Scribd
Upload
120 views3 pages

Výměna Žárovky Volvo XC70

This document provides instructions for removing and replacing the front headlamp on a V70 vehicle from 2000-2008. It describes disconnecting the headlamp wiring connectors, removing mounting screws, and pulling out the headlamp casing. Instructions are also given for installing the new headlamp, including positioning it, threading in screws, and reattaching wiring connectors. Additional information is provided for replacing bulbs or addressing misting problems.

Uploaded by

K P
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
120 views3 pages

Výměna Žárovky Volvo XC70

This document provides instructions for removing and replacing the front headlamp on a V70 vehicle from 2000-2008. It describes disconnecting the headlamp wiring connectors, removing mounting screws, and pulling out the headlamp casing. Instructions are also given for installing the new headlamp, including positioning it, threading in screws, and reattaching wiring connectors. Additional information is provided for replacing bulbs or addressing misting problems.

Uploaded by

K P
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

35: Lighting, front Stránka č.

1 z 3

35: Lighting, front

V70 (00-08), 2001, B5244T3, M58, YV1SW58K311042259, 042259

20/10/2015 PRINT
35: Lighting, front
Headlamp / bulb,
replacing
Removal
Removing the
headlamp
Switch off the ignition
Set the switch for external
lighting to zero
Remove the nut from the
headlamp wiper
Remove the headlamp wiper
Remove the bumper cover
on the relevant side. Remove
the clips for the grille. See
Casing
Remove the upper screws
from the guide for the
bumper cover
Remove the lower front
screw. Slacken off the rear
screw.
Tension the guide. Remove
the screw on the outside of
the headlamp
Carefully tension the casing.
Remove the innermost screw
from the headlamp
Remove the uppermost
screws from the headlamp
Apply tape as protection
above the casing at the
headlamp.

Carefully pry out the casing.


Position the lower edge of
the end of the casing on the
guide. Hold the cover in
position
Release the headlamp
Pull off the washer hose
Separate and remove the
connectors
Remove the headlamp
Remove the headlamp wiper
motor. See Motor, headlamp
wiper, replacing .

Other

http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 20.10.2015
35: Lighting, front Stránka č. 2 z 3

information
To replace the
bulb. See Bulb,
headlamp,
replacing
If there are
misting
problems in
the headlamp.
See If misting
problems
arise .
1. Indicator lamps
2. Parking lamps
3. Low beam
4. High beam.

Installation
Installing the
headlamp

Install the
headlamp
wiper motor.
See Motor,
headlamp
wiper,
replacing
Position the
headlamp
Position the
washer hose
through the
hole on the
bracket for the
wiper motor
Pull out the top
edge of the
casing. Position
the headlamp
Thread in the
upper screws
Check the
position of the
air bleed hoses
Pull the casing
down from the
guide
Thread in the
outer and inner
screws

http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 20.10.2015
35: Lighting, front Stránka č. 3 z 3

Press in the
headlamp.
Tighten the
upper screws
Tighten the
outer and inner
screws
Install the
holder and
guide for the
cover
Install the
bumper cover.
See Casing
Install the
headlamp
wiper arm
Install the nut
Check and
adjust the
headlamp
beam. See
Headlamps,
aligning .
20/10/2015 PRINT

http://localhost/Vida/jsp/information/xml/xmlDocPrintPreview.jsp 20.10.2015

You might also like