineness Modulus 0.219 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr, Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 05.10.2019
Location : Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered
: TP2 - 2.0m Tested by : ALBERT
Delivered by : Chavez, Ortal, Pineda Checked by : LAUREN
Sampled by : Chavez, Ortal, Pineda Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 0 0 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 0 0 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 0 0 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! #DIV/0! #DIV/0! #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): #DIV/0! CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.13.2019
Project : Camella Lima Date of Testing : 05.10.2019
Location : Malvar, Batangas Date of Report : 05.30.2019
Sample Delivered : TP2 - 2.0m Tested by : ALBERT
Delivered by : J. Chavez, R. Ortal, A.J. Pineda Checked by : LAUREN
Sampled by : J. Chavez, R. Ortal, A.J. Pineda
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3208.9 3500.7 3564.5 3501.7 0 1.20
Mass in Grams Mold 1991 1991 1991 1991 0
1.18
Wet Soil 1217.9 1509.7 1573.5 1510.7 0
Wet Density , g/cc 1.29 1.60 1.67 1.60 0.00 1.16
Can Number 1 2 3 4 5 1.14
Can + Wet Soil (1) 60.07 63.06 64.95 65.38 0

Dry Unit Weight

Can + Dry Soil (1) 49.69 49.03 46.49 44.21 0 1.12
Mass in Grams Water (1) 10.38 14.03 18.46 21.17 0 1.10
Can (1) 8.59 8.74 8.06 8.28 0
1.08
Dry Soil (1) 41.1 40.29 38.43 35.93 0
Can + Wet Soil (2) 60.2 62.6 64.1 64.3 0.0 1.06
Can + Dry Soil (2) 49.7 48.8 46.3 43.6 0.0 1.04
Mass in Grams Water (2) 10.5 13.8 17.9 20.7 0.0
Can (2) 1.02
8.3 8.8 8.0 8.1 0.0
Dry Soil (2) 41.4 40.0 38.2 35.5 0.0 1.00
Water Content % 25.36% 34.62% 47.38% 58.58% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.03 1.19 1.13 1.01 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.19 OMC (%): 34.62%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP3 - 0.5m
Delivered by : A.Catangue, J.Chavez, R. Ortal
Sampled by : A.Catangue, J.Chavez, R. Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 95.9 %
1/2" 94.2 %
3/8" 94.2 %
No. 4 93.1 %
No. 10 87.8 %
No. 40 73.5 %
No. 200 66.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 58 %
Plastic Limit 42 %
Plasticity Index 16 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.18 g/cc
Optimum Moisture Content 30.61 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.17.2019
Project: Camella Lima Date of Testing : 04.25.2019
Location: Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered: TP3 - 0.5m Tested by : ROODNEY
Delivered by: A.Catangue, J.Chavez, R. Ortal Checked by : LAUREN
Sampled by: A.Catangue, J.Chavez, R. Ortal
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 3_0.5 M Wt. of Sample w/ Tare, g 633.2 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 502.8 D25 = - D60= -
Weight of Tare, g 130.4 D30 = - D75= -

% Passing
0.75" 19.050 519.5 539.99 20.5 4.1 95.9
0.5" 12.7 505.6 514.03 8.4 5.8 94.2
60
3/8" 9.525 497.7 503.24 5.5 6.9 93.1
4 4.750 473.6 500.35 26.8 12.2 87.8 50
8 2.360 0 0 0.0 12.2 87.8
10 2.000 430.5 479.18 48.7 21.9 78.1 40
12 1.700 0 0 0.0 21.9 78.1
16 1.180 0 0 0.0 21.9 78.1 30
18 1.000 0 0 0.0 21.9 78.1
20
20 0.850 0 0 0.0 21.9 78.1
30 0.600 0 0 0.0 21.9 78.1
10
35 0.500 0 0 0.0 21.9 78.1
40 0.425 337.1 360.65 23.6 26.5 73.5 0
50 0.300 0 0 0.0 26.5 73.5 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 26.5 73.5 Particle Diameter (mm)
80 0.180 0 0 0.0 26.5 73.5
100 0.150 0 0 0.0 26.5 73.5 Grain Size Distribution Curve
200 0.075 299.5 336.09 36.6 33.8 66.2 % Gravel: 12.174 D20: Cu: #VALUE!
Pan 366.2 698.97 332.8 100.0 0.0 % Sand: 21.643 D30: - Cc: #VALUE!
TOTAL: 502.8 % Fines: 66.183 D60: - So: #VALUE!
Fineness Modulus 1.321 GI: 11.979 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 04.26.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP3 - 0.5m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 31 26 23 16
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.39 10.44 12.32 12.32 10.43 10.41 10.36 10.21
Mass Can & Soil (Wet) MCMS (g) 22.67 22.55 60.36 60.7 24.42 24.86 24.80 24.74
Mass Can & Soil (Dry) MCDS (g) 19.06 18.99 45.2 46.48 19.60 19.50 19.35 19.23
Mass of Soil MS (g) 8.67 8.55 32.88 34.16 9.17 9.09 8.99 9.02
Mass of Water MW (g) 3.61 3.56 15.16 14.22 4.82 5.36 5.45 5.51
Water Content w (%) 41.6 41.6 46.1 41.6 52.56 58.97 60.62 61.09

Liquid Limit (LL or w L ) (%): 58 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 42 50 4 4

CH
Plasticity Index (PI) (%): 16 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 44 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.14 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.33 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40 y = -11.25ln(x) + 93.736
R² = 0.6389
Dry Preparation Procedure B: Fall 30 25 0
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2823.9 3142.5 3256.9 3360.00 0 1.20
Mass in Grams Mold 1686 1686 1686 1686 0
1.18
Wet Soil 1137.9 1456.5 1570.9 1674 0
Wet Density , g/cc 1.21 1.54 1.67 1.78 0.00 1.16
Can Number 1 2 3 4 5 1.14
Can + Wet Soil (1) 52.65 52.49 52.53 52.61 0

Dry Unit Weight

Can + Dry Soil (1) 46.07 43.12 40.19 38.14 0 1.12
Mass in Grams Water (1) 6.58 9.37 12.34 14.47 0 1.10
Can (1) 12.48 12.08 12.91 12.73 0
1.08
Dry Soil (1) 33.6 31.04 27.28 25.41 0
Can + Wet Soil (2) 52.6 52.4 52.5 52.5 0.0 1.06
Can + Dry Soil (2) 45.9 42.9 39.9 37.8 0.0 1.04
Mass in Grams Water (2) 6.6 9.5 12.6 14.8 0.0
Can (2) 1.02
12.2 12.2 12.3 12.2 0.0
Dry Soil (2) 33.8 30.7 27.6 25.6 0.0 1.00
Water Content % 19.60% 30.61% 45.40% 57.25% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.01 1.18 1.15 1.13 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.18 OMC (%): 30.61%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 3-0.5m Tested by : ROODNEY
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 3-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1118.48 0.000
0.254 0.003 2.75 17.45 1122.20 0.016 Unconfined Compression Test-TP3-0.5m
0.508 0.007 4.5 28.56 1125.95 0.025 0.050
0.762 0.010 6.5 41.25 1129.73 0.037
1.016 0.013 7 44.43 1133.53 0.039 0.040
1.524 0.020 8.25 52.36 1141.21 0.046
2.032 0.027 5 31.73 1148.99 0.028

Applied Stress, MPa

0.033 1156.88 0.030
2.54 3 19.04 0.016
3.048 0.040 3.25 20.63 1164.88 0.018
3.556 0.046 3.5 22.21 1172.99 0.019 0.020
4.064 0.053 3.25 20.63 1181.22 0.017
4.572 0.060 1 6.35 1189.56 0.005
0.010
5.08 0.066 0.25 1.59 1198.02 0.001
6.096 0.080 0 0.00 1215.30 0.000
7.112 0.093 0 0.00 1233.09 0.000 0.000
8.128 0.106 0 0.00 1251.41 0.000 0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
9.144 0.120 0 0.00 1270.29 0.000
-0.010
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 76.51333 Unconfined Compression Test
Moist weight, g : 88.7 Diameter of sample: 37.75 Compressive strength, qu: 0.046 MPa
Oven-dry wt, g : 65.1 Area of sample: 1118.477 Undrained cohesion, cu: 0.092 MPa
Moisture content: 36.31 Proving Ring Calibration Factor: 6.34682 Consistency: Soft
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

0 - 0.024 Very soft
0.024 - 0.048 Soft
Prepared By: Noted By: 0.048 - 0.096 Medium
0.096 - 0.192 Stiff
ROODNEY ORTAL LAUREN S. GERENTE, ME-1 0.192 - 0.383 Very stiff
Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader 1 Megapascal = 20,885.46 psf

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP3 - 1.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 100.0 %
No. 40 86.4 %
No. 200 77.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 56 %
Plastic Limit 44 %
Plasticity Index 12 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.10 g/cc
Optimum Moisture Content 46.67 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 3_1.0 M Wt. of Sample w/ Tare, g 648.7 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 515.5 D25 = - D60= -
Weight of Tare, g 133.2 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 475.46 45.0 8.7 91.3 40
12 1.700 0 0 0.0 8.7 91.3
16 1.180 0 0 0.0 8.7 91.3 30
18 1.000 0 0 0.0 8.7 91.3
20
20 0.850 0 0 0.0 8.7 91.3
30 0.600 0 0 0.0 8.7 91.3
10
35 0.500 0 0 0.0 8.7 91.3
40 0.425 337.1 362.29 25.2 13.6 86.4 0
50 0.300 0 0 0.0 13.6 86.4 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 13.6 86.4 Particle Diameter (mm)
80 0.180 0 0 0.0 13.6 86.4
100 0.150 0 0 0.0 13.6 86.4 Grain Size Distribution Curve
200 0.075 299.5 347.04 47.5 22.8 77.2 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 764.01 397.8 100.0 0.0 % Sand: 22.830 D30: - Cc: #VALUE!
TOTAL: 515.5 % Fines: 77.170 D60: - So: #VALUE!
Fineness Modulus 0.447 GI: 13.167 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 04.30.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP3 - 1.0m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 31 28 23 16
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 4.44 3.99 12.07 12.43 10.25 10.27 10.25 10.20
Mass Can & Soil (Wet) MCMS (g) 15.74 15.4 60.36 60.76 28.18 28.07 28.03 28.30
Mass Can & Soil (Dry) MCDS (g) 12.29 11.93 41.3 42.17 22.06 21.68 21.47 21.52
Mass of Soil MS (g) 7.85 7.94 29.23 29.74 11.81 11.41 11.22 11.32
Mass of Water MW (g) 3.45 3.47 19.06 18.59 6.12 6.39 6.56 6.78
Water Content w (%) 43.9 43.7 65.2 62.5 51.82 56.00 58.47 59.89

Liquid Limit (LL or w L ) (%): 56 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 44 50 4 4

CH
Plasticity Index (PI) (%): 12 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 64 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 1.64 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index -0.18 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40
y = -10.71ln(x) + 90.481
30 25 0 R² = 0.7798
Dry Preparation Procedure B: Fall
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.07.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP3 - 1.0m Tested by : ROODNEY
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2777.8 3041.9 3207.1 3127.5 0 1.12
Mass in Grams Mold 1686 1686 1686 1686 0
Wet Soil 1091.8 1355.9 1521.1 1441.5 0 1.10
Wet Density , g/cc 1.16 1.44 1.61 1.53 0.00 1.08
Can Number 1 2 3 4 5
Can + Wet Soil (1) 60.52 60.58 60.6 60.8 0 1.06

Dry Unit Weight

Can + Dry Soil (1) 53.04 49.88 47.27 45.12 0 1.04
Mass in Grams Water (1) 7.48 10.7 13.33 15.68 0
Can (1) 18.9 18.47 18.54 19.07 0 1.02
Dry Soil (1) 34.1 31.41 28.73 26.05 0
1.00
Can + Wet Soil (2) 60.7 60.4 60.6 60.6 0.0
Can + Dry Soil (2) 53.0 49.7 47.0 45.3 0.0 0.98
Mass in Grams Water (2) 7.7 10.8 13.6 15.3 0.0
0.96
Can (2) 18.6 18.8 17.9 19.2 0.0
Dry Soil (2) 34.4 30.9 29.0 26.1 0.0 0.94
Water Content % 22.09% 34.48% 46.67% 59.50% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 0.95 1.07 1.10 0.96 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.10 OMC (%): 46.67%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 3-1.0m Tested by : ROODNEY
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 3-1.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1108.42 0.000
0.254 0.003 3.25 20.63 1112.07 0.019 Unconfined Compression Test-TP3-1.0m
0.508 0.007 5.25 33.32 1115.74 0.030 0.070
0.762 0.010 6.75 42.84 1119.44 0.038
0.060
1.016 0.013 8.75 55.53 1123.16 0.049
1.524 0.020 11 69.82 1130.68 0.062
0.050
2.032 0.026 6.5 41.25 1138.29 0.036

Applied Stress, MPa

2.54 0.033 1 6.35 1146.02 0.006 0.040
3.048 0.039 0.25 1.59 1153.84 0.001
3.556 0.046 0 0.00 1161.77 0.000 0.030
4.064 0.052 0.75 4.76 1169.82 0.004
4.572 0.059 1.25 7.93 1177.97 0.007 0.020
5.08 0.066 0.5 3.17 1186.24 0.003
6.096 0.079 0.25 1.59 1203.14 0.001 0.010
7.112 0.092 0 0.00 1220.52 0.000
0.105 1238.41 0.000
8.128 0.25 1.59 0.001
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
9.144 0.118 0.25 1.59 1256.84 0.001
-0.010
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.43667 Unconfined Compression Test
Moist weight, g : 106.3 Diameter of sample: 37.58 Compressive strength, qu: 0.062 MPa
Oven-dry wt, g : 74.4 Area of sample: 1108.425 Undrained cohesion, cu: 0.123 MPa
Moisture content: 42.87 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Multiple fracturing
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP3 - 1.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 99.4 %
3/8" 99.4 %
No. 4 96.5 %
No. 10 79.6 %
No. 40 35.1 %
No. 200 26.7 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.15 g/cc
Optimum Moisture Content 28.82 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION SM BROWNISH NON PLASTIC SILTY SAND

A-2-4

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 3_1.5 M Wt. of Sample w/ Tare, g 809.2 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 675.2 D25 = - D60= -
Weight of Tare, g 134 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 509.42 3.8 0.6 99.4
60
3/8" 9.525 497.7 517.75 20.1 3.5 96.5
4 4.750 473.6 587.74 114.1 20.4 79.6 50
8 2.360 0 0 0.0 20.4 79.6
10 2.000 430.5 573.1 142.6 41.6 58.4 40
12 1.700 0 0 0.0 41.6 58.4
16 1.180 0 0 0.0 41.6 58.4 30
18 1.000 0 0 0.0 41.6 58.4
20
20 0.850 0 0 0.0 41.6 58.4
30 0.600 0 0 0.0 41.6 58.4
10
35 0.500 0 0 0.0 41.6 58.4
40 0.425 337.1 494.93 157.8 64.9 35.1 0
50 0.300 0 0 0.0 64.9 35.1 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 64.9 35.1 Particle Diameter (mm)
80 0.180 0 0 0.0 64.9 35.1
100 0.150 0 0 0.0 64.9 35.1 Grain Size Distribution Curve
200 0.075 299.5 355.81 56.3 73.3 26.7 % Gravel: 20.440 D20: Cu: #VALUE!
Pan 366.2 546.65 180.5 100.0 0.0 % Sand: 52.835 D30: - Cc: #VALUE!
TOTAL: 675.2 % Fines: 26.725 D60: - So: #VALUE!
Fineness Modulus 2.574 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.14.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP3 - 1.5m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 12.41 12.65 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 60.38 60.82 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 44.76 45.48 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 32.35 32.83 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 15.62 15.34 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 48.3 46.7 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 48 CL
USCS Classification: 20 MH
SM 0 0
AASHTO Classification: A-2-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILTY SAND 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2724.5 2918.1 3086.7 3099.6 0 1.18
Mass in Grams Mold 1686 1686 1686 1686 0
1.16
Wet Soil 1038.5 1232.1 1400.7 1413.6 0
Wet Density , g/cc 1.10 1.31 1.49 1.50 0.00 1.14
Can Number 1 2 3 4 5 1.12
Can + Wet Soil (1) 60.63 60.67 60.56 60.31 0 1.10

Dry Unit Weight

Can + Dry Soil (1) 56.29 53.56 51.18 48.91 0
1.08
Mass in Grams Water (1) 4.34 7.11 9.38 11.4 0
Can (1) 18.65 18.52 18.74 19.24 0 1.06
Dry Soil (1) 37.6 35.04 32.44 29.67 0 1.04
Can + Wet Soil (2) 60.5 60.5 60.6 60.4 0.0 1.02
Can + Dry Soil (2) 56.1 53.5 51.2 48.8 0.0
1.00
Mass in Grams Water (2) 4.4 7.0 9.4 11.6 0.0
Can (2) 18.5 17.9 18.6 19.0 0.0 0.98
Dry Soil (2) 37.6 35.7 32.6 29.8 0.0 0.96
Water Content % 11.68% 19.95% 28.82% 38.60% #DIV/0! 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00%
Dry Density g/cc 0.99 1.09 1.15 1.08 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.15 OMC (%): 28.82%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP3 - 2.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 95.9 %
No. 40 77.4 %
No. 200 53.8 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.28 g/cc
Optimum Moisture Content 29.56 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML GRAYISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 3_2.0 M Wt. of Sample w/ Tare, g 587.5 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 516 D25 = - D60= -
Weight of Tare, g 71.5 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 494.53 20.9 4.1 95.9 50
8 2.360 0 0 0.0 4.1 95.9
10 2.000 430.5 458.28 27.8 9.4 90.6 40
12 1.700 0 0 0.0 9.4 90.6
16 1.180 0 0 0.0 9.4 90.6 30
18 1.000 0 0 0.0 9.4 90.6
20
20 0.850 0 0 0.0 9.4 90.6
30 0.600 0 0 0.0 9.4 90.6
10
35 0.500 0 0 0.0 9.4 90.6
40 0.425 337.1 404.8 67.7 22.6 77.4 0
50 0.300 0 0 0.0 22.6 77.4 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 22.6 77.4 Particle Diameter (mm)
80 0.180 0 0 0.0 22.6 77.4
100 0.150 0 0 0.0 22.6 77.4 Grain Size Distribution Curve
200 0.075 299.5 421.53 122.0 46.2 53.8 % Gravel: 4.056 D20: Cu: #VALUE!
Pan 366.2 643.76 277.6 100.0 0.0 % Sand: 42.153 D30: - Cc: #VALUE!
TOTAL: 516.0 % Fines: 53.791 D60: - So: #VALUE!
Fineness Modulus 0.721 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.15.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP3 - 2.0m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 19.57 18.56 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 68.42 68.26 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 55.29 55.28 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 35.72 36.72 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 13.13 12.98 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 36.8 35.3 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 36 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
GRAYISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3341.5 3553.5 3571 3578.5 0 1.29
Mass in Grams Mold 1991 1991 1991 1991 0
1.28
Wet Soil 1350.5 1562.5 1580 1587.5 0
Wet Density , g/cc 1.43 1.66 1.68 1.68 0.00 1.27
Can Number 1 2 3 4 5 1.26
Can + Wet Soil (1) 60.38 60.23 60.57 60.58 0 1.25

Dry Unit Weight

Can + Dry Soil (1) 54.39 51.07 48.94 48.4 0
1.24
Mass in Grams Water (1) 5.99 9.16 11.63 12.18 0
Can (1) 18.44 19.54 18.59 18.87 0 1.23
Dry Soil (1) 36.0 31.53 30.35 29.53 0 1.22
Can + Wet Soil (2) 60.3 60.9 60.5 60.3 0.0 1.21
Can + Dry Soil (2) 54.3 51.9 49.0 48.0 0.0
1.20
Mass in Grams Water (2) 6.0 9.0 11.5 12.2 0.0
Can (2) 18.0 22.1 19.6 18.8 0.0 1.19
Dry Soil (2) 36.3 29.8 29.4 29.3 0.0 1.18
Water Content % 16.61% 29.56% 38.75% 41.54% #DIV/0! 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00%
Dry Density g/cc 1.23 1.28 1.21 1.19 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.28 OMC (%): 29.56%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP4 - 0.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 96.5 %
1/2" 90.1 %
3/8" 90.1 %
No. 4 89.1 %
No. 10 85.2 %
No. 40 76.5 %
No. 200 68.8 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 58 %
Plastic Limit 43 %
Plasticity Index 16 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.27 g/cc
Optimum Moisture Content 33.57 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 4_0.5 M Wt. of Sample w/ Tare, g 589.4 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 521.3 D25 = - D60= -
Weight of Tare, g 68.1 D30 = - D75= -

% Passing
0.75" 19.050 519.5 537.95 18.5 3.5 96.5
0.5" 12.7 505.6 538.74 33.1 9.9 90.1
60
3/8" 9.525 497.7 503.04 5.3 10.9 89.1
4 4.750 473.6 494.01 20.4 14.8 85.2 50
8 2.360 0 0 0.0 14.8 85.2
10 2.000 430.5 457.14 26.6 19.9 80.1 40
12 1.700 0 0 0.0 19.9 80.1
16 1.180 0 0 0.0 19.9 80.1 30
18 1.000 0 0 0.0 19.9 80.1
20
20 0.850 0 0 0.0 19.9 80.1
30 0.600 0 0 0.0 19.9 80.1
10
35 0.500 0 0 0.0 19.9 80.1
40 0.425 337.1 355.47 18.4 23.5 76.5 0
50 0.300 0 0 0.0 23.5 76.5 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 23.5 76.5 Particle Diameter (mm)
80 0.180 0 0 0.0 23.5 76.5
100 0.150 0 0 0.0 23.5 76.5 Grain Size Distribution Curve
200 0.075 299.5 339.57 40.1 31.2 68.8 % Gravel: 14.836 D20: Cu: #VALUE!
Pan 366.2 725.08 358.9 100.0 0.0 % Sand: 16.321 D30: - Cc: #VALUE!
TOTAL: 521.3 % Fines: 68.843 D60: - So: #VALUE!
Fineness Modulus 1.310 GI: 12.870 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.17.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP4 - 0.5m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 33 27 21 19
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.3 10.58 11.97 12.3 10.29 10.42 10.45 10.37
Mass Can & Soil (Wet) MCMS (g) 18.3 18.94 60.46 60.55 24.30 24.15 24.39 24.04
Mass Can & Soil (Dry) MCDS (g) 15.9 16.44 44.14 44.08 19.20 19.10 19.22 18.95
Mass of Soil MS (g) 5.60 5.86 32.17 31.78 8.91 8.68 8.77 8.58
Mass of Water MW (g) 2.40 2.50 16.32 16.47 5.10 5.05 5.17 5.09
Water Content w (%) 42.9 42.7 50.7 51.8 57.24 58.18 58.95 59.32

Liquid Limit (LL or w L ) (%): 58 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 43 50 4 4

CH
Plasticity Index (PI) (%): 16 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 51 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.55 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.16 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70 y = -3.682ln(x) + 70.189
40
R² = 0.991
Dry Preparation Procedure B: Fall 30 25 0
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2821.5 3057 3289 3258 0 1.40
Mass in Grams Mold 1686 1686 1686 1686 0
Wet Soil 1135.5 1371 1603 1572 0 1.20
Wet Density , g/cc 1.20 1.45 1.70 1.67 0.00
Can Number 1 2 3 4 5 1.00
Can + Wet Soil (1) 60.26 60.26 60.58 60.52 0

Dry Unit Weight

Can + Dry Soil (1) 55.22 53.15 50.09 47.76 0 0.80
Mass in Grams Water (1) 5.04 7.11 10.49 12.76 0
Can (1) 18.1 22.02 18.57 18.86 0 0.60
Dry Soil (1) 37.1 31.13 31.52 28.9 0
Can + Wet Soil (2) 60.3 60.3 60.4 60.4 0.0 0.40
Can + Dry Soil (2) 55.0 52.9 50.1 47.9 0.0
Mass in Grams Water (2) 5.4 7.5 10.3 12.5 0.0 0.20
Can (2) 18.7 19.5 19.6 18.8 0.0
Dry Soil (2) 36.3 33.4 30.5 29.0 0.0 0.00
Water Content % 14.15% 22.59% 33.57% 43.65% #DIV/0! 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00% 50.00%
Dry Density g/cc 1.05 1.19 1.27 1.16 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.27 OMC (%): 33.57%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 0
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 4-0.5m Tested by : ROODNEY
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 4-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1107.44 0.000
0.254 0.003 2.75 17.45 1111.07 0.016 Unconfined Compression Test-TP4-0.5m
0.508 0.007 4.75 30.15 1114.73 0.027 0.070
0.762 0.010 7 44.43 1118.41 0.040
1.016 0.013 8.75 55.53 1122.11 0.049 0.060
1.524 0.020 10.75 68.23 1129.59 0.060
2.032 0.026 3.75 23.80 1137.17 0.021 0.050

Applied Stress, MPa

2.54 0.033 3 19.04 1144.86 0.017
3.048 0.039 3 19.04 1152.65 0.017 0.040
3.556 0.046 2.75 17.45 1160.54 0.015
4.064 0.052 2.75 17.45 1168.55 0.015 0.030
4.572 0.059 2.75 17.45 1176.66 0.015
5.08 0.065 2.75 17.45 1184.89 0.015 0.020
6.096 0.078 3.5 22.21 1201.70 0.018
7.112 0.092 2.5 15.87 1218.99 0.013 0.010
8.128 0.105 1.75 11.11 1236.79 0.009
9.144 0.118 0.5 3.17 1255.11 0.003
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.72 Unconfined Compression Test
Moist weight, g : 114.3 Diameter of sample: 37.56 Compressive strength, qu: 0.060 MPa
Oven-dry wt, g : 81.3 Area of sample: 1107.442 Undrained cohesion, cu: 0.121 MPa
Moisture content: 40.61 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Multuple fracturing
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP4 - 1.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 97.8 %
3/8" 97.8 %
No. 4 96.0 %
No. 10 90.6 %
No. 40 71.7 %
No. 200 62.8 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 66 %
Plastic Limit 38 %
Plasticity Index 28 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.17 g/cc
Optimum Moisture Content 31.36 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 4_1.0 M Wt. of Sample w/ Tare, g 568.3 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 500.6 D25 = - D60= -
Weight of Tare, g 67.7 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 516.66 11.1 2.2 97.8
60
3/8" 9.525 497.7 506.44 8.7 4.0 96.0
4 4.750 473.6 500.67 27.1 9.4 90.6 50
8 2.360 0 0 0.0 9.4 90.6
10 2.000 430.5 497.29 66.8 22.7 77.3 40
12 1.700 0 0 0.0 22.7 77.3
16 1.180 0 0 0.0 22.7 77.3 30
18 1.000 0 0 0.0 22.7 77.3
20
20 0.850 0 0 0.0 22.7 77.3
30 0.600 0 0 0.0 22.7 77.3
10
35 0.500 0 0 0.0 22.7 77.3
40 0.425 337.1 364.97 27.9 28.3 71.7 0
50 0.300 0 0 0.0 28.3 71.7 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 28.3 71.7 Particle Diameter (mm)
80 0.180 0 0 0.0 28.3 71.7
100 0.150 0 0 0.0 28.3 71.7 Grain Size Distribution Curve
200 0.075 299.5 344.22 44.7 37.2 62.8 % Gravel: 9.363 D20: Cu: #VALUE!
Pan 366.2 680.55 314.3 100.0 0.0 % Sand: 27.843 D30: - Cc: #VALUE!
TOTAL: 500.6 % Fines: 62.795 D60: - So: #VALUE!
Fineness Modulus 1.246 GI: 17.824 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.18.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP4 - 1.0m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 29 22 16
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.37 10.43 12.17 12.68 10.16 10.44 10.30 10.23
Mass Can & Soil (Wet) MCMS (g) 17.66 17.46 60.51 60.12 28.25 28.10 28.42 28.32
Mass Can & Soil (Dry) MCDS (g) 15.65 15.54 44.88 44.41 21.15 21.12 21.21 20.99
Mass of Soil MS (g) 5.28 5.11 32.71 31.73 10.99 10.68 10.91 10.76
Mass of Water MW (g) 2.01 1.92 15.63 15.71 7.10 6.98 7.21 7.33
Water Content w (%) 38.1 37.6 47.8 49.5 64.60 65.36 66.09 68.12

Liquid Limit (LL or w L ) (%): 66 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 38 50 4 4

CH
Plasticity Index (PI) (%): 28 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 49 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.39 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.46 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -4.358ln(x) + 79.972
40 R² = 0.9642

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2838.5 3133 3252.5 3171.5 0 1.20
Mass in Grams Mold 1686 1686 1686 1686 0
1.18
Wet Soil 1152.5 1447 1566.5 1485.5 0
Wet Density , g/cc 1.22 1.53 1.66 1.58 0.00 1.16
Can Number 1 2 3 4 5 1.14
Can + Wet Soil (1) 60.24 60.36 60.25 60.71 0

Dry Unit Weight

Can + Dry Soil (1) 53.56 50.56 48.03 45.91 0 1.12
Mass in Grams Water (1) 6.68 9.8 12.22 14.8 0 1.10
Can (1) 19.42 19.14 20.58 18.43 0
1.08
Dry Soil (1) 34.1 31.42 27.45 27.48 0
Can + Wet Soil (2) 60.4 60.3 60.5 60.3 0.0 1.06
Can + Dry Soil (2) 53.7 50.9 47.5 45.6 0.0 1.04
Mass in Grams Water (2) 6.7 9.4 13.0 14.7 0.0
Can (2) 1.02
21.5 21.1 18.7 19.2 0.0
Dry Soil (2) 32.2 29.8 28.8 26.4 0.0 1.00
Water Content % 20.22% 31.36% 44.83% 54.72% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.02 1.17 1.15 1.02 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.17 OMC (%): 31.36%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 4-1.0m Tested by : ROODNEY
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 4-1.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1113.94 0.000
0.254 0.003 2 12.69 1117.61 0.011 Unconfined Compression Test-TP4-1.0m
0.508 0.007 4.7 29.83 1121.31 0.027 0.090
0.762 0.010 8 50.77 1125.04 0.045 0.080
1.016 0.013 10.5 66.64 1128.79 0.059
1.524 0.020 14 88.86 1136.36 0.078 0.070
2.032 0.026 6.5 41.25 1144.04 0.036

Applied Stress, MPa

0.033 1151.82 0.060
2.54 3 19.04 0.017
3.048 0.039 3 19.04 1159.71 0.016 0.050
3.556 0.046 3 19.04 1167.71 0.016
4.064 0.053 3.25 20.63 1175.82 0.018 0.040
4.572 0.059 3.25 20.63 1184.04 0.017
0.030
5.08 0.066 3.25 20.63 1192.38 0.017
6.096 0.079 3 19.04 1209.41 0.016 0.020
7.112 0.092 2.75 17.45 1226.93 0.014
8.128 0.105 2.75 17.45 1244.98 0.014 0.010
9.144 0.118 2.5 15.87 1263.55 0.013
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.22333 Unconfined Compression Test
Moist weight, g : 109.0 Diameter of sample: 37.67 Compressive strength, qu: 0.078 MPa
Oven-dry wt, g : 76.9 Area of sample: 1113.938 Undrained cohesion, cu: 0.156 MPa
Moisture content: 41.78 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP4 - 1.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 99.6 %
3/8" 99.6 %
No. 4 98.8 %
No. 10 89.9 %
No. 40 55.1 %
No. 200 45.3 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.21 g/cc
Optimum Moisture Content 38.24 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION SM BROWNISH NON PLASTIC SILTY SAND

A-4

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 4_1.5 M Wt. of Sample w/ Tare, g 608.5 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 541.7 D25 = - D60= -
Weight of Tare, g 66.8 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 507.99 2.4 0.4 99.6
60
3/8" 9.525 497.7 501.67 4.0 1.2 98.8
4 4.750 473.6 522.16 48.6 10.1 89.9 50
8 2.360 0 0 0.0 10.1 89.9
10 2.000 430.5 545.92 115.4 31.4 68.6 40
12 1.700 0 0 0.0 31.4 68.6
16 1.180 0 0 0.0 31.4 68.6 30
18 1.000 0 0 0.0 31.4 68.6
20
20 0.850 0 0 0.0 31.4 68.6
30 0.600 0 0 0.0 31.4 68.6
10
35 0.500 0 0 0.0 31.4 68.6
40 0.425 337.1 410.24 73.1 44.9 55.1 0
50 0.300 0 0 0.0 44.9 55.1 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 44.9 55.1 Particle Diameter (mm)
80 0.180 0 0 0.0 44.9 55.1
100 0.150 0 0 0.0 44.9 55.1 Grain Size Distribution Curve
200 0.075 299.5 352.35 52.9 54.7 45.3 % Gravel: 10.138 D20: Cu: #VALUE!
Pan 366.2 611.57 245.4 100.0 0.0 % Sand: 44.565 D30: - Cc: #VALUE!
TOTAL: 541.7 % Fines: 45.296 D60: - So: #VALUE!
Fineness Modulus 1.742 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.21.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP4 - 1.5m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 12.82 11.98 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 60.96 60.25 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 45.83 44.64 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 33.01 32.66 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 15.13 15.61 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 45.8 47.8 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 47 CL
USCS Classification: 20 MH
SM 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILTY SAND 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3139 3348.5 3572.5 3506 0 1.24
Mass in Grams Mold 1991 1991 1991 1991 0
1.22
Wet Soil 1148 1357.5 1581.5 1515 0
Wet Density , g/cc 1.22 1.44 1.68 1.61 0.00 1.20
Can Number 1 2 3 4 5 1.18
Can + Wet Soil (1) 60.23 60.47 60.23 60.18 0

Dry Unit Weight

Can + Dry Soil (1) 54.42 52.26 49.44 47.42 0 1.16
Mass in Grams Water (1) 5.81 8.21 10.79 12.76 0 1.14
Can (1) 18.43 18.69 21.1 20.56 0
1.12
Dry Soil (1) 36.0 33.57 28.34 26.86 0
Can + Wet Soil (2) 60.4 60.3 60.3 60.4 0.0 1.10
Can + Dry Soil (2) 54.9 52.2 49.0 47.0 0.0 1.08
Mass in Grams Water (2) 5.5 8.1 11.3 13.4 0.0
Can (2) 1.06
19.4 19.1 19.7 19.2 0.0
Dry Soil (2) 35.5 33.1 29.3 27.8 0.0 1.04
Water Content % 15.83% 24.48% 38.24% 47.79% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.05 1.16 1.21 1.09 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.21 OMC (%): 38.24%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP4 - 2.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 99.9 %
No. 40 91.7 %
No. 200 82.3 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 52 %
Plastic Limit 37 %
Plasticity Index 15 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.22 g/cc
Optimum Moisture Content 36.34 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH GRAYISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 4_2.0 M Wt. of Sample w/ Tare, g 573.6 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 500 D25 = - D60= -
Weight of Tare, g 73.6 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.98 0.4 0.1 99.9 50
8 2.360 0 0 0.0 0.1 99.9
10 2.000 430.5 446.34 15.8 3.2 96.8 40
12 1.700 0 0 0.0 3.2 96.8
16 1.180 0 0 0.0 3.2 96.8 30
18 1.000 0 0 0.0 3.2 96.8
20
20 0.850 0 0 0.0 3.2 96.8
30 0.600 0 0 0.0 3.2 96.8
10
35 0.500 0 0 0.0 3.2 96.8
40 0.425 337.1 362.33 25.2 8.3 91.7 0
50 0.300 0 0 0.0 8.3 91.7 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 8.3 91.7 Particle Diameter (mm)
80 0.180 0 0 0.0 8.3 91.7
100 0.150 0 0 0.0 8.3 91.7 Grain Size Distribution Curve
200 0.075 299.5 346.47 47.0 17.7 82.3 % Gravel: 0.076 D20: Cu: #VALUE!
Pan 366.2 777.78 411.6 100.0 0.0 % Sand: 17.608 D30: - Cc: #VALUE!
TOTAL: 500.0 % Fines: 82.316 D60: - So: #VALUE!
Fineness Modulus 0.232 GI: 15.939 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.22.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP4 - 2.0m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 34 29 23 16
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.4 10.24 12.08 12.59 10.63 10.59 10.49 10.26
Mass Can & Soil (Wet) MCMS (g) 20.88 20.04 64.06 64.21 20.82 20.58 20.47 20.18
Mass Can & Soil (Dry) MCDS (g) 18.15 17.35 50.44 50.55 17.38 17.17 17.06 16.73
Mass of Soil MS (g) 7.75 7.11 38.36 37.96 6.75 6.58 6.57 6.47
Mass of Water MW (g) 2.73 2.69 13.62 13.66 3.44 3.41 3.41 3.45
Water Content w (%) 35.2 37.8 35.5 36.0 50.96 51.82 51.90 53.32

Liquid Limit (LL or w L ) (%): 52 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 37 50 4 4

CH
Plasticity Index (PI) (%): 15 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 36 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption GRAYISH ELASTIC SILT
0
Liquidity Index -0.05 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.44 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40
y = -2.885ln(x) + 61.237
Dry Preparation Procedure B: Fall 30 25 0 R² = 0.9332
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3150 3303 3562.5 3538 0 1.24
Mass in Grams Mold 1991 1991 1991 1991 0
1.22
Wet Soil 1159 1312 1571.5 1547 0
Wet Density , g/cc 1.23 1.39 1.67 1.64 0.00 1.20
Can Number 1 2 3 4 5 1.18
Can + Wet Soil (1) 60.47 60.29 60.19 60.3 0 1.16

Dry Unit Weight

Can + Dry Soil (1) 54.54 51.78 49.3 47.06 0
1.14
Mass in Grams Water (1) 5.93 8.51 10.89 13.24 0
Can (1) 20.61 19.15 19.24 18.42 0 1.12
Dry Soil (1) 33.9 32.63 30.06 28.64 0 1.10
Can + Wet Soil (2) 60.3 60.3 60.6 60.5 0.0 1.08
Can + Dry Soil (2) 54.3 51.9 49.4 48.0 0.0
1.06
Mass in Grams Water (2) 6.1 8.4 11.2 12.5 0.0
Can (2) 19.9 19.4 18.7 21.1 0.0 1.04
Dry Soil (2) 34.4 32.5 30.7 26.9 0.0 1.02
Water Content % 17.53% 26.00% 36.34% 46.31% #DIV/0! 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00% 45.00% 50.00%
Dry Density g/cc 1.05 1.10 1.22 1.12 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.22 OMC (%): 36.34%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 4-2.0m Tested by : ROODNEY
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 4-2.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1093.14 0.000
0.254 0.003 1.75 11.11 1096.80 0.010 Unconfined Compression Test-TP4-2.0m
0.508 0.007 3.5 22.21 1100.49 0.020 0.070
0.762 0.010 5.25 33.32 1104.20 0.030
1.016 0.013 6.75 42.84 1107.93 0.039 0.060
1.524 0.020 8.75 55.53 1115.48 0.050
2.032 0.027 10 63.47 1123.13 0.057 0.050

Applied Stress, MPa

2.54 0.033 11 69.82 1130.89 0.062
3.048 0.040 11.25 71.40 1138.76 0.063 0.040
3.556 0.047 10.75 68.23 1146.73 0.059
4.064 0.053 4 25.39 1154.82 0.022 0.030
4.572 0.060 2 12.69 1163.02 0.011
5.08 0.067 2 12.69 1171.34 0.011 0.020
6.096 0.080 3.25 20.63 1188.35 0.017
7.112 0.093 3.25 20.63 1205.85 0.017 0.010
8.128 0.107 2.25 14.28 1223.88 0.012
9.144 0.120 1.5 9.52 1242.46 0.008
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 76.08667 Unconfined Compression Test
Moist weight, g : 126.1 Diameter of sample: 37.32 Compressive strength, qu: 0.063 MPa
Oven-dry wt, g : 84.9 Area of sample: 1093.139 Undrained cohesion, cu: 0.125 MPa
Moisture content: 48.6 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Axial Splitting
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP5 - 0.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 100.0 %
No. 40 98.8 %
No. 200 94.8 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 77 %
Plastic Limit 39 %
Plasticity Index 38 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.12 g/cc
Optimum Moisture Content 38.68 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-6

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 5_0.5 M Wt. of Sample w/ Tare, g 670.7 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 547.2 D25 = - D60= -
Weight of Tare, g 123.5 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 430.61 0.1 0.0 100.0 40
12 1.700 0 0 0.0 0.0 100.0
16 1.180 0 0 0.0 0.0 100.0 30
18 1.000 0 0 0.0 0.0 100.0
20
20 0.850 0 0 0.0 0.0 100.0
30 0.600 0 0 0.0 0.0 100.0
10
35 0.500 0 0 0.0 0.0 100.0
40 0.425 337.1 343.44 6.3 1.2 98.8 0
50 0.300 0 0 0.0 1.2 98.8 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.2 98.8 Particle Diameter (mm)
80 0.180 0 0 0.0 1.2 98.8
100 0.150 0 0 0.0 1.2 98.8 Grain Size Distribution Curve
200 0.075 299.5 321.47 22.0 5.2 94.8 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 884.98 518.8 100.0 0.0 % Sand: 5.194 D30: - Cc: #VALUE!
TOTAL: 547.2 % Fines: 94.806 D60: - So: #VALUE!
Fineness Modulus 0.024 GI: 45.108 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 04.29.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP5 - 0.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 30 26 22 0
Can Number --- --- 1 2 1 2 1 2 3 0
Mass of Empty Can MC (g) 4.43 4.31 12.18 12.01 4.44 4.41 4.31 0.00
Mass Can & Soil (Wet) MCMS (g) 12.82 12.95 52.82 51.24 19.46 19.30 19.23 0.00
Mass Can & Soil (Dry) MCDS (g) 10.48 10.52 38.27 36.98 13.41 12.84 12.52 0.00
Mass of Soil MS (g) 6.05 6.21 26.09 24.97 8.97 8.43 8.21 0.00
Mass of Water MW (g) 2.34 2.43 14.55 14.26 6.05 6.46 6.71 0.00
Water Content w (%) 38.7 39.1 55.8 57.1 67.45 76.63 81.73 #DIV/0!

Liquid Limit (LL or w L ) (%): 77 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 39 50 4 4

CH
Plasticity Index (PI) (%): 38 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 56 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-6 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.46 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.52 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -45.62ln(x) + 223.54
40 R² = 0.9573

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3250.7 3348.6 3458.1 3522.6 3460.7 1.14
Mass in Grams Mold 1991 1991 1991 1991 1991
Wet Soil 1259.7 1357.6 1467.1 1531.6 1469.7 1.12
Wet Density , g/cc 1.34 1.44 1.56 1.62 1.56 1.10
Can Number 1 2 3 4 5
Can + Wet Soil (1) 54.13 54.37 54.31 54.08 54.85 1.08

Dry Unit Weight

Can + Dry Soil (1) 45.91 44.22 42.69 40.58 39.18 1.06
Mass in Grams Water (1) 8.22 10.15 11.62 13.5 15.67
Can (1) 12.32 12.36 12.39 12.02 12.67 1.04
Dry Soil (1) 33.6 31.86 30.3 28.56 26.51
1.02
Can + Wet Soil (2) 54.0 54.3 54.4 54.1 54.3
Can + Dry Soil (2) 45.7 44.1 42.5 41.3 38.6 1.00
Mass in Grams Water (2) 8.3 10.2 11.9 12.8 15.7
0.98
Can (2) 12.1 12.9 12.0 13.1 12.2
Dry Soil (2) 33.6 31.1 30.5 28.2 26.4 0.96
Water Content % 24.62% 32.31% 38.68% 46.31% 59.32% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.07 1.09 1.12 1.11 0.98 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.12 OMC (%): 38.68%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 5-0.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 5-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1127.38 0.000
0.254 0.003 1.8 11.42 1131.11 0.010 Unconfined Compression Test-TP5-0.5m
0.508 0.007 3.9 24.75 1134.86 0.022 0.045
0.762 0.010 6 38.08 1138.63 0.033 0.040
1.016 0.013 7 44.43 1142.43 0.039
1.524 0.020 3.5 22.21 1150.10 0.019 0.035
2.032 0.026 2.5 15.87 1157.88 0.014

Applied Stress, MPa

0.033 1165.77 0.030
2.54 1.2 7.62 0.007
3.048 0.040 1.1 6.98 1173.76 0.006 0.025
3.556 0.046 1.1 6.98 1181.86 0.006
4.064 0.053 1 6.35 1190.08 0.005 0.020
4.572 0.059 1 6.35 1198.41 0.005
0.015
5.08 0.066 1 6.35 1206.85 0.005
6.096 0.079 0.9 5.71 1224.11 0.005 0.010
7.112 0.092 1.5 9.52 1241.87 0.008
8.128 0.105 1.2 7.62 1260.15 0.006 0.005
9.144 0.119 1.1 6.98 1278.98 0.005
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.14667 Unconfined Compression Test
Moist weight, g : 118.4 Diameter of sample: 37.90 Compressive strength, qu: 0.039 MPa
Oven-dry wt, g : 88.0 Area of sample: 1127.384 Undrained cohesion, cu: 0.078 MPa
Moisture content: 34.59 Proving Ring Calibration Factor: 6.34682 Consistency: Soft
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

0 - 0.024 Very soft
0.024 - 0.048 Soft
Prepared By: Noted By: 0.048 - 0.096 Medium
0.096 - 0.192 Stiff
JESELL CHAVEZ LAUREN S. GERENTE, ME-1 0.192 - 0.383 Very stiff
Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader 1 Megapascal = 20,885.46 psf

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP5 - 1.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 100.0 %
No. 40 98.8 %
No. 200 94.7 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 54 %
Plastic Limit 28 %
Plasticity Index 25 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.15 g/cc
Optimum Moisture Content 43.16 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION CH BROWNISH HIGHLY PLASTIC CLAY

A-7-6

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 5_1.0 M Wt. of Sample w/ Tare, g 603.7 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 480 D25 = - D60= -
Weight of Tare, g 123.7 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 430.7 0.2 0.0 100.0 40
12 1.700 0 0 0.0 0.0 100.0
16 1.180 0 0 0.0 0.0 100.0 30
18 1.000 0 0 0.0 0.0 100.0
20
20 0.850 0 0 0.0 0.0 100.0
30 0.600 0 0 0.0 0.0 100.0
10
35 0.500 0 0 0.0 0.0 100.0
40 0.425 337.1 342.5 5.4 1.2 98.8 0
50 0.300 0 0 0.0 1.2 98.8 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.2 98.8 Particle Diameter (mm)
80 0.180 0 0 0.0 1.2 98.8
100 0.150 0 0 0.0 1.2 98.8 Grain Size Distribution Curve
200 0.075 299.5 319.4 19.9 5.3 94.7 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 820.7 454.5 100.0 0.0 % Sand: 5.312 D30: - Cc: #VALUE!
TOTAL: 480.0 % Fines: 94.688 D60: - So: #VALUE!
Fineness Modulus 0.024 GI: 28.273 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 04.30.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP5 - 1.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 32 27 23 0
Can Number --- --- 1 2 1 2 1 2 3 0
Mass of Empty Can MC (g) 10.18 10.29 12.65 11.96 4.44 4.31 4.27 0.00
Mass Can & Soil (Wet) MCMS (g) 21.1 21.16 52.65 51.3 17.81 17.63 17.40 0.00
Mass Can & Soil (Dry) MCDS (g) 18.68 18.8 36.16 35.11 12.40 12.16 11.94 0.00
Mass of Soil MS (g) 8.50 8.51 23.51 23.15 7.96 7.85 7.67 0.00
Mass of Water MW (g) 2.42 2.36 16.49 16.19 5.41 5.47 5.46 0.00
Water Content w (%) 28.5 27.7 70.1 69.9 67.96 69.68 71.19 #DIV/0!

Liquid Limit (LL or w L ) (%): 54 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 28 50 4 4

CH
Plasticity Index (PI) (%): 25 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 70 CL
USCS Classification: 20 MH
CH 0 0
AASHTO Classification: A-7-6 10 70 CL-ML
70 ML
BROWNISH HIGHLY
Soil Desciption PLASTIC CLAY 0
Liquidity Index 1.65 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index -0.59 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -9.759ln(x) + 101.81
40 R² = 0.9995

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.02.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP5 - 1.0m Tested by : JES
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2956.7 3240.4 3266.2 3199.8 3158.5 1.18
Mass in Grams Mold 1686 1686 1686 1686 1686
1.16
Wet Soil 1270.7 1554.4 1580.2 1513.8 1472.5
Wet Density , g/cc 1.35 1.65 1.68 1.61 1.56 1.14
Can Number 1 2 3 4 5 1.12
Can + Wet Soil (1) 58.1 58.48 58.28 58.47 58.89 1.10

Dry Unit Weight

Can + Dry Soil (1) 48.49 44.88 43.17 41.93 41.37
1.08
Mass in Grams Water (1) 9.61 13.6 15.11 16.54 17.52
Can (1) 12.47 13.11 12.29 12.33 12.43 1.06
Dry Soil (1) 36.0 31.77 30.88 29.6 28.94 1.04
Can + Wet Soil (2) 58.2 58.4 58.5 58.9 58.5 1.02
Can + Dry Soil (2) 48.3 44.5 43.4 42.0 41.3
1.00
Mass in Grams Water (2) 9.9 14.0 15.1 17.0 17.2
Can (2) 12.3 12.3 11.9 12.2 12.4 0.98
Dry Soil (2) 36.0 32.1 31.4 29.7 28.9 0.96
Water Content % 27.05% 43.16% 48.48% 56.50% 60.06% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.06 1.15 1.13 1.03 0.98 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.15 OMC (%): 43.16%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 5-1.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 5-1.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1145.90 0.000
0.254 0.003 0.1 0.63 1149.68 0.001 Unconfined Compression Test-TP5-1.0m
0.508 0.007 1.1 6.98 1153.47 0.006 0.020
0.762 0.010 2.2 13.96 1157.30 0.012
1.016 0.013 3.2 20.31 1161.15 0.017
1.524 0.020 3.5 22.21 1168.92 0.019 0.015
2.032 0.026 2.9 18.41 1176.80 0.016

Applied Stress, MPa

2.54 0.033 2 12.69 1184.78 0.011
0.039 1192.88 0.010
3.048 1.2 7.62 0.006
3.556 0.046 1.1 6.98 1201.08 0.006
4.064 0.053 1 6.35 1209.40 0.005
0.005
4.572 0.059 0.8 5.08 1217.84 0.004
5.08 0.066 0.8 5.08 1226.40 0.004
6.096 0.079 0.6 3.81 1243.87 0.003
0.000
7.112 0.092 0.4 2.54 1261.85 0.002
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
8.128 0.105 0.1 0.63 1280.36 0.000
9.144 0.118 0.1 0.63 1299.42 0.000
-0.005
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.4 Unconfined Compression Test
Moist weight, g : 112.7 Diameter of sample: 38.21 Compressive strength, qu: 0.019 MPa
Oven-dry wt, g : 82.9 Area of sample: 1145.903 Undrained cohesion, cu: 0.038 MPa
Moisture content: 35.89 Proving Ring Calibration Factor: 6.34682 Consistency: Very soft
Mode of Failure: Multiple fracturing
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP5 - 1.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 99.7 %
No. 40 97.4 %
No. 200 87.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.26 g/cc
Optimum Moisture Content 34.02 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 5_1.5 M Wt. of Sample w/ Tare, g 669.7 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 506.23 D25 = - D60= -
Weight of Tare, g 163.47 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 474.88 1.3 0.3 99.7 50
8 2.360 0 0 0.0 0.3 99.7
10 2.000 430.5 433.33 2.8 0.8 99.2 40
12 1.700 0 0 0.0 0.8 99.2
16 1.180 0 0 0.0 0.8 99.2 30
18 1.000 0 0 0.0 0.8 99.2
20
20 0.850 0 0 0.0 0.8 99.2
30 0.600 0 0 0.0 0.8 99.2
10
35 0.500 0 0 0.0 0.8 99.2
40 0.425 337.1 346.12 9.0 2.6 97.4 0
50 0.300 0 0 0.0 2.6 97.4 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 2.6 97.4 Particle Diameter (mm)
80 0.180 0 0 0.0 2.6 97.4
100 0.150 0 0 0.0 2.6 97.4 Grain Size Distribution Curve
200 0.075 299.5 351.18 51.7 12.8 87.2 % Gravel: 0.253 D20: Cu: #VALUE!
Pan 366.2 807.62 441.4 100.0 0.0 % Sand: 12.550 D30: - Cc: #VALUE!
TOTAL: 506.2 % Fines: 87.198 D60: - So: #VALUE!
Fineness Modulus 0.073 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.06.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP5 - 1.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 12.36 12.31 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 52.59 52.58 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 36.7 36.75 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 24.34 24.44 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 15.89 15.83 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 65.3 64.8 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 65 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.07.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP5 - 1.5m Tested by : JES
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3240.7 3588.3 3531.9 3497 0 1.40
Mass in Grams Mold 1991 1991 1991 1991 0
Wet Soil 1249.7 1597.3 1540.9 1506 0 1.20
Wet Density , g/cc 1.33 1.69 1.63 1.60 0.00
Can Number 1 2 3 4 5 1.00
Can + Wet Soil (1) 52.33 52.61 52.81 52.1 0

Dry Unit Weight

Can + Dry Soil (1) 44.48 44.11 39.27 37.8 0 0.80
Mass in Grams Water (1) 7.85 8.5 13.54 14.3 0
Can (1) 12.31 12.49 12.44 12.27 0 0.60
Dry Soil (1) 32.2 31.62 26.83 25.53 0
Can + Wet Soil (2) 52.7 52.7 52.4 52.2 0.0 0.40
Can + Dry Soil (2) 44.8 40.8 38.9 38.4 0.0
Mass in Grams Water (2) 8.0 11.9 13.4 13.9 0.0 0.20
Can (2) 12.4 11.9 12.3 12.3 0.0
Dry Soil (2) 32.3 28.9 26.6 26.0 0.0 0.00
Water Content % 24.53% 34.02% 50.46% 54.66% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.06 1.26 1.09 1.03 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.26 OMC (%): 34.02%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP5 - 2.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 98.9280245 %
3/8" 98.9 %
No. 4 98.8 %
No. 10 97.6 %
No. 40 93.6 %
No. 200 85.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.05 g/cc
Optimum Moisture Content 48.13 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.17.2019
Project: Camella Lima Date of Testing : 05.08.2019
Location: Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered: TP5 - 2.0m Tested by : JES
Delivered by: A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by: A.Catangue, J.Chavez, R.Ortal
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 5_2.0 M Wt. of Sample w/ Tare, g 650.55 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 489.75 D25 = - D60= -
Weight of Tare, g 160.8 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 510.85 5.3 1.1 98.9
60
3/8" 9.525 497.7 498.36 0.7 1.2 98.8
4 4.750 473.6 479.44 5.8 2.4 97.6 50
8 2.360 0 0 0.0 2.4 97.6
10 2.000 430.5 438.63 8.1 4.1 95.9 40
12 1.700 0 0 0.0 4.1 95.9
16 1.180 0 0 0.0 4.1 95.9 30
18 1.000 0 0 0.0 4.1 95.9
20
20 0.850 0 0 0.0 4.1 95.9
30 0.600 0 0 0.0 4.1 95.9
10
35 0.500 0 0 0.0 4.1 95.9
40 0.425 337.1 348.38 11.3 6.4 93.6 0
50 0.300 0 0 0.0 6.4 93.6 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 6.4 93.6 Particle Diameter (mm)
80 0.180 0 0 0.0 6.4 93.6
100 0.150 0 0 0.0 6.4 93.6 Grain Size Distribution Curve
200 0.075 299.5 340.64 41.1 14.8 85.2 % Gravel: 2.399 D20: Cu: #VALUE!
Pan 366.2 783.65 417.5 100.0 0.0 % Sand: 12.363 D30: - Cc: #VALUE!
TOTAL: 489.7 % Fines: 85.237 D60: - So: #VALUE!
Fineness Modulus 0.268 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.08.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP5 - 2.0m Tested by : JES
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3006.6 3195.2 3460.2 3441.1 0 1.06
Mass in Grams Mold 1991 1991 1991 1991 0
Wet Soil 1015.6 1204.2 1469.2 1450.1 0 1.04
Wet Density , g/cc 1.08 1.28 1.56 1.54 0.00 1.02
Can Number 1 2 3 4 5
Can + Wet Soil (1) 70.26 70.14 70.75 70.17 0 1.00

Dry Unit Weight

Can + Dry Soil (1) 62.11 57.28 53.95 51.35 0 0.98
Mass in Grams Water (1) 8.15 12.86 16.8 18.82 0
Can (1) 19.08 18.55 18.4 20.09 0 0.96
Dry Soil (1) 43.0 38.73 35.55 31.26 0
0.94
Can + Wet Soil (2) 70.8 70.4 70.5 70.6 0.0
Can + Dry Soil (2) 62.0 57.5 53.4 51.0 0.0 0.92
Mass in Grams Water (2) 8.8 13.0 17.1 19.6 0.0
0.90
Can (2) 18.4 18.9 18.6 19.9 0.0
Dry Soil (2) 43.6 38.6 34.8 31.1 0.0 0.88
Water Content % 19.58% 33.44% 48.13% 61.59% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 0.90 0.96 1.05 0.95 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 0
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.05 OMC (%): 48.13%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP6 - 0.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 100.0 %
No. 40 98.3 %
No. 200 94.3 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.22 g/cc
Optimum Moisture Content 38.73 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 6_0.5 M Wt. of Sample w/ Tare, g 724.6 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 560.37 D25 = - D60= -
Weight of Tare, g 164.23 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 432.47 2.0 0.4 99.6 40
12 1.700 0 0 0.0 0.4 99.6
16 1.180 0 0 0.0 0.4 99.6 30
18 1.000 0 0 0.0 0.4 99.6
20
20 0.850 0 0 0.0 0.4 99.6
30 0.600 0 0 0.0 0.4 99.6
10
35 0.500 0 0 0.0 0.4 99.6
40 0.425 337.1 344.77 7.7 1.7 98.3 0
50 0.300 0 0 0.0 1.7 98.3 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.7 98.3 Particle Diameter (mm)
80 0.180 0 0 0.0 1.7 98.3
100 0.150 0 0 0.0 1.7 98.3 Grain Size Distribution Curve
200 0.075 299.5 321.66 22.2 5.7 94.3 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 894.77 528.6 100.0 0.0 % Sand: 5.675 D30: - Cc: #VALUE!
TOTAL: 560.4 % Fines: 94.325 D60: - So: #VALUE!
Fineness Modulus 0.041 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.10.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP6 - 0.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 12.2 12.25 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 52.29 52.38 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 37.56 37.71 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 25.36 25.46 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 14.73 14.67 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 58.1 57.6 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 58 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3076 3275.5 3218 3192.5 0 1.24
Mass in Grams Mold 1686 1686 1686 1686 0
1.22
Wet Soil 1390 1589.5 1532 1506.5 0
Wet Density , g/cc 1.47 1.69 1.62 1.60 0.00 1.20
Can Number 1 2 3 4 5 1.18
Can + Wet Soil (1) 60.17 60.67 60.7 60.07 0 1.16

Dry Unit Weight

Can + Dry Soil (1) 52.54 48.88 47.59 45.54 0
1.14
Mass in Grams Water (1) 7.63 11.79 13.11 14.53 0
Can (1) 21.09 19.57 19.53 18 0 1.12
Dry Soil (1) 31.5 29.31 28.06 27.54 0 1.10
Can + Wet Soil (2) 60.6 60.5 60.1 60.3 0.0 1.08
Can + Dry Soil (2) 51.9 49.1 47.9 46.8 0.0
1.06
Mass in Grams Water (2) 8.6 11.4 12.2 13.5 0.0
Can (2) 18.9 18.4 22.1 21.5 0.0 1.04
Dry Soil (2) 33.0 30.7 25.8 25.3 0.0 1.02
Water Content % 25.21% 38.73% 47.01% 53.10% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.18 1.22 1.11 1.04 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.22 OMC (%): 38.73%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP6 - 1.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 99.8 %
No. 40 98.0 %
No. 200 94.3 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.13 g/cc
Optimum Moisture Content 40.41 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 6_1.0 M Wt. of Sample w/ Tare, g 666.71 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 525.53 D25 = - D60= -
Weight of Tare, g 141.18 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 474.76 1.2 0.2 99.8 50
8 2.360 0 0 0.0 0.2 99.8
10 2.000 430.5 434.53 4.0 1.0 99.0 40
12 1.700 0 0 0.0 1.0 99.0
16 1.180 0 0 0.0 1.0 99.0 30
18 1.000 0 0 0.0 1.0 99.0
20
20 0.850 0 0 0.0 1.0 99.0
30 0.600 0 0 0.0 1.0 99.0
10
35 0.500 0 0 0.0 1.0 99.0
40 0.425 337.1 342.56 5.5 2.0 98.0 0
50 0.300 0 0 0.0 2.0 98.0 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 2.0 98.0 Particle Diameter (mm)
80 0.180 0 0 0.0 2.0 98.0
100 0.150 0 0 0.0 2.0 98.0 Grain Size Distribution Curve
200 0.075 299.5 319.01 19.5 5.7 94.3 % Gravel: 0.221 D20: Cu: #VALUE!
Pan 366.2 861.57 495.4 100.0 0.0 % Sand: 5.518 D30: - Cc: #VALUE!
TOTAL: 525.5 % Fines: 94.261 D60: - So: #VALUE!
Fineness Modulus 0.065 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.14.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP6 - 1.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 0 0 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 12.22 12.8 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 52.7 52.67 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 37.69 38.66 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 25.47 25.86 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 15.01 14.01 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 58.9 54.2 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 57 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2939 3187.5 3180 3135.5 0 1.16
Mass in Grams Mold 1686 1686 1686 1686 0
1.14
Wet Soil 1253 1501.5 1494 1449.5 0
Wet Density , g/cc 1.33 1.59 1.58 1.54 0.00 1.12
Can Number 1 2 3 4 5 1.10
Can + Wet Soil (1) 60.17 60.92 60.46 60.81 0 1.08

Dry Unit Weight

Can + Dry Soil (1) 51.79 49.67 46.28 44.93 0
1.06
Mass in Grams Water (1) 8.38 11.25 14.18 15.88 0
Can (1) 18.41 20.63 18.86 18.69 0 1.04
Dry Soil (1) 33.4 29.04 27.42 26.24 0 1.02
Can + Wet Soil (2) 60.6 60.5 60.4 60.5 0.0 1.00
Can + Dry Soil (2) 52.4 48.2 46.6 45.4 0.0
0.98
Mass in Grams Water (2) 8.2 12.4 13.8 15.0 0.0
Can (2) 21.1 18.7 19.2 20.4 0.0 0.96
Dry Soil (2) 31.3 29.5 27.4 25.1 0.0 0.94
Water Content % 25.55% 40.41% 51.00% 60.28% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.06 1.13 1.05 0.96 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.13 OMC (%): 40.41%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP6 - 1.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 99.09355836 %
3/8" 99.1 %
No. 4 97.8 %
No. 10 94.2 %
No. 40 83.0 %
No. 200 74.0 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 63 %
Plastic Limit 41 %
Plasticity Index 22 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.21 g/cc
Optimum Moisture Content 35.43 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 6_1.5 M Wt. of Sample w/ Tare, g 626 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 559.33 D25 = - D60= -
Weight of Tare, g 66.67 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 510.67 5.1 0.9 99.1
60
3/8" 9.525 497.7 504.81 7.1 2.2 97.8
4 4.750 473.6 493.95 20.4 5.8 94.2 50
8 2.360 0 0 0.0 5.8 94.2
10 2.000 430.5 469.15 38.7 12.7 87.3 40
12 1.700 0 0 0.0 12.7 87.3
16 1.180 0 0 0.0 12.7 87.3 30
18 1.000 0 0 0.0 12.7 87.3
20
20 0.850 0 0 0.0 12.7 87.3
30 0.600 0 0 0.0 12.7 87.3
10
35 0.500 0 0 0.0 12.7 87.3
40 0.425 337.1 360.74 23.6 17.0 83.0 0
50 0.300 0 0 0.0 17.0 83.0 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 17.0 83.0 Particle Diameter (mm)
80 0.180 0 0 0.0 17.0 83.0
100 0.150 0 0 0.0 17.0 83.0 Grain Size Distribution Curve
200 0.075 299.5 350.12 50.6 26.0 74.0 % Gravel: 5.816 D20: Cu: #VALUE!
Pan 366.2 780.09 413.9 100.0 0.0 % Sand: 20.187 D30: - Cc: #VALUE!
TOTAL: 559.3 % Fines: 73.997 D60: - So: #VALUE!
Fineness Modulus 0.732 GI: 19.368 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.15.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP6 - 1.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 27 23 17
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 4.46 4.34 13.12 12.33 4.45 4.39 4.31 4.29
Mass Can & Soil (Wet) MCMS (g) 10.83 10.66 53.12 53.27 15.97 15.61 15.25 15.05
Mass Can & Soil (Dry) MCDS (g) 8.97 8.85 43.08 41.89 11.55 11.29 11.03 10.87
Mass of Soil MS (g) 4.51 4.51 29.96 29.56 7.10 6.90 6.72 6.58
Mass of Water MW (g) 1.86 1.81 10.04 11.38 4.42 4.32 4.22 4.18
Water Content w (%) 41.2 40.1 33.5 38.5 62.25 62.61 62.80 63.53

Liquid Limit (LL or w L ) (%): 63 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 41 50 4 4

CH
Plasticity Index (PI) (%): 22 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 36 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index -0.21 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.66 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -1.746ln(x) + 68.393
40 R² = 0.9693

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.16.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP6 - 1.5m Tested by : JES
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3005.5 3128 3304 3536 3496.5 1.40
Mass in Grams Mold 1991 1991 1991 1991 1991
Wet Soil 1014.5 1137 1313 1545 1505.5 1.20
Wet Density , g/cc 1.08 1.21 1.39 1.64 1.60
Can Number 1 2 3 4 5 1.00
Can + Wet Soil (1) 60.54 60.4 60.48 60.46 60.5

Dry Unit Weight

Can + Dry Soil (1) 54.82 51.82 49.36 49.32 46.54 0.80
Mass in Grams Water (1) 5.72 8.58 11.12 11.14 13.96
Can (1) 12.42 12.57 12.34 18.69 20.55 0.60
Dry Soil (1) 42.4 39.25 37.02 30.63 25.99
Can + Wet Soil (2) 60.4 60.5 60.7 60.4 60.5 0.40
Can + Dry Soil (2) 54.0 52.2 49.5 49.9 46.6
Mass in Grams Water (2) 6.4 8.3 11.2 10.5 13.9 0.20
Can (2) 12.5 12.3 12.3 19.4 21.1
Dry Soil (2) 41.5 39.9 37.2 30.5 25.5 0.00
Water Content % 14.45% 21.35% 30.10% 35.43% 54.16% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 0.94 0.99 1.07 1.21 1.04 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.21 OMC (%): 35.43%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 6-1.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 6-1.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1127.38 0.000
0.254 0.003 4 25.39 1131.08 0.022 Unconfined Compression Test-TP6-1.5m
0.508 0.007 6.1 38.72 1134.80 0.034 0.040
0.762 0.010 6 38.08 1138.55 0.033 0.035
1.016 0.013 0 0.00 1142.32 0.000
1.524 0.020 0 0.00 1149.94 0.000 0.030
2.032 0.026 0 0.00 1157.65 0.000

Applied Stress, MPa

0.033 1165.48 0.025
2.54 0 0.00 0.000
3.048 0.039 0 0.00 1173.41 0.000 0.020
3.556 0.046 0 0.00 1181.45 0.000
4.064 0.052 0 0.00 1189.60 0.000 0.015
4.572 0.059 0 0.00 1197.86 0.000
0.010
5.08 0.065 0 0.00 1206.24 0.000
6.096 0.078 0 0.00 1223.35 0.000 0.005
7.112 0.092 0 0.00 1240.96 0.000
8.128 0.105 0 0.00 1259.08 0.000 0.000
9.144 0.118 0 0.00 1277.73 0.000 0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
-0.005
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.71 Unconfined Compression Test
Moist weight, g : 84.9 Diameter of sample: 37.90 Compressive strength, qu: 0.034 MPa
Oven-dry wt, g : 63.4 Area of sample: 1127.384 Undrained cohesion, cu: 0.068 MPa
Moisture content: 33.9 Proving Ring Calibration Factor: 6.34682 Consistency: Soft
Mode of Failure: Axial Splitting
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP6 - 2.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 96.0 %
3/4" 96.0 %
1/2" 95.1 %
3/8" 95.1 %
No. 4 93.2 %
No. 10 81.9 %
No. 40 63.9 %
No. 200 50.8 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 59 %
Plastic Limit 47 %
Plasticity Index 12 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.14 g/cc
Optimum Moisture Content 38.62 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.17.2019
Project: Camella Lima Date of Testing : 05.20.2019
Location: Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered: TP6 - 2.0m Tested by : JES
Delivered by: A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by: A.Catangue, J.Chavez, R.Ortal
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 6_2.0 M Wt. of Sample w/ Tare, g 658.5 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 516.29 D25 = - D60= -
Weight of Tare, g 142.21 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 4.0 96.0
0.5" 12.7 505.6 510.37 4.8 4.9 95.1
60
3/8" 9.525 497.7 507.49 9.8 6.8 93.2
4 4.750 473.6 531.74 58.1 18.1 81.9 50
8 2.360 0 0 0.0 18.1 81.9
10 2.000 430.5 472.98 42.5 26.3 73.7 40
12 1.700 0 0 0.0 26.3 73.7
16 1.180 0 0 0.0 26.3 73.7 30
18 1.000 0 0 0.0 26.3 73.7
20
20 0.850 0 0 0.0 26.3 73.7
30 0.600 0 0 0.0 26.3 73.7
10
35 0.500 0 0 0.0 26.3 73.7
40 0.425 337.1 387.78 50.7 36.1 63.9 0
50 0.300 0 0 0.0 36.1 63.9 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 36.1 63.9 Particle Diameter (mm)
80 0.180 0 0 0.0 36.1 63.9
100 0.150 0 0 0.0 36.1 63.9 Grain Size Distribution Curve
200 0.075 299.5 367.03 67.5 49.2 50.8 % Gravel: 18.089 D20: Cu: #VALUE!
Pan 366.2 628.41 262.2 100.0 0.0 % Sand: 31.124 D30: - Cc: #VALUE!
TOTAL: 516.3 % Fines: 50.787 D60: - So: #VALUE!
Fineness Modulus 1.719 GI: 5.538 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP6 - 2.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 33 21 15 0
Can Number --- --- 1 2 0 0 1 2 3 0
Mass of Empty Can MC (g) 10.45 10.24 12.37 12.12 10.44 10.33 10.22 0.00
Mass Can & Soil (Wet) MCMS (g) 20.84 20.2 54.58 54.6 21.94 21.33 21.08 0.00
Mass Can & Soil (Dry) MCDS (g) 17.49 17.04 45.35 44.02 17.74 17.28 16.72 0.00
Mass of Soil MS (g) 7.04 6.80 32.98 31.90 7.30 6.95 6.50 0.00
Mass of Water MW (g) 3.35 3.16 9.23 10.58 4.20 4.05 4.36 0.00
Water Content w (%) 47.6 46.5 28.0 33.2 57.53 58.27 67.08 #DIV/0!

Liquid Limit (LL or w L ) (%): 59 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 47 50 4 4

CH
Plasticity Index (PI) (%): 12 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 31 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index -1.33 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.61 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40 y = -11.52ln(x) + 96.481
R² = 0.7371
Dry Preparation Procedure B: Fall 30 25 0
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.20.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP6 - 2.0m Tested by : JES
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3067 3276.5 3484 3457.5 3451.5 1.16
Mass in Grams Mold 1991 1991 1991 1991 1991
1.14
Wet Soil 1076 1285.5 1493 1466.5 1460.5
Wet Density , g/cc 1.14 1.36 1.58 1.56 1.55 1.12
Can Number 1 2 3 4 5 1.10
Can + Wet Soil (1) 68.57 68.24 68.74 68.8 68.77

Dry Unit Weight

Can + Dry Soil (1) 61.09 56.77 55.13 52.1 51.3 1.08
Mass in Grams Water (1) 7.48 11.47 13.61 16.7 17.47 1.06
Can (1) 18.97 18.58 19.57 18.41 18.71
1.04
Dry Soil (1) 42.1 38.19 35.56 33.69 32.59
Can + Wet Soil (2) 68.9 68.8 68.5 68.4 68.8 1.02
Can + Dry Soil (2) 61.4 58.3 54.6 52.4 51.5 1.00
Mass in Grams Water (2) 7.6 10.5 13.9 16.0 17.2
Can (2) 0.98
18.6 22.4 18.8 20.4 18.4
Dry Soil (2) 42.7 35.9 35.8 32.0 33.1 0.96
Water Content % 17.72% 29.62% 38.62% 49.86% 52.85% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 0.97 1.05 1.14 1.04 1.01 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.14 OMC (%): 38.62%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 6-2.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 6-2.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1126.39 0.000
0.254 0.003 1.5 9.52 1130.11 0.008 Unconfined Compression Test-TP6-2.0m
0.508 0.007 4.3 27.29 1133.84 0.024 0.045
0.762 0.010 6.9 43.79 1137.60 0.038 0.040
1.016 0.013 7.1 45.06 1141.39 0.039
1.524 0.020 7.1 45.06 1149.04 0.039 0.035
2.032 0.026 1.6 10.15 1156.80 0.009

Applied Stress, MPa

0.033 1164.66 0.030
2.54 1.9 12.06 0.010
3.048 0.039 1.5 9.52 1172.62 0.008 0.025
3.556 0.046 1.1 6.98 1180.70 0.006
4.064 0.053 1.1 6.98 1188.89 0.006 0.020
4.572 0.059 0.9 5.71 1197.19 0.005
0.015
5.08 0.066 0.9 5.71 1205.61 0.005
6.096 0.079 0.9 5.71 1222.81 0.005 0.010
7.112 0.092 0.9 5.71 1240.51 0.005
8.128 0.105 0.9 5.71 1258.73 0.005 0.005
9.144 0.118 0.9 5.71 1277.49 0.004
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.31 Unconfined Compression Test
Moist weight, g : 100.3 Diameter of sample: 37.88 Compressive strength, qu: 0.039 MPa
Oven-dry wt, g : 72.5 Area of sample: 1126.392 Undrained cohesion, cu: 0.079 MPa
Moisture content: 38.34 Proving Ring Calibration Factor: 6.34682 Consistency: Soft
Mode of Failure: Axial Splitting
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP7 - 0.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 100.0 %
No. 40 99.5 %
No. 200 92.4 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 48 %
Plastic Limit 33 %
Plasticity Index 15 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.22 g/cc
Optimum Moisture Content 39.84 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH LOW PLASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.17.2019
Project: Camella Lima Date of Testing : 05.20.2019
Location: Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered: TP7 - 0.5m Tested by : JES
Delivered by: A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by: A.Catangue, J.Chavez, R.Ortal
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 7_0.5 M Wt. of Sample w/ Tare, g 696 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 624.26 D25 = - D60= -
Weight of Tare, g 71.74 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.6 0.0 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 431.45 0.9 0.2 99.8 40
12 1.700 0 0 0.0 0.2 99.8
16 1.180 0 0 0.0 0.2 99.8 30
18 1.000 0 0 0.0 0.2 99.8
20
20 0.850 0 0 0.0 0.2 99.8
30 0.600 0 0 0.0 0.2 99.8
10
35 0.500 0 0 0.0 0.2 99.8
40 0.425 337.1 339.56 2.5 0.5 99.5 0
50 0.300 0 0 0.0 0.5 99.5 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 0.5 99.5 Particle Diameter (mm)
80 0.180 0 0 0.0 0.5 99.5
100 0.150 0 0 0.0 0.5 99.5 Grain Size Distribution Curve
200 0.075 299.5 343.49 44.0 7.6 92.4 % Gravel: 0.000 D20: Cu: #VALUE!
Pan 366.2 943.06 576.9 100.0 0.0 % Sand: 7.593 D30: - Cc: #VALUE!
TOTAL: 624.3 % Fines: 92.407 D60: - So: #VALUE!
Fineness Modulus 0.014 GI: 17.793 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.21.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP7 - 0.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 28 22 16
Can Number --- --- 1 2 0 0 1 2 3 4
Mass of Empty Can MC (g) 10.46 10.34 12.91 12.3 10.37 10.24 10.19 9.99
Mass Can & Soil (Wet) MCMS (g) 20.98 20.96 54.82 54.5 21.86 21.54 21.33 21.16
Mass Can & Soil (Dry) MCDS (g) 18.4 18.35 42.19 41.92 18.19 17.91 17.70 17.49
Mass of Soil MS (g) 7.94 8.01 29.28 29.62 7.82 7.67 7.51 7.50
Mass of Water MW (g) 2.58 2.61 12.63 12.58 3.67 3.63 3.63 3.67
Water Content w (%) 32.5 32.6 43.1 42.5 46.93 47.33 48.34 48.93

Liquid Limit (LL or w L ) (%): 48 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 33 50 4 4

CH
Plasticity Index (PI) (%): 15 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 43 CL
USCS Classification: 20
MH
ML 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
BROWNISH LOW PLASTIC
Soil Desciption SILT
0
Liquidity Index 0.67 07 10 7
20 30 40 50 60 70 80 90 100
Consistency Index 0.15 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0 y = -2.695ln(x) + 56.472

X Multipoint Cone 25 10 R² = 0.972
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.20.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP7 - 0.5m Tested by : JES
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3216 3457 3604.5 3553.5 3506.5 1.25
Mass in Grams Mold 1991 1991 1991 1991 1991
Wet Soil 1225 1466 1613.5 1562.5 1515.5
Wet Density , g/cc 1.30 1.55 1.71 1.66 1.61 1.20
Can Number 1 2 3 4 5
Can + Wet Soil (1) 68.36 68.21 68.49 68.92 68.28

Dry Unit Weight

Can + Dry Soil (1) 60.11 56.6 54.48 52.77 50.83 1.15
Mass in Grams Water (1) 8.25 11.61 14.01 16.15 17.45
Can (1) 18.53 18.95 18.61 18.96 18.6
1.10
Dry Soil (1) 41.6 37.65 35.87 33.81 32.23
Can + Wet Soil (2) 68.1 68.1 68.5 68.2 68.8
Can + Dry Soil (2) 59.9 56.5 54.6 52.1 52.2 1.05
Mass in Grams Water (2) 8.2 11.6 13.9 16.1 16.6
Can (2) 18.6 19.9 20.4 18.8 22.4
Dry Soil (2) 41.3 36.6 34.2 33.3 29.7 1.00
Water Content % 19.86% 31.26% 39.84% 48.01% 54.96% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.08 1.18 1.22 1.12 1.04 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.22 OMC (%): 39.84%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 7-0.5m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 7-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1100.18 0.000
0.254 0.003 0 0.00 1103.78 0.000 Unconfined Compression Test-TP7-0.5m
0.508 0.007 0 0.00 1107.40 0.000 0.018
0.762 0.010 0 0.00 1111.05 0.000 0.016
1.016 0.013 0.1 0.63 1114.72 0.001
1.524 0.020 0.1 0.63 1122.14 0.001 0.014
2.032 0.026 0.5 3.17 1129.66 0.003 0.012

Applied Stress, MPa

2.54 0.033 0.9 5.71 1137.27 0.005
0.039 1144.99 0.010
3.048 1.1 6.98 0.006
3.556 0.046 1.2 7.62 1152.82 0.007 0.008
4.064 0.052 1.8 11.42 1160.75 0.010
0.006
4.572 0.059 2 12.69 1168.80 0.011
5.08 0.065 2.1 13.33 1176.96 0.011 0.004
6.096 0.078 2.3 14.60 1193.61 0.012
0.002
7.112 0.091 2.9 18.41 1210.75 0.015
8.128 0.104 2.9 18.41 1228.39 0.015 0.000
9.144 0.117 2.8 17.77 1246.55 0.014 0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
-0.002
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.87667 Unconfined Compression Test
Moist weight, g : 132.0 Diameter of sample: 37.44 Compressive strength, qu: 0.015 MPa
Oven-dry wt, g : 89.0 Area of sample: 1100.181 Undrained cohesion, cu: 0.030 MPa
Moisture content: 48.41 Proving Ring Calibration Factor: 6.34682 Consistency: Very soft
Mode of Failure: Multiple fracturing
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP7 - 1.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 99.6 %
No. 40 98.3 %
No. 200 94.0 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 69 %
Plastic Limit 34 %
Plasticity Index 35 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.12 g/cc
Optimum Moisture Content 44.90 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 7_1.0 M Wt. of Sample w/ Tare, g 670.39 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 598.39 D25 = - D60= -
Weight of Tare, g 72 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 475.75 2.1 0.4 99.6 50
8 2.360 0 0 0.0 0.4 99.6
10 2.000 430.5 432.62 2.1 0.7 99.3 40
12 1.700 0 0 0.0 0.7 99.3
16 1.180 0 0 0.0 0.7 99.3 30
18 1.000 0 0 0.0 0.7 99.3
20
20 0.850 0 0 0.0 0.7 99.3
30 0.600 0 0 0.0 0.7 99.3
10
35 0.500 0 0 0.0 0.7 99.3
40 0.425 337.1 343.15 6.1 1.7 98.3 0
50 0.300 0 0 0.0 1.7 98.3 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 1.7 98.3 Particle Diameter (mm)
80 0.180 0 0 0.0 1.7 98.3
100 0.150 0 0 0.0 1.7 98.3 Grain Size Distribution Curve
200 0.075 299.5 325.06 25.6 6.0 94.0 % Gravel: 0.359 D20: Cu: #VALUE!
Pan 366.2 928.71 562.5 100.0 0.0 % Sand: 5.637 D30: - Cc: #VALUE!
TOTAL: 598.4 % Fines: 94.004 D60: - So: #VALUE!
Fineness Modulus 0.056 GI: 39.966 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.10.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP7 - 1.0m Tested by : Albert
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 28 23 19
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 9.98 10.5 12.68 12.44 4.33 4.30 4.52 4.41
Mass Can & Soil (Wet) MCMS (g) 18.84 19.49 54.77 54.82 16.31 16.64 16.45 16.96
Mass Can & Soil (Dry) MCDS (g) 16.63 17.22 41.61 39.47 11.47 11.65 11.58 11.83
Mass of Soil MS (g) 6.65 6.72 28.93 27.03 7.14 7.35 7.06 7.42
Mass of Water MW (g) 2.21 2.27 13.16 15.35 4.84 4.99 4.87 5.13
Water Content w (%) 33.2 33.8 45.5 56.8 67.79 67.89 68.98 69.14

Liquid Limit (LL or w L ) (%): 69 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 34 50 4 4

CH
Plasticity Index (PI) (%): 35 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 51 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.50 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.52 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -2.518ln(x) + 76.611
40 R² = 0.8682

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3201.5 3345 3519 3503.7 3443 1.20
Mass in Grams Mold 1991 1991 1991 1991 1991
Wet Soil 1210.5 1354 1528 1512.7 1452
1.00
Wet Density , g/cc 1.28 1.44 1.62 1.60 1.54
Can Number 1 2 3 4 5
Can + Wet Soil (1) 62.81 62.62 62.66 62.82 64.19 0.80

Dry Unit Weight

Can + Dry Soil (1) 50.99 48.09 45.47 43.61 42.28
Mass in Grams Water (1) 11.82 14.53 17.19 19.21 21.91 0.60
Can (1) 8.04 8.28 8.06 8.62 8.87
Dry Soil (1) 43.0 39.81 37.41 34.99 33.41
0.40
Can + Wet Soil (2) 62.6 62.3 62.2 62.9 64.7
Can + Dry Soil (2) 51.1 48.1 45.9 43.7 41.9
Mass in Grams Water (2) 11.5 14.2 16.3 19.2 22.7 0.20
Can (2) 8.7 8.2 8.8 8.3 8.0
Dry Soil (2) 42.3 39.9 37.1 35.4 33.9 0.00
Water Content % 27.39% 36.05% 44.90% 54.56% 66.29% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.01 1.06 1.12 1.04 0.93 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.12 OMC (%): 44.90%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 7-1.0m Tested by : ALBERT
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 7-1.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1129.37 0.000
0.254 0.003 0.8 5.08 1133.10 0.004 Unconfined Compression Test-TP7-1.0m
0.508 0.007 1.1 6.98 1136.85 0.006 0.070
0.762 0.010 1.9 12.06 1140.63 0.011
1.016 0.013 2.3 14.60 1144.44 0.013 0.060
1.524 0.020 3.1 19.68 1152.12 0.017
2.032 0.026 4.2 26.66 1159.92 0.023 0.050

Applied Stress, MPa

2.54 0.033 5.7 36.18 1167.81 0.031
3.048 0.040 7.1 45.06 1175.82 0.038 0.040
3.556 0.046 8.2 52.04 1183.93 0.044
4.064 0.053 9 57.12 1192.16 0.048 0.030
4.572 0.059 10.2 64.74 1200.50 0.054
5.08 0.066 11.1 70.45 1208.97 0.058 0.020
6.096 0.079 12 76.16 1226.25 0.062
7.112 0.092 5 31.73 1244.04 0.026 0.010
8.128 0.105 4.2 26.66 1262.35 0.021
9.144 0.119 4 25.39 1281.21 0.020
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.15667 Unconfined Compression Test
Moist weight, g : 136.3 Diameter of sample: 37.93 Compressive strength, qu: 0.062 MPa
Oven-dry wt, g : 90.0 Area of sample: 1129.368 Undrained cohesion, cu: 0.124 MPa
Moisture content: 51.53 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Axial Splitting
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP7 - 1.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 99.9 %
No. 10 99.8 %
No. 40 96.8 %
No. 200 89.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.08 g/cc
Optimum Moisture Content 38.37 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML BROWNISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 7_1.5 M Wt. of Sample w/ Tare, g 665.7 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 534.2 D25 = - D60= -
Weight of Tare, g 131.5 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 498.4 0.7 0.1 99.9
4 4.750 473.6 474.07 0.5 0.2 99.8 50
8 2.360 0 0 0.0 0.2 99.8
10 2.000 430.5 434.34 3.8 0.9 99.1 40
12 1.700 0 0 0.0 0.9 99.1
16 1.180 0 0 0.0 0.9 99.1 30
18 1.000 0 0 0.0 0.9 99.1
20
20 0.850 0 0 0.0 0.9 99.1
30 0.600 0 0 0.0 0.9 99.1
10
35 0.500 0 0 0.0 0.9 99.1
40 0.425 337.1 348.94 11.8 3.2 96.8 0
50 0.300 0 0 0.0 3.2 96.8 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 3.2 96.8 Particle Diameter (mm)
80 0.180 0 0 0.0 3.2 96.8
100 0.150 0 0 0.0 3.2 96.8 Grain Size Distribution Curve
200 0.075 299.5 340.46 41.0 10.8 89.2 % Gravel: 0.219 D20: Cu: #VALUE!
Pan 366.2 842.59 476.4 100.0 0.0 % Sand: 10.603 D30: - Cc: #VALUE!
TOTAL: 534.2 % Fines: 89.178 D60: - So: #VALUE!
Fineness Modulus 0.088 GI: #VALUE! SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP7 - 1.5m Tested by : Roodney
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 0 0 0 0
Mass of Empty Can MC (g) 0 0 12.09 12.06 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 54.52 54.49 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 41.45 41.17 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 29.36 29.11 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 13.07 13.32 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 44.5 45.8 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 45 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2824.5 3101 3185 3129.5 0 1.10
Mass in Grams Mold 1686 1686 1686 1686 0
1.08
Wet Soil 1138.5 1415 1499 1443.5 0
Wet Density , g/cc 1.21 1.50 1.59 1.53 0.00 1.06
Can Number 1 2 3 4 5 1.04
Can + Wet Soil (1) 60.65 60.33 60.15 60.34 0

Dry Unit Weight

Can + Dry Soil (1) 53.14 48.94 46.05 44.17 0 1.02
Mass in Grams Water (1) 7.51 11.39 14.1 16.17 0 1.00
Can (1) 21.17 19.3 19.09 20.57 0
0.98
Dry Soil (1) 32.0 29.64 26.96 23.6 0
Can + Wet Soil (2) 60.6 60.4 60.2 60.4 0.0 0.96
Can + Dry Soil (2) 52.5 48.8 46.2 43.9 0.0 0.94
Mass in Grams Water (2) 8.1 11.6 14.0 16.5 0.0
Can (2) 0.92
18.5 18.7 19.4 19.7 0.0
Dry Soil (2) 34.0 30.2 26.8 24.2 0.0 0.90
Water Content % 23.72% 38.37% 52.39% 68.32% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00% 80.00%
Dry Density g/cc 0.98 1.08 1.04 0.91 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.08 OMC (%): 38.37%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ROODNEY C. ORTAL, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP7 - 2.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

C. ATTERBERG LIMIT TEST

Liquid Limit NP %
Plastic Limit NP %
Plasticity Index NP %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.40 g/cc
Optimum Moisture Content 27.03 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION ML GRAYISH NON PLASTIC SILT

A-4

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 02.16.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP7 - 2.0m Tested by : Albert
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 0 0 0 0
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 0 0 11.93 12.44 0.00 0.00 0.00 0.00
Mass Can & Soil (Wet) MCMS (g) 0 0 59.92 59.65 0.00 0.00 0.00 0.00
Mass Can & Soil (Dry) MCDS (g) 0 0 51.76 52.85 0.00 0.00 0.00 0.00
Mass of Soil MS (g) 0.00 0.00 39.83 40.41 0.00 0.00 0.00 0.00
Mass of Water MW (g) 0.00 0.00 8.16 6.80 0.00 0.00 0.00 0.00
Water Content w (%) #DIV/0! #DIV/0! 20.5 16.8 #DIV/0! #DIV/0! #DIV/0! #DIV/0!

Liquid Limit (LL or w L ) (%): - 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): #DIV/0! 50 4 4

CH
Plasticity Index (PI) (%): ###### 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 19 CL
USCS Classification: 20 MH
ML 0 0
AASHTO Classification: A-4 10 70 CL-ML
70 ML
GRAYISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index #DIV/0! 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index ###### 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 02.21.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : TP7 - 2.0m Tested by : ALBERT
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit
MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)
ASTM D-1557

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3033 3236 3367 3266 0 1.44
Mass in Grams Mold 1686 1686 1686 1686 0
1.42
Wet Soil 1347 1550 1681 1580 0
Wet Density , g/cc 1.43 1.64 1.78 1.68 0.00 1.40
Can Number 1 2 3 4 5 1.38
Can + Wet Soil (1) 60.84 60.84 60.72 62.48 0 1.36

Dry Unit Weight

Can + Dry Soil (1) 56.52 53.07 50.41 49.68 0
1.34
Mass in Grams Water (1) 4.32 7.77 10.31 12.8 0
Can (1) 12.7 12.07 12.48 12.23 0 1.32
Dry Soil (1) 43.8 41 37.93 37.45 0 1.30
Can + Wet Soil (2) 60.3 61.0 60.9 62.3 0.0 1.28
Can + Dry Soil (2) 56.0 53.4 50.6 49.2 0.0
1.26
Mass in Grams Water (2) 4.3 7.6 10.3 13.1 0.0
Can (2) 12.2 12.7 12.1 12.0 0.0 1.24
Dry Soil (2) 43.8 40.7 38.5 37.2 0.0 1.22
Water Content % 9.84% 18.82% 27.03% 34.67% #DIV/0! 0.00% 5.00% 10.00% 15.00% 20.00% 25.00% 30.00% 35.00% 40.00%
Dry Density g/cc 1.30 1.38 1.40 1.24 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.40 OMC (%): 27.03%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP15 - 0.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 100 %
3/8" 100.0 %
No. 4 100.0 %
No. 10 100.0 %
No. 40 97.2 %
No. 200 93.1 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 63 %
Plastic Limit 38 %
Plasticity Index 25 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.25 g/cc
Optimum Moisture Content 31.85 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ALBERT CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 15_0.5 M Wt. of Sample w/ Tare, g 605.89 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 540.17 D25 = - D60= -
Weight of Tare, g 65.72 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 505.6 0.0 0.0 100.0
60
3/8" 9.525 497.7 497.7 0.0 0.0 100.0
4 4.750 473.6 473.7 0.1 0.0 100.0 50
8 2.360 0 0 0.0 0.0 100.0
10 2.000 430.5 430.95 0.4 0.1 99.9 40
12 1.700 0 0 0.0 0.1 99.9
16 1.180 0 0 0.0 0.1 99.9 30
18 1.000 0 0 0.0 0.1 99.9
20
20 0.850 0 0 0.0 0.1 99.9
30 0.600 0 0 0.0 0.1 99.9
10
35 0.500 0 0 0.0 0.1 99.9
40 0.425 337.1 351.43 14.3 2.8 97.2 0
50 0.300 0 0 0.0 2.8 97.2 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 2.8 97.2 Particle Diameter (mm)
80 0.180 0 0 0.0 2.8 97.2
100 0.150 0 0 0.0 2.8 97.2 Grain Size Distribution Curve
200 0.075 299.5 321.66 22.2 6.9 93.1 % Gravel: 0.019 D20: Cu: #VALUE!
Pan 366.2 869.33 503.1 100.0 0.0 % Sand: 6.839 D30: - Cc: #VALUE!
TOTAL: 540.2 % Fines: 93.143 D60: - So: #VALUE!
Fineness Modulus 0.058 GI: 30.118 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.10.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP15 - 0.5m Tested by : Albert
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 28 25 0
Can Number --- --- 1 2 1 2 1 2 3 0
Mass of Empty Can MC (g) 10.36 10.24 22.45 18.6 3.98 4.31 4.32 0.00
Mass Can & Soil (Wet) MCMS (g) 20.28 20.83 55.62 55.82 23.29 24.88 24.44 0.00
Mass Can & Soil (Dry) MCDS (g) 17.57 17.93 42.38 41.22 16.06 17.16 16.60 0.00
Mass of Soil MS (g) 7.21 7.69 19.93 22.62 12.08 12.85 12.28 0.00
Mass of Water MW (g) 2.71 2.90 13.24 14.60 7.23 7.72 7.84 0.00
Water Content w (%) 37.6 37.7 66.4 64.5 59.85 60.08 63.84 #DIV/0!

Liquid Limit (LL or w L ) (%): 63 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 38 50 4 4

CH
Plasticity Index (PI) (%): 25 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 65 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 1.11 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index -0.07 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70 y = -10.35ln(x) + 96.139
40
R² = 0.6248
Dry Preparation Procedure B: Fall 30 25 0
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2955.4 3061.2 3246.4 3342 3260.4 1.28
Mass in Grams Mold 1686 1686 1686 1686 1686
Wet Soil 1269.4 1375.2 1560.4 1656 1574.4 1.26
Wet Density , g/cc 1.35 1.46 1.65 1.76 1.67 1.24
Can Number 1 2 3 4 5
Can + Wet Soil (1) 62.01 63.93 62.31 67.79 65.63 1.22

Dry Unit Weight

Can + Dry Soil (1) 55.67 54.71 51.66 53.19 47.39 1.20
Mass in Grams Water (1) 6.34 9.22 10.65 14.6 18.24
Can (1) 18.56 18.82 18.85 18.54 10.23 1.18
Dry Soil (1) 37.1 35.89 32.81 34.65 37.16
1.16
Can + Wet Soil (2) 63.0 63.4 62.6 67.4 65.8
Can + Dry Soil (2) 56.3 55.3 53.0 53.8 47.7 1.14
Mass in Grams Water (2) 6.7 8.2 9.7 13.7 18.2
1.12
Can (2) 18.2 19.6 22.0 19.5 10.3
Dry Soil (2) 38.1 35.7 30.9 34.3 37.3 1.10
Water Content % 17.37% 24.33% 31.85% 41.00% 48.90% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.15 1.17 1.25 1.25 1.12 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.25 OMC (%): 31.85%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 15-0.5m Tested by : ALBERT
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 15-0.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1133.34 0.000
0.254 0.003 4 25.39 1137.07 0.022 Unconfined Compression Test-TP15-0.5m
0.508 0.007 8 50.77 1140.83 0.045 0.100
0.762 0.010 11 69.82 1144.61 0.061 0.090
1.016 0.013 14.8 93.93 1148.41 0.082
1.524 0.020 16.8 106.63 1156.10 0.092 0.080
2.032 0.026 16 101.55 1163.89 0.087 0.070

Applied Stress, MPa

2.54 0.033 10.8 68.55 1171.78 0.058
0.039 1179.79 0.060
3.048 9 57.12 0.048
3.556 0.046 8 50.77 1187.90 0.043 0.050
4.064 0.052 6.4 40.62 1196.13 0.034
0.040
4.572 0.059 5.6 35.54 1204.47 0.030
5.08 0.066 4.8 30.46 1212.93 0.025 0.030
6.096 0.079 3.8 24.12 1230.20 0.020
0.020
7.112 0.092 3.3 20.94 1247.98 0.017
8.128 0.105 3 19.04 1266.28 0.015 0.010
9.144 0.118 2.8 17.77 1285.12 0.014
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish elastic silt Length of sample: 77.42333 Unconfined Compression Test
Moist weight, g : 130.0 Diameter of sample: 38.00 Compressive strength, qu: 0.092 MPa
Oven-dry wt, g : 96.4 Area of sample: 1133.341 Undrained cohesion, cu: 0.184 MPa
Moisture content: 34.93 Proving Ring Calibration Factor: 6.34682 Consistency: Stiff
Mode of Failure: Multiple fracturing
REMARKS:

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP15 - 1.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 100 %
1/2" 98.1 %
3/8" 98.1 %
No. 4 97.5 %
No. 10 92.8 %
No. 40 80.7 %
No. 200 76.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 62 %
Plastic Limit 40 %
Plasticity Index 22 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.24 g/cc
Optimum Moisture Content 40.60 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION CH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 15_1.0 M Wt. of Sample w/ Tare, g 632.99 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 567.16 D25 = - D60= -
Weight of Tare, g 65.83 D30 = - D75= -

% Passing
0.75" 19.050 519.5 519.5 0.0 0.0 100.0
0.5" 12.7 505.6 516.59 11.0 1.9 98.1
60
3/8" 9.525 497.7 501.14 3.4 2.5 97.5
4 4.750 473.6 499.9 26.3 7.2 92.8 50
8 2.360 0 0 0.0 7.2 92.8
10 2.000 430.5 465.23 34.7 13.3 86.7 40
12 1.700 0 0 0.0 13.3 86.7
16 1.180 0 0 0.0 13.3 86.7 30
18 1.000 0 0 0.0 13.3 86.7
20
20 0.850 0 0 0.0 13.3 86.7
30 0.600 0 0 0.0 13.3 86.7
10
35 0.500 0 0 0.0 13.3 86.7
40 0.425 337.1 371.13 34.0 19.3 80.7 0
50 0.300 0 0 0.0 19.3 80.7 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 19.3 80.7 Particle Diameter (mm)
80 0.180 0 0 0.0 19.3 80.7
100 0.150 0 0 0.0 19.3 80.7 Grain Size Distribution Curve
200 0.075 299.5 325.21 25.7 23.8 76.2 % Gravel: 7.181 D20: Cu: #VALUE!
Pan 366.2 798.16 432.0 100.0 0.0 % Sand: 16.657 D30: - Cc: #VALUE!
TOTAL: 567.2 % Fines: 76.162 D60: - So: #VALUE!
Fineness Modulus 0.821 GI: 20.098 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP15 - 1.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 29 22 17
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 4.27 4.03 19.55 18.69 4.52 4.41 4.35 4.30
Mass Can & Soil (Wet) MCMS (g) 12.48 12.49 59.04 59.34 15.83 15.67 15.37 15.04
Mass Can & Soil (Dry) MCDS (g) 10.15 10.06 44.04 47.12 11.57 11.41 11.10 10.87
Mass of Soil MS (g) 5.88 6.03 24.49 28.43 7.05 7.00 6.75 6.57
Mass of Water MW (g) 2.33 2.43 15.00 12.22 4.26 4.26 4.27 4.17
Water Content w (%) 39.6 40.3 61.2 43.0 60.43 60.86 63.26 63.47

Liquid Limit (LL or w L ) (%): 62 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 40 50 4 4

CH
Plasticity Index (PI) (%): 22 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 52 CL
USCS Classification: 20 MH
CH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.55 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.25 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70 y = -4.756ln(x) + 77.278
40 R² = 0.9012

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 3271 3504.5 3636.5 3560 3518.5 1.40
Mass in Grams Mold 1991 1991 1991 1991 1991
Wet Soil 1280 1513.5 1645.5 1569 1527.5 1.20
Wet Density , g/cc 1.36 1.60 1.74 1.66 1.62
Can Number 1 2 3 4 5 1.00
Can + Wet Soil (1) 60.88 60.89 60.27 60.09 60.23

Dry Unit Weight

Can + Dry Soil (1) 53.33 51.19 48.22 47.48 45.18 0.80
Mass in Grams Water (1) 7.55 9.7 12.05 12.61 15.05
Can (1) 18.89 19.66 18.55 22.04 18.84 0.60
Dry Soil (1) 34.4 31.53 29.67 25.44 26.34
Can + Wet Soil (2) 60.9 60.7 60.7 60.4 60.5 0.40
Can + Dry Soil (2) 53.2 50.5 48.5 47.1 46.1
Mass in Grams Water (2) 7.7 10.3 12.2 13.3 14.3 0.20
Can (2) 19.1 18.0 18.5 19.6 21.5
Dry Soil (2) 34.2 32.5 30.0 27.5 24.6 0.00
Water Content % 22.23% 31.17% 40.60% 48.94% 57.67% 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.11 1.22 1.24 1.12 1.03 Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.24 OMC (%): 40.60%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 15-1.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 15-1.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1118.28 0.000
0.254 0.003 0.5 3.17 1121.97 0.003 Unconfined Compression Test-TP15-1.0m
0.508 0.007 2.1 13.33 1125.69 0.012 0.045
0.762 0.010 4.1 26.02 1129.43 0.023 0.040
1.016 0.013 6.2 39.35 1133.20 0.035
1.524 0.020 7.5 47.60 1140.81 0.042 0.035
2.032 0.026 6.9 43.79 1148.52 0.038

Applied Stress, MPa

0.033 1156.33 0.030
2.54 6.1 38.72 0.033
3.048 0.039 5 31.73 1164.26 0.027 0.025
3.556 0.046 3.8 24.12 1172.29 0.021
4.064 0.053 3.1 19.68 1180.44 0.017 0.020
4.572 0.059 1.8 11.42 1188.70 0.010
0.015
5.08 0.066 1.1 6.98 1197.07 0.006
6.096 0.079 1 6.35 1214.18 0.005 0.010
7.112 0.092 0.9 5.71 1231.79 0.005
8.128 0.105 1.1 6.98 1249.91 0.006 0.005
9.144 0.118 0.8 5.08 1268.58 0.004
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.18 Unconfined Compression Test
Moist weight, g : 103.8 Diameter of sample: 37.74 Compressive strength, qu: 0.042 MPa
Oven-dry wt, g : 75.0 Area of sample: 1118.279 Undrained cohesion, cu: 0.083 MPa
Moisture content: 38.43 Proving Ring Calibration Factor: 6.34682 Consistency: Medium strength
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP15 - 1.5m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 91.2 %
1/2" 88.6 %
3/8" 88.6 %
No. 4 85.0 %
No. 10 78.7 %
No. 40 69.1 %
No. 200 64.2 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 66 %
Plastic Limit 37 %
Plasticity Index 29 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.15 g/cc
Optimum Moisture Content 34.77 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH NON PLASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 15_1.5 M Wt. of Sample w/ Tare, g 679.9 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 521.85 D25 = - D60= -
Weight of Tare, g 158.05 D30 = - D75= -

% Passing
0.75" 19.050 519.5 565.42 45.9 8.8 91.2
0.5" 12.7 505.6 518.98 13.4 11.4 88.6
60
3/8" 9.525 497.7 516.9 19.2 15.0 85.0
4 4.750 473.6 506.4 32.8 21.3 78.7 50
8 2.360 0 0 0.0 21.3 78.7
10 2.000 430.5 458.2 27.7 26.6 73.4 40
12 1.700 0 0 0.0 26.6 73.4
16 1.180 0 0 0.0 26.6 73.4 30
18 1.000 0 0 0.0 26.6 73.4
20
20 0.850 0 0 0.0 26.6 73.4
30 0.600 0 0 0.0 26.6 73.4
10
35 0.500 0 0 0.0 26.6 73.4
40 0.425 337.1 359.48 22.4 30.9 69.1 0
50 0.300 0 0 0.0 30.9 69.1 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 30.9 69.1 Particle Diameter (mm)
80 0.180 0 0 0.0 30.9 69.1
100 0.150 0 0 0.0 30.9 69.1 Grain Size Distribution Curve
200 0.075 299.5 324.93 25.4 35.8 64.2 % Gravel: 21.328 D20: Cu: #VALUE!
Pan 366.2 701.24 335.0 100.0 0.0 % Sand: 14.470 D30: - Cc: #VALUE!
TOTAL: 521.8 % Fines: 64.202 D60: - So: #VALUE!
Fineness Modulus 1.816 GI: 18.792 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP15 - 1.5m Tested by : Albert
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 34 28 24 17
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.42 10.64 19.79 20.36 4.32 4.34 4.28 4.26
Mass Can & Soil (Wet) MCMS (g) 20.64 20.77 62.89 62.07 22.64 22.65 22.71 22.61
Mass Can & Soil (Dry) MCDS (g) 17.89 18 48.3 47.92 15.54 15.44 15.37 15.19
Mass of Soil MS (g) 7.47 7.36 28.51 27.56 11.22 11.10 11.09 10.93
Mass of Water MW (g) 2.75 2.77 14.59 14.15 7.10 7.21 7.34 7.42
Water Content w (%) 36.8 37.6 51.2 51.3 63.28 64.95 66.19 67.89

Liquid Limit (LL or w L ) (%): 66 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 37 50 4 4

CH
Plasticity Index (PI) (%): 29 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 51 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
BROWNISH NON PLASTIC
Soil Desciption SILT 0
Liquidity Index 0.49 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.39 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
y = -8.355ln(x) + 92.759
40 R² = 0.9995

Dry Preparation Procedure B: Fall 30 25 0

X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2946 3150 3212.5 3182.5 0 1.16
Mass in Grams Mold 1686 1686 1686 1686 0
Wet Soil 1260 1464 1526.5 1496.5 0 1.14
Wet Density , g/cc 1.34 1.55 1.62 1.59 0.00 1.12
Can Number 1 2 3 4 5
Can + Wet Soil (1) 62.8 61.96 60.99 61.68 0 1.10

Dry Unit Weight

Can + Dry Soil (1) 53.54 50.82 47.89 45.72 0 1.08
Mass in Grams Water (1) 9.26 11.14 13.1 15.96 0
Can (1) 18.59 18.62 18.98 18.52 0 1.06
Dry Soil (1) 35.0 32.2 28.91 27.2 0
1.04
Can + Wet Soil (2) 62.8 62.2 61.1 60.4 0.0
Can + Dry Soil (2) 54.0 51.4 48.0 44.8 0.0 1.02
Mass in Grams Water (2) 8.7 10.8 13.1 15.6 0.0
1.00
Can (2) 19.0 20.4 19.6 18.6 0.0
Dry Soil (2) 35.1 31.0 28.4 26.2 0.0 0.98
Water Content % 25.70% 34.77% 45.70% 59.04% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00% 70.00%
Dry Density g/cc 1.06 1.15 1.11 1.00 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.15 OMC (%): 34.77%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

ALBERT T. CATANGUE, CE LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.23.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 15-1.5m Tested by : ALBERT
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 15-1.5m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1130.76 0.000
0.254 0.003 3.2 20.31 1134.50 0.018 Unconfined Compression Test-TP15-1.5m
0.508 0.007 8 50.77 1138.27 0.045 0.120
0.762 0.010 12.3 78.07 1142.07 0.068
1.016 0.013 16.8 106.63 1145.89 0.093 0.100
1.524 0.020 19.5 123.76 1153.60 0.107
2.032 0.026 2 12.69 1161.42 0.011

Applied Stress, MPa

0.033 1169.35 0.080
2.54 2.2 13.96 0.012
3.048 0.040 2.5 15.87 1177.39 0.013
3.556 0.046 3 19.04 1185.54 0.016 0.060
4.064 0.053 3.5 22.21 1193.80 0.019
4.572 0.059 3.5 22.21 1202.18 0.018
0.040
5.08 0.066 3.5 22.21 1210.68 0.018
6.096 0.079 2.5 15.87 1228.03 0.013
7.112 0.092 2.5 15.87 1245.90 0.013 0.020
8.128 0.106 2.2 13.96 1264.29 0.011
9.144 0.119 0 0.00 1283.23 0.000
0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
Vertical Strain, mm/mm

Soil Description: Brownish non plastic silt Length of sample: 76.95667 Unconfined Compression Test
Moist weight, g : 118.8 Diameter of sample: 37.95 Compressive strength, qu: 0.107 MPa
Oven-dry wt, g : 91.3 Area of sample: 1130.758 Undrained cohesion, cu: 0.215 MPa
Moisture content: 30.12 Proving Ring Calibration Factor: 6.34682 Consistency: Very stiff
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

*Soil Investigation *Field Density Test
Upper Ground Floor, Worldwide Corporate Project 1, MGS Office, Molino IV, Bacoor , Cavite *Soil Particle Size Analysis *Mackintosh Probe Test
Center Contact No. (02) 226 3552
Shaw, Boulevard, 1552 Mandaluyong City, Local: 0566 *Atterberg Limit Test *Standard Classification of Soil
Metro Manila Cellphone No.: 0917-626-9380
Contact No. (02) 226 3552 Local: 0566
*Specific Gravity of Soil *Moisture Content Determination by
Calcium Carbide Test
*Standard Proctor Test
Client : Camella Communities, Inc.
Attention : Engr. Robert Comia Test Request Form No. : 4
Project : Camella Lima
Location : Malvar, Batangas
Sample Delivered : TP15 - 2.0m
Delivered by : A.Catangue, J.Chavez, R.Ortal
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit

SUMMARY OF TEST REPORT ON SOIL

A. UTILIZED SAMPLING PROCEDURE Quartering Method

B. SOIL PARTICLE SIZE ANALYSIS

Percent
Units
Sieve Size Passing
3" 100 %
2.5" 100 %
2" 100 %
1.5" 100 %
1" 100 %
3/4" 98.5 %
1/2" 96.0 %
3/8" 96.0 %
No. 4 93.0 %
No. 10 87.8 %
No. 40 72.6 %
No. 200 54.9 %
Diameter @ 10% Passing - mm
Diameter @ 30% Passing - mm
Diameter @ 50% Passing - mm
Diameter @ 60% Passing - mm
Uniformity Coefficient, Cu
Coefficient of Curvature, Cc - SAMPLE OF SOIL

C. ATTERBERG LIMIT TEST

Liquid Limit 57 %
Plastic Limit 48 %
Plasticity Index 9 %

D.1 SPECIFIC GRAVITY OF SOIL

Specific Gravity -

D.2 FREE SWELL INDEX OF SOIL - %

E. MOISTURE-DENSITY RELATION OF SOIL (COMPACTION TEST)

Maximum Dry Density 1.11 g/cc
Optimum Moisture Content 40.70 %

F. FIELD DENSITY TEST

Field Dry Density, g/cc - g/cc
In-situ Moisture Content, % - %
DEGREE OF COMPACTION - %

G. CALIFORNIA BEARING RATIO TEST

Designed CBR Value
Swelling Percentage, % %

H. UNCONFINED COMPRESSION STRENGTH MPa/ psi

H. SOIL CLASSIFICATION MH BROWNISH ELASTIC SILT

A-7-5

REMARKS:

Authorized Signatory:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

ENGR. RUBENSTEIN VALLO, CE

Geotechnical Team Head

GeoTech Team_Summary of Report on Soil

Client: Camella Communities, Inc. Test Request Form No. : 5

Attention: Engr. Robert Comia Date Received : 04.17.2019
Project: Camella Lima Date of Testing : 05.20.2019
Location: Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered: TP15 - 2.0m Tested by : JES
Delivered by: A.Catangue, J.Chavez, R.Ortal Checked by : LAUREN
Sampled by: A.Catangue, J.Chavez, R.Ortal
Source: Test Pit

SIEVE ANALYSIS TEST

ASTM D-422
Sample Identification: TP 15_2.0 M Wt. of Sample w/ Tare, g 645.77 D10 = - D50= - F Diameter sizes are
manually computed
Tare No. 1 Weight of Sample , g 500.39 D25 = - D60= -
Weight of Tare, g 145.38 D30 = - D75= -

% Passing
0.75" 19.050 519.5 527.05 7.5 1.5 98.5
0.5" 12.7 505.6 518.3 12.7 4.0 96.0
60
3/8" 9.525 497.7 512.48 14.8 7.0 93.0
4 4.750 473.6 499.52 25.9 12.2 87.8 50
8 2.360 0 0 0.0 12.2 87.8
10 2.000 430.5 457.24 26.7 17.5 82.5 40
12 1.700 0 0 0.0 17.5 82.5
16 1.180 0 0 0.0 17.5 82.5 30
18 1.000 0 0 0.0 17.5 82.5
20
20 0.850 0 0 0.0 17.5 82.5
30 0.600 0 0 0.0 17.5 82.5
10
35 0.500 0 0 0.0 17.5 82.5
40 0.425 337.1 386.62 49.5 27.4 72.6 0
50 0.300 0 0 0.0 27.4 72.6 10.000 1.000 0.100 0.010
60 0.250 0 0 0.0 27.4 72.6 Particle Diameter (mm)
80 0.180 0 0 0.0 27.4 72.6
100 0.150 0 0 0.0 27.4 72.6 Grain Size Distribution Curve
200 0.075 299.5 388.16 88.7 45.1 54.9 % Gravel: 12.180 D20: Cu: #VALUE!
Pan 366.2 640.72 274.5 100.0 0.0 % Sand: 32.958 D30: - Cc: #VALUE!
TOTAL: 500.4 % Fines: 54.861 D60: - So: #VALUE!
Fineness Modulus 1.228 GI: 5.272 SN: #VALUE!
REMARKS:
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Soil Test Request Form_Item B

Client : Camella Communities, Inc. Test Request # : 6

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.22.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered
: TP15 - 2.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal Source : Test Pit
LIQUID LIMIT, PLASTIC LIMIT TEST: ASTM D4318
TEST PLASTIC LIMIT MOIST. CONT. LIQUID LIMIT
NO
Variable 1 2 1 2 1 2 3 4
Var. Units
Number of Blows N blows 35 29 23 18
Can Number --- --- 1 2 1 2 1 2 3 4
Mass of Empty Can MC (g) 10.43 10.28 19.34 19.06 10.38 10.32 10.27 10.22
Mass Can & Soil (Wet) MCMS (g) 18.04 18.16 60.2 60.51 22.52 22.36 22.15 22.20
Mass Can & Soil (Dry) MCDS (g) 15.59 15.6 45.43 45.51 18.22 18.03 17.80 17.79
Mass of Soil MS (g) 5.16 5.32 26.09 26.45 7.84 7.71 7.53 7.57
Mass of Water MW (g) 2.45 2.56 14.77 15.00 4.30 4.33 4.35 4.41
Water Content w (%) 47.5 48.1 56.6 56.7 54.85 56.16 57.77 58.26

Liquid Limit (LL or w L ) (%): 57 60 LL PI U Line

A Line
Plasticity Index (PI)

Plastic Limit (PL or w P ) (%): 48 50 4 4

CH
Plasticity Index (PI) (%): 9 40 25.5 4
Activity of Clay: - 115.89 70
30
Moisture Content (%): 57 CL
USCS Classification: 20 MH
MH 0 0
AASHTO Classification: A-7-5 10 70 CL-ML
70 ML
Soil Desciption BROWNISH ELASTIC SILT
0
Liquidity Index 0.98 07 10 20
7 30 40 50 60 70 80 90 100
Consistency Index 0.00 29.6 7 Liquid Limit (LL or wL)

70
50 0
PROCEDURE USED 60 50 70
Water Content (%)

Wet Preparation Procedure A: 5015.8 7

Multipoint X Casagrande Cup 85.778 70
40 y = -5.258ln(x) + 73.78
R² = 0.9455
Dry Preparation Procedure B: Fall 30 25 0
X Multipoint Cone 25 10
20
25 20
REMARKS: 10 25 30
25 40
0 25 60
10 Number of Blows (N) 100

Note: Liquid limit is the moisture content

attains at 25 no. of blows
Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, CE

Geotechnical Laboratory Technician Geotechnical Lab Team Leader

GeoTech Team_Soil Test Request Form_Item C

Client : Camella Communities, Inc. Test Request Form No. : 8

Description of Materials:
Trial Number 1 2 3 4 5 MOISTURE-DENSITY RELATION (COMPACTION CURVE)
Mold + Wet Soil 2887.5 3162.5 3107 3125 0 1.12
Mass in Grams Mold 1686 1686 1686 1686 0
Wet Soil 1201.5 1476.5 1421 1439 0 1.10
Wet Density , g/cc 1.27 1.57 1.51 1.53 0.00
Can Number 1 2 3 4 5 1.08
Can + Wet Soil (1) 60.1 60.54 60.58 60.89 0

Dry Unit Weight

1.06
Can + Dry Soil (1) 52.52 48.63 46.71 45.35 0
Mass in Grams Water (1) 7.58 11.91 13.87 15.54 0 1.04
Can (1) 18.95 18.53 20.38 18.39 0
Dry Soil (1) 33.6 30.1 26.33 26.96 0 1.02
Can + Wet Soil (2) 60.0 60.2 60.8 60.8 0.0
1.00
Can + Dry Soil (2) 52.5 47.9 46.0 45.8 0.0
Mass in Grams Water (2) 7.5 12.3 14.7 15.0 0.0 0.98
Can (2) 19.5 18.6 18.5 18.8 0.0
Dry Soil (2) 33.0 29.3 27.5 26.9 0.0 0.96
Water Content % 22.62% 40.70% 53.08% 56.74% #DIV/0! 0.00% 10.00% 20.00% 30.00% 40.00% 50.00% 60.00%
Dry Density g/cc 1.04 1.11 0.98 0.97 #DIV/0! Water Content
Height , mm : 116.4 Blows/ Layer: 25 blows
Volume , cc : 943 No. of Layer: 3 layers MAX. DRY DENSITY: 1.11 OMC (%): 40.70%
Hammer Wt. Kg. : 4.54 Hammer Drop, mm : 457.2

REMARKS:

Prepared By: Noted By:

JESELL L. CHAVEZ LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item E

Client : Camella Communities, Inc. Test Request Form No. : 12

Attention : Engr. Robert Comia Date Received : 04.17.2019
Project : Camella Lima Date of Testing : 05.24.2019
Location : Malvar, Batangas Date of Report : 05.28.2019
Sample Delivered : Test Pit 15-2.0m Tested by : Jes
Delivered by : A.Catangue, J.Chavez, R.Ortal Checked by : Lauren
Sampled by : A.Catangue, J.Chavez, R.Ortal
Source : Test Pit 15-2.0m Note: Selection of Load is at maximum load or axial strain at 15%.
UNCONFINED COMPRESSIVE STRENGTH TEST
ASTM D2166
Sample Vertical Strain, Proving Ring dial Penetration Load, Corrected Area, Applied Stress,
Deformation, mm mm/mm reading, div N sqmm MPa
0 0.000 0 0.00 1119.66 0.000
0.254 0.003 2.8 17.77 1123.35 0.016 Unconfined Compression Test-TP15-2.0m
0.508 0.007 6.1 38.72 1127.06 0.034 0.070
0.762 0.010 9.2 58.39 1130.80 0.052
0.060
1.016 0.013 11.1 70.45 1134.57 0.062
1.524 0.020 10.9 69.18 1142.17 0.061
0.050
2.032 0.026 5 31.73 1149.87 0.028

Applied Stress, MPa

2.54 0.033 1.8 11.42 1157.68 0.010 0.040
3.048 0.039 0.9 5.71 1165.60 0.005
3.556 0.046 0.8 5.08 1173.62 0.004 0.030
4.064 0.053 0.3 1.90 1181.76 0.002
4.572 0.059 0.1 0.63 1190.01 0.001 0.020
5.08 0.066 0 0.00 1198.37 0.000
6.096 0.079 0 0.00 1215.46 0.000 0.010
7.112 0.092 0 0.00 1233.05 0.000
0.105 1251.14 0.000
8.128 0 0.00 0.000
0.000 2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 18.000
9.144 0.118 0 0.00 1269.78 0.000
-0.010
Vertical Strain, mm/mm

Soil Description: Brownish low plastic clay Length of sample: 77.34333 Unconfined Compression Test
Moist weight, g : 87.5 Diameter of sample: 37.77 Compressive strength, qu: 0.062 MPa
Oven-dry wt, g : 62.1 Area of sample: 1119.662 Undrained cohesion, cu: 0.124 MPa
Moisture content: 40.94 Proving Ring Calibration Factor: 6.34682 Consistency: Medium
Mode of Failure: Shearing along
REMARKS: single plane

Compr. Strength Consistency

GeoTech Team_Request Form_ Item E Page 8 of 10

Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila
Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 1 MPT # 2

MPT # 3 MPT # 4

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila
Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 5 MPT # 6

MPT # 7 MPT # 8

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 9 MPT # 10

MPT # 11 MPT # 12

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 13 MPT # 14

MPT # 15 MPT # 16

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 17 MPT # 18

MPT # 19 MPT # 20

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 21 MPT # 22

MPT # 23 MPT # 24

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 25 MPT # 26

MPT # 27 MPT # 28

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

PHOTOS: MACKINTOSH PROBE TESTING

MPT # 29 MPT # 30

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 1 DCPT # 2

DCPT # 3 DCPT # 4

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 5 DCPT # 6

DCPT # 7 DCPT # 8

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 9 DCPT # 10

DCPT # 11 DCPT # 12

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 13 DCPT # 14

DCPT # 15 DCPT # 16

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 17 DCPT # 18

DCPT # 19 DCPT # 20

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 21 DCPT # 22

DCPT # 23 DCPT # 24

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 25 DCPT # 26

DCPT # 27 DCPT # 28

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: DYNAMIC CONE PENETRATION TESTING

DCPT # 29 DCPT # 30

Tested by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader
Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: TEST PITS

TEST PIT # 1 TEST PIT # 2

TEST PIT # 3 TEST PIT # 4

Sampled by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item D Page 7 of 10

Upper Ground Floor, Worldwide
Project 1, MGS Office, Molino IV, Bacoor ,
Corporate Center
Cavite
Shaw, Boulevard, 1552
Contact No. (02) 226 3552
Mandaluyong City, Metro Manila Local: 0566
Contact No. (02) 226 3552
Cellphone No.: 0917-626-9380
Local: 0566

PHOTOS: TEST PITS

TEST PIT # 5 TEST PIT # 6

TEST PIT # 7 TEST PIT # 15

Sampled by: Noted By:

A. Catangue, J. Chavez, R. Ortal LAUREN S. GERENTE, ME-1

Geotechnical Laboratory Technician Geotechnical Laboratory Team Leader

GeoTech Team_Request Form_ Item D Page 7 of 10

4-Sty Residential Building With Roof Deck and No Basement, 60 Dagupan Street, San Francisco, Del Monte QC Final - Edited
No ratings yet
4-Sty Residential Building With Roof Deck and No Basement, 60 Dagupan Street, San Francisco, Del Monte QC Final - Edited
13 pages
Part 1 For Bypass
No ratings yet
Part 1 For Bypass
23 pages
Geotech Brgy Sabang
No ratings yet
Geotech Brgy Sabang
100 pages
Soiltest Report Listing
No ratings yet
Soiltest Report Listing
192 pages
Geotechnical Insights for Engineers
No ratings yet
Geotechnical Insights for Engineers
2 pages
Two Storey Hotel Building - Zafra
No ratings yet
Two Storey Hotel Building - Zafra
4 pages
Static Water Level (Metro Manila)
No ratings yet
Static Water Level (Metro Manila)
2 pages
Seismic Parameters: Brgy. Dela Paz Antipolo, Rizal
No ratings yet
Seismic Parameters: Brgy. Dela Paz Antipolo, Rizal
10 pages
DPWH Brgy. 227, Tondo, Manila
No ratings yet
DPWH Brgy. 227, Tondo, Manila
11 pages
Technological Institute of The Philippines 1338 Arlegui ST, Quiapo, Manila
No ratings yet
Technological Institute of The Philippines 1338 Arlegui ST, Quiapo, Manila
145 pages
Design Criteria - School Building
100% (1)
Design Criteria - School Building
2 pages
DESIGN OF APARTELLE BLDG (FOR STUDENTS) (Repaired)
No ratings yet
DESIGN OF APARTELLE BLDG (FOR STUDENTS) (Repaired)
71 pages
Structural Design Proposal Isabela
No ratings yet
Structural Design Proposal Isabela
2 pages
Leron's Structural Analysis
100% (1)
Leron's Structural Analysis
12 pages
Structural Analysis Sample
No ratings yet
Structural Analysis Sample
8 pages
Brgy. Pansol, Laguna
No ratings yet
Brgy. Pansol, Laguna
3 pages
RC 2 - Design Analysis and Design Criteria
No ratings yet
RC 2 - Design Analysis and Design Criteria
7 pages
Geotechnical Investigation Report
No ratings yet
Geotechnical Investigation Report
24 pages
1.0 Earthquake Load Combination: Strength Design
No ratings yet
1.0 Earthquake Load Combination: Strength Design
4 pages
Seismic Faults & Earthquake Basics
No ratings yet
Seismic Faults & Earthquake Basics
30 pages
5-Storey Building STAAD Analysis
No ratings yet
5-Storey Building STAAD Analysis
4 pages
Truss Analysis and Design
No ratings yet
Truss Analysis and Design
16 pages
Gutter Details Cross Bracing Conn. Detail: Office of The District Engineer
No ratings yet
Gutter Details Cross Bracing Conn. Detail: Office of The District Engineer
4 pages
Wind Load Design Guide
No ratings yet
Wind Load Design Guide
10 pages
Mapúa Wi-Fi Troubleshooting Guide
No ratings yet
Mapúa Wi-Fi Troubleshooting Guide
6 pages
Structural Notes: Typ. CHB Partition On Suspended Slab 7
No ratings yet
Structural Notes: Typ. CHB Partition On Suspended Slab 7
1 page
Canteen 3-2-19
No ratings yet
Canteen 3-2-19
41 pages
Bearing Capacity
No ratings yet
Bearing Capacity
20 pages
8 PIECES 16 Mm. Diameter Vertical Bars: 10 Mm. Lateral Ties SPACED 5 at 50 MM, 7 at 100 MM, REST at 150 MM O.C
No ratings yet
8 PIECES 16 Mm. Diameter Vertical Bars: 10 Mm. Lateral Ties SPACED 5 at 50 MM, 7 at 100 MM, REST at 150 MM O.C
1 page
208.4.4.3 Seismic Zone 4 Near-Source Factor
No ratings yet
208.4.4.3 Seismic Zone 4 Near-Source Factor
1 page
Sample Plumbing Works
No ratings yet
Sample Plumbing Works
6 pages
Proposed 3 (Three) Storey Residential Apartment Building
No ratings yet
Proposed 3 (Three) Storey Residential Apartment Building
24 pages
Enp n1196 Narvacan - Sulvec
No ratings yet
Enp n1196 Narvacan - Sulvec
49 pages
Rosales Spiral Stairs Plan
No ratings yet
Rosales Spiral Stairs Plan
3 pages
Soil Report Manila 1
No ratings yet
Soil Report Manila 1
21 pages
Proposed Two Storey Apartment Bldg. Steel Design
No ratings yet
Proposed Two Storey Apartment Bldg. Steel Design
3 pages
CE133-4 - LEC13 - Compression Perpendicular and Angle To Grain PDF
No ratings yet
CE133-4 - LEC13 - Compression Perpendicular and Angle To Grain PDF
16 pages
Assessment and Mitigation of Earthquake-Induced Landslides in Philippine Infrastructure
No ratings yet
Assessment and Mitigation of Earthquake-Induced Landslides in Philippine Infrastructure
4 pages
Wind Load
0% (1)
Wind Load
10 pages
Sealbond 218 P Pressure Injection Epoxy
0% (1)
Sealbond 218 P Pressure Injection Epoxy
1 page
NSCP Earthquake, Soil, Rain Code
67% (6)
NSCP Earthquake, Soil, Rain Code
41 pages
ANNEX 1 Topography and Hazard Map
No ratings yet
ANNEX 1 Topography and Hazard Map
6 pages
Narra Park Residences by Nurtura Land & Home - Oct 8 2015
0% (1)
Narra Park Residences by Nurtura Land & Home - Oct 8 2015
38 pages
Structural Design Blueprint
No ratings yet
Structural Design Blueprint
3 pages
Golden Home uPVC Brochure
No ratings yet
Golden Home uPVC Brochure
8 pages
Geographic Setting
No ratings yet
Geographic Setting
16 pages
Wind Load Analysis for 3-Storey Building
No ratings yet
Wind Load Analysis for 3-Storey Building
29 pages
Construction of Covered Court-S
No ratings yet
Construction of Covered Court-S
1 page
Fdjjsdbfdmxvbjds
No ratings yet
Fdjjsdbfdmxvbjds
3 pages
NSCP 2010
88% (8)
NSCP 2010
758 pages
Geoevaluation Report - Mr. - Mrs. Anthony Edward Garcia (Final Report)
No ratings yet
Geoevaluation Report - Mr. - Mrs. Anthony Edward Garcia (Final Report)
15 pages
Esperanza-MISA-OR For Design audit-EDITED BY MABS and Lon
No ratings yet
Esperanza-MISA-OR For Design audit-EDITED BY MABS and Lon
43 pages
Matest Geotechnical Report (Part 1)
No ratings yet
Matest Geotechnical Report (Part 1)
39 pages
Manila Batangas Bypass Soil Report
No ratings yet
Manila Batangas Bypass Soil Report
75 pages
Chapter 5 Geotech Report PDF
No ratings yet
Chapter 5 Geotech Report PDF
28 pages
109 Baguio
No ratings yet
109 Baguio
2 pages
Proposed Mixed Use BLDG
No ratings yet
Proposed Mixed Use BLDG
57 pages
Soil Investigation Report 1
No ratings yet
Soil Investigation Report 1
35 pages
Geotechnical Engg Final Report
No ratings yet
Geotechnical Engg Final Report
13 pages
Nabhaka Tolama Bhola Mandalko Ghar Dekhi Purb Janaki Mandir Sammsadak Dhalan Karya
No ratings yet
Nabhaka Tolama Bhola Mandalko Ghar Dekhi Purb Janaki Mandir Sammsadak Dhalan Karya
10 pages
dd-12 Folder
No ratings yet
dd-12 Folder
6 pages
Ground Investigation Summary
No ratings yet
Ground Investigation Summary
105 pages
Thesis F
No ratings yet
Thesis F
7 pages
Departmentorder Subject Revised Schedule of Fees and Charges For Laboratory Testing of Construction Materials
No ratings yet
Departmentorder Subject Revised Schedule of Fees and Charges For Laboratory Testing of Construction Materials
18 pages
Ground Improvement Techniques Guide
No ratings yet
Ground Improvement Techniques Guide
20 pages
Civil Engineering Lab Guide
No ratings yet
Civil Engineering Lab Guide
185 pages
56 - Effect of Slag On Stabilization of Sewage Sludge and Organic Soil
No ratings yet
56 - Effect of Slag On Stabilization of Sewage Sludge and Organic Soil
19 pages
Rigid Pavements and Necessity of Using Crushed Sand
No ratings yet
Rigid Pavements and Necessity of Using Crushed Sand
75 pages
AS 3798 2007 Guidelines On Earthworks For Commercial and Residential Developments.
No ratings yet
AS 3798 2007 Guidelines On Earthworks For Commercial and Residential Developments.
49 pages
Astm D6913 Test Method
No ratings yet
Astm D6913 Test Method
6 pages
Compaction Test Report
91% (22)
Compaction Test Report
5 pages
Method Statement Excavation Backfilling
No ratings yet
Method Statement Excavation Backfilling
16 pages
Geotechnics For Roads
No ratings yet
Geotechnics For Roads
321 pages
Vibratory Hammer Specs TG2
No ratings yet
Vibratory Hammer Specs TG2
3 pages
Design and Construction of Embankment Dams
100% (3)
Design and Construction of Embankment Dams
33 pages
As 1289.0-2000 Methods of Testing Soils For Engineering Purposes General Requirements and List of Methods
No ratings yet
As 1289.0-2000 Methods of Testing Soils For Engineering Purposes General Requirements and List of Methods
9 pages
Drainage Handbook ADH1 (02-17) PDF
No ratings yet
Drainage Handbook ADH1 (02-17) PDF
52 pages
Almeda ME Question Reviewer Joy
No ratings yet
Almeda ME Question Reviewer Joy
24 pages
Soil Works For Road Construction
No ratings yet
Soil Works For Road Construction
40 pages
NCT S.A. Composite Structures Catalog
No ratings yet
NCT S.A. Composite Structures Catalog
68 pages
Soil Mechanics for Civil Engineers
No ratings yet
Soil Mechanics for Civil Engineers
5 pages
Is Light Compaction Test
No ratings yet
Is Light Compaction Test
3 pages
Pokhara Sub-Metropolitan City Office Pokhara, Kaski: Rate Analysis Road Works (069/70)
No ratings yet
Pokhara Sub-Metropolitan City Office Pokhara, Kaski: Rate Analysis Road Works (069/70)
13 pages
2-05 Experimental Study
No ratings yet
2-05 Experimental Study
8 pages
Highway Construction Guide
100% (1)
Highway Construction Guide
11 pages
Soil Compaction
No ratings yet
Soil Compaction
3 pages
Geotechnical Review: St. Cloud VA Expansion
No ratings yet
Geotechnical Review: St. Cloud VA Expansion
24 pages
Lecture 5 - Soil Compaction
No ratings yet
Lecture 5 - Soil Compaction
33 pages
Prince Faisal Bin Sultan Palace: Riyadh - Saudi Arabia
No ratings yet
Prince Faisal Bin Sultan Palace: Riyadh - Saudi Arabia
10 pages