1891 Rodio LED - symmetric wide beam

Housing: in die-cast aluminium with cooling fins.

Reflector: in PMMA, highly resistant to temperature and UV radiation.
Diffuser: 5mm thick tempered glass, resistant to thermal shocks and impacts.
Coating: the standard powder coating consists of a first metal surface pre-
treatment stage and of single layer of UV-stabilised, corrosion and salt
resistant polyester powder coating.
Equipment: external connector for quick installation. Silicone rubber gasket;
external screws and bolts in stainless steel; air recirculation valve. Electronic
safety device to protect the LED module and the related ballast compliant with
EN 61547. It works in two modes: - differential mode: surge between power
cables and between the phase and neutral. - common mode: surge between
power, L/N and ground cables or between the fixture’s body if it is of class II
and installed on a metal pole. Upon request: protection up to 10KV. coating
compliant with UNI EN ISO 9227 Corrosion tests in artificial atmospheres for
aggressive environments.  Power factor: >= 0.9
Luminous flux maintenance  80%: 80000h (L80B20)
Wind surface: L:390cm² F:1420cm².
The fixtures can be equipped with a two-level dimming system that can be
preset and based on the calculation of the virtual midnight. The device is
embedded directly into the device and does not require the installer to update
the system.The dimming of the luminous flux occurs without a drive cable or a
control phase.
The average value between the time the lighting fixture is turned on (sunset)
and turned off (dawn) is the reference point for the device, and is called
“natural midnight”. A microprocessor will calculate the desired switching time
starting from this base value. Factory settings are 3 hours before the “natural
midnight” (approximately 10 pm) and 4 hours after it (approximately 5 am).
Factory settings may be changed upon special requests.

Download
DXF 2D
- 1891i.dxf

3DS
- disano_1891_rodio_36_led.3ds
- disano_1891_rodio_24_led.3ds

3DM
- disano_1891_rodio_36_led.3dm
- disano_1891_rodio_24_led.3dm

Montaggi
- rodio 12-21.pdf

BIM
- 1891 Rodio LED - symetric wide
beam - 20200528.zip

Code Gear Kg Lumen Output-K-CRI WTot Colour Surge

414784-00 CLD 5.96 LED-8627lm-4000K-CRI 80 53 W GRAPHITE 6/8kV
414785-00 CLD 6.07 LED-11561lm-4000K-CRI 80 79 W GRAPHITE 6/8kV
414786-00 CLD 6.14 LED-16881lm-4000K-CRI 80 118 W GRAPHITE 6/8kV
414787-00 CLD 5.88 LED-21140lm-4000K-CRI 80 157 W GRAPHITE 4/8kV
414784-39 CLD 5.84 LED-8023lm-3000K-CRI 80 53 W GRAPHITE 6/8kV
414785-39 CLD 5.87 LED-10752lm-3000K-CRI 80 79 W GRAPHITE 6/8kV
414786-39 CLD 6.11 LED-15699lm-3000K-CRI 80 118 W GRAPHITE 6/8kV
414787-39 CLD 6.60 LED-19660lm-3000K-CRI 80 157 W GRAPHITE 4/8kV

Accessories

- 333 pole mounting diam.60 - 334 pole mounting diam. 76 - 350 protection guard - Rodio

The reported luminous flux is the

flux emitted by the light source with
a tolerance of ± 10% compared to
the indicated value. The W tot
column indicates the total wattage
absorbed by the system without
exceeding 10% of the indicated

18/11/2022 Contact the Consulting and design Centre for any lighting information. PAG 1 - ENG