Scribd
Upload
1K views5 pages

Fahim Sadik Report 04 On Experiment-5

This lab report summarizes an experiment on studying clipping circuits using diodes. The objectives were to study diode applications in clipping circuits. The experiment used a function generator, oscilloscope, DC power supply, breadboard, diodes and resistors. Clipping circuits use diodes to clip away part of an input signal without distorting the remaining part. The experiment studied series and parallel, positive and negative clipping circuits and how a biased voltage can control the amount of voltage passed through the diode. The results showed how the diodes clip the input voltage based on their position in the circuit. Pictures show the input sine wave and outputs of biased series negative and positive clipping.

Uploaded by

Sadikul Hasan Mridha Atul (181016024)
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views5 pages

Fahim Sadik Report 04 On Experiment-5

This lab report summarizes an experiment on studying clipping circuits using diodes. The objectives were to study diode applications in clipping circuits. The experiment used a function generator, oscilloscope, DC power supply, breadboard, diodes and resistors. Clipping circuits use diodes to clip away part of an input signal without distorting the remaining part. The experiment studied series and parallel, positive and negative clipping circuits and how a biased voltage can control the amount of voltage passed through the diode. The results showed how the diodes clip the input voltage based on their position in the circuit. Pictures show the input sine wave and outputs of biased series negative and positive clipping.

Uploaded by

Sadikul Hasan Mridha Atul (181016024)
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

UNIVERSITY OF LIBERAL

ARTS BANGLADESH
COURSE TITLE: Electronic Circuits I Lab
COURSE CODE: EEE1302
Term: FALL 2022

Lab Report of Experiment No: 04


Experiment Name: Study of Clipping Circuits
Submitted To
Mirza Rashedduzaman (Ph.D)
Department of Electrical and Electronic Engineering
University of Liberal Arts Bangladesh (ULAB)

Submitted By:
Fahim Sadik
ID: 213014027
Section: 02

DATE OF SUBMISSION: 24/11/2022


Objectives
To study the diode applications in clipping circuits.

Apparatus Required
1. Function Generator
2. Oscilloscope
3. DC Power Supply
4. Breadboard
5. Diodes
6. Resistor.

Theory
Clippers are networks that employ diodes to “clip” away a portion of an input signal
without distorting the remaining part of the applied waveform. There are two general
categories of clippers: series and parallel. The series configuration is defined as one
where the diode is in series with the load, whereas the parallel variety
has the diode in a branch parallel to the load.

Procedure
1. First we connect all the components like shown in figure 1.
2. The source then the diodes (like shown) and then resistor and connect the
oscilloscope at the ends of the resistor.
3. Same procedure we follow through all the rest of the experiments.
4. For better understanding we measure the input sine voltage by oscilloscope and
then again measure then voltage across the resistor time by time.
5. For the variable voltage source in between (shown in 3 and 4) we set the
minimum voltage of the source of dc volt and increase to 4v .
6. From this time we start tonotice the oscilloscope the changing of the circuit
voltage.
Fig. 1: Positive series
clipping

Fig. 2: Negative shunt


clipping

Fig. 3: Biased series negative clipping

Fig. 4: Biased shunt positive clipping

Result
We can see that the diodes clipping the input base on the position.
But the most interesting thing is the biased series and shunt clipping. For this when we
put 4V in the dc circuit we did see that a amount of voltage pass through the diode. Like
in details for biased series negative clipping the actual voltage was reduced by the dc
and the diode .
And then for the biased shun positive clipping the voltage did pass about for some time
when the dc voltage was more than the rising input voltage then the diode acted as a
forward bais and let the voltage pass through the diode,
Discussion
By this experiment we can get that clipping is done for circuits to clip voltage to a cartain
voltage. For a sinosidal voltage we can get a output voltage as we want by reducing it or
for a higher voltage time we can get a minimum voltage by this method. We can control
the output of the voltage or limit the wave side if we need a positive cycle or a negative
cycle for the instrument.

Picture 1:The sine wave we inputed.

Picture 2:Biased series negative clipping

Picture 3: Biased shunt positive clipping

You might also like