Dynapac Operation, Maintenance

& Parts Manual

EZIV 10’ SCREED SERIAL # ______ _

800-889-0661
800-889-0661

DynapacParts.com
DynapacParts.com
 DynapacParts.com
800-889-0661
18452 50th Ave. E., Tacoma, WA 98446
Ph: (253) 875-8000 Fax: (253) 846-0100
www.carlsonpavingproducts.com

EASY SCREED IV
10’
Operation/Service & Parts Manual
DYNAPAC 10’ Tractor

DynapacParts.com
800-889-0661
 INTRODUCTION 1

OPERATION ~ ADJUSTMENTS 2
Table
DynapacParts.com MAINTENANCE 3

of BASE MACHINE ~ BILL OF MATERIALS 4

800-889-0661 PLATE GROUP 5

Contents TRACTOR PARTS, UPPER DRIVE

GROUPS, SCREED ARMS
6

MAIN SCREED HEATING ELEMENTS 7

THERMOSTAT 8

RIGHT & LEFT EXTENSION SCREEDS 9

MAIN STAIR 10

END GATES, SAFETY EDGE 11

HYDRAULIC LINES GROUP 12

BERM GROUP 13

MANIFOLD ASSEMBLY 14

DEPTH SCREWS 15

REMOTE GROUP 16

END GATE JACKS 17

BOLT ONS , TAPERED JOINT 18

BEVELED EDGER 19

CUT OFF SHOE 20

DynapacParts.com ELECTRICAL SYSTEM 21

800-889-0661
CARLSON PAVING PRODUCTS 22

OPERATORS MANUAL 23
 Carlson Paving Products Inc.
Parts & Maintenance

EASY SCREED IV
DynapacParts.com
800-889-0661
10’
FLAT TAIL
Dynapac F1000 Tractor Paver

Carlson Paving Products Inc.

18425 50th Ave. E.
Tacoma, WA 98446
Phone: (253) 875-8000
Fax: (253) 846-0100

DynapacParts.com
800-889-0661
REVISED 08-04-11

Page 1 of 251
 CONTACT LIST

DynapacParts.com
Chris Colwell
Cheryl Ratfield
- President/General Manager
- Controller

800-889-0661
Becky Pudists - Human Resource Manager
Ben Moody - Purchasing Manager
Kevin Comer - Engineering Manager
Robert Chase - Manufacturing Manager
Katy Gallagher - IT Administrator
Tracy Lambert -Northwest Regional Manager (WA, MT, OR, ID & Northern CA)
Kevin Jeske - Great Lakes Regional Manager (WI, MI, IL, IN, OH & KY)
Robert Shimp - Northeast Regional Manager (MA, VT, NH)
Gary Morris - Tennessee Valley (MS, TN, VA, WV, NC & SC)
Matt Schlosser - Mid Atlantic Sales Manager
Kevin Trahan - South Central Regional Manager
Bubba Carden - Southeast Regional Manager (AL, GA & FL)
Bill Wright - North Central Regional Manager (CO, IA, KS, MN, MO, ND, NE, SD & WY)
David Kajitsu - Parts Manager
Mike Welch - Service Manager
Tim Collins - Service Coordinator
Karl Rowan - Service Technician
Bubba Carden - Service Technician

Carlson Paving Products, Inc.
18425 50th Ave. E. Tacoma, WA 98446
Ph (253) 875-8000 – Fx (253) 846-0100
Chris Colwell , President/G M -Mobile (253) 691-6354
Robert Chase, Manufacturing Mgr. Mobile (253) 278-9418
Becky Pudists, HR Mgr. -Mobile (253) 302-1006
Katy Gallagher, IT Admin -Mobile (253)306-3858
Tom Travers, Sales & Mkt. Mgr -Mobile (253) 278-9426

DynapacParts.com
Bill Wright, North Central Mgr. -Mobile (253) 312-8410
Kevin Trahan, Southeast Mgr. -Mobile (253) 278-9421
Kevin Jeske, Great Lakes Mgr. -Mobile (253) 278-9423
Gary Morris, Tennessee Valley -Mobile (253) 208-2926

800-889-0661
Kevin Comer, Engineering Mgr. -Mobile (253) 548-7564
Mike Welch, Service Mgr -Mobile (253) 278-9422
David Kajitsu, Parts Mgr. -Mobile (253) 341-1946
Robert Shimp, Northeast Mgr -Mobile (253) 208-8168
Tracy Lambert, Northwest Mgr. -Mobile (253) 320-5597
Karl Rowan, Service Tech -Mobile (253) 341-1077
Bubba Carden, Service Tech -Mobile (253) 278-0065
www.carlsonpavingproducts.com

Page 2 of 251
 TABLE OF CONTENTS
INTRODUCTION:

DynapacParts.com
1. WARRANTY, PAVING THEORY, PAVER SPEED, HEAD OF
MATERIAL

OPERATION:
2. 800-889-0661
ADJUSTMENTS:
ANGLE OF ATTACK
TROUBLESHOOTING GUIDE
PRE-STRIKE OFF ADJUSTMENTS
PLATE REPLACEMENT
SCREED SHIMMING
SLIDE ADJUSTMENT
LEAD CROWN ADJUSTMENT
EXTENSION SCREEDS
LEVELING
SLOPE ADJUSTMENT
BOLT ONS
WIDE PAVE BRACKET
SLIDE ADJUSTMENT
BERM EFFECTS

MAINTANENCE:
3. LUBE CHARTS & SCHEDULES
SPECIFICATIONS - TRANSPORT

REPLACEMENT PARTS:
4. BASE MACHINE:
EZIV-10 BASE MACHINE (201-998-003)
FRAME GROUP
OVEN
EXTENSION GROUPS
COVER GROUP
CROWN

DynapacParts.com
WALKWAY GROUP
EXTENSION CYLINDER
DECAL GROUP

5.
800-889-0661
PLATE GROUP

Page 3 of 251
REQUIRED OPTIONS:

6. TRACTOR SPECIFIC PARTS

STAIRS, UPPER DRIVE GROUPS, SCREED ARMS
& SONIC AUGER SENSOR MOUNT

7.
DynapacParts.com
MAIN SCREED HEAT ELEMENTS:
202-561-100 STANDARD

8.
800-889-0661
THERMOSTAT:
1044-0145 THERMOSTAT AS. 330 DEGREE

9. RIGHT & LEFT EXTENSION SCREEDS:

201-990-000 & 201-991-000 STRAIGHT
201-992-000 & 201-993-000 12”
201-994-000 & 210-995-000 18”
201-996-000 & 201-997-000 24”

10. MAIN STAIR

11. END GATE

202-991-000 STANDARD (HWE)
203-340-000 STANDARD HEATED ELEMENT KIT
202-875-600 TAPERED ENDGATE ASSEMBLY – RH
202-875-700 TAPERED ENDGATE ASSEMBLY - LH

12. HYDRAULIC LINES GROUP

13. BERM GROUP

202-908-000 HYDRAULIC AS. – BERM 24V - 12" EZIV 10'
202-909-000 HYDRAULIC AS. – BERM 24V - 18" EZIV 10'
202-910-000 HYDRAULIC AS. – BERM 24V - 24" EZIV 10'

14. MANIFOLD ASSEMBLY

1030-0025 SOLENOID VALVE 24V

15. DEPTH SCREWS

OPTIONAL
16.
17.
18.
DynapacParts.com
REMOTE GROUP
KIT – JACK SPRING LOADED
BOLT ONS - WIDE PAVE BRACKET
19.
20.
21.
800-889-0661
BEVELED EDGER
CUT-OFF SHOE
ELECTRICAL SYSTEM & GENERATOR
22. CARLSON PAVING PRODUCTS
23. OPERATORS MANUAL

Page 4 of 251
 DynapacParts.com
800-889-0661
18452 50th Ave. E., Tacoma, WA 98446
Ph:(253) 875-8000 Fax:(253) 846-0100
www.carlsonpavingproducts.com

WARRANTY
Carlson Paving Products, Inc., warrants all new equipment of Carlson
Paving Products, Inc., Manufacture, to be free from defects in material
and workmanship for a period of twelve (12) months or 1,000 hours,
whichever comes first, after in service date to the original purchaser,
when subject to normal and proper usage. Written notice must be
given to Carlson Paving Products, Inc., upon discovery of such defects
and part returned, freight prepaid. If parts are found defective by
Carlson Paving Products, Inc., by inspection, the part will be repaired
or replaced without cost to purchaser, freight out bound, from factory
point of manufacture. The foregoing shall be the limit of Carlson
Paving Products, Inc., as these items are subject to the warranty of
their respective manufacturers.

Except set forth therein, there is no warranty of merchantability, nor

other warranty, express, implied or statutory, nor any affirmation of
fact, or promises by Carlson Paving Products, Inc., with respect to
equipment covered herein, in no event shall Carlson Paving Products,

DynapacParts.com
Inc., be liable for special, indirect or consequential damages, nor for
any delay in performance of the warranty due to causes beyond its
control.

800-889-0661

Page 5 of 251
 New Screed Delivery Report & Warranty Registration
This report must be completed and returned to Carlson Paving Products, Inc. immediately. All warranty periods for
machine will start only after this form has been submitted and the warranty period for this machine has been started by the
submittal of this form. Failure to return this form will result in a non-valid warranty period or possibly void the warranty of
the machine completely.

DynapacParts.com
Dealer Customer
Name: Name:
Address Address:

800-889-0661
City,ST, Zip: City,ST, Zip:
Contact: Contact:
Phone Phone:
Fax: Fax:

Machine Information
Screed Model: Paver Year:
Screed serial No Installed by:
Paver model: Install date:
Paver serial No In service date:
DELIVERY INSPECTION
(Please initial each box when completed)
Valve functions correct. End gate jacks correct.
Depth screws rotation and decal correct. Right hand berm correct width.
Left hand berm correct width. Right hand extension leveled correctly.
Left hand extension leveled correctly. Heat system operational.
Vibrator system operational. Accessory power outlets working.
Grease points. All tractor electrical controls functioning correctly.
All hydraulic adjustments set and locked properly. Generator speed checked. In all operating modes.
Hydraulic reservoir in tractor checked after install. All hydraulic hoses protected or supported properly.
Bolt on extensions fit and adjusted. If equipped. Additional pumps for tractor checked for pressure.
Main screed lead crown set to no more than 1/8 Screed attachment bolts tight.
Check case drain on generator drive motor Cut-Off shoes fit and adjusted. If equipped.
All hydraulic hoses inspected & tight. Rear of main screed shimmed properly.

Name of operator instructed:________________________________________________________

Name of mechanic instructed:_______________________________________________________

Explain all discrepancies and actions taken:

___________________________________Machine shipped on
___________________________________________________________________________________________________
___________________________________________________________________________________________________
___________________________________________________________________________________________________

Signatures below indicate that all functions and operations of the screed were checked, are complete, in good order and that

DynapacParts.com
the customer understands the warranty period and procedure of the machine.
Customer name Title Inspection completed by

800-889-0661
Customer signature Date Inspectors signature

Page 6 of 251
Paving Theory
Asphalt paving is not an exact science. A screed operator is, in essence, an artist. The
finished mat is a direct reflection of his or her ability to control the screed and reduce as
many variables associated with asphalt paving as possible. The problem is that there are
infinitely more variables that can affect the paving operation than most people realize. To
produce a mat that has a consistent texture and density requires that all variables stay as

DynapacParts.com
consistent as possible.

Paver Speed

800-889-0661
Paver speed has a direct effect on how a screed will react while paving. A screed rides
over asphalt in the same manner that an airplane wing flies through the air. When an
airplane is flying at a certain altitude, then increases its speed, it will rise. A screed will
react in the same manner. When a paver increases its speed, the head of material is forced
against the front section of the screed at a greater pressure. This pressure is what makes
the screed rise. The opposite is true if the paver decreases its speed.
When a paver has to consistently start and stop, the speed it is traveling is not consistent,
and the screed will not ride on a flat plane. The screed will tend to rise and fall making it
hard to keep the mat consistent.

Head of Material
The head of material is the asphalt that is carried in front of the screed, in and around the
augers at all times, while paving. To reduce the variables associated with the head of
material, the operator should attempt to keep the head of material as consistent as
possible. There is no need to carry any more material in front of the screed than is
required to feed the entire length of the screed while paving. Once you have determined
this amount, you should try to keep this level the same. If the head of material decreases,
the pressure at the front of the screed will decrease, causing the screed to drop. This
causes voids to appear in the mat. To control the head of material, adjust the flow gates
on the tractor up or down until the head of material stays the same.

Angle of Attack

In order for a screed to produce a mat that has consistent density and texture, the pressure
exerted by the rear of the screed plate must be equal along the entire plate. The same is
true with extensions. The EASY SCREED has been designed so it is as simple as
possible to adjust these pressures while paving, allowing the operator to control the mat
texture and density while paving.

DynapacParts.com
800-889-0661

Page 7 of 251
 ~CAUTION~
WHEN FINISHED PAVING, AND WHEN
LOADING PAVER ON TRAILER, ENSURE SCREED

DynapacParts.com
EXTENSIONS ARE RAISED ABOVE THE BOTTOM
LEVEL OF THE MAIN SCREED TO PREVENT
CATCHING EXTENSION BOTTOM ON TRAILER

800-889-0661
OR OTHER OBSTRUCTION WHILE MOVING
PAVER.

CAUTION
LEFT HAND EXTENSION
MUST BE EXTENDED 6”
BEFORE SLOPING DOWN

DO NOT USE DIESEL

ON CHROME
EXTENSION RODS

IF RODS BEGIN TO CHATTER

DynapacParts.com
WHILE RUNNING
EXTENSIONS IN OR OUT

800-889-0661
APPLY DRY TEFLON
SPRAY

Page 8 of 251
 Angle of Attack Adjustment
The Easy Screed extension has an external angle of attack adjustment on each extension.
This is a critical adjustment for mat texture between the main screed and Easy Screed
extension.

DynapacParts.com
By raising the bull nose on the Easy Screed extension, we force more mix under the
extension. If you raise the bull nose up too high, a shiny mat will occur behind the
extension. Too low and a loose mat will occur behind the extension.

800-889-0661
When the angle of attack on the extension is too high, the main screed will lay a loose
mat because we are transferring the weight from the main screed to the extension. When
the angle of attack is too low, the main screed will be tighter than the extension.

…Summary: OUR OBJECTIVE IS TO LAY A UNIFORM MAT

Whenever the mat is loose and open or tight and shiny behind the extension, it must be
uniform. If the mat under the main screed is loose and open and the mat under the
extension is tight and shiny, lower the angle of attack under the extension until the entire
mat is uniform.

If the mat under the main screed is tight and shiny and the mat under the Easy Screed
extension is loose and open, raise the angle of attack on the extension until the entire mat
is uniform.

DynapacParts.com
800-889-0661

Page 9 of 251
 This mat (under extension) is
too tight and shiny: The angle
of attack jack should be turned
approximately one revolution
~counter-clockwise~ to push

DynapacParts.com the bull nose down to decrease

mix feeding under the screed
extension, thus transferring

800-889-0661
more weight to the main
screed. Note: When changing
angle of attack, it is necessary
to turn the berm screw in the
same direction until null. (Use
the same direction that the angle of attack jack was turned.)

If the mat is loose under the

extension then it will be
necessary to raise the bull
nose on the screed extension.
To raise the bull nose turn the
angle of attack jack clockwise
to tighten the mat behind the
screed extension, then it will be
necessary to turn the berm
screw in the same direction
until it is null.

Figure 2

This is the correct angle of

attack.

DynapacParts.com
800-889-0661 Figure 3

Page 10 of 251
The following picture (Figure 4) is showing several different mat textures. The screed in
the picture label (1) is laying down 3” of asphalt on the right hand side, and scratching
on the left hand side. The left hand screed extension, when scratching, is lifting the
weight from the main screed. If you look at the mat in label (2) it is a loose mat all the
way to the center of the screed because there is basically no PSI under the screed because
of the left hand screed extension scratching. The whole left hand side of the screed is in
reality, just like a strike off, and not a screed. On the other hand if we look at the right

DynapacParts.com
hand side we are laying 3” of asphalt, and the mat texture looks relatively good because
there is weight on the mat from the screed.
If we look close to the mat in label (4) and compare it to figure 3 we see the results of too

800-889-0661
much angle of attack in the right hand screed extension. This should be decreased until
the mat looks like figure 3.

Figure 4

DynapacParts.com
800-889-0661

Page 11 of 251
 DynapacParts.com
800-889-0661
This is to assist you in identifying and correcting problems you may experience in usage of Easy Screed.
Numbers indicate troubleshouting sequence

CONDITION:
(Exhibit "D") (Exhibit "A")
Tearing (Exhibit "C") (Exhibit "B") Tight Screed
Tight / Shiney Loose mat
Screed riding behind Loose & dark / shiney mat extensions
on nose main streak 2" wide in
streak 4-10"
behind screed
behind the
leaves
POSSIBLE OR LIKELY PROBLEM
wide in mat screed
screed center of mat extension ripples in mat
center extensions

1 Prestrike-off too low

3 Prestrike-off too high
2 2 Head of material too low
5 Head of material too high
3 Cold mix
2 Bull nose of main screed worn
4 1 Angle of attack in extension set too high
4 1 Angle of attack in extension set too low
1 Screed extension is loose
1 Too much lead crown
2 Negative lead crown
1 Mat thickness less than bull nose radius
7 Screed lift cylinders bottomed out
6 Screed lift cylinders are not free floating
5 Possible segregation from truck loading or dumping
1 Mix falling to the center of the chain box

DynapacParts.com
800-889-0661 Page 12 of 251
 DynapacParts.com
800-889-0661
CONDITION:
Inside of screed
Inside of
Outside of extension digs Extension
screed Screed rides Main screed Short ripples in
main screed into mat & outside mat not
leaves
extension
of main screed
too high in wears fast
level with
the mat at 12" POSSIBLE OR LIKELY PROBLEM
digs into front in center intervals
windrow of mix leaves a windrow main mat
mat
of mix
1 Prestrike-off too low
6 Head of material too high
7 Screed pivot point loose / worn
2 Automation set too sensitive
3 All variables in front of screed not fixed
3 Main screed needs to be shimmed
8 Loose / worn mat thicknes control screws
2 Screed extension is loose
1 4 Too much lead crown
4 Screed lift cylinders bottomed out
5 Screed lift cylinders are not free floating
1 Screed extension too high
1 2 Screed extension too low
2 2 2 3 Screed extension not leveled correctly
1 1 Berm is not level
1 Screed riding on its nose

DynapacParts.com
800-889-0661 Page 13 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 14 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 15 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 16 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 17 of 251
Pre-Strike-off Adjustments
The front of the Easy Screed IV is formed with a radius that is equal to the extension screeds.
In most cases, the pre strike-off plates should be adjusted so they are above the top edge of the bend
in the bull nose. This is 1/2” above the bottom of the screed plate.

DynapacParts.com
Due to the number of mix designs, it may be necessary to adjust the pre strike-off plates to
force the screed to ride correctly over the mat being laid.
Look at the side of the screed while it is paving. In order to get the maximum of life from a

800-889-0661
screed plate, the screed must be riding correctly over the mat while it is paving. If the screed is tipped
forward on the nose, the front section of the screed will have excess wear. (See figure 1) Also if the
screed is tipped to far back, the rear section of the screed will have excess wear (see figure 2). The
screed should be tipped up slightly in the front so that the weight of the screed is evenly distributed
across the screed plate. (See figure 3).
If you lower the pre strike-off plates, you will decrease the amount of material felt at the front
of the screed, causing the front of the screed to drop in comparison to the rear of the screed. If you
raise the pre strike-off plates the opposite will happen. Adjusting the pre strike-off plates will not
necessarily change the depth at which you are paving, but will change the attitude of the screed as it
passes over the mat.
Use the adjusting bolts located at the top of the mold board of the main screed frame to adjust
the height of the plates. Turn the bolts counter clockwise to raise the plates and clockwise to lower
the plates.
The factory setting on the pre strike-off plate is at least 1/2” above the bottom of the main
screed plate. If you find it necessary to adjust the plates to do a particular job try starting the adjusting
plates to ½” above the screed and fine tune from there.

**NOTE** If there is too much angle of attack in the extensions, the main screed will have a
tendency to ride on its nose. Be certain the angle of attack is adjusted correctly on each extension
before attempting to adjust the pre strike-off plates to correct a screed ride problem. Refer to angle of
attack adjustment earlier in manual.

DynapacParts.com
800-889-0661

Page 18 of 251
 This screed is riding on its nose

DynapacParts.com
800-889-0661
Figure 1

This screed is riding on its tail

Figure 2

This screed is riding correctly

DynapacParts.com
800-889-0661 Figure 3

Page 19 of 251
Screed Plate Replacement

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 20 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 21 of 251
 DynapacParts.com
800-889-0661

Make sure that the elements are held in place by the clip on the inside ends of the element.
Zip tie the outside end of element.
Install heat cote to the underside of the elements and install the new plate.

DynapacParts.com
800-889-0661

Page 22 of 251
Shimming the Main Screed Plate

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 23 of 251
Lead Crown Adjustment
Lead Crown is having more crown in the nose (front) of the main screed plate then on the rear
edge. Lead crown allows extra material in the center of the mat to allow for compaction of the
material.

DynapacParts.com
Please follow the steps below to check and/or set Lead Crown

1) Pick up screed. Place safety stands under screed for safety.

800-889-0661
2) Move tow points on paver till tow points are equal.
3) Turn Screed Depth screws till both screws are Null.
4) By using straight edge or string line check Crown in nose (front) of screed.
The best location for this is about the second row of cones back.
This can be easily seen because you can see the end of the stud sticking through
the plate. If you can’t see the stud, you can always remove the cover on the
side of the main screed frame to easily see this location.
5) Adjust the crown till the nose of screed has 1/16 of positive crown screed plate.
6) Now check the rear edge of the screed plate with a straight edge/string line
Adjust rear cones so rear edge of screed plate is completely flat.
7) Make sure crown gauge is reading accurately. If no, reset gauge to zero.

**NOTE** If after setting the screed to these standards, and the screed does not pave correctly,
consult the factory for further help.

DynapacParts.com
800-889-0661

Page 24 of 251
Extension Screed Leveling & Slope Adjustment

DynapacParts.com
800-889-0661

To level the berm, adjust the

stroke of the berm cylinder to
the desired length to get the
berm level on the straight
edge.

After adjusting raise and

lower the berm hydraulically
and re-check.

DynapacParts.com
800-889-0661

Page 25 of 251
DynapacParts.com
800-889-0661

1) Is the berm level?

2) Retract the extension.

3) In the operator control box

lower or raise the screed height
hydraulically so the rear of the
screed extension is flush with the
main screed.

4) Holding the level in place

extend the extension all the way
out.

DynapacParts.com
800-889-0661

Page 26 of 251
 5) The screed bottom should ride on the
straight edge all the way out. If the screed
extension does not ride on the straight
edge, it will be necessary to shim the
screed extension bottom.

DynapacParts.com
800-889-0661

Stud that holds the screed plate up

Square head bolt for shimming

DynapacParts.com
800-889-0661

Page 27 of 251
Shimming the Screed Extension To the Slide

DynapacParts.com
800-889-0661

Tip the screed extension bottom whichever way necessary until the screed extension bottom rides on
top of the level as in step 5.

DynapacParts.com
800-889-0661

Page 28 of 251
 DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Set the angle of attack as shown

Page 29 of 251
 DynapacParts.com
800-889-0661

Install the rear support plate as shown in the photo.

DynapacParts.com
800-889-0661

Page 30 of 251
Slope Plate Adjustment

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 31 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 32 of 251
Bolt On Extensions

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 33 of 251
 DynapacParts.com
800-889-0661

See section 18 for more instructions.

DynapacParts.com
800-889-0661

Page 34 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661
7922.7mm
26'-0"
D

2
WIDE PAVE BRACKET

SHT
00
REV
EZIV 10' EXTENDED FULL
2148mm
7ft

12 IN. BOLT ON

24 IN. BOLT ON
C

GREASE FITTING EXPOSED

DWG
NO.
303.4mm
12in

DETAIL WIDEPAVE

2490.3mm
8'-2"
B B

*
7632mm

CARLSON
25ft
A A
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
TITLE

STANDARD EZIV 10' FULLY EXTENDED

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B EZIV 10' FOR TRANSPORT 00 2 OF 2

8 7 6 5 4 3 2 1

800-889-0661 Page 35 of 251

Torque slide as follows

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 36 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661 D

AVAILABLE

1
IN 12" 18" & 24"

SHT
LENGTHS

00
REV
LOWER EXTENSION BERM POSITION
C

TYPICAL BERM CYLINDER

INSTALLATION

DWG
NO.
4" HEIGHT
OF SLOPE
B B

TYPICAL BERM INSTALLATION SHOWING INTENDED RESULT

A
CARLSON an Astec company
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

LOWER EXTENSION
TITLE

BERM POSITION

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661Page 37 of 251
 MAINTENANCE

DynapacParts.com
LUBE CHART

800-889-0661
VIBES, MAIN/EXT
DEPTH SCREWS/ PIVOT POINT
WEEKLY
DAILY
IDLER SPROCKET DAILY
CROWN SCREWS/UPPER SHOWN DAILY
DEPTH SCREWS DAILY
SCREEDARM PIVOT POINT DAILY
CROWN SCREWS/ UPPER SHOWN DAILY
VERTICAL SCREWS DAILY

DynapacParts.com
800-889-0661

Page 38 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.
SPECIFICATIONS:
STANDARD PAVING WIDTH: 10 FT. (3.05M)

D 800-889-0661 EXTENDED PAVING WIDTH

EXTENSION LENGTH
19 FT. (5.79M)

5 FT. RIGHT
4 FT. LEFT
D

1 00
* MAX PAVING WIDTH WITH 25 FT. (7.62M)
BOLT ON EXTENSION

SHT
VERTICAL HEIGHT ADJUSTMENT HYDRAULIC

EXTENSION SLOPE DOWN 8%

REV
1977.2mm MAXIMUM BERM HEIGHT 4 IN. (10.16 CM) ON OUTSIDE EDGE

EZIV 10' FOR TRANSPORT

6'-6"
BERM WIDTH AVAILABLE 12 IN. (30.48 CM)
18 IN. (45.72 CM)
24 IN. (60.96 CM)
POWER CROWN 2-1/2 IN. (6.25 CM) POSITIVE
3/4 IN. (1.9 CM) INVERT
C
WALKWAY WIDTH 20-1/2 IN. (52.07 CM) HINGED
OVEN ELECTRIC STOVE TOP ELEMENT
POWER OUTLETS 120 VOLT@ 6000 WATTS
SCREED WEIGHT 7,500 LBS

DWG
NO.
3367.8mm
11ft

B B

2463.7mm
8'-1"

A
CARLSON
PAVING PRODUCTS, INC.
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE

EZIV 10' RETRACTED, FOR SHIPPING

DynapacParts.com
3073.8mm SIZE DRAWING NUMBER REV SHEET:

10ft B EZIV 10' FOR TRANSPORT 00 1 OF 2

8 7 6 5 4 3 2 1

800-889-0661Page 39 of 251
Mar 7, 2011 - 10:10am CARLSON PAVING PRODUCTS, INC. Page 1

INDENTED BILL OF MATERIAL

Items: EZIV10\1459 Thru EZIV10\1459 All Locations Selected

Activity Codes: Active Items, Forecasted Items, Obsolete Items
1 Levels With No Blow Through
No Selection On Basis Of Effectivity Date No Selection On Basis Of Obsolete Date

Level Seq Component-Item Component-Description Opr UOM Scrap Act Stk B/I Qty On-Hand Qty-Per-Parent

DynapacParts.com
Loc LLC Draw REV P/M Ctl B/F Qty-Allocated Qty-On-Order

====================================================================================================================================
Parent Item: EZIV10\1459 EZIV-1019 BATCH# 900770 Loc: ASY LLC: 1

800-889-0661
DYNAPAC F1000
1 5 201-998-003 EZIV 10' BASE MACHINE 0 EA .0 A Y N 1.000000
FLAT TAIL NO GEN. ASY 2 M Y Y

1 10 202-561-100 ELEMENT GP. (W/CONN) 0 EA .0 A Y N 1.000000

ASY 3 M Y Y

1 15 201-732-000 FAB KIT - DYNAPAC F1000 0 EA .0 A Y N 1.000000

EZIV-10' ASY 2 M Y Y

1 20 201-990-000 PLATE AS. - SCREED (STR) (RH) 0 EA .0 A Y N 1.000000

EZIV-10 ASY 3 M Y Y

1 25 201-991-000 PLATE AS. - SCREED (STR) (LH) 0 EA .0 A Y N 1.000000

EZIV-10 ASY 3 M Y Y

1 30 202-559-000 16" DEPTH SCREW GP. (RH) STD. 0 EA .0 A Y N 1.000000

ASY 3 M Y Y

1 35 202-991-000 ENDGATE GP. - STANDARD (HWE) 0 EA .0 A Y N 1.000000

EZIV ASY 3 M Y Y

1 40 1044-0145 THERMOSTAT AS. 0 EA .0 A Y N 1.000000

(330°F) ASY 4 M Y Y

1 45 1030-0025 MANIFOLD - LOAD SENSE 24V 0 EA .0 A Y N 1.000000

EATON# X630AA00655A ASY 2 P Y Y

1 50 4200-0011 KIT - JACK (SIDE) 0 EA .0 A Y N 1.000000

ENCLOSED SPRING ASY 3 M Y Y

1 55 305-501-000 ELECTRICAL GP. - DC 0 EA .0 A Y N 1.000000

DYNAPAC W\ MOBA (F1000) ASY 2 M Y Y

1 60 305-965-000 AC ELECTRICAL GP. 0 EA .0 A Y N 1.000000

24 VOLT DC - DYNAPAC ASY 2 M Y Y

DynapacParts.com
800-889-0661

Page 40 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-703-000 PLATE GP - SCREED (FLAT TAIL) 1

800-889-0661
00 INITIAL RELEASE 3/2/2006 KAC 2 201-968-200 FRAME GP - GENERIC LH 1
01 ITEM #2 201-968-200 WAS 201-968-100, ITEM #3 201-968-201 WAS 201-968-101 8/18/2006 KAC 3 201-968-201 FRAME GP - GENERIC RH 1
5179 02 ITEM#8 200-871-200 WAS 200-871-000 3/28/2007 RJM 4 202-730-200 EXTENSION GP - LH 1
D D
ITEM #9 200-255-000 WAS REPLACED WITH 202-960-000, ITEM #10 200-348-000 WAS 5 202-731-200 EXTENSION GP - RH 1
5547 03 10/21/2008 RJM
REPLACED WITH 202-962-000
6 201-154-000 COVER GP - 10' EZIV 1
ITEM#6 201-154-000 WAS REPLACED WITH 202-985-000, ITEM#8 200-871-200 WAS
5964 04 02/15/2010 RJM

1
REPLACED WITH 202-986-000 7 201-153-000 CROWN GP, EZIV 1

SHT
ITEM #4 202-730-000 WAS REPLACED WITH 202-730-200, ITEM #5 202-731-000 WAS 8 202-986-000 WALKWAY GP - EZIV-10 1
6058 05 REPLACED WITH 202-731-200 6/26/2010 KSB
9 202-960-000 HYDRAULIC AS. - CYLINDER (RH) 1

06
6099 06 ITEM #6 202-985-000 WAS REPLACED WITH 201-154-000 8/06/2010 RJM
10 202-962-000 HYDRAULIC AS. - CYLINDER (LH) 1

REV
11 202-692-000 DECAL GP - EZIV-10 1
12 202-770-000 GENERATOR ELEC BOX MOUNT GROUP 1

201-998-003
12
05
C 4

10 2 05
5

DWG
NO.
6 3

9
11

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN KAC 3/1/2006
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED X 3/2/2006
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EZ IV 10' BASE MACHINE (FLAT TAIL) NO GEN
DESIGN KAC 3/1/2006
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
8 7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER X 3/2/2006

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 3735.60
.XX
.XXX =
= 0.03
0.01 FINISH =
125 SEE BOM B 201-998-003 06 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 41 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION ITEM NO. PART NUMBER DESCRIPTION QTY.
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED 1 201-968-202 FRAME WD - LH 1
ECN REV. DESCRIPTION DATE DRAWN ENG 2 200-713-000 PRE-STRIKE OFF AS. - LH 1

800-889-0661
00 INITIAL RELEASE 11-17-05 RES 3 200-422-000 MOUNT WD - CYLINDER 1
5093 01 REPACED ELEMENT AS. WITH NEW AS. 11-08-06 JAM 4 200-797-000 MOTOR AS. - VIBE 1
5197 02 ITEM#41 4201-0104 WAS 4201-0102 4-11-07 RJM 5 200-001-000 ROD - THREADED 8
D 5235 03 ADDED END CAP 1020-0191 06-06-07 MP 6 200-096-000 BAR STOCK 17 D
5313 04 DEELTED 1020-2713, 1048-3350, 1048-3145, 1048-0950, 1048-3325, 1048-3115 10-23-07 AAH 7 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 4
5347 05 ITEM#33 200-918-000 IS NOW 1008-0200, ITEM#34 202-740-225 IS NOW 202-740-222 02/01/2008 ASH
8 1048-3040 WASHER - 1/2" USS 2

1
9 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 2
5441 06 PART NUMBER #4201-0104 HAS BEEN REMOVED FROM BOM 07-02-08 RJM

SHT
10 1006-0126 PLATE 1
6124 07 CHANGED FRONT CLAMP BAR ASSY, REMOVED (1) 202-740-222, ADDED (1) 202-740-322 9/15/2010 KSB
11 1048-1130 BOLT - HEX - 3/8 - 16 * 1 1/4" 1

07+
12 1048-1260 BOLT - HEX - 1/2-13 * 2" 2

REV
13 1048-3370 WASHER - LOCK - 1/2" 6
14 1048-3050 WASHER - FLAT - 1/2" USS 6
15 1048-1315 BOLT - HEX - 1/2-13 * 4 1/2" 4
16 1048-3220 WASHER - FLAT - 1/2" SAE 8
17 1048-9275 BOLT 1

201-968-200
18 1048-2300 NUT- LOCK - 3/4-10 1
19 1046-5930 PLUG - HEX 1
20 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
C
21 200-028-000 PLATE 1
22 202-615-000 PLATE 1
23 1048-1200 BOLT - HEX - 1/2-13 * 3/4" 2
24 1048-2390 NUT - JAM - 1/2-13 2
25 1048-3240 WASHER - FLAT - 3/4" SAE 1
26 1048-2070 NUT - HEX - 1/2"-13 4

DWG
NO.
27 1048-3360 WASHER - LOCK 8
28 1048-1890 SCREW 4
29 1048-3270 WASHER - FLAT - #10 NEOPRENE 4
30 1048-3130 WASHER - FLAT - 5/16" SAE 4
31 200-877-000 PLATE 1
32 201-968-108 CRANK LEVER AS, DEPTH SCREW 1
33 1008-0200 CHAIN AS. - EZIII REAR GRATE 1
34 1020-0191 CAP - END 1
B
35 202-740-322 ELEMENT HOLD-DOWN AS.- (LH) 1
36 202-740-222 ELEMENT HOLD-DOWN AS.- MAIN SCREED 2

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RES 11/17/2005
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
RES 11/17/2005
FRAME GP - GENERIC LH
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER EZIV-10'

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 201-968-200 07+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 42 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

800-889-0661
19

D D
10 28 30 29

2
32 11
34

SHT
07+
REV
12 13 14 2X
8 9

201-968-200
24 7
C 23 13 14 2X
1

33
2

DWG
NO.
31 22 7 14 13 2X
5
17 18 25
21
4
3

B 15 27 16 16 26 4X B

6 17X

35

36

A
2X
CARLSON
PAVING PRODUCTS, INC.
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE FRAME GP - GENERIC LH

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 201-968-200 07+ 2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 43 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
REV1: VIBE MOTOR HAS BEEN REPLACED BY 1047-0630. WAD 1-9-03 1 1 200-796-000 02 BAR STOCK
REV2: ADDED BEARING SPACER TO ASSEMBLY. DWN 08/31/04 2 1 200-795-000 00 VIBE WD - HOUSING
D 3 1 1047-0630 00 MOTOR - HYDRAULIC
D

800-889-0661
4 1 200-794-000 01 PLATE
5 2 1049-3200 BEARING
6 1 200-842-000 00 TUBE
7 3 1048-1115 BOLT - HEX - 3/8 - 16 * 1"
8 1 1048-0920 BOLT - HEX - 1/4-20 * 3/4"
9 1 1048-2590 NUT - JAM - 1"-12 NYLOCK
10 1 1048-3280 WASHER - FENDER - 1/4"
11 1 1048-3325 WASHER - LOCK - 1/4"
12 2 1048-3350 WASHER - LOCK - 3/8"
13 2 1048-3145 WASHER - FLAT - 3/8" SAE
C 14 1 1048-9906 00 KEY STOCK
C
15 1 202-677-000 01 TUBE

7
12
13

B B
2 3

14
1
5
5
4 9
15
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
10 ph (253) 875-8000 fx (253) 846-0100
A A
MOTOR AS. - VIBE
11

DynapacParts.com
CAD GENERATED DRAWING,
EZIV
8 DO NOT MANUALLY UPDATE

APPROVALS DATE
7 DESIGN
DN 06/05/00 SIZE DWG. NO. REV.
A 200-797-000SHEET 02

800-889-0661
DRAFT
SVL 6/05/00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 44 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-187-000 HANDLE WD - CRANK 1

800-889-0661
00 INITIAL RELEASE 08-15-05 SMD 2 1006-0121 KNOB 1
6101 01 REPLACED TWO #1048-1170 BOLTS WITH #1048-1587 08-11-2010 RJM 3 1010-7206 COUPLING 1
4 1048-1170 BOLT - HEX - 3/8-16 * 2 1/4" 2
D D
5 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 4
6 1010-7203 TUBE 2

1
7 1049-2100 SEAL - GREASE 2

SHT
8 1049-3150 BEARING 2
9 1010-7202 BAR STOCK 1

01+
10 1048-2590 NUT - JAM - 1"-12 NYLOCK 1

REV
11 1048-1587 BOLT - HEX - 3/8-16 * 2 1/2" 2

11
6 3

201-968-108
11

DWG
9

NO.
6

10
8
B

4 1 5

A
2
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

SMD
DATE

7/19/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN SMD 7/19/2005
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 CRANK LEVER AS, DEPTH SCREW
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
NOTES: .X
.XX
=
=
0.10
0.03
ANGULAR =
.25
0 30'
SEE BOM B 201-968-108 01+ 1 OF 1
.XXX = 0.01 FINISH =

8 7 6 5 4 3 2 1

800-889-0661 Page 45 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG

800-889-0661
00 INITIAL RELEASE 07-19-05 SMD
1 1008-0102 CHAIN AS. 1.1 FT
2 1008-0117 SHUNT - COLD 1
3 1008-0103 CONNECTOR 1
D 4 1008-0125 HOOK 1 D
2

1
SHT
00+
REV
4

1008-0200
C

DWG
NO.
B

SQUEEZ END
CLOSED
1

NOTES:
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

SMD
DATE

7/17/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN SMD 7/17/2005
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 CHAIN AS. - EZIII REAR GRATE
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 1008-0200 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 46 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 202-740-320 ELEMENT HOLDDOWN WD.- (LH) 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1048-1345 BOLT - HEX 1/2-13 * 3" FULL THREAD 1

800-889-0661
6124 00 INITIAL RELEASE 9/15/2010 KSB
3 1048-0592 SCREW, BUTTON 2
4 1048-3050 WASHER - FLAT - 1/2" USS 2
D 5 1048-2400 NUT - JAM - 1/2-13 5 D

6 1048-2402 NUT - WELD - 1/2-13 3

7 1048-2415 NUT - ACORN - 1/2"-13 2

1
SHT
00+
REV
202-740-322
C

203-119-200 ELEMENT

DWG
NO.
SHOWN FOR REF. ONLY

B
2
5
6

2x 4 3 5 6 7

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RES 11/13/2005
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED 12/30/2004
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ELEMENT HOLD-DOWN AS.- (LH)
DESIGN RES 11/13/2005
5. DO NOT SCALE DRAWING MAIN SCREED (10")
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 12/30/2004

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-740-322 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 47 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ELEMENT HOLDDOWN WD.- MAIN SCREED
1 202-740-220 1
ECN REV. DESCRIPTION DATE DRAWN ENG
(10")
2 1048-1345 BOLT - HEX 1/2-13 * 3" FULL THREAD 1

800-889-0661
00 INITIAL RELEASE 11/28/2005 RES
3 1048-0592 SCREW, BUTTON 2
5106 01 1048-1345 WAS 1048-1281 11/17/2006 KAC
4 1048-3050 WASHER - FLAT - 1/2" USS 2
D 5 1048-2400 NUT - JAM - 1/2-13 5 D

6 1048-2402 NUT - WELD - 1/2-13 3

7 1048-2415 NUT - ACORN - 1/2"-13 2

1
SHT
01
REV
202-740-222
C

203-119-200 ELEMENT

DWG
NO.
SHOWN FOR REF. ONLY

B
2
5
6

2x 4 3 5 6 7

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

RES
DATE

11/15/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED 1/1/2005

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN RES 11/15/2005 ELEMENT HOLD-DOWN AS.- MAIN SCREED
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 1/1/2005 10'

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-740-222 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 48 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION ITEM NO. PART NUMBER DESCRIPTION QTY.
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED 1 201-968-203 FRAME WD - RH 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 200-712-000 PRE-STRIKE AS. - RH 1

800-889-0661
3 200-797-000 MOTOR AS. - VIBE 1
00 INITIAL RELEASE 11-15-05 RES
4 200-169-000 MOUNT WD. - TRUNNION 1
01 REPLACED 200-517-000 W/ 200-517-200 04-28-06 RES
* 5 202-614-000 GAUGE AS. - TEMPERATURE 1
5091 02 REMOVED OVEN & HARDWARE 11-07-06 JAM
6 200-001-000 ROD - THREADED 8
D 5093 03 REPLACED ELEMENT AS. WITH NEW AS. 11-08-06 JAM D
7 200-096-000 BAR STOCK 17
5197 04 ITEM#40 4201-0104 WAS 4201-0102 4-11-07 RJM 8 200-028-000 PLATE 1
5219 05 ADDED OVEN AS. AND HARD WARE FOR ELECTRIC BOX MOUNT PLATE 05-10-07 MSOU 9 202-615-000 PLATE 1

1
5235 06 ADDED END CAP 1020-0191 06-06-07 MP 10 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 4

SHT
5347 07 ITEM#38 200-918-000 IS NOW 1008-0200, ITEM#39 202-740-225 IS NOW 202-740-222 02-04-07 ASH
11 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 2
12 1048-3040 WASHER - 1/2" USS 2

10+
5441 08 PART NUMBER #4201-0104 HAS BEEN REMOVED FROM BOM 07-02-08 RJM
13 1006-0126 PLATE 1

REV
5994 09 UPDATED VIBE MOTOR POSITION 04-05-2010 RJM
14 1048-1130 BOLT - HEX - 3/8 - 16 * 1 1/4" 1
6124 10 CHANGED FRONT CLAMP BAR AS. REMOVED (1) 202-740-222, ADDED (1) 202-740-422 9/15/2010 KSB 15 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
16 1048-1260 BOLT - HEX - 1/2-13 * 2" 2
17 1048-3370 WASHER - LOCK - 1/2" 6
18 1048-3050 WASHER - FLAT - 1/2" USS 6
19 1048-1315 BOLT - HEX - 1/2-13 * 4 1/2" 4

201-968-201
20 1048-3160 WASHER 8
21 1048-3360 WASHER - LOCK 4
22 1048-2070 NUT - HEX - 1/2"-13 4
C
23 1048-1044 BOLT - HEX - 1/4-20 * 2 1/4" 2
24 1048-3020 WASHER - FLAT - 1/4" USS (HEAVY) 4
25 1048-2027 NUT - HEX - 1/4"-20 NYLOCK 2
26 1048-1200 BOLT - HEX - 1/2-13 * 3/4" 2
27 1048-2390 NUT - JAM - 1/2-13 2
28 1046-5930 PLUG - HEX 1

DWG
29 1048-1890 SCREW 4

NO.
30 1048-3270 WASHER - FLAT - #10 NEOPRENE 4
31 1048-3130 WASHER - FLAT - 5/16" SAE 4
32 200-875-000 PLATE 1
33 200-517-200 PLATE 1
34 1048-1120 BOLT - HEX - 3/8-16 * 1" 2
35 1048-3140 WASHER - FLAT 2
36 1048-3350 WASHER - LOCK - 3/8" 2
37 201-968-108 CRANK LEVER AS, DEPTH SCREW 1
B 38 1008-0200 CHAIN AS. - EZIII REAR GRATE 1
39 202-740-222 ELEMENT HOLD-DOWN AS.- MAIN SCREED 2
40 1048-3115 WASHER - FLAT - 1/4" SAE 4
41 1048-3325 WASHER - LOCK - 1/4" 4
42 1048-0920 BOLT - HEX - 1/4-20 * 3/4" 4
* 43 200-366-000 OVEN AS. 1
44 1020-0191 CAP - END 1
45 202-740-422 ELEMENT HOLD-DOWN AS.- (RH) 1

NOTE: THESE ITEMS NOT REQUIRED ON VOGELE 5200 (SEE FAB KIT).

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RES 4/26/2006
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE FRAME GP - GENERIC RH
DESIGN RES 11/12/2005
5. DO NOT SCALE DRAWING EZIV-10'
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 818.28
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 SEE BOM B 201-968-201 10+ 1 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 49 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661 14
D

2
13
4 15

SHT
24 24 23 27 2X

10+
19 20 20 21 22 4X

REV
2X 35 36 34 44
A

201-968-201
31 30 29
33
C

37
40 41 42

18 17 16

DWG
NO.
3 28
2
6

1
32

B B

12 11
9
39
43
7
27
17 X DETAIL A
10 31 SCALE 1 : 5

CARLSON
45
A 5 26 17 18 2X A
PAVING PRODUCTS, INC.
38 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
TITLE FRAME GP - GENERIC RH
10 17 18 2X
8

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

39 B 201-968-201 10+ 2 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 50 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-883-004 BAR STOCK - HEAT BLOCK 1

800-889-0661
00 INITIAL RELEASE 10-14-03 WRS 2 201-883-003 PLATE 1
5825 01 202-611-000 WAS REPLACED WITH 203-629-000 08-05-09 RJM 3 1048-1210 BOLT - HEX - 1/2 - 13 * 1" 2
4 1048-3150 WASHER 4
D D
5 1048-3360 WASHER - LOCK 4
6 1048-1230 BOLT - HEX - 1/2-13 * 1 1/4" 2
7 202-613-000 ADAPTER 1

1
8 203-629-000 GAUGE - TEMPERATURE 1

SHT
9 1048-9390 SCREW 2

01
10 1048-3510 WASHER - INT STAR - #4 2

REV
8

202-614-000
C

DWG
3

NO.
5

CARLSON
UNLESS OTHERWISE SPECIFIED
10
APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN WRS 10-14-03
9 2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE GAUGE AS. - TEMPERATURE
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 5.16
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-614-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 51 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 202-740-420 ELEMENT HOLDDOWN WD.- (RH) 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1048-1345 BOLT - HEX 1/2-13 * 3" FULL THREAD 1

800-889-0661
6124 00 INITIAL RELEASE 9/15/2010 KSB
3 1048-0592 SCREW, BUTTON 2
4 1048-3050 WASHER - FLAT - 1/2" USS 2
D 5 1048-2400 NUT - JAM - 1/2-13 5 D

6 1048-2402 NUT - WELD - 1/2-13 3

7 1048-2415 NUT - ACORN - 1/2"-13 2

1
SHT
00+
REV
202-740-422
C

203-119-200 ELEMENT
SHOWN FOR REF. ONLY
2

DWG
NO.
5

B 7 5 3 6 5 4

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RES 11/13/2005
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED 12/30/2004
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ELEMENT HOLD-DOWN AS.- (RH)
DESIGN RES 11/13/2005
5. DO NOT SCALE DRAWING MAIN SCREED (10')
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 12/30/2004

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-740-422 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 52 of 251

 8 7 6 5 4 3 2 1
NOTES: OVEN HOUSING ASSEMBLY WITH SLIDE IS ONE PART. # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-228-000 01 OVEN WD
2 1 300-013-000 ELEMENT AS. - OVEN
D 3 1 1048-1584 BOLT - HEX
D

800-889-0661
4 4 1048-1872 SCREW - ROUND
5 4 1048-2010 NUT- HEX - #10-32
6 4 1048-3100 WASHER - FLAT - #10 SAE
7 4 1048-3520 WASHER - EXT STAR - #10
8 8 1 200-770-000 02 PLATE
9 1 1048-3215 WASHER - FENDER - 5/16" ID X 2" OD
10 1 1048-3120 WASHER

3
C C
10

B 1 B

5 7 6 4
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE OVEN AS.

DynapacParts.com
APPROVALS DATE
EZIV-10
DESIGN
WRS 02-16-04
MODEL
WRS 02-16-04 SIZE DWG. NO. REV.
A 200-366-000 02

800-889-0661
DRAFT
WRS 02-16-04 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 53 of 251 1-1
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
PARTS LIST
ECN REV. DESCRIPTION DATE DRAWN ENG ITEM NO. PART NUMBER DESCRIPTION QTY
6058 00 INITIAL RELEASE 6/24/2010 KSB KAC 1 200-072-100 UPPER WD - BODY (LH) 1

800-889-0661
2 202-730-100 LOWER AS. - LH 1
3 201-122-000 SCREW AS. - VERTICAL 2
4 201-339-000 TUBE WD - SLIDE (VERTICAL) 2
D D
5 200-961-000 CHAIN AS. - ROLLER (30 1/2 IN) 1
6 200-960-000 CHAIN AS. - ROLLER (27 IN) 1

1
7 200-721-000 ARM WD - AOA (LH) 1

SHT
8 200-420-000 HOUSING WD - VERTICAL (TUBE) 2
9 200-370-001 PLATE 1

00+
PARTS LIST
10 200-339-000 PLATE 1

REV
ITEM NO. PART NUMBER DESCRIPTION QTY
11 200-016-000 SPROCKET 1
41 200-360-000 STUD 2
12 200-598-000 MOTOR - VIBE 1
42 200-343-000 ROD END 4
13 200-323-000 BEARING 2
43 1048-1245 BOLT - HEX - 1/2-13 * 1 1/2" 6
14 200-344-000 MOTOR - HYDRAULIC 1
44 200-233-000 PLATE 1
15 4204-0171 BAR STOCK 1

202-730-200
45 201-921-000 PLATE 1
16 200-724-000 BAR STOCK 1
46 1048-3401 BOLT - HEX - 3/8-16 * 3/4" 4
17 200-392-000 RING - SNAP 2
47 1048-3140 WASHER - FLAT 4
C 18 200-718-000 PLATE 2
48 1048-3350 WASHER - LOCK - 3/8" 4
19 200-359-000 BAR STOCK 1
49 4204-0173 NUT - HEX 1
20 4204-0172 CLEVIS 1
50 1048-9005 PIN - ROLL 1
21 200-103-000 PLATE 1
51 200-345-000 SPROCKET - MOTOR VERTICAL 1
22 4213-0118 SPROCKET 2
52 4201-0104 GAUGE 1
23 1048-3370 WASHER - LOCK - 1/2" 9

DWG
53 1048-3060 WASHER - FLAT - 3/4" USS (HEAVY) 2

NO.
24 1048-3220 WASHER - FLAT - 1/2" SAE 40
54 1048-3240 WASHER - FLAT - 3/4" SAE 2
25 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 9
55 2000-1810 HOSE AS. 1
26 1048-3360 WASHER - LOCK 29
56 2000-1809 HOSE AS. 1
27 1048-1230 BOLT - HEX - 1/2-13 * 1 1/4" 15
57 201-428-000 PLATE 2
28 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 4
58 200-875-000 PLATE 1
29 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2
59 200-886-000 CAP WD - TUBE (VERTICAL) 2
30 1048-1250 BOLT- HEX - 1/2-13 * 1 3/4" 3
60 202-827-000 SHIM - BODY 3/16" EZ IV; DBL SLOT 1
B 31 1048-9015 PIN - CLEVIS 1
61 202-828-000 SHIM - BODY 3/16" EZ IV; SNGL SLOT 2
32 1048-9035 KEY - COTTER 1
62 1046-0800 FITTING - HYDRAULIC 2
33 1048-4162 BOLT - SQHSS - 5/8 - 11 *2" 2
63 1049-1030 FITTING - GREASE (STR) 2
34 1048-1280 BOLT- HEX - 1/2 - 13 * 2 1/2" 1
64 300-700-100 JUNCTION BOX AS. 1
35 1048-7215 BOLT - SHCS - 1/2 - 13 * 1 1/2" 2
65 1048-3090 WASHER - FLAT - #10 SAE 4
36 1048-1660 BOLT - HEX - 3/4 - 10 * 6" 2
66 1048-3310 WASHER - LOCK 4
37 1048-2560 NUT - JAM - 3/4"-10 NYLOCK 2
67 1048-6995 BOLT - BUTTON HEAD - 10-32 X .5" 4
38 1048-9263 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/4" 1
39 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4
40 1048-0920 BOLT - HEX - 1/4-20 * 3/4" 1

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN KSB 6/24/2010
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 6/24/2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EXTENSION GP - LH
DESIGN KSB 6/24/2010
5. DO NOT SCALE DRAWING EZIV-10'
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 6/24/2010

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 397.71
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 202-730-200 00+ 1 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 54 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

800-889-0661
1 57 61
55 56 63

D 46 47 57 61 D
48 45
62

2
24

SHT
00+
26

REV
58 60
43

39

202-730-200
24
26 11

27
C
29 18 39 26
26
24 24
43
10
7 38
44
28 33
42 30 24

DWG
NO.
24 9 26
24
24 26 24
43
23 28 26
41 40
28 39
29 33 15
25 24 42
B B
27 26
2
32

16
31
20

49
19

50

A
CARLSON
PAVING PRODUCTS, INC.
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE EXTENSION GP - LH
EZIV-10'

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 202-730-200 00+ 2 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 55 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661 1
D

3
SHT
39
52

00+
REV
12

24 64

202-730-200
26
6 5
34
C

67 66 65
22

DWG
NO.
51
3
22

27

26 59
37
B B
24 13

17
21
27

14 26

24
8
26

CARLSON
35 4
A A
PAVING PRODUCTS, INC.
53 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
TITLE EXTENSION GP - LH
54 EZIV-10'

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:
36
B 202-730-200 00+ 3 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 56 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-121-000 00 HOUSING AS. - BEARING
2 1 200-807-000 01 NUT WD - VERTICAL
D 3 1 200-065-000 00 BAR STOCK
D

800-889-0661
4 4 1048-3360 WASHER - LOCK
5 1 1048-2590 NUT - JAM - 1"-12 NYLOCK
6 4 1048-1210 BOLT - HEX - 1/2 - 13 * 1"
7 1 1048-9904 00 KEY STOCK

C C

6 7 3
B B
4

5 CARLSON PAVING PRODUCTS INC.

1 18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
SCREW AS. - VERTICAL

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE

APPROVALS DATE
DESIGN
SAS 02-12-03 SIZE DWG. NO. REV.
A 201-122-000SHEET 00

800-889-0661
DRAFT
RM 05-20-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 57 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-067-000 00 HOUSING WD - BEARING
2 2 1049-3150 BEARING
D 3 2 1049-2100 SEAL - GREASE
D

800-889-0661
4 4 1048-1115 BOLT - HEX - 3/8 - 16 * 1"
5 1 1010-7203 00 TUBE
6 1 1046-5930 PLUG - HEX

5
2

C C
1

B
4 B

3
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
HOUSING AS. - BEARING

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE

APPROVALS DATE
DESIGN
WAD 09-21-04 SIZE DWG. NO. REV.
A 201-121-000SHEET 00

800-889-0661
DRAFT
WAD 09-21-04 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 58 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 300-060-901 JUNCTION BOX W/ HOLES INSTALLED 1

800-889-0661
6058 00 INITIAL RELEASE 6/24/2010 KSB KAC 2 1042-0383 CONNECTOR - CORD RANGE .250 - .375 1
REPLACED #1042-0142 WITH #1042-0383, REPLACED #1042-0162 WITH #138409-04
6095 01 ADDED #1047-0499 AND #1047-0500 8/3/2010 KSB KAC 3 1042-0152 CONNECTOR, WATERTIGHT 3/4" 2
6367 02 1042-8003 WAS 1042-8093 09-21-11 TH KAC 4 138409-04 HOLE PLUG - SNAP BUTON (7/8") 8
D D
5 1042-0184 NUT - LOCK 1/2" (PIPE) 1
11 10 8
6 1042-0185 NUT - LOCK 3/4" 2
7 1042-8003 TERMINAL BLOCK - 6 POST 1

1
8 1048-3090 WASHER - FLAT - #10 SAE 4

SHT
7 9 1048-1830 BOLT - PAN HD PHILLIPS - 10 - 32 * 3/4" 2

02
10 1048-3520 WASHER - EXT STAR - #10 2

REV
11 1048-2010 NUT- HEX - #10-32 2
6 14 12 1047-0499 SEAL - RING 3/4" 2
01 13 1047-0500 SEAL - RING 1/2" 1
14 1042-0188 3/4" PLASTIC BUSHING 2
14 6 15 1042-0187 1/2" PLASTIC BUSHING 1
01

300-700-100
5 15
01
C

DWG
NO.
1

3 12

12 3

4
01

9 8
CARLSON
UNLESS OTHERWISE SPECIFIED
2 13 APPROVALS DATE
A
01 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN KSB 6/23/2010
A
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 6/23/2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JUNCTION BOX AS.
5. DO NOT SCALE DRAWING
DESIGN KSB 6/23/2010
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 6/23/2010
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 2.88
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 300-700-100 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING
INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A
PARTS LIST
LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON
PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-896-100 UPPER WD - BODY (RH) 1

800-889-0661
6058 00 INITIAL RELEASE 6/24/2010 KSB KAC 2 202-731-100 LOWER BODY 1
3 200-103-000 PLATE 1
4 200-339-000 PLATE 2
D D
5 200-016-000 SPROCKET 2
6 200-323-000 BEARING 2
7 200-344-000 MOTOR - HYDRAULIC 1

1
8 4204-0171 BAR STOCK 1

SHT
9 200-724-000 BAR STOCK 1

00+
10 200-392-000 RING - SNAP 2

REV
11 200-717-000 ARM WD - AOA (RH) 1
PARTS LIST 12 200-718-000 PLATE 2
ITEM NO. PART NUMBER DESCRIPTION QTY 13 4204-0172 CLEVIS 1
43 1048-3350 WASHER - LOCK - 3/8" 4 14 200-359-000 BAR STOCK 1
44 1048-3140 WASHER - FLAT 4 15 4213-0118 SPROCKET 2

202-731-200
45 200-199-001 PLATE 1 16 1048-1280 BOLT- HEX - 1/2 - 13 * 2 1/2" 1
46 4204-0173 NUT - HEX 1 17 1048-3360 WASHER - LOCK 35
C 47 1048-9005 PIN - ROLL 1 18 1048-1250 BOLT- HEX - 1/2-13 * 1 3/4" 3
48 201-122-000 SCREW AS. - VERTICAL 2 19 1048-1245 BOLT - HEX - 1/2-13 * 1 1/2" 10
49 200-345-000 SPROCKET - MOTOR VERTICAL 1 20 1048-3220 WASHER - FLAT - 1/2" SAE 46
50 200-598-000 MOTOR - VIBE 1 21 1048-7210 BOLT - SHCS - 1/2 - 13 * 1 1/4" 2
51 1048-0920 BOLT - HEX - 1/4-20 * 3/4" 1 22 1048-1230 BOLT - HEX - 1/2-13 * 1 1/4" 17
52 1048-3240 WASHER - FLAT - 3/4" SAE 2 23 1048-9263 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/4" 2

DWG
NO.
53 1048-3060 WASHER - FLAT - 3/4" USS (HEAVY) 2 24 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 5
54 4201-0104 GAUGE 1 25 1048-1660 BOLT - HEX - 3/4 - 10 * 6" 2
55 2000-1811 HOSE AS. 1 26 1048-2560 NUT - JAM - 3/4"-10 NYLOCK 2
56 2000-1813 HOSE AS. 1 27 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 4
57 201-428-000 PLATE 5 28 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2
58 200-886-000 CAP WD - TUBE (VERTICAL) 2 29 1048-4162 BOLT - SQHSS - 5/8 - 11 *2" 2
59 202-828-000 SHIM - BODY 3/16" EZ IV; SNGL SLOT 5
30 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 9
B 60 1046-0800 FITTING - HYDRAULIC 2
31 1048-3370 WASHER - LOCK - 1/2" 9
61 1049-1030 FITTING - GREASE (STR) 2
32 1048-9015 PIN - CLEVIS 1
62 300-700-100 JUNCTION BOX AS. 1
33 1048-9035 KEY - COTTER 1
63 1048-3090 WASHER - FLAT - #10 SAE 4
34 200-343-000 ROD END 4
64 1048-3310 WASHER - LOCK 4
35 200-360-000 STUD 2
65 1048-6995 BOLT - BUTTON HEAD - 10-32 X .5" 4
36 200-962-000 CHAIN AS. - ROLLER (39 1/2 IN) 1
37 200-963-000 CHAIN AS. - ROLLER (37 IN) 1
38 200-233-000 PLATE 1
39 200-420-000 HOUSING WD - VERTICAL (TUBE) 2
40 201-339-000 TUBE WD - SLIDE (VERTICAL) 2
41 201-921-000 PLATE 1
42 1048-3401 BOLT - HEX - 3/8-16 * 3/4" 4

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN KSB 6/24/2010
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 6/24/2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EXTENSION GP - RH
DESIGN KSB 6/24/2010
5. DO NOT SCALE DRAWING EZIV-10'
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 6/24/2010

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 546.46
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 202-731-200 00+ 1 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 60 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED 54
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING 1
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661 38 D

2
62
63 64 65

SHT
00+
61

REV
9

23
8 60

202-731-200
4
33 2
C 47
13 32
46 11 51
22 17 20
20 31 30 14

24 5 22 17 20

DWG
NO.
45
28 17 27 41
29
20 20 18
12
24
B B

27
29
35
27 17 28

34
44 43 42
34
35

22 17 20
34

A
CARLSON
PAVING PRODUCTS, INC.
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE EXTENSION GP - RH
EZIV-10'

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 202-731-200 00+ 2 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 61 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED

1
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D
55
56

54
800-889-0661
19 17 20
57 59 D

3
SHT
00+
45

REV
36

202-731-200
15
C

48
2
37
22 49

DWG
NO.
17 15 26 24

20 50
48 58 6
B
20
3
B
10
7 22 17
16
18
17
17
20
21
40 39

A 53 CARLSON
PAVING PRODUCTS, INC.
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

52 TITLE EXTENSION GP - RH
EZIV-10'
25

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 202-731-200 00+ 3 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 62 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG
1 201-145-000 COVER WD - REAR (RH) 1

800-889-0661
00 INITIAL RELEASE 06/10/03 RM
2 201-147-000 COVER WD - REAR (LH) 1
01 REMOVED 1020-0226, 1048-1115, AND 1048-3350. 09/26/03 WAD
3 201-148-101 PLATE 1
02 ADDED WASHER 1048-3100 12X 5/16/2006 PGM
D
4 1020-0139 GUARD, EZIV 1 D
5405 03 DELETED 201-144-000 & 201-146-000, ITEMS 6, 7 & 8 QTY WAS 20 5/21/2008 THH
5 200-523-000 COVER LATCH AS. 6
5552 04 CHANGED CROWN ASSY COVER TO ACCOMODATE NEW TURNBUCKLE PLATES 10/29/2008 KSB
6 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 14

1
7 1048-3050 WASHER - FLAT - 1/2" USS 14

SHT
4 8 1048-3370 WASHER - LOCK - 1/2" 14
9 1048-2010 NUT- HEX - #10-32 12

04
10 1048-3520 WASHER - EXT STAR - #10 12

REV
11 1048-1850 BOLT- PAN HD PHILLIPS - 10 - 32 * 1 1/4" 12
3
12 1048-3100 WASHER - FLAT - #10 SAE 12

6X 5

201-154-000
C
12X 9 10 12 11

DWG
NO.
20X 7 8 6

NOTE: FOR REV 03, THE TOP COVERS ARE IN THE FAB KITS.

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

RM
DATE

6/8/2003
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN RAJ 1/26/2003
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 COVER GP - 10' EZIV
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 201-154-000 04 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 63 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1040-0005 BUCKLE WD - TURN (UPPER) 1

800-889-0661
01 ADDED ALTERNATE POSITION FOR EZIV 8' 6/9/2006 PGM 2 1040-0006 BUCKLE AS. - TURN (LOWER) 1
02 ADDED ITEM #33(1040-0121) AND ITEM #34(1048-1900) 9/5/2006 KAC 3 1049-8020 COLLAR - 2" SPLIT COLLAR 5
5179 03 ITEM#33 200-367-000 WAS 1041-0121, ITEM#34 QTY WAS 4 IS NOW 2 4/5/2007 RJM 4 1040-0122 BAR STOCK 2
D D
5552 04 CHANGED TURNBUCKLE PLATES FROM (2) PIECES TO (1) PIECE 10/28/2008 KSB 5 1040-0123 BAR STOCK 2
5689 05 CHANGED DECAL, CHANGED SLOT WIDTH, UPDATED HARDWARE 3/25/2009 KSB 6 201-141-000 PLATE 1

1
6090 06 ADDED CROWN LOCKING STRAPS 7/29/2010 KSB KAC 7 1047-0915 MOTOR - HYDRAULIC 1

SHT
8 1040-0117 BUSHING 2
9 1049-5130 SPROCKET 1

06
10 1050-1008 SHIM 8

REV
11 1048-2300 NUT- LOCK - 3/4-10 4
12 1048-1632 BOLT - HEX - 3/4-10 * 3 1/2" 4
13 1048-1230 BOLT - HEX - 1/2-13 * 1 1/4" 4
14 1048-3360 WASHER - LOCK 6
15 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 4

201-153-000
16 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2
17 1048-2070 NUT - HEX - 1/2"-13 2
C 18 1048-0930 BOLT - HEX - 1/4-20 * 3/4" 1
19 1048-3325 WASHER - LOCK - 1/4" 1
20 1048-3280 WASHER - FENDER - 1/4" 1
21 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 2
22 1048-1250 BOLT- HEX - 1/2-13 * 1 3/4" 2
23 1049-1030 FITTING - GREASE (STR) 4

DWG
NO.
24 1020-7705 SPROCKET 1
25 201-258-000 BAR STOCK 1
26 1048-3401 BOLT - HEX - 3/8-16 * 3/4" 1
27 1048-3355 WASHER - LOCK - 3/8" 1
28 1048-3145 WASHER - FLAT - 3/8" SAE 1
29 201-155-000 CHAIN AS. 1
30 201-156-000 CHAIN AS. 1
B 31 201-143-101 PLATE 1
32 201-142-101 PLATE 1
33 200-367-101 DECAL - POWER CROWN 1
34 201-153-101 PLATE - UPPER LOCKING STRAP 1
35 201-153-102 PLATE - LOWER LOCKING STRAP 1
36 1048-3220 WASHER - FLAT - 1/2" SAE 8
37 1048-1245 BOLT - HEX - 1/2-13 * 1 1/2" 8

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

RAJ
DATE

03-03-03
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CROWN GP, EZIV
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 201-153-000 06 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 64 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

800-889-0661
36
5 06
34
06
37
D 06 D

2
29 32

SHT
3

06
REV
23

201-153-000
18 20 9
21
C

22

DWG
NO.
7

6 14
15
B B
13
24
3
30 16 11
17 14
31 10

3
4
28 27 26
25
8
12 CARLSON
PAVING PRODUCTS, INC.
33 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A 36 A
35 NOMENCLATURE
06 06
37
06 CROWN GP, EZIV
SIZE DRAWING NUMBER REV

B 201-153-000 06

DynapacParts.com
SHEET:
2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 65 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-380-200 GRATE WD - REAR (LH) 1

800-889-0661
5964 00 INITIAL RELEASE 02-15-2010 RJM 2 201-380-100 GRATE WD - REAR (RH) 1
3 202-972-100 WALKWAY WD - SIDE 2
4 1048-9040 KEY - COTTER 8
D D
5 1008-0005 PIN - HINGE 8

1
SHT
00+
REV
5 4

202-986-000
C

DWG
NO.
B
2

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 02-15-2010
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE WALKWAY GP - EZIV-10
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 250.759
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-986-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 66 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-953-000 CYLINDER - HYDRAULIC 1

800-889-0661
5547 00 INITIAL RELEASE 10-21-08 RJM 2 1048-2011 NUT - JAM 1"-14 1
3 202-953-005 CYLINDER ROD END 1

D D

1
SHT
00+
REV
1

202-962-000
C

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 10-21-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE HYDRAULIC AS. - CYLINDER (LH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 59.12
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-962-000 00+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 67 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1

D 800-889-0661 D

2
SHT
00+
REV
202-962-000
C
18.75

DWG
NO.
.44

B 57.06 RETRACTED LENGTH

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 10-21-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE HYDRAULIC AS. - CYLINDER (LH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 59.12
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-962-000 00+ 2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 68 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-955-000 CYLINDER - HYDRAULIC 1

800-889-0661
5547 00 INITIAL RELEASE 10-21-08 RJM 2 1048-2011 NUT - JAM 1"-14 1
3 202-953-005 CYLINDER ROD END 1

D D

1
SHT
3

00+
REV
2

202-960-000
C

DWG
NO.
1

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 10-21-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE HYDRAULIC AS. - CYLINDER (RH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 71.57
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-960-000 00+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 69 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1

D 800-889-0661 D

2
SHT
00+
REV
202-960-000
C .75

DWG
NO.
.44

67.38 RETRACTED LENGTH

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 10-21-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE HYDRAULIC AS. - CYLINDER (RH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 71.57
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 202-960-000 00+ 2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 70 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-143-000 DECAL - CARLSON C 2

800-889-0661
00 INITIAL RELEASE 2 202-595-000 DECAL - CARLSON C 1
5256 01 CHANGE ITEM # 8 QTY WAS 2 07/09/2007 MSOU 3 202-596-000 DECAL - CARLSON 1
5429 02 ADDED ITEM 18 (202-608-100) & ITEM 19 (202-608-200), ADDED SHEET 2 6/13/2008 THH 4 203-144-000 DECAL - US FLAG 2 D
D
5 202-608-000 DECAL - EZIV 1
6 202-598-000 DECAL - WARNING STRIPE 1
7 202-607-000 DECAL - MADE IN USA 2

1
8 202-597-000 DECAL - WARNING STRIPE 1

SHT
9 1095-0270 DECAL - CAUTION (EXTENSION) 1

02
10 1095-0275 DECAL - DO NOT USE DIESEL 2

REV
11 201-821-000 DECAL - CAUTION (TRAILER) 2
12 1095-0155 DECAL - PINCH POINT 2
13 1095-0002 DECAL - 720W MAX LOAD 1
14 1095-0110 DECAL - CAUTION (OVEN) 1
15 202-589-000 DECAL - OVEN SWITCH 1

202-692-000
16 1095-0150 DECAL - 220 VOLTS 1
17 1095-0130 DECAL - CAUTION 2
C 02 18 202-608-100 DECAL - LH EXTENSION SCALE 1
19 202-608-200 DECAL - RH EXTENSION SCALE 1

DWG
NO.
B

NOTES: SEE AUTOCAD DRAWINGS FOR SPECIFICATIONS.

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 11-02-04
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE DECAL GP - EZIV-10
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = B 202-692-000 02 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 71 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

.06
800-889-0661 18 D

2
A

SHT
00
REV
LH EXT DECAL SETUP
LEFT EXTENSION SCALE LAYOUT
C

DETAIL A
SCALE 3 : 8

DWG
NO.
.06
19

B
B B

RIGHT EXTENSION SCALE LAYOUT

DETAIL B
SCALE 3 : 8

A
CARLSON
PAVING PRODUCTS, INC.
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE EXTENSION SCALE LAYOUTS

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 202-692-000 00 2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 72 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-769-000 GENERATOR ELECTRICAL BOX MOUNT 1

800-889-0661
00 INITIAL RELEASE 3/1/2006 KAC 2 1048-3115 WASHER - FLAT - 1/4" SAE 16
6182 01 UPDATED BOM 12/16/2010 RJM 3 1048-2200 NUT - HEX - 1/4"-20 TOPLOCK 4
6195 02 ADDED PART# 201-160-400 TO BOM 1/14/2011 RJM 4 1048-0930 BOLT - HEX - 1/4-20 * 3/4" 4
D D
5 1020-2713 MOUNT 4
6 1048-3145 WASHER - FLAT - 3/8" SAE 4
7 1048-3350 WASHER - LOCK - 3/8" 4

1
8 1048-1130 BOLT - HEX - 3/8 - 16 * 1 1/4" 4

SHT
9 1048-3325 WASHER - LOCK - 1/4" 8

02+
10 1048-0950 BOLT - HEX - 1/4-20 *1" 8

REV
6 7 8
11 201-160-400 MOUNT WD - G-TECH 2

202-770-000
4 2 2 3 4X

DWG
NO.
2 9 10

11

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

KAC
DATE

2/28/2006
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED 2/28/2006

TITLE
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999 DESIGN KAC 3/1/2006
GENERATOR ELEC BOX MOUNT GROUP
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 2/28/2006 USED W/O GENERATOR

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
125 SEE BOM B 202-770-000 02+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 73 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG

800-889-0661
00 INITIAL RELEASE 07-30-05 SMD
1 200-703-101 PLATE WD - SCREED 1
2 200-703-100 STUD AS. - SCREED PLATE 1

D D

1
SHT
2

00
REV
1

200-703-000
C

DWG
NO.
B

NOTES:
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

SMD
DATE

7/29/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN SMD 7/29/2005
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 PLATE GP - SCREED
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30' .25
.XX
.XXX =
= 0.03
0.01 FINISH = B 200-703-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 74 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG

800-889-0661
00 INITIAL RELEASE 07-30-05
1 1048-4660 STUD 1/2-13 X 6.00 34
ITEM #2 1048-2070 WAS REPLACED WITH 1048-2065, ITEM #3 1048-3150 WAS
2 1048-2065 NUT - HEX - 1/2-13 84
5994 01 REPLACED WITH 1048-3220, ITEM #4 1048-3360 WAS REPLACED WITH 1048-3370 04-06-2010 RJM
3 1048-3220 WASHER - FLAT - 1/2" SAE 50
D 4 1048-3370 WASHER - LOCK - 1/2" 52 D
5 1048-4545 STUD 1/2-13 X 3.75 16
6 1048-1220 BOLT - HEX - 1/2-13 * 1" 2

1
16X 2

SHT
01+
16X 4

REV
16X 3

16X 5

200-703-100
C

DWG
NO.
2 34X

4 34X

3 34X
B
1 34X

2X 6

NOTES:
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

SMD
DATE

7/28/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN SMD 7-29-05
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 STUD AS. - SCREED PLATE
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 SEE BOM B 200-703-100 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 75 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1006-0130 DEPTH INDICATOR 2

800-889-0661
5578 00 INITIAL RELEASE 12-17-08 RJM 2 1048-0900 BOLT - HEX - 1/4-20 * 1/2" 2
5631 01 ITEM #7, #26, AND #27 ARE ADD NEW, ITEM #22 201-144-100 WAS REPLACED WITH 02-17-09 RJM 3 4215-0002 MOUNT WD 2
201-732-100
ITEM #26 201-735-000 WAS REPLACED WITH 202-924-000, ITEM #27 201-736-000 WAS 4 200-000-061 PLATE 1
D 5779 02 06-22-09 RJM D
REPLACED WITH 202-925-000 5 200-026-000 TRACK AS. - SLIDE (LH)(EZIV)(10') 1
03 UPDATED PICTORAL VIEWS 8-16-09 6 200-025-000 TRACK AS. - SLIDE (RH)(EZIV)(10') 1
7 1012-0054 STAIR AS. - (DYNAPAC) (EZIV) 1

1
5902 04 ADDED 201-732-015, 201-732-011, 201-732-010 AND HARDWARE 10-09-2009 KAC
8 200-072-024 PLATE 2

SHT
5902 05 ADDED 300-357-000 11-16-2009 KAC
9 202-944-000 HYDRAULIC GP. - COMPLETE (DYNAPAC PROTO) 1

05
10 200-253-000 BRACKET WD - CONTROL BOX (LH) 1

REV
11 200-254-000 BRACKET WD - CONTROL BOX (RH) 1
12 1048-3150 WASHER 8
13 1048-3360 WASHER - LOCK 8
14 1048-1210 BOLT - HEX - 1/2 - 13 * 1" 8
7 15 1048-3115 WASHER - FLAT - 1/4" SAE 16

201-732-000
16 1048-3530 WASHER - EXT STAR - 1/4" 4
17 1048-0950 BOLT - HEX - 1/4-20 *1" 8
C 18 1048-2027 NUT - HEX - 1/4"-20 NYLOCK 8
19 1004-0149 BAR STOCK 2
20 1012-0130 BAR STOCK 2
5 21 201-146-200 PLATE - LH TOP COVER 1
27 22 201-732-100 PLATE - RH TOP COVER (DYNAPAC) 1
23 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 6
24 25 23

DWG
NO.
24 1048-3050 WASHER - FLAT - 1/2" USS 6
17 16 15
25 1048-3370 WASHER - LOCK - 1/2" 6
26 202-924-000 ARM AS. - SCREED (LH) (DYNAPAC) 1
27 202-925-000 ARM AS. - SCREED (RH) (DYNAPAC) 1
6 2
28 201-732-010 PLATE - SLOPE BEAM MOUNT DYNAPAC 1
29 201-732-011 PLATE - SLOPE BEAM MOUNT DYNAPAC 1
14 13 12 30 201-732-015 SLOPE BEAM WELDMENT 1
20
B 31 1048-3220 WASHER - FLAT - 1/2" SAE 4
32 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 2
19
33 1048-1205 BOLT - HEX - 1/2-13 * 1 3/4" 2
3 34 300-357-000 SONIC AUGER SENSOR MOUNT 2
1

26

22 11 17 15 18

4
8

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 12-17-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
21 ASME Y14.3M-1994
4. APPLICATION OF ENGINEERING DRAWINGS PER
CHECKED
TITLE FAB KIT - DYNAPAC (PROTO)
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING EZIV-10'
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
10 7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 3288.57
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 201-732-000 05 1 OF 3
8 7 6 5 4 3 2 1

800-889-0661 Page 76 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
PART
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION ITEM NO. DESCRIPTION QTY.
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
NUMBER
1 200-020-200 PLATE WD - SLOPE (LH)EZIV-10" 1
ECN REV. DESCRIPTION DATE DRAWN ENG 2 200-848-000 SUPPORT WD - CYLINDER (EXTENSION) 1

800-889-0661
01 REMOVED 200-321-000 & 200-322-000, REPLACED 200-322-000 w 1049-8200 02/12/03 RAJ 3 201-625-000 LEVER WD - EXTENSION 1
4 200-895-000 BLOCK AS. - SLIDE 2
02 ADDED 200-031-003 AND FASTENERS 04/06/05 RAJ
5 200-589-100 PLATE - SLOPE STOP (LH) 1
D
03 ADDED BOLT SHOULDER 1048-9209, LOCK STOVER 1048-2280 8/26/2005 PGM 6 200-077-000 COVER WD - ROD 1 D
04 REPLACED 200-020-000 WITH 200-020-200 2/2/2006 RES 7 200-520-000 RING - PISTON 2
5723 05 CHANGED SLOPE PLATE MOUNT BRACKET (ITEM#5) FROM WD. TO MACHINED PART 5/1/2009 KSB KAC 8 200-032-000 SLIDE ROD COVER PISTON 2
9 1048-3350 WASHER - LOCK - 3/8" 12

1
6055 06 UPDATED BOM 6/23/2010 RJM
10 1048-4160 BOLT - SQHSS - 5/8 - 11 * 1 1/2" 6

SHT
6070 07 ITEM #6 200-035-000 WAS REPLACED WITH 200-077-000 6/30/2010 RJM 11 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 12
6129 08 REPLACED (1) 1048-4547 WITH (1) 1048-5501 9/17/2010 KSB 12 1048-3360 WASHER - LOCK 14

09
ADDED PART #1048-0920 TO BOM, ITEM #48 QTY WAS 2 IS NOW 1, PART #1048-2200 HAS 13 1048-0515 BOLT - SHCS - 3/8 - 16 * 1" 8
6184 09 12/23/2010 RJM

REV
BEEN REMOVED FROM BOM 14 1048-3220 WASHER - FLAT - 1/2" SAE 14
15 1048-3060 WASHER - FLAT - 3/4" USS (HEAVY) 5
16 1048-1625 BOLT- HEX 2
17 1048-2565 NUT - HEX - 3/4"-10 NYLOCK 6
18 1048-3380 WASHER - LOCK 3
19 1048-1280 BOLT- HEX - 1/2 - 13 * 2 1/2" 2
20 1049-8200 BUSHING 1

200-026-000
21 4201-0106 PLATE 1
22 200-864-000 PLATE 5
C 23 1048-3180 WASHER 5
24 1048-2440 NUT - JAM - 3/4"-10 1
25 1048-9275 BOLT 1
26 1048-3240 WASHER - FLAT - 3/4" SAE 2
27 1048-9203 BOLT - SHOULDER 1
28 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
29 1048-9215 BOLT - SHOULDER SCOKET HD - 5/8 - 11 - 3/4 * 3 1/2" 1
30 1048-1328 BOLT - HEX - 5/8 - 11 * 1 1/2" 2

DWG
NO.
31 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 2
32 1048-3140 WASHER - FLAT 4
33 1048-1170 BOLT - HEX - 3/8-16 * 2 1/4" 2
34 1048-9273 BOLT - SHOULDER - 3/4-10 - 1 * 3 1/2" 1
35 1048-3250 WASHER - FLAT - 1" F436 2
36 4215-0001 CYLINDER AS. - HYDRAULIC 1
37 1048-1430 BOLT - HEX - 3/4-10 * 4" 1
38 1048-2300 NUT- LOCK - 3/4-10 1
B 39 1048-5501 STUD - 5/8-11 X 7" GRADE BD 1
40 1048-3230 WASHER - FLAT - 5/8" SAE 2
41 1048-2430 NUT - JAM - 5/8"-11 2
42 1048-2090 NUT - HEX - 5/8"-11 1
43 4215-0103 DECAL - SLOPE (LH) 1
44 200-024-000 ROD AS. - SLIDE (LH) EZIV-10 1
45 201-279-000 PLATE 1
46 1048-0930 BOLT - HEX - 1/4-20 * 3/4" 1
47 1048-3325 WASHER - LOCK - 1/4" 1
48 1048-3115 WASHER - FLAT - 1/4" SAE 1
49 200-031-005 PLATE 2
50 1048-1130 BOLT - HEX - 3/8 - 16 * 1 1/4" 4
51 1048-9209 BOLT - SHOULDER SOCKET HD - 5/8 - 11 - 3/4 * 1 1/2" 1
52 1042-0621 LOOM CLAMP-#2932; 2ID VINYL 1
53 1048-0920 BOLT - HEX - 1/4-20 * 3/4" 1

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 02-12-03
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED SCT 3-29-00
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE TRACK AS. - SLIDE (LH)(EZIV)(10')
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH =
.25
B 200-026-000 09 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 77 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING 49 2X
PRODUCTS, INC. ALL RIGHTS RESERVED.

4 2X

800-889-0661
8X 9 50

D D
35 34

2
6X 10 2X 17 15 15 16

SHT
09
REV
33 32 32 31 2X
53
52

200-026-000
13 9 8X
25 35 20 21 22 23 24
17 23 22 4X 45 6
C
46 47 48 44

43

37 38
40 40 41 41

DWG
36

NO.
39 51 28
42 18 45

1
46 47 48
28 26 15 29

B B

5
05 2X 7 8 14 12 19
2
3
26 27

2X 18 30

CARLSON
PAVING PRODUCTS, INC.

FRONT SIDE ISOMETREIC VIEW

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A NOMENCLATURE A

TRACK AS. - SLIDE (LH)(EZIV)(10')

SIZE DRAWING NUMBER REV
12X 14 12 11 B 200-026-000 09

DynapacParts.com
SHEET:
2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 78 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 4215-0151 CYLINDER - HYDRAULIC 1

800-889-0661
00 INITIAL RELEASE 10-12-04 WAD 2 1049-3220 ROD END- SPHERICAL 1
5547 01 ITEM #1 4215-0101 WAS REPLACED WITH 4215-0151 10-21-08 RJM 3 1048-2450 NUT - JAM - 3/4"-16 1

D D

1
SHT
01+
REV
4215-0001
1

DWG
NO.
3

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN WAD 10-12-04
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CYLINDER AS. - HYDRAULIC
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 12.89
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 4215-0001 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 79 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION ITEM NO. PART NUMBER DESCRIPTION QTY.
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 200-469-000 TUBE WD - SLIDE 1
ECN REV. DESCRIPTION DATE DRAWN ENG 2 200-017-000 BAR STOCK 2

800-889-0661
01 ADDED (20) LOCK WASHERS 1048-3355 & NOTE FOR LOCKTITE. 10/28/03 WAD
3 201-033-000 BAR STOCK 1
4 201-034-000 BAR STOCK 1

D 5 200-012-005 PLATE 1 D
6 1048-3350 WASHER - LOCK - 3/8" 8
7 1048-3145 WASHER - FLAT - 3/8" SAE 8

1
8 1048-1120 BOLT - HEX - 3/8-16 * 1" 8

SHT
9 1048-7210 BOLT - SHCS - 1/2 - 13 * 1 1/4" 20

01+
10 1048-0515 BOLT - SHCS - 3/8 - 16 * 1" 20

REV
11 1048-3355 WASHER - LOCK - 3/8" 20

200-024-000
10
C
11

DWG
NO.
8 5 9
6 7

2
9

11
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

ASC
DATE

03-22-01
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 3-30-00

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
10 ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
ROD AS. - SLIDE (LH) EZIV-10
NOTES: 1) ADD LOCKTITE TO EACH 1048-0515
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = B 200-024-000 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 80 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-014-200 PLATE WD- SLOPE (RH)EZIV-10" 1

800-889-0661
01 BOLT 1048-1330 WAS REPLACED BY BOLT 1048-1328 IN THE STOP BLOCK. 10/22/02 WAD 2 200-895-000 BLOCK AS. - SLIDE 2
3 200-031-000 COVER WD - ROD (RH) 1
02 REMOVED 200-321-000 & 200-322-000, REPLACED 200-322-000 w 1049-8200 05/19/04 RAJ 4 200-848-000 SUPPORT WD - CYLINDER (EXTENSION) 1
03 ADDED 200-031-003 AND FASTENERS 04/06/05 RAJ 5 200-847-000 LEVER WD - SLOPE 1
D 6 200-754-100 PLATE - SLOPE STOP (RH) 1 D
04 ADDED 1048-2280 LOCK SOVER & 1048-9209 SHOULDER BOLT 8/29/2005 PGM
7 200-032-000 SLIDE ROD COVER PISTON 2
05 REPLACED 200-014-000 WITH 200-014-200 2/1/2006 RES
8 200-520-000 RING - PISTON 2
5239 06 ITEM #20 1049-8210 WAS 1049-8200 06-07-07 MP 9 1048-3220 WASHER - FLAT - 1/2" SAE 14

1
5723 07 CHANGED SLOPE PLATE MOUNT BRACKET (ITEM #6) FROM WD. TO MACHINED PART 5/1/2009 KSB KAC 10 1048-3360 WASHER - LOCK 14

SHT
6055 08 UPDATED BOM 06-23-2010 RJM 11 1048-1280 BOLT- HEX - 1/2 - 13 * 2 1/2" 2
12 1048-0515 BOLT - SHCS - 3/8 - 16 * 1" 8

10
6129 09 REPLACED (1) 1048-4547 WITH (1) 1048-5501 9/17/2010 KSB
13 1048-3350 WASHER - LOCK - 3/8" 12

REV
6184 10 ADDED PART #1048-0920 TO BOM, ITEM #47 QTY WAS 2 IS NOW 1, PART #1048-2200 12/23/2010 RJM 14 1048-1328 BOLT - HEX - 5/8 - 11 * 1 1/2" 2
HAS BEEN REMOVED FROM BOM
15 1048-3380 WASHER - LOCK 3
16 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 12
17 1048-1625 BOLT- HEX 2
18 1048-3060 WASHER - FLAT - 3/4" USS (HEAVY) 5
19 1048-2565 NUT - HEX - 3/4"-10 NYLOCK 6

200-025-000
20 1049-8210 BUSHING 1
21 4201-0106 PLATE 5
22 1048-3180 WASHER 5
23 1048-2440 NUT - JAM - 3/4"-10 1
C
24 1048-0520 SCREW - CAP 4
25 1048-9203 BOLT - SHOULDER 1
26 1048-3240 WASHER - FLAT - 3/4" SAE 2
27 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
28 1048-9215 BOLT - SHOULDER SCOKET HD - 5/8 - 11 - 3/4 * 3 1/2" 1
29 1048-9273 BOLT - SHOULDER - 3/4-10 - 1 * 3 1/2" 1
30 1048-1170 BOLT - HEX - 3/8-16 * 2 1/4" 2

DWG
NO.
31 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 2
32 1048-3140 WASHER - FLAT 4
33 1048-3250 WASHER - FLAT - 1" F436 2
34 4215-0001 CYLINDER AS. - HYDRAULIC 1
35 1048-1430 BOLT - HEX - 3/4-10 * 4" 1
36 1048-2300 NUT- LOCK - 3/4-10 1
37 1048-5501 STUD - 5/8-11 X 7" GRADE BD 1
38 1048-3230 WASHER - FLAT - 5/8" SAE 2
39 1048-2430 NUT - JAM - 5/8"-11 2
B 40 1048-2090 NUT - HEX - 5/8"-11 1
41 4215-0102 DECAL - SLOPE (RH) 1
42 1048-4160 BOLT - SQHSS - 5/8 - 11 * 1 1/2" 6
43 200-023-000 ROD AS. - SLIDE (RH) EZIV-10 1
44 201-279-000 PLATE 1
45 1048-0930 BOLT - HEX - 1/4-20 * 3/4" 1
46 1048-3325 WASHER - LOCK - 1/4" 1
47 1048-3115 WASHER - FLAT - 1/4" SAE 1
48 200-031-005 PLATE 2
49 1048-1130 BOLT - HEX - 3/8 - 16 * 1 1/4" 4
50 1048-9209 BOLT - SHOULDER SOCKET HD - 5/8 - 11 - 3/4 * 1 1/2" 1
51 1048-9275 BOLT 1
52 1042-0621 LOOM CLAMP-#2932; 2ID VINYL 1
53 1048-0920 BOLT - HEX - 1/4-20 * 3/4" 1

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

RES
DATE

06-05-2006
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SCT 03/29/00

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 TRACK AS. - SLIDE (RH)(EZIV)(10')
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 SEE BOM B 200-025-000 10 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 81 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661 3
D

FRONT ISOMETRIC VIEW

2
12 13 8X

SHT
10
REV
11 10 9 7 8 8 2X

200-025-000
43

C
16 10 9 12X

2 2X
48 2X
53

DWG
36 35

NO.
52 49 13 4X
6X 42

27 50
41 44
45 46 47
34
15 40 37 38 38 39 39 17 18 18 19 2X
30 32 32 31 2X
B B
33 29

07 6

2X 15 14
26 25

27 26 18 28
1
51 33 20 21 22 23
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A NOMENCLATURE A

5
TRACK AS. - SLIDE (RH)(EZIV)(10')
4X 21 22 19 24 4X
SIZE DRAWING NUMBER REV

B 200-025-000 10

DynapacParts.com
SHEET:
2 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 82 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-008-000 ROD - SLIDE (RH) (10') 2

800-889-0661
01 ADDED (22) LOCK WASHERS 1048-3355 & NOTE FOR LOCKTITE. 10/29/03 WAD 2 200-470-000 TUBE WD - SLIDE 1
3 1048-1120 BOLT - HEX - 3/8-16 * 1" 8
4 1048-3145 WASHER - FLAT - 3/8" SAE 8
D D
5 1048-3350 WASHER - LOCK - 3/8" 8
6 1048-0515 BOLT - SHCS - 3/8 - 16 * 1" 22
1

1
7 1048-7210 BOLT - SHCS - 1/2 - 13 * 1 1/4" 24

SHT
8 201-037-000 BAR STOCK 1
9 201-038-000 BAR STOCK 1

01+
9 10 1048-3355 WASHER - LOCK - 3/8" 22

REV
2

200-023-000
6 10 22X

7 24X

DWG
NO.
B
8X 4 5 3

6 10

NOTES: USE LOCTITE FOR ASSEMBLY FASTENERS.

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

ASC
DATE

03-22-01
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 3-30-00

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ROD AS. - SLIDE (RH) EZIV-10
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 200-023-000 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 83 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-924-100 ARM WD - SCREED (LH)(DYNAPAC) 1

800-889-0661
5779 00 INITIAL RELEASE 06-22-09 RJM 2 1048-1500 BOLT - HEX - 1-8 * 3" 1
3 1048-2340 NUT - LOCK - 1"-8 TOPLOCK 1
4 1049-8200 BUSHING 1
D D
5 202-829-000 DECAL - DEPTH CRANK 1
6 202-819-000 EZ IV SIDEARM PIVOT PIN 1
7 1049-9340 EXTERNAL E STYLE RETAINING RING 2

1
8 1049-1030 FITTING - GREASE (STR) 1

SHT
9 1048-3237 WASHER - FLAT - 5/8" USS (HEAVY) 2

00+
10 1048-1615 BOLT- HEX - 5/8-11 * 3 1/2" 1

REV
11 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 1

202-924-000
5

C
3

DWG
NO.
2

11
9

10

6
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 7 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
A
DRAWN RJM 6/22/2009
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
8 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED KAC 6/22/2009
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ARM AS. - SCREED (LH) (DYNAPAC)
DESIGN KAC 6/22/2009
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 6/22/2009
4

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 148.72
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-924-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 84 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-925-100 ARM WD - SCREED (RH)(DYNAPAC) 1

800-889-0661
5779 00 INITIAL RELEASE 06-22-09 RJM 2 1048-1500 BOLT - HEX - 1-8 * 3" 1
3 1048-2340 NUT - LOCK - 1"-8 TOPLOCK 1
4 1049-8200 BUSHING 1
D D
5 202-829-000 DECAL - DEPTH CRANK 1
6 202-819-000 EZ IV SIDEARM PIVOT PIN 1
7 1049-9340 EXTERNAL E STYLE RETAINING RING 2

1
8 1049-1030 FITTING - GREASE (STR) 1

SHT
9 1048-3237 WASHER - FLAT - 5/8" USS (HEAVY) 2

00+
10 1048-1615 BOLT- HEX - 5/8-11 * 3 1/2" 1

REV
11 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 1

202-925-000
C

DWG
2

NO.
11 1

9
10

6
7
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 6/22/2009
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 6/22/2009
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ARM AS. - SCREED (RH) (DYNAPAC)
DESIGN KAC 6/22/2009
4 5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 6/22/2009

DynapacParts.com
8. TOLERANCES:
8 SIMILAR
TO .X = 0.10 ANGULAR = 0 30' MATERIAL: SIZE DRAWING NUMBER REV SHEET:

WT. 148.72
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-925-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 85 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 300-357-100 ROD 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 300-357-300 CLAMP, SWIVEL (1/2 x 1/2 ) 2

800-889-0661
00 INITIAL RELEASE 03-03-06 MP
3 1048-0900 BOLT - HEX 1/4-20 * 1/2" 1
4 300-357-500 TUBE - GUIDE WD. 1
D 5 1048-2400 NUT - JAM 1/2-13 1 D
6 1048-1279 BOLT- HEX - 1/2-13 * 2" 1
3

1
4

SHT
00
REV
2

300-357-000
C

DWG
NO.
B

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

MP
DATE

3/3/2006
CARLSON
PAVING PRODUCTS, INC.
A

6 2
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SONIC AUGER SENSOR MOUNT
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = B 300-357-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 86 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-119-300 ELEMENT ASSEMBLY 6

800-889-0661
5079 00 INITIAL RELEASE 10-31-06 MP 2 201-363-010 INSULATION 6

D D

1
SHT
00+
REV
202-561-100
C

DWG
NO.
B

NOTES:

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

MP
DATE

10/31/2006
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ELEMENT GP - HEAT (BLADE STYLE)
DESIGN
5. DO NOT SCALE DRAWING EZIV-10' BENT TAIL
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER EZIII-10' FLAT TAIL , EZIV-10' FLAT TAIL

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 28.35
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 202-561-100 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 87 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-119-100 ELEMENT 1

800-889-0661
5079 00 INITIAL RELEASE 10-30-06 MP 2 1042-8056 PLUG 1
5433 01 ADDED PART 1042-8041 06-20-08 RF 3 1042-8054 BACKSHELL 1
5539 02 ADDED SERVICE NOTE 10-10-08 PGM 4 1042-8055 COMPRESSION NUT 1
D D
5815 03 ADDED 5200-0198 & 1043-0138 07-29-09 RF KAC 5 1042-8041 SOCKET 16AWG, DEUTSCH 3
6 5200-0198 PVC COATED FIBERGLASS SLEEVING 11"

1
7 1043-0138 TUBE - SHRINK 1/2" 3"

SHT
CABLE WIRE LIST

03
REV
PIN TERMINAL
FUNCTION 1
OUT USED
A 1042-8041 120VAC 7
B 1042-8041 120VAC
C 1042-8041 GROUND

203-119-300
A 2

DWG
NO.
4
1

DETAIL A
SCALE 1 : 1

NOTES:
A
FOR SERVICE REPLACE ELEMENTS CRIMP PINS ON END OF WIRES.
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

MP
DATE

10/29/2006
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

SHIP PLUG & BACKSHELL LOOSE. 4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999 DESIGN
TITLE ELEMENT ASSEMBLY
5. DO NOT SCALE DRAWING 59"
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 220 V - 1 PHASE

DynapacParts.com
8. TOLERANCES:
SIMILAR 203-119-200 MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 3.14
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 203-119-300 03 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 88 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 1044-0138 THERMOSTAT, SNAP (330) 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1042-0294 DISCONNECT - MALE (16-14AWG) 2

800-889-0661
00 INITIAL RELEASE 04/21/2006 MP
3 1042-0297 CONNECTOR - SPADE 2
01 DELETED ITEMS (1043-0261 & 1043-0263) ADDED ITEM (1043-0369) 08/28/2006 MP
4 1043-0323 SHRINK TUBING (.191) 1"
5300 02 ADDED ITEM 1043-0322 09/24/2007 RF KAC
D 5 1043-0276 WIRE - HI TEMP 24" D
5388 03 REMOVED PART 1043-0322 & ADDED PART 1043-0323 04-23-08 RF KAC
6 1043-0309 TUBE - SHRINK 1/4" 1
5877 04 ADDED 1043-0276 AND DELETED 1043-0369 10-21-09 RF KAC

1
SHT
04+
REV
1044-0145
C

DWG
NO.
B

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

MP
DATE

7/31/2006
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED 7/31/2006

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE THERMOSTAT AS. 330 DEGREE
DESIGN 7/31/2006
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 7/31/2006

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 1044-0145 04+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 89 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-495-000 PLATE WD - SCREED (STR) (RH) 1

800-889-0661
00 INITIAL RELEASE 10-31-01 BKN 2 201-494-000 COVER WD - FIXED (STR) (RH) 1
5050 01 ITEM 18 201-659-000 WAS 201-471-007 10-6-06 PGM 3 201-767-000 STRIKE-OFF WD. - FIXED (18") (RH) 1
5113 02 REMOVED HARDWARE, REPLACED WITH ITEM#19 1048-0560 12/13/2006 RJM 4 202-511-000 ELEMENT AS. 1
D ITEM #2 201-470-001 WAS REPLACED WITH 201-768-000, ITEM #3 201-474-000 WAS D
5604 03 REPLACED WITH 201-767-000, PART NUMBERS 201-473-000 AND 201-494-000 HAS BEEN 12/23/2008 RJM 5 1048-3221 WASHER - FLAT - 1/2" SAE 5
REMOVED FROM BOM 6 1048-3360 WASHER - LOCK 18

1
5707 04 ITEM #2 201-768-000 WAS REPLACED WITH 201-494-000, ITEM #18 IS ADD NEW 4/13/2009 RJM 7 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 20

SHT
8 1048-3230 WASHER - FLAT - 5/8" SAE 2
9 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2

04
12 11 10 1003-0106 PLATE 5

REV
11 1048-3330 WASHER - LOCK - 5/16" 5
10 12 1048-1584 BOLT - HEX 5
13 1048-3031 WASHER - FLAT - 7/16" USS 2
14 201-535-000 PLATE 1
4 15 1046-7000 PROTECTOR - HOSE 1

201-990-000
17 16 201-659-000 BAR STOCK 2
17 1048-0560 BOLT-FHCS 1/2-13 * 2" 4
C 1 18 201-470-001 PLATE 1

14

7 13

DWG
NO.
3
18

7 6
B
8 9

16

5 6 7
NOTES:
A
1.
2.
3.
HOSE PROTECTOR NOT SHOWN.
201-659-000 WELDED IN TEST AND LEVEL.
KEEP ELEMENT WIRES OFF ELEMENTS.
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

BKN
DATE

10-31-01
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 7-5-01

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE PLATE AS. - SCREED (STR) (RH)
DESIGN
5. DO NOT SCALE DRAWING EZIV-10
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 151.6807
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-990-000 04 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 90 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-498-000 PLATE WD - SCREED (STR) (LH) EZIV-10 1

800-889-0661
00 INITIAL RELEASE 10-31-01 BKN 2 201-497-000 COVER WD - FIXED (STR) (LH) 1
01 REPLACED 201-471-007 WITH 201-783-001. 09-25-03 WAD 3 201-909-000 STRIKE-OFF WD. FIXED (18") (LH) 1
02 REPLACED (2) 1003-0106 WITH (2) 1003-0118. 07-29-04 WAD 4 202-512-000 ELEMENT AS. 1
D D
03 UPDATED TO CURRENT BUILD. 06-21-05 RAJ 5 1003-0106 PLATE 4
5050 04 201-659-000 WAS 201-471-007, ADDED NOTES. 10/10/2006 PGM 6 1048-3330 WASHER - LOCK - 5/16" 4

1
5113 05 REMOVED HARDWARE, REPLACED WITH ITEM#19 1048-0560 12/13/2006 RJM 7 1048-1584 BOLT - HEX 4

SHT
ITEM #2 201-497-000 WAS REPLACED WITH 201-914-000, ITEM #3 201-480-000 WAS 8 1048-3221 WASHER - FLAT - 1/2" SAE 4
5604 06 REPLACED WITH 201-909-000, PART NUMBERS 201-479-000, 201-476-001, AND 12/23/2008 RJM
201-575-000 HAS BEEN REMOVED FROM BOM 9 1048-3360 WASHER - LOCK 14

07
5707 07 ITEM #2 201-914-000 WAS REPLACED WITH 201-497-000, ITEM #18 IS ADD NEW 4/13/2009 RJM 10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 16

REV
11 1048-3230 WASHER - FLAT - 5/8" SAE 2
12 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
4 13 1048-3031 WASHER - FLAT - 7/16" USS 2
14 201-534-000 PLATE 1
15 201-659-000 BAR STOCK 2

201-991-000
16 1046-7000 PROTECTOR - HOSE 1
17 1048-0560 BOLT-FHCS 1/2-13 * 2" 4
C
6 7 18 201-476-001 PLATE 1

DWG
NO.
1

17 10 9 8

12 11
2
3
B

10 9

15

14

A NOTES: 18
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

BKN
DATE

10-31-01
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

1. HOSE PROTECTOR NOT SHOWN. ASME Y14.3M-1994 CHECKED SAS 7-7-01

2. 201-659-000 WELDED IN TEST AND LEVEL. 4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE PLATE AS. - SCREED (STR) (LH)
13 10 ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN
EZIV-10
3. KEEP ELEMENT WIRES OFF ELEMENTS. 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 122.6786
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-991-000 07 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 91 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-992-100 PLATE WD - SCREED (12) (RH) 1

800-889-0661
00 INITIAL RELEASE 03-22-02 WRS 2 201-459-000 COVER WD - FIXED (12) (RH) 1
01 REPLACED PARTS 201-659-000 WITH 201-783-001. 09-22-03 WAD 3 201-458-000 COVER WD - BERM (12) (RH) 1
02 REPLACED 200-955-000 WITH 1003-0106 AND 1003-0118. 07-28-04 WAD 4 201-461-000 STRIKEOFF WD - BERM (12) (RH) 1
D D
5050 03 201-659-000 WAS 201-471-007, ADDED NOTES. 10/10/2006 PGM 5 201-462-000 STRIKEOFF WD - FIXED (12) (RH) 1
5113 04 REMOVED HARDWARE, REPLACED WITH ITEM#21 1048-0560 12/13/2006 RJM 6 202-506-000 ELEMENT AS. 1

1
7 202-518-000 ELEMENT AS. 1

SHT
8 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
14 13
9 1048-3230 WASHER - FLAT - 5/8" SAE 2

04+
19 10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 20

REV
11 1048-3221 WASHER - FLAT - 1/2" SAE 5
6 12 1048-3360 WASHER - LOCK 18
13 1048-3330 WASHER - LOCK - 5/16" 6
21 14 1048-1584 BOLT - HEX 6
20 15 1046-7000 PROTECTOR - HOSE 2

201-992-000
4 16 201-535-000 PLATE 1
17 1048-3031 WASHER - FLAT - 7/16" USS 2
C 18 201-659-000 BAR STOCK 2
19 1003-0118 CLAMP WD - ELEMENT 4
1 20 1003-0106 PLATE 2
21 1048-0560 BOLT-FHCS 1/2-13 * 2" 4

DWG
10 12 11

NO.
7

3
10 12 11
5
10 12 16

B 10 17

9 8

18
2

A
NOTES:

1. HOSE PROTECTOR NOT SHOWN.

UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

03-22-02
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

CHECKED SAS
2. 201-659-000 WELDED IN TEST AND LEVEL. ASME Y14.3M-1994 7-7-01
4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE SCREED AS. - BERM (12) (RH)
3. KEEP ELEMENT WIRES OFF ELEMENTS. ASME Y14.24-1999 DESIGN WRS 04-04-02
5. DO NOT SCALE DRAWING EZIV-10
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 147.6916
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-992-000 04+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 92 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-993-100 PLATE WD - SCREED (12) (LH) 1

800-889-0661
00 INITIAL RELEASE 3-27-03 WRS 2 201-464-000 COVER WD - BERM (12) (LH) 1
01 REPLACED PARTS 201-659-000 WITH 201-783-001. 09-23-03 WAD 3 201-465-000 COVER WD - FIXED (12) (LH) 1
02 REPLACED 200-955-000 WITH 1003-0106 AND 1003-0118. 07-28-04 WAD 4 201-468-000 STRIKEOFF WD - FIXED (12) (LH) 1
D D
5050 03 201-659-000 WAS 201-471-007, ADDED NOTES. 10-10-06 PGM 5 201-467-000 STRIKEOFF WD - BERM (12) (LH) 1
5113 04 REMOVED HARDWARE, REPLACED WITH ITEM#21 1048-0560 12/13/2006 RJM 6 202-506-000 ELEMENT AS. 1

1
7 202-510-000 ELEMENT AS. 1

SHT
8 1048-3221 WASHER - FLAT - 1/2" SAE 5
20 7 9 1048-3360 WASHER - LOCK 16

04+
10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 18

REV
11 1048-3230 WASHER - FLAT - 5/8" SAE 2
12 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
13 14 13 1048-3330 WASHER - LOCK - 5/16" 5
14 1048-1584 BOLT - HEX 5
21
15 1046-7000 PROTECTOR - HOSE 2

201-993-000
19 16 201-534-000 PLATE 1
17 1048-3031 WASHER - FLAT - 7/16" USS 2
C 4 18 201-659-000 BAR STOCK 2
6 19 1003-0118 CLAMP WD - ELEMENT 4
20 1003-0106 PLATE 1
1
21 1048-0560 BOLT-FHCS 1/2-13 * 2" 4

DWG
10 9 8

NO.
12 11

10 9

18

2
10 17

CARLSON
NOTES: UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES
1. HOSE PROTECTOR NOT SHOWN. 2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN WRS 03-27-02
PAVING PRODUCTS, INC.
2. 201-659-000 WELDED IN TEST AND LEVEL. 16 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
CHECKED SAS
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 7-6-01
3. KEEP ELEMENT WIRES OFF ELEMENTS. 4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE PLATE AS. - SCREED (12) (LH)
DESIGN
5. DO NOT SCALE DRAWING EZIV-10
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 209.26740592
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-993-000 04+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 93 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-994-100 PLATE WD - SCREED (18) (RH) 1

800-889-0661
00 INITIAL RELEASE 04-02-03 WRS 2 201-471-000 COVER WD - FIXED (18) (RH) 1
01 REPLACED 201-659-000 WITH 201-783-001. 09-23-03 WAD 3 201-470-000 COVER WD - BERM (18) (RH) 1
02 REPLACED 200-955-000 WITH 1003-0106 AND 1003-0118. 07-28-04 WAD 4 201-473-000 STRIKEOFF WD - BERM (18) (RH) 1
D D
5050 03 201-659-000 WAS 201-471-007, ADDED NOTES. 10/10/2006 PGM 5 201-474-000 STRIKEOFF WD - FIXED (18) (RH) 1
5113 04 REMOVED HARDWARE, REPLACED WITH ITEM#21 1048-0560 12/13/2006 RJM 6 202-508-000 ELEMENT AS. 1

1
7 202-515-000 ELEMENT AS. 1

SHT
8 1048-3221 WASHER - FLAT - 1/2" SAE 5
9 1048-3360 WASHER - LOCK 18

04+
19
10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 20

REV
11 1048-3230 WASHER - FLAT - 5/8" SAE 2
6
12 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
13 1048-3330 WASHER - LOCK - 5/16" 6
20
14 1048-1584 BOLT - HEX 6
15 1046-7000 PROTECTOR - HOSE 2

201-994-000
10 9 8 16 201-535-000 PLATE 1
13 14
17 1048-3031 WASHER - FLAT - 7/16" USS 2
C 18 201-659-000 BAR STOCK 2
4 19 1003-0118 CLAMP WD - ELEMENT 4
20 1003-0106 PLATE 2
21 1048-0560 BOLT-FHCS 1/2-13 * 2" 4
1
7

DWG
NO.
21
3

5 12 11
B 10 9
16

10 17

A
NOTES:

1. HOSE PROTECTOR NOT SHOWN.

18
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

04-03-02
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 07-10-01

2. 201-659-000 WELDED IN TEST AND LEVEL. 4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE PLATE AS. - SCREED (18) (RH)
ASME Y14.24-1999
3. KEEP ELEMENT WIRES OFF ELEMENTS. 5. DO NOT SCALE DRAWING
DESIGN WRS 04-03-02
EZIV-10
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 145.3496
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-994-000 04+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 94 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-995-100 PLATE WD - SCREED (18) (LH) EZIV - 10' 1

800-889-0661
00 INITIAL RELEASE 02-12-02 WRS 2 201-476-000 COVER WD - BERM (18) (LH) 1
01 REPLACED 201-659-000 WITH 201-783-001 09-23-03 WAD 3 201-477-000 COVER WD - FIXED (18) (LH) 1
02 REPLACED 200-955-000 WITH 1003-0106 AND 1003-0118. 07-28-04 WAD 4 201-479-000 STRIKEOFF WD - BERM (18) (LH) 1
D 5050 03 201-659-000 WAS 201-471-007, ADDED NOTES. 10/10/2006 PGM D
5 201-480-000 STRIKEOFF WD - FIXED (18) (LH) 1
5113 04 REMOVED HARDWARE, REPLACED WITH ITEM#21 1048-0560 12/13/2006 RJM
6 202-508-000 ELEMENT AS. 1

1
15 14 7 202-505-000 ELEMENT AS. 1

SHT
8 1048-3360 WASHER - LOCK 14
20 9 1048-3221 WASHER - FLAT - 1/2" SAE 4

04+
10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 16

REV
11 1048-3230 WASHER - FLAT - 5/8" SAE 2
7
12 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
13 1046-7000 PROTECTOR - HOSE 2
14 1048-3330 WASHER - LOCK - 5/16" 5
10 8 9 15 1048-1584 BOLT - HEX 5

201-995-000
19 16 201-534-000 PLATE 1
17 1048-3031 WASHER - FLAT - 7/16" USS 2
C 5 18 201-659-000 BAR STOCK 2
6 19 1003-0118 CLAMP WD - ELEMENT 4
20 1003-0106 PLATE 1
18 21 1048-0560 BOLT-FHCS 1/2-13 * 2" 4
21

DWG
12 11

NO.
4
3

B
10 8

1
10 8

16
2
10 17

A
NOTES:

1. HOSE PROTECTOR NOT SHOWN.

UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

02-19-02
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 6-21-01

2. 201-659-000 WELDED IN TEST AND LEVEL. 4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE PLATE AS. - SCREED (18) (LH)
3. KEEP ELEMENT WIRES OFF ELEMENTS. ASME Y14.24-1999 DESIGN WRS 04-08-02
5. DO NOT SCALE DRAWING EZIV-10
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 119.9525
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-995-000 04+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 95 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-996-100 PLATE AS. - SCREED (24) (RH) 1

800-889-0661
00 INITIAL RELEASE 04-10-02 WRS 2 201-482-000 COVER WD - BERM (24) (RH) 1
01 REPLACED 201-471-007 WITH 201-783-001. 09-23-03 WAD 3 201-483-000 COVER WD - BERM (24) (RH) 1
02 REPLACED 200-955-000 WITH 1003-0106 AND 1003-0118. 07-28-04 WAD
4 201-485-000 STRIKEOFF WD - BERM (24) (RH) 1
D 03 CHG: ITEM 18 IS: 201-471-007; WAS: 201-783-001 10-23-04 WAD D
5 201-486-000 STRIKEOFF WD - BERM (24) (RH) 1
5050 04 201-659-000 WAS 201-471-007, ADDED NOTES. 10/10/2006 PGM
6 202-507-000 ELEMENT AS. 1
5113 05 REMOVED HARDWARE, REPLACED WITH ITEM#21 1048-0560 12/13/2006 RJM

1
7 202-509-000 ELEMENT AS. 1
6024 06 REPLACED 201-966-100 WITH 203-996-100 5-6-2010 BRM KAC

SHT
8 1048-3221 WASHER - FLAT - 1/2" SAE 5
9 1048-3360 WASHER - LOCK 18

06
10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 20

REV
11 1048-3330 WASHER - LOCK - 5/16" 6
6 12 1048-1584 BOLT - HEX 6
13 1048-3230 WASHER - FLAT - 5/8" SAE 2
19
14 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
21 15 1046-7000 PROTECTOR - HOSE 2

201-996-000
20 16 201-535-000 PLATE 1
11 12
17 1048-3031 WASHER - FLAT - 7/16" USS 2
C 4 18 201-659-000 BAR STOCK 2
19 1003-0118 CLAMP WD - ELEMENT 4
20 1003-0106 PLATE 2
21 1048-0560 BOLT-FHCS 1/2-13 * 2" 4
1

DWG
7

NO.
10 9 8

2
5
16

B 10 9 8 14 13

10 17

10 9

18

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

04-10-02
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 07-09-01

N O TES:
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SCREED AS. - BERM (24) (RH)
DESIGN WRS 04-10-02
5. DO NOT SCALE DRAWING EZIV-10
1. HO SE PROTECTOR NO T SHO W N. 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
2. 2 0 1 -6 5 9 - 0 0 0 W E L D E D I N T E S T A N D L E V E L .

DynapacParts.com
8. TOLERANCES:
3. K E E P E L E M E N T W IR E S O F F E L E M E N T S . SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 143.6603
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-996-000 06 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 96 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-997-100 PLATE WD - LOWER (24) (LH) 1

800-889-0661
00 INITIAL RELEASE 10-17-01 SAS 2 201-489-000 COVER WD - FIXED (24) (LH) EZIV-10 1
01 REPLACED 201-471-007 WITH 201-783-001. 07-28-04 WAD 3 201-488-000 COVER WD - BERM (24) (LH) 1
02 REPLACED 200-955-000 WITH 1003-0106 AND 1003-0118. 10-23-04 WAD 4 201-491-000 STRIKEOFF WD - BERM (24) (LH) 1
D D
5050 03 201-659-000 WAS 201-471-007. 10-11-06 PGM 5 201-492-000 STRIKEOFF WD - BERM (24) (LH) 1
5113 04 REMOVED HARDWARE, REPLACED WITH ITEM#21 1048-0560 12/13/2006 RJM 6 202-507-000 ELEMENT AS. 1

1
6024 05 REPLACED 201-997-100 WITH 203-997-100 05-06-2010 BRM KAC 7 202-514-000 ELEMENT AS. 1

SHT
8 1048-3221 WASHER - FLAT - 1/2" SAE 4
9 1048-3360 WASHER - LOCK 15

05
10 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 17

REV
11 1048-3230 WASHER - FLAT - 5/8" SAE 2
12 1048-2280 NUT - LOCK - 5/8"-11 TOPLOCK 2
13 1048-3330 WASHER - LOCK - 5/16" 5
20 14 1048-1584 BOLT - HEX 5
15 1046-7000 PROTECTOR - HOSE 2

201-997-000
13 14 7
16 201-534-000 PLATE 1
17 1048-3031 WASHER - FLAT - 7/16" USS 2
C 19 18 201-659-000 BAR STOCK 2
19 1003-0118 CLAMP WD - ELEMENT 4
5
20 1003-0106 PLATE 1
1 21 1048-0560 BOLT-FHCS 1/2-13 * 2" 4

DWG
NO.
21 6
10 9 8

12 11

B
4 10 9

18

10 17
A
16
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

BKN
DATE

10-17-01
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED SAS 7-6-01

N O TES: 4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE PLATE AS. - SCREED (24) (LH)
DESIGN
5. DO NOT SCALE DRAWING EZIV-10
1. H OS E PR OT EC TO R N OT SH OW N . 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
2. 20 1 -6 5 9- 00 0 W E L D E D IN T E S T A N D L E V E L . 8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
3. K E E P E L E M E N T W IR E S O F F E L E M E N T S . TO .X = 0.10 ANGULAR = 0 30'
WT. 117.0791
.XX
.XXX =
= 0.03
0.01 FINISH = 125 SEE BOM B 201-997-000 05 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 97 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1012-0037 STAIR WD - LOWER 1

800-889-0661
5631 00 INITIAL RELEASE 02-17-09 RJM 2 1012-0040L RAIL WD - STAIR (LH) 1
5700 01 ITEM #25 1020-0314 WAS REPLACED WITH 1020-0304 04-03-09 RJM 3 1012-0040R RAIL WD - STAIR (RH) 1
5892 02 ITEM #25 201-732-016 WAS 1020-0304 11-06-09 KAC 4 1012-0045 STAIR AS. 1
D D
5943 03 ITEM #25 201-732-016 WAS REPLACED WITH 410-100-125 1-22-2010 RJM 5 1048-3140 WASHER - FLAT 16
5962 04 ITEM#26 IS ADD NEW 02-11-2010 RJM 6 1048-3350 WASHER - LOCK - 3/8" 22
7 1048-1115 BOLT - HEX - 3/8 - 16 * 1" 8

1
8 1048-3401 BOLT - HEX - 3/8-16 * 3/4" 8

SHT
9 1020-0180 PLATE 1

04+
10 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 4

REV
11 1048-1150 BOLT - HEX - 3/8-16 * 1 3/4" 4
12 1048-3145 WASHER - FLAT - 3/8" SAE 12
13 1048-1330 BOLT - HEX - 5/8-11 * 2" 4
3 14 1048-3230 WASHER - FLAT - 5/8" SAE 4
15 1048-3380 WASHER - LOCK 6

1012-0054
16 1048-3130 WASHER - FLAT - 5/16" SAE 4
17 1048-1130 BOLT - HEX - 3/8 - 16 * 1 1/4" 2
2
C 7 18 1048-2050 NUT - HEX - 3/8"-16 2
19 1012-0181 PLATE 1
20 1048-1048 BOLT - HEX - 5/16-18 * 3/4" 4
21 1048-3340 WASHER - LOCK - 5/16" 4
5 6 8 22 1048-1620 BOLT - HEX - 5/8-11 * 4" 2
11 12 23 200-852-000 TUBE 2

DWG
9

NO.
24 1048-3175 WASHER 2
25 400-100-125 PLATE - VALVE MOUNT 1
25 26 202-862-100 STORAGE TRAY AS. 2

B
12 17 20 21 16

19
10 6 12

12 6 18

1
26

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A A
4 15 14 13
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 02-17-2009
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
23 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
24 15 22 4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE STAIR AS. - (DYNAPAC) (EZIV)
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 239.01
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 1012-0054 04+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 98 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION ITEM NO. PART NUMBER DESCRIPTION QTY.
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 1012-0043 STEP WD - REAR (LOWER) 1
ECN REV. DESCRIPTION DATE DRAWN ENG 2 1012-0044 STEP WD - LOWER 1

800-889-0661
5569 01 CHANGED LOWER STEP FROM CHANNEL TO BENT PLATE 11/18/2008 KSB
3 1048-9260 BOLT - SHOULDER SOCKET HD - 1/2 * 2 1/2" 2
4 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 2
D 5 1048-3145 WASHER - FLAT - 3/8" SAE 2 D

1
SHT
00+
REV
1012-0045
3
1
C

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 03/17/2005
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE STAIR AS.
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 1012-0045 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 99 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-862-210 STORAGE TRAY WD. 1

800-889-0661
5962 00 INITIAL RELEASE 02-11-2010 RJM 2 203-555-050 STAUFF CLAMP #5320 PP 2
6016 01 CHANGED STAUFF CLAMPS, REPLACED 202-862-110 WITH 202-862-210 4/27/2010 KSB KAC 3 203-555-048 STAUFF CLAMP #5381 PP 2
4 1048-2200 NUT - HEX - 1/4"-20 TOPLOCK 8
D D
5 203-555-049 COVER PLATE 8
6 1048-1042 BOLT - HEX - 1/4-20 * 3" 8

1
SHT
01+
REV
6
01

5
01

202-862-100
3
01
C 2
01
NOTE: ITEM #2 AND #3 COME AS A SET OF (2).
1
01 STACK ITEM #2 AND #3 (4) PLACES AS SHOWN
BELOW

DWG
NO.
5
01

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 02-11-2010
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 02-11-2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE STORAGE TRAY AS.
DESIGN KAC 02-11-2010
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 02-11-2010

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 20.92
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-862-100 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 100 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-992-000 ENDGATE AS. - LH (STANDARD) (HWE) 1

800-889-0661
6002 00 INITIAL RELEASE 04-14-2010 RJM 2 202-993-000 ENDGATE AS. - RH (STANDARD) (HWE) 1
3 200-791-000 PLATE 2
4 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 8
D D
5 1048-2065 NUT - HEX - 1/2-13 12
6 1048-3220 WASHER - FLAT - 1/2" SAE 16
7 1048-3370 WASHER - LOCK - 1/2" 8

1
SHT
00+
REV
1

202-991-000
C

DWG
NO.
2

B 5 6

4 7 6
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 04-14-2010
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ENDGATE GP. - STANDARD (HWE)
DESIGN
5. DO NOT SCALE DRAWING EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 386.52
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-991-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 101 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-621-100 ENDGATE AS. - FIXED (LH) 1

800-889-0661
6002 00 INITIAL RELEASE 04/14/2010 RJM 2 202-784-200 ENDGATE WD. - FLOATING (LH) (HEATED) 1
3 202-784-300 SHOE - LH (ENCLOSED SPRING) 1
4 201-563-000 PLATE 1
D D
5 4209-1130 SPRING - 7" 2
6 201-364-000 PLATE 2
7 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 9

1
11 14 7 8 1048-1121 BOLT - HEX - 3/8 - 16 * 3" 2

SHT
9 1048-1155 BOLT - HEX - 3/8-16 * 1 3/4" 2

00+
10 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 4

REV
11 1048-3221 WASHER - FLAT - 1/2" SAE 9
5
12 1048-3145 WASHER - FLAT - 3/8" SAE 4
13 1048-3032 WASHER - FLAT - 3/8" USS 2
14 1048-3370 WASHER - LOCK - 1/2" 9
13 9

202-992-000
C

11 14 7

DWG
NO.
2

10 12 12 8

10

3 11 14 7

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A
4 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN
A
RJM 04-14-2010
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ENDGATE AS. - LH (STANDARD) (HWE)
DESIGN
5. DO NOT SCALE DRAWING EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 188.26
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-992-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 102 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-622-100 ENDGATE AS.- FIXED (RH) 1

800-889-0661
6002 00 INITIAL RELEASE 04-14-2010 RJM 2 202-785-200 ENDGATE WD. - FLOATING (RH) (HEATED) 1
3 202-785-300 SHOE - RH (ENCLOSED SPRING) 1
4 201-563-000 PLATE 1
D D
5 4209-1130 SPRING - 7" 2
6 201-364-000 PLATE 2
7 1048-1231 BOLT - HEX - 1/2-13 * 1 1/4" 9

1
11 14 7 8 1048-1121 BOLT - HEX - 3/8 - 16 * 3" 2

SHT
9 1048-1155 BOLT - HEX - 3/8-16 * 1 3/4" 2

00+
10 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 4

REV
11 1048-3221 WASHER - FLAT - 1/2" SAE 9
12 1048-3145 WASHER - FLAT - 3/8" SAE 4
13 1048-3032 WASHER - FLAT - 3/8" USS 2
5
14 1048-3370 WASHER - LOCK - 1/2" 9
2

202-993-000
13 9
C 8 12 12 10

1 7 14 11
4

DWG
NO.
11 14 7

10
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 04-14-2010
PAVING PRODUCTS, INC.
3
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ENDGATE AS. - RH (STANDARD) (HWE)
DESIGN
5. DO NOT SCALE DRAWING EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 192.18
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-993-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 103 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 1042-8028 MOUNTING CLIP 2
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1042-8023 DEUTSCH 4 PIN PLUG 2

800-889-0661
6118 00 INITIAL RELEASE 09-08-2010 RJM
3 1048-3145 WASHER - FLAT - 3/8" SAE 4
6387 01 PART NUMBERS #202-785-600 AND #202-784-600 HAS BEEN REMOVED FROM BOM 10-12-2011 RJM KAC
4 1048-3401 BOLT - HEX - 3/8-16 * 3/4" 2
D 5 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 2 D
6 202-784-500 HEATED ENDGATE HARNESS SUPPORT WD. 2
7 1048-3221 WASHER - FLAT - 1/2" SAE 10

1
8 1048-1205 BOLT - HEX - 1/2-13 * 1 3/4" 4

SHT
9 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4
14 15 7
10 202-784-400 ELEMENT AS. 2

01
REV
11 202-783-100 INSULATION - ELEMENT 2
12 203-336-000 PLATE - HEATED ENDGATE ELEMENT COVER (LH) 1
16 12 13 203-337-000 PLATE - HEATED ENDGATE ELEMENT COVER (RH) 1
14 1048-1245 BOLT - HEX - 1/2-13 * 1 1/2" 2
15 1048-3370 WASHER - LOCK - 1/2" 2

203-340-000
16 300-356-200 ELECTRICAL HARNESS AS. - RH 1
17 300-356-250 ELECTRICAL HARNESS AS. - LH 1
C

6 7 8

DWG
NO.
13 4 3
B

9 7

10
5 3 1 2

11

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

RJM
DATE

09/08/2010
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE STANDARD HEATED ELEMENT KIT
5. DO NOT SCALE DRAWING
DESIGN
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 414.80
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 203-340-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 201-980-000 ELEMENT 1

800-889-0661
5504 00 INITIAL RELEASE 9/22/2008 THH THH 2 1042-8021 CONNECTOR, 4 SOCKET 1
6118 01 ADDED WIRING CHART 9/08/2010 RJM 3 1042-8041 SOCKET 16AWG, DEUTSCH 3
4 1042-8031 WEDGELOCK W4S 1
D D
5 202-540-000 SEAL- ELECTRICAL 1

1
SHT
01+
REV
202-784-400
NOTE: USE THE FULL LENGTH OF THE ARMORED SLEEVE WHEN
C ATTACHING THE CONNECTOR.

DWG
NO.
B

PLUG TERMINAL USED AWG LENGTH WIRE# FUNCTION

1 1042-8040 16 2.4' L1 120VAC
2 1042-8040 16 2.4' L2 120VAC
3 202-540-000
4 1042-8040 16 2.4' GRD GROUND

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN THH 9/22/2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ELEMENT AS.
DESIGN THH 9/19/2008
5. DO NOT SCALE DRAWING HEATED ENDGATE (34.5")
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER THH 9/19/2008 EZIV

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 4.21
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-784-400 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 105 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8102 PLUG MS3108B20-19P 1

800-889-0661
5504 00 INITIAL RELEASE 9/22/2008 THH THH 2 1042-8110 STRAIN RELIEF - AMPHENOL 1
3 1043-0490 CORD - SOOW (16AWG)(3CONDUCTOR) 2.4'
4 1045-0003 ARMOUR SLEEVE 2.4'
D D
5 1042-8023 DT04-4P DEUTSCH 4 PIN PLUG 1
6 1042-8033 W4P WEDGELOCK 1
7 1042-8040 CONTACT PIN SIZE 16 3

1
8 202-540-000 SEAL- ELECTRICAL 1

SHT
NOTE: CLOCKING DIRECTION

00+
REV
LH IS AS SHOWN. RH IS AS SHOWN.
"3:00 O'CLOCK" "9:00 O'CLOCK"

C D B
A

A D C
B

300-356-200
C 1

3 4

DWG
NO.
2

WIRE LIST
PLUG PLUG TERMINAL WIRE
WIRE AWG WIRE # FUNCTION
1 2 USED LENGTH
A 1 1042-8040 16 2.4' LI 110VAC
B 2 1042-8040 16 2.4' L2 110VAC
3 202-540-000
C 4 1042-8040 16 2.4' GRD GROUND

5 6 7 8

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN THH 9/22/2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE ELECTRICAL HARNESS AS. - RH
DESIGN THH 9/19/2008
5. DO NOT SCALE DRAWING HEATED ENDGATE
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER THH 9/19/2008

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 300-356-200 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 106 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-875-640 TAPER ENDGATE SHOE WD. 1

800-889-0661
6151 00 INITIAL RELEASE 10/14/2010 KSB KAC 2 601-750-200 WELD - LH CONV. DOOR HINGE 1
3 601-750-300 WELD - RH CONV. DOOR HINGE 1
4 1048-0509 BOLT - 3/8-16 X 1 1/4 FHCS 4
D D
5 1048-3145 WASHER - FLAT - 3/8" SAE 4
6 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 4
7 1048-3220 WASHER - FLAT - 1/2" SAE 3

1
8 1048-3370 WASHER - LOCK - 1/2" 2

SHT
14 9 1048-1205 BOLT - HEX - 1/2-13 * 1 3/4" 2

00+
10 1048-2431 NUT - JAM - 5/8"-18 1

REV
11 202-984-032 RIGHT - HAND THREAD BALL JOINT ROD END 1
12 1048-9263 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/4" 1
13 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 1
14 202-984-301 JACK - SIDE HANDLE WD. 1
15 202-875-605 ENDGATE WD. - FLOATING (RH) 1

202-875-600
15

4
2

6 5

DWG
NO.
12

9 8 7
10

B
7 13

11

3
1

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

KSB
DATE

9/22/2010
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 9/22/2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE TAPERED ENDGATE ASSEMBLY - RH
DESIGN KAC 9/22/2010
5. DO NOT SCALE DRAWING NON-HEATED
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 9/22/2010
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 129.20
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-875-600 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 107 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-875-705 ENDGATE WD. - FLOATING (LH) 1

800-889-0661
6169 00 INITIAL RELEASE 11/22/2010 KSB KAC 2 202-875-740 TAPER ENDGATE SHOE WD. - LH 1
3 601-750-200 WELD - LH CONV. DOOR HINGE 1
4 601-750-300 WELD - RH CONV. DOOR HINGE 1
D D
5 1048-0509 BOLT - 3/8-16 X 1 1/4 FHCS 4
6 1048-3145 WASHER - FLAT - 3/8" SAE 4
7 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 4

1
8 1048-3220 WASHER - FLAT - 1/2" SAE 3

SHT
15 9 1048-3370 WASHER - LOCK - 1/2" 2

00+
10 1048-1205 BOLT - HEX - 1/2-13 * 1 3/4" 2

REV
11 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 1
12 1048-9263 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/4" 1
13 202-984-032 RIGHT - HAND THREAD BALL JOINT ROD END 1
14 1048-2431 NUT - JAM - 5/8"-18 1
15 202-984-301 JACK - SIDE HANDLE WD. 1

202-875-700
1

5
4

DWG
NO.
12
6 7

10
B
9 11 8

8 14

13

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

KSB
DATE

11/22/2010
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 11/22/2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE TAPERED ENDGATE ASSEMBLY - LH
DESIGN KAC 11/22/2010
5. DO NOT SCALE DRAWING NON-HEATED
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 11/22/2010
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 127.36
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-875-700 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 108 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-784-400 ELEMENT AS. 1

800-889-0661
6151 00 INITIAL RELEASE 10/14/2010 KSB KAC 2 202-875-626 PLATE - ELEMENT HOLD DOWN STRIP 1
3 202-783-100 INSULATION - ELEMENT 1
4 1048-2050 NUT - HEX - 3/8"-16 3
D D
6 5 1048-1134 BOLT - HEX 3
6 300-356-200 ELECTRICAL HARNESS AS. - RH 1

1
SHT
00+
REV
202-875-620
C

DWG
NO.
5

4 1

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

KSB
DATE

10/15/2010
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 10/15/2010
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE HEAT KIT - RH
DESIGN KSB 10/15/2010
5. DO NOT SCALE DRAWING TAPERED ENDGATE ASSEMBLY
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 10/15/2010
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 10.47
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-875-620 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 109 of 251

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 110 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 111 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 112 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 113 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 114 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 115 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 116 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1047-0119 SEAL KIT - COUNTERBALANCE VALVE REF

800-889-0661
01 4/20/2007
ITEM #1)1047-0119 IS SUN #99-011-007
02 VENDOR# NOW CBCA-LHN-Z6Q 10/16/2007 MSOU

D D

1
1.70

SHT
01+
REV
1047-0116
0

DWG
NO.
B
7.81

6.31

4.99

2.74

1.43

VENDOR: SUN HYDRUALICS

3:1 PILOT RATIO
RATED TO 3000 PSI UNLESS OTHERWISE SPECIFIED

CARLSON
APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
REVERSE FLOW CHECK OF 25 PSI INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN RES 06-28-06
PAVING PRODUCTS, INC.
INCLUDES O-RINGS 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED PLM 06-29-07
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE VALVE - COUNTERBALANCE
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = #CBCA-LHN-Z6Q B 1047-0116 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 117 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-952-300 CYLINDER - HYDRAULIC 2

800-889-0661
00 INITIAL RELEASE 02/17/2003 RAJ 2 200-684-000 CLEVIS - CYLINDER (BERM) 2
5547 01 ITEM #1 200-362-000 WAS REPLACED WITH 202-952-000 10/21/2008 RJM 3 1048-9255 BOLT - SHOULDER SOCKET HD - 1/2 * 1 3/4" 4
02 ITEM#1 202-952-300 WAS 202-952-000, ALSO REMOVED CYLINDER SPACER 4-15-2010 KAC 4 1048-2053 NUT - HEX - 3/8"-16 NYLOCK 4
D D
5 1048-2395 NUT - JAM - 1/2"-20 2

1
2

SHT
02
REV
200-689-000
2
C

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 02/17/03
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BERM GP - 12"
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 13.97
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 200-689-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 118 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-952-200 SEAL KIT - HIGH TEMP 1

800-889-0661
- 00 INITIAL RELEASE 04-16-2010 KAC

D D

1
SHT
00+
REV
202-952-300
C

DWG
NO.
B

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

KAC
DATE

10/7/2008
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED 10/7/2008

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN 10/7/2008
CYLINDER - HYDRAULIC
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 10/7/2008 12" EZ IV BERM

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
125 SEE NOTE B 202-952-300 00+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 119 of 251

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 120 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 121 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 122 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2006 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1047-0081 COIL - DIN CONNECTOR - 24V 2

800-889-0661
01 4/23/2007 2 1047-0061 VALVE AS. - SOLENOID 1
3 1047-0087 COIL NUT - INCLUDES MANUAL OVERRIDE 2

D D

1
SHT
01
REV
1

1047-0080
C

DWG
NO.
1

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN KAC 12/27/2006
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 12/27/2006
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SOLENOID VALVE WITH COIL - 24 V
DESIGN KAC 12/27/2006
5. DO NOT SCALE DRAWING DIN CONNECTOR
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 12/27/2006

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 6.639
.XX
.XXX =
= 0.03
0.01 FINISH = 125
DG4V-3S--6C-H-M-U-D2-H7-60-EN490 B 1047-0080 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 123 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-952-400 CYLINDER - HYDRAULIC 2

800-889-0661
XXXX 00 INITIAL RELEASE 02/17/03 RAJ 2 200-684-000 CLEVIS - CYLINDER (BERM) 2
5547 01 ITEM #1 200-362-000 WAS REPLACED WITH 202-952-000 10/21/08 RJM 3 1048-9255 BOLT - SHOULDER SOCKET HD - 1/2 * 1 3/4" 4
02 ITEM #1 202-952-400 WAS 252-952-000, ALSO REMOVED SPACER 04-16-2010 KAC 4 1048-2053 NUT - HEX - 3/8"-16 NYLOCK 4
D D
5 1048-2395 NUT - JAM - 1/2"-20 2

1
SHT
4

02
REV
2

200-748-000
C

1 3

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 02/17/03
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BERM GP - 18"
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 14.22
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 200-748-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 124 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-952-200 SEAL KIT - HIGH TEMP 1

800-889-0661
- 00 INITIAL RELEASE 04-16-2010 KAC

D D

1
SHT
00+
REV
202-952-400
C

DWG
NO.
B

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

KAC
DATE

10/7/2008
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED 10/7/2008

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN 10/7/2008
CYLINDER - HYDRAULIC
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 10/7/2008 18" EZ IV BERM

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
125 SEE NOTE B 202-952-400 00+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 125 of 251

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 126 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-952-500 CYLINDER - HYDRAULIC 2

800-889-0661
XXXX 00 INITIAL RELEASE XX/XX/XX RAJ 2 200-684-000 CLEVIS - CYLINDER (BERM) 2
5547 01 ITEM #1 200-362-000 WAS REPLACED WITH 202-952-000 10/21/08 RJM 3 1048-9255 BOLT - SHOULDER SOCKET HD - 1/2 * 1 3/4" 4
02 ITEM#1 202-362-500 WAS 202-362-000, ALSO REMOVED SPACERS 4-16-10 KAC 4 1048-2053 NUT - HEX - 3/8"-16 NYLOCK 4
D D
5 1048-2395 NUT - JAM - 1/2"-20 2

1
SHT
02
REV
200-751-000
C 4 2
1
3

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 02/17/03
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BERM GP - 24"
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 14.31
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 200-751-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 127 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-952-200 SEAL KIT - HIGH TEMP 1

800-889-0661
- 00 INITIAL RELEASE 04-16-2010 KAC

D D

1
SHT
00+
REV
202-952-500
C

DWG
NO.
B

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

KAC
DATE

10/7/2008
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED 10/7/2008

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN 10/7/2008
CYLINDER - HYDRAULIC
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER 10/7/2008 24" EZ IV BERM

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
125 SEE NOTE B 202-952-500 00+ 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 128 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1030-0028 SOLENIOD VALVE 7

800-889-0661
00 INITIAL RELEASE 01-01-2010 2 1030-0029 OVERCENTER VALVE 14
01 REDESIGNED BLOCK TO REMOVE SEQUENCE VAVLE 01-24-2010 3 1030-0031 CHECK VAVLE 18
4 1030-0032 CAVITY PLUG 4
D D
5 1030-0033 COIL 24V 14
6 1030-0034 COIL SPACER 7
7 1030-0038 SOLENIOD VAVLE 4

1
8 1030-0039 COIL 24V 4

SHT
00+
REV
1030-0025
C
2
4

1 5 6

DWG
8 7

NO.
A1 B1 A2 B2 A3 B3 A4 B4 A5 B5 A6 B6 A7 B7 A8 B8 A9 B9

5A 5M 5C 5B 5E 5D 5G 5F 5I 5H 5K 5J 5L 5N
8B 8A 8C 8D

7B 7A 7F 7E 7H 7G 7J 7I 7L 7K 7N 7M 7P 7O 7R 7Q 7C 7D
B LS1
6A 6B
LS2

2B 2A 4B 4C 4D 4E 4F 4G 4A 2D 2C
P1 P2

T1 T2

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN KAC 11-06-2009
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SOLENIOD VALVE
DESIGN
5. DO NOT SCALE DRAWING 24V
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER EATON PART NUMBER :X630AA00655A

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 182.46
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 1030-0025 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 129 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 2 201-672-000 00 SCREW AS. - DEPTH 16" (RH)

D
D

800-889-0661

C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE DEPTH SCREW GP. - STANDARD

DynapacParts.com
APPROVALS DATE
DESIGN
WAD 5-21-03
MODEL
WAD 5-21-03 SIZE DWG. NO. REV.
A 202-559-000

800-889-0661
DRAFT
WAD 5-21-03 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 130 of 251 1-1
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-671-100 00 HOUSING AS. - SCREW (16")
2 1 201-674-000 02 BAR - DEPTH CRANK (RH) THREADED NUT
D 3 1 1049-3050 00 BEARING
D

800-889-0661
4 2 1049-1040 FITTING - GREASE
5 4 1048-7065 BOLT - CAP
6 1 1010-7210 00 BAR STOCK
7 1 1006-0128 DECAL - RH
8 2 1048-1900 SCREW - DRIVE

C C

1 B
B

2
5
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A 6 SCREW AS. - DEPTH 16" (RH)
A

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE

7 APPROVALS DATE
DESIGN
SAS 10-30-01 SIZE DWG. NO. REV.

8
A 201-672-000SHEET 00

800-889-0661
DRAFT
SAS 10-30-01 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 131 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 132 of 251
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
Page 133 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
PARTS LIST
ITEM NO. PART NUMBER DESCRIPTION QTY
1 4209-0021 JACK AS. - (SIDE HANDLE) 4

D 800-889-0661 D

1
SHT
00+
REV
4200-0011
C

DWG
NO.
B

NOTES:

UNLESS OTHERWISE SPECIFIED

CARLSON
APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN WAD 3/10/2004
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED WAD 3/10/2004
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE KIT- JACK (SIDE HANDLE) ENCLOSED SPRING
DESIGN WAD 3/10/2004
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 4200-0011 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
Page 134 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 4209-0003A JACK, SIDE HANDLE, END GATE AS.
2 1 4209-0156 00 BAR STOCK
D
D

800-889-0661

C C

B B

2
CARL SON PAVI NG PRODUCTS I NC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE JACK AS. - (SIDE HANDLE)

DynapacParts.com
APPROVALS DATE
ENCLOSED SPRING
DESIGN
WAD 03-10-04
MODEL
WAD 03-10-04 SIZE DWG. NO. REV.
A 4209-0021 00

800-889-0661
DRAFT
WAD 03-10-04 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 135 of 251
 DynapacParts.com
EZIV BOLT-ON WITH ENDGATES INSTALLATION
800-889-0661
INSTRUCTIONS

STEP 1 STEP 2

DynapacParts.com
800-889-0661
Page 136 of 251
 DynapacParts.com
STEP 3
800-889-0661 STEP 4

DynapacParts.com
800-889-0661
Page 137 of 251
 DynapacParts.com
STEP 5
800-889-0661 STEP 6

DynapacParts.com
800-889-0661
Page 138 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-233-500 SUPPORT BRACKET (WIDEPAVE) (LH) 1

800-889-0661
00 INITIAL RELEASE 12-08-08 RJM 2 1004-0243 BRACKET GP - WIDEPAVE 1
3 200-234-500 SUPPORT BRACKET (WIDEPAVE) (RH) 1

D D

1
SHT
00+
REV
1

200-233-600
C

DWG
NO.
3
1004-0017L

NOTE: SEE 1004-0017L AND 1004-0017R FOR

INSTALLATION INSTRUCTIONS.
2

1004-0017R
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 11-18-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SUPPORT BRACKET GP.
DESIGN
5. DO NOT SCALE DRAWING EZIV (WIDEPAVE)
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 82.53
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-233-600 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 139 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-233-300 SUPPORT BRACKET WD. (LH) 1

800-889-0661
5570 00 INITIAL RELEASE 11-18-08 RJM 2 1048-2430 NUT - JAM - 5/8"-11 1
3 1048-4612 BOLT - SQHSS - 5/8 - 11 * 2" 1

D D

1
SHT
00+
REV
200-233-500
C

DWG
NO.
1

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 11-18-08
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SUPPORT BRACKET (WIDEPAVE) (LH)
DESIGN
5. DO NOT SCALE DRAWING EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 6.95
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-233-500 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 140 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-234-400 SUPPORT BRACKET WD. (RH) 1

800-889-0661
5570 00 INITIAL RELEASE 12-02-08 RJM 2 1048-2430 NUT - JAM - 5/8"-11 1
3 1048-4612 BOLT - SQHSS - 5/8 - 11 * 2" 1

D D

1
SHT
00+
REV
1

200-234-500
C

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 12-02-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SUPPORT BRACKET (WIDEPAVE) (RH)
DESIGN
5. DO NOT SCALE DRAWING EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 6.91
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-234-500 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 141 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-970-000 00 BOLT ON AS. - UPPER (12) (LH)
2 1 200-913-000 01 BOLT ON AS. - LOWER (12) (LH)
D
D

800-889-0661

C 1 C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON GP - (12) (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
ELECTRIC HEAT
APPROVALS DATE
DESIGN DWG. NO. REV.
SIZE
A 200-428-000 00

800-889-0661
DRAFT
RAJ 11-13-00 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 142 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-161-000 03 BOLT ON WD - UPPER (12) (LH)
2 4 1048-3221 WASHER
D 3 4 1048-3370 WASHER - LOCK
D

800-889-0661
4 4 1048-2070 NUT - HEX
2
3
4

C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - UPPER (12) (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
RAJ 09-15-03 SIZE DWG. NO. REV.
A 200-970-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 143 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-866-000 BOLT ON WD - LOWER (12) (LH) 1

800-889-0661
00 INITIAL RELEASE 07-05-00 SVL 2 1003-0106 PLATE 1
6035 01 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 3 1048-3330 WASHER - LOCK - 5/16" 1
4 1048-1584 BOLT - HEX 1
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4
7 1048-3360 WASHER - LOCK 2

1
8 1048-1260 BOLT - HEX - 1/2-13 * 2" 2

SHT
9 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2

01
10 202-734-000 ELEMENT AS. - BOLT-ON 12" (EZIII & EZIV) 1

REV
4 3 2

200-913-000
C

10

DWG
NO.
6 9

8
B
7

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SVL 07-05-00
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE BOLT ON AS. - LOWER (12) (LH)
1 ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 35.70
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-913-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 144 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM
PART NUMBER DESCRIPTION QTY
NO.
ECN REV. DESCRIPTION DATE DRAWN ENG

800-889-0661
1 201-982-000 ELEMENT 1
00 INITIAL RELEASE 06-01-05 WRS WRS 2 1042-8101 PLUG 1
3 1042-8110 STRAIN RELIEF - AMPHENOL 1
5815 01 ADDED 5200-0198, 1043-0217 & 1043-0310 07-29-09 RF KAC
D 4 1043-0217 SO CORD 14-3 26" D
5 5200-0198 PVC COATED FIBERGLASS SLEEVING 11"
6 1043-0310 HEAT SHRINK 2"

1
SHT
WIRE LIST
PINOUT WIRE NOTE: ITEM 6 IS NOT SHOWN
COLOR AWG LENGTH FUNCTION

01
PLUG 1 #

REV
A BLU/WHT L1 14 38" 120VAC 2
B BLU/WHT L2 14 38" 120VAC
C GRN/WHT PE 14 38" GROUND
3

202-734-000
C

DWG
NO.
4

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

6/1/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED WRS 6/1/2005

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN WRS 6/1/2005
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 ELEMENT AS. - BOLT-ON 12" (EZIII & EZIV)
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER WRS 6/1/2005

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-734-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 145 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-971-000 02 BOLT ON AS. - UPPER (12) (RH)
2 1 200-912-000 01 BOLT ON AS. - LOWER (12) (RH)
D
D

800-889-0661

BOLT TO
C EXTENSION 1 C
THIS SIDE

B B

BOLT TO
EXTENSION
SCREED
THIS SIDE 2

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON GP - (12) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN DWG. NO. REV.
SIZE
A 200-429-000 00

800-889-0661
DRAFT
RAJ 11-10-00 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2 1
Page 146 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-162-000 03 BOLT ON WD - UPPER (12) (RH)
2 4 1048-3221 WASHER
D 2 3 4 1048-3370 WASHER - LOCK
3 D

800-889-0661
4 4 1048-2070 NUT - HEX
4

C 1 C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - UPPER (12) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
RAJ 09-15-00 SIZE DWG. NO. REV.
A 200-971-000SHEET 02

800-889-0661
DRAFT
RM 05-13-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 147 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-865-000 BOLT ON WD - LOWER (RH) 1

800-889-0661
00 INITIAL RELEASE 06-03-05 WRS 2 1003-0106 PLATE 1
6035 01 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 3 1048-3330 WASHER - LOCK - 5/16" 1
4 1048-1584 BOLT - HEX 1
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-3360 WASHER - LOCK 2
7 1048-1260 BOLT - HEX - 1/2-13 * 2" 2

1
8 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2

SHT
9 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4

01
10 202-734-000 ELEMENT AS. - BOLT-ON 12" (EZIII & EZIV) 1

REV
4 3 2

200-912-000
C

10

8 9

DWG
NO.
5

B 6
1

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN WRS 06-03-05
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOLT ON AS. - LOWER (12) (RH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 35.70
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-912-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 148 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-600-550 12" BOLT - ON WD. - (BERM) 1

800-889-0661
6229 00 INITIAL RELEASE 02-28-2011 RJM 2 202-600-540 12" BOLT - ON AS. - LOWER (BERM) 1
3 1048-3240 WASHER - FLAT - 3/4" SAE 2
4 202-600-570 SCREW AS. - ATTACK - 12" (BERM) 1
D D
5 1048-2450 NUT - JAM - 3/4"-16 2
24 23 22 6 4204-0113 JACK AS. - ATTACK (SHORT) 1
7 1048-9020 PIN - CLEVIS 2

1
8 1048-9040 KEY - COTTER 2

SHT
9 4207-0002 BODY WD. - JACK (BERM) 1

00+
10 4207-0001 SCREW AS. - JACK (BERM) 1

REV
13 14 15 17 16 14 11 300-700-100 JUNCTION BOX AS. 1
12 1049-1030 FITTING - GREASE (STR) 1
13 1048-3230 WASHER - FLAT - 5/8" SAE 2
14 1048-3382 WASHER - LOCK - 5/8" 4
15 1048-2090 NUT - HEX - 5/8"-11 2

202-600-500
16 1048-2430 NUT - JAM - 5/8"-11 2
17 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 2
C 18 1048-1140 BOLT - HEX - 3/8-16 * 1 1/2" 1
19 1048-3090 WASHER - FLAT - #10 SAE 4
4 1
20 1048-3310 WASHER - LOCK 4
21 1048-6995 BOLT - BUTTON HEAD - 10-32 X .5" 4
22 1048-3220 WASHER - FLAT - 1/2" SAE 4
3 5 23 1048-3370 WASHER - LOCK - 1/2" 4

DWG
NO.
24 1048-2065 NUT - HEX - 1/2-13 4
18

12
10

11
B 6
7

19 20 21 9

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

RJM
DATE

02-28-2011
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 02-28-2011
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOLT - ON GP. - 12" (BERM)
5. DO NOT SCALE DRAWING
DESIGN KAC 02-28-2011
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 02-28-2011
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 180.94
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 202-600-500 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 149 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED Default/
ITEM NO. PART NUMBER DESCRIPTION
QTY
ECN REV. DESCRIPTION DATE DRAWN ENG
1 202-600-560 12" BOLT ON LOWER WELDMENT - (BERM) 1

800-889-0661
6229 00 INITIAL RELEASE 02-28-2011 RJM
2 202-600-541 PLATE- 12" LOWER BOLT -ON COVER - RH 1
3 202-600-542 PLATE - 12" LOWER BOLT - ON COVER - LH 1
D 4 202-506-000 ELEMENT AS. 2 D
5 1003-0106 PLATE 4
6 1048-3330 WASHER - LOCK - 5/16" 4

1
7 1048-1584 BOLT - HEX 4

SHT
8 1048-3411 BOLT - FHCS - 5/16 - 18 * 1" 4

00+
REV
7

202-600-540
4
6
C

DWG
NO.
5

8
A
3
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

RJM
DATE

02-28-2011
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 02-28-2011
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE 12" BOLT - ON AS. - LOWER (BERM)
5. DO NOT SCALE DRAWING
DESIGN KAC 02-28-2011
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 02-28-2011
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 48.7360
.XX
.XXX =
= 0.03
0.01 FINISH = 25 B 202-600-540 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 150 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-600-571 SCREW - ATTACK - 12" (BERM) 1

800-889-0661
6229 00 INITIAL RELEASE 01-01-01 2 1048-2120 NUT - HEX - 3/4"-16 1

D D

1
SHT
00+
REV
202-600-570
C

DWG
NO.
1

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

RJM
DATE

02-28-2011
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 02-28-2011
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SCREW AS. - ATTACK - 12" (BERM)
5. DO NOT SCALE DRAWING
DESIGN KAC 02-28-2011
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 02-28-2011
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.2969
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 202-600-570 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 151 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-972-000 03 BOLT ON AS. - UPPER (18) (LH)
2 1 200-915-000 02 BOLT ON AS. - LOWER (18) (LH)
D
D

800-889-0661

1
C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON GP - (18) (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN DWG. NO. REV.
SIZE
A 200-430-000 00

800-889-0661
DRAFT
RAJ 11-13-00 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2 1
Page 152 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-163-000 03 BOLT ON WD - UPPER (18) (LH)
2 4 1048-3221 WASHER
D 3 4 1048-3370 WASHER - LOCK
D

800-889-0661
4 4 1048-2070 NUT - HEX
4 3 2

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - UPPER (18) (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
RAJ 09-15-00 SIZE DWG. NO. REV.
A 200-972-000SHEET 03

800-889-0661
DRAFT
RAJ 09-15-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 153 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-868-000 BOLT ON WD - LOWER (18) (LH) 1

800-889-0661
00 INITIAL RELEASE 07-05-03 WRS 2 202-733-000 ELEMENT AS. - BOLT-ON 18" (EZIV) 1
6035 01 ITEM #8 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 3 1048-1584 BOLT - HEX 2
4 1048-3330 WASHER - LOCK - 5/16" 2
D D
5 1048-3360 WASHER - LOCK 2
6 1048-1260 BOLT - HEX - 1/2-13 * 2" 2
7 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4

1
8 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4

SHT
9 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2

01
10 1003-0106 PLATE 2

REV
3 4 10

200-915-000
C

2
7

DWG
NO.
8

6 9
5
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN WRS 07-05-03
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOLT ON AS. - LOWER (18) (LH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 48.35
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-915-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 154 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-973-000 00 BOLT ON AS. - UPPER (18) (RH)
2 1 200-914-000 01 BOLT ON AS. - LOWER (18) (RH)
D
D

800-889-0661
1

C C

B B

2
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON GP - (18) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN DWG. NO. REV.
SIZE
A 200-431-000 00

800-889-0661
DRAFT
RAJ 07-05-00 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 155 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-164-000 03 BOLT ON WD - UPPER (18) (RH)
2 4 1048-3221 WASHER
D
2 3 4
3 4 1048-3370 WASHER - LOCK
D

800-889-0661
4 4 1048-2070 NUT - HEX

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - UPPER (18) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
RAJ 09-15-00 SIZE DWG. NO. REV.
A 200-973-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 156 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-867-000 00 BOLT ON WD - LOWER (18) (RH)
2 2 1048-1584 BOLT - HEX
D 3 2 1048-3330 WASHER - LOCK
D

800-889-0661
4 2 1048-3360 WASHER - LOCK
5 2 1048-1260 BOLT - HEX
6 4 1048-2260 NUT - LOCK
2 7 4 1048-1250 BOLT- HEX
8 2 1048-3055 WASHER
3
9 2 1003-0106 00 PLATE
9 10 1 202-733-000 ELEMENT AS. - BOLT-ON 18" (EZIV)

C C

4
10
5
6
7

B B

CARLSON PAVING PRODUCTS INC.

1 18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - LOWER (18) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
SVL 07-05-00 SIZE DWG. NO. REV.
A 200-914-000SHEET 01

800-889-0661
DRAFT
SVL 07-05-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 157 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM
PART NUMBER DESCRIPTION QTY
NO.
ECN REV. DESCRIPTION DATE DRAWN ENG

800-889-0661
1 201-983-000 ELEMENT 1
00 INITIAL RELEASE 06-01-05 WRS WRS 2 1042-8101 PLUG 1
3 1042-8110 STRAIN RELIEF - AMPHENOL 1
5815 01 ADDED 5200-0198, 1043-0310 & 1043-0217 07-29-09 RF KAC
D 4 1043-0217 SO CORD 14-3 26" D
5 5200-0198 PVC COATED FIBERGLASS SLEEVING 11"
6 1043-0310 HEAT SHRINK 2"

1
SHT
NOTE: ITEM 6 NOT SHOWN
WIRE LIST

01
PINOUT WIRE

REV
COLOR AWG LENGTH FUNCTION
PLUG 1 #
A BLU/WHT L1 14 38" 120VAC
B BLU/WHT L2 14 38" 120VAC
3 2
C GRN/WHT PE 14 38" GROUND

202-733-000
4
C

DWG
NO.
B

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

6/1/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED WRS 6/1/2005

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN WRS 6/1/2005
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 ELEMENT AS. - BOLT-ON 18" (EZIV)
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER WRS 6/1/2005

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-733-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 158 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-600-650 18" BOLT - ON WD. - (BERM) 1

800-889-0661
6229 00 INITIAL RELEASE 02-28-2011 RJM 2 202-600-640 18" BOLT -ON AS. - LOWER (BERM) 1
3 1048-3240 WASHER - FLAT - 3/4" SAE 2
4 202-600-570 SCREW AS. - ATTACK - 12" (BERM) 1
D 14 16 17 D
5 1048-2450 NUT - JAM - 3/4"-16 2
15 14 13
6 4204-0113 JACK AS. - ATTACK (SHORT) 1
7 1048-9020 PIN - CLEVIS 2

1
8 1048-9040 KEY - COTTER 2

SHT
9 4207-0002 BODY WD. - JACK (BERM) 1

00+
10 4207-0001 SCREW AS. - JACK (BERM) 1

REV
11 300-700-100 JUNCTION BOX AS. 1
12 1049-1030 FITTING - GREASE (STR) 1
13 1048-3230 WASHER - FLAT - 5/8" SAE 2
14 1048-3382 WASHER - LOCK - 5/8" 4
24 23 22 15 1048-2090 NUT - HEX - 5/8"-11 2

202-600-600
16 1048-2430 NUT - JAM - 5/8"-11 2
17 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 2
C 4 3 5 18 1048-1140 BOLT - HEX - 3/8-16 * 1 1/2" 1
19 1048-3090 WASHER - FLAT - #10 SAE 4
20 1048-3310 WASHER - LOCK 4
1
21 1048-6995 BOLT - BUTTON HEAD - 10-32 X .5" 4
22 1048-3220 WASHER - FLAT - 1/2" SAE 4
23 1048-3370 WASHER - LOCK - 1/2" 4

DWG
NO.
24 1048-2065 NUT - HEX - 1/2-13 4

18

10 8
6 7
B
11

12

21 20 19

2
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

RJM
DATE

02-28-2011
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 02-28-2011
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE 18" BOLT - ON GP. - (BERM)
5. DO NOT SCALE DRAWING
DESIGN KAC 02-28-2011
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 02-28-2011
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 210.13
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 202-600-600 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 159 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED Default/
ITEM NO. PART NUMBER DESCRIPTION
QTY
ECN REV. DESCRIPTION DATE DRAWN ENG
1 202-600-660 18" BOLT ON LOWER WELDMENT - (BERM) 1

800-889-0661
6229 00 INITIAL RELEASE 02-28-2011 RJM
2 202-600-541 PLATE- 12" LOWER BOLT -ON COVER - RH 1
3 202-600-542 PLATE - 12" LOWER BOLT - ON COVER - LH 1
D 4 202-506-000 ELEMENT AS. 1 D
5 202-508-000 ELEMENT AS. 1
6 1003-0106 PLATE 4

1
7 1048-3330 WASHER - LOCK - 5/16" 4

SHT
8 1048-1584 BOLT - HEX 4
9 1048-3411 BOLT - FHCS - 5/16 - 18 * 1" 4

00+
REV
202-600-640
8

C
7

6 4
9

DWG
NO.
2

B 1

5
A
3
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN
APPROVALS

RJM
DATE

02-28-2011
CARLSON
PAVING PRODUCTS, INC.
A

3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 02-28-2011
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE 18" BOLT -ON AS. - LOWER (BERM)
5. DO NOT SCALE DRAWING
DESIGN RJM 02-28-2011
EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 02-28-2011
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 48.7360
.XX
.XXX =
= 0.03
0.01 FINISH = 25 B 202-600-640 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 160 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-917-000 02 BOLT ON AS. - LOWER (24) (LH)
2 1 200-974-000 00 BOLT ON AS. - UPPER (24) (LH)
D
D

800-889-0661

C
2 C

B B

1
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON GP - (24) (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE EZIV
APPROVALS DATE
DESIGN
RAJ 11-10-00 SIZE DWG. NO. REV.
A 200-432-000 00

800-889-0661
DRAFT
RAJ 11-10-00 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 161 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-870-000 BOLT ON WD - LOWER (24) (LH) 1

800-889-0661
00 INITIAL RELEASE 08-04-00 SVL 2 1003-0106 PLATE 3
6035 01 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 3 1048-3330 WASHER - LOCK - 5/16" 3
4 1048-1584 BOLT - HEX 3
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4
7 1048-3360 WASHER - LOCK 2

1
8 1048-1260 BOLT - HEX - 1/2-13 * 2" 2

SHT
9 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2

01
10 202-732-000 ELEMENT AS. - BOLT-ON 24" (EZIV) 1
4 3 2

REV
200-917-000
C

10
6 9

DWG
NO.
5

7
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SVL 08-04-00
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOLT ON AS. - LOWER (24) (LH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 60.61
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-917-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 162 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-165-000 04 BOLT ON WD - UPPER (24) (LH)
2 4 1048-3221 WASHER
D 4 3 2 3 4 1048-3370 WASHER - LOCK
D

800-889-0661
4 4 1048-2070 NUT - HEX

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - UPPER (24) (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
RAJ 09-15-03 SIZE DWG. NO. REV.
A 200-974-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 163 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-975-000 00 BOLT ON AS. - UPPER (24) (RH)
2 1 200-916-000 02 BOLT ON AS. - LOWER (24) (RH)
D
D

800-889-0661

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON GP - (24) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN DWG. NO. REV.
SIZE
A 200-433-000 00

800-889-0661
DRAFT
RAJ 11-10-00 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 164 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-166-000 04 BOLT ON WD - UPPER (24) (RH)
2 4 1048-3221 WASHER
D 3 4 1048-3370 WASHER - LOCK
2 3 4 D

800-889-0661
4 4 1048-2070 NUT - HEX

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
BOLT ON AS. - UPPER (24) (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV
APPROVALS DATE
DESIGN
RAJ 09-15-00 SIZE DWG. NO. REV.
A 200-975-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 165 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-869-000 BOLT ON WD - LOWER (24) (RH) 1

800-889-0661
00 INITIAL RELEASE 08-04-00 SVL 2 1003-0106 PLATE 3
6035 01 ITEM #6 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 3 1048-3330 WASHER - LOCK - 5/16" 3
4 1048-1584 BOLT - HEX 3
D D
5 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 4
6 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
7 1048-3360 WASHER - LOCK 2

1
8 1048-1260 BOLT - HEX - 1/2-13 * 2" 2

SHT
9 1048-3055 WASHER - FLAT - 1/2" USS (HEAVY) 2

01
10 202-732-000 ELEMENT AS. - BOLT-ON 24" (EZIV) 1

REV
4 3 2

200-916-000
C

DWG
NO.
10

7
8
9 5
B

CARLSON
1 UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SVL 08-04-00
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOLT ON AS. - LOWER (24) (RH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 60.61
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 200-916-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 166 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM
PART NUMBER DESCRIPTION QTY
NO.
ECN REV. DESCRIPTION DATE DRAWN ENG

800-889-0661
1 201-973-000 ELEMENT - 19" 1
00 INITIAL RELEASE 05-26-05 WRS WRS 2 1042-8101 PLUG 1
3 1042-8110 STRAIN RELIEF - AMPHENOL 1
5815 01 ADDED 1043-0217, 1043-0310 & 5200-0198 07-29-09 RF KAC
D 4 1043-0217 SO CORD 14-3 26" D
5 5200-0198 PVC COATED FIBERGLASS SLEEVING 11"
6 1043-0310 HEAT SHRINK 2"

1
SHT
NOTE: ITEM 6 NOT SHOWN
WIRE LIST
PINOUT WIRE

01
COLOR AWG LENGTH FUNCTION 2

REV
PLUG 1 #
A BLU/WHT L1 14 38" 120VAC
B BLU/WHT L2 14 38" 120VAC
C GRN/WHT PE 14 38" GROUND 3

202-732-000
C
4

DWG
NO.
5

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

WRS
DATE

5/26/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED WRS 5/26/2005

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN WRS 5/26/2005
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 ELEMENT AS. - BOLT-ON 24" (EZIV)
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER WRS 5/26/2005

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = B 202-732-000 01 1 OF 1
8 .25
7 6 5 4 3 2 1

800-889-0661 Page 167 of 251

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 168 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-207-000 00 EDGER AS. - BEVELED UP (RH)
2 1 201-167-000 00 EDGER AS. - BEVELED LOW (RH)
D
D

800-889-0661

C 1 C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 12
APPROVALS DATE
DESIGN
SAS 12-07-00 SIZE DWG. NO. REV.
A 200-434-000SHEET 00

800-889-0661
DRAFT
SVL 12-07-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 169 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 4 1048-3221 WASHER
2 4 1048-3370 WASHER - LOCK
D
2 3 4 1048-2070 NUT - HEX
D
2

800-889-0661
4 1 200-992-000 01 EDGER WD - BEVELED UP (RH)
3

1
C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER AS. - BEVELED UP (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 12
APPROVALS DATE
DESIGN
RAJ 09-15-00 SIZE DWG. NO. REV.
A 201-207-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 170 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION SHEET1/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-753-000 EDGER WD - BEVELED MT (RH) 1

800-889-0661
00 INITIAL RELEASE 09-07-00 RAJ 2 200-752-000 EDGER WD - BEVELED SCRD (RH) 1
5985 01 ITEM#6 1048-9250 IS NOW 1048-9265 03-22-2010 RJM 3 200-744-000 ROD WD - ADJUSTMENT 1
6035 02 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 4 4230-9921 SPRING 1
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-9265 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/2" 1
7 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 1

1
8 1048-9262 BOLT - SHOULDER SOCKET HD - 3/8 * 3" 1

SHT
9 1048-9261 BOLT - SHOULDER SOCKET HD - 1/2 * 3" 1

02
15 14 10 1048-3220 WASHER - FLAT - 1/2" SAE 2

REV
11 1048-3145 WASHER - FLAT - 3/8" SAE 1
1 12 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
12 17
13 13 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 1
14 1048-2090 NUT - HEX - 5/8"-11 1
18 19 20 15 1048-3230 WASHER - FLAT - 5/8" SAE 1

201-167-000
16 1048-2390 NUT - JAM - 1/2-13 4
5 16 17 1048-3130 WASHER - FLAT - 5/16" SAE 1
C 18 1048-1205 BOLT - HEX - 1/2-13 * 1 3/4" 2
19 1048-3370 WASHER - LOCK - 1/2" 2
20 1048-3050 WASHER - FLAT - 1/2" USS 2

10 9

DWG
NO.
4

11 8
3

B
7

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 09-07-00
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
2 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EDGER AS. - BEVELED LOW (RH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 37.526
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 201-167-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 171 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-208-000 00 EDGER AS. - BEVELED UP (LH)
2 1 201-168-000 00 EDGER AS. - BEVELED LOW (LH)
D
D

800-889-0661

C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 12
APPROVALS DATE
DESIGN
SAS 07-05-00 SIZE DWG. NO. REV.
A 200-435-000SHEET 00

800-889-0661
DRAFT
SAS 07-05-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 172 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-991-000 01 EDGER WD - BEVELED UP (LH)
2 4 1048-3221 WASHER
D 3 4 1048-3370 WASHER - LOCK
2 D

800-889-0661
4 4 1048-2070 NUT - HEX
3
4

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER AS. - BEVELED UP (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 12
APPROVALS DATE
DESIGN
RAJ 02-05-01 SIZE DWG. NO. REV.
A 201-208-000SHEET 00

800-889-0661
DRAFT
RAJ 02-05-01 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 173 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
Default/
ITEM NO. PART NUMBER DESCRIPTION
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
QTY
ECN REV. DESCRIPTION DATE DRAWN ENG
1 200-750-000 EDGER WD - BEVELED MT (LH) 1

800-889-0661
00 INITIAL RELEASE 02-05-01 RAJ
2 200-749-000 EDGER WD - BEVELED SCRD (LH) 1
5985 01 ITEM#4 1048-9250 IS NOW 1048-9265 03-22-2010 RJM
3 200-744-000 ROD WD - ADJUSTMENT 1
6035 02 ITEM #15 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM
D 4 1048-9265 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/2" 1 D
5 4230-9921 SPRING 1
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 5

1
7 1048-9262 BOLT - SHOULDER SOCKET HD - 3/8 * 3" 1

SHT
8 1048-9261 BOLT - SHOULDER SOCKET HD - 1/2 * 3" 1
9 1048-3145 WASHER - FLAT - 3/8" SAE 1

02
10 1048-3220 WASHER - FLAT - 1/2" SAE 2

REV
11 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
12 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 1
1
13 1048-2090 NUT - HEX - 5/8"-11 1
14 1048-3230 WASHER - FLAT - 5/8" SAE 1
15 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4

201-168-000
16 1048-1260 BOLT - HEX - 1/2-13 * 2" 2
10 11 5 17 1048-3050 WASHER - FLAT - 1/2" USS 2
C 18 1048-3360 WASHER - LOCK 2
19 1048-3130 WASHER - FLAT - 5/16" SAE 1
19 12

DWG
NO.
14 7 9
13

B 3
15 6

17 18 16

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RAJ 02-05-01
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EDGER AS. - BEVELED LOW (LH)
DESIGN
5. DO NOT SCALE DRAWING
2 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
ENGINEER
THIRD ANGLE PROJECTION 7. CHAMFER OR DEBURR HOLES MAX = .010

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 37.572
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 201-168-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 174 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-209-000 00 EDGER GP - BEVELED UP (RH)
2 1 201-169-000 00 EDGER AS. - BEVELED LOW (RH)
D
D

800-889-0661

C C

B B

2 CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 18
APPROVALS DATE
DESIGN
SAS 07-05-03 SIZE DWG. NO. REV.
A 200-436-000SHEET 00

800-889-0661
DRAFT
SAS 07-05-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 175 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 4 1048-3221 WASHER
2 4 1048-3370 WASHER - LOCK
D
1 2
3 3 4 1048-2070 NUT - HEX
D

800-889-0661
4 1 200-994-000 01 EDGER WD - BEVELED UP (RH)

C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED UP (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 18
APPROVALS DATE
DESIGN
RAJ 09-15-03 SIZE DWG. NO. REV.
A 201-209-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 176 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-747-000 EDGER WD - BEVELED MT (RH) 1

800-889-0661
00 INITIAL RELEASE 07-24-00 SCT 2 200-746-000 EDGER WD - BEVELED SCRD (RH) 1
5985 01 ITEM#7 1048-9250 IS NOW 1048-9265 03-22-2010 RJM 3 200-744-000 ROD WD - ADJUSTMENT 1
6035 02 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 4 4230-9921 SPRING 1
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 5
7 1048-9265 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/2" 1

1
8 1048-9262 BOLT - SHOULDER SOCKET HD - 3/8 * 3" 1

SHT
14 15
9 1048-9261 BOLT - SHOULDER SOCKET HD - 1/2 * 3" 1

02
10 1048-3220 WASHER - FLAT - 1/2" SAE 1

REV
1 11 1048-3145 WASHER - FLAT - 3/8" SAE 2
12 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
13 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 1
6 5 14 1048-2090 NUT - HEX - 5/8"-11 1
15 1048-3230 WASHER - FLAT - 5/8" SAE 1

201-169-000
16 1048-3360 WASHER - LOCK 2
4 17 1048-3050 WASHER - FLAT - 1/2" USS 2
C 18 1048-1260 BOLT - HEX - 1/2-13 * 2" 2
19 1048-3130 WASHER - FLAT - 5/16" SAE 1

DWG
NO.
10 12 11 9
3

13 19 8

6
B 7

17

16

18

2
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SCT 07-24-00
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EDGER AS. - BEVELED LOW (RH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 48.916
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 201-169-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 177 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-210-000 00 EDGER AS. - BEVELED UP (LH)
2 1 201-170-000 00 EDGER AS. - BEVELED LOW (LH)
D
D

800-889-0661

C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 18
APPROVALS DATE
DESIGN
RAJ 07-05-00 SIZE DWG. NO. REV.
A 200-437-000SHEET 00

800-889-0661
DRAFT
RAJ 07-05-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 178 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 4 1048-3221 WASHER
2 4 1048-3370 WASHER - LOCK
D
3 2 2 3 4 1048-2070 NUT - HEX
D

800-889-0661
4 1 200-993-000 01 EDGER WD - BEVELED UP (LH)

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER AS. - BEVELED UP (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 18
APPROVALS DATE
DESIGN
RAJ 09-15-03 SIZE DWG. NO. REV.
A 201-210-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-03 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 179 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXPLODED/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-743-000 EDGER WD - BEVELED MT (LH) 1

800-889-0661
00 INITIAL RELEASE 09-07-00 RAJ 2 200-742-000 EDGER WD - BEVELED SCRD (LH) 1
5985 01 ITEM#7 1048-9250 IS NOW 1048-9265 03-22-2010 RJM 3 200-744-000 ROD WD - ADJUSTMENT 1
6035 02 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 4 4230-9921 SPRING 1
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 5
7 1048-9265 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/2" 1

1
8 1048-9262 BOLT - SHOULDER SOCKET HD - 3/8 * 3" 1

SHT
9 1048-9261 BOLT - SHOULDER SOCKET HD - 1/2 * 3" 1

02
15 14 10 1048-3220 WASHER - FLAT - 1/2" SAE 1

REV
11 1048-3145 WASHER - FLAT - 3/8" SAE 2
12 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
11 12 13 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 1
6 5 14 1048-2090 NUT - HEX - 5/8"-11 1
19 13 15 1048-3230 WASHER - FLAT - 5/8" SAE 1

201-170-000
17 16 18 16 1048-3360 WASHER - LOCK 2
17 1048-3050 WASHER - FLAT - 1/2" USS 2
C 18 1048-1260 BOLT - HEX - 1/2-13 * 2" 2
19 1048-3130 WASHER - FLAT - 5/16" SAE 1

4 9 10

DWG
NO.
1
3
8 11

7
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SCT 07-24-00
2 2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EDGER AS. - BEVELED LOW (LH)
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 48.916
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 201-170-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 180 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-211-000 00 EDGER AS. - BEVELED UP (RH)
2 1 201-171-000 00 EDGER AS. - BEVELED LOW (RH)
D
D

800-889-0661

1
C C

B B

2
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 24
APPROVALS DATE
DESIGN
SAS 07-05-00 SIZE DWG. NO. REV.
A 200-438-000SHEET 00

800-889-0661
DRAFT
SAS 07-05-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 181 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 4 1048-3221 WASHER
1 2 4 1048-3370 WASHER - LOCK
D 2 3 4 1048-2070 NUT - HEX
3 D

800-889-0661
4 1 200-996-000 01 EDGER WD - BEVELED UP (RH)

C 1 C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER AS. - BEVELED UP (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 24
APPROVALS DATE
DESIGN
SAS 09-15-00 SIZE DWG. NO. REV.
A 201-211-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 182 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXPLODED/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-756-000 EDGER WD - BEVELED MT (RH) 1

800-889-0661
00 INITIAL RELEASE 07-26-00 SCT 2 200-755-000 EDGER WD - BEVELED SCRD (RH) 1
5985 01 ITEM#7 1048-9250 IS NOW 1048-9265 03-22-2010 RJM 3 200-744-000 ROD WD - ADJUSTMENT 1
6035 02 ITEM #5 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 4 4230-9921 SPRING 1
D D
5 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 5
7 1048-9265 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/2" 1

1
15
8 1048-9262 BOLT - SHOULDER SOCKET HD - 3/8 * 3" 1

SHT
9 1048-9261 BOLT - SHOULDER SOCKET HD - 1/2 * 3" 1

02+
12 14 10 1048-3220 WASHER - FLAT - 1/2" SAE 1
16

REV
11 1048-3145 WASHER - FLAT - 3/8" SAE 2
13 11 12 1048-3130 WASHER - FLAT - 5/16" SAE 1
13 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1
14 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 1
15 1048-2090 NUT - HEX - 5/8"-11 1

201-171-000
17 16 1048-3230 WASHER - FLAT - 5/8" SAE 1
17 1048-3050 WASHER - FLAT - 1/2" USS 2
C
18 18 1048-3360 WASHER - LOCK 2
19 19 1048-1260 BOLT - HEX - 1/2-13 * 2" 2

10 9

DWG
NO.
8

3
4

5 6

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SCT 07-26-00
2 2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE EDGER AS. - BEVELED LOW (RH)
DESIGN
5. DO NOT SCALE DRAWING 24"
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 61.959
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 201-171-000 02+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 183 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 201-212-000 00 EDGER AS. - BEVELED UP (LH)
2 1 201-172-000 00 EDGER AS. - BEVELED LOW (LH)
D
D

800-889-0661

C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER GP - BEVELED (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 24
APPROVALS DATE
DESIGN
SAS 07-05-00 SIZE DWG. NO. REV.
A 200-439-000SHEET 00

800-889-0661
DRAFT
SAS 07-05-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 184 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 4 1048-3221 WASHER
2 4 1048-3370 WASHER - LOCK
D
3 2 1 3 4 1048-2070 NUT - HEX
D

800-889-0661
4 1 200-995-000 01 EDGER WD - BEVELED UP (LH)

C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
EDGER AS. - BEVELED UP (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE
EZIV 24
APPROVALS DATE
DESIGN
RAJ 09-15-00 SIZE DWG. NO. REV.
A 201-212-000SHEET 00

800-889-0661
DRAFT
RAJ 09-15-00 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2
Page 185 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 200-758-000 EDGER WD - BEVELED MT (LH) 1

800-889-0661
00 INITIAL RELEASE 07-26-00 SCT 2 200-757-000 LH 24" BEV EDGER SCREED 1
5985 01 ITEM#5 1048-9250 IS NOW 1048-9265 03-22-2010 RJM 3 200-744-000 ROD WD - ADJUSTMENT 1
6035 02 ITEM #17 1048-1250 WAS REPLACED WITH 1048-1324 05-26-2010 RJM 4 4230-9921 SPRING 1
D D
5 1048-9265 BOLT - SHOULDER SOCKET HD - 5/8 * 1 1/2" 1
6 1048-2260 NUT - LOCK - 1/2"-13 TOPLOCK 5
7 200-002-150 ARM WD - DEPTH SCREW (LH) 2

1
8 1048-3360 WASHER - LOCK 2

SHT
9 1048-1260 BOLT - HEX - 1/2-13 * 2" 2
14 16 12 15

02
10 1048-9262 BOLT - SHOULDER SOCKET HD - 3/8 * 3" 1
17 6

REV
11 1048-9261 BOLT - SHOULDER SOCKET HD - 1/2 * 3" 1
18 19 1
12 1048-3145 WASHER - FLAT - 3/8" SAE 2
13 1048-3220 WASHER - FLAT - 1/2" SAE 1
14 1048-3130 WASHER - FLAT - 5/16" SAE 1
15 1048-2240 NUT - LOCK - 3/8"-16 TOPLOCK 1

201-172-000
16 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 1
17 1048-1324 BOLT - SQHSS - 1/2 - 13 * 2" 4
C 18 1048-3230 WASHER - FLAT - 5/8" SAE 1
19 1048-2090 NUT - HEX - 5/8"-11 1

11 13

DWG
NO.
10

B
5
6

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN SCT 07-26-00
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
? 8 9 ASME Y14.3M-1994
4. APPLICATION OF ENGINEERING DRAWINGS PER
CHECKED
TITLE EDGER AS. - BEVELED LOW (LH)
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 205.652
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 201-172-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 186 of 251

Typical Cut-Off Shoe Installation.

DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661

Page 187 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-759-000 01 SHOE AS.- CUTOFF (LH)
2 1 200-760-000 00 PLATE
D 3 3 1048-2070 NUT - HEX
D

800-889-0661
4 3 1048-3360 WASHER - LOCK
5 3 1048-3220 WASHER
6 2 1048-1240 BOLT - HEX
7 4 1048-4170 SCREW - SET
8 4 1048-2430 NUT - JAM
9 4 1048-3380 WASHER - LOCK

3
4
5
C 7 C
2

8
9

1
B B

5 6
3
4

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
SHOE AS. - CUTOFF (6") (LH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE

APPROVALS DATE
DESIGN
RAJ 03-19-01 SIZE DWG. NO. REV.
A 200-764-000SHEET 00

800-889-0661
DRAFT
RAJ 03-19-01 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 188 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-762-000 00 SHOE AS. - CUTOFF (RH)
2 1 200-760-000 00 PLATE
D 3 3 1048-2070 NUT - HEX
D

800-889-0661
4 3 1048-3360 WASHER - LOCK
5 3 1048-3220 WASHER
6 2 1048-1240 BOLT - HEX
7 7 4 1048-4170 SCREW - SET
8 4 1048-2430 NUT - JAM
9 4 1048-3380 WASHER - LOCK
3
2 4
8
5
C
9
C

3
4
6
5

B 1 B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
SHOE AS. - CUTOFF (6") (RH)

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE

APPROVALS DATE
DESIGN
RAJ 03-19-01 SIZE DWG. NO. REV.
A 200-765-000SHEET 00

800-889-0661
DRAFT
RAJ 03-19-01 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 189 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 200-760-000 00 PLATE
2 1 1048-2070 NUT - HEX
D 3 1 1048-3360 WASHER - LOCK
D

800-889-0661
4 1 1048-3220 WASHER
5 1 200-761-000 00 SHOE AS.- EXTENSION
6 1 1048-0540 SCREW - CAP

C C
2
3 1
4

B B

5
6

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A A
SHOE EXT. - CUTOFF (6")

DynapacParts.com
CAD GENERATED DRAWING,
DO NOT MANUALLY UPDATE

APPROVALS DATE
DESIGN
RAJ 03-19-01 SIZE DWG. NO. REV.
A 201-327-000SHEET 00

800-889-0661
DRAFT
RAJ 03-19-01 SCALE CAD FILE: 1 OF 1
8 7 6 5 4 3 2 1
Page 190 of 251
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 202-569-100 00 SHOE AS. - CUTOFF (12") (LH)
2 1 202-569-002 00 PLATE
D 3 4 1048-2070 NUT - HEX
D

800-889-0661
4 4 1048-3360 WASHER - LOCK
5 4 1048-3220 WASHER
6 2 1048-1240 BOLT - HEX
7 4 1048-4170 SCREW - SET
8 4 1048-2430 NUT - JAM
9 4 1048-3380 WASHER - LOCK

3
2 4
C 1 5 7 C

B B

CARLSON PAVING PRODUCTS INC.

6 18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A 5 CAD GENERATED DRAWING, A
4 DO NOT MANUALLY UPDATE SHOE GP - CUTOFF (12") (LH)

DynapacParts.com
3 APPROVALS DATE
DESIGN
WAD 031203
MODEL
WAD 061203 SIZE DWG. NO. REV.
A 202-569-000 00

800-889-0661
DRAFT
WAD 061203 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 191 of 251 1-1
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 202-570-100 00 SHOE AS. - CUTOFF (12") (RH)
2 1 202-569-002 00 PLATE
D 3 4 1048-2070 NUT - HEX
D

800-889-0661
4 4 1048-3360 WASHER - LOCK
5 4 1048-3220 WASHER
6 2 1048-1240 BOLT - HEX
7 4 1048-4170 SCREW - SET
8 4 1048-2430 NUT - JAM
9 4 1048-3380 WASHER - LOCK
10 2 1048-0540 SCREW - CAP

C 7 4
C
5
1
8

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
6 DO NOT MANUALLY UPDATE SHOE GP - CUTOFF (12") (RH)

5
DynapacParts.com
APPROVALS DATE
DESIGN
WAD 061203
4 3 MODEL
WAD 061203 SIZE DWG. NO. REV.
A 202-570-000 00

800-889-0661
DRAFT
WAD 061203 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 192 of 251 1-1
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 202-569-002 00 PLATE
2 2 1048-2070 NUT - HEX
D 3 2 1048-3360 WASHER - LOCK
D

800-889-0661
4 2 1048-3220 WASHER
5 1 202-571-100 00 SHOE AS. - EXTENSION (12")

2
3
5 4
C C
1

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE SHOE GP - EXTENSION (12")

DynapacParts.com
APPROVALS DATE
DESIGN
WAD 061203
MODEL
WAD 061203 SIZE DWG. NO. REV.
A 202-571-000 00

800-889-0661
DRAFT
WAD 061203 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 193 of 251 1-1
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-868-100 12" SHOE WD. - CUTOFF (RH) 1

800-889-0661
5241 00 INITIAL RELEASE 06-11-07 MSOU 2 1048-2070 NUT - HEX - 1/2"-13 4
3 1048-3360 WASHER - LOCK 4
4 1048-3220 WASHER - FLAT - 1/2" SAE 4
D D
5 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2
6 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 4
7 1048-2430 NUT - JAM - 5/8"-11 4

1
8 1048-3380 WASHER - LOCK 4

SHT
9 202-569-002 PLATE 1

00+
6

REV
7

202-868-000
C

DWG
NO.
2
3
B 4

1
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN MSOU 06-11-07
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 06-12-07
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE 12" SHOE AS- CUTOFF (VOGELE) (RH)
DESIGN MSOU 06-11-07
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 06-11-07

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = B 202-868-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 194 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-869-100 12" SHOE WD.- CUTOFF (LH) 1

800-889-0661
5241 00 INITIAL RELEASE 06-11-07 MSOU 2 1048-2070 NUT - HEX - 1/2"-13 4
3 1048-3360 WASHER - LOCK 4
4 1048-3220 WASHER - FLAT - 1/2" SAE 4
D D
5 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2
6 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 4
7 1048-2430 NUT - JAM - 5/8"-11 4

1
8 1048-3380 WASHER - LOCK 4

SHT
9 202-569-002 PLATE 1

00+
REV
2

202-869-000
3
C
6
4

9 7
5

DWG
NO.
8

1
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN MSOU 06-11-07
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 06-12-07
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE 12" SHOE AS - CUTOFF (VOGELE) (LH)
DESIGN MSOU 06-11-07
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 06-12-07

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = B 202-869-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 195 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG
1 203-332-100 SHOE AS. - CUTOFF WD. (12") (RH) ROADTEC 1

800-889-0661
5510 00 INITIAL RELEASE 09-12-08 RJM
2 202-569-002 PLATE 1
3 1048-2070 NUT - HEX - 1/2"-13 4
D
4 1048-3360 WASHER - LOCK 4 D
5 1048-3220 WASHER - FLAT - 1/2" SAE 4
6 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2

1
7 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 4

SHT
8 1048-2430 NUT - JAM - 5/8"-11 4
9 1048-3380 WASHER - LOCK 4

00+
REV
203-332-000
C

7 3 4 5

1 9

DWG
NO.
2

3 4 5 6

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 9-12-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SHOE GP - CUTOFF (12") (RH) ROADTEC
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 69.775
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 203-332-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 196 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-333-100 SHOE - CUTOFF WD. (12") (LH) ROADTEC 1

800-889-0661
5510 00 INITIAL RELEASE 09-12-08 RJM 2 202-569-002 PLATE 1
3 1048-2070 NUT - HEX - 1/2"-13 4
4 1048-3360 WASHER - LOCK 4
D D
5 1048-3220 WASHER - FLAT - 1/2" SAE 4
6 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2
7 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 4

1
8 1048-2430 NUT - JAM - 5/8"-11 4

SHT
9 1048-3380 WASHER - LOCK 4

00+
REV
9 8 7

203-333-000
C 3 4 5

DWG
NO.
B 1

6 5 4 3

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 9-12-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SHOE GP - CUTOFF (12") (LH) ROADTEC
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 69.775
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 203-333-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 197 of 251

 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 202-678-100 00 SHOE AS. - CUTOFF (RH)
3 2 1 202-678-001 00 PLATE
D 3 4 1048-2070 NUT - HEX
D
4
800-889-0661
4 4 1048-3360 WASHER - LOCK
5 4 1048-3220 WASHER
6 2 1048-1240 BOLT - HEX
5 7 4 1048-4170 SCREW - SET
8 4 1048-2430 NUT - JAM
9 4 1048-3380 WASHER - LOCK
1

2
C C

5 4 3

7 B
B

6
CARLSON PAVING PRODUCTS INC.
18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE SHOE AS. - CUTOFF (24") (RH)

DynapacParts.com
APPROVALS DATE
DESIGN

MODEL SIZE DWG. NO. REV.

A 202-678-000 00

800-889-0661
DRAFT
RAJ 09-13-04 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 198 of 251 1-1
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 202-679-100 00 SHOE AS.- CUTOFF (LH)
2 1 202-678-001 00 PLATE
D 3 4 1048-2070 NUT - HEX
D

800-889-0661
4 4 1048-3360 WASHER - LOCK
5 4 1048-3220 WASHER
6 2 1048-1240 BOLT - HEX
3 7 4 1048-4170 SCREW - SET
8 4 1048-2430 NUT - JAM
9 4 1048-3380 WASHER - LOCK
4
1
5 2 7
C C
8
9

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE SHOE AS. - CUTOFF (24") (LH)

DynapacParts.com
APPROVALS DATE
DESIGN
RAJ 03-19-01
3 4 5 6 MODEL SIZE DWG. NO. REV.
A 202-679-000 00

800-889-0661
DRAFT
RAJ 03-19-01 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 199 of 251 1-1
 8 7 6 5 4 3 2 1
NOTES: # QTY PART # REV DESCRIPTION

DynapacParts.com
1 1 202-680-100 00 SHOE AS. - EXTENSION (24")
2 1 202-678-001 00 PLATE
D 3 2 1048-2070 NUT - HEX
D

800-889-0661
4 2 1048-3360 WASHER - LOCK
5 2 1048-3220 WASHER
1
3

4
5
2
C C

B B

CARLSON PAVING PRODUCTS INC.

18425 50TH Ave E. Tacoma, WA 98446
ph (253) 875-8000 fx (253) 846-0100
A CAD GENERATED DRAWING, A
DO NOT MANUALLY UPDATE SHOE GP - EXTENSION (24")

DynapacParts.com
APPROVALS DATE
DESIGN

MODEL SIZE DWG. NO. REV.

A 202-680-000 00

800-889-0661
DRAFT
RAJ 09-13-04 SCALE CAD FILE: SHEET 1 OF 1
8 7 6 5 4 3 2
Page 200 of 251 1-1
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-679-200 SHOE WD - CUTOFF (24") (LH) HEATED END GATE 1

800-889-0661
2 202-750-001 PLATE ADJUSTMENT BRACKET CUTOFF SHOE HEATED 1
3 1048-2070 NUT - HEX 4
4 1048-3360 WASHER - LOCK 4
D D
2 5 1048-3220 WASHER 4
6 1048-1240 BOLT - HEX 2

1
7 1048-4170 SCREW - SET 4
2X 5 4 3

SHT
8 1048-2430 NUT - JAM 4
1 9 1048-3380 WASHER - LOCK 4

REV
202-750-000
C 7 8 9 4X

DWG
NO.
B

6 5 4 3 2X

NOTES:
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS DATE
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 SHOE AS. - CUTOFF (24") (LH)
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-750-000 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 201 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2005 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 202-678-200 SHOE WD - CUTOFF (24") (RH) HEATED END GATE 1

800-889-0661
00 INITIAL RELEASE 11/14/2005 PGM 2 202-750-001 PLATE ADJUSTMENT BRACKET CUTOFF SHOE HEATED 1
3 1048-2070 NUT - HEX 4
4 1048-3360 WASHER - LOCK 4
D D
5 1048-3220 WASHER 4
6 1048-1240 BOLT - HEX 2

1
7 1048-4170 SCREW - SET 4
4X 5 4 3

SHT
8 1048-2430 NUT - JAM 4
9 1048-3380 WASHER - LOCK 4

00
REV
1
2

7X 9 8 7

202-751-000
C

DWG
NO.
B

NOTES:
A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

PGM
DATE

11/12/2005
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE
ASME Y14.24-1999 DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030 SHOE AS. CUTOFF (24") (RH)
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER PLM 11/12/2005

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH =
.25 B 202-751-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 202 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-334-100 SHOE - CUTOFF WD. (24") (RH) ROADTEC 1

800-889-0661
5510 00 INITIAL RELEASE 09-12-08 RJM 2 202-678-001 PLATE 1
3 1048-2070 NUT - HEX - 1/2"-13 4
4 1048-3360 WASHER - LOCK 4
D D
5 1048-3220 WASHER - FLAT - 1/2" SAE 4
6 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2
7 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 4

1
8 1048-2430 NUT - JAM - 5/8"-11 4

SHT
9 1048-3380 WASHER - LOCK 4

00+
REV
5 4 3

203-334-000
C

DWG
NO.
3 4 5 6

9 8 7

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 9-12-2008
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SHOE AS. - CUTOFF (24") (RH) ROADTEC
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 121.416
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 203-334-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 203 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION EXP/QTY.
ECN REV. DESCRIPTION DATE DRAWN ENG 1 203-335-100 SHOE - CUTOFF WD. (24) (LH) ROADTEC 1

800-889-0661
5510 00 INITIAL RELEASE 09-12-08 RJM 2 202-678-001 PLATE 1
3 1048-2070 NUT - HEX - 1/2"-13 4
4 1048-3360 WASHER - LOCK 4
D D
5 1048-3220 WASHER - FLAT - 1/2" SAE 4
6 1048-1240 BOLT - HEX 1/2-13 * 1 1/2 2
7 1048-4170 BOLT - SQHSS - 5/8 - 11 * 3 1/2" 4

1
8 1048-2430 NUT - JAM - 5/8"-11 4

SHT
9 1048-3380 WASHER - LOCK 4

00+
REV
203-335-000
9 8 7

5 4 3
1
2

DWG
NO.
B

6 5 4 3
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RJM 9-12-08
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE SHOE AS. - CUTOFF (24") (LH) ROADTEC
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 121.416
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 203-335-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 204 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 305-501-100 BOX AS. - CONTROL (LH) 1

800-889-0661
5861 00 INITIAL RELEASE 10-02-09 RF KAC 2 305-501-200 BOX AS. - CONTROL (RH) 1
6062 01 CHANGED DRAWING ONLY 6/25/2010 RF KAC 3 305-880-000 HARNESS AS. - VALVES (LH) 1
4 305-881-000 HARNESS AS. - VALVES (RH) 1
D D
5 305-560-000 CABLE AS. - CROSSOVER 1
6 305-540-000 CABLE AS. - TRACTOR (RH) 1
7 305-501-300 REMOTE AS. - (RH) 1

1
8 305-501-400 REMOTE AS. - (LH) 1

SHT
01
REV
5
8 3

305-501-000
1 6
C
4

DWG
NO.
B

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 10-02-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 10-02-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE DC ELECTRICAL GROUP
DESIGN RF 10-02-09
5. DO NOT SCALE DRAWING DYNAPAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 10-02-09 WITH MOBA

DynapacParts.com
8. TOLERANCES:
SIMILAR 305-500-000 MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 63.21
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 305-501-000 01 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 205 of 251

 8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED

23 RH CONVEYOR STOP

26 RH AUGER REVERSE
21 LH AUGER REVERSE
18 LH CONVEYOR STOP

22 RH CONVEYOR RUN
17 LH CONVEYOR RUN
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR

8 RH TOW POINT DN
7 RH TOW POINT UP
6 LH TOW POINT DN
5 LH TOW POINT UP

25 RH AUGER STOP
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING

20 LH AUGER STOP

24 RH AUGER RUN
19 LH AUGER RUN
PRODUCTS, INC. ALL RIGHTS RESERVED.

16 E-STOP OUT
11 RH EXT OUT
10 LH EXT OUT

13 A/C POWER
12 RH EXT IN

15 E-STOP IN
9 LH EXT IN

29 RH MOBA
28 LH MOBA
14 HORN
+24V
+24V
3 GND
4 GND

27

30
31
202-538-000

2
1042-8026
1042-0348
1042-8027

20 20

30 30
31 31
21 21
22 22
23 23
24 24
25 25
26 26
27 27
28 28
10 10
11 11
12 12
13 13
14 14
15 15
16 16
17 17
18 18
19 19

29 29
RIGHT CONTROL BOX

1
2
3
4

6
7
8
9
5
D D

1
2
3
4

6
7
8
9
5
LEFT CONTROL BOX 1042-0352

1042-8026
1042-0348

931
939

928

934
911

942

932
913

929

935
938
304

941

860
119
200

850
118

200

719

720
718

809
808
721

806
807

861
DynapacParts.com
118 1 1 118

2
1 1
119 119
2 2 2 2
200 200
3 3 3 3

SHT
MANUAL SPARE 850
939 4 4 4 4
718 718
3 5 5 5 5
850 2 719 719

01
6 6 6 6

800-889-0661
UP 938 939 939
1 7 7 7 7
718 938 938
CONVEYOR

REV
1 8 8 8 8
2 1044-0115 OFF 806 806
200 9 9 9 9
807 807
719 10 10 10 10
3 929 929
11 11 11 11
DOWNTOWPOINT 928 928
1044-0115 12 12 12 12
MANUAL 935 935
13 13 13 13 912 1 2 913
304 304
14 14 14 14
OFF 911 MANUAL
929 928 911
15 15 15 15 942 E-STOP
850 912 912 3
16 16 16 16 1044-0157
AUTO 3 1 1 2 850 2
912 900 900
911 17 17 17 17
860 2 941
SPARE

305-501-000
SPARE 18 18 1
1 AUGER 18 18 UP
2 850 E-STOP SPARE
1044-0115 SPARE 721 OFF
1044-0157 19 19 19 19
850 SPARE 1 CONVEYOR
2 20 20 200 2 AUTO
3 929A 850 20 20 1044-0115

1042-0520

1042-0348

1042-0520
1042-0348
935 LEFT REMOTE RIGHT REMOTE 860
939A 119
1 720 1
3 850 2
1044-0114 2 304

931
932
929
REVERSE 1

928
119 119 DOWN
1044-7001 A A TOWPOINT OFF MANUAL
C OVER RIDE HORN
1044-7001 928
B
AUGER
A A
932 1044-0115
931 932
3
B 1044-0115 AUGER B B 942A
929 2 931
C C
1
2
3 1044-0115 3 1
C C 1044-0114
200 OFF 200
D D OVER RIDE OVER RIDE 850 OFF D D 1 3 932A
850 850 AUGER
UP 850 2 OVER RIDE
E E UP E E 1044-0115
718
F F 1 2 200 2 1 721 F F 850
200
718 721
G G G G
719 3 720
719 3 720
H H TOWPOINT H H
806 DOWN 1044-0115 TOWPOINT DOWN 808
J J J J
1044-0115 2 850
807 809
K K K K
UNLOCK
L L 807 806 934
807 806 808 809 L L 402 400 1

DWG
1

808

809

NO.
M M M M
2 3 3 2 1
OUT 1 2 IN IN REVERSE
N N OUT N N
OUT IN 1044-7001
3 3 1 P P P P IN 1 3 OUT
1044-0209 2 EXTENSION 119 119 EXTENSION 2
BERM/SLOPE LOCK 1044-0115 1044-0115 119
118

118
(OPTIONAL) EXTENSION EXTENSION 2
1044-0115 1044-0115 304

1042-0521

1042-0358
1042-8024
1042-0357
1

HORN
1044-7001
411 SLOPE DN SLOPE DN 410
A A A A
407 HEIGHT DN HEIGHT DN 406
B B B B
UP 403 EXT OUT EXT OUT 400 UNLOCK
C C C C UP
401 EXT IN EXT IN 402 408
409 1
2 1 D D D D 1
405 HEIGHT UP HEIGHT UP 404 2
E E E E 2 118

F F F F 410
411 3
3
DOWN G G G G 3
B SLOPE 409
H H
SLOPE UP SLOPE UP
H H
408 DOWN LOCK
1044-0209
B
1044-0116 SLOPE
CROWN UP 418 1044-0116 BERM/SLOPE
J J J J
CROWN DN 416 (OPTINAL)
K K K K
UP
L L L L UP
405 404
M M M M
1 1
118 2 N N N N 118
UP
O O 418 2
O O 406
407 1
HEAT P P 3
3 P P 118
DOWN
502 87A Q Q Q Q 2 DOWN HEIGHT
HEIGHT 416 1044-0116
1044-0116 2 1 30 87 R R R R 3
S S S S 1 3 DOWN CROWN
85 86 1044-0116
T T T T MIN MAX 1 3
300-137-000
OFF U U U U 2 MIN MAX
HEAT
1044-0113 V V 2
RELAY V V
1044-0170 W W
W W
X X X X
1042-8050

DynapacParts.comA
B
C
D TO GENERATOR
A B C D E F G H J A B C D E F G H J A B C D E F G H J A B C D E F G H J

800-889-0661
1 3
1 3

CARLSON
E
MIN MAX MAX
MIN F
2 2
A G A
H

J PAVING PRODUCTS, INC.

1042-8020
1042-8022

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE DC ELECTRICAL GROUP
C

B
C

B
DYNAPAC
A A WITH MOBA
SNAP SWITCH SIZE DRAWING NUMBER REV SHEET:
A B C D E F G H J A B C D E F G H J A B C D E F G H J A B C D E F G H J
B 305-501-000 01 2 OF 2
8 7 6 5 4 3 2 1
Page 206 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
1 305-501-101 ELECTRICAL BOX - LAYOUT 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 300-127-400 FACE PLATE - LH 1

800-889-0661
5861 00 INITIAL RELEASE 10-02-09 RF KAC 3 300-069-000 TUBE, STANDOFF 4
6018 01 CHANGED AUGER AND CONVEYOR WIRING 04-28-10 RF KAC 4 1044-7001 SWITCH - TOGGLE 1NT1-6 2
5 1044-0209 SWITCH - TOGGLE 1NT1-3 1
6062 02 DELETED 1044-0122 AND ADDED 1044-0115 X 2, 1042-9118 6/25/2010 RF KAC
6 1044-0115 SWITCH - TOGGLE 1NT1-7 4
D D
7 1044-0116 SWITCH - TOGGLE 1NT1-7E 2
8 300-137-000 LIGHT AS. LED 1
25 26 9 1042-0383 CONNECTOR - CORD RANGE .250 - .375 1

1
10 1042-0184 NUT - LOCK 1/2" (PIPE) 1
11 1042-0187 1/2" PLASTIC BUSHING 1

SHT
30
12 1044-0170 RELAY - 24V 1
13 1048-0350 BOLT - STR. BIT PAN HD - 10 - 32 * 4 1/2" 4

02
14 1048-1830 BOLT - PAN HD PHILLIPS - 10 - 32 * 3/4" 1

REV
23 15 1048-3520 WASHER - EXT STAR - #10 5
16 1048-3100 WASHER - FLAT - #10 SAE 5
17 1048-2015 NUT - ACORN - #10-32 (SS) 1
18 300-399-000 PLATE - DEUTSCH SIZE 18 LOCK 1
9 19 300-400-000 PLATE - DEUTSCH 24 SHELL SIZE LOCK 2
24 20 1043-0090 428-2-VC NICROPRESS SLEEVE 1
21 1043-0349 CABLE STOP - DOUBLE 2

305-501-100
19
22 1043-0348 3/64" SS NYLON CABLE 18"
23 305-870-000 JACK AS. - VALVES (LH) 1
41 39 38 40 24 305-873-000 JACK AS.- GENERATOR 1
C
10 25 305-571-000 JACK AS. - CROSSOVER 1
26 300-188-000 CABLE AS. 3-PIN LADD 1
27 1044-0157 CONTACT BLOCK - (1) NC 1
17 15 16 14 44 28 1044-0158 PUSHBUTTON HEAD 1
5 29 97944-04 HOLE - PLUG (1/2") 1
30 305-872-500 JACK AS. - REMOTE 1
31 1044-0333 DIODE - 6 AMP 2

DWG
32 1048-3145 WASHER - FLAT - 3/8" SAE 4

NO.
36 8
33 1048-2053 NUT - HEX - 3/8"-16 NYLOCK 2
34 1048-1131 BOLT- HEX - 3/8-16 * 1 1/4" 2
35 1042-9064 CONTROLLER-MOBA 2
43 36 1042-9065 REOSTAT 2
37 1044-0460 KNOB, BLACK 2
38 1048-3085 WASHER - FLAT - #8 SAE 8
27 39 1048-3515 WASHER - STAR (EXTERNAL) - #8 4
40 1048-2007 NUT- HEX 4
28 41 1048-1816 BOLT - PAN HEAD PHILLIPS - #8-32 * 5/8" 4
B
42 1044-7020 CAP -RED 9
12 43 1044-0114 SWITCH - TOGGLE 1NT1-5 1
44 1042-9118 CAP, FLANGED 4
29
NOTE: ITEM 20, 21, 22, 31 AND 42 ARE NOT SHOWN.
7 6

7 3

6 18 34 33 32 35
1
11
6
37
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
4 4 INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN RF 10-02-09
PAVING PRODUCTS, INC.
6 2 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED KAC 10-02-09
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOX AS. - CONTROL (LH)
DESIGN RF 10-02-09
5. DO NOT SCALE DRAWING DYNAPAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 10-02-09

DynapacParts.com
8. TOLERANCES:
13 15 16 SIMILAR
TO
305-500-100 .X = 0.10 ANGULAR = 0 30' MATERIAL: SIZE DRAWING NUMBER REV SHEET:

WT. 24.72
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 305-501-100 02 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 207 of 251

 A
B
C
D

8
8

LEFT CONTROL BOX

1042-8026
1042-0348
PRODUCTS, INC. ALL RIGHTS RESERVED.

118
1 1
119
2 2
200
3 3
MANUAL SPARE
939 4 4
3 718
5 5
850 2 719
6 6
UP 938 939
1 7 7
718 938
1 CONVEYOR 8 8
2 1044-0115 OFF 806
200 9 9
7

7
807
719 10 10
3 929
11 11
DOWNTOWPOINT 928
1044-0115 12 12
MANUAL 935
13 13
304
14 14
OFF 911
929 928
15 15
850 912
16 16
AUTO 3 1 1 2 900
911 912 17 17
860 2
SPARE
1 AUGER 18 18
2 850 E-STOP
1044-0115 SPARE
1044-0157 19 19
850
3 929A 850 2 20 20
935
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING

939A 119
1
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.

6
6

1044-0114 2 304
REVERSE 1
1042-0520
1042-0348

119
1044-7001 A A
OVER RIDE HORN
1044-7001 928
B B
929
C C
200
D D
850
E E
F F
718
G G
719
H H
806 J J
807
K K
UNLOCK
L L
807 806
1 M M
2
5

5
N N
3 OUT 3 1 IN P P
1044-0209 2
BERM/SLOPE LOCK
118

(OPTIONAL) EXTENSION
1044-0115
1042-0357

411
A
407
403 B

Page 208 of 251

UP
401 C
409
2 1 D
405
E

411 F

4
4

3
DOWN G
SLOPE 409
H
1044-0116
J
800-889-0661
800-889-0661

K
UP
L
405
M
1
118 2 N
DynapacParts.com
DynapacParts.com

O
407
3 HEAT P
DOWN
502 87A Q
HEIGHT
1044-0116 2 1 30 87 R
S
85 86
3

T
300-137-000
3

OFF U
HEAT
1044-0113 RELAY V
1044-0170
W
X
1042-8050

A
B
TITLE

SIZE

B
C
D TO GENERATOR
1 3
1 3
E
MIN MAX MAX
MIN F
2 2
2
DYNAPAC

G
2

DRAWING NUMBER

J
1042-8022

B
305-501-100
BOX AS. - CONTROL (LH)

A B C D E F G H J A B C D E F G H J A B C D E F G H J A B C D E F G H J
REV
1

1
02
PAVING PRODUCTS, INC.
CARLSON
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

SHEET:

2 OF 2

DWG REV SHT

D

A
B

NO. 305-501-100 02 2
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1045-0236 LED 2000mcd 1

800-889-0661
00 INITIAL RELEASE 04-19-06 MP 2 300-398-000 PANEL MOUNT - LED 1
5122 01 DELETED ITEMS 1044-0350, 1045-0235, 300-178-000 AND 1043-0355; 01-08-07 MP 3 1045-0243 LENSE - PANEL MOUNT LED 1
ADDED ITEM 2 300-398-000
D 5423 02 ADDED ITEM 1045-0243 06-05-08 BRM D

1
SHT
02
REV
300-137-000
C

DWG
NO.
2

B 1

NOTES:

A
UNLESS OTHERWISE SPECIFIED
1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
DRAWN
APPROVALS

MP
DATE

04-19-06
CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

ASME Y14.3M-1994 CHECKED

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE LIGHT AS. LED
DESIGN
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
MATERIAL: SIZE DRAWING NUMBER REV SHEET:
.X = 0.10 ANGULAR = 0 30'
.XX
.XXX =
= 0.03
0.01 FINISH = 125 B 300-137-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 209 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0357 JACK - 23 PIN 1

800-889-0661
5203 00 INITIAL RELEASE 04-09-07 MP 2 1042-0353 NUT - SIZE 24 1
5225 01 CHANGED QTY OF 1042-8040 WAS 13, 202-540-000 WAS 10. ADDED ITEMS 1043-0270 05-17-07 MP 3 1042-0354 LOCK WASHER - SIZE 24 1
AND 1043-0271. UPDATED JACK WIRE LIST
4 1042-8040 CONTACT PIN SIZE 16 15
D D
5 202-540-000 SEAL- ELECTRICAL 8
6 1043-0268 WIRE - STRANDED (18AWG)(GREEN) 72"
7 1043-0267 WIRE - STRANDED (18AWG)(BROWN) 36"

1
8 1043-0265 WIRE - STRANDED (18AWG)(BLACK) 36"

SHT
9 1043-0266 WIRE - STRANDED (18AWG)(BLUE) 36"

00+
10 1043-0272 WIRE - STRANDED (18AWG)(RED) 72"

REV
11 1043-0269 WIRE - STRANDED (18AWG)(GRAY) 36"
12 1043-0273 WIRE - STRANDED (18AWG)(WHITE) 36"
13 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 36"
14 1043-0270 WIRE - STRANDED (18AWG)(ORANGE) 36"
15 1043-0271 WIRE - STRANDED (18AWG)(PURPLE) 36"

305-870-000
16 1043-0257 WIRE - STRANDED (16AWG) (BLUE) 36"
17 1043-0263 WIRE - STRANDED (16AWG) (WHITE) 36"
C 18 1043-0261 WIRE - STRANDED (16AWG) (BLACK) 36"

JACK WIRE LIST

5 4 3 2 1
PIN TERMINAL WIRE WIRE WIRE WIRE
FUNCTION

DWG
NO.
OUT USED COLOR AWG LENGTH #
A 1042-8040 RED 18 36" 411 SLOPE DOWN
B 1042-8040 BLACK 18 36" 407 HEIGHT DOWN
C 1042-8040 BROWN 18 36" 401 EXTENSION IN
D 1042-8040 GREEN 18 36" 403 EXTENSION OUT
E 1042-8040 BLUE 18 36" 405 HEIGHT UP
F 202-540-000
B G 202-540-000
H 1042-8040 GRAY 18 36" 409 SLOPE UP
J 1042-8040 ORANGE 18 36" 417 CROWN UP
K 1042-8040 PURPLE 18 36" 419 CROWN DOWN
L 1042-8040 BLUE 16 36" 421 AUGER TUNNEL IN (OPT)
M 1042-8040 WHITE 16 36" 423 AUGER TUNNEL OUT (OPT)
N 1042-8040 BLACK 16 36" 425 MANIFOLD GROUND (OPT)
O 202-540-000
P 1042-8040 RED 18 36" 427 MANIFOLD POWER (OPT)
Q 1042-8040 GREEN 18 36" 429 MANIFOLD POWER (OPT)
R 202-540-000
S 202-540-000

CARLSON
T 202-540-000 UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
U 1042-8040 WHITE 18 36" 415 BERM DOWN (OPT) INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN MP 04-09-07
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
V 1042-8040 YELLOW 18 36" 413 BERM UP (OPT) 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

W 202-540-000 4. APPLICATION OF ENGINEERING DRAWINGS PER

ASME Y14.24-1999
TITLE JACK AS. - VALVES (LH)
DESIGN MP 04-09-07
5. DO NOT SCALE DRAWING DEUTSCH
X 202-540-000 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER GENERIC

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.34
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-870-000 00+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 210 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8050 JACK 1

800-889-0661
00 INITIAL RELEASE 04-10-07 MP 2 1042-8040 CONTACT PIN SIZE 16 5
5304 01 CHANGED WIRING 10-04-07 RF 3 202-540-000 SEAL- ELECTRICAL 4
5307 02 ADDED WIRE TO PIN "J" FOR MOTION PARTIAL KILL 10-19-07 RF 4 1048-3510 WASHER - INT STAR - #4 2
D D
5 1048-9390 SCREW 2
6 1043-0265 WIRE - STRANDED (18AWG)(BLACK) 36"
7 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 36"

1
8 1043-0273 WIRE - STRANDED (18AWG)(WHITE) 36"

SHT
9 1043-0272 WIRE - STRANDED (18AWG)(RED) 36"

02
10 1043-0270 WIRE - STRANDED (18AWG)(ORANGE) 36"

REV
305-873-000
C

DWG
NO.
B

JACK WIRE LIST

PIN TERMINAL WIRE WIRE WIRE WIRE
FUNCTION
OUT USED COLOR AWG LENGTH #
A 1042-8040 BLACK 18 36" A1 ACCESSORY GROUND
B 1042-8040 WHITE 18 36" A2 ACCESSORY POWER
C 1042-8040 YELLOW 18 36" A3 HEAT GROUND
D 202-540-000
E 202-540-000
F 202-540-000

CARLSON
G 202-540-000 UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
H 1042-8040 BROWN 18 36" A4 HEAT POWER INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN MP 04-10-07
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
J 1042-8040 ORANGE 18 36" SEE NOTE 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE JACK AS.- GENERATOR
NOTE: PIN "J" IS USED ONLY ON PF 400, 410, 161, 171 WITH ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN MP 04-10-07

MOTION PARTIAL HEAT KILL 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.56
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-873-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 211 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8026 JACK - 31 SOCKET 1

800-889-0661
5672 00 INITIAL RELEASE 03-03-09 RF KAC 2 1042-8041 SOCKET 16AWG, DEUTSCH 20
3 202-540-000 SEAL- ELECTRICAL 11
4 1043-0260 WIRE - STRANDED (16AWG) (YELLOW) 720"
D D
5 1042-0353 NUT - SIZE 24 1
6 1042-0354 LOCK WASHER - SIZE 24 1

1
NOTE: ITEM 3 AND 4 ARE NOT SHOWN.

SHT
00
REV
JACK WIRE LIST
PIN TERMINAL WIRE WIRE WIRE WIRE
FUNCTION
OUT USED COLOR AWG LENGTH #
1 1042-8041 YELLOW 16 36" 118 +24 VDC
2 1042-8041 YELLOW 16 36" 119 +24 VDC 5

305-571-000
3 1042-8041 YELLOW 16 36" 200 GROUND
4 1042-8041 YELLOW 16 36" SP1
5 1042-8041 YELLOW 16 36" 718 LH TOWPOINT UP
C 6 1042-8041 YELLOW 16 36" 719 LH TOWPOINT DOWN
7 1042-8041 YELLOW 16 36" 939 LH CONVEYOR MANUAL
8 1042-8041 YELLOW 16 36" 938 LH CONVEYOR OFF
9 1042-8041 YELLOW 16 36" 806 LH EXTENSION IN
1
10 1042-8041 YELLOW 16 36" 807 LH EXTENSION OUT
11 1042-8041 YELLOW 16 36" 929 LH AUGER MANUAL

DWG
12 1042-8041 YELLOW 16 36" 928 LH AUGER OFF

NO.
13 1042-8041 YELLOW 16 36" 935 LH AUGER REVERSE
14 1042-8041 YELLOW 16 36" 304 HORN
15 1042-8041 YELLOW 16 36" 911 LH E-STOP IN
16 1042-8041 YELLOW 16 36" 912 E-STOP CROSSOVER
17 1042-8041 YELLOW 16 36" GEN GEN
18 1042-8041 YELLOW 16 36" SP2 SPARE 6
19 1042-8041 YELLOW 16 36" SP3 SPARE
20 1042-8041 YELLOW 16 36" SP4 SPARE
B
21 202-540-000
22 202-540-000
23 202-540-000 2
24 202-540-000
25 202-540-000
26 202-540-000
27 202-540-000
28 202-540-000
29 202-540-000
30 202-540-000
31 202-540-000

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-03-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-03-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - CROSSOVER
DESIGN RF 03-03-09
5. DO NOT SCALE DRAWING DYNAPAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-03-09

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.35
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-571-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 212 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 1042-8022 CONNECTOR - 3-PIN 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1042-8032 W3P WEDGELOCK 1

800-889-0661
00 INITIAL RELEASE 09/28/07
3 1042-8040 CONTACT PIN SIZE 16 2
4 202-540-000 SEAL- ELECTRICAL 1
D 5 1043-0138 TUBE - SHRINK 1/2" 1 D
6 1043-0110 SLEEVING - BRAIDED (3/8") 1

1
SHT
01+
REV
300-188-000
C

DWG
NO.
B

PLUG WIRE LIST

PIN TERMINAL WIRE WIRE WIRE
OUT USED COLOR AWG LENGTH
A 1042-8040 BLACK 16 56"
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A B 1042-8040 WHITE 16 36" 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994
INCH STANDARD AND INCLUDE APPLIED FINISHES
A
BLANK 202-540-000
DRAWN RF 7/6/2006
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. 3-PIN LADD
DESIGN
5. DO NOT SCALE DRAWING TEMPATURE SENSOR LEAD
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = B 300-188-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 213 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0520 JACK - 14 SOCKET 1

800-889-0661
5672 00 INITIAL RELEASE 03-03-09 RF KAC 2 1042-8041 SOCKET 16AWG, DEUTSCH 7
3 202-540-000 SEAL- ELECTRICAL 7
4 1042-0524 NUT - SIZE 18 1
D D
5 1042-0525 LOCK WASHER - SIZE 18 1
6 1043-0268 WIRE - STRANDED (18AWG)(GREEN) 36"
7 1043-0272 WIRE - STRANDED (18AWG)(RED) 36"

1
8 1043-0267 WIRE - STRANDED (18AWG)(BROWN) 36"

SHT
9 1043-0260 WIRE - STRANDED (16AWG) (YELLOW) 180"

00
REV
NOTE: ITEM 3, 6, 7, 8 AND 9 ARE NOT SHOWN.

305-872-500
C

5
PIN TERMINAL WIRE WIRE WIRE
WIRE # FUNCTION

DWG
OUT USED COLOR AWG LENGTH

NO.
A 1042-8041 RED 16 36" 119 POWER
B 1042-8041 YELLOW 16 36" 928 AUGER OFF
C 1042-8041 YELLOW 16 36" 929 AUGER MANUAL
D 202-540-000 BLACK 16 36" 200 GROUND 4 2
E 202-540-000 YELLOW 16 36" 850 A/C POWER
F 202-540-000
G 1042-8041 YELLOW 16 36" 718 TOWPOINT UP
B H 1042-8041 YELLOW 16 36" 719 TOWPOINT DOWN
J 1042-8041 GREEN 18 36" 806/808 RH EXT. OUT / LH EXT. IN
K 1042-8041 BROWN 18 36" 807/809 RH EXT. IN / LH EXT. OUT
L 202-540-000
M 202-540-000
N 202-540-000 1
P 202-540-000

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-03-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-03-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - REMOTE
DESIGN RF 03-03-09
5. DO NOT SCALE DRAWING 3 FUNCTION
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-03-09

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.29
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-872-500 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 214 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
1 305-501-201 ELECTRICAL BOX - LAYOUT 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 300-126-400 FACE PLATE - RH 1

800-889-0661
5861 00 INITIAL RELEASE 10-02-09 RF KAC 3 1042-0294 DISCONNECT - MALE (16-14AWG) 1
6018 01 CHANGED CONVEYOR AND AUGER WIRING 04-28-10 RF KAC 4 1042-0825 SPLICE - BUTT, YELLOW SHRINK 9
5 1042-0815 SPLICE - BUTT, BLUE SHRINK 10
6062 02 DELETED 1044-0122 AND ADDED 1044-0115 X 2, 1042-9118 6/25/2010 RF KAC
6 1042-0297 CONNECTOR - SPADE 3
D D
7 1042-0270 TERMINAL - SHRINK RING (BLUE) (#6) 26
8 305-872-500 JACK AS. - REMOTE 1
9 1044-7001 SWITCH - TOGGLE 1NT1-6 2

1
10 1044-0116 SWITCH - TOGGLE 1NT1-7E 3
11 1044-0115 SWITCH - TOGGLE 1NT1-7 4

SHT
12 300-400-000 PLATE - DEUTSCH 24 SHELL SIZE LOCK 3
43 25 13 300-399-000 PLATE - DEUTSCH SIZE 18 LOCK 1

02
14 1048-0350 BOLT - STR. BIT PAN HD - 10 - 32 * 4 1/2" 4

REV
26 15 1048-3520 WASHER - EXT STAR - #10 5
16 1048-3100 WASHER - FLAT - #10 SAE 6
24 17 1048-2015 NUT - ACORN - #10-32 (SS) 1
18 1048-1830 BOLT - PAN HD PHILLIPS - 10 - 32 * 3/4" 1
38 36 37 35 19 300-069-000 TUBE, STANDOFF 4
8 20 1043-0349 CABLE STOP - DOUBLE 2
32 33 31 34 21 1043-0090 428-2-VC NICROPRESS SLEEVE 1

305-501-200
22 1043-0348 3/64" SS NYLON CABLE 18"
23 1042-0860 TERMINAL - SHRINK RING 4
24 305-871-000 JACK AS. - VALVES (RH) 1
C
25 305-575-000 JACK AS. - TRACTOR 1
26 305-571-000 JACK AS. - CROSSOVER 1
27 1044-0333 DIODE - 6 AMP 2
28 97944-04 HOLE - PLUG (1/2") 1
29 1044-0157 CONTACT BLOCK - (1) NC 1
30 1044-0158 PUSHBUTTON HEAD 1
16 15 14 31 1048-3145 WASHER - FLAT - 3/8" SAE 4

DWG
32 1048-1131 BOLT- HEX - 3/8-16 * 1 1/4" 2

NO.
33 1048-2053 NUT - HEX - 3/8"-16 NYLOCK 2
34 1042-9064 CONTROLLER-MOBA 2
30 1 35 1048-3085 WASHER - FLAT - #8 SAE 8
36 1048-3515 WASHER - STAR (EXTERNAL) - #8 4
37 1048-2007 NUT- HEX 4
38 1048-1816 BOLT - PAN HEAD PHILLIPS - #8-32 * 5/8" 4
39 1042-9065 REOSTAT 2
28 40 1044-0460 KNOB, BLACK 2
2
41 1044-7020 CAP -RED 8
B
42 1044-0114 SWITCH - TOGGLE 1NT1-5 1
43 1042-9118 CAP, FLANGED 4
39

42
NOTE: ITEMS 3, 4, 5, 6, 7, 20, 21, 22, 23, 27 AND 41 ARE NOT SHOWN.
19
18 16 15 17
29
40
10

39
11
13 12
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
11 INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 10-02-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
11 9 3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER
ASME Y14.3M-1994 CHECKED KAC 10-02-09
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

10 11 10 4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE BOX AS. - CONTROL (RH)

9 ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN RF 10-02-09
DYNAPAC
2 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
ENGINEER KAC 10-02-09
7. CHAMFER OR DEBURR HOLES MAX = .010

DynapacParts.com
8. TOLERANCES:
SIMILAR 305-500-200 MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 21.44
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 305-501-200 02 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661 Page 215 of 251

 8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D D

2 913

1044-0157

860
E-STOP
DynapacParts.com

1044-0114

OVER RIDE

2
932A
942A

J
AUTO

1044-0116
3

850
1

H
HEIGHT
118

SHT
118

MAX
BERM/SLOPE
2
912

G
REVERSE
1044-7001

(OPTINAL)
1044-0209
2

02
850

E F
3
800-889-0661

1
1

2
31

DOWN

REV
3
1
UNLOCK

3
UP

D
30

406
404
934

C
29 861

LOCK

B
28 860

A
27
26
934

MIN
25

1044-0116
931

SLOPE

305-501-200
24

J
932

1044-0115
23

AUGER

H
MANUAL
941

DOWN
22

941

119
932

G
OFF

UP
942

CONVEYOR

118
942

1044-0116
1044-0115

850
21

MANUAL

CROWN
410
1044-7001
935

408

F
C

3
20

HORN
1
3

E
2
928

2
19

850 2

D
929

DOWN
18

OFF

304

C
931
938

UP
418

416
17
939

B
16
913

A
15
911
14
304

DWG
13

NO.
850
12
808
11
809

EXTENSION
1044-0115
10

OUT
400

J
807
9

H
806
8 809

G
720

2
7
721

720

DOWN
721

F
118

TOWPOINT
6
UP

1044-0115

E
719 808
5

402

D
1

718

IN
3
4
200 2

C
200
B 3
B

B
200
2

A
119
1

MAX
118
1042-0352

J
H
3

G
RIGHT CONTROL BOX

F
1

E
D
SPARE
SPARE
SPARE

MIN

C
118
119
200

718
719
939
938
806
807
929
928
935
304

911
912
850

410
406
400
402
404

408
418
416
119
932
931
200
850

721

808
809
720
900

DynapacParts.com

B
1042-0358

W
20

M
10
11
12
13
14
15
16
17
18
19

Q
C
D

1042-0520

U
C
D
A
B

X
P

V
1042-8026

A
B

E
F

T
L

L
J

A
J
1
2
3
4
5
6
7
8
9

A
800-889-0661 CARLSON
PAVING PRODUCTS, INC.
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

TITLE BOX AS. - CONTROL (RH)

DYNAPAC
SIZE DRAWING NUMBER REV SHEET:

B 305-501-200 02 2 OF 2
8 7 6 5 4 3 2 1
Page 216 of 251
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0358 JACK - 23 SOCKET 1

800-889-0661
5203 00 INITIAL RELEASE 04-09-07 MP 2 1042-0353 NUT - SIZE 24 1
REPLACED ITEM 1042-0357 WITH 1042-0358,REPLACED 1042-8040 WITH 1042-8041, 3 1042-0354 LOCK WASHER - SIZE 24 1
5225 01 CHANGED QTY OF 202-540-000 WAS 8, DELETED 1043-0261. UPDATED JACK WIRE LIST 05-17-07 MP
4 1042-8041 SOCKET 16AWG, DEUTSCH 14
D D
5 202-540-000 SEAL- ELECTRICAL 9
6 1043-0268 WIRE - STRANDED (18AWG)(GREEN) 36"
7 1043-0267 WIRE - STRANDED (18AWG)(BROWN) 36"

1
8 1043-0265 WIRE - STRANDED (18AWG)(BLACK) 36"

SHT
9 1043-0266 WIRE - STRANDED (18AWG)(BLUE) 72"

01+
10 1043-0272 WIRE - STRANDED (18AWG)(RED) 36"

REV
11 1043-0269 WIRE - STRANDED (18AWG)(GRAY) 36"
12 1043-0273 WIRE - STRANDED (18AWG)(WHITE) 36"
13 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 36"
14 1043-0271 WIRE - STRANDED (18AWG)(PURPLE) 36"
NOTE: R, T, AND W ARE ONLY PUT IN FOR MACHINES THAT REQUIRE 15 1043-0270 WIRE - STRANDED (18AWG)(ORANGE) 36"

305-871-000
OPEN CENTER, OTHERWISE DO NOT INSTALL THEM 16 1043-0263 WIRE - STRANDED (16AWG) (WHITE) 36"
17 1043-0257 WIRE - STRANDED (16AWG) (BLUE) 36"
C 18 1043-0262 WIRE - STRANDED (16AWG) (PURPLE) 36"

JACK WIRE LIST

5 4 3 2 1
PIN TERMINAL WIRE WIRE WIRE WIRE
FUNCTION

DWG
NO.
OUT USED COLOR AWG LENGTH #
A 1042-8041 RED 18 36" 410 SLOPE DOWN
B 1042-8041 BLACK 18 36" 406 HEIGHT DOWN
C 1042-8041 BROWN 18 36" 402 EXTENSION OUT
D 1042-8041 GREEN 18 36" 400 EXTENSION IN
E 1042-8041 BLUE 18 36" 404 HEIGHT UP
F 202-540-000
B G 1042-8041 BLUE 18 36" 436 VIBE POWER
H 1042-8041 GRAY 18 36" 408 SLOPE UP
J 1042-8041 ORANGE 18 36" 418 CROWN UP
K 1042-8041 PURPLE 18 36" 416 CROWN DOWN
L 1042-8041 BLUE 16 36" 422 AUGER TUNNEL OUT
M 1042-8041 WHITE 16 36" 420 AUGER TUNNEL IN
N 202-540-000
O 202-540-000
P 202-540-000
Q 202-540-000
R 1042-8041 YELLOW 18 36" OPEN CENTER
S 202-540-000
T 1042-8041 BLACK 18 36" OPEN CENTER
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
U 1042-8041 WHITE 18 36" 414 BERM DOWN INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN MP 04-09-07
PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
V 1042-8041 YELLOW 18 36" 412 BERM UP ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE JACK AS. - VALVES (RH)
W 1042-8041 RED 18 36" OPEN CENTER ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN MP 04-09-07
DEUTSCH
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
X 1042-8041 PURPLE 16 36" 440 HORN 7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER GENERIC

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.33
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-871-000 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 217 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0352 JACK - 31 PIN 1

800-889-0661
5672 00 INITIAL RELEASE 03-03-09 RF KAC 2 1042-0353 NUT - SIZE 24 1
3 1042-0354 LOCK WASHER - SIZE 24 1
4 1043-0260 WIRE - STRANDED (16AWG) (YELLOW) 90'
D D
5 1042-8040 CONTACT PIN SIZE 16 30
6 202-540-000 SEAL- ELECTRICAL 1

1
NOTE: ITEMS 4 AND 6 ARE NOT SHOWN.

SHT
00
REV
PIN TERMINAL WIRE WIRE WIRE WIRE
FUNCTION
OUT USED COLOR AWG LENGTH #
1 1042-8040 YELLOW 16 36" 118 +12VDC

305-575-000
2 1042-8040 YELLOW 16 36" 119 +12VDC
3 1042-8040 YELLOW 16 36" 200 GROUND
4 1040-8040 YELLOW 16 36" 200 GROUND
C 5 1042-8040 YELLOW 16 36" 718 LH TOWPOINT UP
6 1042-8040 YELLOW 16 36" 719 LH TOWPOINT DOWN
7 1042-8040 YELLOW 16 36" 721 RH TOWPOINT UP
8 1042-8040 YELLOW 16 36" 720 RH TOWPOINT DOWN 2
9 1042-8040 YELLOW 16 36" 806 LH EXTENSION IN
10 1042-8040 YELLOW 16 36" 807 LH EXTENSION OUT

DWG
11 1042-8040 YELLOW 16 36" 809 RH EXTENSION OUT

NO.
12 1042-8040 YELLOW 16 36" 808 RH EXTENSION IN 5
13 1042-8040 YELLOW 16 36" 850 A/C POWER
14 1042-8040 YELLOW 16 36" 304 HORN
15 1042-8040 YELLOW 16 36" 911 E-STOP IN
16 1042-8040 YELLOW 16 36" 913 E-STOP OUT 1
17 1042-8040 YELLOW 16 36" 939 LH CONVEYOR RUN
18 1042-8040 YELLOW 16 36" 938 LH CONVEYOR STOP
19 1042-8040 YELLOW 16 36" 929 LH AUGER RUN
B
20 1042-8040 YELLOW 16 36" 928 LH AUGER STOP
21 1042-8040 YELLOW 16 36" 935 LH AUGER REVERSE 3
22 1042-8040 YELLOW 16 36" 942 RH CONVEYOR RUN
23 1042-8040 YELLOW 16 36" 941 RH CONVEYOR STOP
24 1042-8040 YELLOW 16 36" 932 RH AUGER RUN
25 1042-8040 YELLOW 16 36" 931 RH AUGER STOP
26 1042-8040 YELLOW 16 36" 934 RH AUGER REVERSE
27 1042-8040 YELLOW 16 36" SPA SPARE
28 1042-8040 YELLOW 16 36" 900 GENERATOR
29 1042-8040 YELLOW 16 36" SPA SPARE
30 1042-8040 YELLOW 16 36" SPA SPARE
31 202-540-000

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-03-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-03-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - TRACTOR
DESIGN RF 03-03-09
5. DO NOT SCALE DRAWING 31 PIN - DYNAPAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-03-09

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.31
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-575-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 218 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8024 PLUG - 23 SOCKET 1

800-889-0661
5203 00 INITIAL RELEASE 04-16-07 MP 2 1042-8041 SOCKET 16AWG, DEUTSCH 15
CHANGED QTY OF 1043-0268,1043-0267,1043-0265,1043-0266,1043-0272,1043-0269,1043- 3 202-540-000 SEAL- ELECTRICAL 8
0273,1043-0274,1043-0257,1043-0263 WAS 122"; CHANGED QTY OF 1043-0261 WAS 50";
5225 01 CHANGED QTY OF 1042-8041 WAS 13 AND 202-540-000 WAS 10 AND 1043-0110 WAS 36"; 05-17-07 MP
4 1042-0821 CONNECTOR 3
D DELETED ITEMS 1043-0256 AND 1043-0258; ADDED ITEM 1042-0805;UPDATED WIRE LIST D
5 1042-0805 CAP, WIRE END 6
5386 02 ADDED PART NUMBER 80504 04-22-08 RF 6 1043-0268 WIRE - STRANDED (18AWG)(GREEN) 186"
7 1043-0267 WIRE - STRANDED (18AWG)(BROWN) 120"

1
8 1043-0265 WIRE - STRANDED (18AWG)(BLACK) 120"

SHT
9 1043-0266 WIRE - STRANDED (18AWG)(BLUE) 120"

02
10 1043-0272 WIRE - STRANDED (18AWG)(RED) 186"

REV
11 1043-0269 WIRE - STRANDED (18AWG)(GRAY) 120"
12 1043-0273 WIRE - STRANDED (18AWG)(WHITE) 120"
13 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 120"
14 1043-0257 WIRE - STRANDED (16AWG) (BLUE) 120"
15 1043-0263 WIRE - STRANDED (16AWG) (WHITE) 120"

305-880-000
16 1043-0261 WIRE - STRANDED (16AWG) (BLACK) 66"
17 1043-0130 SLEEVING - BRAIDED (3/4") 96"
C 18 1043-0110 SLEEVING - BRAIDED (3/8") 60"
19 80504 DIN PLUG - FEMALE 6
NOTE: R IS ONLY PUT IN FOR MACHINES THAT REQUIRE
OPEN CENTER, OTHERWISE DO NOT INSTALL
3 2 1

WIRE LIST

DWG
NO.
PINOUT TERMINAL TERMINAL WIRE
COLOR AWG LENGTH FUNCTION
PLUG 1 USED USED #
A 1042-8041 1042-0136 RED 407 18 120" SLOPE DOWN
B 1042-8041 1042-0136 BLACK 411 18 120" HEIGHT DOWN
C 1042-8041 1042-0136 BROWN 401 18 120" EXTENSION IN
D 1042-8041 1042-0136 GREEN 403 18 120" EXTENSION OUT
E 1042-8041 1042-0136 BLUE 405 18 120" HEIGHT UP
B F 202-540-000
G 202-540-000
H 1042-8041 1042-0136 GRAY 409 18 120" SLOPE UP
J 1042-8041 1042-0805 ORANGE 417 18 120" CROWN UP
K 1042-8041 1042-0805 PURPLE 419 18 120" CROWN DOWN
L 1042-8041 1042-0805 BLUE 421 16 120" AUGER TUNNEL IN (OPT)
M 1042-8041 1042-0805 WHITE 423 16 120" AUGER TUNNEL OUT (OPT)
N 1042-8041 1042-0821 BLACK 425 16 66" MANIFOLD GROUND (OPT)
O 202-540-000
P 1042-8041 1042-0821 RED 427 18 66" MANIFOLD POWER (OPT)
Q 1042-8041 1042-0821 GREEN 429 18 66" MANIFOLD POWER (OPT)
R 1042-8041 1042-8041 YELLOW 16 120" OPEN CENTER
S 202-540-000
T 202-540-000
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES
U 1042-8041 1042-0805 WHITE 415 18 120" BERM DOWN (OPT) 2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN MP 04-16-07
PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
V 1042-8041 1042-0805 YELLOW 413 18 120" BERM UP (OPT) ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER TITLE HARNESS AS. - VALVES (LH)
W 202-540-000 ASME Y14.24-1999
5. DO NOT SCALE DRAWING
DESIGN MP 04-16-07
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
X 202-540-000 7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER DEUTSCH CONNECTORS

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.89
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-880-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 219 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8025 PLUG - 23 PIN 1

800-889-0661
5203 00 INITIAL RELEASE 04-17-07 MP 2 1042-8040 CONTACT PIN SIZE 16 14
REPLACED ITEM 1042-8024 WITH 1042-8025, REPLACED 1042-8041 WITH 1042-8040,
CHANGED QTY OF 202-540-000 WAS 8 CHANGED QTY OF 1042-0136 WAS 10, CHANGED
3 202-540-000 SEAL- ELECTRICAL 9
5225 01 05-17-07 MP
QTY OF 1042-0821 WAS 2, CHANGED QTY OF 1042-0805 WAS 2. DELETED 1043-0110AND 4 1043-0268 WIRE - STRANDED (18AWG)(GREEN) 122"
D 1043-0261, UPDATED WIRE LIST D
5 1043-0267 WIRE - STRANDED (18AWG)(BROWN) 122"
5386 02 ADDED PART NUMBER 80504 04-22-08 RF
6 1043-0265 WIRE - STRANDED (18AWG)(BLACK) 122"
7 1043-0266 WIRE - STRANDED (18AWG)(BLUE) 224"

1
8 1043-0272 WIRE - STRANDED (18AWG)(RED) 122"

SHT
9 1043-0269 WIRE - STRANDED (18AWG)(GRAY) 122"

02
10 1043-0273 WIRE - STRANDED (18AWG)(WHITE) 122"

REV
11 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 122"
12 1043-0271 WIRE - STRANDED (18AWG)(PURPLE) 122"
13 1043-0270 WIRE - STRANDED (18AWG)(ORANGE) 122"
14 1043-0257 WIRE - STRANDED (16AWG) (BLUE) 122"
15 1043-0263 WIRE - STRANDED (16AWG) (WHITE) 122"

305-881-000
16 1043-0262 WIRE - STRANDED (16AWG) (PURPLE) 24"
17 1042-0297 CONNECTOR - SPADE 1
NOTE: R, T AND w ARE USE FOR MACHINES THAT REQUIRE ONLY
18 1042-0821 CONNECTOR 1
C
DO NOT INSTALL IF IT DOES NOT REQUIRE IT.
19 1042-0805 CAP, WIRE END 4
20 1043-0130 SLEEVING - BRAIDED (3/4") 96"
21 80504 DIN PLUG - FEMALE 8

WIRE LIST

DWG
NO.
PINOUT TERMINAL TERMINAL WIRE 3 2 1
COLOR AWG LENGTH FUNCTION
PLUG 1 USED USED #
A 1042-8040 1042-0136 RED 410 18 122" SLOPE DOWN
B 1042-8040 1042-0136 BLACK 406 18 122" HEIGHT DOWN
C 1042-8040 1042-0136 BROWN 402 18 122" EXTENSION OUT
D 1042-8040 1042-0136 GREEN 400 18 122" EXTENSION IN
E 1042-8040 1042-0136 BLUE 404 18 122" HEIGHT UP
B F 202-540-000
G 1042-8040 1042-0821 BLUE 436 18 102" VIBE POWER
H 1042-8040 1042-0136 GRAY 408 18 122" SLOPE UP
J 1042-8040 1042-0136 ORANGE 416 18 122" CROWN UP
K 1042-8040 1042-0136 PURPLE 418 18 122" CROWN DOWN
L 1042-8040 1042-0805 BLUE 422 16 122" AUGER TUNNEL IN
M 1042-8040 1042-0805 WHITE 420 16 122" AUGER TUNNEL OUT
N 202-540-000
O 202-540-000
P 202-540-000
Q 202-540-000
R 1042-8040 1042-8041 YELLOW 18 122" OPEN CENTER
S 202-540-000
T 1042-8040 1042-8041 BLACK 18 122" OPEN CENTER
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
U 1042-8040 1042-0805 WHITE 414 18 122" BERM DOWN INCH STANDARD AND INCLUDE APPLIED FINISHES
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH
DRAWN MP 04-17-07
PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
V 1042-8040 1042-0805 YELLOW 412 18 122" BERM UP ASME Y14.3M-1994 CHECKED

W 1042-8040 1042-8041 RED 18 122" OPEN CENTER

4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE HARNESS AS. - VALVES (RH)
DESIGN MP 04-17-07
5. DO NOT SCALE DRAWING
X 202-540-000 1042-0297 PURPLE 440 16 24" HORN 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER DEUTSCH CONNECTORS

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.91
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-881-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 220 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0348 PLUG - 31 PIN 2

800-889-0661
5672 00 INITIAL RELEASE 03-03-09 RF KAC 2 1042-8040 CONTACT PIN SIZE 16 40
3 202-540-000 SEAL- ELECTRICAL 22
4 1043-0140 BRAIDED SLEEVING - 1 1/4" 1
D D
5 1043-0260 WIRE - STRANDED (16AWG) (YELLOW) 308.3'
6 1048-2006 NUT - ACORN - #8-32 (NYLON) 4

1
SHT
NOTE: ITEM 2, 3, 4, 5 AND 6 ARE NOT SHOWN.

00
120"

REV
WIRE LIST

305-560-000
PINOUT TERMINAL PINOUT TERMINAL WIRE
COLOR AWG LENGTH FUNCTION
PLUG 1 USED PLUG 2 USED #
1 1042-8040 1 1042-8040 YELLOW 118 16 185" +24VDC
C 2 1042-8040 2 1042-8040 YELLOW 119 16 185" +24VDC
3 1042-8040 3 1042-8040 YELLOW 200 16 185" GROUND
4 1042-8040 4 1042-8040 YELLOW SP1 16 185"
5 1042-8040 5 1042-8040 YELLOW 718 16 185" LH TOWPOINT UP
6 1042-8040 6 1042-8040 YELLOW 719 16 185" LH TOWPOINT DOWN
7 1042-8040 7 1042-8040 YELLOW 939 16 185" LH CONVEYOR MANUAL

DWG
8 1042-8040 8 1042-8040 YELLOW 938 16 185" LH CONVEYOR OFF

NO.
9 1042-8040 9 1042-8040 YELLOW 806 16 185" LH EXTENSION IN
10 1042-8040 10 1042-8040 YELLOW 807 16 185" LH EXTENSION OUT
11 1042-8040 11 1042-8040 YELLOW 929 16 185" LH AUGER MANUAL
12 1042-8040 12 1042-8040 YELLOW 928 16 185" LH AUGER OFF
13 1042-8040 13 1042-8040 YELLOW 935 16 185" LH AUGER REVERSE
14 1042-8040 14 1042-8040 YELLOW 304 16 185" HORN
15 1042-8040 15 1042-8040 YELLOW 911 16 185" LH E-STOP IN
16 1042-8040 16 1042-8040 YELLOW 912 16 185" E-STOP CROSSOVER
B
17 1042-8040 17 1042-8040 YELLOW GEN 16 185" GEN
18 1042-8040 18 1042-8040 YELLOW SP2 16 185" SPARE
19 1042-8040 19 1042-8040 YELLOW SP3 16 185" SPARE
20 1042-8040 20 1042-8040 YELLOW SP4 16 185" SPARE
21 202-540-000 21 202-540-000 1
22 202-540-000 22 202-540-000
23 202-540-000 23 202-540-000
24 202-540-000 24 202-540-000
25 202-540-000 25 202-540-000
26 202-540-000 26 202-540-000
27 202-540-000 27 202-540-000
28 202-540-000 28 202-540-000
29 202-540-000 29 202-540-000
30 202-540-000 30 202-540-000
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 31 202-540-000 31 202-540-000 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-03-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-03-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. - CROSSOVER
DESIGN RF 03-03-09
5. DO NOT SCALE DRAWING DYNAPAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-03-09

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 1.74
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-560-000 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 221 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8027 PLUG - 31 SOCKET 1

800-889-0661
5672 00 INITIAL RELEASE 03-03-09 RF KAC 2 202-540-000 SEAL- ELECTRICAL 2
5755 01 DELETED 1042-8027 X 1, 1042-8041 X 21, 202-540-000 X 8 & ADDED 1042-0348, 1042-8040 05-19-09 RF KAC 3 1042-8041 SOCKET 16AWG, DEUTSCH 30
4 1043-0260 WIRE - STRANDED (16AWG) (YELLOW) 2880"
D D
5 1043-0130 SLEEVING - BRAIDED (3/4") 96"
6 1042-0348 PLUG - 31 PIN 1
7 1042-8040 CONTACT PIN SIZE 16 30

1
SHT
01
WIRE LIST

REV
PINOUT TERMINAL PIN OUT WIRE
COLOR AWG LENGTH
PLUG 1 USED PLUG 2 #
1 1042-8041 1042-8040 YELLOW 118 16 96"
2 1042-8041 1042-8040 YELLOW 119 16 96"
3 1042-8041 1042-8040 YELLOW 200 16 96"

305-540-000
4 1042-8041 1042-8040 YELLOW 200 16 96"
5 1042-8041 1042-8040 YELLOW 718 16 96"
6 1042-8041 1042-8040 YELLOW 719 16 96"
C 7 1042-8041 1042-8040 YELLOW 721 16 96"
8 1042-8041 1042-8040 YELLOW 720 16 96" 96"
9 1042-8041 1042-8040 YELLOW 806 16 96"
10 1042-8041 1042-8040 YELLOW 807 16 96"
11 1042-8041 1042-8040 YELLOW 809 16 96"
12 1042-8041 1042-8040 YELLOW 808 16 96"
13 1042-8041 1042-8040 YELLOW 842 16 96"

DWG
NO.
14 1042-8041 1042-8040 YELLOW 304 16 96" 6
15 1042-8041 1042-8040 YELLOW 911 16 96"
16 1042-8041 1042-8040 YELLOW 913 16 96"
17 1042-8041 1042-8040 YELLOW 939 16 96"
18 1042-8041 1042-8040 YELLOW 938 16 96"
19 1042-8041 1042-8040 YELLOW 929 16 96"
20 1042-8041 1042-8040 YELLOW 928 16 96"
21 1042-8041 1042-8040 YELLOW 935 16 96"
B
22 1042-8041 1042-8040 YELLOW 942 16 96"
23 1042-8041 1042-8040 YELLOW 941 16 96"
24 1042-8041 1042-8040 YELLOW 932 16 96"
25 1042-8041 1042-8040 YELLOW 931 16 96"
26 1042-8041 1042-8040 YELLOW 934 16 96"
27 1042-8041 1042-8040 YELLOW SP1 16 96"
28 1042-8041 1042-8040 YELLOW GEN 16 96"
29 1042-8041 1042-8040 YELLOW SP2 16 96"
30 1042-8041 1042-8040 YELLOW SP3 16 96"
31 202-540-000 202-540-000

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-03-09
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-03-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. - TRACTOR (RH)
DESIGN RF 03-03-09
5. DO NOT SCALE DRAWING DYNAPAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-03-09

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-540-000 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 222 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0001 GRIP - CORD (1/2") (.375-.50) 1

800-889-0661
5861 00 INITIAL RELEASE 10-02-09 RF KAC 2 1044-0115 SWITCH - TOGGLE 1NT1-7 3
3 210-304-000 REMOTE BOX - 3 SWITCH 1
4 1042-0270 TERMINAL - SHRINK RING (BLUE) (#6) 11
D D
5 1042-0521 PLUG - 14 PIN 1
6 1042-8040 CONTACT PIN SIZE 16 9
7 1043-0321 CORD - RETRACTILE 1

1
8 300-126-200 DECAL (RH) 1

SHT
NOTE: ITEMS 1, 4 AND 6 ARE NOT SHOWN

00
932

931

REV
A
7
2 OFF B
3 1

305-501-300
AUGER C
C
1044-0115 850
D
721 UP E
OVER RIDE
200 2 1 F

DWG
NO.
720 G
8
3 H 5
TOWPOINT
1044-0115 DOWN J
B

K 2

3
808 809 L
2

M
IN 3 1 OUT
2 N 2

P
119 EXTENSION
1044-0115
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 3/2/2009
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-03-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE REMOTE AS. - (RH)
DESIGN RF 03-03-09
5. DO NOT SCALE DRAWING 3 - SWITCH
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-03-09 DYNAPAC

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-501-300 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 223 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0001 GRIP - CORD (1/2") (.375-.50) 1

800-889-0661
5861 00 INITIAL RELEASE 10-02-09 RF KAC 2 1044-0115 SWITCH - TOGGLE 1NT1-7 3
3 210-304-000 REMOTE BOX - 3 SWITCH 1
4 1042-0270 TERMINAL - SHRINK RING (BLUE) (#6) 11
D D
5 1042-0521 PLUG - 14 PIN 1
6 1042-8040 CONTACT PIN SIZE 16 9
7 1043-0321 CORD - RETRACTILE 1

1
8 300-127-200 DECAL (LH) 1

SHT
NOTE: ITEMS 1, 4 AND 6 ARE NOT SHOWN

00
929

928

REV
A
7
2 OFF B
3 1

305-501-400
AUGER C
C
1044-0115 850
D
718 UP E
OVER RIDE
200 2 1 F

DWG
NO.
719 G
8
3 H 5
TOWPOINT
1044-0115 DOWN J
B

K 2

3
806 807 L
2

M
IN 3 1 OUT
2 N 2
2

P
119 EXTENSION
1044-0115
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 10/2/2009
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 10-02-09
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE REMOTE AS. - (LH)
DESIGN RF 10-02-09
5. DO NOT SCALE DRAWING 3 - SWITCH
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 10-02-09 DYNAPAC

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT.
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-501-400 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661 Page 224 of 251

 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 305-965-100 BOX AS. - GENERATOR DISTRIBUTION 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 305-960-200 JUNCTION BOX- MAIN ELEMENT 1

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC
3 305-900-940 OVEN SWITCH AS. 1
6027 01 ADDED 305-960-300 & 305-960-400 05-10-10 RF KAC
4 300-088-300 CABLE AS. - BOLT-ON (HEAT) 2
6082 02 CHANGED OVEN WIRING 07-19-10 RF KAC
D 5 305-882-000 CABLE AS. - GENERATOR CONTROL 1 D
6337 03 UPDATED SCHEMATIC 08-10-11 TH
6 305-960-300 CABLE AS. - EXTENSION - BOLTON (RH) 1
7 305-960-400 CABLE AS. - EXTENSION - BOLTON (LH) 1

1
7

SHT
03
6

REV
3

305-965-000
C

DWG
NO.
4

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE AC ELECTRICAL GROUP
5. DO NOT SCALE DRAWING
DESIGN RF 03-17-10
24 VDC - SINGLE HEAT
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
THIRD ANGLE PROJECTION 7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10 DYNAPAC

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 47.15
.XX
.XXX =
= 0.03
0.01 FINISH =
25 SEE BOM B 305-965-000 03 1 OF 3
8 7 6 5 4 3 2 1

800-889-0661
 8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

L2
L3
L11
L12
D NEU D
LEFT

FRONT CENTER REAR

DynapacParts.com
OV

2
L1
L2
L3
L10

SHT
L11

2400 WATTS

2400 WATTS

2400 WATTS
L2 L12
N
L1 G
L3

03
G

N
800-889-0661
N

L12 L10

REV
OV

N
L11 FRONT 20A

FRONT 20A
LEFT MAIN

CENTER
20A A B C A B C A B C

A B C A B C A B C
34 kVA GENERATOR
240V AC SINGLE PHASE CENTER FRONT 20A
20A

REAR 20A FRONT 20A

LEFT MAIN
CENTER

305-965-000
REAR 20A 20A

CENTER
FRONT 20A 20A

A G F H T U Q R S K L X W V P O N M B J E D C
A G F H T U Q R S K L X W V P O N M B J E D C
FRONT REAR 20A
20A
RIGHT MAIN

N N 1 10

C CENTER
20A
REAR 20A

G
CENTER 2 11 FRONT 20A
20A

OV
REAR 20A FRONT 20A

RIGHT MAIN
3 12

CENTER
REAR 20A 20A

CENTER
LEFT 20A 20A
EXTENSIONS

LEFT 20A REAR 20A

DWG
NO.
LEFT 20A REAR 20A

LH BOLT RH BOLT
LEFT 20A RH EXT RH EXT LEFT 20A
REAR CENTER FRONT

EXT
6
2

6
2

6
2

6
2

6
2
RIGHT 20A LEFT 20A
8
4

8
4

8
4
8
4

8
4
BOLT ON

R5

R4

R3

R2

R1
0

0
1

0
RIGHT
0

0
1

1
20A
LEFT 20A

BOLT

1
3
RIGHT 20A
LEFT 20A

RIGHT 20A
RIGHT 20A

12

11

10
EXT
RIGHT 20A
OVEN

OVEN 10A RIGHT 20A

BOLT
B RIGHT 20A
B
LH BOLT RH BOLT
REAR CENTER FRONT
RH EXT RH EXT

A B C D E F G H

2
6

2
A B C D E F G H

8
4
8
4

8
4
8
4

8
4
OVEN
A B C A B C A B C
OVEN 10A
A B C A B C B

R5

R5

R5
0
0

0
C

1
1

1
R5

R5
A

0
1

2400 WATTS

2400 WATTS

2400 WATTS
DynapacParts.com
FRONT CENTER REAR

RIGHT

A
800-889-0661 CARLSON
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
an Astec company
A

TITLE AC ELECTRICAL GROUP

24 VDC - SINGLE HEAT
DYNAPAC
SIZE DRAWING NUMBER REV SHEET:

B 305-965-000 03 2 OF 3
8 7 6 5 4 3 2 1
 8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED LEFT
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED. EXTENSION BOLT ON

L1
L10

1436 DUAL ENDGATES

2095 WATTS BERM
NEU

890 WATTS
1862 WATTS
D D

DynapacParts.com

3
SHT
FRONT 20A

03
800-889-0661
FRONT 20A

REV
LEFT MAIN

CENTER 20A

H
H
G
G
CENTER 20A

F
F
REAR 20A

A
A
B
B

305-965-000
REAR 20A

E
E
C
C
FRONT 20A

D
D
FRONT 20A
C
RIGHT MAIN

CENTER 20A

CENTER 20A
2
3

N
REAR 20A

OV
10
12

N
11

REAR 20A

DWG
NO.
LEFT 20A

D
D
EXT

C
C
LEFT 20A

E
E
LEFT 20A

B
B
BOLT

A
A
LEFT 20A

F
F
G
G
RIGHT 20A
EXT

H
H
B RIGHT 20A
B

RIGHT 20A

4
4
BOLT

3
3
RIGHT LH BOLT

OVEN
20A

2
2
RH BOLT
RH EXT REAR CENTER FRONT
LH EXT

1
1
6

2
6

2
8

OFF
OVEN

ON
OVEN 10A
0

0
1

0
1

1
R5

R5

R5

R5

R5

1436 DUAL ENDGATES

2468 WATTS BERM

890 WATTS
2194 WATTS
DynapacParts.com EXTENSION

RIGHT
BOLT ON

A
800-889-0661 CARLSON an Astec company
18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
A

TITLE AC ELECTRICAL GROUP

24 VDC - SINGLE HEAT
DYNAPAC
SIZE DRAWING NUMBER REV SHEET:

B 305-965-000 03 3 OF 3
8 7 6 5 4 3 2 1
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 305-965-101 ELECTRICAL BOX - LAYOUT 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 300-255-800 LABEL - CIRCUIT BREAKER 1

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC
3 1042-9102 CIRCUIT BREAKER - 10 AMP 1
6082 01 ADDED 1042-9120 AND DELETED 1042-0383, 1042-0184 07-19-10 RF KAC
4 1042-9101 CIRCUIT BREAKER - 20 AMP 20
ITEM #8 201-452-000 WAS REPLACED WITH 1042-0219, ITEM #34 201-453-000 WAS
D
6289 02 REPLACED WITH 1042-0218 06-03-2011 RJM KAC 5 1044-0240 RELAY - 24V DPST 5 D
6337 03 ADDED COMPONENTS FOR GENERATOR CABLE, ADDED SCHEMATIC NOTE 08-10-11 TH 6 1020-3010 6 POST TERMINATION BLOCK M8 1
7 1020-3009 6 POST TERMINATION BLOCK M6 1

1
8 1042-0219 CONNECTOR - 1" (STRAIGHT) 1

SHT
9 305-960-150 JACK AS. - MAIN ELEMENT 1
10 305-960-170 JACK AS. - EXTENSION / BOLT ON ELEMENT 2

03
34 19 36

REV
17 11 1048-3085 WASHER - FLAT - #8 SAE 20
6 12 1048-3515 WASHER - STAR (EXTERNAL) - #8 10
20 13 1048-2007 NUT- HEX 10
10 14 1048-2006 NUT - ACORN - #8-32 (NYLON) 10
7 15 1048-1816 BOLT - PAN HEAD PHILLIPS - #8-32 * 5/8" 10

305-965-100
16 1048-1048 BOLT - HEX - 5/16-18 * 3/4" 2
15 11 12 13 14
17 1048-2220 NUT - HEX - 5/16"-18 TOPLOCK 2
C 8 5 18 1048-3179 WASHER - BRASS (3/4" OD - 5/16"ID) 2
19 1048-3115 WASHER - FLAT - 1/4" SAE 12
20 1048-2022 NUT - HEX - 1/4"-20 6
21 1048-0950 BOLT - HEX - 1/4-20 *1" 2
35
22 1043-0203 WIRE - STRANDED (8AWG) (BLACK) 48'
23 1043-0204 WIRE - STRANDED (8AWG) (RED) 48'

DWG
NO.
24 1043-0205 WIRE - STRANDED (8AWG) (WHITE) 48'
LEAVE 18" OF WIRE 25 1042-0821 CONNECTOR 12
INSIDE BOX 26 1042-0298 12-10 X 1/4" PUSH ON 12
27 1042-0297 CONNECTOR - SPADE 54
28 1042-0280 TERMINAL - RING (8AWG) (5/16") 6
29 1042-0277 RING TERMINAL 12-10 X 5/16" 17
B 30 1042-0281 TERMINAL, RING 16-14 5/16" 18
31 1048-3325 WASHER - LOCK - 1/4" 4
32 19
3 32 1048-0915 BOLT - HEX 4
33 1042-0218 CONDUIT - LIQUIDTIGHT X-FLEX 20'
GENERATOR CABLE WIRE LIST 31 34 305-973-000 JACK AS. - GENERATOR CONTROL 1
WIRE # COLOR LENGTH AWG 35 305-088-300 JACK AS. - 4 PIN 1
1 RED 24' 8 36 1042-9120 BRASS BAR 1
10 RED 24' 8 4 1 9 20
37 1043-0242 WIRE - STRANDED (10AWG)(WHITE) 24'
2 WHITE 24' 8
11 WHITE 24' 8 38 1043-02436 WIRE - STRANDED (10AWG) (ORANGE) 24'
3 BLACK 24' 8 39 1043-02435 WIRE - STRANDED (10AWG) (GREEN) 24'
16
12 BLACK 24' 8
OV ORANGE 24' 10 21 19
2
CARLSON
N WHITE 24' 10 UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
G GREEN 24' 10 INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE BOX AS. - GENERATOR DISTRIBUTION
5. DO NOT SCALE DRAWING
DESIGN RF 03-17-10
24 VDC
NOTES: 1. ITEMS 18, 22 - 30, 33 AND 37 - 39 ARE NOT SHOWN. 6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10 DYNAPAC
2. SEE 305-965-000 FOR SCHEMATIC.
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 31.33
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-965-100 03 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-0358 JACK - 23 SOCKET 1

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC 2 1042-8041 SOCKET 16AWG, DEUTSCH 18
3 202-540-000 SEAL- ELECTRICAL 5
4 1042-0353 NUT - SIZE 24 1
D D
5 1042-0354 LOCK WASHER - SIZE 24 1
6 1043-0263 WIRE - STRANDED (16AWG) (WHITE) 108"
7 1043-0238 WIRE - 14 AWG YELLOW/GREEN STRIPE 108"

1
8 1043-0261 WIRE - STRANDED (16AWG) (BLACK) 108"

SHT
9 300-400-000 PLATE - DEUTSCH 24 SHELL SIZE LOCK 1

00
NOTE: Item 6, 7 & 8 not shown.

REV
305-960-150
JACK WIRE LIST
PIN TERMINAL WIRE
WIRE COLOR WIRE LENGTH TERMINAL # FUNCTION REMARKS
OUT USED AWG
C A 1042-8041 BLACK 14 18" L3 RIGHT FWD THROUGH RELAY
B 1042-8041 WHITE 14 18" L11 LEFT CEN CONSTANT
C 1042-8041 BLACK 14 18" L2 LEFT FWD THROUGH RELAY
D 1042-8041 WHITE 14 18" L11 LEFT FWD CONSTANT 3
E 1042-8041 YELLOW/GREEN 14 18" N LEFT FWD NEUTRAL
F 1042-8041 YELLOW/GREEN 14 18" N RIGHT FWD NEUTRAL
G 1042-8041 WHITE 14 18" L12 RIGHT FWD CONSTANT
H 1042-8041 BLACK 14 18" L3 RIGHT CEN THROUGH RELAY

DWG
NO.
J 1042-8041 BLACK 14 18" L2 LEFT CEN THROUGH RELAY
K 202-540-000
L 202-540-000 1
M 1042-8041 YELLOW/GREEN 14 18" N LEFT CEN NEUTRAL
N 1042-8041 BLACK 14 18" L2 LEFT REAR THROUGH RELAY
2
O 1042-8041 WHITE 14 18" L11 LEFT REAR CONSTANT
P 1042-8041 YELLOW/GREEN 14 18" N LEFT REAR NEUTRAL
Q 1042-8041 BLACK 14 18" L3 RIGHT REAR THROUGH RELAY
R 1042-8041 WHITE 14 18" L12 RIGHT REAR CONSTANT 5
S 1042-8041 YELLOW/GREEN 14 18" N RIGHT REAR NEUTRAL
B T 1042-8041 WHITE 14 18" L12 RIGHT CEN CONSTANT
U 1042-8041 YELLOW/GREEN 14 18" N RIGHT CEN NEUTRAL
V 202-540-000
W 202-540-000
X 202-540-000
4

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - MAIN ELEMENT
DESIGN RF 03-17-10
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.35
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-960-150 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8066 JACK - 8 SOCKET 1

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC 2 1042-8046 SOCKET - SIZE 12 6
6027 01 ADDED 1042-8046 X 1, 1043-02465 & DELETED 202-540-000 X 1, 1043-0246 05-10-10 RF KAC 3 202-540-000 SEAL- ELECTRICAL 2
4 1042-0524 NUT - SIZE 18 1
D D
5 1042-0525 LOCK WASHER - SIZE 18 1
6 300-399-000 PLATE - DEUTSCH SIZE 18 LOCK 1
7 1043-02465 WIRE - STRANDED (12AWG)(GREEN) 24"

1
8 1043-02455 WIRE - STRANDED (12AWG)(WHITE) 48"

SHT
9 1043-0244 WIRE - STRANDED(12AWG)(BLACK) 48"

01
10 1043-0236 WIRE - 12 AWG YELLOW/GREEN STRIPE 24"

REV
ITEM 7, 8, 9 AND 10 NOT SHOWN

JACK WIRE LIST

305-960-170
PIN TERMINAL WIRE WIRE
WIRE COLOR TERMINAL # FUNCTION REMARKS 3 5 4 2 1
OUT USED AWG LENGTH
C
A 1042-8046 BLACK 12 24" L1 EXTENTION THROUGH RELAY
B 1042-8046 WHITE 12 24" L10 EXTENTION CONSTANT
C 1042-8046 BLACK 12 24" L1 BOLT ON THROUGH RELAY
D 1042-8046 WHITE 12 24" L10 BOLT ON CONSTANT
E 1042-8046 YELLOW/GREEN 12 24" N NEUTRAL

DWG
NO.
F 1042-8046 GREEN 12 24" G GROUND
G 202-540-000
6
H 202-540-000

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - EXTENSION / BOLT ON ELEMENT
DESIGN RF 03-17-10
5. DO NOT SCALE DRAWING EXTENSION
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.36
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 305-960-170 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8050 JACK 1

800-889-0661
5203 00 INITIAL RELEASE 04-23-07 MP 2 1042-8040 CONTACT PIN SIZE 16 4
5304 01 CHANGED WIRING 10-04-07 RF 3 202-540-000 SEAL- ELECTRICAL 5
4 1048-9390 SCREW 2
D D
5 1048-3510 WASHER - INT STAR - #4 2
6 1043-0265 WIRE - STRANDED (18AWG)(BLACK) 36"
7 1043-0273 WIRE - STRANDED (18AWG)(WHITE) 60"

1
8 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 60"

SHT
9 1043-0272 WIRE - STRANDED (18AWG)(RED) 36"

01+
REV
1 2 3 4 5

305-973-000
C JACK WIRE LIST
PIN TERMINAL WIRE WIRE WIRE WIRE
FUNCTION
OUT USED COLOR AWG LENGTH #
120 VAC ACCESSORY GROUND ( 240VAC, DYNAPAC
A 1042-8040 BLACK 18 36" A1
CAPPED OFF)
120 VAC ACCESSORY POWER(240, DYNAPAC CAPPED
B 1042-8040 WHITE 18 36" A2
OFF)

DWG
NO.
C 1042-8040 YELLOW 18 60" A3 120/240 VAC HEAT GROUND
D 202-540-000
E 202-540-000
F 202-540-000
G 202-540-000
H 1042-8040 BROWN 18 60" A4 120/240 VAC HEAT POWER
J 202-540-000 BROWN 18 60" B4 ONLY FOR PARTIAL HEAT (CENTER & REAR)

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN MP 04-23-07
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - GENERATOR CONTROL
DESIGN MP 04-23-07
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER DEUTSCH CONNECTORS

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.56
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-973-000 01+ 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 1043-0244 WIRE - STRANDED(12AWG)(BLACK) 36"
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1042-9121 JACK - 4 PIN WITH FLANGE 1

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC
3 1043-02455 WIRE - STRANDED (12AWG)(WHITE) 36"
6082 01 ADDED 1042-9121, 1042-8042, 1042-9108, 1043-0244, 1043-02455, 1043-02465 AND 07-19-10 RF KAC
DELETED 1043-0233, 1042-9109, 1042-9110, 1042-8046, 1043-0138 4 1042-8042 PIN - #12 3
D 5 202-540-000 SEAL- ELECTRICAL 1 D
6 1043-02465 WIRE - STRANDED (12AWG)(GREEN) 36"
7 1042-9108 WEDGELOCK 1

1
8 1048-3510 WASHER - INT STAR - #4 2

SHT
9 1048-9390 SCREW 2

01
REV
305-088-300
C
7

36"

DWG
NO.
4
B

9
JACK WIRE LIST
PIN TERMINAL WIRE WIRE
WIRE COLOR 8
OUT USED AWG LENGTH
1 1042-8046 BLACK 12 24"
2 1042-8046 WHITE 12 24" 2
3 202-540-000 24"
4 1042-8046 GREEN 12 24"

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JACK AS. - 4 PIN
DESIGN RF 03-17-10
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.23
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-088-300 01 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 305-960-201 ELECTRICAL BOX - LAYOUT 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1042-8040 CONTACT PIN SIZE 16 36

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC
3 1042-0196 CONNECTOR - 3/4" STRAIGHT 1
6167 01 ADDED 1042-0217, 1042-0196, 1042-0188 AND DELETED 1042-0199, 1042-0186, 1043-0130 11-17-10 RF KAC
4 1043-0253 WIRE - STRANDED (14AWG) (WHITE) 504"
6347 02 REPLACED 1042-8052 WITH 1042-8048 08-24-11 TH KAC
D 5 1043-0249 WIRE - STRANDED (14AWG)(GREEN) 504" D
JACK WIRE LIST 6 1043-0247 WIRE - STRANDED (14AWG) (BLACK) 504"
7 1042-8025 PLUG - 23 PIN 1

1
PIN TERMINAL WIRE WIRE WIRE 8 202-540-000 SEAL- ELECTRICAL 5

SHT
FUNCTION 9 1042-0217 CONDUIT - 3/4 " LIQUIDTIGHT FLEXIBLE 84"
OUT USED COLOR AWG LENGTH
10 1048-3115 WASHER - FLAT - 1/4" SAE 8

02
REV
A 1042-8040 BLACK 14 84" RIGHT FWD 11 1048-3325 WASHER - LOCK - 1/4" 4
B 1042-8040 WHITE 14 84" LEFT CEN 12 1048-0915 BOLT - HEX 4
C 1042-8040 BLACK 14 84" LEFT FWD 13 1048-2022 NUT - HEX - 1/4"-20 4
D 1042-8040 WHITE 14 84" LEFT FWD
14 1042-0188 3/4" PLASTIC BUSHING 1
E 1042-8040 GREEN 14 84" LEFT FWD
F 1042-8040 GREEN 14 84" RIGHT FWD
15 1042-0383 CONNECTOR - CORD RANGE .250 - .375 6

305-960-200
G 1042-8040 WHITE 14 84" RIGHT FWD 16 1042-0184 NUT - LOCK 1/2" (PIPE) 6
H 1042-8040 BLACK 14 84" RIGHT CEN 17 1042-0187 1/2" PLASTIC BUSHING 6
C J 1042-8040 BLACK 14 84" LEFT CEN 18 1043-0490 SO CORD 16-3 72"
K 202-540-000
19 1042-8048 RECEPTACLE - INLINE (3 PIN) 6
L 202-540-000
M 1042-8040 GREEN 14 84" LEFT CEN 20 1043-0133 SHRINK TUBE - BLACK 18"
N 1042-8040 BLACK 14 84" LEFT REAR 21 1042-0815 SPLICE - BUTT, BLUE SHRINK 18
O 1042-8040 WHITE 14 84" LEFT REAR
P 1042-8040 GREEN 14 84" LEFT REAR

DWG
NO.
Q 1042-8040 BLACK 14 84" RIGHT REAR 84"
6"
R 1042-8040 WHITE 14 84" RIGHT REAR
S 1042-8040 GREEN 14 84" RIGHT REAR
T 1042-8040 WHITE 14 84" RIGHT CEN
U 1042-8040 GREEN 14 84" RIGHT CEN
V 202-540-000
W 202-540-000
X 202-540-000
B

LEFT FRONT RIGHT FRONT

12" 3" 3X
LEFT CENTER RIGHT CENTER
18 20 2 19 17 16 15 1 13 11 10 12 14 3 9 6 5 4 8 2 7
LEFT REAR RIGHT REAR 5 X 18 X

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE JUNCTION BOX- MAIN ELEMENT
5. DO NOT SCALE DRAWING
DESIGN RF 03-17-10
EZIII, EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR SIZE DRAWING NUMBER REV SHEET:
NOTE: ITEM 21 NOT SHOWN .X = 0.10 ANGULAR = 0 30' MATERIAL:
TO
WT. 8.26
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-960-200 02 1 OF 2
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC.
(THE "COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION OF THE COMPANY AND MUST BE RETURNED
TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR
ANY OTHER PARTY WITHOUT THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING
PRODUCTS, INC. ALL RIGHTS RESERVED.

D 800-889-0661 D

2
SHT
02
REV
A G F H T U R Q S K L X W V P O N M J B E D C

305-960-200
C
A
A

A
A
FORWARD

FORWARD
B
B

B
B
C
C

C
C

DWG
2400 WATTS

NO.
2400 WATTS
RIGHT MAIN

A
A

A
A

LEFT MAIN
CENTER

CENTER
B
B

B
B
C
C

C
C
2400 WATTS 2400 WATTS
A
A

A
A
REAR

REAR
B C
B C

B B

B
B
C
C
2400 WATTS 2400 WATTS

A
CARLSON an Astec company
A

18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA

TITLE JUNCTION BOX- MAIN ELEMENT

EZIII, EZIV

DynapacParts.com
SIZE DRAWING NUMBER REV SHEET:

B 305-960-200 02 2 OF 2
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
ITEM NO. PART NUMBER DESCRIPTION QTY.
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED
1 1042-0166 BOX - TWO GANG (WATERTIGHT) 1
ECN REV. DESCRIPTION DATE DRAWN ENG
2 1042-0178 PLUG - 1/2" THD 3

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC
3 1042-0151 CONNECTOR - WATERTIGHT (SCH1027) 2
4 300-239-000 OVEN SWITCH AS. 1
D 5 1043-0233 SO CORD 12/3 17' D
6 1042-9107 RECPTACLE - 4 PIN 1
7 1042-9108 WEDGELOCK 1

1
OVEN 8 1042-8042 PIN - #12 3

SHT
ASSEMBLY 9 202-540-000 SEAL- ELECTRICAL 1
300-013-000 10 1042-0298 12-10 X 1/4" PUSH ON 2

00
REV
11 1042-0860 TERMINAL - SHRINK RING 1
OVEN ELEMENT 12 1043-0138 TUBE - SHRINK 1/2" 4"
2350 WATTS

(PIN - 1) N

305-900-940
(PIN - 2) L1 2
C 4
(PIN - 4) G 1

ON

DWG
NO.
3

OFF
JACK WIRE LIST
PIN TERMINAL WIRE WIRE 5
WIRE COLOR
OUT USED AWG FUNCTION
B
1 1042-8042 BLACK 12 L1
2 1042-8042 WHITE 12 NEU 10
12
3 202-540-000
4 1042-8042 GREEN 12 GRD
4' 12' 11

6
OVEN WIRE LIST
TERMINAL WIRE WIRE
WIRE COLOR
USED AWG FUNCTION 9
1042-0298 BLACK 12 L1
1042-0298 WHITE 12 NEU 8
1042-0860 GREEN 12 GRD
7
STRIP BACK 3"
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE OVEN SWITCH AS.
DESIGN RF 03-17-10
5. DO NOT SCALE DRAWING 120 VAC
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10
THIRD ANGLE PROJECTION

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 5.01
.XX
.XXX =
= 0.03
0.01 FINISH = 25 SEE BOM B 305-900-940 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
DynapacParts.com
800-889-0661

DynapacParts.com
800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8100 MS3102A20-19S JACK 1

800-889-0661
5979 00 INITIAL RELEASE 03-17-10 RF KAC 2 1042-0860 TERMINAL - SHRINK RING 3
3 1043-0233 SO CORD 12/3 36"
4 1042-0328 CAP - DUST 1
D D
5 1048-2000 NUT - HEX - #4-40 4
6 1048-2002 BOLT - PAN HD PHILLIPS - 4 - 40 * 3/4" 4
7 1048-3070 WASHER - FLAT - #4 SAE 8

1
8 1048-3510 WASHER - INT STAR - #4 4

SHT
9 1043-0133 SHRINK TUBE - BLACK 2"

00
REV
3

300-088-300
C

WIRE COLORS

DWG
NO.
1
5
1 9
3
7
6
4

BLACK A
B
WHITE B
8 7 GREEN C

36"

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 03-17-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 03-17-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. - BOLT-ON (HEAT)
DESIGN RF 03-17-10
5. DO NOT SCALE DRAWING EZIII & EZIV
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 03-17-10

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.84
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 300-088-300 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8051 PLUG 2

800-889-0661
5203 00 INITIAL RELEASE 04-17-07 MP 2 1042-8053 BACKSHELL 2
5615 01 REWIRED CABLE 10-10-07 RF KAC 3 1042-8055 COMPRESSION NUT 2
5979 02 CHANGED WIRING 03-17-10 RF KAC 4 1042-8041 SOCKET 16AWG, DEUTSCH 18
D D
5 1043-0274 WIRE - STRANDED (18AWG) (YELLOW) 720"
6 1043-0110 SLEEVING - BRAIDED (3/8") 80"

1
SHT
02
REV
305-882-000
C

80"

DWG
NO.
WIRE LIST
SINGLE HEAT / ZONAL HEAT
PINOUT TERMINAL PINOUT TERMINAL
COLOR WIRE # ** AWG LENGTH SINGLE ZONAL
PLUG 1 USED PLUG 2 USED
B A 1042-8041 A 1042-8041 YELLOW 451 / A1 18 80" ACC. GROUND GROUND
B 1042-8041 B 1042-8041 YELLOW 452 / A2 18 80" ACC. POWER LEFT EXTENSION / BOLT ON
C 1042-8041 C 1042-8041 YELLOW 453 / A5 18 80" HEAT GROUND LEFT BULLNOSE
D 1042-8041 D 1042-8041 YELLOW SP1 / A7 18 80" SPARE 1 LEFT AFT/CEN
E 1042-8041 E 1042-8041 YELLOW SP2 / A3 18 80" SPARE 2 RIGHT EXTENSION / BOLT ON
F 1042-8041 F 1042-8041 YELLOW SP3 / A8 18 80" SPARE 3 RIGHT BULLNOSE
G 1042-8041 G 1042-8041 YELLOW SP4 18 80" SPARE 4 {CATEPILLAR ( BOLT ON)}
H 1042-8041 H 1042-8041 YELLOW 454 / A10 18 80" HEAT POWER RIGHT AFT/CEN
J 1042-8041 J 1042-8041 YELLOW SP5 / A4 18 80" SPARE 5 ACCESSORY

CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN MP 04-17-07
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. - GENERATOR CONTROL
DESIGN MP 04-17-07
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.17
.XX
.XXX =
= 0.03
0.01 FINISH = B 305-882-000 02 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8065 PLUG - 8 PIN 1

800-889-0661
6027 00 INITIAL RELEASE 05-10-10 RF KAC 2 1042-8042 PIN - #12 6
3 202-540-000 SEAL- ELECTRICAL 2
4 1042-0860 TERMINAL - SHRINK RING 6
D D
5 1043-0404 CORD - SO (12AWG)(7 CONDUCTOR) 260"

1
NOTE: ITEMS 2, 3 AND 4 ARE NOT SHOWN.

SHT
00
REV
5 1

305-960-300
C

260"

DWG
NO.
B

CABLE WIRE LIST

PIN TERMINAL WIRE WIRE WIRE
WIRE COLOR FUNCTION
OUT USED AWG LENGTH #
A 1042-8042 BLACK 12 260" L1 EXTENTION (THROUGH RELAY)
B 1042-8042 WHITE 12 260" L10 EXTENTION (CONSTANT)
C 1042-8042 RED 12 260" L1 BOLT ON (THROUGH RELAY)
D 1042-8042 BLUE 12 260" L10 BOLT ON (CONSTANT)
E 1042-8042 BLACK/WHITE 12 260" NEU NEUTRAL
F 1042-8042 GREEN 12 206" GND GROUND
G 202-540-000
H 202-540-000
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 05-10-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 05-10-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. - EXTENSION - BOLTON (RH)
DESIGN RF 04-10-10
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 05-10-10

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.89
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 305-960-300 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 DynapacParts.com
8 7 6 5 4 3 2 1
THIS DRAWING AND ALL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF CARLSON PAVING PRODUCTS, INC. ("THE COMPANY"). THIS DRAWING INCLUDES CONFIDENTIAL INFORMATION PARTS LIST
OF THE COMPANY AND MUST BE RETURNED TO THE COMPANY UPON REQUEST. THIS DRAWING IS PROVIDED FOR A LIMITED PURPOSE, AND MAY NOT BE USED FOR ANY OTHER PARTY WITHOUT
THE PRIOR WRITTEN CONSENT OF THE COMPANY. COPYRIGHT 2007 CARLSON PAVING PRODUCTS, INC. ALL RIGHTS RESERVED ITEM NO. PART NUMBER DESCRIPTION QTY
ECN REV. DESCRIPTION DATE DRAWN ENG 1 1042-8065 PLUG - 8 PIN 1

800-889-0661
6027 00 INITIAL RELEASE 05-10-10 RF KAC 2 1042-8042 PIN - #12 6
3 202-540-000 SEAL- ELECTRICAL 2
4 1042-0860 TERMINAL - SHRINK RING 6
D D
5 1043-0404 CORD - SO (12AWG)(7 CONDUCTOR) 216"

1
NOTE: ITEMS 2, 3 AND 4 ARE NOT SHOWN.

SHT
00
REV
5 1

305-960-400
C

216"

DWG
NO.
B

CABLE WIRE LIST

PIN TERMINAL WIRE WIRE WIRE
WIRE COLOR FUNCTION
OUT USED AWG LENGTH #
A 1042-8042 BLACK 12 216" L1 EXTENTION (THROUGH RELAY)
B 1042-8042 WHITE 12 216" L10 EXTENTION (CONSTANT)
C 1042-8042 RED 12 216" L1 BOLT ON (THROUGH RELAY)
D 1042-8042 BLUE 12 216" L10 BOLT ON (CONSTANT)
E 1042-8042 BLACK/WHITE 12 216" NEU NEUTRAL
F 1042-8042 GREEN 12 216" GND GROUND
G 202-540-000
H 202-540-000
CARLSON
UNLESS OTHERWISE SPECIFIED APPROVALS DATE
A 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M-1994 A
INCH STANDARD AND INCLUDE APPLIED FINISHES DRAWN RF 05-10-10
2. DIMENSIONAL LIMITS APPLY BEFORE PLATING/FINISH PAVING PRODUCTS, INC.
3. MULTIVIEW AND SECTIONAL VIEW DRAWINGS PER 18425 50th AVENUE EAST - TACOMA, WASHINGTON 98446 USA
ASME Y14.3M-1994 CHECKED KAC 05-10-10
4. APPLICATION OF ENGINEERING DRAWINGS PER
ASME Y14.24-1999
TITLE CABLE AS. - EXTENSION - BOLTON (LH)
DESIGN RF 04-10-10
5. DO NOT SCALE DRAWING
6. REMOVE BURRS AND BREAK CORNERS MAX = .030
7. CHAMFER OR DEBURR HOLES MAX = .010 ENGINEER KAC 05-10-10

DynapacParts.com
8. TOLERANCES:
SIMILAR MATERIAL: SIZE DRAWING NUMBER REV SHEET:
TO .X = 0.10 ANGULAR = 0 30'
WT. 0.89
.XX
.XXX =
= 0.03
0.01 FINISH = SEE BOM B 305-960-400 00 1 OF 1
8 7 6 5 4 3 2 1

800-889-0661
 Screed Accessories
EZIII & EZIV

Carlson Paving Products, the premier

DynapacParts.com manufacturer of innovative paving
solutions for over 25 years.

Heated End Gate

800-889-0661
• Improves longitudinal joint quality • Keeps crew members from working
by reducing thermal segregation in unsafe area adjacent to traffic
• Reduces shadowing, tearing, and • 500 degree end gate runner
scabbing of joint interface preheats adjacent mat and forces
• Eliminates operator maintenance more material into joint interface
and wash down, causing premature increasing joint lifecycle
failure

Power Tunnel Kit

• Helps maintain uniform head of • Reduces material handling
material at any width component wear therefore
• Reduces load forces against screed increasing lifecycle
limiting depth changes due to head • Manual extend and auto retract to
of material inconsistencies limit impact areas
• Protects tracks and tires from
overheating causing delaminating
of rubber compounds

Vibratory Notched Beveled Edger

• Available in 12” and 18” widths • 0 to 3000 vibrations per minute
• Use with vibratory sled for adjustment

DynapacParts.com
improved density or statically • Plumed with quick disconnects for
without vibratory sled fast installation
• Will work on left or right side • Vibratory sled doubles as berm

800-889-0661
of screed limiting the need for compactor
multiple units • Beveled edger has heat and angle
• Notch is a variable adjustment 2” of attack / vibratory sled has heat
down from mat surface and vibration
• Spring loaded outside edge
as to not interfere with ride
characteristics
Great paving demands great craftsmanship

Safety Edge End Gate

DynapacParts.com
• Superior bevel using heat and • Spring loaded as to not interfere
extruding material for higher with ride quality characteristics or
density deviations in milled surfaces

800-889-0661
• Applied bevel will not deform under • Third end gate jack to roll in and out
compaction process of bevel faster and safer
• Bevel rotates from 90 degrees for • Hinged lower unit is a replaceable
matching joints to 30 degrees for wear component
applying the safety bevel quick and
easy

Bolt On Segments
• Available in 12”, 18” and 24” • When using more than two
segments segments or one segment with
• Available with heat or without heat heated end gates a “Y” cable will
be needed

Wide Width Support Kit

• Used when adding 4’ or more bolt • Welding of permanent brackets to
on extensions to any easy screed outside of main necessary
• Easy install to Carlson EZIII or EZIV • Don’t go wide without the wide
screeds width support kit

For more information contact:

DynapacParts.com
800-889-0661
Carlson Paving Sales / Parts Department
(253) 875-8000
made
in the USA

CARLSON PAVING PRODUCTS, INC. an Astec Industries Company

18425 50th AVENUE EAST • TACOMA, WA 98446 USA • PH 800.216.2108 • carlsonpavingproducts.com
 Carlson EZ III Screed
Highway Class Screed

DynapacParts.com
800-889-0661

Carlson delivers the perfect touch.

Designing and manufacturing the most award-winning screeds in the industry

Carlson Paving Products, the premier manufacturer of innovative paving solutions

for over 25 years. Partnering with industry leaders and innovative design has helped Carlson Paving
Products become the leader in screed design. From the introduction of flameless heating systems and

DynapacParts.com
wider extension bodies with angle of attack, Carlson has helped change the industry and improve the
quality of the roads we drive on today. Through innovative design concepts like tapered main screeds

800-889-0661
and integrated berm builders, Carlson has increased flow properties and reduced segregation areas
commonly inherent in competitor’s designs. With the addition of heated endgates and vibrating beveled
edgers, Carlson continues to answer the paving industry’s demands for ever-increasing higher-quality
joint standards with safe and effective applications. With an open minded approach and industry-leading
partners, Carlson continues to improve paving standards and ease of application industry-wide.
Carlson delivers the perfect touch.
Electric heat for quality control Laying the perfect mat. Ergonomically-friendly
and operator safety. Carlson’s innovative, adjustable work environment.
Advanced-design heating elements, in direct contact angle-of-attack produces a mat quality Dual control stations
with the upper surface of the main screed plate, deliver consistent with the main screed in and a wide walkway
even, controllable heat. This ensures consistent fluidity texture and density. give operators

DynapacParts.com
and smooth asphalt laydown and helps contractors meet
clean air standards, by getting rid of smoke created by
diesel flame heated screeds. Maintenance costs to repair
Innovative berm
builder adds value and
the ability to work
efficiently and move
safely around the EZ

800-889-0661
warped screed plates and burner boxes are eliminated. versatility. Screeds.
Carlson’s industry-acclaimed,
Front taper design for uniform Crew comfort matters.
adjustable berm builder enables
distribution. contractors to offer economical All EZ Screeds
All EZ Screeds have the patented front taper design, drainage control by creating jointless feature the popular
helping create smoother roads, parking lots and other asphalt curbs and gutters. built-in oven for
high-use surfaces by constantly moving material to the meal preparation,
outside. Cold spots are prevented and even heads of The fully adjustable conveniently
material are maintained for a perfect mat. Screed Plate. located cupholders
and hardy storage.
All EZ Screeds incorporate the
innovative adjustable deck cone
system to extend screed plate lifecycle
2°
through simple adjustments.
2°

Adjustable slide track supports

the heated extensions for paving
wider roads.
The extension support
system (a unique feature SPECIFICATIONS
of the Carlson EZIII
Screed) uses brass Model EZIII-08 EZIII-10 EZIII-LW08
wear plates to maintain
tight control and prevent Standard Paving Width 8 ft. (2.44m) 10 ft. (3.05m) 8 ft. (2.44m)
vertical movement. Extended Paving Width 13 ft. 6 in. (4.11m) 17 ft. (5.18m) 13 ft. 6 in (4.11m)
Maximum Paving Width 19 ft. (5.8m) 24 ft. (7.6m)* 19 ft. (5.8m)
Extension Slope Down 9% 9% 9%
Maximum Berm Height 4 in. (10.16cm) on outside edge, optional 6 in. (15.24cm)
Berm Width Available 12 in. (30.48cm), 18 in. (45.72cm) or 24 in. (60.96cm)
2.5 in. (7.6cm) Positive
Power Crown 1.5 in. (3.8cm) Invert

For more information contact:

DynapacParts.com Walkway Width
Oven
20.5 in. (52.07cm) Hinged
Standard Equipment
120 Volt @ 1200 watts while heating

800-889-0661
Power Outlets Accessory mode provides optional 4800 additional watts for lights
Carlson Paving Sales / Parts Department
Screed Weight 5,200 lbs. 6,000 lbs. 4,500 lbs.
(253) 875-8000
Main Screed Plate Standard .50 in. Hardox 450 (2.7mm)
made
in the USA *Optional bolt on support recommended beyond 22 ft. (6.7m)

CARLSON PAVING PRODUCTS, INC. an Astec Industries Company

18425 50th AVENUE EAST • TACOMA, WA 98446 USA • PH 800.216.2108 • carlsonpavingproducts.com
 Carlson EZ IV Screed
Highway Class Screed

DynapacParts.com
800-889-0661

Carlson delivers the perfect touch.

Designing and manufacturing the most award-winning screeds in the industry

Carlson Paving Products, the premier manufacturer of innovative paving solutions

for over 25 years. Partnering with industry leaders and innovative design has helped Carlson Paving
Products become the leader in screed design. From the introduction of flameless heating systems and

DynapacParts.com
wider extension bodies with angle of attack, Carlson has helped change the industry and improve the
quality of the roads we drive on today. Through innovative design concepts like tapered main screeds

800-889-0661
and integrated berm builders, Carlson has increased flow properties and reduced segregation areas
commonly inherent in competitor’s designs. With the addition of heated endgates and vibrating beveled
edgers, Carlson continues to answer the paving industry’s demands for ever-increasing higher-quality
joint standards with safe and effective applications. With an open minded approach and industry-leading
partners, Carlson continues to improve paving standards and ease of application industry-wide.
Carlson delivers the perfect touch.
Electric heat for quality control Laying the perfect mat. Ergonomically friendly
and operator safety. Carlson’s innovative adjustable angle- work environment.
Advanced-design heating elements, in direct contact of-attack produces a mat quality Dual control stations
with the upper surface of the main screed plate, deliver consistent with the main screed in and a wide walkway
even, controllable heat. This ensures consistent fluidity texture and density. give operators
and smooth asphalt laydown and helps contractors meet the ability to work

DynapacParts.com
clean air standards, by getting rid of smoke created by Innovative berm efficiently and move
diesel flame heated screeds. Maintenance costs to repair builder adds value and safely around the
warped screed plates and burner boxes are eliminated. versatility. EZ Screeds.

800-889-0661
Carlson’s industry-acclaimed,
Front taper design for uniform Crew comfort matters.
adjustable berm builder enables
distribution. contractors to offer economical All EZ Screeds
All EZ Screeds have the patented front taper design, drainage control by creating jointless feature the
helping create smoother roads, parking lots and other asphalt curbs and gutters. popular built-in
high-use surfaces by constantly moving material to the oven for meal
outside. Cold spots are prevented and even heads of The fully adjustable preparation,
material are maintained for a perfect mat. Screed Plate. conveniently
located
All EZ Screeds incorporate the
cupholders and
innovative adjustable deck cone
hardy storage.
system to extend screed plate lifecycle
2°

2°
through simple adjustments.

Adjustable slide track supports

the heated extensions for paving
wider roads.
The extension support SPECIFICATIONS
system (a unique
Model EZIV 2.5m - 4.4m EZIV 8-15 EZIV 10-19
feature of the Carlson
EZIV Screed) uses Standard Paving Width 8 ft. (2.44m) 8 ft. (2.44m) 10 ft. (3.05m)
high-strength chrome
Extended Paving Width 14 ft. 6 in. (4.4m) 15 ft. (4.57m) 19 ft. (5.79m)
rods with adjustable
3.6 ft. Right 4 ft. Right 5 ft. Right
composite bushings to
Extension Length 3 ft. Left 3 ft. Left 4 ft. Left
maintain tight control
and prevent vertical Max. Paving Width with
Bolt-On Extension 19 ft. (5.79m) 19 ft. (5.79m) 26 ft. (7.92m)*
movement.
Vertical Height Adjustment Hydraulic Hydraulic Hydraulic
Extension Slope Down 9% 9% 9%
Maximum Berm Height 4 in. (10.16cm) on outside edge
Berm Width Available 12 in. (30.48cm), 18 in. (45.72cm) or 24 in. (60.96cm)
2.5 in. (64mm) Positive
Power Crown 1.5 in. (38mm) Invert

For more information contact:

DynapacParts.com Walkway Width
Oven
20.5 in. (52.07cm) Hinged
Standard Equipment
120 Volt @ 1200 watts while heating

800-889-0661
Carlson Paving Sales / Parts Department Power Outlets Accessory mode provides optional 4800 additional watts for lights

(253) 875-8000 Screed Weight 6,000 lbs. 6,250 lbs. 7,000 lbs.
Main Screed Plate Standard .50 in. Hardox 450 (2.7mm)
made
in the USA *Optional bolt on support recommended beyond 22 ft. (6.7m)

CARLSON PAVING PRODUCTS, INC. an Astec Industries Company

18425 50th AVENUE EAST • TACOMA, WA 98446 USA • PH 800.216.2108 • carlsonpavingproducts.com
 Carlson WP-810
Windrow Pick-Up Machine

DynapacParts.com
800-889-0661

Great paving demands great craftsmanship.

Designing and manufacturing superior asphalt equipment for

the paving industry.

DynapacParts.com
The Carlson WP-810 Windrow Pick-Up Machine (designed to couple to the front of a hot mix asphalt paver)
transfers hot mix asphalt, or HMA, from windrows laid in the paving track to the paver hopper via its

800-889-0661
elevating conveyor. HMA reblending occurs during pick up and transfer to the paver hopper.

The WP-810 can be adapted for use on almost any highway-class paver, and can be used with or without
a hopper insert unit. The manually-adjustable hitch (supplied as standard) allows distance adjustment
between the WP-810 and the paver to suit various applications.
Great paving demands great craftsmanship
Exclusive Anti-Segreation Features
A front plow and augers provide excellent remix of the material
upon entering the machine. The WP-810 provides even more
anti-segregation with a patented discharge chute design.

DynapacParts.com
Proven and Powerful Conveyor System
All components

800-889-0661
in the WP-810
conveyor system
are engineered
for the longest
life possible. The
WP-810 shown with optional towing package
conveyor speed
can be adjusted
on-the-fly, to SPECIFICATIONS
improve the day- Overall Length 18’
to-day operation of the machine. The conveyor can be switched Overall Height (with exhaust) 11’
into reverse for easy cleanout and/or service.
Travel Width (with casters in) 8’6”

Service Friendly Working Width (with casters out) 12’6”

Operation Weight 19,000 lbs.
The WP-810 was designed with the operator and service
Fuel Tank Capacity 60 gallons
technician in mind. From the swing-out hydraulic oil cooler for
easy cleaning, to the ground-level centrally-located grease banks, Hydraulic Tank Capacity 30 gallons
this machine is all about ease of operation. A key service feature Inlet Opening 96”
is the single-piece hood that opens quickly for full visibility of all Auger Diameter 22”
components. Conveyor Slat Width 42”
Conveyor Slat Height 6”
Ergonomically friendly work
Conveyer Discharge Height 82” - 101”
environment.
Front Tire Size 22” x 10”
Dual-control stations give the operators the ability to work
Rear Tire Size Dual 26” x 7”
efficiently and move safely around the machine. Digitial display
Capacity 800 tons per hour
for engine functions can be customized to user requirements.
Engine 4 cylinder turbo Cat, 127hp@2400rpm

Options
• Wash-down reservoir and pump unit
• Highway towing axle assembly

With Carlson’s policy of continually improving its products,

For more information contact: DynapacParts.com

Carlson Paving Sales / Parts Department
specifications are subject to change without notice. Actual
dimensions, clearances, weights and other specifications may
vary due to fabrication variables, options, or custom engineering.

800-889-0661
For a copy of Carlson’s warranty, please contact your dealer or
(253) 875-8000 Carlson representative. This publication is not a warranty, either
expressed or implied.
made
in the USA

CARLSON PAVING PRODUCTS, INC. an Astec Industries Company

18425 50th AVENUE EAST • TACOMA, WA 98446 USA • PH 800.216.2108 • carlsonpavingproducts.com
 Carlson CP-90
Commercial Class Paver

DynapacParts.com
800-889-0661

Small Paver – Big Results

Answering the industries call for a quality Commercial Class Paver

Adding the Easy Screed to a heavy duty and completely rebuildable Carlson tractor is a winning combination for the
commercial class paving industry. Able to pave driveways or city streets, the CP-90 is the answer to longer lifecycle
ownership and superior performance. Backed by Carlson’s commitment to the industry, the CP-90 is the Small Paver
that produces Big Results.

DynapacParts.com
Partnering with industry leaders and innovative design has helped Carlson Paving Products become the leader in
screed design. From the introduction of flameless heating systems and wider extension bodies with angle of attack,
Carlson has helped change the industry and improve the quality of the roads we drive on today. Through innovative

800-889-0661
design concepts like tapered main screeds and integrated berm builders, Carlson has increased flow properties and
reduced segregation areas commonly inherent in competitor’s designs. With the addition of heated endgates and
vibrating beveled edgers, Carlson continues to answer the paving industry’s demands for ever-increasing higher-
quality joint standards with safe and effective applications. With an open minded approach and industry-leading
partners, Carlson continues to improve paving standards and ease of application industry-wide.
Small Paver – Big Results

TECHNICAL INFORMATION

DynapacParts.com DIMENSIONS

Tractor Width (hopper sides up) 8’ 6” (2.59 m)

800-889-0661 Tractor Width (hopper sides down)

Gage Width (center to center of tracks)
Wheelbase
10’ 1” (3.08 m)
76” (1930 mm)
68” (1727 mm)
Loading Ramp Angle Forward 20°, Backward 15°
Length 13’ 11” (4.24 m)
Length (shipping) 12’ 11” (3.94 m)
Paver Weight 15,900 (7,212 kg)
Screed Weight 2,600 (1,180 kg)
Hopper Inside Width Opening 120” (3.04 m)
Hopper Dump Clearance 27” (.68 m)
Hopper Capacity 7 1/2 Tons (6.8 t)
Conveyor Floor Plate Thickness 3/8” (9.5 mm) Hardox
Auger Flight Thickness 3/4” (19.0 mm)
Auger Speed Max. 100 rpm

CAPACITIES
Fuel Tank 35 gal (132.5 L)
Cooling System Capacity 11 qts. (10 L)
Hydraulic Reservoir Capacity 47 gal. (178 L)
12 volt, negative ground with
Electrical System 95 amp alternator

TRACTION DRIVE
Hydrostatic Direct with 2-Speed Motors.
Speed Selection is infinitely variable in each of the speed ranges:
Paving Range Lo Motor 0 – 160 fpm (48.76 m/min)
Travel Range High Motor 0 – 2.5 mph (4.02 km/hr)
Full reverse in any of the two
Reverse speed ranges
Standard Paving Width 8’ (2.43 m)
Paving Width (Min./Max.) 4’ – 15’ (1.21 m – 4.57 m)

DynapacParts.com
For more information contact:
Carlson Paving Sales / Parts Department
Paving Depth Compacted (Min./Max.) 1/4” – 8” (6 mm – 203 mm)

800-889-0661
(253) 875-8000
made
in the USA

CARLSON PAVING PRODUCTS, INC. an Astec Industries Company

18425 50th AVENUE EAST • TACOMA, WA 98446 USA • PH 800.216.2108 • carlsonpavingproducts.com