43

SЕRIES

Low profile PCB relays

10 - 16 A

Medical and
dentistry

Alarm systems

Air conditioners

Burners,
boilers and
furnaces

Electric and
electronic toys
and games

Door and gate

openers

Electronic
circuit boards

Vending
machines
FINDER reserves the right to alter characteristics at any time without notice. FINDER assumes no liability for damage to persons or property, caused as a result of the incorrect use or application of its products.
 43 SERIES 43
Low profile PCB relays 10 - 16 A SERIES

1 Pole - Low profile (15.4 mm height) 43.41 43.41-0300 43.61-0300

Type 43.41
- 1 Pole, 10 A (3.2 mm pin pitch)
Type 43.41-0300
- 1 Pole NO, 10 A (5 mm pin pitch) A
Type 43.61-0300
- 1 Pole NO, 16 A (5 mm pin pitch)
PCB mount - direct or via PCB socket (43.41
version)
• Sensitive DC coil:
- 250 mW (10 A version)
- 400 mW (16 A version)
• Very high coil-contact isolation 10 mm, • 3.2 mm contact pin pitch • 5.0 mm contact pin pitch • 5.0 mm contact pin pitch
6 kV (1.2/50 µs) • 1 Pole CO, 10 A • 1 Pole NO, 10 A • 1 Pole NO, 16 A
• Cadmium Free contacts (preferred version) • PCB direct or via socket • PCB mount • PCB mount
• Flux proof: RT II standard, (RT III option)

For UL ratings see:

“General technical information” page V

For outline drawing see page 5 Copper side view Copper side view Copper side view
Contact specification
Contact configuration 1 CO (SPDT) 1 NO (SPST-NO) 1 NO (SPST-NO)
Rated current/Maximum peak current A 10/15 10/15 16/25
Rated voltage/
Maximum switching voltage V AC 250/400 250/400 250/400
Rated load AC1 VA 2500 2500 4000
Rated load AC15 (230 V AC) VA 500 500 750
Single phase motor rating (230 V AC) kW — — —
Breaking capacity DC1: 30/110/220 V A 10/0.3/0.12 10/0.3/0.12 16/0.3/0.12
Minimum switching load mW (V/mA) 300 (5/5) 300 (5/5) 300 (5/5)
Standard contact material AgNi AgNi AgNi
Coil specification
Nominal voltage (UN) V AC (50/60 Hz) — — —
V DC 3 - 6 - 9 - 12 - 18 - 24 - 36 - 48 3 - 6 - 9 - 12 - 18 - 24 - 36 - 48 12 - 24 - 48
Rated power AC/DC VA (50 Hz)/W —/0.25 —/0.25 —/0.4
Operating range AC — — —
DC (0.7…1.5)UN (0.7…1.5)UN (0.7…1.2)UN
Holding voltage AC/DC —/0.4 UN —/0.4 UN —/0.4 UN
Must drop-out voltage AC/DC —/0.05 UN —/0.05 UN —/0.05 UN
Technical data
Mechanical life AC/DC cycles —/10 · 106 —/10 · 106 —/10 · 106
Electrical life at rated load AC1 cycles 100 · 103 100 · 103 50 · 103
Operate/release time  ms 6/4 6/2 6/2
Insulation between coil
and contacts (1.2/50 µs) kV 6 (10 mm) 6 (10 mm) 6 (10 mm)
IX-2018, www.findernet.com

Dielectric strength
between open contacts V AC 1000 1000 1000
Ambient temperature range °C –40…+85 –40…+85 –40…+85
Environmental protection RT II RT II RT II
Approvals (according to type)

3
43 43 SERIES
SERIES Low profile PCB relays 10 - 16 A

Ordering information
Example: 43 series low-profile PCB relay, 1 CO (SPDT), 24 V DC coil.

A A B C D

4 3 . 4 1 . 7 . 0 2 4 . 2 0 0 . 0
Series A: Contact material D: Special versions
0 = AgNi 0 = Flux proof (RT II)
Type 2 = AgCdO 1 = Wash tight (RT III)
4 = PCB - 3.2 mm pinning 4 = AgSnO2
(CO/SPDT, 10 A) 5=A  gNi + Au C: Options
PCB - 5 mm pinning 0 = None
(NO/SPST-NO, 10 A) B: Contact circuit
6 = PCB - 5 mm pinning 0=C  O (SPDT) - (for 43.41 only)
(NO/SPST-NO, 16 A) 3=N  O (SPST)

No. of poles
1 = 1 pole

Coil version
7 = Sensitive DC (only for 43.41)
Selecting features and options: only combinations in the same row are possible.
9 = DC (only for 43.61)
Preferred selections for best availability are shown in bold.
Coil voltage
Type Coil version A B C D
See coil specifications
43.41 sensitive DC 0-2-4-5 0-3 0 0-1
43.61 DC 0-2-4 3 0 0

Technical data
Insulation according to EN 61810-1
Nominal voltage of supply system V AC 230/400
Rated insulation voltage V AC 250 400
Pollution degree 3 2
Insulation between coil and contact set
Type of insulation Reinforced (10 mm)
Overvoltage category III
Rated impulse voltage kV (1.2/50 µs) 6
Dielectric strength V AC 4000
Insulation between open contacts
Type of disconnection Micro-disconnection
Dielectric strength V AC/kV (1.2/50 µs) 1000/1.5
Insulation between coil terminals
Rated impulse voltage (surge) differential mode
(according to EN 61000-4-5) kV(1.2/50 µs) 2
Other data
Bounce time: NO/NC ms 3/6
Vibration resistance (5…55)Hz: NO/NC g 15/3
Shock resistance g 15
Power lost to the environment without contact current W 0.25 (43.41) 0.4 (43.61)
with rated currentW 1.3 (43.41) 2 (43.61)
Recommended distance between relays mounted on PCB  mm ≥ 5
IX-2018, www.findernet.com

4
 43 SERIES 43
Low profile PCB relays 10 - 16 A SERIES

Contact specification
F 43 - Electrical life (AC) v contact current H 43 - Maximum DC1 breaking capacity

43.61 current limit A

43.41 current limit

DC breaking current (A)

Resistive load - cosϕ = 1
Inductive load - cosϕ = 0.4
Cycles

limit for 43.41

DC voltage (V)

• When switching a resistive load (DC1) having voltage and current

values under the curve, an electrical life of ≥ 100 · 103 for 43.41 and
≥ 50 · 103 for 43.61 can be expected.
• In the case of DC13 loads, the connection of a diode in parallel with
the load will permit a similar electrical life as for a DC1 load.
Note: the release time for the load will be increased.

Coil specifications
DC coil data - 0.25 W sensitive (type 43.41) R 43 - DC coil operating range v ambient temperature
Nominal Coil Operating range Resistance Rated coil
voltage code consumption
UN Umin Umax R I at UN
V V V Ω mA
3 7.003 2.2 4.5 36 83.5
6 7.006 4.2 9 150 40
9 7.009 6.5 13.5 324 27.7
12 7.012 8.4 18 580 20.7
18 7.018 13 27 1300 13.8
24 7.024 16.8 36 2200 10.9
36 7.036 25.2 54 5200 6.9
48 7.048 33.6 72 9200 5.2
1 - Max. permitted coil voltage.
2 - Min. pick-up voltage with coil at ambient temperature.
DC coil data - 0.4 W standard (type 43.61)

Nominal Coil Operating range Resistance Rated coil

voltage code consumption
UN Umin Umax R I at UN
V V V Ω mA
12 9.012 8.4 14.4 360 33.3
24 9.024 16.8 28.8 1400 17.1
48 9.048 33.6 57.6 5760 8.3

Outline drawings
Type 43.41 Types 43.41-0300/43.61-0300
IX-2018, www.findernet.com

5
43 95 SERIES
SERIES Sockets and accessories for 43 series relays

PCB socket (for changeover contacts only) 95.23 (blue) 95.23.0 (black)
For relay type 43.41 43.41
Accessories
A 95.23 Metal retaining clip
Approvals (supplied with socket - packaging code SNA) 095.43
(according to type): Technical data
Rated values 10 A - 250 V
Insulation 6 kV (1.2/50 µs) between coil and contacts
Protection category IP 20
Ambient temperature °C –40…+70

43.41

Copper side view

Packaging codes
How to code and identify retaining clip and packaging options for sockets.

Example:

9 5 . 2 3 S N A

A Standard packaging

SN Metal retaining clip

IX-2018, www.findernet.com

9 5 . 2 3 Without retaining clip

6 Please see general technical information