(108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.

3” PANTONE 295U 06/16/2012

English 108A

OWNER’S MANUAL IMPORTANT

SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.

Krystal Clear™
Model 636T Filter Pump
220 - 240 V~, 50 Hz, 165 W
Hmax 1.0 m, H min 0.19 m, IPX5
Max. Water Temperature 35 °C

For illustrative purposes only.

Don’t forget to try these other fine Intex products: pools,

pool accessories, inflatable pools and in-home toys, airbeds
and boats available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change specifications and appearance, which may
result in updates to the instruction manual, without notice.

©2012 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.- Intex
Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte
vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/
Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in
Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex
Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne
par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V., Venneveld 9, 4705 RR
Roosendaal – The Netherlands
108-*A*-R0-1306
 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

TABLE OF CONTENTS
Warnings.......................................................................... 3

Parts List & Reference.................................................... 4-6

Setup Instructions......................................................... 7-10

Operating Instructions.................................................... 11

Operating Time Table...................................................... 12

Maintenance..................................................................... 13-14

Pool Care and Chemicals............................................... 14

Long Term Storage.......................................................... 14

Troubleshooting Guide................................................... 15

Common Pool Problems................................................. 16

General Aquatic Safety................................................... 17

Limited Warranty............................................................. 18

SAVE THESE INSTRUCTIONS Page 2

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

IMPORTANT SAFETY RULES

SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.

READ AND FOLLOW ALL INSTRUCTIONS

WARNING
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge. They
must at all times be supervised by a knowledgeable and experienced adult
responsible for their safety.
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,
which has a maximum rate of 30mA. Do not use a portable residual current device
(PRCD).
• Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The plug must be accessible after produc­­­t is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
• Keep this product more than 2m away from the pool (For France only).
• Keep the plug of this product more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on
it and accessing the pool.
• Do not operate this product when the pool is occupied.
• This product is for use with storable pools only. Do not use with permanently
installed pools. A storable pool is constructed so that it may be readily
disassembled for storage and reassembled to its original configuration.
• This product is intended to be used only for the purposes described in the manual!

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN

PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.

SAVE THESE INSTRUCTIONS Page 3

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

PARTS LIST
PARTS LIST
1 2 3

4 5 6

7 8 9

10 11 12

13 14

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

SAVE THESE INSTRUCTIONS Page 4

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

PARTS REFERENCE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.

1
2
3

3 2

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

REF. NO. DESCRIPTION QTY. ­­­­­­SPARE PART NO.

1 THREADED FILTER HOUSING COLLAR 1 10749
2 AIR RELEASE VALVE/SEDIMENT RELEASE VALVE 2 10460
3 VALVE O-RING 2 10264
4 FILTER HOUSING COVER 1 10750
5 FILTER HOUSING O-RING 1 10325
6 FILTER CARTRIDGE (59900) 1
7 PUMP HOSE WITH NUTS 2 10493 (FR: 10494)

When ordering parts, be sure to quote the model number and part numbers.

SAVE THESE INSTRUCTIONS Page 5

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

PARTS REFERENCE
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.

10 11 12 13 14

10 11 12 13

NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.

REF. NO. DESCRIPTION QTY. ­­­­­­SPARE PART NO.

8 PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED) 2 10747
9 HOSE O-RING 10262
10 STEP WASHER 10745
11 STRAINER NUT 2 10256
12 FLAT STRAINER RUBBER WASHER 2 10255
13 THREADED STRAINER CONNECTOR 2 11235
14 ADJUSTABLE POOL INLET NOZZLE 1 11074

When ordering parts, be sure to quote the model number and part numbers.

SAVE THESE INSTRUCTIONS Page 6

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

SETUP INSTRUCTIONS
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP

The strainer grid prevents large objects from jamming and/or damaging the
filter pump. The plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. If your pool
has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The parts numbers here onward, refer to the
parts depicted in the Parts List section of this manual. To install, do the
following:

1. In a counter-clockwise motion unscrew 1

plunger valve union from the threaded 2
strainer connector (13) (see drawing 1).
Be careful not to lose the step rubber
washer (10). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew 1
the strainer nut (11) from the threaded
connector (13). Leave the flat
washer (12) on the connector (13). 2
INSIDE
3. Install the strainer and plunger valve at the LINER WALL
lower position of pool outlet (marked "+").
From the inside of the pool liner insert
the connector (13) into one of the
pre-cut holes with the washer remaining
on the connector to be placed against
11 12 13
the inside of the liner wall.
4. Before assembly, lubricate the threads
with a petroleum jelly. Then, with the flat
side of the strainer nut (11) facing the 3
outside wall of the liner in a clockwise
motion screw the strainer nut (11) back 1
onto the threaded connector (13) (see
drawing 2).
5. Finger tighten the strainer nut (11) onto
the threaded connector (13). 2
6. Grasp the plunger valve assembly. Make
sure the step washer (10) is in place.
7. In a clockwise motion screw the plunger 4
valve union back onto the threaded
connector (13) (see drawing 3).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during INSIDE
LINER WALL
filling of the pool (see drawing 4).

SAVE THESE INSTRUCTIONS Page 7

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

SETUP INSTRUCTIONS
POOL INLET - NOZZLE & PLUNGER VALVE SETUP

1. In a counter-clockwise motion unscrew 5

2
plunger valve union from the threaded
strainer connector (13) (see drawing 5).
Be careful not to lose the step rubber
washer (10). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew 1
the strainer nut (11) from the threaded
connector (13). Leave the flat
washer (12) on the connector (13). INSIDE 6
3. Install the nozzle and plunger valve at the LINER WALL
upper position of the pool inlet. From the
inside of the pool liner insert the
connector (13) into one of the pre-cut
holes with the washer remaining on the
connector to be placed against the 11 12 13 14
inside of the liner wall.
4. Before assembly, lubricate the threads
with a petroleum jelly. Then, with the flat 7
side of the strainer nut (11) facing the
1
outside wall of the liner in a clockwise
motion screw the strainer nut (11) back
onto the threaded connector (13) (see
drawing 6).
2
5. Finger tighten the adjustable pool inlet
nozzle (14) and the strainer nut (11) onto
the threaded connector (13).
6. Grasp the plunger valve assembly. Make 8
sure the step washer (10) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (13) (see drawing 7).
8. In a clockwise motion turn the plunger INSIDE
valve handle to close position. Ensure the LINER WALL
plunger valve is securely closed. This will
prevent water from flowing out during
filling of the pool (see drawing 8). 9
9. Adjust the direction of the nozzle head Pool
pointing away from the pool outlet for a
better circulation result (see drawing 9).
10. The pool liner is now ready to be filled
with water. Consult the WATER
FLOW
above-ground-pool owner’s manual for
the filling instructions.

SAVE THESE INSTRUCTIONS Page 8

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

SETUP INSTRUCTIONS
FILTER PUMP HOSE CONNECTION SETUP
1. Remove the Krystal Clear™ filter pump and hoses from the packaging.
2. Place the filter pump in such a manner, that you can easily assemble the
hose (7) connections to the plunger valve.
Note: Some regional regulations may require the filter pump to be
mounted on a stationary platform. There are two mounting holes located
in the pump base for this reason. Consult your local authorities for
filter-pump mounting requirements.
3. Grasp the two pump hoses (7) and connect the hose nuts to the filter pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (1)
from the filter housing. Place it in a safe place.
5. The filter pump is an airtight system. Turn the top air release valve (2) once
or twice in a counter-clockwise motion. DO NOT remove the air release
valve from the top cover, as water will expel with force if the motor is
turned on. This may cause injury.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is
inside the housing. If yes, replace the cover, finger tighten the housing
collar (1) back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the
housing to be sure that water does not leak out.
8. When the pool is filled connect the hose from the bottom of the filter housing to
the highest strainer assembly. You will find the hose connection at the bottom
of the plunger valve assembly. ­­­Use the hose nut to attach the hose.
9. Connect the second hose which is fixed to the middle of the motor housing to
the remaining liner connection.

WARNING
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.

WATER LEVEL
PLUNGER VALVE
ASSEMBLY
FILTER HOUSING HOSE NUT ADJUSTABLE POOL
COVER INLET NOZZLE
OUTLET HOSE
AIR RELEASE INSIDE LINER
VALVE WALL
THREADED FILTER
HOUSING COLLAR
MOTOR THREADED
HOUSING STRAINER
FLOW

FILTER CARTRIDGE CONNECTOR

INSIDE
ER
AT

HOSE W
O-RING
OW
FL
ER
WAT

HOSE O-RING INLET HOSE OUTSIDE LINER

WALL
POWER CORD
(ILLUSTRATION NOT TO SCALE)

The installation instruction shall provide information on requirements specified for

the electrical installation and shall include reference to national wiring rules.

SAVE THESE INSTRUCTIONS Page 9

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

SETUP INSTRUCTIONS
FILTER PUMP STATIONARY MOUNTING OPTION

Some countries, especially in the European community, require the filter-pump to

be secured to the ground or to a base in a permanent upright position. Check your
local authorities to determine if there is a regulation in your area regarding
above-the-ground swimming pool filter-pumps. If yes, then the filter-pump can be
mounted to a platform using the two holes located in the base. See drawing below.

The filter-pump can be mounted on a cement base or onto a wooden platform to

prevent accidental falling over. Total assembly must exceed 18kg.

130 mm

1. The mounting holes are 6.4mm in diameter and spaced 130mm apart.
2. Use two bolts and lock nuts with a maximum of 6.4mm in diameter.

SAVE THESE INSTRUCTIONS Page 10

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS

1. Make sure the filter pump is switched off. The switch is located on the motor
housing.
2. Connect the power cord to a GFCI protected electrical outlet.

WARNING
Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or residual
current device (RCD). Contact a qualified electrician if you cannot verify
that the receptacle is protected by a GFCI/RCD. Use a qualified electrician
to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a
portable residual current device (PRCD).

IMPORTANT
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open the
air release valve, wait until water starts to flow out of the air release valve,
close air release valve.

3. Turn both plunger valve handles fully counter-clockwise until they stop. This
opens the valve, allowing water to flow into the filter pump.
4. With water flowing into filter pump, the water pressure will allow the air trapped
inside to escape from the air release valve (2). When all the air has escaped
water will flow out of the valve (2). When this occurs gently finger tighten the
valve (2) in a clockwise direction.
5. To operate the filter pump on “TIMER” mode:
A. Set the timer dial to the desired operating hours. See operation time table.
See Fig. 10
B. Turn on the pump by pressing the switch to “ ” position, the filter pump is
now filtering the water and will stop after the operating hours are
completed. The built-in timer will now operate for the number of hours
selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “-” position, the filter pump is
now filtering the water.
B. To turn off the pump, press the switch to “O” position.

6 8
4
12
2

TIMER DIAL (HOURS)

ON OFF TIMER
FIG 10

SAVE THESE INSTRUCTIONS Page 11

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

OPERATING TIME TABLE

This table shows the required operating time for average use of the filter pump with AGP's.
The filter pump running time should be 1 hour longer than the required operating time of the
Saltwater System.

Water Capacity (Calculated at 90% Recommend

for Frame Pool and 80% for Easy Set operating hours
Pool Size & Oval Pool) per day
(Gals) (Liters) (Hours)
INTEX ABOVE GROUND POOLS (AGP’s)
18’ x 42” (549cm x 107cm) 4,786 18,115 4
EASY SET®
POOL
18’ x 48” (549cm x 122cm) 5,455 20,647 6

CIRCULAR 18’ x 48” (549cm x 122cm) 6,423 24,311 6

METAL FRAME
POOL 21’ x 52” 9,533 36,082 8

16' x 48" (488cm x 122cm) 5,061 19,156 4

18’ x 48” (549cm x 122cm) 6,423 24,311 6

ULTRA FRAME
POOL
18’ x 52” (549cm x 132cm) 6,981 26,423 6

20’ x 48” 7,947 30,079 6

15’8” x 49” 4,440 16,805 4

SEQUOIA SPIRIT® 16'8" x 49" (508cm x 124cm) 5,061 19,156 4

POOL SET
18'8" x 53" (569cm x 135cm) 6,981 26,423 6

OVAL FRAME 20’ x 12’ x 48” (610cm x 366cm x 122cm) 4,393 16,628 4
POOL
15’ x 9’ x 48” 3,484 13,187 4

18’ x 9’ x 52” (549cm x 274cm x 132cm) 4,545 17,203 4

RECT. ULTRA
FRAME POOL
20’ x 10’ x 52” 5,611 21,238 4

24’ x 12’ x 52” (732cm x 366cm x 132cm) 8,403 31,805 6

SAVE THESE INSTRUCTIONS Page 12

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

MAINTENANCE
CLEANING OR REPLACING FILTER CARTRIDGES

It is recommended that the filter cartridge be replaced at least

every 2 weeks.
1. Make sure the filter pump is turned off, then disconnect the power cord from
the electrical outlet.
2. Turn both plunger valve handles fully clockwise until they stop. This closes the
valve, prevents the water from flowing out of the pool.
3. Gently turn the top air release valve once or twice in a counter-clockwise
direction. The housing cover can now be easily removed.
4. In a counter-clockwise direction remove the filter housing collar (1). Place it in
a safe location.
5. Remove the housing cover (4).
6. Now remove the used filter cartridge.
7. Examine the inside of the filter housing.
8. If dirt or sediment is located on the bottom of the housing then:
A. In a counter-clockwise motion gently unscrew and remove the sediment
valve (2) located at the bottom of the housing. Place it in a safe place.
B. With a bucket of water or a garden hose pour water into the housing
flushing out the sediment.
C. Screw back the sediment valve (2) in a gentle clockwise motion. Do not
over-tighten.
9. Place a new cartridge filter in the housing.
10. Return the housing cover (4) to its position and in a clockwise direction rescrew
the housing collar (1) onto the filter housing.
11. Turn both plunger valve handles fully counter-clockwise until they stop. This
opens the valve, allowing water to flow into the filter pump.
12. When the trapped air has escaped through the air release valve gently
retighten the valve (2) in a clockwise direction.
13. Reconnect the power cord.
14. Turn on the pump.

SAVE THESE INSTRUCTIONS Page 13

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

MAINTENANCE
POOL CARE AND CHEMICALS­
• All pools require care to keep the water clear and hygienically clean. With proper
chemical control, your filter will help attain this objective. Consult your pool supply
dealer for instructions regarding the proper use of chlorine,
algaecide and other chemical agents required for sparkling clear water.
• Keep pool chemicals away from children.
• Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations
could occur.
• Daily pH checking and chemical treatment of the water is very important and can not
be overemphasized. Chlorine, algaecide and maintenance of proper pH levels are
required when filling the pool as well as during the season. Consult your local
swimming pool supply store for instructions.
• The season's first filling of the pool may have brackish water requiring extra water
additives and extra filter changes. Do not allow swimming in pool until the pH level
is balanced. Consult your local swimming pool supply store for instructions.
• Keep spare filter cartridges on hand. Replace cartridges every two weeks.
• Chlorinated water may damage lawns, gardens or shrubbery as children play in the
pool and splash water outside the pool. Lawn areas underneath the pool liner will
be destroyed. Note that some types of grass may grow through the liner.
• Filter run time depends on pool size, weather and usage level. Experiment with
various run times so as to produce clean clear water.

CAUTION
Concentrated chlorine solutions may damage the pool liner. Always
follow the chemical manufacturer’s directions, and the health and hazard
warnings.

LONG TERM STORAGE

1. Before emptying your pool for long term storage, or relocation, be sure the water is
directed towards an acceptable drain water receptacle away from the house. Check
local regulations for specific directions regarding disposal of swimming pool water.
2. Disconnect power cord from electrical outlet.
3. Now, drain the pool.
4. When the pool is empty, disconnect all hoses from pump and plunger valves and
remove the strainers from the pool wall.
5. Drain all water from the filter pump.
6. Leave filter pump pieces & hoses outside to thoroughly air dry.
7. Remove both plunger valves from the threaded strainer connector (13). Be careful
not to lose the step rubber washer (10).
8. Coat the following O-rings and washers with petroleum jelly for long term storage:
• Air release valve & sediment O-rings (3).
• Filter housing cover O-ring (5).
• Pump hose O-rings (9).
• Strainer valve assembly step washers (10).
• Flat strainer rubber washers (12).
9. Discard the used filter cartridge. Put aside 1 or 2 new cartridges for next season’s
use.
10. It is best to place all dry pieces in the original packaging for storage or place them
in an airtight plastic bag.
11. Store the unit and accessories in a dry place. The storage's temperature should be
controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and 104 degrees
Fahrenheit (40 degrees Celsius) storage location.

IMPORTANT
It is best to store away your poolsystem in its original packaging.

SAVE THESE INSTRUCTIONS Page 14

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE

TROUBLE CAUSE SOLUTION

FILTER MOTOR • The motor is not plugged in. • Filter cord must be plugged into a 3 wire
FAILS TO START • The Fuse box needs checking. outlet that is protected by a Class A
• The GFCI/RCD circuit breaker Ground Fault Circuit Interrupter, or RCD.
is tripped. • Reset circuit breaker. If circuit breaker
• Motor too hot and overload trips repeatedly, your electrical system
protection is shut off. may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Let the motor cool down.

FILTER DOESN’T • Improper chlorine or pH • Adjust the chlorine and pH level.

CLEAN POOL levels. Consult your local swimming pool
• Filter cartridge is dirty. supply stores.
• Damaged cartridge. • Clean or replace cartridge.
• Excessively dirty pool. • Check the cartridge for holes. Replace
• The strainer screen is if damaged.
restricting the water flow. • Operate the filter for longer periods.
• Clean the strainer screen at the inlet.

FILTER DOESN’T • Clogged inlet or discharge. • Clear any obstructions in the intake hose by
PUMP WATER OR • An air leak on the intake line. discharging it inside pool wall.
THE WATER FLOW • Scale or buildup on cartridge. • Tighten hose nuts, check hoses for
damage, check pool water level.
IS VERY SLOW • Excessively dirty pool. • Replace cartridge.
• Dirty filter cartridge. • Clean cartridge more often.
• The nozzle and strainer • Clean inside the plunger valve.
connection are reversed. • Pull valve handle to full upright position.
• Install the nozzle at the upper position of
the pool inlet, and the strainer at the lower
position of the pool outlet.

PUMP DOESN’T • Low water level. • Fill pool to correct water level.
WORK • Strainer screen plugged up. • Clean strainer screens at pool inlet.
• An air leak on the intake hose. • Tighten hose nuts, check hose for damage.
• Faulty motor or the impeller • Clear any sticks or leaves in the
is jammed. intake hose.
• An air lock inside the cartridge • Turn and pull valve handle to full
chamber. upright position.

TOP COVER • O-ring missing. • Remove cover & check for O-ring.
LEAKING • Cover is not tight. • Tighten cover (Manually).
• Filter cartridge is dirty. • Replace or clean cartridge.

HOSE LEAKING • Hose nuts are not well-fitted. • Tighten or reinstall hose nut.

AIR LOCK • There’s air trapped in the • Open air release valve, wait until water
pump housing and inlet hose. starts to flow out of the valve, then
• The inlet and outlet hoses close it.
connection are reversed. • The lower position of pool outlet
connects to filter pump water inlet. The
upper position of pool inlet connects to
filter pump water outlet.

IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.

SAVE THESE INSTRUCTIONS Page 15

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

COMMON PROBLEMS
COMMON POOL PROBLEMS

PROBLEM DESCRIPTION CAUSE SOLUTION

ALGAE • Greenish water. • Chlorine and pH levels • Super chlorinate with shock
• Green or black need adjustment. treatment. Correct pH to your
spots on pool liner. pool store's recommended
• Pool liner is level.
slippery and/or has • Vacuum pool bottom.
a bad odor. • Maintain proper chlorine
level.

COLORED • Water turns blue, • Copper, iron or • Adjust pH level to the

WATER brown, or black manganese in water recommended level.
when first treated being oxidized by the • Run filter until water is clear.
with chlorine. added chlorine. • Clean cartridge frequently.
This is Common.

FLOATING • Water is cloudy or • "Hard water" caused • Correct the pH level. Check
MATTER IN milky. by a too high pH level. with your pool dealer for
WATER • Chlorine content is low. advice.
• Foreign matter in • Adjust the chlorine level.
water. • Clean or replace your filter.

CHRONIC • Level is lower than • Rip or hole in pool • Repair with a patch kit.
LOW WATER on previous day. liner or hoses. • Finger tighten all caps.
LEVEL • The drain valves are
loose.

SEDIMENT • Dirt or sand on • Heavy use, getting in • Use Intex pool vacuum to
ON POOL pool floor. and out of pool. clean bottom of pool.
BOTTOM

SURFACE • Leaves, insects • Pool too close to • Use Intex pool skimmer.
DEBRIS etc. trees.

SAVE THESE INSTRUCTIONS Page 16

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

SAFETY GUIDELINES
GENERAL AQUATIC SAFETY

Water recreation is both fun and therapeutic. However, it involves

inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.

For additional safeguards, also familiarize yourself with the following

general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instruct all pool users, including children what to do in case of an
emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, supervise, supervise.

SAVE THESE INSTRUCTIONS Page 17

 (108) MODEL 636T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2012

English 108A

LIMITED WARRANTY
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal
Clear™ Filter-Pump and accessories listed below.
The following provision is only valid within the European member states countries: The
legal regulation of Directive 1999/44/EC will not be effected by this Intex warranty.

The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty is
invalid.
Krystal Clear™ Filter-Pump Warranty – 1 Year
Hoses, Plunger Valves & Fittings Warranty – 180 days

If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim.

IMPLIED WARRANTIES ARE LIMITED TO THE TERMS OF THIS WARRANTY AND IN

NO EVENT SHALL INTEX, THEIR AUTHORIZED AGENTS OR EMPLOYEES BE LIABLE
TO THE BUYER OR ANY OTHER PARTY FOR DIRECT OR CONSEQUENTIAL
DAMAGES OR LIABILITIES.

This Limited Warranty does not apply if the products are subject to negligence, abnormal
use or operation, accident, improper operation, improper voltage or current contrary to
operating instructions, or to damage by circumstances beyond Intex’s control, including but
not limited to, ordinary wear and tear and damage caused by exposure to fire, flood,
freezing, rain, or other external environmental forces. This Limited Warranty applies only to
those parts and components sold by Intex. The Limited Warranty does not cover
unauthorized alterations, repairs or disassembly by anyone other than Intex Service
Center personnel.

The Limited Warranty is also not applicable if this product is used with another product
other than an Intex product, when setting up your pool.

The costs associated with the loss of pool water, chemicals or water damage are not
covered by this warranty. Injury or damage to any property or person is not covered by this
warranty.

SAVE THESE INSTRUCTIONS Page 18