CONCRETE MIXER MACHINE TSCM-260

OPERATING INFORMATION

To reduce the risk of injury, all operators and maintenance personnel must
read and understand these instructions before operating, changing
accessories, or performing maintenance . All possible situations cannot be
covered in these instructions. Care must be exercised by everyone using,
maintaining or working near this equipment.
Technical Specification:
Model TSCM-260
Engine Diesel engine 4.5~6.5 HP
Capacity 260 L
Drum rotation speed 25-30rpm
Productivity 6-20m3/h
Drum Diameter 28

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions,
operating, maintenance and cleaning procedures, parts list. Keep your
invoice with this manual. Write the invoice number on the inside of the
front over. Keep this manual and invoice in a safe and dry place for future
reference.
SAVE WARNING AND PRECAUTIONS
1. KEEP WORK AREA CLEAN. Cluttered work areas invite injuries.
2. KEEP CHILDREN AWAY FROM WORK AREA. Do not allow children to
the Drum with a shovel or other tools to break up accumulations of dried
concrete mix, as damage to the Concrete Mixer may result.
3. STOP FOR EQUIPMENT. When not in use and equipment should be
stored in a dry location to inhibit rust. Always lock up tools and equipment
and keep out of reach of children.
4. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS. Read warning labels on prescriptions to determine of your
judgment or reflexes are impaired while talking drugs. If there is any doubt,
do not attempt to use this tool.
32 Bolt (M12*35) 02
5. USE EYE, HEARING, AND DUST PROTECTION. Wear approved safety
impact eye glasses, approved hearing protection and approved dust 33 Deum Sealed Cup 01
protection when working with this product. 34 Seal Ring(80*4) 01
6. DRESS SAFELY. Non-skid footwear or safety shoes should be used when 35 Main Axis 01
working with this product. Do not wear loose clothing or jewelry as they 36 Drum Bearing 02
can become caught in moving parts. Wear a protective hair or covering to 37 Bow Assembly 01
prevent long hair from becoming caught in moving parts. 38 Nut(M36) 01
7. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS. 39 Nut(M10) 01
8. DO NOT OVERREACH. Keep proper footing and balance at all times to 40 Bolt (M10*25) 01
prevent tripping, falling, back injury, etcetera. 41 Nut(M12) 01
9. STAY ALERT. Watch what you are doing at all times. Use common sense. 42 Bolt (M12*35) 01
Do not use this tool when you are tired or distracted from the job at hand. 43 Drum Assembly 01
10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check 44 Bolt (M6*20) 02
that this tool will operate properly and perform it’s intend function. Check 45 Flat Gasket (6) 02
for damaged parts and any other conditions that may affect the operation 46 Spring Cushion (6) 02
of this tool. Replace or repair damaged or repair damaged or worn parts 47 Big Gear Cover 01
immediately. 48 Nut(M12) 01
11. REPLA CONCRETE PARTS AND ACCESSORIES. When servicing, use only 49 Spring Cushion (12) 01
identical replay concrete parts. Only use accessories intended for use with 50 Flat Gasket (12) 01
this product. 51 Brale Flap 01
12. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry for 52 Steering Gear 01
better and safer performance.
13. MAINTENANCE: for your safety, service and maintenance should be
performed regularly by a qualified technician.
14. USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain
applications for which this product was designed. Do not use a small tool or
attachment to do the work of a larger industrial tool or attachment. Do not
use this product for which it was not intended.
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS
1. CAUTION: Never perform any services or maintenance on the Concrete
Mixer while it is running. Before performing services or maintenance, turn
1 Base Frame 01 off the engine and disconnect the spark plug wire to prevent accidental
2 Bolt (M10*45) 04 Connect Wheel shaft starting.
3 Wheel shaft 01 2. Before each use, inspect the general condition of the Concrete Mixer,
4 Flat Gasket (10) 04 Check for loose screws, misalignment, binding of moving parts, loose or
5 Spring Cushion (10) 04 broken parts, and any other condition that may affect operation. If
6 Nut (M10) 04 abnormal noise or vibration occurs, turn off the Concrete Mixer
7 Bolt (M10*45) 04 immediately and have the problem corrected before further use. Do not
8 Engine Base 01 use damaged equipment.
9 Flat Gasket (10) 04 3. Retighten the V-belt after the first 24 hours of use. The V-belt should be
10 Spring Cushion (10) 04 able to be pressed in no more than 1/4.
11 Nut (M10) 04 4. Periodically, recheck all nuts. Bolts and screws for tightness.
12 Engine Base 01 5. Thoroughly clean the Concrete Mixer at the end of each day’s operation.
13 Flat Gasket (10) 04 The Drum Assembly may be scoured for approximately two minutes, using
14 Spring Cushion (10) 04 a gravel and water mixture. Then, discharge the gravel/water mixture and
15 Bolt (M10*30) 04 hose down the Drum Assembly inside and out.
16 Belt Pulley 01 6. Dried concrete mix should be scraped out of the Drum. Do not beat on
handle this product and to play near product.
17 Engine 01
7.Prior to using the concrete mixer, make sure you read and completely.
18 C# Flat Key 01
This instruction manual and the gas engine manufacture’s instruction
19 Bolt (M10*25) 01
manual.
20 Spring Cushion (10) 01
8.Use common sense when handling oil. Transport fuel only in approved
21 Flat Gasket(10) 01
safety containers. Do not refuel the Engine with running or while it is hot.
22 Big Pulley 01
Do not smoke when refueling the Engine. Wipe up any fuel spills on the
23 C# Flat Key 01
Engine. Do not operate the Concrete Mixer if there is evidence of a fuel leak.
24 Bolt (M6*20) 04
Do not operate the Concrete Mixer in or around other flammable or
25 Spring Cushion (6) 01
explosive liquids or diesel. Do not operate the Concrete Mixer in a poorly
26 Flat Gasket (6) 01
ventilated or enclosed area.
27 Engine Box 01
9.Keep all guards in place and in proper working condition.
28 Alex Bed 01 10.Never stick your hands and/or tools into the drum assembly with the
29 Oil Cup 01 concrete mixer are operation.
30 Flat Gasket(12) 02 11.Avoid contact with a hot engine and its exhaust system. Allow the
31 Spring Cushion(12) 02 engine to cool before performing any services or maintenance.
12.Keep a safe clearance around the concrete mixer. Keep all people
(except the operator) a minimum of six feet from the Mixer during
operation.
13.Do not overload the concrete mixer. An overload may damage the
equipment.
14. Daily check the oil level in the Engine. Refer to the Engine manufacture’s
manual/for the type and level of oil recommended, and all other Engine
service and maintenance instructions.
15. Periodically, inspect the speed converter assembly and the wheel
bearings. For proper lubrication.
UNPACKING
When unpacking, check to make sure all parts listed in the Parts Lists are
included. Pls turn to place of purchase as soon as possible.
OPERATING INSTRUCTIONS
Note:All parts below refer to the parts list shown on page 8 and 9 of
this manual
1. Caution: Do not attempt to move the Concrete Mixer when it is full
and/or in operation.
2. Place the Concrete Mixer on a solid, flat, and level surface that is capable
of supporting the weight of the mixer and its load.
3. Start the Engine and allow it to reach the appropriate operating
temperature as instructed in the Engine manufacturer’s operating manual.
4. NOTE: Filling and emptying the Drum is best done with drum rotating. Do
not turn off the Concrete Mixer while full of cement.
5. With the Drum operating between 20-30RPM, the Concrete Mixer is now
ready for the addition of the concrete mix.
6. To determine the proper amount of water, gravel, cement, and sand,
refers to Figure A
SAMPLE MIX VOLUME
MIX VOLUME (CU.FT.) 3 Item Description Qty. Remark
 Item Description Qty. Remark Cement(Bags) 1
1 Bolt (M10*45) 01 Water(Gal.) 2-1/2
2 Spring Cushion (10) 01 Sand(GAL./Shovels) 9
3 Flat Gasket (10) 01 Gravel(GAL./Shovels) 12
4 Bevel Gear 01 Mix volume may vary depending on aggregate used.
5 Spring Cushion (10) 04 7. For best results, proceed as follows:
6 A# Flat Key(8*7*28) 01 A. Pour the required amount of water into the Drum
7 Bearing 02 6206 B. Add the required amount of gravel into the Drum
8 Bow 01 C. Add the required amount of cement into the Drum
9 Shaft 01 D. Add the required amount of sand into the Drum
10 Snap Ring 01 8.Allow adequate time for the water, gravel, cement and sand to
thoroughly mix.
9.After discharging the cement,turn the Hand Wheel clockwise to return
the Drum to its original position.Then,make sure to fully engage the Brake
Handle.
10.When finished,make sure to the roughly clean the inside of the Drum.

MAINTENANCE AND CLEANING

1. CAUTION: Never perform any services or maintenance on the Cement
Mixer while it is running. Before performing services or maintenance, turn
off the engine and disconnect the spark plug wire to prevent accidental
starting.
2. Before each use, inspect the general condition of the Cement Mixer,
Check for loose csrews, misalignment, binding of moving parts,loose or
brokrn parts, and any other condition that may affect operation. If
abnormal noise or vibration occurs, turn off the Cement Mixer immediately
and have the problem corrected before further use. Do not use damaged
DRUM EXPLODED DRAWING equipment.

3. Retighten the V-belt after the first 24 hours of use. The V-belt should be
able to be pressed in no more than 1/4.
4. Periodically, recheck all nuts. Bolts and screws for tightness. Item Description Qty. Remark
5. Thoroughly clean the Cement Mixer at the end of each day’s operation. 1 Bearing 02 30210
The Drum Assembly may be scoured for approximately two minutes, using 2 Drum 01
a gravel and water mixture. Then,discharge the gravel/water mixture and 3 Nut 06 M8
hose down the Drum Assembly inside and out.
4 Flat Gasket (10) 06 8
6. Dried cement mix should be scrped out of the Drum. Do not beat on the
5 Spring Cushion (10) 06 8
Drum with a shovel or other tools to break up accumulations of dried
6 Bolt (M8*35) 06
cement mix, as demage to the Cement Mixer may result.
7 Big Gear Ring 01
7. Do not pour or spray water over the Engine.(See Assy. Diagram)
8 Flat Gasket (10) 06
8. Daily check the oil level in the Engine. Refer to the Engine manufacture’s
9 Spring Cushion (10) 06
manual/for the type and level of oil recommended, and all other Engine
10 Fix Seat 03
service and maitenance instructions.
11 Bolt (M10*35) 06
9.Check the oil which is in the Drum Bearing and bevel gear frequently,
filling with grease oil regularly.Otherwise,the bearing are easy to broken.
10. Periodically, inspect the Speed Converter Assembly and the Wheel
Bearings. For proper lubrication. (See Assy. Diagram)
WARRANTY
These products are covered by warranty for a period of six (6) months from
the date of purchase against defects in material or workmanship provided
that:
·The product concerned has been operated and maintained accordance
with the operating instructions.
·Has not been tampered with or repaired by any unauthorized person.
·Has not been tampered with or repaired by any unauthorized person.
The owner is responsible for the cost of transportation to and from the
authorized repairer and the unit is at the owners risk while in transit to and
from the repairer.
Impact damage is not covered under warranty. Clutches are not covered
under any warranty. Engines are warranted by their manufacturer.
BOW EXPLODED DRAWING