ORDER NO.

RRV4296
VSX-522-K

AV Receiver

VSX-522-K
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Remarks

VSX-522-K CUXESM AC 120 V

K-MZV FEB. 2012 Printed in Japan

 1 2 3 4

SAFETY INFORMATION

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-
yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.

WARNING
B This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
harm.
Health & Safety Code Section 25249.6 - Proposition 65

(FOR USA MODEL ONLY)

ANY MEASUREMENTS NOT WITHIN THE LIMITS
1. SAFETY PRECAUTIONS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
The following check should be performed for the
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
continued protection of the customer and service
RETURNING THE APPLIANCE TO THE CUSTOMER.
technician.
C LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground 2. PRODUCT SAFETY NOTICE
(water pipe, conduit, etc.) by connecting a leakage Many electrical and mechanical parts in the appliance
current tester such as Simpson Model 229-2 or have special safety related characteristics. These are
equivalent between the earth ground and all exposed often not evident from visual inspection nor the protection
metal parts of the appliance (input/output terminals, afforded by them necessarily can be obtained by using
screwheads, metal overlays, control shaft, etc.). Plug replacement components rated for voltage, wattage, etc.
the AC line cord of the appliance directly into a 120 V Replacement parts which have these special safety
AC 60 Hz outlet and turn the AC power switch on. Any characteristics are identified in this Service Manual.
current measured must not exceed 0.5 mA. Electrical components having such features are
identified by marking with a > on the schematics and on
D
the parts list in this Service Manual.
Reading should The use of a substitute replacement component which
Leakage not be above does not have the same safety characteristics as the
Device current 0.5 mA
under tester PIONEER recommended replacement one, shown in the
test parts list in this Service Manual, may create shock, fire,
Test all or other hazards.
exposed metal
surfaces Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Also test with Manual. A subscription to, or additional copies of,
plug reversed Earth PIONEER Service Manual may be obtained at a nominal
E (Using AC adapter ground
plug as required) charge from PIONEER.

AC Leakage Test

2 VSX-522-K
1 2 3 4
 5 6 7 8

CONTENTS
SAFETY INFORMATION.......................................................................................................................................................... 2
1. SERVICE PRECAUTIONS .................................................................................................................................................... 4
1.1 NOTES ON SOLDERING ............................................................................................................................................... 4 A
1.2 NOTES ON REPLACING PARTS ................................................................................................................................... 4
1.3 SERVICE NOTICE.......................................................................................................................................................... 4
2. SPECIFICATIONS................................................................................................................................................................. 5
3. BASIC ITEMS FOR SERVICE .............................................................................................................................................. 6
3.1 CHECK POINTS AFTER SERVICING ........................................................................................................................... 6
3.2 JIGS LIST ....................................................................................................................................................................... 6
3.3 PCB LOCATIONS ........................................................................................................................................................... 7
4. BLOCK DIAGRAM ................................................................................................................................................................ 8
4.1 OVERALL WIRING DIAGRAM ....................................................................................................................................... 8
4.2 AUDIO BLOCK DIAGRAM............................................................................................................................................ 10
4.3 D-MAIN BLOCK DIAGRAM .......................................................................................................................................... 12
4.4 POWER SUPPLY BLOCK DIAGRAM........................................................................................................................... 14 B
4.5 VIDEO BLOCK DIAGRAM............................................................................................................................................ 16
5. DIAGNOSIS ........................................................................................................................................................................ 17
5.1 TROUBLESHOOTING.................................................................................................................................................. 17
5.2 USB/iPod ERROR MESSAGE...................................................................................................................................... 29
5.3 DETECTION CIRCUIT ................................................................................................................................................. 30
5.4 IC INFORMATION ........................................................................................................................................................ 32
6. SERVICE MODE ................................................................................................................................................................. 38
6.1 SERVICE MODE .......................................................................................................................................................... 38
7. DISASSEMBLY ................................................................................................................................................................... 42
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................ 50
8.1 ADJUSTMENT REQUIRED WHEN THE UNIT IS REPAIRED OR REPLACED .......................................................... 50
C
8.2 UPDATING OF THE FIRMWARE ................................................................................................................................. 51
8.3 IDLE CURRENT ADJUSTMENT .................................................................................................................................. 57
9. EXPLODED VIEWS AND PARTS LIST............................................................................................................................... 58
9.1 PACKING SECTION ..................................................................................................................................................... 58
9.2 EXTERIOR SECTION .................................................................................................................................................. 60
10. SCHEMATIC DIAGRAM .................................................................................................................................................... 64
10.1 AUDIO ASSY .............................................................................................................................................................. 64
10.2 AMP5 ASSY (1/2) ....................................................................................................................................................... 66
10.3 AMP5 ASSY (2/2) ....................................................................................................................................................... 68
10.4 MAIN ASSY ................................................................................................................................................................ 70
10.5 D-MAIN ASSY (1/4) .................................................................................................................................................... 72
10.6 D-MAIN ASSY (2/4) .................................................................................................................................................... 74 D
10.7 D-MAIN ASSY (3/4) .................................................................................................................................................... 76
10.8 D-MAIN ASSY (4/4) .................................................................................................................................................... 78
10.9 VIDEO, G-L, G-R, WG-B and WG-A ASSYS.............................................................................................................. 80
10.10 BRG-A, BRG-B and BRG-C ASSYS ........................................................................................................................ 82
10.11 FRONT, INSEL, HP, MIC, F-USB and WG ASSYS................................................................................................... 84
10.12 STANDBY ASSY....................................................................................................................................................... 86
11. PCB CONNECTION DIAGRAM ........................................................................................................................................ 88
11.1 AUDIO ASSY .............................................................................................................................................................. 88
11.2 AMP5 ASSY ............................................................................................................................................................... 90
11.3 MAIN ASSY ................................................................................................................................................................ 92
11.4 D-MAIN ASSY ............................................................................................................................................................ 96
11.5 VIDEO ASSY ............................................................................................................................................................ 100 E
11.6 G-L, G-R, WG-B and WG-A ASSYS......................................................................................................................... 101
11.7 BRG-A, BRG-B and BRG-C ASSYS ........................................................................................................................ 102
11.8 FRONT, INSEL, HP, MIC, F-USB and WG ASSYS................................................................................................... 106
11.9 STANDBY ASSY....................................................................................................................................................... 110
12. PCB PARTS LIST ............................................................................................................................................................ 111

VSX-522-K 3
5 6 7 8
 1 2 3 4

1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
A • For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.

• Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 ºC.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 ºC in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Do NOT use a soldering iron whose tip temperature cannot be controlled.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
B
temperatures (hard to melt/easy to harden).

The following lead-free solders are available as service parts:

• Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

1.2 NOTES ON REPLACING PARTS

The part listed below is difficult to replace as a discrete component part.
When the part listed in the table is defective, replace whole Assy.
Parts that is Difficult to Replace
Assy Name
Ref No. Function Part No. Remarks
IC2000 HDMI Receiver —————— IC with heat-pad
D IC2007 D-MAIN 3.3 V Power Supply IC —————— IC with heat-pad
IC2008 D-MAIN 5 V Power Supply IC —————— IC with heat-pad
D-MAIN Assy IC2013 DSP 1.2 V Power Supply IC —————— IC with heat-pad
IC2015 DSP 1.8 V Power Supply IC —————— IC with heat-pad
IC2016 DSP IC —————— IC with heat-pad
IC2024 USB 5 V SW IC —————— IC with heat-pad

1.3 SERVICE NOTICE

• Discharging
For more detail, please refer to "7. DISASSEMBLY - 1. Discharging".

• Notes on Ground Points Connection

For more detail, please refer to "7. DISASSEMBLY - 2. Notes on Ground Points Connection".
F

4 VSX-522-K
1 2 3 4
 5 6 7 8

2. SPECIFICATIONS

Amplifier section Accessories A

Continuous average power output of 80 watts* per
channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no
more than 0.08 %** total harmonic distortion.
Front (stereo) ............................................................... 80 W + 80 W
Power output (1 kHz, 6 Ω, 1 %) ........................... 140 W per channel
Guaranteed speaker impedance .................................... 6 Ω to 16 Ω
* Measured pursuant to the Federal Trade Commission’s Trade
Regulation rule on Power Output Claims for Amplifiers
** Measured by Audio Spectrum Analyzer
Microphone (for Auto MCACC setup)
Audio Section (APM7010)
Input (Sensitivity/Impedance)
LINE......................................................................... 200 mV/47 kΩ B
Signal-to-Noise Ratio (IHF, short circuited, A network)
LINE.......................................................................................98 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
LINE.......................................................................................79 dB

Video Section
Signal level
Composite ................................................................ 1 Vp-p (75 Ω)

Tuner Section
Frequency Range (FM) ................................. 87.5 MHz to 108 MHz
Antenna Input (FM)................................................75 Ω unbalanced
Frequency Range (AM) ...................................530 kHz to 1700 kHz Remote control (AXD7660) Dry cell batteries
C
Antenna (AM) ............................................................. Loop antenna (8300766000010-IL) (AAA size IEC R03) x2

Digital In/Out Section

HDMI terminal ...........................................................Type A (19-pin)
HDMI output type............................................................5 V, 100 mA
USB (iPod) terminal.............................. USB2.0 Full Speed (Type A)

Miscellaneous
AM loop antenna FM wire antenna
Power Requirements ............................................... AC 120 V, 60 Hz
(E601019000010-IL) (E605010140010-IL)
Power Consumption ................................................................415 W
In standby...........................................................0.4 W (ARC OFF)
Dimensions....................435 mm (W) x 168 mm (H) x 342.5 mm (D)
17 3/16 in. (W) x 6 5/8 in. (H) x 13 1/2 in. (D) Warranty card
Weight (without package) ..................................... 8.7 kg (19 lb 3 oz) D
Quick start guide (5707000006490-IL)
Safety Brochure
Note Operating instructions (CD-ROM)(6517000000500-IL)
• Specifications and the design are subject to possible
modifications without notice, due to improvements.

VSX-522-K 5
5 6 7 8
 1 2 3 4

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
A
Items to be checked after servicing
To keep the product quality after servicing, confirm recommended check points shown below.
No. Procedures Check points
1 Confirm whether the customer complain has been solved. The customer complain must not be reappeared.
If the customer complain occurs with the particular source, such Video, Audio and operations must be normal.
as Dolby Digital, DTS, AAC, DVD-A and HDMI, input it for the
operation check.

2 Check the analog audio playback. Each channel audio and operations must be normal.
(Make the analog connections with a DVD player.)
3 Check the digital audio playback. Each channel audio and operations must be normal.
(Make the digital connections with a DVD player.)
B
4 Check surround playback. Each channel audio and operations must be normal.
(Select Surround mode and check the multichannel operations
via the DSP circuit.)

5 Check the video outputs. Video and operations must be normal.

(Connect with a DVD player.)
6 Check the tuner (AM and FM) operations. Audio and operations must be normal.
7 Check the sound from headphone output. Sound must be normal, without noise.
8 Check the appearance of the product. No scratches or dirt on its appearance after receiving it for
service.

C
See the table below for the items to be checked regarding video and audio.
Item to be checked regarding video Item to be checked regarding audio
Block noise Distortion
Horizontal noise Noise
Flicker Volume too low
Disturbed image (video jumpiness) Volume too high
Too dark Volume fluctuating
Too bright Sound interrupted
Mottled color
D

3.2 JIGS LIST

Jigs List
Jig Name Part No. Remarks
RS-232C update jig (Jig + 10P FFC) GGF1642 MAIN microcomputer firmware update
RS-232C cable (9-pin to 9-pin, straight cable) (Marketing product) (RS-232C ↔ Rear panel)
RS-232C update jig GGF1646 HDMI (SUB) & CEC microcomputer firmware update
E USB cable (USB A-Type ↔ USB B-Type) (Marketing product) (USB ↔ Rear panel)
9P extension jig cable GGD1739 Diagnosis (AMP5 Assy ↔ AUDIO Assy)
Board to board extension jig cable GGD1756 Diagnosis (D-MAIN Assy ↔ BRG-A Assy)
Board to board extension jig cable GGD1798 Diagnosis (D-MAIN Assy ↔ BRG-C Assy)
Board to board extension jig cable GGD1799 Diagnosis (D-MAIN Assy ↔ BRG-C Assy)

Lubricants and Glues List

Name Part No. Remarks

F
Silicon grease GEM1057 Refer to "9.2 EXTERIOR SECTION".
GYA1011
Silicon adhesive Refer to "9.2 EXTERIOR SECTION".
(KE40RTV-W)
6 VSX-522-K
1 2 3 4
 5 6 7 8

3.3 PCB LOCATIONS

A
A AUDIO ASSY

VIDEO ASSY E

STBY ASSY S D D-MAIN ASSY

MAIN ASSY C L BRG-C ASSY

WG-B ASSY H J BRG-A ASSY

K BRG-B ASSY

AMP5 ASSY B
I WG-A ASSY C
G-L ASSY F G G-R ASSY

Q F-USB ASSY

HP ASSY O P MIC ASSY

INSEL ASSY N R WG ASSY

FRONT ASSY M

NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES
NSP 1..PCB TTL ASSY MAIN 7025HK1106010-IL NSP 1..PCB TTL ASSY AUDIO 7025HK1106013-IL
2..MAIN ASSY 7028071611060-IL 2..AUDIO ASSY 7028071641060-IL E
2..G-R ASSY 7028071614060-IL
2..G-L ASSY 7028071615060-IL NSP 1..PCB TTL ASSY DMAIN 7025HK1106014-IL
2..WG-A ASSY 7028071616060-IL 2..D-MAIN ASSY 7028071651010-IL

2..WG-B ASSY 7028071617060-IL NSP 1..PCB TTL ASSY AMP5 7025HK1106015-IL

2..AMP5 ASSY 7028070243010-IL
NSP 1..PCB TTL ASSY VIDEO 7025HK1106012-IL
2..VIDEO ASSY 7028071631010-IL NSP 1.PCB TTL ASSY FRONT 7025HK1106011-IL
2..STBY ASSY 7028071632010-IL 2..FRONT ASSY 7028071621060-IL
2..BRG-A ASSY 7028071633010-IL 2..HP ASSY 7028071622060-IL
2..BRG-B ASSY 7028071634010-IL 2..INSEL ASSY 7028071623060-IL
2..MIC ASSY 7028071624060-IL
2..BRG-C ASSY 7028071635010-IL
F
2..F-USB ASSY 7028071625060-IL
2..WG ASSY 7028071627060-IL

VSX-522-K 7
5 6 7 8
 1 2 3 4

4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A - When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
- The > mark found on some component parts indicates the importance of the safety factor of the part. WG ASSY
Therefore, when replacing, be sure to use parts of identical designation. R (7028071627060-IL)

FROM MAIN TRANS

CP1 CP2 CP3

B 1 AC 1 AC 1 AC
2 GND 2 AC 2 AGND
3 AC 3 AC 3 AC

CP403 CN3
+HIGHB 1 1 +HIGHB
+HIGHB 2 2 +HIGHB
+HIGHB 3 3 +HIGHB
-HIGHB 4 4 -HIGHB

P O
-HIGHB 5 5 -HIGHB
-HIGHB 6 6 -HIGHB
HIGHGND 7 7 HIGHGND

B B 1/2- B 2/2
HIGHGND 8 8 HIGHGND
MIC ASSY HP ASSY HIGHGND 9
PREGND10
9 HIGHGND
10 PREGND
(7028071624060-IL) (7028071622060-IL) CP402 CN1
AMP5 ASSY FL
FR
1
2
1 FL
2 FR

(7028070243010-IL)
C 3 3C
SL 4 4 SL
SR 5 5 SR
1 +9.1V 1 FL 6 AGND CN404
2 GNDA 1 HP_DET 2 AGND 7 SR DC_DET4 1
C 3 -9.1V 2 HP_RO 3 SL 8 AGND DC_DET3 2
4 MIC 3 GNDA 4 AGND 9 FR ASO_DET 3
5 MIC_DET 4 HP_LO 5C 10 AGND RADI_THERMAL 4
CN901 CN721 CP401 TR_THERMAL 5
CN5
DGND1 1

C
DGND1 2
+12V 3
CP901 CP721
+12V 4
1 MIC DET 1 HP LO
2 MIC
3 NC
4 -9.1V
K 2 GNDHP
3 HP RO
4 HP DET
MAIN ASSY
5 GNDA
6 +9.1V BRG-B ASSY CP204
(7028071611060-IL)
HP_DET 1
(7028071634010-IL) MIC_DET 2
VOL_DATA 3
VOL_CLK 4
SW_SUM 5
HP_RLY 6
A MUTE 7
CN400 SB MUTE 8
CP402 CN402 1 FL 6 GNDA NC 9
D HP LO 1 1 HP_LO 2 GNDA 7 SR
GNDA 2 2 GNDA 3 SL 8 GNDA

A
HP RO 3 3 HP_RO 4 GNDA 9 FR
Z2 MUTE 4 4 Z2_MUTE 5C 10 GNDA
SB MUTE 5 5 SB_MUTE
AMUTE 6 6 A_MUTE CP13
HPRLY 7 7 HP_RLY
SW SUM 8
Z2VOL DATA 9
8 SW_SUM
9 Z2VOL_DATA
AUDIO ASSY CN401
MUTE_B+ 1
+12V 2
CP17
1 MUTE_B+
2 A+12V
U/DGND 1
TUNER_INT 2
TUNER_SDIO 3
Z2VOL CLK 10
VOL DATA 11
VOL CLK 12
10 Z2VOL_CLK
11 VOL_DATA
12 VOL_CLK
(7028071641060-IL) +12V 3
GNDA 4
3 A+12V
4 AGND
TUNER_SCLK 4
TUNER_SEN 5
TUNER_RST 6
+12V 13 13 +12V GNDA 5 5 AGND
-12V 6 6 A-12V 2533_CTL 7
GNDA 14 14 GNDA 1 SBLIN 11 SRIN
MIC 15 15 MIC 2 GNDA 12 GNDA -12V 7 7 A-12V
GNDA 16 16 GNDA 3 SBRIN 13 FLIN GNDA 8 8 AGND CP16
-12V 17 17 -12V 4 GNDA 14 GNDA BT_R 9 9 BT_R
OSD_RST 1
5 SWIN 15 FRIN GNDA 10 10 AGND
OSD_CE 2
6 GNDA 16 GNDA BT_L 11 11 BT_L
OSD_CLK 3
7 CIN 17 AIN_L GNDA 12 12 AGND
OSD_DATA 4

CN403
8 GNDA
9 SLIN
10 GNDA
18 GNDA
19 AIN_R
TUNER_R13
GNDA 14
TUNER_L15 E 13 TU_R
14 AGND
15 TU_L
CTL_A 5
CTL_B 6
U/DGND 7
+5V 8
E VIDEO ASSY VIDEO_MUTE 9

(7028071631010-IL)
CP15
CP403 U/DGND 1
G-L ASSY CN9 CP9

F (7028071615060-IL)
1 SBL_OUT
2 GNDA
3 SBR_OUT
4 GNDA
11 SR_OUT
12 GNDA
13 FL_OUT
14 GNDA
OSD_RST 1
OSD_CE 2
OSD_CLK 3
1 OSD_RST
2 OSD_CE
3 OSD_CLK
MUTE_B+ 2
U/DGND 3
FBRL 4
SBRL 5
5 SW_OUT 15 FR_OUT OSD_DATA 4 4 OSD_DATA SURL 6
6 GNDA 16 GNDA CTL_A 5 5 CTL_A CRL 7
7 C_OUT 17 AIN_L CTL_B 6 6 CTL_B FRL 8
G-R ASSY U/DGND 7 7 U/DGND

G 8 GNDA 18 GNDA DC_PRO 9

9 SL_OUT 19 AIN_R +5V 8 8 +5V -VF(-30V) 10
(7028071614060-IL) 10 GNDA VIDEO_MUTE 9 9 VIDEO_MUTE U/DGND 11

H WG-B ASSY
(7028071617060-IL) J
F BRG-A ASSY
WG-A ASSY (7028071633010-IL)
I (7028071616060-IL)

8 VSX-522-K
1 2 3 4
 5 6 7 8

A
ASSY
FRONT ASSY
CN702
STBY_KEY 4
CP702
1 STBY_KEY N
8071627060-IL) M (7028071621060-IL)
INPUT_UP 3
GNDU 2
INPUT_DOWN 1
2 INPUT_UP
3 GNDU
4 INPUT_DOWN INSEL ASSY
1 -30V 13 FLR_DATA
(7028071623060-IL)
2 -30V 14 FLT_CLK
3 CPU_ST_VCC 15 FLT_CE
4 CPU_ST_VCC 16 INPUT_UP
1 HDMI+12V 5 GNDU 17 KEY2
2 STBY RLY 6 GNDU 18 KEY3
3 PDN
4 CPU ST VCC
5 CPU_+3.3V
6 GNDU
7 CPU_+3.3V
8 CPU_+3.3V
9 ST_H+5V
10 POWERDOWN
19 KEY1 (STBY_KEY)
20 INPUT_DN
21 VOL_UP
22 VOL_DN
1 GNDUSB
2 D+
Q
7 FL2
8 FLCT
11 RMC 23 THRU_LED 3 D-
4 GNDUSB
F-USB ASSY
12 STBY_RLY
AIN TRANS
9 FL1 5 USB+5V (7028071625060-IL)
CN701 CN704AA CN2006

P2 CP3
AC 1 AC B
2 AC 2 AGND
CP301
3 AC 3 AC CP701 CN704B CP2006
LIVE 1
AC CORD 1 FLAC 1 UCHGND
NEUTRAL 2 2 FLCT 1 THRU LED 13 RMC 2 D+
3 FLAC 2 VOL DN 14 POWER DN 3 D-
CP303 3 VOL UP 15 H+5V
1 4 CPU GND 4 USBGND
5 CPU+3.3V 4 IN DN 16 CPU+3.3V 5 USB+5V
VOL SEL 2 5 KEY1 17 CPU+3.3V
3 6 STBY VCC
7 PDN 6 KEY3 18 ST VCC
CP302 8 STBY RLY 7 KEY2 19 ST VCC
1 9 CPU_ST_VCC 8 IN UP 20 GNDU
TRANS 9 FLT CE 21 GNDU
2 10 FLT CLK 22 FL-30V
CP304 11 FLT DATA 23 FL-30V
FLAC 1 12 STBY RLY
TRANS FLCT 2 STBY B'D
FLAC 3

S STBY ASSY
(7028071632010-IL) CP2005
1 DC DET4
2 DC DET3 C
3 ASO_DET
4 RADI_DET
5 TRTHER_DET
CN5 CP2004
DGND1 1 1 D+12V
DGND1 2 2 D+12V
+12V 3 3 DGND
+12V 4
L BRG-C ASSY 4 DGND

SY (7028071635010-IL)
611060-IL) CN204
CP2001
HP DET 1
CN2001
1 HP DET
1 HP DET

D D 1/4- D 4/4
2 MIC DET MIC DET 2 2 MIC DET
3 VOL DATA VOL DATA 3 3 VOL DATA
4 VOL CLK VOL CLK 4 4 VOL CLK
5 SW SUM SB MUTE 5 5 SB MUTE
A MUTE 6 6 A MUTE
6 HP RLY
7 A MUTE
8 SB MUTE
SW SUM 7
HP RLY 8
7 SW SUM
8 HP RLY
D-MAIN ASSY
9 NC GNDU 9
FL-30V 10
DC DET 11
9 GNDU
10 FL-30V
11 DC DET
(7028071651010-IL) D
F RLY 12 12 F RLY
C RLY 13 13 C RLY
S RLY 14 14 S RLY
CP13 CN13 MUTE B+ 15 15 MUTE B+
U/DGND 1 1 GNDU GNDU 16 16 GNDU
TUNER_INT 2 2 TUNER INT TUNER SCLK17 17 TUNER SCLK
TUNER_SDIO 3 3 TUNER SDIO TUNER SDIO18 18 TUNER SDIO
TUNER_SCLK 4 4 TUNER SCLK TUNER SEN19 19 TUNER SEN
TUNER_SEN 5 5 TUNER SEN TUNER RST20 20 TUNER RST
TUNER_RST 6 6 TUNER RST TUNER INT21 21 TUNER INT
2533_CTL 7 7 NC V CTL B 22 22 BH76330 B
V CTL A 23 23 BH76330 A
OSD DATA 24 24 OSD DATA
CP16 CN16 OSD CLK 25 25 OSD CLK
OSD_RST 1 1 OSD RST OSD CE 26 26 OSD CE
OSD_CE 2 2 OSD CE OSD RST 27 27 OSD RST
OSD_CLK 3 3 OSD CLK
OSD_DATA 4 4 OSD DATA CP2002 CN2002
CTL_A 5 5 V CTL A V+5V 1 1 V+5V
CTL_B 6 6 V CTL B CPU+3.3V 2 2 CPU+3.3V
U/DGND 7 7 GNDU VIDEO MUTE 3 3 VIDEO MUTE
+5V 8 8 V+5V(A+5V) SCLK JTAG 4 4 SCLK JTAG
VIDEO_MUTE 9 9 VIDEO MUTE BUSY JTAG 5 5 BUSY JTAG E
CE 6 6 CE
EPM UP 7 7 EPM UP
CNVSS UP 8 8 CNVSS UP
CP15 CN11
232 TX/U RX 9 9 232TX/U RX
U/DGND 1 1 GNDU 232 RX/U TX 10 10 232RX/U TX 1 AINR 11 SL
MUTE_B+ 2 2 MUTE B+ RESET 11 11 RESET 2 AGND 12 AGND
U/DGND 3 3 GNDU CEC RXD 12 12 CEC RXD 3 AINL 13 C
FBRL 4 4 NC CEC TXD 13 13 CEC TXD 4 AGND 14 AGND
SBRL 5 5 NC CEC OPO 14 14 CEC OPO 5 FR 15 SW
SURL 6 6 S RLY SUB RXD 15 15 SUB RXD 6 AGND 16 AGND
CRL 7 7 C RLY SUB TXD 16 16 SUB TXD 7 FL 17 SBR
FRL 8 8 F RLY GNDD 17 17 GNDD 8 AGND 18 AGND
DC_PRO 9 9 DC DET SUB OPO 18 18 SUB OPO 9 SR 19 SBL
-VF(-30V) 10 10 FL-30V H+5V 19 19 H+5V 10 AGND
U/DGND 11 11 GNDU CN2003

CP2003
1 AIN R 11 SL OUT
2 GNDA 12 GNDA
3 AIN L 13 C OUT
4 GNDA 14 GNDA F
5 FR OUT 15 SW OUT
6 GNDA 16 GNDA
7 FL OUT 17 SBR OUT
8 GNDA 18 GNDA
9 SR OUT 19 SBL OUT
10 GNDA

VSX-522-K 9
5 6 7 8
 1 2 3 4

4.2 AUDIO BLOCK DIAGRAM

M FRONT ASSY
A

A AUDIO ASSY

P
MIC ASSY

10 VSX-522-K
1 2 3 4
 5 6 7 8

O HP ASSY

B AMP5 ASSY C MAIN ASSY

P Q F-USB ASSY
IC ASSY

VSX-522-K 11
5 6 7 8
 1 2 3 4

4.3 D-MAIN BLOCK DIAGRAM

Q2035

12 VSX-522-K
1 2 3 4
 5 6 7 8

D D-MAIN ASSY
A

C
4

6
3

Q2034
FDC608PZ
Q2035

VSX-522-K 13
5 6 7 8
 1 2 3 4

4.4 POWER SUPPLY BLOCK DIAGRAM

MAIN TRANS
S1(AMP B+/B-)

S2(+12V,-12V)

AC CORD

C S3(522:DSP, HDMI)
(922L/822:USB)

S4(FLT)

SUB TRANS

F
S STBY ASSY

14 VSX-522-K
1 2 3 4
5 6 7 8

6
3

1
Q2026
FDC608PZ
Q2027
C

6
3

1
Q2028
FDC608PZ
Q2029

1
Q2034
FDC608PZ
Q2035
4

D
3

Q2030
FDC608PZ
Q2031

4
GND FAULT
5

6
1

IN OUT
2

IN OUT
3

EN LIM
4

IC2025
TPS2557
3

Q2032
FDC608PZ
Q2033

VSX-522-K 15
5 6 7 8
 1 2 3 4

4.5 VIDEO BLOCK DIAGRAM

E VIDEO ASSY

BD
SAT

75

C 75

16 VSX-522-K
1 2 3 4
 5 6 7 8

5. DIAGNOSIS
5.1 TROUBLESHOOTING
A
[1] DSP TROUBLESHOOTING

TROUBLESHOOTING FOR ALL DESTINATION

Step 0: Preliminary confirmation
CN2002, CN2001, CN2003, CP2004 B to B connector, wire

Are the connectors No Insert the connectors

securely inserted? completely.

Yes

To Step 1 B

Step 1: Fixed board

Confirm the following items before checking

Do screws of back chassis No

Tighten screws securely.
securely tighten?

Yes

To Step 2 C

Step 2: Power supply

IC2007 (pin 2)
12 V input

No Check the IC2007 and its OK Replace IC2007 or

Is the voltage 12 V? check the MAIN Assy.
peripheral circuits.

Yes
L2007 D

No No Check the peripheral circuits or the OK

Is the voltage 3.3 V output? Is pin 7 (en) of IC2007 high? Replace IC2007.
MAIN microcomputer (IC2023).

Yes
Yes

IC2013 (pin 2) (to chassis) IC2005 (pin 5) (to chassis)

Check the IC2016 DSP Check the IC2000 HDMI

No power pin (cvdd and dvdd) No power pin (avdd33 and E
Is the voltage of 1.2 V output? and its peripheral circuits Is the voltage of 1.8 V output? advdd18) and its peripheral
or must be replaced circuits or must be replaced
IC2016, IC2013. IC2000, IC2005.
Yes Yes

Check the IC2016 DSP power pin (cvdd and Check the IC2000 HDMI power pin
dvdd): cvdd: 1.2 V, dvdd: 3.3 V. (acvdd33 and advdd18): 3.3 V, 1.8 V.
OK OK
+3.3V line of D-MAIN Assy is OK. +3.3V line of D-MAIN Assy is OK.

VSX-522-K 17
5 6 7 8
 1 2 3 4

A Step 3: Power supply

CP2004 (pins 1, 2)
12 V input

No Check the wire between OK

Is the voltage of 12 V? Check the MAIN Assy.
D-MAIN and MAIN Assemblies.

Yes
IC2008 (pin 2)
12 V input

No Check the IC2008 and NG

B Is the voltage of 1.2 V input? Replace IC2008.
its peripheral circuits.

Yes
L2008

No No Check the peripheral circuits or the OK

Is the voltage of 5 V output? Is pin 7 (en) of IC2008 high? Replace IC2008.
MAIN microcomputer (IC2023).

Yes
Yes

Check the IC2011 power pin (dvdd and

avdd): dvdd: 5 V, avdd: 5 V.
C
OK
+5V line of D-MAIN Assy is OK.

Step 4: X'tal
IC2011 (pins 6, 7)

Is there a 24.576 MHz No Check the IC2011 and its peripheral

output? circuits or replace XTAL2002.
D
Yes
IC2014 (pin 2)

Is there a 24.576 MHz No Check the IC2014 and its peripheral

input? circuits or replace IC2011.

Yes
To Step 5

18 VSX-522-K
1 2 3 4
 5 6 7 8

Step 5: DIR A
Check that the S/PDIF signal is input.
Check that changes by pulling out and inserting the digital input lines.

IC2009 (pin 3) opt

Can observe the No Check the path to INPUT pin of

digital signal? JACK2006 or replace JACK2006.
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 61)

B
Can observe the No Check the pass to IC2009 pin 4
digital signal? or replace IC2009.
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 67)
coax

Can observe the No Check the path to pins 8 to 11 of

digital signal? IC2009 or replace IC2009.
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 69)
HDMI C

Can observe the No Check the path to pin 5 of IC2009 or

digital signal? replace IC2009.
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 59)
ARC

Can observe the No Check the path to pins 1, 12 of

digital signal? IC2009 or replace IC2009.
(0 V ↔ 3.3 V)
Yes
D
SPDIF INPUT line is OK.

Check that the data and clock signals are output.

IC2011 (pin 10)

DIR_MCK (master clock)

No No No Check the IC2023 and

Is there a master clock Is the voltage of PDN IC2011 Check the pin 58 of IC2023, its peripheral circuits or
24.576 MHz output? is the voltage 3.3 V?
pin 31 3.3V? replace IC2023.
(0 V ↔ 3.3 V)
Yes Yes
E
Check the peripheral circuits
IC2011 (pin 16) DIR_LRCK (LR CLOCK) between IC2011 and IC2023.

No Check the IC2011 and its peripheral OK Check the IC2014 and its peripheral OK
Is there a LR clock Replace IC2011, IC2014.
output? circuits of IC2011. circuits of IC2014.
(0 V ↔ 3.3 V)
Yes

VSX-522-K 19
5 6 7 8
 1 2 3 4

A
A

IC2011 (pin 14) DIR_SDTO (DATA)

No Check the IC2011 and its peripheral OK

Is there a DATA output? Replace IC2011.
circuits of IC2011.
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 15)
DIR_BCK (bit clock)

B
No Check the IC2011 and its peripheral OK Check the IC2014 and its peripheral OK
Is there a bit clock output? Replace IC2011, IC2014.
circuits of IC2011. circuits of IC2014.
(0 V ↔ 3.3 V)
Yes
SWITCH

IC2014 (pin 4)
DAI_MCK (MASTER CLOCK)

Is there a master clock No No Check the path between IC2014 pin 1

Is the voltage of IC2014
24.576 MHz output? pin 1 0 V? and IC2023 pin 70.
(0 V ↔ 3.3 V)
C Yes Yes
*IC2014 pin 1
DIR output is OK. 0 V: DIR
Replace IC2014.
3.3 V: HDMI

Step 6: ADC
Check that the ANALOG input to DSP mode.

CN2003 (pins 1, 3) ANALOG AUDIO input

No Is there a analog No
Is there a analog audio audio signal of BRG-A Assy Check the AUDIO Assy.
D signal? CP403 pins 17, 19?

Yes

Replace CP2003 wafer of BRG-A Assy,

or reconnect BRG-A Assy.

Yes
IC2011 (pin 17)
ADC_SDTO (ADC AUDIO OUT)

Is there a data No
output?
(0 V ↔ 3.3 V)
E Yes
IC2011 (pin 18) DSP_BCK

Is there a bit clock No

3.072 MHz input?
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 19) DSP_LRCK

Is there a LR clock No
F 48 kHz input?
(0 V ↔ 3.3 V)
Yes
Check the path between IC2016 and data & address lines.
To Step 7 SDRAM (IC2018), FLASH ROM (IC2019), replace IC2016.

20 VSX-522-K
1 2 3 4
 5 6 7 8

Step 7: DSP mode audio output A

Digital output of each CH when inputting the digital signal with audio.

IC2011(pin 18)
DSP_BCK (BIT CLOCK)

No
Is there a bit clock input?

(0 V ↔ 3.3 V)
Yes
IC2011 (pin 19)
DSP_LRCK (LR CLOCK)

B
No
Is there a LR clock
output?
(0 V ↔ 3.3 V)
Yes
IC2011 (pin 28)
front L/R data

No
Is there a data input?

(0 V ↔ 3.3 V)
Yes
IC2011 (pin 27)
surround L/R data
C

No
Is there a data input?

(0 V ↔ 3.3 V)
Yes
IC2011 (pin 26)
CENTER/LFE data

No
Is there a data input?

(0 V ↔ 3.3 V)
Yes
surround back L/R data D
IC2011 (pin 25)
or front hight L/R data

No
Is there a data input?

(0 V ↔ 3.3 V)
Yes
To Step 8 Check the path between IC2016 and data & address lines.
SDRAM (IC2018), FLASH ROM (IC2019), replace IC2016.

VSX-522-K 21
5 6 7 8
 1 2 3 4

A Step 8: CODEC output (ANALOG AUDIO OUT)

Analog output of each CH when inputting the digital signal with audio.

Analog output of each CH when inputting

the digital signal (-∞ dB(no signal)).

IC2011 (pin 49) IC2011 (pin 49)

front R out front R out

Is there a audio signal No No

B Is the output 2.5 V fixing?
output?

Yes Yes
IC2011 (pin 47) IC2011 (pin 47)
front L out front L out

Is there a audio signal No No

Is the output 2.5 V fixing?
output?

Yes Yes
IC2011 (pin 45) IC2011 (pin 45)
surround R out surround R out

C
Is there a audio signal No No
Is the output 2.5 V fixing?
output?

Yes Yes
IC2011 (pin 43) IC2011 (pin 43)
surround L out surround L out

Is there a audio signal No No

Is the output 2.5 V fixing?
output?

Yes Yes
IC2011 (pin 41) IC2011 (pin 41)
center out center out
D

Is there a audio signal No No

Is the output 2.5 V fixing?
output?

Yes Yes
IC2011 (pin 39) IC2011 (pin 39)
LFE out LFE out

Is there a audio signal No No

Is the output 2.5 V fixing?
output?

Yes Yes
E
End
Replace IC2011.

22 VSX-522-K
1 2 3 4
 5 6 7 8

A
[2] HDMI TROUBLESHOOTING

HDMI Troubleshooting
Cause for noncomplection of HDMI authentication between the source equipment and this unit.
(the HDMI indicator is unlit or flasher)

HDMI Simple Diagnosis

Causes for no display or sound from the monitor

OK
Replace the HDMI cable. Replace the HDMI cable.
B

NG
OK
Connect the source equipment Repare the Receiver.
(player) to the Sink equipment
(monitor) directly.

NG
OK
Replace the Player. Repare the Player.
C

NG
OK
Replace the Monitor. Repare the Monitor.

Step 0: Preliminary confirmation Step 1: Connect the HDMI equipment

Confirm the following items before checking Source equipment:
Connect a DVD player to DVD or SAT/CBL or GAME or BD

D
Do screws of back chassis No
Tighten screws securely. Sink equipment:
securely tighten? Connect a TV to HDMI OUT

Yes

To Step 1 POWER ON

Turn on the power of the receiver and equipments which was

connected with HDMI.

Function switch (DVD or SAT/CBL or GAME or BD)

E

Switch the function that HDMI was assigned.

Factory shipments setting:
HDMI1: DVD
HDMI2: SAT/CBL
HDMI3: GAME
HDMI4: BD

To Step 2

VSX-522-K 23
5 6 7 8
 1 2 3 4

A Step 2: Power supply

IC2004 (pin 1)
S+3.3V_ON

No Check the pin 73 of IC2023. No Check the IC2023 and its

Is the voltage 0 to 3.3 V? Is the voltage 0 to 3.3 V? peripheral circuit or replace IC2023.
Yes
Yes
Check the circuit between
IC2023 and IC2004 .

IC2004 (pin 4)
B

No Is pin 5 of IC2004 No Check the parts and pattern in

Is 3.3 V output voltage?
an above 6 V? the path. (CN704B pins 18, 19)

Yes D+12V Yes

CP2004 (pins 1, 2) Replace IC2004.

No
Is the voltage 12 V? Diagonose the MAIN Assy.

Yes DMAIN+5V
C
L2008

No No Diagonose the MAIN

Is the voltage 5 V? Is pin 7 (en) of IC2008
microcomputer (IC2023).
high?

Yes DMAIN+3.3V Yes

L2007 Replace IC2008.

No No Diagonose the MAIN

Is the voltage 3.3 V? Is pin 7 (en) of IC2007
microcomputer (IC2023).
high?
D
Yes H+1.8V on/off Yes
IC2005 (pin 1) Replace IC2007.

No Check the parts and pattern in

Is the voltage 3.3 V?
the path. (IC2023 pin 55)

Yes H+1.8V
IC2005 (pin 5)

No No Diagonose the MAIN

Is the voltage 1.8 V? Is the IC2005 pin 1 high?
E microcomputer (IC2023).

Yes Yes
To Step 3 Replace IC2005.

24 VSX-522-K
1 2 3 4
 5 6 7 8

Step 3: Diagnosis Step 5: INPUT/OUTPUT Diagnosis A

Each data lines confirmation checks it after standby off/on.
* when connected the equipment
to IN1 (DVD):
IC2023 (pin 77) JACK2000 (pin 18)
SUB_RST +5V_R3

Repeat
No Diagonose the MAIN No Check the JACK2000.
Is the voltage 0 to 3.3 V? microcomputer (IC2023). Is the voltage 5 V? If JACK2000 is failure,
replace JACK2000.
Yes Yes
IC2023 (pin 80) JACK2001 (pin 18)//+5V_R2//IN2 (SAT/CBL)
CSCK_MAIN
JACK2002 (pin 18)//+5V_R1//IN3 (GAME)
JACK2003 (pin 18)//+5V_R0//IN4 (BD)
B
No Diagonose the MAIN Yes
Is there a data output?
microcomputer (IC2023).
(0 to 3.3 V) To Step 6

Yes
IC2023 (pin 79)
SCDO_MAIN
Step 6: Hot Plug Detect
Is there a data input No Diagonose the MAIN
and output? (0 to 3.3 V) microcomputer (IC2023) and IC2001 JACK2004 (pin 19)
hot plug detect signal input

Yes
No Check the JACK2004.
IC2000 (pin 94) Is the voltage 5 V? If JACK2004 is failure,
EXT_RSTb
replace JACK2004. C
Yes
Is the voltage 0 to 3.3 V? No Check the parts and patterns
IC2001 (pin 29)
in the path pin 53 of IC2001.

Yes
No Check the pattern and
To Step 4 Is the voltage 5 V? parts.

Yes
JACK2000 (pin 19)
Step 4: X'TAL HP_DET

IC2001 (pin 41) Check the JACK2000.

No D
Is the voltage 5 V? If JACK2000 is failure,
replace JACK2000.
No Replace IC2001 or Yes * when connected the equipment
Is there a 24 MHz input? XTAL2000. to IN1 (DVD):
JACK2000 (pin 19)
HPD1
Yes
Repeat

IC2001 (pin 42) Check the JACK2000 and

Is the voltage 5 V when No IC2000. If JACK2000 or
selecting IN1? IC2000 failure, replace
JACK2000 or IC2000.
No Check the path to pin 42 of Yes
Is there a 24 MHz output?
IC2001. Replace IC2001.
JACK2001 (pin 19)//+5V_R2//IN2 (SAT/CBL)
JACK2002 (pin 19)//+5V_R3//IN3 (GAME)
Yes JACK2003 (pin 19)//+5V_R4//IN4 (BD) E
IC2000 (pin 97) Yes
To Step 7

Is there a 18.432 MHz No Replace IC2000 or

input? XTAL2001.

Yes
IC2000 (pin 98)

Is there a 18.432 MHz No Check the path to pin 98 of

output? IC2000. Replace 2000.
F
Yes
To Step 5

VSX-522-K 25
5 6 7 8
 1 2 3 4

A Step 7: SDA /SCL Step 8: TMDS

IC2001 (pin 7) IC2000 (pins 67,68,70,71,72,73,75,76 )

DDC_SDA (HDMI_OUT) TMDS OUTPUT

check the JACK2004 and

No Are there signals No Check the IC2000.
Does a signal output IC2001. If JACK2004 or
in constant period (approx. 0.5 Vp-p) If IC2000 is failure, replace
IC2001 is failure, replace
(0 to 5 V)? IN all lines? IC2000
JACK2004 or IC2001.
Yes Yes
IC2001 (pin 6) End
DDC_SCK (HDMI_OUT)

B Check the JACK2004 and

Does a signal output No IC2001. If JACK2004 or
in constant period IC2001 is failure, replace
(0 to 5 V)? JACK2004 or IC2001.
Yes
IC2001 (pin 5)
HSDA

No Check the IC2000, IC2001

Is the voltage 0 to 3.3 V? and IC2003. If they are
failure, replace them.

Yes
IC2001 (pin 4)
C HSCL

No Check the IC2000, IC2001

Is the voltage 0 to 3.3 V? and IC2003. If they are
failure, replace them.

Yes * when connected the equipment

to IN1 (DVD):
IC2000 (pin 114)
DDC0_SDA (HDMI IN1(DVD))

Check the IC2000 and

Repeat

Is there a same signal No JACK2000. If IC2000 or

as IC2000 pin 121 when JACK2000 is failure, replace
selecting IN1? IC2000 or JACK2000.
(0 to 5 V)
Yes
D
IC2000 (pin 115)
DDC0_SCL (HDMI IN1(DVD))

Check the IC2000 and

Is there a same signal No JACK2000. If IC2000 or
as IC2000 pin 122 when JACK2000 is failure, replace
selecting IN1? IC2000 or JACK2000.
(0 to 5 V)
Yes
JACK2001 (pin 18)//+5V_R2//IN2 (SAT/CBL)
JACK2002 (pin 18)//+5V_R1//IN3 (GAME)
JACK2003 (pin 18)//+5V_R0//IN4 (BD)
Yes
To Step 8
E

26 VSX-522-K
1 2 3 4
 5 6 7 8

Step 9: HDMI AUDIO A

*play is Dolby thru HD @ dts master audio source

HDMI audio MASTER clock

IC2000 (pin 109)
output

Is there a 24.576 MHz No

output?
(0 V ↔ 3.3 V)
Yes
IC2000 (pin 110) HDMI audio BIT clock output

No B
Is there a 12.28 MHz
output?
(0 V ↔ 3.3 V)
Yes
IC2000 (pin 111) HDMI audio LR clock output

Is there a 192 kHz No

output?
(0 V ↔ 3.3 V)
Yes
*SPDIF out:Dolby digital,dts..
IC2000 (pin 106) HDMI audio SPDIF OUT * not output:Dolby thru HD & dts master audio

C
Can observe the No
digital signal?
(0 V ↔ 3.3 V)
Yes
IC2000 (pin 112) HDMI audio front L/R OUT

Can observe the No

digital signal?
(0 V ↔ 3.3 V)
Yes
IC2000 (pin 92) HDMI audio surround L/R OUT
D

Can observe the No

digital signal?
(0 V ↔ 3.3 V)
Yes
IC2000 (pin 91) HDMI audio center/sw OUT

Can observe the No

digital signal?
(0 V ↔ 3.3 V)
Yes
HDMI audio surroundback OUT
IC2000 (pin 90) E
HDMI audio front hight OUT

Can observe the No

digital signal?
(0 V ↔ 3.3 V)
Yes
Check the VDD_PLL and GND
IC2016 (pins 1, 176, 175, 174) lines. Replace IC2000.

Can observe the No Check the switching IC.

digital signal? IC2010, IC2014.
(0 V ↔ 3.3 V)
Yes
F
HDMI AUDIO is OK

VSX-522-K 27
5 6 7 8
 1 2 3 4

A
[3] iPod TROUBLESHOOTING
Step 0: iPod/USB Power supply
CP2006 (pin 1)

No Check the wire between F-USB

Is the voltage 5 V?
and D-MAIN Assemblies.

Yes
To Step 1

B
Step 1: Power supply
CP2006 (pin 1)
5 V input

No No
Is the voltage 5 V? Is pin 8 of IC2024 high? Check the F-USB Assy.

Yes Yes
iPod/USB power is OK.
Go to Step 2. Is the voltage 5 V No Check the IC2008 DC/DC
pin 2 of IC2024? convertor circuit.

Yes
C

No Check the path between

Is pin 4 (en) of IC2024 high? IC2023 (pin57).

Yes

Replace IC2004.

Step 2: Operation of iPod (Authentication process)

D_MAIN Assy
IC2016 (pins 137, 138) USB data D+,D-

D
Do D+ and D- No
communicate? Check the USB data line.

Yes
SCL, SDA
IC2021 (pins 12, 13) (I2C between IC2021 and IC2023)

Do SCL and SDA No When SCL and SDA are normal operation = high (3.3 V)
communicate? Connect iPod, and communicate it about 10 seconds later (authentication starts).
And communicate it about 60 seconds later (authentication is complete).
Yes No

Operation of IC2021 is OK. Does reset_auth (pin 4) No Check the path between
Go to Step 3. reset it?
E IC2023 (pin48).
High after the reset.
Yes

Replace IC2021.

Step 3: Audio out check

IC2016
DSP BCK, LRCK, SDINF

No
Is there a signal? Replace IC2016.

F
Yes
Refer to Step 7 of
"[1] DSP TROUBLESHOOTING."

28 VSX-522-K
1 2 3 4
 5 6 7 8

5.2 USB/iPod ERROR MESSAGE

Functional Name A
iPod ERROR MESSAGE

Outline
Error message is displayed at abnormality time.

Basic Operation
Front Key Sequence Change OSD display Time (sec) FL Display
Over Current Error B
I / U ERR 4

No Track Caution
NO TRACK

VSX-522-K 29
5 6 7 8
 1 2 3 4

5.3 DETECTION CIRCUIT

A
[1] Overload and DC Protection Circuit

B AMP5 ASSY D D-MAIN ASSY

B AMP5 ASSY

C MAIN ASSY

30 VSX-522-K
1 2 3 4
 5 6 7 8

A
[2] TEMP Protection Circuit

DD-MAIN ASSY

C
AMP5 ASSY

AMP5 ASSY
B

VSX-522-K 31
5 6 7 8
 1 2 3 4

5.4 IC INFORMATION

A
(M3030RFGPFP_256K)(D-MAIN ASSY: IC2023)
MAIN Microcomputer

• Pin Function
Pin Symbol I/O Description
1 A_MUTE O Audio output control pins at Mute Tr (active at L)
2 SB_MUTE O SB ch. Audio output control pins at Mute Tr (active at L)
3 F_RLY O Tr driven control pins at the Front speaker output Relay. (active at H)
4 S_RLY O Tr driven control pins at the Surround speaker output Relay. (active at H)
5 C_RLY O Tr driven control pins at the Center speaker output Relay. (active at H)
6 AC_VOLT_DET I AC x2 Voltage detection pin (normal: H)
B 7 RMC I Remote control signal input pin
8 BYTE I The data bus is 16 bits long when the this pin is held "L" (GND)
9 CNVSS_UP I Switches processor mode
10 24C16_SDA I/O Data signal input & output for data backup of main CPU
11 24C16_SCL O Clock signal output for data backup of main CPU
12 /RESET I Micom reset signal input pin (active at L)
13 XOUT O Output for 16 MHz Crystal
14 VSS Ground
15 XIN I Input for 16 MHz Crystal
16 VCC1 +3.3 V power supply
17 /NMI I Input pin for the NMI interrupt
18 TUNER_INT I Tuner Interrupt signal input pin
C 19 PDN I Power down signal input pin
20 OSD/FLT_DATA O OSD & FL drive IC output pin of the Data
21 MUTE_B+_CTL O Power control pin mute B+
22 VIDEO_MUTE O Not used
23 HP_DET I Monitoring the input pin headphone connection
24 OSD_CE O OSD IC enable signal output pin
25 V+5V_DET I VIDEO +5 Voltage monitor input pin DC protection
26 V_CTL_B O IC control signal B output pin for selecting the video input
27 V_CTL_A O IC control signal A output pin for selecting the video input
28 OSD/FLT_CLK O OSD & FL drive IC output pin of the Clock
29 H+3.3V_FETON O Not used
30 H+5V_FETON O Not used
31 232_RX/U_TX O Output for Upgrade (UART)
D
32 232_TX/U_RX I Input for Upgrade (UART)
33 SCLK_JTAG I Serial clock input pin
34 BUSY_JTAG O BUSY signal output pin
35 2162_SDA I/O MFI IC serial data I/O PIN
36 2162_SCL I/O MFI IC transfer clock I/O PIN
37 D+5V_FETON O Not used
38 D+3.3V_FETON O Not used
39 OSD_RST O OSD IC Reset signal output pin
40 TUNER_SCLK O Clock signal output for Tuner Pack
41 EPM_UP I Upgrade
42 TUNER_SDIO I/O Data signal input & output for Tuner Pack
43 TUNER_SEN O Output for Tuner Pack Serial Enable Input (active at L)
E 44 TUNER_RST O Output to reset Tuner Pack (active at L)
45 TR_DET I Output for HDMI_HD / SACD_DSD Select (L: HDMI_HD, H: SACD_DSD)
46 CE O Upgrade
47 2162_PWR O MFI IC pin of the power control
48 2162_RST O MFI IC Reset signal output pin
49 VOL_DATA O Data signal output for R2A15219 (I2C)
50 VOL_CLK O CLK signal output for R2A15219 (I2C)

32 VSX-522-K
1 2 3 4
 5 6 7 8

A
• Pin Function
Pin Symbol I/O Description
51 SW_SUM O Output for Sub Woofer SUMMING Control (H: SUMMING)
52 MIC_DET I Monitoring the input pin microphone connection (detection: L)
53 HP_RLY O Headphone audio output control pins at Mute Tr (active at L)
54 DSP+3.3_FETON O DSP 3.3 V Power on/off control pin (on: H)
55 H+1.8V_ON O Control pin HDMI IC +1.8 V REG. IC (on: H)
56 D+3.3V_ON O Control pin digital +3.3 V DC/DC IC (on: H)
57 D+5V_ON O Control pin digital +5 V DC/DC IC (on: H)
58 4588_PDN O Output for AK4588 power down
59 4588_SDA O Data signal output for AK4588 (I2C)
60 4588_SCL O Clock signal output for AK4588 (I2C)
B
61 DSP_SIMO O Data signal output for DA808 (SPI)
62 VCC2 +3.3 V power supply
63 DSP_SPICLK/B7 O Clock signal output for DA808 (SPI)
64 VSS Ground
65 DSP_RST O Output to reset DA808
66 USB5V_DET I USB+5 Voltage monitor input pin overcurrent protection.
67 DSP_SOMI I Data signal Input from DA808
68 DSP_SPICS O Chip select signal output for DA808
69 DSP_SPIEN I SPI Enable signal input from DA808
70 HDMI_SEL O IC signal of the control pins at select HDMI or analog audio
71 PROTECT2 I AMP Assy input signal of the RADIATOR THERMAL pin (L = PROTECTION)
72 MAIN_IRQ O Interrupt Output to sub CPU
73 S+3.3V_ON O Output for sub CPU Power ON/OFF cotrol pin C
74 SUB_IRQ I Interrupt Iuput from sub MICOM
75 HDMI_AMUTE I Input for HDMI_RX_MUTE condition
76 USB5V_ON O Output for power down of SUB microcomputer
77 SUB_RST O Output to reset sub CPU
78 DSD_SEL O Output for DSD audio signal selector ic contol pin.
79 SCDO_MAIN O Data signal output to SUB microcomputer
80 CSCK_MAIN O Clock signal output for SUB microcomputer
81 SET OPTION I Input for Set option
82 STEP OPTION I Input for Step (Group) option
83 NC O Not used
84 NC O Not used
85 PROTECT1 I AMP Assy Protection detection signal input pin (ASO = 0.82 V, DC = 1.39 V) D
86 VOL_DN I Data input for VOLUME encoder (VOLUME DOWN is counterclockwise direction)
87 VOL_UP I Data input for VOLUME encoder (VOLUME UP is clockwise direction)
88 IN_DN I Data input for INPUT selector encoder
89 NC I Not used
90 KEY1 I Data input for Key1 scan
91 KEY3 I Data input for Key3 scan
92 KEY2 I Data input for Key2 scan
93 IN_UP I Data input for INPUT selector encoder
94 FLT_CE O Output for chip enable of SC16315
95 NC O Not used
96 GND Ground
97 NC O Not used E
98 VREF Reference voltage (Connected to +3.3 V)
99 AVCC +3.3 V power supply
100 STBY_RLY O Output to ST-BY Relay ON/OFF (active at H)

VSX-522-K 33
5 6 7 8
 1 2 3 4

A
(EPF021A)(D-MAIN ASSY: IC2001)
SUB Microcomputer

• Pin Function
Pin Symbol I/O Description
1 NC I Not used
2 CSCK_MAIN I Clock signal input from MAIN microcomputer
3 SCDO_MAIN I Data signal Input from MAIN microcomputer
4 HSCL O IIC clock signal output pin (EP94A1K & EPF011C)
5 HSDA I/O IIC data signal in/output pin (EP94A1K & EPF011C)
6 DDC_SCK O IIC clock signal output pin for HDMI output jack
B 7 DDC_SDA I/O IIC data signal in/output pin for HDMI output jack
8 VDD +3.3 V power supply
9 GND Ground
10 NC I Not used
11 NC I Not used
12 VDD +3.3 V power supply
13 NC I Not used
14 NC I Not used
15 SUB_RST I SUB microcomputer reset signal input pin
16 SUB_OPO I Chip operation mode select signal input pin (0: normal)
17 GND Ground
18 NC I Not used
C 19 NC O Not used
20 NC O Not used
21 NC O Not used
22 NC O Not used
23 NC O Not used
24 NC O Not used
25 NC O Not used
26 NC O Not used
27 NC O Not used
28 NC O Not used
29 HPD_IN I HDMI Hot plug detect signal input pin
30 NC I Not used
31 NC I Not used
D
32 NC I Not used
33 NC I Not used
34 NC I Not used
35 MAIN_IRQ I Interrupt sinal Input pin from MAIN microcomputer
36 SUB_IRQ O Interrupt signal output pin to MAIN microcomputer
37 THRU_LED O HDMI LED on/off control pin
38 NC O Not used
39 VDD +3.3 V power supply
40 GND Ground
41 XIN I Input for 24 MHz Crystal
42 XO O Output for 24 MHz Crystal
43 VDD +3.3 V power supply
E 44 GND Ground
45 NC O Not used
46 NC O Not used
47 CEC_MCU_RST O CEC microcomputer Reset signal output pin
48 NC I Not used
49 HT0_CTLB O Hot plug detect signal output pin (DVD FUNCTION)
50 HT1_CTLB O Hot plug detect signal output pin (SAT/CBL FUNCTION)

34 VSX-522-K
1 2 3 4
 5 6 7 8

A
• Pin Function
Pin Symbol I/O Description
51 HT2_CTLB O Hot plug detect signal output pin (GAME FUNCTION)
52 HT3_CTLB O Hot plug detect signal output pin (BD FUNCTION)
53 EP94A1K_RST O Reset signal output pin for EP94A1K IC
54 NC O Not used
55 NC O Not used
56 NC I Not used
57 NC I Not used
58 CEC MCU_IIC_SCL O IIC clock signal output pin for CEC microcomputer
59 CEC MCU_IIC_SDA I/O IIC data signal in/output pin for CEC microcomputer
60 NC I Not used
B
61 NC I Not used
62 SUB_RXD I Soft update UART comunication data input pin (UPDATE JIG B'D)
63 SUB_TXD O Soft update UART comunication data output pin (UPDATE JIG B'D)
64 INTb I Interrupt signal input pin from EP94A1K & EPF011C

(EPF011C)(D-MAIN ASSY: IC2003)

CEC Microcomputer

• Pin Function
Pin Symbol I/O Description
1 RXD I Soft update UART comunication data input pin (UPDATE JIG B'D) D
2 TXD O Soft update UART comunication data output pin (UPDATE JIG B'D)
3 CECin I HDMI CEC signal input pin
4 DDC_SCL I IIC clock signal input pin from SUB microcomputer
5 DDC_SDA I/O IIC data signal in/output pin from SUB microcomputer
6 SCL I IIC clock signal input pin (EP94A1K & EPF011C)
7 SDA I/O IIC data signal in/output pin (EP94A1K & EPF011C)
8 RSTb I CEC microcomputer Reset signal input pin
9 OP_MODE I Chip operation mode select signal input pin(0:normal)
10 IO3 − Not used (PULL_UP)
11 IO2 − Not used (PULL_UP)
12 INTb I Interrupt signal input pin from EP94A1K
13 A0 − Ground
E
14 A1 − Ground
15 A15 − Ground
16 VDD +3.3 V power supply
17 VSS Ground
18 XIN I 24 MHz Crystal input
19 XO O Not used
20 VDD +3.3 V power supply
21 VSS Ground
22 CECO O HDMI CEC signal output pin
23 A6 − Ground
24 BIST − Ground

VSX-522-K 35
5 6 7 8
 1 2 3 4

A
J005253200020-IL (W25Q32BV_SS1G)(D-MAIN ASSY: IC2019)
32M-bit Serial Flash Memory with uniform 4KB sectors and Dual/Quad SPI

• Pin Arrangement (Top View)

/CS 1 8 VCC

DO(IO1) 2 7 /HOLD(IO1)
B

/WP(IO2) 3 6 CLK

GND 4 5 DI(IO0)

• Pin Function
No. Pin Name I/O Function
1 /CS I Chip select input
C
2 DO(IO1) I/O Data output (Data input output 1) *1
3 /WP(IO2) I/O Write protect input (Data input output 2) *2
4 GND Ground
5 DI(IO0) I/O Data input (Data input output 0) *1
6 CLK I Serial clock input
7 /HOLD(IO0) I/O Hold input (Data input output 3) *2
8 VCC Power supply

*1 IO0 and IO1 are used for Standard and Dual SPI instructions.
*2 IO0 - IO3 are used for Quad SPI instructions.

36 VSX-522-K
1 2 3 4
 5 6 7 8

A
J127410500010-IL (NJM41050V)(VIDEO ASSY: IC1200)
47µF AC-Coupling Capacitor 3-Input 1-Output Video Driver with LPF

• Pin Arrangement (Top View)

Vin1 1 14 NC

SW1 2 13 SSIGV
Vin2 3 12 Vsag
SW2 4 11 SREFV

Vin3 5 10 Vcc
B
Mute 6 9 GND
NC 7 8 Vout

• Block Diagram

VSX-522-K 37
5 6 7 8
 1 2 3 4

6. SERVICE MODE
6.1 SERVICE MODE
A
[1] Display mode for numbers of protection detections
[Purpose]
The numbers of detections for various protection processes are displayed.

[How to enter/exit]
During Standby mode, simultaneously press and hold the [PRESET k] and [STANDBY/ON] keys for 2 seconds to enter
this mode.
The display will return to the normal indication when no key operation is performed for 5 seconds.

B [Basic operations]

Key Operation FL Display Time (sec.) Description of Indications

(STANDBY state)

[PRESET k] +
[STANDBY/ON] keys
*2 5 (-> normal) *1 Number of DC error detections
(Initial display)
Counter
[ENTER] key
C
*2 5 (-> normal) *1 Number of OVERLOAD error detections
[ENTER] key Counter
*2 5 (-> normal) *1 Number of abnormal-temperature
[ENTER] key error detections
Counter

(Initial display)

*1 "5 (-> normal)" denotes that the display will return to the normal indication when no key operation is performed
for 5 seconds.
*2 Variable range: 0 to 255
D

The above-mentioned Display mode is available only when the product operates properly.

If any protection function is activated while the product is in use, the product cannot be turned ON and enter the above
Display mode. In such a case, cancel the protection function, referring to “3.4 How to cancel the status after detection of the
DC error." If a protection function is activated immediately after the previous protection function is canceled, cancel that
protection function again then enter STBY mode immediately. You can then see the error logs, following the above procedures,
until a next protection function is activated.

38 VSX-522-K
1 2 3 4
 5 6 7 8

A
[2] Reset mode for numbers of protection detections
[Purpose]
For clearing all the counts of protection detections.
(This mode resets the counts of protection detections.)

[How to enter/exit]
During Standby mode, simultaneously press and hold the [ALC/STANDARD SURR] and [STANDBY/ON] keys
for 10 seconds to enter this mode.
The display will return to the normal indication when no key operation is performed for 5 seconds.
B
[Basic operations]

Key Operation FL Display Time (sec.) Description of Indications

(STANDBY state)

[ALC/STANDARD SURR]
+ [STANDBY/ON] keys
5 (-> normal) *1
(press and hold the keys
for 10 seconds.)
[ENTER] key
C

(Counter Clear end) 5 (-> normal) *1

(Normal display) usually

*2

*1 "5 (-> normal)" denotes that the display will return to the normal indication when no key operation is performed
for 5 seconds.
*2 Indication when the BD function is selected
D

[Detailed explanations]
1. When the procedures for Reset mode for numbers of protection detections are completed, all the counters will be
reset to "000."
2. Prohibitions:
The protection detection counts cannot be cleared (reset to 000) with the MEMORY CLEAR process.
They can only be cleared when the procedures of Reset mode are completed.

VSX-522-K 39
5 6 7 8
 1 2 3 4

A
[3] The unit’s operation when a error is detected
[Purpose]
• The unit’s operation when a DC/OVER/TEMP error is detected is described here.
• How to cancel the status after detection of a DC error is described here, because no key input will be accepted after
a DC error detection.
[Basic operations]
3.1 DC (AMP is abnormality) error detection
Key Operation FL Display Time (sec.) Description of Indications
B
(Normal display) usually Normal display

(DC detection)
(Auto)
(RECEIVER POWER OFF)
*1, *2

3.2 OVERLOAD (overcurrent) error detection

C
Key Operation FL Display Time (sec.) Description of Indications

(Normal display) usually Normal display

(OVERLOAD detection)
(Auto)
(RECEIVER POWER OFF)
*1

40 VSX-522-K
1 2 3 4
 5 6 7 8

3.3 TEMP (AMP overheat) error detection

For detection of a TEMP error, the unit monitors both the TR_DET and PROTECT2 signals. If a TEMP error is detected,
the processes shown below will be performed. The processes shown below are rough operational specifications and are
not the actual commands from the mounted components.
After a TEMP error is detected, the count of protection activation detections will be updated.

Counter: Temp2 TR_DET Counter: Temp1 PROTECT2

P6_4 (34 pin) PL2_1 (71 pin)
(TRTHER_DET from AMP Assy) (RADI_DET from AMP Assy)

B
Normal Operations Normal Operations
*1 *3

No No
Is TR_DET detected? PROTECT2 detected?

Yes Yes

MUTE ON and ALL Speakers/

Is the VOL value 5 Yes Phones Relay are set to OFF.
Have "OVERHEAT" flashing
or less? on the FL display for 3 sec.
C
No
Deduct 3 from the current VOL POWER OFF (STBY) Timer START is performed
value. Have "TEMP" flashing for 3 sec.
on the FL display for 3 sec.

No After 3 sec,
Prohibit detection of PROTECT 2 is rechecked.
TR_DET for 2 min. Is PROTECT 2 detected?
*2
Yes
POWER OFF (STBY)
No Detection of TR_DET Yes
is resumed after 2 min. D
Is TR_DET detected?

*1: The detection interval must be 1 sec or less. *3: The detection interval must be 1 sec or less.
*2: If PROTECT 2 is detected while TR_DET detection
is prohibited for 2 min, the PROTECT 2 function will
be activated.

3.4 How to cancel the status after detection of the DC error

Key Operation FL Display Time (sec.) Description of Indications
E
(STANDBY state)
[ADVANCED SURROUND]
+ [STANDBY/ON] keys
(press and hold the keys
for 2 seconds.)

(Normal display) usually Normal display

[Detailed explanations] Simultaneously holding the [ADVANCD SURROUND] and [STANDBY/ON] keys on the
front panel pressed for 2 seconds will cancel Key Input Inhibition mode after a DC error
detection and turn the unit ON. F

VSX-522-K 41
5 6 7 8
 1 2 3 4

7. DISASSEMBLY

A Note:
(1) Even if the unit shown in the photos and illustrations in this manual may differ from your product, the
procedures described here are common.
(2) For performing the diagnosis shown below, the following jigs for service is required:
• 9P extension jig cable (GGD1739)
• Board to board extension jig cable (GGD1756)
• Board to board extension jig cable (GGD1798)
• Board to board extension jig cable (GGD1799)

B
1. Discharging
[1] MAIN Assy Capacitor (C55, C58)
[Procedures]
(1) Unplug the power cord.
(2) Disconnect the 10P connector from CP403 of the AMP5 Assy between CN3 of the MAIN Assy.
(3) Connect +B and –B terminal of the D7, using resistor leads with 47 - 100 ohms (2 W or higher), for discharging.
∗ Discharging time: 30 - 60 seconds, depending on the level of resistance.
(4) Check that the voltage between the +B and –B terminals is less than 1 V, using a tester.
∗ Be sure to connect the GND terminal of the tester to the chassis.
∗ If the voltage is still 1 V or higher, repeat Step (3).
C

AMP5 Assy MAIN Assy

C58 C55
CP403
–B +B

D7

D
47 - 100 ohms
(2 W or higher)

[2] FL-30 V Capacitor (MAIN Assy C101)

[Procedures] 47 - 100 ohms
(1) Unplug the power cord. (2 W or higher)
(2) Connect –30V and GND terminal of the BRG-C Assy,
using resistor leads with 47-100 ohms (2 W or higher),
for discharging.
∗ Discharging time: 5 - 10 seconds, depending on the
E
level of resistance.
(3) Check that the voltage between the –30V terminal is less
than 1 V, using a tester.
∗ Be sure to connect the GND terminal of the tester to
the chassis.
∗ If the voltage is still 1 V or higher, repeat Step (2). −30V GND

BRG-C Assy
42 VSX-522-K
1 2 3 4
 5 6 7 8

A
2. Notes on Ground Points Connection

[Note]
During repair, before checking the MAIN Assy, etc., with the rear chassis removed, be sure to connect the
GND terminal of the main capacitor to the back chassis (speaker chassis), as shown below, then connect the
power cord.

Without grounding connection, the protection circuit will be activated.

After repairing, be sure to remove the ground wire before reassembling.
B

GND wire
(Be sure to disconnect the GND wire
before reassembly.)
Speaker chassis
Back chassis

Main capacitor GND

MAIN Assy (SIDE B)

VSX-522-K 43
5 6 7 8
 1 2 3 4

A 3. Disassembly

[1] Front Panel Section

Remove the cabinet by removing the 10 screws.

(1) Remove the five screws. (BBZ30P080FTB)

B
1 1 1 1 1
• Bottom view

(2) Remove the two screws.

(1500001206010-IL)

2 2

(3) Unhook the two hooks.

3 3

(4) Arrange the front panel section as shown

E in the photo below. Front panel section

44 VSX-522-K
1 2 3 4
 5 6 7 8

A
[2] Heatsink Section
Caution: Heatsink section in work becomes hot,
and be careful with it.
Remove the cabinet by removing the 10 screws.

(1) Remove the three screws. (BBZ30P080FTC) 1 1 1

• Bottom view

(2) Remove the six screws. (BBZ30P080FTC) G-L Assy G-R Assy

2
2 C

2 2
2 2

(3) Disconnect the one connector. (CP401)

(4) Cut the binder.
(5) Remove the one screw. (BBZ30P080FTC) WG-A Assy
(6) Remove the WG-A Assy. 6 D

4 5

CP401
3

D-MAIN Assy AMP5 Assy

(7) Connect the extension jig cable. 7 Extension jig cable (GGD1739) AMP5 Assy Heatsink
(8) Rotate the heatsink section in the direction of
the arrow.

CP401

8
F

VSX-522-K 45
5 6 7 8
 1 2 3 4

A
[3] D-MAIN Assy
Remove the cabinet by removing the 10 screws.

(1) Remove the three screws. (BBT30P100FTB)

(2) Remove the five screws. (BSZ30P040FTB) Back chassis
2 ×5 1 1

• Rear view

(3) Cut the two binders.

(4) Disconnect the three B to B connectors.
C (CN2001 to CN2003)
(5) Remove the D-MAIN Assy. BRG-A Assy

5 4
3
BRG-C Assy 3
CN2003
4
CN2001
4
CN2002
D
D-MAIN Assy

(6) Connect the three extension jig cables.

(7) Arrange the D-MAIN Assy in the photo below. 6 Borad to board extension D-MAIN Assy 8 Insulation sheet
(8) Insert any insulation sheet. jig cable (GGD1798)

Note:
15 pin connector on GGD1798 is not used in this
CN2002
E case.
9 pin connector on GGD1756 is not used in this
CN2001
case.
CN2003

7 CP2003
CP2002

CP2001

F
6 Borad to board extension 6 Borad to board extension
jig cable (GGD1799) jig cable (GGD1756)

46 VSX-522-K
1 2 3 4
 5 6 7 8

A
[4] MAIN Assy
Remove the cabinet by removing the 10 screws.

[4-1] Back chassis, D-MAIN Assy Back chassis

2 ×5 1 1
(1) Remove the 13 screws. (BBT30P100FTB)
(2) Remove the five screws. (BSZ30P040FTB)
(3) Remove the D-MAIN Assy. 1
(See procedure [3].) 1
1
1 1
1 B
1 1
1 1 1

[4-2] MAIN Assy

(1) Remove the four screws. (BBZ30P180FTC)
(2) Remove the two screws. (BBZ30P080FTC) 2
(3) Cut the four binders. 3 ×3
1
1
C

1 3
2
1

BRG-C Assy MAIN Assy WG-B Assy

(4) Remove the four screws. (BBZ30P080FTC) D

MAIN Assy
4 4 4 4

(5) Arrange the unit as shown in the photo below.

E
(6) Connect the chassis ground.
See “2. Notes on Ground Points Connection”.

F
MAIN Assy

VSX-522-K 47
5 6 7 8
 1 2 3 4

A [4-3] Regulator ICs and Recifier diode

(1) Remove the support.
(2) Tighten then loosen the screw in each of the Screwdriver
four holes for temporary joining that are
located on the rear side of the main chassis.
(This is for shaving the thread grooves to 1
facilitate attachment in the next step.)

2 2 2 2

B
Main chassis Support

C
(3) Attach the three regulator ICs and a rectifier MAIN Assy
diode to the holes tapped in Step (2).
Be sure to place them in a direction
perpendicular to the board and take care that
the jumper wires will not become distorted.

3 3 3 3

Note:
While securing the regulator ICs and rectifier diode to the holes for
temporary joining, tighten the screws while holding the regulator ICs
and rectifier diode with your fingers so that the jumper wires will not
become distorted.

48 VSX-522-K
1 2 3 4
 5 6 7 8

[4-4] Diagnosis A

(1) Connect the CP401 on the AMP5 Assy with

extension jig cable. (See procedure [2].)
(2) Reassemble the D-MAIN Assy to the rear
panel or put it on the AMP5 Assy with
extension jig cables. (See procedure [3].)
(3) Insert any insulation sheet between AMP5
Assy and MAIN Assy.

Insulation sheet

Insulation sheet

2 C
D-MAIN Assy

3
3

1
1
D

2
D-MAIN Assy BRG-C Assy MAIN Assy BRG-C Assy MAIN Assy
E

VSX-522-K 49
5 6 7 8
 1 2 3 4

8. EACH SETTING AND ADJUSTMENT

A
• If the adjustment is shifted or if it becomes necessary to readjust because of part replacement, etc., perform the
adjustment as described below.
• Any value changed in Adjustment mode will be stored in memory as soon as it is changed. Before readjustment, take note of
the original values for reference in case you need to restore the original settings.
• Use a stable AC power supply.

B
8.1 ADJUSTMENT REQUIRED WHEN THE UNIT IS REPAIRED OR REPLACED
When any of the following assemblies is replaced

AMP5 Assy "8.3 IDLE CURRENT ADJUSTMENT" (All channel)

Other assemblies No adjustment required

When any of the following parts is replaced

AMP5 Assy "8.3 IDLE CURRENT ADJUSTMENT"

(Only channel of replacement parts)

Other assemblies No adjustment required

D

Note:
Some parts on D-MAIN Assy can not be replaced due to using heat-pad connection between the board.
Please refer to [1.2 NOTES ONREPLACING PARTS], when the parts listed in the table is defective, replace whole Assy.

50 VSX-522-K
1 2 3 4
 5 6 7 8

8.2 UPDATING OF THE FIRMWARE

[Purpose] A

Refer to this section when updating the firmware of each microcomputer is required by the service information, etc.

[Necessary Tools and Connections]

1 MAIN microcomputer
• PC with a serial port
• RS-232C cable (9-pin to 9-pin, straight cable) (Marketing product)
• UPDATE jig: GGF1642 (Use FFC of GGF1642. (10P to 10P FFC))
• Firmware
Connect as shown in the figure below.
Insert the FFC with its contact surface facing the " mark.
B

10P
(MAIN microcomputer) 10P
PC
RS-232C
Straight cable
10P to 10P FFC
Rear side

UPDATE jig
GGF1642

Straight Cable Adapter JIG's side

2 HDMI (SUB) and CEC microcomputer

• PC with a USB port
• USB cable (Marketing product)
• UPDATE jig: GGF1646 (Use FFC of GGF1642. (10P to 10P FFC))
• Firmware
<PC setting> D

1. Thaw the upgrade program.zip.

Appear the below folderes and files.
Folder name: CDM20812
Folder name: EPConsole
Folder name:EPFlash_1_1_0_8
dotNetFx40_Full_setup.exe

2. Install the driver.

Request the driver at the time of the conectting the Upgrade Jig and the PC with the USB cable.
Install the Driver (CDM20812).
E
3. Install .NET Framework 3.0 service pack1.
To work EPFlash.exe (application for rewriting the HDMI u-co), request to be installed the .NET Framework 3.0 service
pack1 on the PC.
For installation of .NET Framework, Internet connection is required.

To confirm if .NET Framework 3.0 Service Pack 1 has been installed on your PC or not, select Settings > Control Panel >
Add or Remove Programs. This confirmation method may be different, depending on the PC. Refer to the operation
manual of the PC you use on how to execute Add or Remove Programs.

4. Install .NET Framwork 4.

To work EPConsole.exe , operate dotNETFx40_Full_setup.exe and install .NET Framework 4.
If .NET Framework 3.0 service pack1 doesn't install on the PC, you can not install .NET Framework 4. F
Please operate 4. after 3.
For installation of .NET Framework, Internet connection is required.

VSX-522-K 51
5 6 7 8
 1 2 3 4

A
Connect as shown in the figure below.
Insert the FFC with its contact surface facing the " mark.

PC
USB cable
(HDMI/CEC microcomputer)
10P
10P
10P to 10P FFC
UPDATE jig
GGF1646
B
Rear side

USB cable
A type <-> B type

Microcomputers update
[Procedures]
for MAIN microcomputer
1. Unplug the AC cord. [ if the following messages are displayed ]
C
Connect the FFC cable. ( MAIN microcomputer )
Start up application FlashSta on the PC.

Please push the cancel button and press the JIG's

RESET button.
And confirm a connection of FFC.
Please return to procedure 1.

4. Select the update file and enter ID.

D

2 Enter ID.
Enter "ff" in all field.

2. Plug the AC cord. (STANDBY mode)

For updating of the MAIN microcomputer, proceed with 3 Press OK button to
the following steps in STANDBY mode. go to next step.
1 Selection of upgrade file
3. Press the OK button. 1 Select the update file

Select "VSX522 Main V1xx.mot" file Press the OK button.

Select for COM port.
to update the MCU.

2 Enter ID.

Press the OK button.

52 VSX-522-K
1 2 3 4
 5 6 7 8

A
5. Set speed update and update the MCU.
1 Set speed of update.

1 Set speed of update.

Set Baud rate to 38400.

Press the OK button. B

2 Update the MCU.
E.P.R=>Erase+Program+Read
7. Unplug the AC cord.
Disconnect the FFC cable.
2 Update the MCU
Press the E.P.R … button

for HDMI (SUB) microcomputer

Press OK button. 8. Unplug the AC cord.
Start up the application EPFlash on the PC.
C
When the PC and the Upgrade Jig is connecting,
the COM PORT is set automatically.

6. Update Finished MAIN microcomputer.

9. Select "HDMI UP" on the Upgrade Jig.

Press the OK button. Press the Exit button.

Please wait for until this window
disappears.

If the following messages are displayed, shut the update Connect the PC and the Upgrade Jig. E
program down, and start the update again from step 1. Connect the FFC cable. (HDMI microcomputer )
Plug the AC cord. (STANDBY mode)
Push the JIG’s RESET button during
1 sec.
Press the OK button. 10. While holding down the tact switch of the Upgrade Jig,
press STANDBY/ON button.
After 2 or 3 seconds, release the tact switch button.
Select the 9600 of the Board rate then
press the OK button

VSX-522-K 53
5 6 7 8
 1 2 3 4

A
11. Select the update file. Press the "OpenFile" button. End the application EPFlash.

B
If the following messages are displayed, shut the update
program down, and start the update again from step 8.

Select "VSX-522_LPP_********.hex" file to update MCU.

12. Press the "START" button to update the firmware.

C

14. Turn the unit off (STANDBY mode) and unplug the
AC cord.
Disconnect the FFC cable.

for CEC microcomputer

15. Unplug the AC cord.
Start up the application EPConsole on the PC.
D
When the PC and the Upgrade Jig
are connecting, the COM PORT is Set Baud rate to 57600.
set automatically.

Rate of the progression is appeared.

13. Update Finished HDMI microcomputer.

E

16. Select "CEC UP" on the Upgrade Jig.

F
Connect the PC and the Upgrade Jig.
Connect the FFC cable. (CEC microcomputer )
Plug the AC cord. (STANDBY mode)

54 VSX-522-K
1 2 3 4
 5 6 7 8

A
17. Select the update file. Press the "FILE" button. 19. Press the button.
PC's monitor is appeared the below display. By this display,
you understand that the PC and the product are communicating.

20. Press the button to update the firmware.

Select "CECCore_ADDSEL(BB)_V***.hex" file to update MCU.

When the update file is selecting, the check box is

C
automatically on.
Rate of the progression is appeared.

21. Update Finished CEC microcomputer.

18. While holding down the tact switch of the Upgrade Jig,
D
press STANDBY/ON button.
After 2 or 3 seconds, release the tact switch button.
If the following messages are displayed, shut the update
program down, and start the update again from step 15.

E
22. Turn the unit off (STANDBY mode) and unplug the
AC cord. Disconnect the FFC cable.

Check to the software virsion of MAIN, HDMI (SUB) and CEC microcomputers
23. Make sure that the main unit is in STANDBY mode.
Press and hold the " ENTER " and " STANDBY/ON " keys, then press the " ENTER "key to display each UCOM version.
Each time the " ENTER "key is pressed, then indications on the FL display change as follows:

MAIN Ucom "ENTER" SUB Ucom "ENTER" CEC "ENTER" "ENTER"

DSP firmware All segments lit.
MAIN Xx.xx SUB zzz.zz CEC Vy,yy

F
"ENTER"

24. Turn the unit off.

VSX-522-K 55
5 6 7 8
 1 2 3 4

A DSP firmware update

[Procedures]
1. Select TV fucntion, and, with Signal select as OPTICAL1 then set the unit to STBY_Off mode.
2. Press the SPEAKERS and STANDBY/ON keys simultaneously to enter DSP UpDate mode. ("DSP UP" is displayed.)
3. When "PLAY" is displayed, playback of the .wav file starts. (Play the file only once. NEVER repeat playback.)
("PLAY" is displayed.)
4. After playback is finished and "ENTER" is displayed, press the ENTER key on the front panel. ("ENTER" is displayed.)
5. "WRITING" is automatically displayed.
6. After writing is completed, "COMPLETE" is displayed.
7. Turn the unit off then confirm that the version has been updated.

56 VSX-522-K
1 2 3 4
 5 6 7 8

8.3 IDLE CURRENT ADJUSTMENT

When any component parts which are within the red square on the following circuit diagram are replaced, the idle current
adjustment of that channel is required. (Idle current adjustment for another channel is not required.)
However, when any capacitors are replaced, the adjustment is not required.
(The following circuit diagram is for SL channel, but another channel also has same circuit diagram and same adjustment is
required)

(SL)

(SL)

Measurement Adjustment
Channel Points Points Procedure

FL
TP401 pin 1 (+)
VR401 1 Turn on the power.
TP401 pin 3 (–)
TP402 pin 1 (+) 2 Perform aging for one minute.
FR VR402
TP402 pin 3 (–)
TP403 pin 1 (+) 3 Connect a digital voltmeter to the measurement point.
C VR403
TP403 pin 3 (–)
TP404 pin 1 (+) 4 Turn the adjustment VR so that the voltage becomes
SL VR404 in 2.0 mV ± 0.2 mV.
TP404 pin 3 (–)
TP405 pin 1 (+)
SR VR405 (Condition : No signal and no load) D
TP405 pin 3 (–)
• Adjustment points and measurement points.... see fig.1.

B AMP5 ASSY SL_VR404 C_VR403 SR_VR405 FR_VR402

FL_VR401 FL_TP401 SL_TP404 C_TP403 SR_TP405 FR_TP402

Fig.1 SIDE A
VSX-522-K 57
5 6 7 8
 1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
A
- The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
- Screws adjacent to b mark on product are used for disassembly.

- For the applying amount of lubricants or glue, follow the instructions in this manual.

(In the case of no amount instructions, apply as you think it appropriate.)

9.1 PACKING SECTION

Poly bag packing style
Tape (clear)

Cord AC

Safety Brochure

Sheet SP caution
Dry cell batteries (AAA size IEC R03)

1/2

Label getter “L”

D

Label getter “R”

2/2

58 VSX-522-K
1 2 3 4
 5 6 7 8

PACKING SECTION PARTS LIST

Mark No. Description Part No.
1 Remote Control (AXD7660) 8300766000010-IL
2 AM Loop Antenna E601019000010-IL A

3 FM Wire Antenna E605010140010-IL

4 Microphone APM7010
(for Auto MCACC setup)

5 Quick Start Guide 5707000006490-IL

6 Operating Instructions 6517000000500-IL
(CD-ROM)
7 Box, Gift 522CU 6007212070000-IL
8 Cushion, Snow VSX-522 6230213144000-IL

B
9 PE, Sheet 6327040059000-IL
NSP 10 Warranty Card ARY7156
NSP 11 Label VRW1629

VSX-522-K 59
5 6 7 8
 1 2 3 4

9.2 EXTERIOR SECTION

C
F

O
Clamp

E Nut

Nut

F
P
R

60 VSX-522-K
1 2 3 4
 5 6 7 8

Stopper

Sheet speaker

S ×24
D

C
A
J
Main chassis

K
H
D

G
Silicon adhesive
(GYA1011)

C
Clamp

I
B
NON-CONTACT

CONTACT SIDE

Silicon grease
SIDE

Heatsink
(GEM1057)

VSX-522-K 61
5 6 7 8
 1 2 3 4

EXTERIOR SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 AUDIO Assy 7028071641060-IL 46 Screw BBT40P080FTB

A 2 AMP5 Assy 7028070243010-IL 47 Screw BBZ30P080FTB
3 MAIN Assy 7028071611060-IL 48 Screw BBZ30P080FTC
4 D-MAIN Assy 7028071651010-IL 49 Screw BBZ30P180FTC
5 VIDEO Assy 7028071631010-IL 50 Screw BSZ30P040FTB

6 G-L Assy 7028071615060-IL 51 Screw Tapping Assy B018230141H11-IL

7 G-R Assy 7028071614060-IL 52 Screw, Tap Tite B020230063B10-IL
8 WG-B Assy 7028071617060-IL 53 Screw 1500001206010-IL
9 WG-A Assy 7028071616060-IL 54 Screw B028940101B11-IL
10 BRG-A Assy 7028071633010-IL 55 Screw 1500001456010-IL

B
11 BRG-B Assy 7028071634010-IL
12 BRG-C Assy 7028071635010-IL
13 FRONT Assy 7028071621060-IL
14 INSEL Assy 7028071623060-IL
15 HP Assy 7028071622060-IL

16 MIC Assy 7028071624060-IL

17 F-USB Assy 7028071625060-IL
18 WG Assy 7028071627060-IL
19 STBY Assy 7028071632010-IL
C
> 20 Cord Assy L068125101710-IL

> 21 Power Trans 522CU 8200960611230-IL

22 Cable Flat Card 1.0 N711231712480-IL
> 23 Transistor J5011560Y0000-IL
> 24 Semi, TR/GE NPN 2SC J502396400010-IL
> 25 Transistor J5032390Y0000-IL

26 Pioneer Badge B (PLS) XAM3006

27 Sheet 1210210235000-IL
28 Cabinet VSX-522 3007212006000-IL
D 29 Front Panel 522CU 3067215481000-IL
30 Back Chassis 522CU 3207214176000S-IL

31 Foot (PLS) 4000210391000-IL

32 Bracket 4010056906010-IL
33 Cushion 4050211605000-IL
34 Screw Cover 4050211745100-IL
35 Support 4070001601010-IL

36 USB Mic Plate 522 4470212416000-IL

37 Window 522CU Upper 5077213113080-IL
E 38 Window 522CU Lower 5077213123300-IL
39 Knob 5080212431000-IL
40 Button 5090213741100-IL

41 5 Key Button 5090214561000-IL

42 10 Key Button 5090214571000-IL
43 • • • • •
44 • • • • •
45 Screw BBT30P100FTB

62 VSX-522-K
1 2 3 4
5 6 7 8

VSX-522-K 63
5 6 7 8
 1 2 3 4

10. SCHEMATIC DIAGRAM

10.1 AUDIO ASSY
A R598
0

R601
0 (SBL)
(SW

R509

R516
0

0
JACK402 C400
R400 (SBL) C490 R402 10/50 (SBL)

(SBL)
100 - 2K
Q401 R408
100P-J 100P-J
C402

R405

R406
C403

47K

(FL)

(SW)

(SL)
INC2001AC1

(C)
-
-

10K

R413
C404

C405

Q404 10K
R411
R416
47K
-

INC2001AC1 -
R417 C487 R419

47N-K

47N-K

47N-K

47N-K

47N-K

47N-K

47N-K

47N-K
C411

C412

C413

C414

C415

C416

C417

C418
100 - 2K C408
10/50

R422
4K7
R470

22N(EB)-100V

47N(EB)-100V
0
JACK403 R462 C460
R466

C424
C423
1K 10/50
R461 C470 - 1K
B 100
R468 R463 (SW)
R467

R465
100P-J
C465

47K
C457

150N(R)-63V
-

100/16

100/16

100/16
100/16
10K 10K

100/16
R459

C430
10/50

10/50
C434
C433
10/50
C429
C425

C427

C428

C431

C432
C476

0
C469
0
-

C472

R479
-2012
C459 C441

100P-J
Q416 - Q417 10N-K-2012

C479
J500 0 C468 10N-K-2012
INC2001AC1 INC2001AC1
J501 0 47/10
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
J502 0 R447

100P-J
C467 4K7 C447

R520
R517
150N(R)-63V

C482

470
31

470
47/10
C466 32 99
R473

10N-K-2012
C448 47N(EB)-100V
0

33 98
C449 22N(EB)-100V
34 97
35 96
(SBL) 36 95
37 94
(C) 38 93
(SW) 39 92
(SL) IC400
40 91
R2A15218FP
41 90
R472 100 C462 10/50 (FL) 42 89
R469 100 C464 10/50
43 88
470K
470K
44 87
45 86
46 85
R477
R478

47 84
C R491
R481
47K

C488 48 83
10/50 0
49 82
50 81

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
C489
R485
47K

C473
10/50 10N-K-2012 C477
100P-J
0

(CD) C480
JACK401

(TU)

(CD)
R521 100P-J
R505
C492 10/50

10K
R511 470
R512 470

330
470K
100P-J 100P-J
C493

R523
R522
220P-J 220P-J
C494

R503
-
C496

C497

470K
R527

R528
-

R530 10/50
C498
330
R532 C499 10/50
330
220P-J
100P-J

R534
470K
R533
C501

C502

(SW)
220P-J
100P-J
C504

C505

R537

R538
470K
-

D R541 C506 10/50

330

R593 C542 10/50 C508 10N-K

R542 (SW)
330 C509 10/50
220P-J
100P-J 100P-J

470K
R594
C543

R595
C544

0
-

C503
IC401
220P-J

AZ4580
C539

C475 R497
C540

R592

R539 R540
R591
470K

C507 4 3 5
-

R544 R500
680P-J

4K7 4K7 10/50 1K

R590 1 7
C541 10/50 1K 10/50 0
1N-K

6 8
47K

2
330
R548 R507 1K5
R551
100K
C511

5K6 C484
3N3-K

R554
1K5
R549

3K9
C512

100K

47P-J
R513
C481

LUG401
NM C514
C515
C486 R515

10N-K-2012
10N-K-2012
R557 91K
R518

IC402
10N-K

AZ4580
10/50
C485

: Audio Signal Route (L ch) IC403

R561
8 6
R559 10K
(FL) AZ4580 R560 10K
8 6 7 D414
10K R562 -
: Audio Signal Route (Front L ch) 7 5 LBAS16HT1G
2K2

C516 1/50
(SL) C519
5 C517 -
: Audio Signal Route (Surround L ch) - R566 10K Q425 R565 470K
R568
R564

(C) 10K 2SK492C

C520 - Q426

E : Audio Signal Route (Center ch) C522 - R569 10K

RT1P141C
R571 91K
(SW) R572 10K
R573 10K
2
: Audio Signal Route (SubWoofer ch) (FL) 2
R576
1
R574 10K
RT1N441C

(SBL) 1
10K
4 3 R577 -
D415
Q427

: Audio Signal Route (Surround Back L ch) 4 3

R613 10K

(TU) LBAS16HT1G
(FL)

Q428
(SW)

: Audio Signal Route (Tuner L ch) C529 2SK492C

(CD) C528
10N-K-2012 10N-K-2012
: Audio Signal Route (CD L ch)
(HP)
: Audio Signal Route (Headphone L ch)

R582 470K
R583 470K
R609 470K
C558 C566
R610 470K
- -
10N-K
C534

C546 C547

330P-J 330P-J
(TU)

ZD401
10N-K

ZD400
C533

R588 MTZ6.8B MTZ6.8B R589

100(1) 100(1)
C537
F 220/16(6.3*11) C538
220/16(6.3*11)

A C CP17

64 VSX-522-K
1 2 3 4
 5 6 7 8

A
A AUDIO ASSY
(SW)
(7028071641060-IL)
***************************************
ALL DESTINATION:100pF/50V CH
***************************************
(FL) C401 Q402 (FL) C407,C409,C419,C426,C435
R404 INC2001AC1
SYXCN5
100pF/50V CH
(SBL)

(HP)
10/50 1K5 R409 JXCN

R410
OTHER 100pF/50V CH

47K
10K

C559

-
(SL) C406 R415
Q405 CN400
INC2001AC1 2.0MM-13P
10/50 1K5 R420 C407 100P-J

R421
47N-K

47N-K

47N-K

47K
(SL)
C416

C417

C418

13 12 11 10 9 8 7 6 5 4 3 2 1
10K
C409 100P-J

C560

-
C419 100P-J
(C) C420 R427 Q406 INC2001AC1
10/50 1K5 (C) C426 100P-J
R428

B 1/2 CP401

R429
47K
10K C435 100P-J B

C561

-
100/16

10/50
C434
C433
10/50
C432

C439 R433
Q407 INC2001AC1
10/50 1K5 R435 (SBL)

R436

47K
10K

C562

-
8 7 6 5 4 3 2 1

C446 Q410
R444 INC2001AC1
99 1K5
10/50 R448

R449
47K
98
97 10K

C563

-
96
95 (SBL) C454 R458
Q413
94 INC2001AC1
10/50 1K5 R460
93

R464

100P-J
C438
47K
92 10K

C564
91

-
90
C463 R471
89 Q418 INC2001AC1
88 10/50 1K5 R474

R484

100P-J
47K

C442
87
10K

R602
86

C565

-
0
85
84
83 C
82 (HP)
81
(SW)

73 74 75 76 77 78 79 80
(SW) (SW)

R501 470K
R502

C478 0.22U/25V
(CD)

R508
Q419 470
RT1P141C R514
10K

R495 0 R499 0

C422 R487 C444 R586 C440 R510

5 470/16 33(1)

82P-J
220

C551
1/50 1K 1/50 7
2SK492C

Q414
(HP)

220P-J
6 8

220K
INC2001AC1
Q433

INC2001AC1
4K7
220K

R424
LBAS16HT1G

R423 R492 22K 10K

Q420
D416

10K

R401

R498
C554

C410

C556
R475

R493
5K6
C553
D
-

-
R531 470K 100P-J C568
C500 0.22U/25V 220P-J 10N-K-2012
R535
220K
C555

C557
LBAS16HT1G

R490
(SW) C552

INC2001AC1
Q421 470 5K6
-

-
4K7
100P-J
220K

RT1P141C R536 10K

R414 R425
D417

Q422
R597 470K 10K 10K
C421
INC2001AC1

R403

R489
Q415

22K

R506
(SW) C545
R476

100N-K
2SK492C

R599 R587
2
Q435

100 33(1)
82P-J
C550

R500 Q429 C443

RT1P141C R600 10K C436 R488 1/50 R596 1
0 3 4 C437
1K 470/16 (HP)
1/50 220
1K5 R496 C569
0 R504 IC406
AZ4580 10N-K-2012
C484 0
47P-J
R529

R543
0

(HP)

(SBL)
1
2

C518 1/50
3

R567 470K
4
R570

E
2K2

(SW)
5

Q432
RT1P141C
6

CP403

(C)
7
8

(SL)
9
RT1N441C

10
Q434

11
R614
10K

12

(FL)
13

J
14
15
16

J402 NM
17

J416 0
18
(HP)

J415 0
19

CN403
C125Z2-19
C571 CH10P-D
C549 CH10P-D
C548 CH10P-D
C570 CH10P-D

- When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
C535
10N-K - The > mark found on some component parts indicates the importance of the safety factor of the part.
C536 Therefore, when replacing, be sure to use parts of identical designation. F
10N-K
- : The power supply is shown with the marked box.
CN402
C125Z2-17

K CP402 A
VSX-522-K 65
5 6 7 8
 1 2 3 4

10.2 AMP5 ASSY (1/2)

A
B 1/2 AMP5 ASSY (7028070243010-IL)
(FL)

(FL)

(FL)
CN400

(SL)

(C)
A

(C)

(C)
(C)

E
(SL)

C534,C552 C523,C549,C524,C555 C441,C457,C473

C536,C558 C529,C550,C532,C557 C489,C505

ALL 100P/100V 100P/100V 100P/50V

F B 2/2

B 1/2
66 VSX-522-K
1 2 3 4
 5 6 7 8

(FL)
: Audio Signal Route (Front L ch)
(SL)
: Audio Signal Route (Surround L ch)
(C)
: Audio Signal Route (Center ch)

(FL) (FL)

CN1
(FL)

(C) B
(SL)

C
CN3
C
C

(SL)

D 4/4 CP2005
(C)

(C) (C)

E
(SL)

F
B 2/2
B 1/2
VSX-522-K 67
5 6 7 8
 1 2 3 4

10.3 AMP5 ASSY (2/2)

A
B 2/2 AMP5 ASSY (7028070243010-IL)

B 1/2
(SL)

(SL)

E C539,C553,C542,C563
C544,C554,C547,C564

ALL 100P/100V

B 2/2
68 VSX-522-K
1 2 3 4
 5 6 7 8

A
(SL)
: Audio Signal Route (Surround L ch)

B 1/2

(SL)
(SL) (SL)

B 2/2
VSX-522-K 69
5 6 7 8
 F
E
B
A

D
C
FROM MAIN TRANS

70
C
CP1
35328-0360
1 2 3 5 4 3 2 1 1 2 3

CP3
35328-0360
CP2

1
1

5267-03A
C5 C6

GND2
NM 10N(EB)-100V
R640 0 C2 C3
R641 0 NM 10N(EB)-100V
C7 C8
NM 10N(EB)-100V

C13 C14

C64
100N(EB)-100V

R42
R41
R25 C61

0R22(1)
NM

0R22(1)
10N(EB)-100V
100N(EB)-100V C10 C11

C81
R31
10(1) NM 10N(EB)-100V

47N(EB)-100V
R27 L1
C18 C19
0R22(1) C65 SP-2507 (C) NM 10N(EB)-100V
100N(R)-250V C15 C16
C1 NM 10N(EB)-100V

C83
C82
- - -
10.4 MAIN ASSY

-
-
47N(EB)-100V

C75
C79
R5

R32
C70 C69 R26

0R22(1)
10(1) R6

D7
10(2)

47N(EB)-100V
R79 1M-3216 L2

47N(EB)-100V
GBJ1006
R48 1M-3216 SP-2507 (FL) (FL)

C78
C68
C67
C4

C66 100N(R)-250V
C71 -
47N(EB)-100V RLY2
C78 0.1uF R7
C72 100N-K HL3-2A-12S

X7R
10(1) R8

LOW
0.1uF
(FL)

100N(R)-250V
TO CHASSIS
10(2)

100N(R)-250V
R36 R35 L3

D10
47K(1/4) SP-2507

D12
D11
47K(1/4)

D13
1N4007

1N4007
1N4007
(C)

1N4007
C9 (C)

D9
C58 C55
6800/63(30*40) 6800/63(30*40) R9 47N(EB)-100V

D4912
C73
6800/16(16*31.5)
10(1) R10

2
2

C76
RLY3
10(2) HL3-2A-12S

KBPC604-6A
KBPC604-6A
L4
SP-2507
C74
(SL)

6800/16(16*31.5)
C77
10N-K C12

10N-K
R11 47N(EB)-100V

2
C MAIN ASSY (7028071611060-IL)

10(1) R12

3
10(2)
L5

4
SPEAKER TERMINAL

B 1/2
SP-2507

C84
4700/25(16*31.5)
(SL) (SL)

5
RLY4

CP402
C17 HL3-2A-12S
CN1 47N(EB)-100V
R13

C85
10(1)
R14
10(2)
L6
SP-2507 (SBL)

1000/25(10*20)
C22 (SBL) (SBL)

2
47N(EB)-100V
C87 R15 RLY5

IC1
IC5
10N-K

VSX-522-K
10(1) R16 HL3-2A-12S

D14
D18

D15
R47

C86

C106
10N-K
10(2)
CN2 L7
SP-2507
NM

-
-

IC2
C23

-
-
KIA7912PI
C24

C107
KIA7812API
KIA7812API

TO CHASSIS

TO CHASSIS
10N(EB)-100V

D25 C25

330(2)
D28 (SBL)

1
D27 47N(EB)-100V
R17

2
RB551V-30 RB551V-30 10(1)

IC3
RB551V-30 RLY6

D16
C96 R18
C94 HL3-2A-12S
10N-K 10(2)

4
10N-K C93 10N-K
C92

3
3

-
C89 C88

KIA7805API
TO CHASSIS
100/16(6.3*11) 100/16(6.3*11)
NM

6
100/16(6.3*11)
C20

D26
C21

(SBL)
C26
C27
C28
C29
C30
C31
C32
C33
C34

7
R75 R71 C105
RB551V-30 OPEN

8
6K8-3216 1M-3216 C108 10N-K
10N-K
10N(EB)-100V
1N-K
1N-K
1N-K
1N-K
1N-K
1N-K
1N-K

C95
1N-K
1N-K

10N-K

9 10

B 1/2 CP403
C90
100/6.3(6.3*5)
CN3
R72
1M-3216

4
4

C53 100/25(6.3*11)
R30
2K2(1)
10

D6
R24

R73
KDS4148U
R29

R74
2K2(1)

NM(3216)
CN5

NM(3216)
2.5mm 4P
Q6

13 11 9 7 5 3 1
Q13

4
R28
CP605

12 10 8 6 4 2
2K2(1)
C125Z1-13

3
RT1P237C

10N-K
MTZ3.3B

C112
RT1N237C

2
10K
R37

DZ1
1
D 2/4 CP2004

D5
10
R23

KDS4148U
C57
10/50
R

S
922L/4
827/8

CUX/F
RT

CN6
 5 6 7 8

CP8 CP14
C125Z1-09 C125Z1-09

1022/42/822:CPU B'D
(Cr)

1
A

522:BRIDGE3 B'D
2

2
-

-
-
-
(Cb)

VIDEO B'D

3
R44

4
R43
C62
C60
(Y)

5
6

6
7

7
8

8
(TU)

9
15

R46 -

R56 -
R55 -
14

(TU)
13
CP9

12

CN401
C125Z1-11

11

1022/42/822:11P
CP16

1
10
C125Z1-11

2
9

1
8

CN16
4

2
7

1022/42/822:11P

3
CN9
6

A
CP605

4
5
C125Z1-13

5
4

6
1

7
2

L
E
2

10

8
3

11

9
4

C125Z1-15

10
5

CP17

11
6
7
8
9

/RST

1
C608 C610 C611
10

/SEN
2 NM NM NM R82 0-1608
11

3
SCLK
R83 0-1608 BEAD601
12

SDIO
4

BD3580
13

(TU)

VCC_5V

C635

C636

R635
R636
C613

NM

NM

NM

NM

NM
R638
6

GND R637
C607 10N-K NM-1608 NM-1608
7

TU_R
R608R 1K C609L 10/50(5*7) CN12
8

TU_L
R608L 1K C609
9

5 4 3 2 1
INT 10N-K 0-1608
C612 C611L R84
PACK601 100N-K 4N7-K
C611R

10/50(5*7)
C609R
4N7-K
C614 NM

(TU)
J7
-

C
C125Z1-11
CP15
J13
0

1
2

CN11
3
4
5
6
7

L
8
R24 Q6 R23 Q5 R22 Q4 R21 Q3 R20 Q2

9
10 RT1P237C 10 RT1P237C 10 RT1P237C 10 RT1P237C 10 RT1P237C

10
Q13 Q12 Q11 Q10 Q9
RT1N237C RT1N237C RT1N237C RT1N237C RT1N237C

11
KDS4148U

KDS4148U
KDS4148U

KDS4148U

KDS4148U
D6

D5

D4

D3

D2

R37 R38 R39 R40 R45 C125Z1-7

10K 10K 10K 10K 10K CP13

CN13
1
2
3
4
D

5
1N4007 22(1/4) Q17

L
R29 R28 D8 D23 R64
C57 R66 KSA916Y
1SS133T

7
2K2(1) 2K2(1) 10/50
4R7(1)
R65
10K
330/63(12.5*20)

C103
1/50
MTZ3.3B

10N-K
DZ1

C59

MTZ16B
C101

Z24
C102

MTZ16B
1/50

Z25

2/4 CP2004 R49 R51

10N-K
C100
100K
R54

51K 51K R52

100/10 KTC3198Y

R50 2K2
2.5mm 4P

Q14
5267-04A
CN5

CN6

4 3 2 1 1 2 3 4
51K
KSA992F
Q16
2N2-K

R73
KTC3198Y
33K

NM(3216)
OPEN
R62

R59

10K

Q15

C112 C113
10N-K 4N7-K
C99
C98
R53
OPEN

OPEN
R63

R58

27K
R61

R60

27K

R74
NM(3216) E

: Video Signal Route

(Y)
: Video Signal Route (Y)
(Cb)
: Video Signal Route (Cb)
(Cr)
: Video Signal Route (Cr)
(FL)
: Audio Signal Route (Front L ch)
(SL)
: Audio Signal Route (Surround L ch)
(C)
: Audio Signal Route (Center ch)
R75 R48/R71
(3216) (3216)
R72/R79
(3216)
(SBL)
827/822/522 6K8 1M 1M : Audio Signal Route (Surround Back L ch)
SYX/JX
922L/42/822/522
(TU) F
OPEN OPEN OPEN
CUX/FLX/PWX/AX : Audio Signal Route (Tuner L ch)

C
VSX-522-K 71
5 6 7 8
 F
E
B
A

D
C

72
D 1/4
1
1

JACK2003 AD3PBI19GO-REV.B JACK2002 AD3PBI19GO-REV.B JACK2001 AD3PBI19GO-REV.B JACK2000 AD3PBI19GO-REV.B

21
21
21
21
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

22
22
22
22
R2003 R2002 R2001 R2000

0 0 0 0
- Q2003 R2007 D2002 - Q2002 - Q2001 R2005 - R2004
D2003 RT1N141C RT1N141C R2006 D2001 RT1N141C D2000 Q2000

D2007 - 1K D2006 - 1K D2005 - 1K D2004 - RT1N141C 1K

D2011 - Q2007 D2010 - Q2006 D2009 - Q2005 D2008 - Q2004

RT1N441C R2011 RT1N441C R2010 RT1N441C R2009 RT1N441C R2008
D2015 - D2014 - D2013 - D2012 -
10K 10K 10K 10K
D2019 - D2018 - D2017 - D2016 -
-

-
-
R2019
R2017

D2023 - D2022 - D2021 - D2020 -

R2021

R2023
D2027 - D2026 - D2025 - D2024 -

-
-

5K6
5K6

5K6
5K6
R2013
R2012

-
R2018
R2016

R2015
R2014
D2031 - D2030 - D2029 - D2028 -

R2020

R2022
D2035 - D2034 - D2033 - D2032 -

D2039 - D2038 - D2037 - D2036 -

-
10.5 D-MAIN ASSY (1/4)

-
R2024

R2025

-
R2026

2
2

R2027
R2031 R2030 R2029
47K 47K 47K R2028 47K
R2032 10K
R2035 R2034 R2033
10K 10K 10K

VSX-522-K
3
3

D 4/4
R2036
10K

ZD2003
-
1N-K
C2008
C2007
C2104

C2003
C2006

C2113
C2112

C2330
C2002
C2275
C2261

C2001
C2000

C2329

C2004
100N-K
100N-K

C2005

C2009 100N-K
ZD2004
- C2010 47/16-Z8156
-

-
1N-K
1N-K

1N-K
100P-J
100N-K
100N-K
100N-K

R2037
100P-J

R2038
100N-K
100N-K
100N-K

100N-K

ZD2005 C2011 100N-K

C2156 - C2012
4N7-K 47/16-Z8156
1N-K
C2105

R2039 2K
C2345 R2040
4N7-K 2K
CB2001
CB2000

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2
470

D 4/4
1
R2041

C2346 R2475 0
4N7-K 33 NC 128
0
0

R2476 0
AVSS
AVSS
AVSS
AVSS
AVSS
AVSS
PVSS
VDDE

AVDD
AVDD
PVDD
AVDD
AVDD
PVDD

RX21-
RX11-
RX01-
RX20-
RX10-
RX00-

C2013 34
RXC1-

RX21+
RX11+
RX01+
RX20+
RX10+
RX00+

NC 127
RXCO-

RXC1+
RXCO+

100N-K R2477 0 C2014

AVDD33
AVDD33

C2347 EXT_RES

R2042

R2043
35

100
4N7-K C2015 AVSS NC 126 100N-K

R2049
R2044
100N-K 36 PVDD reserved 125

R2048 100
R2046 100
R2045 100
100

R2047 100
AVDD C2343

1K
37 VDDE 124
RXC2- 100P-J

47K
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
R2084 38 RXC2+ VSS 123
- R2050 10

4
C2073
4

P41 39 AVSS SCL 122

P21
P22
P23
P24
P25
P26
P27
P10
P11
P12
P13
P70
P71
P40

TIMI
100N-K R2052 2K R2051 10

TIMO
2
P8(1) P30 40 RX02- SDA 121
C2348
4N7-K P8(0) 3 R2054 R2053 2K
SPI_DO P31 41 RX02+ VDD 120

XTAL2000
10 R2055 4K7
C2019

24MHZ-15pF
R2056
4

SPI_CLK P32 42 AVDD33 VDD 119

R2059
C2331

C2017 C2016
C2018
100P-J

5
100N-K

0 VSS P33 43 AVSS VSS 118 100N-K

22P-J 2K 100N-K
R2057
6

VDD P34 44 RX12- PH2 117

1M
10 R2058 4K7 R2060 2K
7

R2061
C2021
XO P35 45 RX12+ PH1 116
R2119 0
8

XIN VDD 46 AVDD DDCO_SCL 115

1N-K

C2020
C2332

R2120 0
100N-K

IC2001
20P-J

EPF021A
VSS VSSA 47 RX22- DDCO_SDA 114
4N7-K

C2321
100N-K VDD ADC1 48 RX22+ VSS 113
R2062 100
47

C2349
-

ADC0
IC2000

P63 49
R2063

AVSS/PVSS IIS_SDO 112

EP94A1K

4N7-K
C2108 C2109

R2064 100
C2022 C2023
100N-K 100N-K
C2024

VDDA 50
100N-K

P62 PVDD/AVDD IIS_WS 111

C2333 -

R2065 R2066 100

P61 DP 51 RXC3- IIS_SCLK 110
47K R2067 100
P60 DM 52 RXC3+ MCLK 109
R2069 0 RSTb C2025
P07 opm0 100N-K 53 AVSS VSS 108
R2068

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
9 10 11 12 13 14 15 16

P06 54 RX03- VSSE 107 10K

R2071 100

P05

D 4/4
R2070 55 RX03+ SPDIF 106

32
P04 31
P03 30
P02 29
P01 28
P00 27
P57 26
P56 25
P55 24
P54 23
P53 22
P52 21
P51 20
P50 19
RMC 18
GND 17

10K C2026
56
C2

AVDD33
2.2/

C2

100
1N

VDD 105 100N-K

 M
10 R2058 4K7 R2060 2K

061
C2021
XO P35 45 RX12+ PH1 116
R2119 0

8
XIN VDD 46 AVDD DDCO_SCL 115

1N-K

C2020
C2332
R2120 0

100N-K

IC2001
20P-J

EPF021A
VSS VSSA 47 RX22- DDCO_SDA 114

4N7-K
C2321
100N-K VDD ADC1 48 RX22+ VSS 113
R2062 100

47
C2349

-
ADC0

IC2000
P63

R2063
49 AVSS/PVSS IIS_SDO 112

EP94A1K
4N7-K

C2108 C2109
R2064 100

C2022 C2023
100N-K 100N-K
C2024
VDDA

100N-K
P62 50 PVDD/AVDD IIS_WS 111

C2333 -
R2065 R2066 100
P61 DP 51 RXC3- IIS_SCLK 110
47K R2067 100
P60 DM 52 RXC3+ MCLK 109
R2069 0 RSTb C2025
P07 opm0 100N-K 53 AVSS VSS 108
R2068

42 41 40 39 38 37 36 35 34 33
9 10 11 12 13 14 15 16
P06 54 RX03- VSSE 107 10K
R2071 100

P05
P52
P51
P50

D 4/4
R2070 55 RX03+ SPDIF 106

32
P04 31
P03 30
P02 29
P01 28
P00 27
P57 26
P56 25
P55 24
P54 23
P53 22
21
20
19
RMC 18
GND 17
10K C2026
56 AVDD33 VDD 105 100N-K
4 3 2 1 C2028

1N-K
C2027
C2334
57 AVSS

100N-K

10
VDD 104 100N-K

1A
R2072
C2030

2A
3Y
R2073 58 RX13- VSS 103

GND
CB2002 0

-
1K 59 RX13+ VSS_PLL 102 C2342

-
1N-K

IC2002
60 AVDD
2.2/50-Z8154 2K2

47K
C2029 R2074

C2031

R2233
100N-K
PLL_XFC_A 101 C2032

100P-J
C2335

100N-K

R2075
4N7-K

ZD2006
UDZ5.1B

VCC

2Y
3A
1Y
61 RX23- VDD_PLL 100
C2033
5

5
5 6 7 8 62 RX23+ VDDE 99
R2076 C2034
100N-K
63 AVSS XOUT 98

-
0 22P-J

R2079
64 SWING XIN 97

DDC3_SDA
DDC2_SDA
DDC1_SDA
EXT_RSTb

DDC3_SCL
DDC2_SCL
DDC1_SCL
IIS_SD3
IIS_SD2
IIS_SD1

AVDD18
AVDD18
AVDD33
A_MUTE

DSD3L
DSD3R

TX0-
TX1-
TX2-
AVSS
VSSE
INTb

VDD

TX0+
TX1+
TX2+
NC

TXC-
VSS

PVDD18
TXC+
AVSS
1M
R2078

1N-K
C2341

65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

-
C2036
XTAL2001

C2035
18M432MHZ-15pF

270
20P

R2080
82P-J
C2202

C2205
82P-J
-
C2353
R2083
R2081
R2082

D 2/4
C2039
100N-K CB2003

R2077
C2038

R2457
C2336 0

C2338
1N-K
47/16-Z8156 82P-J
C2040

C2041

C2045

IC2003
100N-K
100
100

100
1/50-Z8155

100N-K

EPF011C
R2471 0
R2309 0
R2290 0
R2234 0
R2226 0
R2135 0

47
C2037
C2043

100N-K
C2044

C2047
C2337
C2046

100P-J
C2042

100N-K
100N-K
10/16-Z8154
100N-K 1/50-Z8155
BIST RXD

C2340 82P-J

1N-K
A6 TXD
0

C2339

CB2006
CECOCECin
CB2004

CB2005

4R7
C2048 DDC_SCL

CB2010

0
1000N-K VSS
DDC_SDA R2085
VDD 10
XO SCL

27K
C2049

R2086
XIN SDA 100N-K
C2206 4N7-K C2050
C2052 10N-K R2087 C2054 10/16-Z8154
C2053 100N-K
VSS RSTb 10
OP_MODE 100N-K
C2055 100/6.3-Z8156 C2051 C2056
VDD 1N-K 100N-K
A2 IO3 C2058
C2057 47/16-Z8156
A1 IO2 10/16-Z8154
C2208 4N7-K

3
4
A0 INTb

24 23 22 21 20 19 18 17 16 15 14 13
1 2 3 4 5 6 7 8 9 10 11 12
NC VO
CB2007
CB2008
6

6
2
10K
10K
10K
GND

R2089
R2088
CB2009

R2090

IC2004
0
R2091

D2044

NJM2831F33

1
5

D 4/4
CNT VI
47K

LBAS16HT1G
R2092
0
0

10 C2060 10N-K
C2059 1/50-Z8155

CB2014 0 R2188

270

C2061 1N-K
R2093 C2062 10/16-Z8154
10

R2094 VOUT

1
5
ON/OFF
47K

2
C2063 VSS

IC2005
100/6.3-Z8156 C2068

VSX-522-K
3
4

S-1170B18-UC
NC
VIN
-
C2064
C2065 1N-K

D 2/4
100N-K
C2066 10/16-Z8154
0
R2134

C2067
R2096 1000N-K R2095

51 1 4 1 4 1 4 1 4 5 4
7

7
R2098
IN
ON

4R7 R2097 C2069

R2101
R2102

L2003
L2002
L2001
L2000

51 1000N-K
-

2 3 2 3 2 3 2 3
IC2006

-
-

-
0

0
GND
SET

OUT

D2045 CDS2C05HDMI1 R2105 1 2 3

1K8
R2100
0

D2046 CDS2C05HDMI1
R2106
R2104

D2047 CDS2C05HDMI1 - R2099

1K8
D2048 CDS2C05HDMI1
-
D2049 CDS2C05HDMI1 R2103
0
0

D2050 CDS2C05HDMI1
0
CB2011
CB2012

D2051 CDS2C05HDMI1
C2071
D2052 CDS2C05HDMI1 1000N-K
D2053 CDS2C05HDMI1
D2054 CDS2C05HDMI1
C2072
1N-K

R2108 C2070
R2107
- - 0 C2201
82P-J
0
CB2013

22

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
21
8

8
AD3PBI19GO-REV.B JACK2004
+5V
TX0-
TX1-
TX2-

GND
TXC-
TX0+
TX1+
TX2+

TXC+

DDC_SDA
DDC_SCK
TX0 SHIELD
TX1 SHIELD
TX2 SHIELD

TXC SHIELD

CE_REMOTE

HP_DET/HEAC-
UTILITY/HEAC+
D 1/4 D-MAIN ASSY (7028071651010-IL)

73
D 1/4
F
E
B
A

D
C
 F
E
B
A

D
C

74
C CN5

JACK2005
4 3 2 1

RCA-107A

D 2/4
CP2004
5268-04A
JSR1165-C
JACK2006
D2055

L2004
LBAS16HT1G

BD121T

1
1

C2075 R2109
10N-K 4K7
C2074
22P-J C2076

2.2UH
L2005
C2077 330P-J
100P-J R2110
C2079 C2078
47/16-Z8156
100N-K 75
C2081
- C2080
C2082 22P-J

R2111
1N-J
C2083

Min.25V
C2089 330P-J
C2085

0
330P-J 10P-D C2087

10N-K
L2006

C2084
R2316

C2086
C2092 330P-J

100 0.1/50-Z8154
100N-K C2088 -
R2112

-
C2093 100N-K 100K

Q2027
GRM31CB31E106KA75L C2091
C2095

0
GRM31CB31E106KA75L
GRM31CB31E106KA75L C2094

10K

R2458
GRM31CB31E106KA75L

22P-J
C2090

R2113

100N-K
Q2026

C2097
R2114
2K2
IC2008 IC2007
R2116 BD9328 BD9329 C2322
10.6 D-MAIN ASSY (2/4)

R2115

L2035

10P-D
10P-D

C2099
C2096

L2036
0

0
C2098
0 0 100N-K
BST SS BST SS
VIN EN R2118 C2100 VIN EN R2117
C2101
100N-K 11K 100N-K 7K5

1000N-K
47P-J

C2107
C2106

11 12
9 10
11 12
9 10
SW COMP SW COMP

1 2 3 4
100N-K 8 7 6 5
1 2 3 4
8 7 6 5
C2103 C2102

2
2

GND FB CH2N2-J GND FB

3N3-K
R2462
R2125 5K6-F R2126 7K5-F -

-
Q2029

22UH
22UH

L2008
L2007
2K2

R2122
R2121

33
33

0
R2124
R2123
100K

R2136

R2137
R2465

-
R2133 R2132 R2131 R2130 R2129 R2128

10
750 18K-F 7K5-F 330 10K-F 10K-F 7 6 5 4 3 2 1

10
Q2028
3A
1Y
1A

3Y
2Y
2A

C2111 C2110

GND
GRM31CB31C226KE15L GRM31CB31C226KE15L C2323
R2127

C2116 C2115 100N-K

IC2009

GRM31CB31C226KE15L GRM31CB31C226KE15L
74VHCU04

C2118
4Y
4A
5Y
VCC

5A
6Y
6A

R2140 C2117
1N-J 47K 1N-J 8 9 10 11 12 13 14
R2141 C2114
300K

R2139 R2138 47K 330P-J

1M 1M C2119
10N-K

VSX-522-K
C2354
R2463 82P-J
AXCN(CHINA):NM

-
Q2031
100
R2142

C2120 -

0
L2009

R2466
C2121

-
10/16-Z8154 0

D 4/4
Q2030

3
3

C2324
L2010

C2122
BD121T

100N-K
100N-K
33
R2143

R2464

-
Q2033
0
R2467

-
Q2032
C2325
100N-K

D 1/4

4
4

D2057

D2056
RB501V40

RB501V40 C2123 10N-K

CN2003
C2124 CH2N2-J

C125Z2-19
C2125 4N7-K

1
C2350 82P-J

2
3
4
5
6
(FL) (FL)

J
8
9
10
(SL) (SL)
100
100

11
R2144
R2145

CP2
 5 6 7 8

D 2/4 D-MAIN ASSY (7028071651010-IL) A

R2187
L2016
-
L2013
2.2UH

10000N-K

10000N-K
C2135 100/6.3-Z8156 L2015

100N-K
C2148

C2149

C2150
-
C2133 10N-K

C2139

C2141
10N-K
BD121T
C2134
-
C2155
330P-J B

10K
12K-F
R2154

R2156

R2167

330P-J
R2164
L2014

R2162

C2138
10K

100N-K
330P-J
L2011

10K
LBC2012T-4.7UH

0
- 61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
L2012
4N7-K
82P-J

VIN
NC

I2C
CAD0

CAD1

TX0
TX1
RX3
PVSS

RX4

RX5

RX6

RX7

MCLK
PVDD

TEST2

DAUX2
INT1
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

R2185

100/6.3-Z8156
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
LBC2012T-4.7UH RX1 BOUT
10000N-K

R2186
C2129

C2128 NC TVDD
10N-K

C2140
C2144
C2145
C2132
C2125
C2350

100/6.3-Z8156 XTAL2002
RX0 DVDD
AVSS 80.INT0 DVSS

C2146
C2130 24.576M(15p)

C2147
22P-J
22P-J
10N-K AVDD 61.RX2 XTO
VREFH 60.TEST1 XTI
C2126 C2127
R2145 VCOM TEST3
100 - -
C2131 RIN MCKO2
220/6.3-Z8157 IC2011 R2184
LIN MCKO1
R2144 AK4588 47
NC COUT
100 R2146 100
ROUT1 UOUT
NC VOUT
(FL) R2147 100
LOUT1 SDTO2
R2178 33
R2179 33
NC BICK2
R2148 100 19.LRCK1 R2180 33
ROUT2 LRCK2
41.ROUT3(C) 20.CDTO R2181 33
(SL) R2149 100
NC 21.CCLK/SCL SDTO1
R2182 33
C
LOUT2 22.CDTI/SDA BICK1
32 MASTER

R2183 33
37 ROUT4
39 LOUT3

35 LOUT4

24 DAUX1

NC
31 PDN

23 CSN
30 XTL0
29 XTL1
28 SDTI1
27 SDTI2
26 SDTI3
R2168 SDTI4
34 DZF1
33 DZF2

(C) R2150 100

38 NC

36 NC
40 NC

10K 25

22
21
R2158

R2159

R2177
4K7

4K7

(SW) R2151 100 R2171 4K7 C2142

C2136
10N-K
R2155
47K

R2152 R2172 4K7 100P-J

100
C2143
10
10
10
10

R2153 100
R2174

100P-J
R2173
33

33

(SBL)
47

R2161
R2163
R2165
R2166
(SBL)
(SW)

R2157
(SL)
(FL)

(C)

D 3/4

R2175 0

R2176 0

R2169 0
R2170 0

E
16 15 14 13 12 11 10 9
10N-K

VCC

4B
4Y
3A
3B
3Y
OE
4A

*HD_AUDIO/DSD SELECT
(SBL)
(SW)

IC2010
(SL)
(FL)

(C)

TC74VHC157FK L HD_AUDIO
GND
C2137

A/B
1A
1B
1Y
2A
2B
2Y

H DSD
1 2 3 4 5 6 7 8
R2160

47K

: Audio Signal Route (L ch)

(FL)
: Audio Signal Route (Front L ch)
(SL)
: Audio Signal Route (Surround L ch)
(C)
: Audio Signal Route (Center ch)
(SW)
2 4 6 8 10 12 14 16 18 : Audio Signal Route (SubWoofer ch)
1 3 5 7 9 11 13 15 17 19 (SBL)
: Audio Signal Route (Surround Back L ch)
J CP2003 F

D 1/4
D 2/4
VSX-522-K 75
5 6 7 8
 1 2 3 4

10.7 D-MAIN ASSY (3/4)

A
D 3/4 D-MAIN ASSY (7028071651010-IL)

L2017 0 CP2007 -

1 2
R2239
-

100/6.3-Z8156
R2240
-

100N-K
D2058 -

C2171

C2176

C2181
1N-K
IC2013 L2025

-
-
SA1117D-1.2 0

10N-K

C2163

C2167

R2244
R2247
1N-K
220/6.3-Z8157
10/16-Z8154

-
L2026

C2153
0

10N-K
C2152

C2154
C2151

C2164

C2168
1N-K
-
R2468
B -

100N-K
C2172

C2182
C2177

1N-K
L2018 100/6.3-Z8156

-
100N-K

10N-K
BKP_HS101-2125
R2379

47K

R2209 47
R2210 47

100N-K
C2203

C2210
C2326
C2157

C2158
R2211 47
Q2034
FDC608PZ -
D2065
Q2035 L2021 C2173
RT1N141C BKP_HS101-2125 100/6.3-Z8156
132131130129128127126125124123122121
IC2015

100N-K

AXR0[11]
AMUTE1
AFSR0

AXR0[8]
UART1_RXD
USB_REFCLKIN

UART1_TXD
Dvdd

ACLKX0
AFSX0
ACLKR0
AHCLKR0
C2178

C2183
IL1117-1.8

C2169

1N-K
133

1N-K
C2165 C2200
10000N-K 134
L2022 C2174 135
100/6.3-Z8156 220N-K USB0_VDDA18
BKP_HS101-2125 136 NC

100N-K
C2184
137 USB0_DP

C2179

1N-K
L2023 138 USB0_DM 133:RSV2
0 139 NC 134:USB0_VDDA12
140 USB0_VDDA33

100N-K
C2166

C2180
L2024 141 PLL0_VDDA

-
0 C2185
142 PLL0_VSSA
R2205 1M C2175 10P-D
143 OSCIN
10000N-K

R2204
144 OSCVSS
XTAL2004 -

0
R2208 C2187
145 OSCOUT
100N-K
146 RESET
C 147 CVdd

C2162
18P-J

C2170
148 RTC_XI

18P-J
24M(12P) C2188
1N-K 149 RTC_CVdd
C2189
100N-K 150 TRST
151 DVdd
R2206 470
152 TMS
C2186 330P-J C2190
R2207 47K 153 TDI
100N-K
C2191 154 CVdd
330P-J
155 TCK
R2223
156 TDO
47 C2192
100N-K 157 GP7[14]
158 DVdd

D 2/4 R2212 C2193

BD121T

159 CVdd
100/6.3-Z8156

L2020

47 100N-K
160 AHCLKX1
220N-K
C2161
C2160

C2194
C2159
10N-K

R2190 R2213 100N-K 161 CVdd

47K 47 C2195
1N-K 162 ACLKX1
R2203

IC2014 163 AFSX1

74LCX257MTCX R2214 C2196
47 100N-K 164 DVdd
0

A/B 165 ACLKR1

9 10 11 12 13 14 15 16

VCC
8 7 6 5 4 3 2 1

R2191 0 1A C2197
OE 166 AFSR1
R2192 47 R2483 0 100N-K
1B 4A C2198 167 CVdd
R2193 100 R2196 0 R2215 47 330P-J
1Y 4B 168 AXR1[8]

2:I2C0_SDA
3:I2C0_SCL
R2227 0 2A R2199 33 R2216 47
4Y 169 AXR1[7]

1:AXR1[0]
R2482 0 R2197 0 R2217 47
2B 3A 170 AXR1[6]
R2194 100 R2198 0 R2218
D 2Y 3B
R2200 100
47
C2199
171 AXR1[5]
GND 3Y 172 DVdd
100N-K
173 AXR1[4]

SPI1_SCS[0]
SPI0_SCS[0]
R2219 100

SPI1_ENA

SPI0_ENA
SPI0_CLK
174 AXR1[3]

AXR1[10]

AXR1[11]
R2220 100 175 AXR1[2]

CVdd
Dvdd
R2221 100 176 AXR1[1]

1 2 3 4 5 6 7 8 9 10 11 12

R2222

100N-K

C2209
100N-K

C2207
C2204

1N-K
100

47

47
47
47
47

47
R2236
R2229
R2231
R2232

R2235

1K5
R2479
4K7
R2237

D 3/4 D 4/4 D 4/4

76 VSX-522-K
1 2 3 4
 5 6 7 8

R2304
-
R2306
0

L2030 D2066

1 4
2 3
R2307 -
A

20010WS-05
DLP11SN121SL2L 0

CP2006

CN2006
R2305 - R2310
L2031 0

1
0

CDS2C05HDMI1
CDS2C05HDMI1

2
3
C2327 -

100N-K

4
C2328 GND FAULT

8
-

-
-
1000N-K

5
IN OUT

-
CP2007 - R2311
IN OUT

6
R2469 R2470 47K

C2351

C2352
0

Q
1 2 EN LIM

C2272
C2273

C2274
4

R2302
R2303
D2267
D2268
R2239
100
-

R2481 R2480
47K-F 47K-F
C2344
IC2024

1N-K
R2240 TPS2557
-
-
-
R2244
R2247

L2028
0
L2029
47

47
47
47
47

47
47
47
47

47
47
47
47
47

47
47

0
C2258
R2254 B
R2255
R2256
R2257

R2258
R2259
R2260
R2261
R2262

330P-J R2263
R2264
R2250
R2251
R2252
R2253
R2249

220/6.3-Z8157
C2250 C2265
100N-K -

C2227
C2251 VDD GND

28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
100P-J
DQ0 DQ15
C2252 1N-K
100N-K
100N-K

100N-K

100N-K

100N-K

100N-K

100N-K
C2228
100N-K

VDDQ
C2212

C2221
C2203

C2216

C2223
C2210

C2213

C2219

C2226
GNDQ
1N-K
1N-K

C2253 DQ1 DQ14 C2266

10P-D
R2287 C2248
DQ2 DQ13 100N-K
100N-K
GNDQ C2267
VDDQ 1N-K
DQ3 DQ12

0
132131130129128127126125124123122121120119118117116115114113112111110109108107106105104103102101100 99 98 97 96 95 94 93 92 91 90 89 C2230 DQ4 DQ11

Dvdd
AXR0[11]
AMUTE1
AFSR0

EMB_A[10]

EMB_A[11]
AXR0[8]
AXR0[7]

AXR0[6]
AXR0[5]
AXR0[4]
AXR0[3]

AXR0[2]
AXR0[1]
AXR0[0]
UART1_RXD

EMB_RAS

EMB_A[1]
EMB_A[2]
EMB_A[3]

EMB_A[4]
EMB_A[5]
EMB_A[6]

EMB_A[8]

EMB_A[9]
EMB_CS[0]
USB_REFCLKIN

UART1_TXD
Dvdd

ACLKX0

EMB_BA[0]
EMB_BA[1]
AFSX0
ACLKR0

EMB_A[0]

EMB_A[7]
AHCLKR0

C2254

EMB_A[12]
CVdd 100N-K
Dvdd

R2265 47
CVdd

CVdd

VDDQ
Dvdd

Dvdd

3 88 1N-K VSSQ
DQ5 DQ10 C2264
4 87
R2266 47 100N-K
5 86 DQ6 DQ9
USB0_VDDA18 R2267 47 C2255 GNDQ C2268
6 NC 85 100N-K VDDQ 1N-K
7 USB0_DP EMB_D[8] 84 R2268 47 C2256 DQ7
88:EMB_SDCKE DQ8
R2269 47 1N-K
8 USB0_DM 133:RSV2 87:DVdd EMB_D[9] 83 VDD GND
134:USB0_VDDA12 86:EMB_CLK R2270 47
9 NC EMB_D[10] 82 LDQM NC
85:EMB_WE_DQM[1] C2231 100N-K
0 USB0_VDDA33 DVdd 81 WE UDQM
PLL0_VDDA R2271 47 C2257 CAS
EMB_D[11] 80 CLK
PLL0_VSSA C2232 R2272 47 100N-K RAS
EMB_D[12] 79 CKE
1N-K R2273 47 CS
3 OSCIN EMB_D[13] 78
C2233 NC
4 OSCVSS CVdd 77 100N-K BS0 A11
5 OSCOUT EMB_D[14] 76 R2274 47 BS1
C2234 A9
6 RESET DVdd 75 100N-K A10 A8
7 CVdd EMB_D[15] 74 R2275 47 A0 A7
C
8 RTC_XI EMB_D[0] 73 R2276 47 A1 A6
C2235 R2277 47
9 RTC_CVdd EMB_D[1] 72
100N-K
A2 A5
DVdd 71 C2259 A3
0 TRST 100N-K
A4
47
DVdd EMB_D[2] 70 C2236 R2278 VDD GND
IC2016 C2237
TMS CVdd 69 330P-J 100N-K
C2260
D808K013BPTP400 R2279 47
3 TDI EMB_D[3] 68 C2238
1N-K IC2018
4 CVdd CVdd 67 W9864G6JH-6
5 TCK EMB_D[4] 66 100N-K R2280 47
177 C2239
6 TDO GND DVdd 65
100N-K R2281 47
7 GP7[14] EMB_D[5] 64
8 DVdd EMB_D[6] 63 C2240 R2282 47
9 CVdd EMB_D[7] 62 1N-K R2283 47
0 AHCLKX1 CVdd 61
CVdd R2284 47
EMB_WE_DQM[0] 60
ACLKX1 C2241 R2285 47
EMB_WE 59
100N-K
3 AFSX1 DVdd 58 C2242
- R2286 47
4 DVdd EMB_CAS 57
5 ACLKR1 CVdd 56
C2243
6 AFSR1 EMA_WE 55 100N-K
7 CVdd EMA_D[7] 54 C2244
8 AXR1[8] DVdd 53
SPI1_SCS[0] 2:I2C0_SDA
SPI0_SCS[0] 3:I2C0_SCL

9 AXR1[7] 47:DVdd EMA_D[6] 52 100N-K

1:AXR1[0]

0 AXR1[6] 46:EMA_D12] EMA_D[5] 51 C2245 L2032

- R2308
45:EMA_D[1]
AXR1[5] CVdd 50
C2246 0 BD121T D
DVdd EMA_D[4] 49 100N-K IC2019

100N-K
1N-K
SPI1_SOMI[0]
SPI1_SIMO[0]

SPI0_SOMI[0]
SPI0_SIMO[0]
EMA_WAIT[0]

3 AXR1[4] EMA_D[3] 48 W25Q32VSSIG

EMA_CS[3]

EMA_CS[2]

C2247
EMA_BA[0]
EMA_BA[1]
EMA_A[10]

EMA_A[11]
EMA_A[12]

100/6.3-Z8156
SPI1_ENA

SPI0_ENA
SPI0_CLK

SPI1_CLK

EMA_A[0]
EMA_A[1]
EMA_A[2]
EMA_A[3]

EMA_A[4]
EMA_A[5]
EMA_A[6]
EMA_A[7]

EMA_A[8]
EMA_A[9]

4 AXR1[3] 47 100N-K
AXR1[10]

AXR1[11]

EMA_D[0]
EMA_OE

R2293 CS#
4 3 2 1

5 6 7 8

5 AXR1[2] 46 47 VCC
CVdd

CVdd

DVdd

CVdd

DVdd

CVdd
Dvdd

Dvdd

SO/SIO1
DVdd

C2271
6 AXR1[1] 45 HOLD#

C2270
C2269
WP# SCLK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 GND
SI/SIO0
100N-K
100N-K

100N-K

100N-K

100N-K

100N-K
C2209

100N-K

100N-K
C2220
100N-K

C2215
C2217
330P-J
C2207

C2214

C2218

C2222

C2225

C2229

R2298

R2300
C2204

C2224

R2292

R2294
C2211
1N-K

R2296
10K

1K
1K

1K

-
-

-
47

47
47
47
47

47
47

47

47

R2295

R2301
R2299
R2297

47K
-

-
-
R2236
R2229
R2231
R2232

R2235

R2238
R2241

R2243

R2248

R2288 10K E
R2289 10K
10
9
8
7
6
5

1K5 C2249
4

R2479 10N-K
3
4K7

4K7

2
-

1
R2291

CN2000
10K
R2237

R2242

R2245

-
R2246
47K

D 4/4 D 3/4
VSX-522-K 77
5 6 7 8
 1 2 3 4

10.8 D-MAIN ASSY (4/4)

A
D 4/4 D-MAIN ASSY (7028071651010-IL)
D 1/4 D 2/4 D 1/4 D 1/4 D 3/4

R2317 0

R2318 0

R2319 0

10K
10K
R2341
R2342
Q2010
ISA1530AC1

R2325

R2323

R2324

R2330
10K

3K3

10K
0
R2326
10K
Q2011
RT1N144C

20 19 18 17 16

10K
10K
{pin20}
{pin19}
{pin18}
{pin17}
{pin16}
R2321
47
R2493

11 12 13 14 15
1
{pin1} {pin15}
C

R2327
R2331
mode1 R2347

2
mode0
{pin3} R2348

3
SDA
reset R2349

4
SCL

100N-K
R2350
R2320

vcc

10N-K
47K

5
vss

47K
R2346

{pin10}
10K

{pin6}
{pin7}
{pin8}
{pin9}
R2484 R2328
10K R2351
0 R2329
R2343

10
330P-J

6
7
8
9
C2282

C2283
C2284
R2322
14 13 12 11 10 9 8 R2344
IC2021
MFI341S2162
10N-K
C2279
C2278

1N-K

-
-
1 2 3 4 5 6 7

R2337
R2340
IC2020
Q2012
R2315 47K

SN74AHCTO8-EL2
R2313 47K

ISA1530AC1 D2061

R2335
10K
LBAS16HT1G

10/16-Z8154
C2285

R2332
3K3
D

Q2013
0
R2456

RT1N237C

R2461

R234
1K
R2338

100K

R2314 47K
LBAS16HT1G

E
C2277 100N-K
D2059
1K

ZD2001 UDZ3.3B
R2353

C2287
R2312

R2333

2.2/50-Z8154 Q20
1K

R2336 2SC30
4K7
10N-K
10N-K

LBAS16HT1G
4K7

47K
D2060

R2339

C2288
C2286
R2334
C2280

C2276
100P-J
C2281
1N-K

10N-K

18 16 14 12 10 8 6 4 2 26 24 22 20 18 16 14 12 10 8 6 4 2
CN2002 19 17 15 13 11 9 7 5 3 1 CN2001 27 25 23 21 19 17 15 13 11 9 7 5 3 1
C125Z2-19 C125Z2-27

F L CP2002 L CP2001

D 4/4
78 VSX-522-K
1 2 3 4
 10/16-Z8154

0K
0K
R2332
C2286 10N-K R2333 1K

Q2012
10K
3K3
R2334

R2326
4K7 D2059 R2335

ISA1530AC1

Q2013
LBAS16HT1G 10K
D2060

RT1N237C
LBAS16HT1G

C2287
D2061
R2337 -

4K7
2.2/50-Z8154
R2339 47K R2338
R2340 -

LBAS16HT1G
C2288 10N-K 100K R2341 10K

R2344
R2343
R2351
R2346
R2350
R2349
R2348
R2347
R2493
R2342 10K

1K
R2353

R2345

Q2014
R2336 2SC3052
220K

22
0

22
22
22
10K

22
R2352

47
47

22
R2355 R2354 10K
R2356 -

R2359
R2358
R2492
R2364
R2363
R2362
10K R2357 -
C2289 10N-K

22
R2361

R2360
R2485
R2367
5

5
22
22
0
22
22
-
1K

10K
C2290 10N-K R2368

10K
31
32
45
49
50

R2366
R2365
C2291 10/16-Z8154 10K
R2369 22

35 SCL0
TXD2 P4_3

Q2015
36 SDA0

33 P6_5
37 P6_1
38 P6_0
39 P5_7
40 P5_6
41 P5_5
42 P5_4
43 P5_3
44 P5_2
P5_1
46 P5_0
0 47 P4_7
48 P4_6
R2370 22 R2486 0

2SC3052
RXD2 P4_2

R2373
R2372
R2374 22 R2487 0

1K
A0 VCC P7_2 P4_1

R2371
R2375 22
A1 NC R2376 TA1IN P4_0

34 P6_4 31.TXD1
32.RXD1
22

4K7
4K7
P7_4 P3_7

49.P4_5
50.P4_4
A2 SCLK R2377 100
P7_5 P3_6

1 2 3 4
8 7 6 5
GND SDA R2459 22
R2383 P7_6 P3_5
R2378 22
P7_7 P3_4
1K R2460 22 R2382 22

100

100
P8_0 P3_3

R2380
R2494

IC2022
R2381
0 R2384 22
P8_1 P3_2
R2386 22 R2385 22 R2472
P8_2/INT0 P3_1

CW24C16DR
R2387 100K C2293 0
P8_3/INT1 VCC2 330P-J R2388
C2292
R2391 R2390 10K P8_4/INT2 P3_0 10N-K
R2473 22
0 NMI VSS
47K R2389 10K R2392 10K
VCC1 P2_7 R2393 100
C2295
Q2016 D2063 D2062 22P-J XIN P2_6
R2395 - R2488 0

IC2023
ISA1530AC1 R2396
100K VSS P2_5
R2397 22
Q2017 LBAS16HT1G XOUT P2_4

M3030RFGPFP
2SC3052 C2299 R2399 - R2452 -
LBAS16HT1G RESET P2_3
20P
C2300 P8_6 P2_2
R2400
100

R2401 470K 100N-K R2489 0 R2402

R2398

P8_7 P2_1 R2403 100K

6

6
C2301 10N-K 100
R2404 CNVSS P2_0 R2405
R2490 0 47 10K
Q2019 R2406 BYTE P1_7 R2407 47K
2SC3052 10K
TB0IN P1_6/INT4
22
R2495 0 P9_1 P1_5/INT3
Q2020 R2491
R2411 P9_2 P1_4
Q2018

82.P0_6
81.P0_7

ISA1530AC1 R2408 - 0

100.P9_7
R2496 0

99.AVCC
100K P9_3 P1_3
Q2021 R2497 0
RT1N141C

R2413
R2409

P9_4 P1_2
0

2SC3052 R2498 0 47
C2302 P9_5 P1_1 R2414
R2499 0 R2410 -

30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
R2415
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

R2416 470K 100N-K P9_6 P1_0 R2412 47 47

C2303 10N-K 100

99
VREF 98
P10_0 97
AVSS 96
P10_1 95
P10_2 94
P10_3 93
P10_4 92
P10_5 91
P10_6 90
P10_7 89
P0_0 88
P0_1 87
P0_2 86
P0_3 85
P0_4 84
P0_5 83
82
81
ZD2002

100
UDZ15B

Q2022
2SC3052

16M(16P)
XTAL2003
R2417 47K

C2296 1N-K

R2394 680K
C2298 10N-K
C2297 100N-K
R2418 47K
C2305
10N-K
C2304
C2306
R2425
R2424
R2423
R2422

R2426

R2429

R2428
R2427
R2430
R2431

VSX-522-K
10N-K R2421

C2294 100/6.3-Z8156
10P-D
R2419
R2420

R2433 R2432 100

-
-

R2474
0
22
22
22
22
22
-
-

100
100
100

- 120K
Q2023
2SC3052
C2309
C2308

R2436
R2435
R2439
C2307

R2434 -
C2310

10
10N-K

R2437
R2440 10K R2438 -
10K
1N-K
10K
1N-K

R2441
1N-K

R2442 100
7

7
- 120K
Q2024
2SC3052
C2311
10N-K R2443
R2445 R2444 100
- -
Q2025
2SC3052
150(1)

R2447
D2064

10K C2312
R2449 R2448 10N-K
R2446 LBAS16HT1G

C2357
-

330P-J
C2313
100N-K
R2453 R2451 R2450 C2314
R2454

390 330 1K C2317 100N-K

10N-K C2315
0

C2319 10N-K
C2355 330P-J 100N-K

330P-J R2455 C2316

C2356 100N-K
10K C2318
8

8
10N-K
C2320
100N-K

5 4 3 2 1 2 4 6 8 10 12 14 16 18 20 22

CP2005
20010WR-05
1 3 5 7 9 11 13 15 17 19 21 23
CN704B
1.0-11-23P

79
B 1/2 CN404 M CN704AA

D 4/4
F
E
B
A

D
C
 1 2 3 4

10.9 VIDEO, G-L, G-R, WG-B and WG-A ASSYS

A
E VIDEO ASSY (7028071631010-IL)

C1209
R1206 R1207 47/16
75-F 0
R1200
-

B (TV/SAT) C1205 R1257 C1224

68K 100N-K
R1258 C1225
R1204

100N-K

C1226
75-F

C1223

47/16
100N-K
(DVD) 68K 1000N-K Q1208
RT1P141

(TV/SAT)
Q1209
(DVD) C1204 RT1N430C

R1256
R1203

J1200
100N-K
75-F

-
Q1207
RT1N430C J1202
R1255 0
C1206 0
100P-J
R1259 C1238 24P
470 L12
33U
C C1237 24P
R1241
NJM41050VT LOGIC TABLE R1240
R1243
SW1 SW2 MUTE
C1240
IN1 L(OPEN) L(OPEN) H
IN2 H L(OPEN) H
IN3 - H H

2SC3052
MUTE - - L(OPEN)

Q1206
R1239
10

C1239
C1256

R1238
100N-K

560
D

C1233
E 100/16(6.3*11)

C1232
10N-K
R1237
-

: Video Signal Route

(DVD)
: Video Signal Route (DVD)
(TV/SAT)
: Video Signal Route (TV/SAT)

E C CP9

80 VSX-522-K
1 2 3 4
 5 6 7 8

F G-L ASSY (7028071615060-IL) A

* OSD OPTION TABLE

MODEL
CUX/JX SYX FLX/AX/PWX
NO. (NTSC) (PAL) (NTSC / PAL SELECT)
REF. NO.
1 XTAL1200 14M318(18P) NM 14M318(18P)
2 J1200 0-1608 NM NM
3 XTAL1201 NM 17M734(18P) 17M734(18P)
4 J1201 NM 0-1608 NM
Q1207
5 NM NM RT1N430C
Q1209
6 Q1208 NM NM RT1P141C
7 J1202 0-1608 NM 0-1608

Q1208
RT1P141C XTAL1201 R1249

XTAL1200
17M734476(18P)
1K G G-R ASSY (7028071614060-IL)

C1252
100P-J
C1250
Q1209 14M32(18P) IC1203
1M

-
RT1N430C
C1248

LC74781

100/16(6.3*11)
-
J1200

R1244

13 14 15 16 17 18 19 20 21 22 23 24
J1201

C1245

12 11 10 9 8 7 6 5 4 3 2 1
15P-J
-

Q1207
C1249

10N-K

C1251
RT1N430C J1202
0
C1236
C1238 24P-J 18P-J
L1200
33UH(03)
C1237 24P-J C
C1244
R1241 470 100P-J
R1240 470
C1247
10N-K

R1243 470
C1240 10N-K
C1242
100P-J

100P-J
C1243

R1245

560

R1250
100/16(6.3*11)
C1246
2SC3052
Q1206

R1239 R1242
10 2K2 R1248 H WG-B ASSY (7028071617060-IL)
ISA1530AC1

0
C1239

C1241
10P-D

R1247
R1238

Q1210
-
560

5K1
R1246
3K9

BKT3 BKT2

I WG-A ASSY (7028071616060-IL)

E

CLAMP908
CLAMP_WIRE

E F G H I
VSX-522-K 81
5 6 7 8
 1 2 3 4

10.10 BRG-A, BRG-B and BRG-C ASSYS

A
J BRG-A ASSY (7028071633010-IL) K BRG-B ASSY (7028
CP2003
C125Z1-19
D 2/4 CN2003
CP402
1 3 5 7 9 11 13 15 17 19 C125Z1-17
2 4 6 8 10 12 14 16 18
C300
1N-K

(SBL)
(SW)
(SL)
(FL)

C308

(C)
1N-K

CN402
0

CP403
C125Z1-19

A
R816 1K (SBL)
R840

C251SBL C252SBL R817

1
R818 - 10/50 2N2-K 470K

2
C251SBR R814 1K C252SBR R815

3
R819 - 10/50 2N2-K 470K

4
B C251SW R812 1K C252SW R813 (SW)

5
R820 - 10/50 2N2-K 470K (HP)

6
R809 1K (C)

CN403
C251C C252C R811

7
R821 - 10/50 2N2-K 470K

8
C251SL R810 1K C252SL R808 (SL)

9
R822 - 10/50 2N2-K 470K

10
C251SR R806 1K C252SR R807

11
R823 - 10/50 2N2-K 470K

12

A
C251FL R804 1K C252FL R805 (FL)

13
R834 - 10/50 2N2-K 470K

14
C251FR R802 1K C252FR R803

15
R835 - 10/50 2N2-K 470K

16
R800 C252L

17
470K 10/50

18
R801 C251R

19

(HP)
10P-D

10P-D

10P-D

10P-D

10P-D

10P-D

10P-D

10P-D

470K 10/50
-
-
-

-
-

C253
R841
C250SBR

C250SBL
C250SW
R845

R846

R847

R848

R849

R850

R851
R843

R844

C250SR

C250SL
C250FL
C250FR

C250C

C
R842 -
C
2

O CN72

L BRG-C ASSY (7028071635010-IL)

BKT201
CP2002
C125Z1-19
D 4/4 CN2002 CP2001
C125Z1-27 D 4/4 CN2001
BKT-BURRING 27 25 23 21 19 17 15 13 11 9 7 5 3 1
19 17 15 13 11 9 7 5 3 1
4 3 2 1

18 16 14 12 10 8 6 4 2 26 24 22 20 18 16 14 12 10 8 6 4 2
C229 0

C223

1N-K
C228 0
10N-K
C237

D
1.0-11S-10PW
FPC202
1

R839 100
2
3

R837 100
4

R838 100
5
6

R836 100
7
8

R833 100
9

R832 100
10
1.0-11S-10PW
FPC201

E
R831 100
1
2

R830 100
3

R829 100
4
5

R828 100
6

R827 100
7

R826 100
8

R825 100
9

R824 100
10

BKT202
BKT-BURRING CN13 CN16
4 3 2 1

C125Z2-07 2 4 6 8 C125Z2-09
C227 0 1 3 5 7 9

C226 0

F C CP13 C CP16

J K L
82 VSX-522-K
1 2 3 4
 5 6 7 8

ASSY (7028071634010-IL)
A
: Audio Signal Route (L ch)
(FL)
: Audio Signal Route (Front L ch)
(SL)
: Audio Signal Route (Surround L ch)
(C)
C300 : Audio Signal Route (Center ch)
1N-K
(SW)
C308
1N-K : Audio Signal Route (SubWoofer ch)
(SBL)
: Audio Signal Route (Surround Back L ch)
(HP)
: Audio Signal Route (Headphone L ch)

B
100(1/4)

100(1/4)
CP204

R381
C125Z1-09
R380

C380 C381

100/16 100/16

C385 C386
4N7-K 4N7-K

C382 C383
10N-K 10N-K
C384
-
(HP)

C
CP721 CP901
20010WR-04 20010WR-06

O CN721 P CN901

N2001
11 9 7 5 3 1
10 8 6 4 2

D
1
2
3

E
4
5
6
7
8
9

CN204
C125Z2-09

C221 C225 -
1N-K C222
100P-J C224 -
BKT203
BKT-MTG
CN11 1 2 3 4
C125Z2-11

C CP15 F

K L
VSX-522-K 83
5 6 7 8
 1 2 3 4

10.11 FRONT, INSEL, HP, MIC, F-USB and WG ASSYS

A
M FRONT ASSY (7028071621060-IL)
PRESET
PHASE AUTO HVS RDS TP TA PTY ST TUNE ZONE SP AB MEM

kHz
MHz

DTS HD ES 96/24 NEO:6 HD D+EX PLIIx ADV.S. DIGITAL DIR

HDMI

47N(EB)-100V
47N(EB)-100V
B

1/50
56K
56K

56K
56K

56K

56K

56K
56K
56K
56K
56K

56K
56K
56K
56K

56K
56K
56K
56K
56K
56K
56K
56K
56K

56K

56K

56K

56K
1/50

-
-
-
-
-
-

C717
C718
C719
C720

R720

R726
R727
R728
R729
R730
R731
R732
R714
R715
R716
R717
R718
R719

C705
C706
C707
C708
C709
C710
R721
R722
R723
R724
R725
R705
R706
R707
R708
R709
R710
R711
R712
R713
C727 10N-K

C766
-
CP703

R735

44
43
42
41
40
39
38
37
36
35
34
82K
-
R7
39
3 2 1

23 24 25 26 27 28 29 30 31 32 33
11 10 9 8 7 6 5 4 3 2 1
LED
C728 -

100UH(02)

10N-K
C724
10/50

L701
R737 ZD701 IC701
SC16315
C737

Q
R787

15K
10UH(02)

MTZ7.5B RT1N23
-

CN701
C
-

270MM/9P
L702

R779
FL1
R788
1 2 3 4 5 6 7 8 9

FLCT 1(1/4)
-

FL2 R780
GNDU
100/50

1(1/4)
C771

C746

12
13
14
15
16
17
18
19
20
21
22
S CP701 CPU+3.3V
C752

1N-J

CPU_ST_VCC
C767
PDN -
C753
STBY_RLY 1N-J C756 Q707
10N-K -
CPU_ST_VCC C760 C762
C730 1/50 RMC701
- - R34FS9A

Q702
KTA1266GR
R778

R742
R739 470 10K

-
R740 470

R777
47/16

3K3
C736

R741 470

330P-J
10N-K
47/16

100
Q703
100P-J
100P-J
100P-J

RT1N144C

C732
C731
C755

R738
10K
10K

C735
C733
C734

D
R749
R750
820P-K

R754
C738

VOL_UP 100
GNDU
VOL_DN R756
820P-K

R757 R758 R759 R760 R761

C742

100
1K 2K2 3K9 5K6 8K2
SW706

SW701

SW702

SW703

SW704

SW705
C743

1N-K
D709
C751

D707
-

-
-

LUG703 R771 R772 R773 R774 R775

-
1K 2K2 3K9 5K6 8K2
SW708

SW709

SW710

SW711

SW712
C754

1N-K
10K
10K

CP702 CN702
SW715 20010WR-04 80MM/4P
STBY_KEY STBY_KEY
R782
R781
6 5 4 3 2 1

1 2 3 4 5 6

INPUT_UP INPUT_UP R783

E GNDU GNDU 100
820P-K

INPUT_DN
10N-K

INPUT_DN R784
C758
C757

ST_H+5V ST_H+5V 100

POWER_LED POWER_LED
820P-K

C744
R786
C759

SLR-343BC4T(3PI) R789
560

1N-K
0
10N-K
C726

C745 330P-J
D712
C761

D711

-
-

LED704

C765

LUG705
-
C741
Q705 100P-J
RT1N237C
KEY1 (STBY_KEY)

C763 C764
C770 -
POWERDOWN
CPU_ST_VCC

CPU_+3.3V

1N-K 100P-J

1N-K
C768 C769

-
THRU_LED

C740
STBY_RLY

INPUT_DN
FLT_DATA

INPUT_UP

N INSEL ASSY
CNT_LED
ST_H+5V

FLT_CLK

1N-K
GNDU

VOL_DN
VOL_UP
FLT_CE

C739
D+5V
-30V

1N-K
KEY2
KEY3
RMC

F
(7028071623060-IL) 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CN704A
1.0-11S-25
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
CN704AA

D 4/4 CN704B 1.0-11S-23PW

M N
84 VSX-522-K
1 2 3 4
 5 6 7 8

A
(HP)
: Audio Signal Route (Headphone L ch)
AB PRESET
MEM

DIR
HDMI

O HP ASSY (7028071622060-IL)
47N(EB)-100V

B
1/50

10P-J
56K

56K
56K
56K
56K
56K
56K
56K

CN721
-
-
-
-
-

1 9 8 7 3 2 4 5 6
520mm/4P
(HP)
C717
C718
R726
R727
R728
R729
R730
R731
R732
R725

C711
C712
C713
C714
C715
C716

R896 R897

K CP721 0
0

22N-K

22N-K
C749

C750

D706 LBAS16HT1G
JACK701

D705 LBAS16HT1G
R899
R895 0 HP_JACK

100N-K
100

6P-D
R736 R743 R744

C747
C748
390 390 390
LED701 LED702 LED703
- - -
10N-K

10N-K
C729
C724

LUG702
0

1P/130MM
Q701 Q706 C725
R751

RT1N237C

RT1N237C RT1N237C 10N-K

C
Q704

R748
- P MIC ASSY (7028071624060-IL)
0

Q707 Q708
R745

R746

R747

- - Q709
- JACK901
RMC701 R924 R925 MIC
R34FS9A 100 0
CN901
5P_WIRE 260MM R926 0
MIC_DET

100N-K
R742

C913
MIC
-

R901 R902 R903 R904 R911 R912

R927
-9.1V
UDZ5.1B

10/16(3*5)

240 240 240 240

R928
ZD903

1K 1K
C909

GNDA C917 10N-K 0

0
330P-J

LBAS16HT1G
10N-K

LBAS16HT1G
47/16

+9.1V R913 C912

100

5
R907 C908 R910 47
4 3 7 47 1/50(3*5)

10N-K
C905 R905
CP901

6P-D
100K
1 47 1/50(3*5) 8 6
C732
C731
C755

C904 C902
R738

10N-K 10N-K 1/50(3*5) 47 2 C918 10N-K

-
-
UDZ5.1B UDZ5.1B

47K

C914
C919
IC902
ZD901

R917

D902
100P-J
AZ4580

D901
D
100P-J

100K
R914 33K
R906 33K
C903
C901

C910 33P-J
R900

C906 33P-J LUG901

R909
100K

R915

EARTH PLATE
4K7
R908
K

ZD902

4K7

C907

C911
R916

R759 R760 R761 R762 R785

3K9 5K6 8K2 12K 27K

SW703

SW707

SW716
SW704

SW705

R773 R774 R775 R776

3K9 5K6 8K2 12K
SW713
SW711

SW712

SW714

LUG701
1P/100mm Q F-USB ASSY (7028071625060-IL) R E
R3000
WG ASSY
(7028071627060-IL)
0-1608
D 3/4 CP2006
220/6.3
100N-K
100P-J

10N-K
100P-J

1N-K

R3001 CN2006
JACK3000 0-1608 330MM/5P
C3000
C3003

C3002

C3001
C3004

USB+5V
C3005

5 GNDUSB
1
R3008
0-1608

0
C3011

R3002 D-
2
-

R3003 0
D+
3

GNDUSB
4

6
100P-J
CDS3C05HDMI1

CDS3C05HDMI1
-
-
0-1608
R3009

C3012

100N-K
-

C3007

C3008
C3010

C3009

R3004 0-1608
D3001
D3002

R3005 0-1608
-
D3003
LBAS16HT1G
D3004
LBAS16HT1G

0-1608
0-1608
R3006

R3007

C3006

PT706
PLATE
16 18 20 22
17 19 21 23
CN704AA
F
1.0-11S-23PW
04B

M O P Q R
VSX-522-K 85
5 6 7 8
 1 2 3 4

10.12 STANDBY ASSY

S STBY ASSY (7028071632010-IL)

ZD303
RLY301
HL3-1A-6SH MTZ7.5B
1

R336

10K
2

2
R326

4
C304 D301 R333

M CN701
4N7 LBAS16HT1G 33(1)
B

3
1
CP302
LWBP1143-02P D302 3K3
LBAS16HT1G R319
Q301 2K2
2SC3052 Q303
R318

R334
47K 2SC3052

20K
Q302
RT1N144C

9
MTZ15B
ZD302

8
C311

7
-
C307
FLX(WITH CORE)

6
SYX(WITHOUT CORE) ZD301 330P-J

5
only MTZ5.1B
D303

4
CUX,PWX LBAS16HT1G
W300

3
.AX only D304

2
BK
LBAS16HT1G

-
C309
PT301

1
2

100N-K
100/16
F301 D305 1N4007 CP701
1

2200/16(12*16)
D306 1N4007 20010WR-09
WH C302
C CP301

C301
JE202B1T2 J301 1/50 C305
D307 1N4007
W301 100N-K

C306
C303
J302

D308 1N4007
CP303
LBAS16HT1G
LBAS16HT1G

LWBP1143-03P
C315
D310
D309
1

1/50
2

C310

-
3

1
2
522/422

3
CP304
120V(CUXCNSM) 220-230V(SYXCN5) 5267-03A
220V(AXCN5)
110-127 , 220-240V 220-240V(PWXCN)
4
3
2

(FLXCN)

S
86 VSX-522-K
1 2 3 4
5 6 7 8

VSX-522-K 87
5 6 7 8
 1 2 3 4

11. PCB CONNECTION DIAGRAM

11.1 AUDIO ASSY
A
SIDE A NOTE FOR PCB DIAGRAMS : 2. View point of PCB diagrams. SIDE A
1. The parts mounted on this PCB include all Connector Capacitor
necessary parts for several destinations.
For further information for respective SIDE A
destinations, be sure to check with the
schematic diagram.
SIDE B
P.C.Board Chip Part

A AUDIO ASSY

C
IC400

CP17
CN401

C
IC404
D
CP401

CN400
B

Q435
Q433

IC401

IC403

E Q425
IC402
IC406 Q428

Q420
Q422

CN403 CN402
F

J CP403 K CP402
A
88 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE B SIDE B
A

A AUDIO ASSY
B

Q416

Q404
Q401

C
CN401

D
Q402 Q410 Q413 Q418
Q405-Q407
CN400

Q426

Q427

Q432 Q415 Q414 E

Q434

Q419

Q421 Q429

CN402 CN403
F

A
VSX-522-K 89
5 6 7 8
 1 2 3 4

11.2 AMP5 ASSY

SIDE A CP401 A CN400

A

B AMP5 ASSY
CP2005

CN404

B
D

Q408 Q407 Q444 Q443 Q432 Q

Q412 Q448 Q436
Q401 Q437 Q425
Q404 Q409 Q410 Q440 Q445 Q446 Q428 Q443 Q

SIDE B

D
B AMP5 ASSY
CN404

CP401

B Q403 Q406
Q405
Q439 Q442 Q427 Q430

90 VSX-522-K
1 2 3 4
 5 6 7 8

CP402 C CN1 CP403 C CN3 SIDE A

A

Q432 Q431 Q456 Q455 Q420 Q419

Q436 Q460 Q424
Q425 Q449 Q417 Q413
Q443 Q434 Q452 Q457 Q458 Q416 Q421 Q422

SIDE B

CP402 CP403
Q430 Q451 Q454 Q415 Q418
B
VSX-522-K 91
5 6 7 8
 1 2 3 4

11.3 MAIN ASSY

SIDE A
A

C MAIN ASSY

C
CP403

CN3
B

D
CP402

CN1
B

CP1 CP3

POWER TRANS POWER TR

F

C
92 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE A
A

A CN401

CP17

CN3
CP13

L
CN16
C

CP16

L
CN9
CP9

E
CN11
CP15
D

L
CP2004
CN5

D
E

CP3 CP2

POWER TRANS POWER TRANS

F
Q15 Q14
IC5 Q16 Q17

C
VSX-522-K 93
5 6 7 8
 1 2 3 4

SIDE B
A

C MAIN ASSY CP17

B
CP13

C
CP16
CP9

D
CP15
CN5

CP2 CP3

F
Q9-Q13 Q2-Q6

C
94 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE B
A

CN3
CN1 C

P3 CP1

C
VSX-522-K 95
5 6 7 8
 1 2 3 4

11.4 D-MAIN ASSY

SIDE A
A D D-MAIN ASSY

C
CN2006

CP2006

D
Q

F CN2003 CP2004

D J CP2003 C CN5

96 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE A
A

Q2003 Q2002 Q2001

Q2007 Q2006 Q2005

Q2000

IC2006 Q2004

IC2009 IC2000

IC2018
IC2001

IC2003

CP2002
CN2002
IC2005 C

L
IC2004
Q2034
Q2035

IC2021
IC2016

IC2022
IC2019

IC2023
IC2020

IC2014
CP2001

Q2033 Q2031
CN2001

Q2012
Q2015 Q2014
Q2032 Q2030
L

Q2029 Q2027

Q2028 Q2026

Q2016
IC2011
E
Q2020
IC2007

IC2008 Q2018

CP2004 CP2005 CN704B F

C CN5 B CN404 M CN704AA D

VSX-522-K 97
5 6 7 8
 1 2 3 4

SIDE B
A D D-MAIN ASSY

IC2018

IC2002
CN2002

IC2010
C

Q2010

Q2011

D
CN2001

Q2013

Q2019 Q2017

E Q2022 Q2021 IC2011

Q2025

Q2023

Q2024

F CN704B CP2005 CP2004

D
98 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE B
A

CP2006
D

CP2004 CN2003 F

D
VSX-522-K 99
5 6 7 8
 1 2 3 4

11.5 VIDEO ASSY

SIDE A SIDE A
A C CP9

CN9 E VIDEO ASSY

C IC1203

SIDE B SIDE B

E VIDEO ASSY
D

CN9

Q1210 Q1208
Q1207
Q1209
F Q1206 IC1200

E
100 VSX-522-K
1 2 3 4
 5 6 7 8

11.6 G-L, G-R, WG-B and WG-A ASSYS

SIDE A SIDE B
A

F G-L ASSY F G-L ASSY

G G-R ASSY G G-R ASSY

H WG-B ASSY H WG-B ASSY

I WG-A ASSY I WG-A ASSY

E

F G H I
VSX-522-K 101
5 6 7 8
 1 2 3 4

11.7 BRG-A, BRG-B and BRG-C ASSYS

SIDE A
A

J BRG-A ASSY

B
CN2003

CP2003

C
D

CN403
CP403

K BRG-B ASSY

E
CN402

CP402

CP204
A

CP721 CP901

F
O CN721 P CN901

J K
102 VSX-522-K
1 2 3 4
5 6 7 8

SIDE A
A
D CN2002 D CN2001

L BRG-C ASSY CP2002 CP2001

CN13 CN16 CN11 CN204

C CP13 C CP16 C CP15

L
VSX-522-K 103
5 6 7 8
 1 2 3 4

SIDE B
A

CP2001 CP2002 L BRG-C ASSY

CN204 CN11 CN16 CN13

L
104 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE B
A

J BRG-A ASSY

CP2003
C
CP403

K BRG-B ASSY

E
CP402
CP204

CP901 CP721

Q381 Q380
F

J K
VSX-522-K 105
5 6 7 8
 1 2 3 4

11.8 FRONT, INSEL, HP, MIC, F-USB and WG ASSYS

SIDE A
A

M FRONT ASSY
CP701

CN701
S

B
CN702

Q702

N INSEL ASSY
O HP ASSY

CP702 CN721

K CP721

M N O
106 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE A
A
D CN704B

CN704AA

K CP901

P MIC ASSY CN901

Q F-USB ASSY R WG ASSY

CN2006

D CP2006

M P Q R
VSX-522-K 107
5 6 7 8
 1 2 3 4

SIDE B
A

CN704AA

Q709 Q704 Q708 Q706

CN901 P MIC ASSY

R WG ASSY Q F-USB ASSY

CN2006

IC902

M P Q R
108 VSX-522-K
1 2 3 4
 5 6 7 8

SIDE B
A

M FRONT ASSY

CN701
B

CN702
C

IC701 Q703 Q701

Q707

N INSEL ASSY

O HP ASSY

CN721 CP702

Q705

M N O
VSX-522-K 109
5 6 7 8
 1 2 3 4

11.9 STANDBY ASSY

SIDE A SIDE A
A

S STBY ASSY
POWER
TRANS

CP704

CP301

AC IN
M CN701
CP701

POWER
TRANS
CP302
B

SIDE B SIDE B
S STBY ASSY

CP302

E
CP701

CP301
CP704

Q303 Q302 IC301 Q301

S
110 VSX-522-K
1 2 3 4
 5 6 7 8

12. PCB PARTS LIST

NOTES: - Parts marked by “NSP” are generally unavailable because they are not in our Master Spare Parts List.
- The > mark found on some component parts indicates the importance of the safety factor of the part. A
Therefore, when replacing, be sure to use parts of identical designation.
- When ordering resistors, first convert resistance values into code form as shown in the following examples.

Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47 k ohm (tolerance is shown by J = 5%,
and K = 10%).
560 Ω → 56 × 101 → 561 ................................................................... RD1/4PU 5 6 1 J
47 kΩ → 47 × 103 → 473 ................................................................... RD1/4PU 4 7 3 J
0.5 Ω → R50 ................................................................................................. RN2H R 5 0 K
1Ω → 1R0 ................................................................................................. RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62 kΩ → 562 × 101 → 5621 ................................................................. RN1/4PC 5 6 2 1 F

- Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board.
IC 301 (A, 91, 111) IC NJM2068V

- SCHEMATIC DIAGRAM and PCB CONNECTION DIAGRAM → - PCB PARTS LIST

BKT → none BEAD → L RLY → RY SW → S
CLAMP → none F → FU RMC → U VEC → S9***
W → none FLT → V RES → X GND → KN
LUG → none JACK → JA XTAL → X9***
P → none JACK → JA9*** BD → L7***

PACK → 9*** JK → JA LED → D8***

CP → CN PT → T Z → D9***
CP → CN9*** REG → IC ZD → D9*** C
FPC → CN9*** REG → IC9*** DZ → D9***

Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES
NSP 1..PCB TTL ASSY MAIN 7025HK1106010-IL A AUDIO ASSY
SEMICONDUCTORS
2..MAIN ASSY 7028071611060-IL
2..G-R ASSY 7028071614060-IL IC 400 J084152180010-IL
2..G-L ASSY 7028071615060-IL IC 401-403,406 J121458000020-IL
2..WG-A ASSY 7028071616060-IL D 9400,9401 K06006R844520-IL

2..WG-B ASSY 7028071617060-IL MISCELLANEOUS

JA 401 TER,RCA 6PIN G603610A0001Y-IL D
NSP 1..PCB TTL ASSY VIDEO 7025HK1106012-IL JA 402 TER,RCA 2PIN G601206A0005Y-IL
2..VIDEO ASSY 7028071631010-IL JA 403 TER,RCA 1PIN G600107A0000Y-IL
2..STBY ASSY 7028071632010-IL
2..BRG-A ASSY 7028071633010-IL RESISTORS
2..BRG-B ASSY 7028071634010-IL R 510,587 C060033065050-IL
> R 588,589 C060010165060-IL
2..BRG-C ASSY 7028071635010-IL

NSP 1..PCB TTL ASSY AUDIO

2..AUDIO ASSY
7025HK1106013-IL
7028071641060-IL B AMP5 ASSY
SEMICONDUCTORS
NSP 1..PCB TTL ASSY DMAIN 7025HK1106014-IL Q 401,413,437,449 J5001024Y0050-IL
2..D-MAIN ASSY 7028071651010-IL Q 407,408,419,420 J5000992F0050-IL E
Q 412,436,448,460 J5023206Y0050-IL
NSP 1..PCB TTL ASSY AMP5 7025HK1106015-IL > Q 417 J5000992F0050-IL
2..AMP5 ASSY 7028070243010-IL > Q 424 J5023206Y0050-IL

NSP 1..PCB TTL ASSY FRONT 7025HK1106011-IL > Q 425 J5001024Y0050-IL

2..FRONT ASSY 7028071621060-IL Q 431,432,443,444 J5000992F0050-IL
2..HP ASSY 7028071622060-IL Q 455,456 J5000992F0050-IL
2..INSEL ASSY 7028071623060-IL D 9401,9404,9407,9410 K06005R134520-IL
2..MIC ASSY 7028071624060-IL D 9402,9403,9405,9406 K06004R344520-IL

2..F-USB ASSY 7028071625060-IL D 9408,9409,9411,9412 K06004R344520-IL

2..WG ASSY 7028071627060-IL D 9413 K06005R134520-IL
D 9414,9415 K06004R344520-IL F

MISCELLANEOUS
VR 401-405 VR,SEMI CARBON MOLD C541102315000-IL

VSX-522-K 111
5 6 7 8
 1 2 3 4

Mark No. Description Part No. Mark No. Description Part No.

RESISTORS
400 BRACKET 4010210196100-IL
D D-MAIN ASSY
SEMICONDUCTORS
A
> R 406,450,494,537 F320184710050-IL > IC 2004 NJM2831F33
R 424,425 N113136647820-IL > IC 2005 S-1170B18UC-OTD
> R 430,431,467,468 N113136647820-IL IC 2009 J040740400270-IL
R 443,487,530,573 C060047065060-IL IC 2010 TC74VHC157FK
> R 474,475,511,512 N113136647820-IL IC 2011 AK4588VQ

> R 493 C060033065050-IL IC 2014 J040742570040-IL

> R 517,518,554,555 N113136647820-IL IC 2018 J001986466010-IL
> R 561,562,597,598 N113136647820-IL IC 2020 J040740800240-IL
> R 580 F320184710050-IL IC 2021 341S2162
> R 603,604 N113136647820-IL IC 2022 J000241600170-IL

B
R 616 C060047065060-IL Q 2034 J543608000010-IL

CAPACITORS MISCELLANEOUS
C 419 D04010108C240-IL JA 2005 TER,RCA 1PIN G600107A0000Y-IL
JA 2006 OPTICAL RECEIVER E100116500040-IL
X 2000 CRYSTAL (24 MHz) E80024R000030-IL

C MAIN ASSY
SEMICONDUCTORS
X 2001
X 2002
CRYSTAL (18.432 MHz)
CRYSTAL (24.576 MHz)
E80018R432050-IL
E80024R576030-IL

> IC 1 J126781200040-IL X 2003 CRYSTAL (16 MHz) E80016R000030-IL

> IC 2 J126791200060-IL
> IC 3 J126780500110-IL RESISTORS
Q 14,15 J5023198Y0000-IL R 2446 C060015165050-IL
C Q 16 J5000992F0050-IL

>
>
Q
D
D
17
7
9
J5000916Y0050-IL
K047100600220-IL
K047604000020-IL
E VIDEO ASSY
SEMICONDUCTORS
> D 10-13 K000400700220-IL IC 1200 J127410500010-IL
D 23 K000400700220-IL IC 1203 J170747810010-IL

D 9001 K06003R344520-IL MISCELLANEOUS

D 9024,9025 K06016R044520-IL JA 1200 TER,RCA 3PIN G606305AW140Y-IL
X 1200 CRYSTAL (17.734476 MHz) E80014R318080-IL
MISCELLANEOUS
JA 101 TER,BOARD SCREW 4P G612405E0200Y-IL
JA 102 TER,BOARD PUSH 4P G594408SA030Y-IL
F G-L ASSY
D
JA 9101 TER,BOARD PUSH 2P G592212A0300Y-IL
RY 2-4 RELAY G680120502050-IL There is no service parts.
CN 9009,9016 CN.WAFER L109012510720-IL

CN 9013
CN 9015
CN 9017
CN,WAFER
CN,WAFER
CN,WAFER
L109012510720-IL
L109012511120-IL
L109012511120-IL
G G-R ASSY
There is no service parts.
601 TUNER,FM/AM E903004100780-IL

RESISTORS
R
R
5,7,9,11
6,8,10,12
C060010065050-IL
C060010066050-IL
H WG-B ASSY
There is no service parts.
E R 13,25 C060010065050-IL
R 14 C060010066050-IL
R

R 64
27,31,41,42 C060R22065050-IL

C060022063050-IL
I WG-A ASSY
There is no service parts.
R 66 C0604R7065050-IL

CAPACITORS
C
C
55,58
73
D040682088010-IL
D040682083000-IL
J BRG-A ASSY
MISCELLANEOUS
C 84 D040472084020-IL CN 403,2003 CN,WAFER L109012511920-IL
C 85 D040102084060-IL
C 101 D040331088230-IL
F

112 VSX-522-K
1 2 3 4
 5 6 7 8

Mark No. Description Part No. Mark No. Description Part No.

K BRG-B ASSY
MISCELLANEOUS
RY 800
CN 204
RELAY
CN.WAFER
G680240202030-IL
L109012510920-IL
S STBY ASSY
SEMICONDUCTORS
A

CN 402 CN,WAFER L109012511720-IL > IC 301 J126111700041-IL

> D 303,304 K005041480230-IL
RESISTORS > D 305-308 K000400700220-IL
> R 380,381 C060010163050-IL D 9301 K06005R144520-IL
R 382 C060010063050-IL D 9302 K06015R044520-IL

D 9303 K06007R544520-IL

L BRG-C ASSY
MISCELLANEOUS
MISCELLANEOUS
> RY 301 RELAY G680060102020-IL
CN 2001 CN.WAFER L109012512720-IL > T 301 POWER TRANS 8200280150620-IL B
CN 2002 CN,WAFER L109012511920-IL > CN 301 CONNECTOR L108202000220-IL
201,202 BRACKET 4010210196100-IL > CN 302 CN.WAFER 7.92MM L108011430210-IL
302,303 BRACKET 4010210196100-IL

M FRONT ASSY
> FU 301 FUSE GLASS TUBE 20MM (T6.3AL250V)N751506301160-IL

SEMICONDUCTORS RESISTORS
IC 701 J127163150010-IL R 326 C060033065050-IL
> Q 702 J5001266G0050-IL
D 8701 K06007R544520-IL CAPACITORS
D 9701-9703 K500052009011-IL C 301 D040222083010-IL
> C 304 D00847208H010-IL
MISCELLANEOUS C
H 701 FL HOLDER 4320211016000-IL
V 701 DISPLAY,FLT K530126600010-IL
S 701-714,716 SWITCH G180501000010-IL
S 9701 SW,ENCODER G121125042011-IL
U 701 MODULE,REMOCON E940349003810-IL

RESISTORS
R 779,780 C060001063050-IL

N INSEL ASSY
MISCELLANEOUS D
S 715 SWITCH G180501000010-IL
S 9702 SW,ENCODER G121125052011-IL

O HP ASSY
MISCELLANEOUS
JA 701 JACK,D6.5 G402PJ612A09Y-IL

P MIC ASSY
SEMICONDUCTORS
E

IC 902 J121458000020-IL

MISCELLANEOUS
JA 901 JACK,D3.5 G401PJ354H40Y-IL

Q F-USB ASSY
MISCELLANEOUS
JA 3000 CN,PLUG CONTACT G480040000180-IL

R WG ASSY
There is no service parts.

VSX-522-K 113
5 6 7 8