DEMONSTRATION PANEL FOR THE
DP
ELECTRIC TESTING CARRIED OUT
IN INDUSTRIAL BUILDINGS
Mod. PDG-2/EV
INTRODUCTION
This panel can be used by teachers for their lessons and by
students for an easy learning and testing on electrical prevention
systems supplying them with the means for verifying the rule of
art and the relevant technical standards.
Actual electrical devices installed, already connected with each
other, enable to check the operation, besides carrying out the
measurements of all the electric parameters with conventional
instruments.
The panel is made of insulating material and it represents the
ELECTRICAL ENGINEERING
support of the necessary devices for carrying out the testing
programme. The apparatuses are represented on the panel
with their standardized international symbols, electrical block
diagram and lay-out, for an easy reference. Furthermore, when
necessary, test points correspond to standardized educational
terminals with high protection degree against accidental
contacts. Four switchboards including the protection devices
(main switchboard, department switchboards) are available in
the rear part of the equipment.
TRAINING PROGRAM:
This panel can be used to define the electrical installations of Furthermore, this panel is designed to deal with topics,
an industry (power distribution via TN system) with reference visual checks, tests concerning:
to the following topics:
• Analysis of diagrams and documents, warning signs
• Design of the electrical installation in industrial sheds
• Suitability of materials and of equipment
• Main switchboard (cabin switchboard)
• Protection against direct contacts
• Department switchboard
• Protection against indirect contacts
• Distribution by channel or by ducts-bars
• Precautions against fire starting and propagation
• Installation plans
• Breaking devices for servicing
• Graphical symbols for installation plans
• Functional and emergency control devices
• Earth plates and plan of earthing systems
• IP protection degree of cases
• Installations in places with risk of explosion
• Identification of circuits, of fuses, of operation switches
• Installations in places with risk of fire
• Suitability of the connections of conductors
• Drawing up Form A (atmospheric discharges) and Form B
• Checking the current-carrying capacity of ducts
(earthing systems)
• Checking the section of the protection conductor according
to fault current
• Correct choice of protection devices against overcurrents
• Continuity tests of protection and equipotential conductors
• Measurement of isolation resistance
23C-E-DP-PDG2-1
• Measurement of fault loop impedance
• Polarity tests
• Analyzing the functionality of differential circuit breakers
ELETTRONICA VENETA S.P.A. - 31045 Motta di Livenza (TV) Italy - Via Postumia 16 - Tel. +39 0422 765 802 - Fax +39 0422 861 901 - E-mail: [email protected] DP 21
TECHNICAL SPECIFICATIONS:
DP
Framework is made of sheet steel chemically treated and
painted with several coats of epoxy varnish; its base is provided
with rubber feet and it can be positioned on a working top.
All the necessary electric components for the correct power
supply of circuits are included in the panel.
Main components installed:
• 1 three-phase isolation transformer 230-400 V / 230-400 V
750 VA
• 1 simulator of cabinet earthing system with 3 fixed
resistances of 1 Ω
• 1 four-pole magnetothermal circuit breaker 4 x 6 a,
curve C, with releasing coil
• 1 delayed differential relay of 0.03-1 A, with detecting TA
• 2 sets of three fuse holders with fuses of 2 A
• 1 magnetothermal differential circuit breaker
4 x 3 A “C” / 0.3 A “S” “A”
• 1 magnetothermal differential circuit breaker
2 x 1.6 A “C” / 0.3 A “AC”
• 1 magnetothermal differential circuit breaker
ELECTRICAL ENGINEERING
2 x 0.5 A “C / 30 mA “AC”
• 1 magnetothermal differential circuit breaker
2 x 1 A “C / 30 mA “A”
Dimensions of demonstration panel: 800 x 600 mm
Dimensions of framework: 840 x 450 x 680 mm
Net weight: 50 kg
SUPPLIED ACCESSORIES:
• 1 single-phase power cord with EEC socket and plug
• 3 jumpers with safety plugs (Ø 4 mm) for assembling
the various installation conditions
RECOMMENDED ACCESSORIES:
• Multi-function microprocessor instrument
for electric testing
• Digital current probe
• Digital autoranging multimeter
• Electric CAD for Windows
POWER SUPPLY:
3 x 400 V / N / PE 50-60 Hz
Max. absorption: 750 VA
23C-E-DP-PDG2-1
THEORETICAL-EXPERIMENTAL
HANDBOOKS
Application handbook with exercises.
DP 22 ELETTRONICA VENETA S.P.A. - 31045 Motta di Livenza (TV) Italy - Via Postumia 16 - Tel. +39 0422 765 802 - Fax +39 0422 861 901 - E-mail: [email protected]
