ONYXWorks®

NFN Gateway
Embedded
Installation & Operation Manual

D
Document 52306
06/01/07 Rev:
P/N: 52306:D ECN: 06-053
Fire Alarm System Limitations
While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm system—typically made up of smoke detec- bedrooms), smoking in bed, and violent explosions (caused by escap-
tors, heat detectors, manual pull stations, audible warning devices, ing gas, improper storage of flammable materials, etc.).
and a fire alarm control panel with remote notification capability—can Heat detectors do not sense particles of combustion and alarm only
provide early warning of a developing fire. Such a system, however, when heat on their sensors increases at a predetermined rate or
does not assure protection against property damage or loss of life reaches a predetermined level. Rate-of-rise heat detectors may be
resulting from a fire. subject to reduced sensitivity over time. For this reason, the rate-of-
The Manufacturer recommends that smoke and/or heat detectors be rise feature of each detector should be tested at least once per year
located throughout a protected premise following the recommenda- by a qualified fire protection specialist. Heat detectors are designed
tions of the current edition of the National Fire Protection Association to protect property, not life.
Standard 72 (NFPA 72), manufacturer's recommendations, State and IMPORTANT! Smoke detectors must be installed in the same room
local codes, and the recommendations contained in the Guide for as the control panel and in rooms used by the system for the connec-
Proper Use of System Smoke Detectors, which is made available at tion of alarm transmission wiring, communications, signaling, and/or
no charge to all installing dealers. These documents can be found at power. If detectors are not so located, a developing fire may damage
http://www.systemsensor.com/html/applicat.html. the alarm system, crippling its ability to report a fire.
A study by the Federal Emergency Management Agency (an agency Audible warning devices such as bells may not alert people if these
of the United States government) indicated that smoke detectors may devices are located on the other side of closed or partly open doors or
not go off in as many as 35% of all fires. While fire alarm systems are are located on another floor of a building. Any warning device may
designed to provide early warning against fire, they do not guarantee fail to alert people with a disability or those who have recently con-
warning or protection against fire. A fire alarm system may not pro- sumed drugs, alcohol or medication. Please note that:
vide timely or adequate warning, or simply may not function, for a
variety of reasons: • Strobes can, under certain circumstances, cause seizures in people
with conditions such as epilepsy.
Smoke detectors may not sense fire where smoke cannot reach the
• Studies have shown that certain people, even when they hear a fire
detectors such as in chimneys, in or behind walls, on roofs, or on the
alarm signal, do not respond or comprehend the meaning of the signal.
other side of closed doors. Smoke detectors also may not sense a
It is the property owner's responsibility to conduct fire drills and other
fire on another level or floor of a building. A second-floor detector, for training exercise to make people aware of fire alarm signals and
example, may not sense a first-floor or basement fire. instruct them on the proper reaction to alarm signals.
Particles of combustion or “smoke” from a developing fire may not • In rare instances, the sounding of a warning device can cause tempo-
reach the sensing chambers of smoke detectors because: rary or permanent hearing loss.
• Barriers such as closed or partially closed doors, walls, or chimneys A fire alarm system will not operate without any electrical power. If
may inhibit particle or smoke flow. AC power fails, the system will operate from standby batteries only for
• Smoke particles may become “cold,” stratify, and not reach the ceiling a specified time and only if the batteries have been properly main-
or upper walls where detectors are located. tained and replaced regularly.
• Smoke particles may be blown away from detectors by air outlets. Equipment used in the system may not be technically compatible
• Smoke particles may be drawn into air returns before reaching the with the control panel. It is essential to use only equipment listed for
detector. service with your control panel.
The amount of “smoke” present may be insufficient to alarm smoke Telephone lines needed to transmit alarm signals from a premise to a
detectors. Smoke detectors are designed to alarm at various levels of central monitoring station may be out of service or temporarily dis-
smoke density. If such density levels are not created by a developing abled. For added protection against telephone line failure, backup
fire at the location of detectors, the detectors will not go into alarm. radio transmission systems are recommended.
Smoke detectors, even when working properly, have sensing limita- The most common cause of fire alarm malfunction is inadequate
tions. Detectors that have photo-electronic sensing chambers tend to maintenance. To keep the entire fire alarm system in excellent work-
detect smoldering fires better than flaming fires, which have little visi- ing order, ongoing maintenance is required per the manufacturer's
ble smoke. Detectors that have ionizing-type sensing chambers tend recommendations, and UL and NFPA standards. At a minimum, the
to detect fast-flaming fires better than smoldering fires. Because fires requirements of NFPA 72 shall be followed. Environments with large
develop in different ways and are often unpredictable in their growth, amounts of dust, dirt or high air velocity require more frequent mainte-
neither type of detector is necessarily best and a given type of detec- nance. A maintenance agreement should be arranged through the
tor may not provide adequate warning of a fire. local manufacturer's representative. Maintenance should be sched-
uled monthly or as required by National and/or local fire codes and
Smoke detectors cannot be expected to provide adequate warning of should be performed by authorized professional fire alarm installers
fires caused by arson, children playing with matches (especially in

2 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be connected to Like all solid state electronic devices this system may operate errati-
the fire alarm control panel. Disconnect all sources of power before cally or can be damaged when subjected to lightning-induced tran-
servicing. The control unit and associated equipment may be dam- sients. Although no system is completely immune from lightning
aged by removing and/or inserting cards, modules, or interconnecting transients and interferences, proper grounding will reduce susceptibil-
cables while the unit is energized. Do not attempt to install, service, ity. Overhead or outside aerial wiring is not recommended, due to an
or operate this unit until this manual is read and understood. increased susceptibility to nearby lightning strikes. Consult with the
CAUTION - System Reacceptance Test after Software Changes. To Technical Services if any problems are anticipated or encountered.
ensure proper system operation, this product must be tested in accor- Disconnect AC power and batteries prior to removing or inserting cir-
dance with NFPA 72 after any programming operation or change in cuit boards. Failure to do so can damage circuits.
site-specific software. Reacceptance testing is required after any Remove all electronic assemblies prior to any drilling, filing, reaming,
change, addition or deletion of system components, or after any mod- or punching of the enclosure. When possible, make all cable entries
ification, repair or adjustment to system hardware or wiring. from the sides or rear. Before making modifications, verify that they
All components, circuits, system operations, or software functions will not interfere with battery, transformer, and printed circuit board
known to be affected by a change must be 100% tested. In addition, location.
to ensure that other operations are not inadvertently affected, at least Do not tighten screw terminals more than 9 in-lbs. Over-tightening
10% of initiating devices that are not directly affected by the change, may damage threads, resulting in reduced terminal contact pressure
up to a maximum of 50 devices, must also be tested and proper sys- and difficulty with screw terminal removal.
tem operation verified.
Though designed to last many years, system components can fail at
This system meets NFPA requirements for operation at 0°C to 49°C any time. This system contains static-sensitive components. Always
(32°F to 120°F) and at a relative humidity 93% ± 2% RH (non-con- ground yourself with a proper wrist strap before handling any circuits
densing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the so that static charges are removed from the body. Use static-sup-
system's standby batteries and the electronic components may be pressive packaging to protect electronic assemblies removed from
adversely affected by extreme temperature ranges and humidity. the unit.
Therefore, it is recommended that this system and all peripherals be
installed in an environment with a nominal room temperature of 15- Follow the instructions in the installation, operating, and program-
27° C/60-80° F. ming manuals. These instructions must be followed to avoid damage
to the control panel and associated equipment. FACP operation and
Verify that wire sizes are adequate for all initiating and indicating reliability depend upon proper installation by authorized personnel.
device loops. Most devices cannot tolerate more than a 10% I.R.
drop from the specified device voltage.

FCC Warning
WARNING: This equipment generates, uses, and can radi- likely to cause interference, in which case the user will be
ate radio frequency energy and if not installed and used in required to correct the interference at his own expense.
accordance with the instruction manual, may cause inter- Canadian Requirements: This digital apparatus does not
ference to radio communications. It has been tested and exceed the Class A limits for radiation noise emissions
found to comply with the limits for class A computing from digital apparatus set out in the Radio Interference
device pursuant to Subpart B of Part 15 of FCC Rules, Regulations of the Canadian Department of Communica-
which is designed to provide reasonable protection against tions.
such interference when operated in a commercial environ-
ment. Operation of this equipment in a residential area is Le present appareil numerique n'emet pas de bruits radio-
electriques depassant les limites applicables aux appareils
numeriques de la classe A prescrites dans le Reglement
Acclimate Plus™, HARSH™, NOTI•FIRE•NET™, VeriFire™, NION™, NOTIFER Intergrated Systems™ and ONYXWorks™ are trademarks, and
ONYX®, FlashScan®, UniNet®, VIEW®, NOTIFIER® are registered trademarks of Honeywell. Simplex® is registered trademark of Tyco
International Ltd. Echelon® is a registered trademark and LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered trademark of Datapoint
Corporation. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. LEXAN® is a registered trademark of GE Plastics, a subsidiary of
General Electric Company.
©2006 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 3

Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments, you can email
us.
Please include the following information:
• Product name and version number (if applicable)
• Manual page number
• Your comment
Send email messages to:
[email protected]
Please note this email address is for documentation feedback only. If you have any technical issues, please contact
Technical Services.

4 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Table of Contents
Section 1 NFN Gateway Overview........................................................................................... 7
1.1: Product Description .......................................................................................................................................7
Table 1.1 NFN Compatibility Table.......................................................................................................7
1.2: NFN Gateway System Architecture ..............................................................................................................8
Figure 1.1 Direct Panel Gateway System...............................................................................................8
Figure 1.2 ONYXWorks® System Example 1- A Single NFN Network...............................................9
Figure 1.3 ONYXWorks® System Example 2 - Multiple NFN Networks ..........................................10
Figure 1.4 Example NFN Gateway Network .......................................................................................11
1.3: Overall Gateway Configuration Process Flow Diagram .............................................................................13
Figure 1.5 Overall Gateway Configuration Process Flow Diagram.....................................................13
1.4: Agency Listings ...........................................................................................................................................14
1.4.1: Environmental Requirements ............................................................................................................14
1.5: Related Documentation ...............................................................................................................................15
Section 2 NFN Gateway Embedded Installation .................................................................. 17
2.1: Required Equipment ....................................................................................................................................17
2.2: NFN Gateway Installation Overview ..........................................................................................................18
2.2.1: Gateway Installation Process Overview Flow Diagram....................................................................18
Figure 2.1 Gateway Installation Process Flow Diagram ......................................................................18
2.2.2: NFN Gateway PC Board Layout .......................................................................................................19
Figure 2.2 NFN Gateway PC Board.....................................................................................................19
2.3: CAB3/CAB4 Cabinet Installation ...............................................................................................................20
Figure 2.3 CAB-3/CAB-4 Series Installation Document, 15330 .........................................................20
2.4: NFN Gateway Hardware Installation ..........................................................................................................21
Figure 2.4 NFN Gateway Assembly Installation Diagram ..................................................................21
2.5: Network Communication Module Installation ............................................................................................22
Figure 2.5 NCM W/F PC Board Installation Document ......................................................................22
Figure 2.6 NCM-W/F Power Connection ............................................................................................22
2.6: NFN Gateway Power Connection ...............................................................................................................23
Table 2.1 Power Supply Specifications................................................................................................23
Figure 2.7 NFN Gateway Power Connection.......................................................................................23
2.7: NFN Gateway Cable Connections...............................................................................................................24
2.7.1: IP Cable Connections ........................................................................................................................24
Figure 2.8 IP Cable Connection ...........................................................................................................24
2.7.2: Gateway Network Cable Connection ................................................................................................25
Figure 2.9 DB-9 to NUP Connection ...................................................................................................25
2.8: Optional NFN Gateway Voice Paging .........................................................................................................26
2.8.1: About Voice Paging...........................................................................................................................26
2.8.2: Microphone and Public Address Amplifier Connections..................................................................26
Figure 2.10 Gateway Sound Cable Installation....................................................................................26
Figure 2.11 Public Address Amplifier Connections to Gateway Sound Cable....................................27
Section 3 NFN Gateway Configuration ................................................................................. 29
3.1: Gateway Configuration Process Overview Flow Diagram .........................................................................29
Figure 3.1 Gateway Configuration Process Flow Diagram..................................................................29
3.2: Configuration PC Preparation......................................................................................................................30
3.2.1: Install the NFN Config Tool on the Configuration PC .....................................................................30
3.2.2: Connect the Configuration PC to the NFN Gateway ........................................................................30
Figure 3.2 Configuration PC Direct Connection..................................................................................31
Table 3.1 Cross Over Cable (568B) .....................................................................................................31
3.2.3: Add the IP Subnet of the NFN Gateway into the Configuration PC.................................................32
Figure 3.3 TCP-IP Address Window....................................................................................................32
3.3: NFN Gateway Connection...........................................................................................................................33
3.3.1: Default Gateway Connection.............................................................................................................33
3.4: NFN Gateway Configuration Procedure .....................................................................................................34
NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 5
Table of Contents

3.4.1: IP Address Setting .............................................................................................................................34

Figure 3.4 Gateway Node Selection .....................................................................................................34
Figure 3.5 Gateway Login Window .....................................................................................................34
Figure 3.6 Gateway IP Configuration...................................................................................................34
3.4.2: Gateway Settings ...............................................................................................................................35
Figure 3.7 Gateway Mode Setting ........................................................................................................35
Figure 3.8 Gateway NCM Address Setting ..........................................................................................35
3.4.3: Time Settings .....................................................................................................................................36
Figure 3.9 Gateway SNTP and Time Zone Configuration ...................................................................36
Figure 3.10 Gateway Time Settings .....................................................................................................36
Figure 3.11 Gateway Time Settings .....................................................................................................36
3.4.4: Login Password Settings....................................................................................................................37
Figure 3.12 Gateway Login - Change Password Window ...................................................................37
Section 4 NFN Config Tool Reference Information ............................................................. 39
4.1: NFN Config Tool Description......................................................................................................................39
4.2: Property/Value Field Descriptions ...............................................................................................................39
Figure 4.1 NFN Config Tool Field Descriptions..................................................................................39
4.2.1: GATEWAY SETTINGS Fields ........................................................................................................40
4.2.2: IP Configuration Fields......................................................................................................................40
Figure 4.2 NFN Config Tool IP Configuration Property/Value Field Descriptions ............................40
4.2.3: SNTP Configuration Fields ...............................................................................................................40
Figure 4.3 NFN Config Tool SNTP Configuration Property/Value Field Description........................40
4.2.4: Time Zone Configuration Fields .......................................................................................................41
Figure 4.4 NFN Config Tool Time Settings Field Descriptions ..........................................................41
4.2.5: Panel Properties Fields ......................................................................................................................42
Figure 4.5 NFN Config Tool Panel Property/Value Field Descriptions ..............................................42
4.3: Menu Descriptions .......................................................................................................................................43
4.3.1: File .....................................................................................................................................................43
4.3.2: View...................................................................................................................................................43
4.3.3: Tools ..................................................................................................................................................44
4.3.4: Help....................................................................................................................................................44
Index ........................................................................................................................................ 45

6 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Section 1 NFN Gateway Overview

1.1 Product Description

This gateway:
• Serves as a bridge between an ONYXWorks® Workstation or FIRSTVISION™ and a NFN
network.
• It uses the Workstation as the primary reporting station for the NFN network.
• Translates a NFN network’s panel and device data into data that can be interpreted by the
ONYXWorks® Workstation software application or FIRSTVISION™.
• Monitors NFN networks using ARCNET network architecture.
• Is configured using the NFN Config Tool.
The NFN Gateway software application resides on a PC board assembly that is installed inside a
CAB-3/4 series cabinet. It communicates with any ONYXWorks® Workstation software
application or FIRSTVISION™ on the system via an IP connection over Ethernet networks.
The NFN Gateway acts like any other node on a NFN network and is compatible with the following
node types. An * indicates panels that support using a USB or serial cable for the direct
connections.

Table 1.1 NFN Compatibility Table

NFN Node Type Network Board Used

AFP-200 NAM
AFP-300/400 NAM

AFP-1010 SIB-NET

AM2020 SIB-NET
BACnet Gateway NCM-W/F

BACnet Gateway-2 NCM-W/F

DAA

DVC NCM-W/F

NFS-320* NCM-W/F

NFS-640 NCM-W/F
NFS2-640* NCM-W/F

NFS-3030 NCM-W/F

NFS2-3030* NCM-W/F

NFN Web Server NCM-W/F

NFN Web Server-2 NCM-W/F

NCA NCM-W/F

NCA-2* NCM-W/F

NCS NCM-W/F

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 7

NFN Gateway Overview NFN Gateway System Architecture

1.2 NFN Gateway System Architecture

The NFN Gateway assembly connects to a NUP connector on the NCM-W/F PC board which is
connected to the NFN network; the NFN Gateway connects to system via Ethernet cabling.
ONYXWorks® System Architecture Diagrams
An ONYXWorks® system must have at least one capable UL or ULC listed computer, that is
appropriate for use with fire protective signaling units with the ONYXWorks® Workstation
software application installed. A Workstation can monitor or control node points on the NFN
network through the gateway.

Workstation

Ethernet IP
Connection

Gateway
Embedded

Serial Data or USB

Connection

FACP

Figure 1.1 Direct Panel Gateway System

8 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway System Architecture NFN Gateway Overview

IP Network

Workstation Workstation

Gateway
Embedded

NFN Network

FACP FACP FACP

Figure 1.2 ONYXWorks® System Example 1- A Single NFN Network

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 9

NFN Gateway Overview NFN Gateway System Architecture

IP Network

Workstation
Gateway PC
Workstation

Workstation/Echelon
Gateway

Gateway
Embedded
Style 4, 6, or 7
Echelon Network
Wire or Fiber, ULC
Style DCLA, DCLB,
and DCLR

NFN Network NFN Network

NION NION NION

FACP FACP FACP FACP FACP FACP

NOTIFY
PAA

ACT-2
Voice Paging Equipment

XPIQ

Speakers

Figure 1.3 ONYXWorks® System Example 2 - Multiple NFN Networks

10 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway System Architecture NFN Gateway Overview

FIRSTVISION™ System Architecture Diagram

The following figure illustrates a possible NFN network that includes NFN Gateway.

FIRSTVISION

Ethernet (TCP/IP)
Network

Gateway Embedded

NFN Network

FACP FACP FACP

Figure 1.4 Example NFN Gateway Network

NOTE: If if you are connecting NFN Gateway to a NFN Gateway PC and plan on running the
ONYXWorks® Workstation software application also, the Workstation must be set to Supervising
Station Mode (refer to the Workstation manual).

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 11

NFN Gateway Overview NFN Gateway System Architecture

About ONYXWorks® Ethernet Network Installations

The ONYXWorks® Workstation is a Proprietary Supervising Station that has a supervised client
server architecture that communicates over Ethernet (TCP/IP) networks. The IP network can be a
shared bandwidth system that operates over topologies such as an intranet, the Internet, or a frame
relay system. ULC does not allow operation over an Internet connection.
ONYXWorks® clients, in the most basic system, can co-exist on one computer. For more powerful
systems, multiple computers can be networked together over the IP network running multiple
instances of the Workstation software application or other clients and gateways.
If the Workstation or gateway are sharing on-premises communications equipment, the shared
equipment shall be “listed for the purpose”. “Listed for the purpose” has been formally interpreted
by NFPA (Formal Interpretation 72-99-1) for equipment on packet switched networks as being
listed to the requirements applicable to general purpose communications network equipment.
For ULC applications, the Internet cannot be used for either primary or ancillary functionality.

12 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

Overall Gateway Configuration Process Flow Diagram NFN Gateway Overview

1.3 Overall Gateway Configuration Process Flow Diagram

Start

“CAB3/CAB4 Cabinet
Installation” on page 20

Refer to Section 2, “NFN Gateway Embedded Installation”

“NFN Gateway Hardware
Installation” on page 21

“Network Communication
Module Installation” on
page 22

“NFN Gateway Power

Connection” on page 23

“NFN Gateway Cable

Connections” on page 24

“Install the NFN Config “IP Address Setting” on

Tool on the Configuration page 34
PC” on page 30
“Gateway Settings” on
Refer to Section 3, “NFN Gateway Configuration”

page 35

“Connect the
Configuration PC to the “NCM Address Setting”
NFN Gateway” on on page 35
page 30

“Time Settings” on
page 36
“Add the IP Subnet of the
NFN Gateway into the
Configuration PC” on “Login Password
page 32 Settings” on page 37

“Default Gateway
Connection” on page 33 Finished

Figure 1.5 Overall Gateway Configuration Process Flow Diagram

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 13

NFN Gateway Overview Agency Listings

1.4 Agency Listings

NOTE: ONYXWorks® systems work with products that have been certified to comply with the
requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864
9th Edition, as well as products that have not received UL 864 9th Edition certification. Operation
of a UL 864 9th Edition compliant system together with products not tested for UL 864 9th Edition
has not been UL evaluated. Such operation requires the approval of the local Authority Having
Jurisdiction (AHJ).

This product is intended to be installed in accordance with the Local Authority Having Jurisdiction
(LAHJ) and has been investigated to, and found to be in compliance with the following standards
and documents. Before proceeding, the installer should be familiar with them too.
Underwriters Laboratories U.S. Documents
• UL-294: Access Control System Units, Fifth Edition.
• UL-864: Control Units for Fire Protective Signaling Systems, Ninth Edition.
• UL-1076: Proprietary Burglar Alarm Units and Systems, Fifth Edition.
Underwriters Laboratories Canada Documents
• CAN/ULC-S527-99: Standard for Control Units for Fire Alarm Systems.
National Fire Protection Association Standards
• NFPA 70: National Electrical Code.
• NFPA 72: Installation, Maintenance, and Use of Protective Signaling Systems.

WARNING: Installation
! Improper installation, maintenance, and lack of routine testing could result in system malfunction.

1.4.1 Environmental Requirements

This product must be installed in the following environmental conditions:
• Temperature range of 0°C to 49°C (32°F - 120°F).
• 93% humidity non-condensing at 30°C (86°F).

14 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

Related Documentation NFN Gateway Overview

1.5 Related Documentation

The following documentation resources is related to the ONYXWorks® system.
• ONYXWorks® Workstation Manual (P/N 52342)
• ONYXWorks® Configuration Tool (P/N 53038)
• FIRSTVISION™ Configuration Tool (P/N 53035)
• FIRSTVISION™ Installation and Operation Manual (P/N 53034)

NOTE: The contents of this manual are important and must be kept in close proximity of the
installed equipment. If building ownership is changed, this manual including all other testing and
maintenance information must also be passed to the current owner of the facility. A copy of this
manual was shipped with the equipment and is also available from the manufacturer.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 15

NFN Gateway Overview Related Documentation

16 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Section 2 NFN Gateway Embedded Installation

2.1 Required Equipment

The NFN Gateway requires the following:
NFN Gateway Assembly
The following are shipped with the NFN Gateway:
• NFN Gateway PC board (P/N 46173).
• Power supply (P/N 46175) - used for supplying +24VDC to +5VDC to the NFN Gateway PC
board.
• NFN Gateway/Power Supply Mounting Plate (P/N 18541).
• HDD Power connector (P/N 75581) - used for supplying +24VDC to +5VDC to the NFN
Gateway PC board.
• PNET-1 surge suppressor (P/N PNET-1).
• RJ45 to RJ45 standard Ethernet network cable (P/N 75585) - used to connect the NFN
Gateway PC board to PNET-1 surge suppressor.
• DB9 to NUP Cable (P/N 75554) - used to connect the NFN Gateway PC board to an NCM-
W/F board.
• NUP to +24VDC power cable (P/N 75583) - used for supply power to the NCM-W/F board.
• NFN Config Tool.
Network Components
• RJ45 to RJ45 standard Ethernet network cable - customer’s internet or intranet connection to
PNET-1 surge suppressor (supplied by customer).
• ONYXWorks® Workstation (v3.0 or above) or FIRSTVISION™ (v1.4 or above) (sold
separately).
• NFN network - version 5.0 or above (sold separately).
• Network Communication Module: NCM-W/F board - used to facilitate network
communication between the NFN Gateway and NFN network (sold separately).
Cabinet and Hardware (sold separately)
• CAB-3/CAB-4 series cabinet.
• CHS-4L chassis.
Customer Supplied Equipment
• PC to NFN Gateway Ethernet cross over cable - direct connection of the NFN Gateway to a
Configuration PC (refer to “Direct Connection to the Gateway PC Board” on page 31).
• PC - the NFN Configuration Tool installed on it to configure the NFN Gateway.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 17

NFN Gateway Embedded Installation NFN Gateway Installation Overview

2.2 NFN Gateway Installation Overview

CAUTION: Multiple NFN Gateway Installations
! NFN Gateways should be installed and configured one at a time because all NFN Gateway use the
same predefined IP address and node number, therefore when you go to configure the one gateway
it can be found to configure.

2.2.1 Gateway Installation Process Overview Flow Diagram

Start

“CAB3/CAB4 Cabinet
Installation” on page 20

“NFN Gateway Hardware

Installation” on page 21

“Network Communication
Module Installation” on
page 22

“NFN Gateway Power

Connection” on page 23

“NFN Gateway Cable

Connections” on page 24

To “Gateway
Configuration Process
Flow Diagram” on
page 29

Figure 2.1 Gateway Installation Process Flow Diagram

18 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Installation Overview NFN Gateway Embedded Installation

2.2.2 NFN Gateway PC Board Layout

DB9-NUP Connector -
used for operation as
the network connection
to NFN Network
HDD Power
Connector (P1)

RJ45 Ethernet
Connector (CN2)
Reset Button

Figure 2.2 NFN Gateway PC Board

Reset Button
The Reset button is used to cycle power to the PC board. It does not affect the settings made to the
software.
Lithium Battery

NOTE: The replacement of the PC Board’s lithium battery is to be performed by a trained technician.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 19

NFN Gateway Embedded Installation CAB3/CAB4 Cabinet Installation

2.3 CAB3/CAB4 Cabinet Installation

Step 1. Install a new CAB-3/CAB-4 series cabinet according to the requirements of the local
authority having jurisdiction or prepare an existing CAB-3/CAB-4 series cabinet that
houses a supported panel or annunciator. Refer to Table 1.1 on page 7 for list of supported
panels and annunciators.

NOTE: The CAB3/CAB4 cabinet is ordered separately. For installation details, refer to the CAB-
3/CAB-4 Series Installation Document, 15330 and or the panel’s or annunciator’s documentation.

Step 2. After the CAB3/CAB4 cabinet is prepared with the CHS-4L chassis installed, perform the
“NFN Gateway Hardware Installation” on page 21.
CAB-3/CAB-4 Series Cabinets
Product Installation Document

PN 15330:G 05/23/2005 05-310

1 General
All cabinets are fabricated from 16 gauge steel. The cabinet consists of two basic components: a backbox and a locking
door.
The key-locked door is provided with a pin-type hinge, two keys, and the necessary hardware to mount the door to the
backbox. The backbox has been engineered to provide ease-of-entry for the installer. Knockouts are positioned at
numerous points to let the installer bring conduit into the enclosure easily. Doors can be mounted on the left or right-hand
side. The same hinge works in both configurations, so that this choice can be made in the field. The door opens 180°.
Cabinets are available in four (4) sizes, A through D. The outside dimensions are noted on each enclosure diagram. "A"
size accommodates one chassis, a power supply, and two 26 AH batteries; "D" size accommodates four chassis, a power
supply, and two 26 AH batteries. A trim ring option is available for semi-flush mounting. The CAB-3/CAB-4 Series is
compatible with multiple chassis including the CHS-M2, CHS-M3, CHS-4, CHS-4L, CHS-4N, CHS-BH, CHS-PS, CA-1,
and CA-2. Note: CAB-4 series backboxes and doors are sold separately.

2 Before You Begin

The option of mounting doors in either a left/right hand configuration
will aid in installation and service when two control panels are

CAB door RH.wmf

mounted in a confined area or side by side (as shown). In this manner
CAB door LH.wmf

the doors can be opened "barn door" style, permitting an open work
space. Note that in this type of installation it is necessary to leave
enough space between cabinets to insert a key into the locks on the
door frames.
IMPORTANT: Attach the two hinges and two alignment tabs to the
backbox before any equipment is installed. With chassis installed,
space is very limited.
Display Interface Assembly Note: When the door is left-hand
mounted, the Display Interface Assembly (DIA) dress panel cannot be
opened when the door is at less than a 120° angle to the cabinet. If you are using the left-hand mounting option, be sure
that the door can open at least 120°. This is especially important if the cabinet is to be mounted in a closed area, such as a
closet or utility room.

3 Door Assembly Instructions

Hinges can be either left or right hand mounted. The Illustrations and text depict a left hand mounted example. For a right
hand mounting, simply substitute right for left in the instructions.
1. Insert door hinges (A) into the top and bottom slots of the side to be hinged (in this case the LEFT side). Secure the
hinges to the studs in the backbox with the #8 hex nuts provided. Note that the small hole on the outer tab faces
outward.
2. Thread stud (B) into the BOTTOM hinge first. Thread from the bottom up. Place the grounding "star" washer on the
stud. Place the door's lower corner onto this stud. Placing the door on the lower stud first provides a place for the door
to rest while you complete the assembly.
3. Align the door on the backbox, so that the door sits directly under the top hinge. Thread remaining stud (B) into the
TOP hinge and through the hole in the top of the door. Your door should now swing freely.

Figure 2.3 CAB-3/CAB-4 Series Installation Document, 15330

20 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Hardware Installation NFN Gateway Embedded Installation

2.4 NFN Gateway Hardware Installation

Step 1. Install NFN Gateway PC board onto the mounting plate.
Step 2. Install power supply onto the mounting plate.
Step 3. Install PNET-1 onto the mounting plate.
Step 4. Install the mounting plate onto the CHS-4L chassis that is already installed in the
CAB3/CAB-4 cabinet.
Step 5. Ground the PNET-1.
Step 6. You are now ready to perform the “Network Communication Module Installation” on
page 22.

2 1

3
4
6

Figure 2.4 NFN Gateway Assembly Installation Diagram

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 21

NFN Gateway Embedded Installation Network Communication Module Installation

2.5 Network Communication Module Installation

Step 1. Install the type of NCM W/F PC board you will use into the new CAB3/CAB4 cabinet or
an existing panel’s or annunciator’s cabinet.

NOTE: For installation details, refer to the document that ships with NCM board.

Use the Network Control Module PC board configuration that fits your installation needs.
• NCM-W with twisted pair wire.
• NCM-F with fiber-optic cable.
y p y

12 Clintonville Road
Northford, CT 06472-1653 USA
203-484-7161 • FAX 203-484-7118
www.notifier.com
NCM Installation Document
Network Communications Module NCM-W, NCM-F
PN 51533:B 11/29/2005 05-238

1 UL 864 Compliance
1.1 Products Subject to AHJ Approval
This product has been certified to comply with the requirements in the Standard for Control Units and Accessories for Fire
Alarm Systems, UL 864 9th Edition.
The following products have not received UL 864 9th Edition certification and may only be used in retrofit applications.
Operation of the NCM-W, NCM-F with products not tested for UL 864 9th Edition has not been evaluated and may not
comply with NFPA 72 and/or the latest edition of UL 864. These applications will require the approval of the local
Authority Having Jurisdiction (AHJ).
• AM2020/AFP1010
• MIB
• NAM-232

2 Product Overview
The Network Communications Module (NCM) provides a means for connecting specific Notifier fire alarm control
products to NOTI•FIRE•NET™. There are two types of NCMs available: NCM-W for connecting nodes with
twisted-pair wire, and NCM-F for connecting nodes with fiber-optic cable.
In most applications, one NCM is required per NOTI•FIRE•NET™ node (including fire alarm control panels and
network annunciators) . Even though the NCM has two NUP ports, only one may be connected to a NOTI•FIRE•NET™.
node. Except in some DVC applications, do not connect two NCMs via NUP ports (aka “NUP to NUP”).
For instructions on the additional capabilities available with the DVC, refer to the DVC Manual.
• Input power requirements: 24 VDC , 0.11 amps, regulated, power-limited compatible power supply UL/ULC listed
for fire protective signalling use.
• Communications circuit requirements: Refer to the NOTI•FIRE•NET™ Manual (Network Version 4.0 and Higher)
for wiring length and threshold information.

Figure 2.5 NCM W/F PC Board Installation Document

Step 2. After this installation is perform “NFN Gateway Power Connection” on page 23.
When using an NCM-W/F, it can be powered by a panel/annunciators power source or the
supplied NFN gateway’s power supply (Figure 2.6).

NOTE: The NCM-W/F it can be powered by customer supplied external power supply, it should
be UL listed for fire protective signaling systems, power limited and regulated.

Refer to Table 2.1 on page 23 for power supply specifications.

24VDC REF Input

+24VDC Input

Earth
+5VDC Output
5V REF Output Black wire

Red wire P/N 75583

To NCM NUP Port

Figure 2.6 NCM-W/F Power Connection

NOTE: For complete details on powering and connecting an NCM-W/F, refer to the document
that was shipped with it.

22 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Power Connection NFN Gateway Embedded Installation

2.6 NFN Gateway Power Connection

The power supply for the NFN Gateway is a +24VDC to +5VDC unit. It requires +24VDC @ 330
mA nominal and battery backup in accordance with local code requirements.

Table 2.1 Power Supply Specifications

TYPICAL MIN MAX

Input Voltage +24VDC +19VDC +29V

Input Current @ +24VDC 360 mA without NCM

450 mA with NCM

Output Voltage +5V +4.8V +5.2V

Output Current @ +24VDC 1.2 A

24VDC REF Input

+24VDC Input

Earth
+5VDC Output
5V REF Output

The Earth connector

MUST be connected
Red wire to earth ground.

Black wire To Gateway PC Board’s

HDD Power Connector
P/N 75581

Figure 2.7 NFN Gateway Power Connection

Step 1. Connect the power supply to the gateway (Figure 2.7).

Step 2. After the power supply is connected, perform “NFN Gateway Cable Connections” on
page 24.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 23

NFN Gateway Embedded Installation NFN Gateway Cable Connections

2.7 NFN Gateway Cable Connections

2.7.1 IP Cable Connections
This connection is the NFN Gateway to your IP network (Internet or Intranet). The supplied
PNET-1 surge suppressor must be used between the NFN Gateway PC board and your network.
Step 1. Plug one end the RJ45 cable into the NFN Gateway PC board and the other into the square
end of the PNET-1.
Step 2. Connect your IP network RJ45 cable into the round end of PNET-1.
Step 3. After the IP network configuration is made, perform “Gateway Network Cable
Connection” on page 25.

PC Board
Customer Supplied Cable PC board to PNET-1

To Internet or Intranet
PNET-1 surge suppressor

Figure 2.8 IP Cable Connection

NOTE: If you are configuring the NFN Gateway using a PC that is not connected to your IP
network, then you can leave the connection between the PC board and the PNET-1 disconnected
until the gateway configuration is complete (refer to “Connect the Configuration PC to the NFN
Gateway” on page 30.)

24 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Cable Connections NFN Gateway Embedded Installation

2.7.2 Gateway Network Cable Connection

„ DB-9 to NUP Cable Connection
Connecting the NFN Gateway to an NCM-W/F allows the gateway to communicate with devices
on a NFN network.

DB-9 end - connect to EIA-232 port

on PC Board PC Board

NUP end - connect to outer NUP port J2

Connect to an NCM-W/F

DB9 to NUP cable P/N 75554

Figure 2.9 DB-9 to NUP Connection

A DB9 to NUP cable is used to connect between the gateway and NFN network. Connect the cable
between to the NFN Gateway PC board’s DB9 connector and a NCM W/F PC board NUP
connector.
• Use a NCM-W for a twisted pair wire connection.
• NCM-F for a fiber-optic cable connection.
Step 4. After these cable connection are made you should perform “NFN Gateway Configuration”
on page 29.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 25

NFN Gateway Embedded Installation Optional NFN Gateway Voice Paging

2.8 Optional NFN Gateway Voice Paging

2.8.1 About Voice Paging
An ONYXWorks® Workstation with the Voice Paging option enabled sends encrypted streaming
audio over an IP network to nodes on the associated NFN network through the NFN Gateway. A
Voice Paging enabled Workstation sends voice messages to an enabled NFN Gateway, which
transmits the audio through a sound card that is connected to the UL-approved public address
amplifier (NOTIFY-PAA). The amplifier adjusts the sound card’s output to the voltage that is
required by the audio coupling transformer (ACT-2). The audio coupling transformer sends the
low-level signal into a supervised input on a quad intelligent audio transponder (XPIQ).
A logic zone equation configured at the receiving FACP links the general zones that are configured
at the Workstation to the appropriate control devices.
• The public address amplifier and the Workstation must have a common AC power source.
• The public address amplifier can drive up to 250 audio coupling transformers. The strength
and quality of the audio signal is diminished with increased wire length.
• Do not run cable adjacent to, or in the same conduit as 120 volts AC service, “noisy”
electrical circuits that are powering mechanical bells or horns, audio circuits above 25 volts
RMS, motor control circuits, or SCR power circuits.
• Voice Paging takes the lowest priority at the quad intelligent audio transponder. Refer to the
quad intelligent audio transponder manual for more information about priority
configuration.
Refer to the ONYXWorks® Workstation manual for Voice Paging software features.

2.8.2 Microphone and Public Address Amplifier Connections

Emergency and re-location messages should not be used on the Voice Over IP function. This
function is to be used only for general paging.
The NFN Gateway PC board is equipped with on-board sound component that is activated through
its JP5 header. If the Voice Paging option is ordered the NFN Gateway assembly comes with a
sound cable that plugs into the JP5 header. The cable has connectors for CD audio, MIC-IN, LINE-
IN and LINE-OUT. The sound cable provides the connection to the public address amplifier.
Sound Cable Installation
Install the sound cable by connecting it to the JP5 header on the gateway PC board as shown in the
following figure. The sound cable connector that plugs into the JP5 header has a tab on one side.
That tab should face the inside of the PC board when installed properly.
Tab on connector faces
the inside of the PC board
MIC-IN

LINE IN
CD Audio

LINE OUT

JP5

Figure 2.10 Gateway Sound Cable Installation

26 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07
Optional NFN Gateway Voice Paging NFN Gateway Embedded Installation

Microphone Connection
Connect the microphone to the NFN Gateway Sound Cable MIC-IN connector.
Public Address Amplifier Connection

NOTE: The NOTIFY-PAA must be mounted within six feet of the NFN Gateway.

Step 1. Using P/N 75625 audio cable, connect the plug into the LINE-OUT connector of the
sound cable.
Step 2. Connect the bare wires of the 75625 cable to the MUSIC and GND terminals on the public
address amplifier.
Step 3. Use 18AWG-12AWG twisted-pair cable to connect the COM and 25V terminals on the
public address amplifier to the AUDIO IN terminals on the audio coupling transformer.
Step 4. Connect the public address amplifier AC power cord to the primary AC power source.

MIC-IN

To Quad Intelligent Audio Transponder

LINE IN
CD Audio

LINE OUT
Audio Coupling Transformer

P/N 75625

To next Audio
Coupling Transformer

Public Address Amplifier

Figure 2.11 Public Address Amplifier Connections to Gateway Sound Cable

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 27

NFN Gateway Embedded Installation Optional NFN Gateway Voice Paging

28 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Section 3 NFN Gateway Configuration

CAUTION: Multiple NFN Gateway Installations

! NFN Gateways should be installed and configured one at a time because all NFN Gateway use the
same default IP address and node number.

NOTE: ONYXWorks® system (v3.0 or later) or FIRSTVISION™ (v1.4 or later) are required when
installing this NFN Gateway.

3.1 Gateway Configuration Process Overview Flow Diagram

From “Gateway
Installation Process Flow
Diagram” on page 18

“Install the NFN Config “IP Address Setting” on

Tool on the Configuration page 34
PC” on page 30
“Gateway Settings” on
page 35

“Connect the
Configuration PC to the “NCM Address Setting”
NFN Gateway” on on page 35
page 30

“Time Settings” on
page 36
“Add the IP Subnet of the
NFN Gateway into the
Configuration PC” on “Login Password
page 32 Settings” on page 37

“Default Gateway
Connection” on page 33 Finished

Figure 3.1 Gateway Configuration Process Flow Diagram

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 29

NFN Gateway Configuration Configuration PC Preparation

3.2 Configuration PC Preparation

NOTE: You must have completed the installation of the NFN Gateway before you proceed with
this preparation (refer to “NFN Gateway Embedded Installation” on page 17).

A Configuration PC is defined as a PC that has the NFN Config Tool installed on it and it is able to
establish an IP connection with the NFN Gateway.

3.2.1 Install the NFN Config Tool on the Configuration PC

You need to install the entire ONYXWorks® Workstation software application on the Configuration
PC (90 MB disk space). The CD-ROM automatically starts if your Configuration PC is setup to
start CD-ROMs automatically.

3.2.2 Connect the Configuration PC to the NFN Gateway

Use one of the following methods to connect the Configuration PC to the NFN Gateway.
• If the Configuration PC is on your IP network then you already have connected it to the NFN
Gateway if you performed the “IP Cable Connections” on page 24.
Therefore you need to “Add the IP Subnet of the NFN Gateway into the Configuration PC” on
page 32.
• If you are going to use a PC and directly connect it to the gateway then you need to perform a
“Direct Connection to the Gateway PC Board” on page 31.

NOTE: A direct connection requires that a cross over Ethernet cable to be made or purchased
by the customer.

30 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

Configuration PC Preparation NFN Gateway Configuration

Direct Connection to the Gateway PC Board

Step 1. Disconnect the Ethernet Surge Suppressor from the PC board if it is connected.

PC Board

Ethernet Surge Suppressor

Figure 3.2 Configuration PC Direct Connection

Step 2. Connect the cross over cable between the Configuration PC network card’s RJ45
connector and the NFN Gateway PC board’s RJ45 connector (refer to "Cross Over Cable
Specifications").
Step 3. You have completed the connections, you need to “Add the IP Subnet of the NFN
Gateway into the Configuration PC” on page 32.

„ Cross Over Cable Specifications

This cross over cable will be directly connected between the Configuration PC network card’s RJ45
connector and the NFN Gateway PC board’s RJ45 connector.
The cross over cable can be purchased or you can make one. Please use the following information
for the correct pinout requirements for each end of the cable. EIA/TIA wire color-code standard
568B is applicable.

Table 3.1 Cross Over Cable (568B)

RJ45 Pin # RJ45 Pin #

Wire Color Diagram End #1 Wire Color Diagram End #2
(END 1) (END 2)

1 White/Orange 1 White/Green

2 Orange 2 Green

3 White/Green 3 White/Orange

4 Blue 4 Blue

5 White/Blue 5 White/Blue

6 Green 6 Orange

7 White/Brown 7 White/Brown

8 Brown 8 Brown

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 31

NFN Gateway Configuration Configuration PC Preparation

3.2.3 Add the IP Subnet of the NFN Gateway into the

Configuration PC
Use the following steps as a guideline to add the NFN Gateway’s IP Subnet to your Configuration
PC’s IP Subnet.
Step 1. Start >Control Panel and then select Network Connections. The Network Connection
window displays.
Step 2. Right click on Local Area Connection and select Properties from the list of choices. The
Local Area Connections Properties window displays.
Step 3. Use the side scroll to display the Internet Protocol (TCP/IP) entry and then click on it.
Step 4. Click on the Properties button. The Internet Protocol (TCP/IP) Properties window
displays.
Step 5. Select the Advanced button. The Advanced TCP/IP Settings window displays.
Step 6. Click on the Add button. The TCP/IP Address window displays

Figure 3.3 TCP-IP Address Window

Step 7. Type in a Configuration PC IP address value for the following:

• IP address (192.168.1.X) where X can be any value except 1 or 3. The gateway
default IP values are:
• IP Address: 192.168.1.2
• Subnet Mask: 255.255.255.0
• Gateway: 0.0.0.0
Step 8. Click the Add button.
Step 9. Close all remaining open windows. You have completed adding the NFN Gateway
address to your Configuration PC’s list of IP addresses.
Step 10. You are now ready to perform the “Default Gateway Connection” on page 33.

32 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Connection NFN Gateway Configuration

3.3 NFN Gateway Connection

NOTE: The Configuration PC must have been prepared before proceeding with these steps;
refer to “Configuration PC Preparation” on page 30.

3.3.1 Default Gateway Connection

Step 1. Start the NFN Config Tool; select Start >Programs >Facilities Monitoring >NFN Config
Tool.
Step 2. Click on the Address fields down arrow and then select the default gateway from the list
of choices. The NFN Config Tool auto detects and loads the default gateway (default
node number is 240).
• Panels connected to the gateway are displayed.
• Status messages are displayed at the bottom the window.
Step 3. The NFN Gateway has a default IP address and you need to change it so it will be added
onto your IP network so perform the “NFN Gateway Configuration Procedure” on
page 34.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 33

NFN Gateway Configuration NFN Gateway Configuration Procedure

3.4 NFN Gateway Configuration Procedure

NOTE: The “NFN Gateway Connection” on page 33 must have done before proceeding with
these steps.

3.4.1 IP Address Setting

Step 1. Select the highest level entry in the Nodes list column hierarchy.

Figure 3.4 Gateway Node Selection

Step 2. Select File >Login to gain editing control of the selected gateway. The Gateway Login
window displays.

Figure 3.5 Gateway Login Window

Step 3. Type in the gateway password and then click the OK button. The default password is
00000000 (eight zeros). The Property fields now display an asterisk next to the fields that
can be edited.
Step 4. If a IP router is NOT being used skip this step.
a. Click on the Value field adjacent to Gateway Property and then type in the address the
router will be using on your IP network.
b. Press the keyboard enter key.
Step 5. Change the default NFN Gateway IP address so it will be added onto your IP network.

Figure 3.6 Gateway IP Configuration

a. Click on the IP Configuration entry in the Nodes column.

b. Click on the Value field adjacent to IP Address Property and then type in the address
the NFN Gateway will be using on your IP network.
c. Press the keyboard enter key.
d. Click in the Value field adjacent to Subnet Mask Property and then type in the subnet
address of the NFN Gateway.
e. Press the keyboard enter key.
Step 6. Select View >Refresh Gateway List.
Step 7. Click on the Address fields down arrow and then select the new gateway address from the
list of choices.
Step 8. Now you need to perform “Gateway Settings” on page 35.

34 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Configuration Procedure NFN Gateway Configuration

3.4.2 Gateway Settings

Mode Setting
The NFN Config Tool is used to set the NFN Gateway’s operation mode.
Step 1. Login to the gateway; select File >Login. The Gateway Login window displays.
Step 2. Type in the gateway password and then click the OK button. The default password is
00000000 (eight zeros).
Step 3. Select the highest level entry in the Nodes list column hierarchy. The gateway’s Property
and Value information displays.
Step 4. Click in the Value field adjacent to Mode Property to display the list of choices, and then
select the desired mode.

Figure 3.7 Gateway Mode Setting

Step 5. Now you need to perform "NCM Address Setting".

NCM Address Setting
Step 6. Click in the Value field adjacent to NCM Address Property and then type in the address.

Figure 3.8 Gateway NCM Address Setting

Step 7. Now you need to perform “Time Settings” on page 36.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 35

NFN Gateway Configuration NFN Gateway Configuration Procedure

3.4.3 Time Settings

The time settings consists of setting the SNTP server address which dictates GMT (Greenwich
Mean Time) for your network and then setting up the Time Zone Configuration fields to
synchronize the gateway to GMT of the SNTP Server.
SNTP Configuration
Step 1. Select the highest level entry in the Nodes list column hierarchy.

Figure 3.9 Gateway SNTP and Time Zone Configuration

Step 2. Click on the SNTP Configuration entry in the Nodes column.

Figure 3.10 Gateway Time Settings

Step 3. Click in the Value field adjacent to SNTP Server Address Property and then type in the
address of the server.
Step 4. Press the keyboard enter key.
Time Zone Configuration
Step 5. Click on the Time Zone Configuration entry in the Nodes column.

Figure 3.11 Gateway Time Settings

Step 6. Click in the Value field adjacent to GMT Minute Offset Property, type in the entry, and
then press the keyboard enter key.
The GMT Minute Offset is to used synchronize the time of day between the gateway and
SNPT Server.
• Use this formula to determine the setting: the US Central Time is minus 6 hours
from GMT, therefore your calculation would be -6 (hours) x 60 (minutes) = -360
minutes.
Step 7. Click in the Value field adjacent to Observe DST and then select True if you want the
gateway to automatically increment or decrement time of day according to Time Zone
Reference setting.

36 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

NFN Gateway Configuration Procedure NFN Gateway Configuration

Step 8. Click in the Value field adjacent to Time Zone References field and then select from these
choices:
• US Standard - When selected the DST Begin and DST End settings are automatically
populated with the appropriate settings.
• EU Standard - When selected the DST Begin and DST End settings are automatically
populated with the appropriate settings.
• Custom - When selected you are require perform DST Begin and DST End settings.
Refer to “DST Begin/DST End” on page 41.
Step 9. Now you need to perform “Login Password Settings” on page 37.

3.4.4 Login Password Settings

The first time the gateway is started the factory default password is used (00000000 - eight zeros),
after the initial configuration it is highly recommended that you change the password.
Step 1. Select Tools >Set Gateway Password. The Gateway Login (change password) window
displays.

Figure 3.12 Gateway Login - Change Password Window

Step 2. Type in the current password in the Password field.

• Passwords are case-sensitive.
• Alpha and numeric characters are supported.
• 1 character minimum and 8 character maximum.
Step 3. Type in a new password in the New Password field.
Step 4. Type in the new password again in the Re-Enter New Password field.
Step 5. Click the OK button to complete the password change.
You have completed "NFN Gateway Configuration" if you followed the procedures in
these section in this order:
• “Configuration PC Preparation” on page 30.
• “NFN Gateway Connection” on page 33.
• “NFN Gateway Configuration Procedure” on page 34.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 37

NFN Gateway Configuration NFN Gateway Configuration Procedure

38 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Section 4 NFN Config Tool Reference Information

4.1 NFN Config Tool Description

The NFN Config Tool interface is used to display configuration information about NFN network
and the NFN Gateway.
The NFN Config Tool uses an Windows Explorer-style collapsible/expandable Nodes list. The
PROPERTY/VALUE columns display information about the selection made in the Nodes list
Property fields that are preceded with an asterisk mean the Value adjacent to it can be modified in
some way.

4.2 Property/Value Field Descriptions

The NFN Config Tool window displays configuration information about the gateway and the NFN
network the gateway is monitoring. When logged into the gateway using a password you can
change settings for any field that has asterik (*) preceding the field’s name.

Figure 4.1 NFN Config Tool Field Descriptions

Version - Displays the gateway’s version.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 39

NFN Config Tool Reference Information Property/Value Field Descriptions

4.2.1 GATEWAY SETTINGS Fields

• Gateway Label - The name entered will only display on the NFN Network.
• Mode - Is used to set gateway’s mode. These are the choices:
• SUP - (Supervising Station Mode) In this mode the ONYXWorks® system supports up to 99
gateways and multiple Workstations.
• FCC - (Fire Command Center) In this mode there is always one Workstation and one NFN
Gateway.
• DCC - (Display and Command Center) This mode is an extension of FCC mode.
• NCM Address - Is used to set the node address of the NFN Gateway.
• Trouble Reminder - If set to True a trouble reminder message is issued across the network
every 24 hours at 11:00 AM; if there is an active trouble on that network.
• Audio - Is used to enable the audio option if installed.
• Channel A and Channel B Threshold - Are set according to the determined amount of network
noise that is present in the network. High is used when the most noise is present and filter that
noise accordingly.
• Style 7 - If set to True Style 7 is used, if set to False Style 4 is used.
• COMM Port - Is used to specify which port the NFN Gateway uses to communicate with
NCM.

4.2.2 IP Configuration Fields

Figure 4.2 NFN Config Tool IP Configuration Property/Value Field Descriptions

• IP Address - Is used to set the IP address of the NFN Gateway on your IP network.
• Subnet Mask - Is used to set the Subnet of your IP network.
• Gateway - Is used to set the IP address of the default gateway.

4.2.3 SNTP Configuration Fields

Figure 4.3 NFN Config Tool SNTP Configuration Property/Value Field Description

SNPT Server Address - (Simple Network Time Protocol) Is used set the address of the SNPT
server. The NFN Gateway retrieves the SNTP server’s GMT (Greenwich Mean Time). Refer to
the “Time Zone Configuration Fields” on page 41.

40 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

Property/Value Field Descriptions NFN Config Tool Reference Information

4.2.4 Time Zone Configuration Fields

Figure 4.4 NFN Config Tool Time Settings Field Descriptions

GMT Reference (Greenwich Mean Time)

GMT Minute Offset - Is used to synchronize the time of day between the gateway and SNTP Server
("SNTP Configuration Fields"). If the gateway is located in the US Central Time zone and the
server is too then type in -360. The US Central Time is minus 6 hours from GMT, therefore your
calculation would be -6 (hours) x 60 (minutes) = -360 minutes.
DST Reference
• Observe DST - If set to True the gateway will use the time of day set in Time Zone Reference
field.
• Time Zone Reference - Is used to set the time zone standard. The choices are:
• US Standard - When selected the DST Begin and DST End settings are automatically
populated with the appropriate settings.
• EU Standard - When selected the DST Begin and DST End settings are automatically
populated with the appropriate settings.
• Custom - If selected requires that DST Begin and DST End settings be made.
DST Begin/DST End

NOTE: These fields only need to be modified if Custom has been selected in the Time Zone
Reference field.

To make the settings for the 1st Sunday of March make the following settings in these fields:
• Series Reference - Select 1st from the list of choices.
• Day of Week - Select Sunday from the list of choices.
• Month - Select March from the list of choices.
• Hour - Is used set the hour of the day to begin/end DST time change.
• Hour Reference - Is used set whether the Hour setting is according to Local Time or GMT.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 41

NFN Config Tool Reference Information Property/Value Field Descriptions

4.2.5 Panel Properties Fields

Figure 4.5 NFN Config Tool Panel Property/Value Field Descriptions

PANEL PROPERTIES
Node - Is used to change the NFN network address of the panel.
VERSIONS
If the NCM Version field is displayed in red, then the version doesn’t match the Local Node entry.

NOTE: The NCM version for panel must match the NCM version displayed in the Local Node
entry. When it does not match the non-matching version is displayed as a red entry. Contact
Technical Services for assistance in acquiring the correct version.

42 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

Menu Descriptions NFN Config Tool Reference Information

4.3 Menu Descriptions

4.3.1 File
• Login... - Is used to gain editing control over the gateway. The factory default password is
00000000 (eight zeros). Refer to “Login Password Settings” on page 37.
• Reboot Gateway - Restarts the gateway on its NFN network.
• Exit - Closes the NFN Config Tool window.

4.3.2 View
All these choices display read only information windows, no editing can be done on the
information displayed from these windows.
• Refresh Gateway List - Used to generate a new list of gateways that will be available and
displayed when the NFN Config Tool’s Address field down arrow is clicked.
• Refresh Nodes List - Used to ping the nodes connected to the current gateway and display their
information.
• Node Table - Displays all the nodes connected to the gateway and their respective version
information.

NOTE: The NCM version for panel must match the NCM version displayed in the Local Node
entry. When it does not match the non-matching version is displayed as a red entry. Contact
Technical Services for assistance in acquiring the correct version. Also panels that do not use an
NCM are displayed as a red entry.

CAUTION: NCM Version

! NCM versions that do not match will result in an unstable NFN network.

• Connected Clients - Used to display a window which lists the clients that are connected to the
gateway.

NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 43

NFN Config Tool Reference Information Menu Descriptions

4.3.3 Tools
Some menu choices are only displayed when a relative selection is made in Nodes list column.
Right click options are also available for the selection made in the Nodes list column.
• Delete Node - Is used to remove a node from the gateway. The Node must be offline before it
can be deleted.
• Auto Detect Nodes - Is used to force the gateway to detect nodes on the NFN network. The
gateway searches for all online nodes on the NFN network.
• Set Gateway Password - Refer to “Login Password Settings” on page 37.

4.3.4 Help
• About - Display version information.

44 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Index
A Hardware Installation 21
IP cable connection 24
Architecture
mode 35
Gateway System 8
multiple 29
Audio 40
Optional Voice Paging 26
Auto Detect Nodes 44
Power Connection 23
Power supply part number 17
C product description 7
Cabinet Installation 20 Required Equipment 17
change password 37 Subnet Mask Address 32
Channel A Threshold 40 Gateway Config Tool
Channel B Threshold 40 field descriptions 39
COMM Port 40 Gateway Installation
Configuration PC 30 Overview 18
connections 30 Gateway Label 40
direct connection 31 Gateway PC board
Configuration Tool layout 19
disk space 30 part number 17
installation 30 Gateway System Architecture 8
GMT 36
D GMT Minute Offset 36, 41
GMT Reference 41
DB9 to NUP Cable 17
DB-9 to NUP Cable Connection 25
DCC 40 H
Delete Node 44 HDD Power connector 17
Documentation 15 Help menu
DST Begin 41 descriptions 44
DST End 41
DST Reference 41 I
Installation
E Environmental Conditions 14
EIA/TIA wire color-code standard 31 IP Address 40
Ethernet cross over cable 17
specifications 31 L
Ethernet Network
listed for the purpose 12
about 12
Login 43
Ethernet network cable 17

F M
Mode 40
FCC 40
fiber-optic cable 22
File menu N
descriptions 43 NCM Address 40
NCM PC board 22
G power connection 22
NCM Version
Gateway 40
red display 42
assembly 17
Network Cable Connection 25
Assembly Installation Diagram 21
Network Communication Module Installation 22
configuration 29
Network Interface PC Board 17
Configuration Procedure 34
Node Table 43
default IP Address 32
NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 45
 Index

NUP to +24VDC power cable 17

O
Observe DST 41

P
password change 37
PNET-1 17
power supply
input current 23
input voltage 23
maximum voltage 23
minimum voltage 23
mounting plate part number 17
output current 23
output voltage 23
Proprietary Supervising Station 12
Public Address Amplifier Connection 27

R
Reboot Gateway 43
Refresh Gateway List 43
Refresh Nodes List 43

S
Set Gateway Password 44
SNPT Server Address 40
Sound Cable 26
Style 7 40
Subnet Mask 40
SUP 40

T
Time Zone Reference 41
Custom 41
EU Standard 41
US Standard 41
Tools menu
descriptions 44
Trouble Reminder 40
twisted pair wire 22

U
ULC 12

V
Version 39
View menu
descriptions 43

46 NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07

 Limited Warranty
Honeywell International Inc. warrants products manufactured by
it to be free from defects in materials and workmanship for
eighteen (18) months from the date of manufacture, under normal
use and service. Products are date stamped at time of
manufacture. The sole and exclusive obligation of Honeywell
International Inc. is to repair or replace, at its option, free of charge
for parts and labor, any part that is defective in materials or
workmanship under normal use and service. All returns for credit
are subject to inspection and testing at the factory before actual
determination is made to allow credit. Honeywell International
Inc. does not warrant products not manufactured by it, but assigns
to the purchaser any warranty extended by the manufacturer of
such products. This warranty is void if the product is altered or
repaired by anyone other than Honeywell International Inc. or as
expressly authorized by Honeywell International Inc. in writing, or
is serviced by anyone other than Honeywell International Inc. or
its authorized distributors. This warranty is also void if there is a
failure to maintain the products and systems in which they operate
in a proper and workable manner. In case of defect, secure a
Return Material Authorization form from our Return Authorization
Department.
This writing constitutes the only warranty made by Honeywell
International Inc., with respect to its products. Honeywell
International Inc., does not represent that its products will prevent
any loss by fire or otherwise, or that its products will in all cases
provide the protection for which they are installed or intended.
Buyer acknowledges that Honeywell International Inc., is not an
insurer and assumes no risk for loss or damages or the cost of any
inconvenience, transportation damage, misuse, abuse, accident or
similar incident.
HONEYWELL INTERNATIONAL INC. GIVES NO WARRANTY,
EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR
ANY PARTICULAR PURPOSE, OR OTHERWISE WHICH
EXTENDS BEYOND THE DESCRIPTION ON THE FACE
HEREOF. UNDER NO CIRCUMSTANCES SHALL HONEYWELL
INTERNATIONAL INC. BE LIABLE FOR ANY LOSS OF OR
DAMAGE TO PROPERTY, DIRECT, INCIDENTAL OR
CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR
INABILITY TO USE HONEYWELL INTERNATIONAL INC.’S
PRODUCTS. FURTHERMORE, HONEYWELL INTERNATIONAL
INC. SHALL NOT BE LIABLE FOR ANY PERSONAL INJURY OR
DEATH WHICH MAY ARISE IN THE COURSE OF, OR AS A
RESULT OF, PERSONAL, COMMERCIAL OR INDUSTRIAL USE
OF ITS PRODUCTS.

FIRSTVISION™ - Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07 47

 World Headquarters
12 Clintonville Road
Northford, CT 06472-1610 USA
203-484-7161
fax 203-484-7118

www.notifier.com