Service Manual

1100UE/1100UEL
4×4

ZHEJIANG XINYANG INDUSTRY CO.,LTD.

 FOREWORD
This service manual is designed primarily for use by certified XINYANG Master Service Dealer
technicians in a properly equipped shop and should be kept available for reference. All references to
left and right side of the vehicle are from the operator's perspective when seated in a normal riding
position.
Some procedures outlined in this manual require a sound knowledge of mechanical theory, tool use,
and shop procedures in order to perform the work safely and correctly. Technicians should read the
text and be familiar with service procedures before starting the work. Certain procedures require the
use of special tools. Use only the proper tools as specified.
This manual contains an introductory description of procedures for inspection，maintenance,
overhaul ， disassembly & assembly ， removal and installation of components and parts,
troubleshooting and service data together with illustrations of our vehicle Model XY1100UE and
XY1100UEL.

The manufacturer reserves the right to make improvements or modifications to the products
without prior notice. Overhaul and maintenance should be done according to the actual state
and condition of the vehicle.

CONTENTS
Vehicle
Service Information 1
Vehicle Body, Muffler 2
Checks & Adjustment 3
Cooling System 4
Removal and Installation of Engine 5
Mechanical part of SQR 472Engine 6
Fuel injector system 7
Front Wheel, Front Brake, Suspension, Steering 8
Rear Wheel, Rear Brake, Suspension 9
Front and Rear Axle 10
EFI system of SQR 472engine 11
Lighting and switches 12
Relays and fuses distribution diagram
Circuit Diagram
 1. SERVICE INFORMATION

A few Words About Safety ……………1-1 Main Data Table………………………1-20

Fasteners…………………………………1-3 Tightening Torque………………………1-24
1
Basic tools………………………………1-5 Lubricating oil, and brake liquid………1-25
Description and vehicle identification…1-18
VIN Number Engine Number…………1-19

A Few Words About Safety

Service Information
The service and repair information contained in this manual is intended for use by qualified,
professional technicians.
Attempting service or repairs without the proper training, tools, and equipment could cause injury to
you or others, It could also damage the vehicle or create an unsafe condition.
This manual describes the proper methods and procedures for performing service, maintenance, and
repairs. Some procedures require the use of specially designed tools and dedicated equipment. Any
person who intends to use a replacement part, service procedure or a tool that is not recommended
by XinYang, must determine the risks to their personal safety and the safe operation of the vehicle.
If you need to replace a part, use genuine XinYang parts with the correct part number or an
equivalent part. We strongly recommend that you do not use replacement parts of inferior quality.

For Your Customer is Safety

Proper service and maintenance are essential to the customer is safety and the reliability of the
vehicle. Any error or oversight while servicing a vehicle can result in faulty operation, damage to
the vehicle, or injury to others.

For Your Safety

Because this manual is intended for the professional service technician, we do not provide warnings
about many basic shop safety practices (e.g., Hot parts-wear gloves). If you have not received shop
safety training or do not feel confident about your knowledge of safe servicing practice, we
recommended that you do not attempt to perform the procedures described in this manual.
Some of the most important general service safety precautions are given below. However, we
cannot warn you of every conceivable hazard that can arise in performing service and repair and
procedures. Only you can decide whether or not you should perform a given task, can cause you to
be seriously hurt or killed.

Important Safety Precautions

Make sure you have a clear understanding of all basic shop safety practices and that you are

1-1
 1. SERVICE INFORMATION

wearing appropriate clothing and using safety equipment. When performing any service task, be
especially careful of the following:
● Read all of the instructions before you begin, and make sure you have the tools, the replacement
or repair parts, and the skills required to perform the tasks safely and completely.
● Protect your eyes by using proper safety glasses, goggles or face shields any time you hammer,
drill, grind, pry or work around pressurized air or liquids, and springs or other stored-energy
components. If there is any doubt, put on eye protection.
● Use other protective wear when necessary, for example gloves or safety shoes. Handing hot or
sharp parts can cause severe burns or cuts. Before you grab something that looks like it can hurt
you, stop and put on gloves.
● Protect yourself and others whenever you have the vehicle up in the air. Any time you lift the
vehicle, either with a hoist or a jack, make sure that it is always securely supported. Use jack
stands.
Make sure the engine is off before you begin any servicing procedures, unless the instruction tells
you to do otherwise. This will help eliminate several potential hazards;
● Carbon monoxide poisoning from engine exhaust, Be sure there is adequate ventilation whenever
you run the engine.
● Burns from hot parts or coolant. Let the engine and exhaust system cool before working in those
areas.
● Injury from moving parts. If the instruction tells you to run the engine, be sure your hands, fingers
and clothing are out of the way.
Gasoline vapors and hydrogen gases from batteries are explosive. To reduce the possibility of a fire
or explosion, be careful when working around gasoline or batteries.
● Use only a nonflammable solvent, not gasoline, to clean parts.
● Never drain or store gasoline in an open container.
● Keep all cigarettes, sparks and flames away from the battery and all fuel-related parts.

Conversion Table
Item Example Conversion
2 2
Pressure 200Kpa(2.00kgf/cm ) 1kgf/cm =98.0665kpa
33kpa(250mmHg) 1kpa=1000pa
1mmHg=133.322Pa=0.133322Kps
Torque 18N· m(1.8kgf-m) 1kgf· m=9.80665N· m
3
Volume 419ml 1ml=1 cm =1cc
3
1l=1000cm
Force 12N(1.2kgf) 1kgf=9.80665N

1-2
 1. SERVICE INFORMATION

Cleaning Parts
1
Cleaning parts is one of the more tedious and difficult service jobs performed in the home garage.
Many types of chemical cleaners and solvents are available for shop use. Most are poisonous and
extremely flammable. To prevent chemical exposure, vapor buildup, fire and serious injury, observe
each product warning label and note the following:
1. Read and observe the entire product label before using any chemical. Always know what type of
chemical is being used and whether it is poisonous and/or flammable.
2. Do not use more than one type of cleaning solvent at a time. If mixing chemicals is required,
measure the proper amounts according to the manufacturer.
3. Work in a well-ventilated area.
4. Wear chemical-resistant gloves.
5. Wear safety glasses.
6. Wear a vapor respirator if the instructions call for it.
7. Wash hands and arms thoroughly after cleaning parts.
8. Keep chemical products away from children and pets.
9. Thoroughly clean all oil, grease and cleaner residue from any part that must be heated.
10. Use a nylon brush when cleaning parts. Metal brushes may cause a spark.
11. When using a parts washer, only use the solvent recommended by the manufacturer. Make sure
the parts washer is equipped with a metal lid that will lower in case of fire.

Warning Labels
Most manufacturers attach information and warning labels to the UTV. These labels contain
instructions that are important to personal safety when operating, servicing, transporting and storing
the UTV. Refer to the owner’s manual for the description and location of labels. Order replacement
labels from the manufacturer if they are missing or damaged.

FASTENERS
Proper fastener selection and installation is important to ensure the motorcycle operates as
designed and can be serviced efficiently. The choice of original equipment fasteners is not arrived at
by chance. Make sure replacement fasteners meet all the same requirements as the originals
Many screws. Bolts and studs are combined with nuts to secure particular components. to indicate
the size of a nut. Manufactures specify the internal diameter and the thread pitch
The measurement across two flats on a nut or bolt indicates the wrench size
WARNING

Warning : Do not install fasteners with a strength classification lower than what was originally
installed by the manufacturer doing so may cause equipment failure and or damage

Torque Specifications
The material used in the manufacturing of the UTV may be subjected to uneven stresses if the
fasteners of the various subassemblies are not installed and tightened correctly. Fasteners that are
improperly installed or work loose can cause extensive damage. it is essential to use an accurate
torque wrench as described in this chapter.

1-3
 1. SERVICE INFORMATION

Self-Locking Fasteners
Several types of bolts. Screws and nuts incorporate a system that creates interference between
the two fasteners. Interference is achieved in various ways. The most common types are the nylon
insert nut and a dry adhesive coating on the threads of a blot.
Self-locking fasteners offer greater holding strength than standard fasteners, which improves their
resistance to vibration. All self-locking fasteners cannot be reused. The materials used to from the
lock become distorted after the initial installation and removal. Discard and replace self-locking
fasteners after removing them. Do not replace self-locking fasteners with standard fasteners.

Washers
The two basic types of washers are flat washers and lock washers. Flat washers are simple discs
with a hole to fit a screw or bolt. Lock washers are used to prevent a fastener from working loose.
Washers can be used as spacers and seals. Or can help distribute fastener load and prevent the
fastener from damaging the component
As with fasteners. When replacing washers make sure the replacement washers are of the same
design and quality

Cotter Pins
A cotter pin is a split metal pin inserted into a hole or slot to prevent a fastener from loosening. In
certain applications, such as the rear axle on an UTV or motorcycle, the fastener must be secured in
this way. For these applications. A cotter pin and castellated (slotted) nut is used.
To use a cotter pin, first make sure the diameter is correct for the hole in the fastener. Aster
correctly tightening the fastener and aligning the holes, insert the cotter pin through the hole and
bend the ends over the fastener, Unless instructed to do so, never loosen a tightened fastener to
align the holes. If the holes do not align. Tighten the fastener enough to achieve alignment
Cotter pins are available in various diameters and lengths. Measure the length from the bottom of
the head to the tip of the shortest pin.

Snap Rings and E-clips

Snap rings (Figure 1) are circular-shaped metal
retaining clips. They secure parts in place on parts
such as shafts. External type snap rings are used to
retain items on shafts. Internal type snap rings secure
parts within housing bores. In some applications. in
addition to securing the component(s). snap rings of
varying thicknesses also determine endplay. These
are usually called selective snap rings.
The two basic types of snap rings are machined
and stamped snap rings. Machined snap rings (Figure
2) can be installed in either direction. Because both
faces have sharp edges. Stamped snap rings (Figure
3) are manufactured with a sharp and a round edge.
When installing a stamped snap ring in a thrust

1-4
 1. SERVICE INFORMATION

application, install the sharp edge facing away from

the part producing the thrust. 1
E-clips are used when it is not practical to use a
snap ring. Remove E-clips with a flat blade
screwdriver by prying between the shaft and E-clip. To
install an E-clip. Center it over the shaft groove and
push or tap it into place
Observe the following when installing snap rings:
1. Remove and install snap rings with snap rings
pliers. Refer to Basic Tools in this chapter
2. In some applications. it may be necessary to
replace snap rings after removing them
3. Compress or expand snap rings only enough to
install them. If overly expanded. Lose their
retaining ability
4. After installing a snap ring. Make sure it seats completely
5. Wear eye protection when removing and installing snap rings

BASIC TOOLS
Most of the procedures in this manual can be carried out with basic hand tools and test equipment
familiar to the home mechanic. Always use the correct tools for the job. Keep tools organized and
clean. Store them in a tool chest with related tools organized together.
Quality tools are essential. The best are constructed of high-strength alloy steel. These tools are
light, easy to use and resistant to wear. Their working surface is devoid of sharp edges and carefully
polished. They have an easy-to-clean finish and are comfortable to use. Quality tools are a good
investment.
Some of the procedures in this manual specify special tools. In many cases the tools is illustrated
in use. Those with a large tool kit may be able to replacement. However, in some cases, the
specialized equipment or expertise may make it impractical for the home mechanic to attempt the
procedure. When necessary, such operations are recommended to have a dealership or specialist
perform the task. It may be less expensive to have a professional perform these jobs, especially
when considering the cost of equipment.
When purchasing tools to perform the procedures covered in this manual, consider the tool’s
potential frequency of use. If a tool kit is just now being started. Consider purchasing a basic tool
set from a quality tool combinations and offer substantial savings when complicated, specialized
tools can be added.

Screwdrivers
Screwdrivers of various lengths and types are mandatory for the simplest tool kit. The two basic
types are the slotted tip (flat blade) and the Phillips tip. These are available in sets that often include an
assortment of tip size and shaft lengths.
As with all tools, use a screwdriver designed for the job. Make sure the size of the fastener. Use
them only for driving screws. Never use a screwdriver for
prying or chiseling metal. Repair or replace worn or

1-5
 1. SERVICE INFORMATION

damaged screwdrivers. A worn tip may damage the

fastener, making it difficult to remove.
Phillips-head screws are often damaged by
incorrectly fitting screwdrivers. Quality Phillips
screwdrivers are manufactured with their crosshead tip
machined to Phillips Screw Company specifications.
Poor quality or damaged Phillips screwdrivers can back
out (cam out) and round over the screw head. In addition.
Weak or soft screw materials can make removal difficult.
The best type of screwdriver to use on Phillips
screw is the ACR Phillips II screwdriver, patented by the
horizontal anti-cam out ribs found on the driving faces or
flutes of the screwdriver’s tip (figure 4). ACR Phillips II
screwdrivers were designed as part of a manufacturing
drive system to be used with ACR Phillips II screws, but
they work of tool companies offer ACR Phillips II
screwdrivers in different Tip size and interchangeable
bits to fit screwdriver bit holders.
NOTE:
Another way to prevent cam out and to increase
the grip of a Phillips screwdriver is to apply valve
grinding compound or permute screw ＆ socket
Gripper onto the screwdriver tip. After loosening/
tightening the screw, clean the screw recess to
prevent engine oil contamination.

Wrenches
Open-end, box-end and combination wrenches
(figure 5) are available in a variety of types and sizes.
The number stamped on the wrench refers to the distance
of the fastener head.
The box-end wrench is an excellent tool because it grips
the fastener on all sides. This reduces the chance of the
tool slipping. The box-end wrench is designed with either
a 6 or 12-point opening. For stubborn or damaged fasteners,
the 6-point provides superior holding because it contacts the
fastener across a wider area at all six edges. For general use,
the 12-point works well. It allows the wrench to be removed
and reinstalled without moving the handle over such a wide
are.
An open-end wrench is fast and works best in
areas with limited overhead access. It contacts the
fastener at only two points and is subject to slipping if
under heavy force, or if the tool or fastener is worn. A

1-6
 1. SERVICE INFORMATION

box-end wrench is preferred in most instances,

especially when braking loose and applying the final 1
tightness to a fastener.
The combination wrench has a box-end on one
end and an open-end on one end and an open-end on
the other. This combination makes it a convenient tool.

Adjustable wrenches
An adjustable wrench or Crescent wrench (Figure
6) can fit nearly any nut or bolt head that has clear
access around its entire perimeter. An adjustable
wrench is best used as a backup wrench to keep a
large nut or bolt from turning while the other end is
being loosened or tightened with a box-end or socket
wrench.
Adjustable wrenches contact the fastener at only
two points, which makes them more subject to slipping
off the fastener. Because one jaw is adjustable and
may become loose, this shortcoming is aggravated.
Make certain the solid jaw is the one transmitting the
force.

Socket Wrenches, Ratchets and

Handles
Sockets that attach to a ratchet handle (Figure 7)
are available with 6-point or 12-point openings
(Figure8) and different drive sizes. The drive size
Indicates the size of the square hole that accepts the
Ratchet handle. The number stamped on the socket
is the size of the work area and must the fastener head
As with wrenches. a 6-point provides superior-holding
ability. While a 12-point socket needs to be moved only
half as for to reposition it on the fastener
Sockets are designated for either hand or impact use.
Impact sockets are made of thicker material for more durability. Compare the size and wall
thickness of a 19-mmhand socket (A, Figure 9) and the 19-mm impact socket (B). Use impact
sockets when using an impact driver or air tools. Use hand sockets with hand-driven attachments
WARNING:
Do not use hand sockets with air or impact tools
because they may shatter and cause injury.
Always wear eye protection when using impact
or air tools

1-7
 1. SERVICE INFORMATION

Various handles are available for sockets. Use the

speed handle for fast operation. Flexible ratchet heads in
varying length allow the socket to be turned with varying
force and at odd angles. Extension bars allow the socket
setup to reach difficult areas. The ratchet is the most
versatile. It allows the user to install or remove the nut
without removing the socket.
Sockets combined with any number of drivers make them
undoubtedly the fastest. Safest and most convenient tool
for fastener removal and installation

Impact Drivers
An impact driver provides extra force for removing fasteners by converting the impact of a
hammer into a turning motion. This makes it possible to remove stubborn fasteners without
damaging them. Impact drivers and interchangeable bits (Figure 10) are available from most tool
suppliers.When using a socket with an impact driver. Make sure the socket is designed for impact
use. Refer to Socket Wrenches. Ratchets and handles in this section.
WARNING:
Do not use hand sockets with air or impact tools
because they may shatter and cause injury.
Always wear eye protection when using impact
or air tools

Allen Wrenches
Use Allen or setscrew wrenches (Figure 11) on
fasteners with hexagonal recesses in the fastener
head. These wrenches are available in L-shaped bar.
Socket and T-handle types. A metric set is required
when working on most motorcycles. Allen bolts are
sometimes called socket bolts.

Torque Wrenches
Use a torque wrench with a socket, torque
adapter or similar extension to tighten a fastener to a
measured torque. Torque wrenches come in several
drive sizes (1/4, 3/8, 1/2 and 3/4) and have various
methods of reading the torque value. The drive size
indicates the size of the square drive that accepts the
socket, adapter or extension. Common methods of
reading the torque value are the deflecting beam, the
dial indicator and the audible click (Figure 12).
When choosing a torque wrench, consider the
torque range, drive size and accuracy. The torque specifications in this manual provide an indication
of the range required.

1-8
 1. SERVICE INFORMATION

A torque wrench is a precision tool that must be properly cared for to remain accurate. Store
torque wrenches in cases or separate padded drawers within a toolbox. Follow the manufacturer’s 1
instructions for their care and calibration.

Torque Adapters
Torque adapters or
extensions extend or reduce the
reach of a torque wrench. The
torque adapter shown in (Figure
13) is used to tighten a fastener
that cannot be reached because
of the size of the torque wrench
head, drive, and socket. If a
torque adapter changes the
effective lever length (Figure 14),
the torque reading on the wrench
will not equal the actual torque
applied to the fastener. It is
necessary to recalibrate the
torque setting on the wrench to
compensate for the change of
lever length. When using a torque
adapter at a right angle to the
drive head, calibration is not
required, because the effective
length has not changed.
To recalculate a torque
reading when using a torque adapter, use the following formula and refer to Figure 14:
TW = TA×L
L+A
TW is the torque setting or dial reading on the wrench.
TA is the torque specification and the actual amount of torque that is applied to the fastener.
A is the amount that the adapter increases (or in some cases reduces) the effective lever length as
measured along the centerline of the torque wrench.
L is the lever length of the wrench as measured from the center of the drive to the center of the grip.
The effective length is the sum of L and A.
Example:
TA=20 ft.-lb.
A=3in.
L=14in.
TW=20×14=280=16.5 ft. - lb.
14+3 = 17
In this example, the torque wrench would be set
to the recalculated torque value (TW = 16.5 ft. –lb.).

1-9
 1. SERVICE INFORMATION

When using a beam-type wrench, tighten the fastener

until the pointer aligns with 16.5 ft. –lb. In this example,
although the torque wrench is pre set to 16.5 ft. –lb.,
the actual torque is 20 ft. –lb.

Pliers
Pliers come in a wide range of types and sizes.
Pliers are useful for holding, cutting, bending, and
crimping. Do not use them to turn fasteners. Figure 15
and Figure 16 show several types of useful pliers.
Each design has a specialized function. Slip-joint
pliers are general – purpose pliers used for gripping
and bending. Diagonal cutting pliers are needed to cut
wire and can be used to remove cotter pins. Use
needle nose pliers to hold or bend small objects.
Locking pliers (Figure 16), sometimes called Vise-
Grips, are used to hold objects very tightly. They have
many uses ranging from holding two parts together, to
gripping the end of a broken stud. Use caution when
using locking pliers, as the sharp jaws will damage the
objects they hold.

Snap Ring Pliers

Snap ring pliers are specialized pliers with tips that
fit into the ends of snap rings to remove and install them.
Snap ring pliers (Figure 17) are available with a fixed action (either internal or external ) or
convertible (one tool works on both internal and external snap rings). They may have fixed tips or
interchangeable ones of various sizes and angles. For general use, select a convertible type pliers
with interchangeable tips (Figure 17).
WARNING:
Snap rings can slip and fly off when removing and
installing them. Also, the snap ring pliers tips may break.
Always wear eye protection when using snap ring pliers.

Hammers
Various types of hammers are available to fit a number of applications. Use a ball-peen hammer to
strike another tool, such as a punch or chisel. Use soft-faced hammers when a metal object must be
struck without damaging it. Never use a metal-faced hammer on engine and suspension components
because damage occurs in most cases.
Always wear eye protection when using hammers. Make sure the hammer face is in good
condition and the handle is not cracked. Select the correct hammer for the job and make sure to
strike the object squarely. Do not use the handle or the side of the hammer to strike an object.

1-10
 1. SERVICE INFORMATION

Ignition Grounding Tool

1
Some test procedures require turning the engine
over without starting it. To prevent damage to the
ignition system from excessive resistance or the
possibility of fuel vapor being ignited by an open spark,
remove the spark plug cap and ground it directly to a
good engine ground with the tool shown in (Figure
18).
Make the tool shown from a No.6 screw and nut,
two washers, length of tubing, alligator clip, electrical eyelet and a length of wire.

PRECISION MEASURING TOOLS

The ability to accurately measure components is essential to perform many of the procedures
described in this manual. Equipment is manufactured to close tolerances, and obtaining consistently
accurate measurements is essential to determine which components require replacement or further
service.
Each type of measuring instrument is designed to measure a dimension with a certain degree of
accuracy and within a certain range. When selecting the measuring tool, make sure it is applicable
to
the task.
As with all tools, measuring tools provide the best results if cared for properly. Improper use can
damage the tool and cause inaccurate results. If any measurement is questionable, verify the
measurement using another tool. A standard gauge is usually provided with micrometers to check
accuracy and calibrate the tool if necessary.
Precision measurements can vary according to the experience of the person performing the
procedure. Accurate results are only possible if the mechanic possesses a feel for using the tool.
Heavy-handed use of measuring tools produces less accurate results. Hold the tool gently by the
fingertips to easily feel the point at which the tool contacts the object. This feel for the equipment
produces more accurate measurements and reduces the risk of damaging the tool or component.
Refer to the following sections for specific measuring tools.

Feeler Gauge
Use feeler or thickness gauges (Figure19) for
measuring the distance between two surfaces.
A feeler gauge set consists of an assortment of
steel strips of graduated thickness. Each blade is
marked with its thickness. Blades can be of various
lengths and angles for different procedures.
A common use for a feeler gauge is to measure
valve clearance. Use wire (round) type gauges to
measure spark plug gap.

1-11
 1. SERVICE INFORMATION

Calipers
Calipers (Figure 20) are excellent tools for
obtaining inside, outside and depth measurements.
Although not as precise as a micrometer, they allow
reasonable precision, typically to within 0.05 mm
(0.001 in.). Most calipers have a range up to 150 mm
(6 in.).
Calipers are available in dial, venire or digital versions. Dial calipers have a dial readout that
provides convenient reading. Venire calipers have marked scales that must be compared to
determine
the measurement. The digital caliper uses a liquid-crystal display (LCD) to show the measurement.
Properly maintain the measuring surfaces of the caliper. There must not be any dirt or burrs
between the tool and the object being measured. Never force the caliper to close around an object.
Close the caliper around the highest point so it can be removed with a slight drag. Some calipers
require calibration. Always refer to the manufacturer’s instructions when using a new or unfamiliar
caliper.
To read a vernire. Calipers refer to Figure 21. The
fixed scale is marked in l-mm increments. Ten
individual lines on the fixed scale equal 1 cm. The
movable scale is marked in 0.05 mm (hundredth)
increments. To obtain a reading, establish the first
number by the location of the 0 line on the movable
scale in relation to the first line to the left on the fixed
scale. In this example, the number is 10 mm. To
determine the next number, note which of the lines on
the movable scale align with a mark on the fixed scale.
A number of lines will seem close, but only one will align exactly. In this case, 0.50 mm is the
reading to
add to the first number. Adding 10 mm and 0.50 mm equals a measurement of 10.50 mm.

Micrometers
A micrometer is an instrument designed for linear measurement using the decimal divisions of
the inch or meter (Figure 22). While there are many types and styles of micrometers, most of the

1-12
 1. SERVICE INFORMATION

procedures in this manual call for an outside

micrometer. Use the outside micrometer to measure
the outside diameter of cylindrical forms and the
thickness of materials.
A micrometer’s size indicates the minimum and
maximum size of a part that it can measure. The usual
sizes (Figure 23) are 0-25mm (0-1 in.), 25-50 mm (1-2
in.), 50-75 mm (2-3 in.) and 75-100 mm (3-4 in.).
Micrometers that cover a wider range of
measurements are available. These use a large frame
with interchangeable anvils of various lengths. This type of micrometer offers a cost savings, but its
overall size may make it less convenient.
When reading a micrometer, numbers are taken from different scales and added together. The
following sections describe how to adjust, care for and read the measurements of various types of
outside micrometers.
For accurate results, properly maintain the measuring surfaces of the micrometer. There cannot
be any dirt or burrs between the tool and the measured object. Never force the micrometer to close
around an object. Close the micrometer around the highest point so it can be removed with a slight
drag.

Adjustment
Before using a micrometer, check its adjustment as follows:
1. Clean the anvil and spindle faces.
2A. To check a 0-1 in. or 0-25 mm micrometer:
a. Turn the thimble until the spindle contacts the anvil. If the micrometer has a ratchet stop, use it to
ensure that the proper amount of pressure is applied.
b. If the adjustment is correct, the 0 mark on the thimble will align exactly with the 0 mark on the
sleeve line. If the marks do not align, the micrometer is out of adjustment.

1-13
 1. SERVICE INFORMATION

c. Follow the manufacturer’s instructions to adjust the micrometer.

2B. To check a micrometer larger than 1 in. or 25 mm use the standard gauge supplied by the
manufacturer. A standard gauge is a steel block, disc or rod that is machined to an exact size.
a. Place the standard gauge between the spindle and anvil, and measure its outside diameter or
length. If the micrometer has a ratchet stop, use it to ensure that the proper amount of pressure is
applied.
b. If the adjustment is correct, the 0 mark on the thimble will align exactly with the 0 mark on the
sleeve line. If the marks do not align, the micrometer is out of adjustment.
c. Follow the manufacturer’s instructions to adjust the micrometer.

Care
Micrometers are precision instruments. They must
be used and maintained with great care. Note the
following:
1. Store micrometers in protective cases or separate
padded drawers in a tool box.
2. When in storage, make sure the spindle and anvil
faces do not contact each other or another object. If
they do, temperature changes and corrosion may
damage the contact faces.
3. Do not clean a micrometer with compressed air. Dirt
forced into the tool will cause wear.
4. Lubricate micrometers with WD-40 to prevent
corrosion.

Metric micrometer
The standard metric micrometer (Figure 24) is
accurate to one one-hundredth of a millimeter (0.01
mm). The sleeve line is graduated in millimeter and
half millimeter increments. The marks on the upper
half of the sleeve line equal 1.00 mm. Each fifth mark
above the sleeve line is identified with a number. The
number sequence depends on the size of the
micrometer. A 0-25 mm micrometer, for example, will
have sleeve marks numbered 0 through 25 in 5 mm
increments. This numbering sequence continues with
larger micrometers. On all metric micrometers, each
mark on the lower half of the sleeve equals 0.50mm.
The tapered end of the thimble has 50 lines marked
around it. Each mark equals 0.01 mm. One completer
turn of the thimble aligns its 0 mark with the first line
lower half of the sleeve line or 0.50mm.
When reading a metric micrometer, add the number of millimeters and half-millimeters on the
sleeve line to the number of one one-hundredth millimeters on the thimble. Perform the following

1-14
 1. SERVICE INFORMATION

steps
while referring to Figure 25. 1
1. Read the upper half of the sleeve line and count
the number of lines visible. Each upper line equals
1mm.
2. See if the half –millimeter line is visible on the
lower sleeve line. If so, add 0.50mm to the reading
in Step 1.
3. Read the thimble mark that aligns with the sleeve
line. Each thimble mark equals 0.01mm.
NOTE:
If a thimble mark does not align exactly
with the sleeve line. Estimate the amount between the lines.
For accurate readings in two-thousandths of a millimeter
(0.002mm), use a metric vernier micrometer.
4. Add the readings from Steps 1-3.

Standard inch micrometer

The standard inch micrometer (Figure 26) is
accurate to one-thousandth of an inch or 0.001. The
sleeve is marked in 0.025 in. increments. Every fourth
sleeve mark is numbered 1,2,3,4,5,6,7,8,9. These
numbers indicate 0.100, 0.200, 0.300, and so on.
The tapered end of the thimble has 25 lines
marked around it. Each mark equals 0.001 in. One
complete turn of the thimble will align its zero mark
with the first mark on the sleeve or 0.025 in.
To read a standard inch micrometer, perform the
following steps and refer to Figure 27.
1. Read the sleeve and find the largest number
visible. Each sleeve number equals 0.100 in.
2. Count the number of lines between the numbered
sleeve mark and the edge of the thimble. Each
sleeve mark equals 0.025 in.
3. Read the thimble mark that aligns with the sleeve
line. Each thimble mark equals 0.01 in.

NOTE:
If a thimble mark does not align exactly with the sleeve line, estimate the
amount between the lines. For accurate readings in ten-thousandths of an
inch (0.0001 in), use a vernier inch micrometer.
4. Add the readings from Steps 1-3.

1-15
 1. SERVICE INFORMATION

Telescoping and Small Bore Gauges

Use telescoping gauges (Figure 28) and small
bore gauges (Figure 29) to measure bores. Neither
gauge has a scale for direct readings. Use an outside
micrometer to determine the reading.
To use a telescoping gauge, select the correct
size gauge for the bore. Compress the movable post
and. Care fully insert the gauge into the bore. Carefully
move the gauge in the bore to make sure it is centered.
Tighten the knurled end of the gauge to hold the
movable post in position. Remove the gauge and
measure the length of the posts. Telescoping gauges
are typically used to measure cylinder bores.
To use a small bore gauge, select the correct size
gauge for the bore. Carefully insert the gauge into the
bore. Tighten the knurled end of the gauge to carefully
expand the gauge fingers to the limit within the bore.
Do not over tighten the gauge because there is no
built-in release. Excessive tightening can damage the
bore surface and damage the tool. Remove the gauge
and measure the outside dimension (Figure 30).
Small bore gauges are typically used to measure
valve guides.

Dial Indicator:
A dial indicator (Figure 31) is a gauge with a dial
face and needle used to measure variations in
dimensions and movements. Measuring brake rotor
runout is a typical use for a dial indicator.
Dial indicators are available in various ranges and
graduations and with three basic types of mounting
bases: magnetic (B. Figure 31). Clamp, or screw-in
stud. When purchasing a dial indicator, select on with
a continuous dial (A, Figure 31).
Cylinder Bore Gauge
A cylinder bore gauge is similar to a dial indicator.
The gauge set shown in Figure 32 consists of a dial
indicator, handle, and different length adapters (anvils)
to fit the gauge to various bore sizes. The bore gauge is
used to measure bore size, taper and out-of-round. When
using a bore gauge, follow the manufacturer’s instructions.

1-16
 1. SERVICE INFORMATION

Compression Gauge
1
A compression gauge (Figure 33) measures combustion chamber (cylinder) pressure, usually in
PSI or kg/ cm2 . The gauge adapter is either inserted or screwed into the spark plug hole to obtain
the
reading. Disable the engine so it does not start and
hold the throttle in the wide-open position when
performing a compression test An engine that does
not have adequate compression cannot be properly
tuned. Refer to Chapter Three.

Multimeter
A multimeter (Figure 34) is an essential tool for
electrical system diagnosis. The voltage function
indicates the voltage applied or available to various electrical components. The ohmmeter function
tests circuits for continuity, or lack of continuity, and measures the resistance of a circuit.
Some manufacturer’s specifications for electrical components are based on results using a specific
test meter. Results may vary if using a meter not recommended by the manufacturer. Such
requirements are noted when applicable.
Ohmmeter (analog) calibration
Each time an analog ohmmeter is used or if the scale is changed, the ohmmeter must be
calibrated.
Digital ohmmeters do not require calibration.
1. Make sure the meter battery is in good condition.
2. Make sure the meter probes are in good condition.
3. Touch the two probes together and observe the needle location on the ohms scale. The needle
must Align with the 0 mark to obtain accurate measurements.
4. If necessary, rotate the meter ohms adjust knob until the needle and 0 mark align.

1-17
 1. SERVICE INFORMATION

Description and vehicle identification

1. Meter adjust button 2. Driver model turn switch 3. Turning switch

4. Light switch 5. Low beams/High beams turn 6. Horn switch
7. Gear Selector 8. Ignition Switch 9. Meter
10. Warning indicator light switch 11. Wiper switch(optional)
12. Spot light(optional) 13. Cigarette lighter 14. winch switch(optional)
15. Auxiliary DC jack(12V 120W/10A)

1-18
 1. SERVICE INFORMATION

Identification number records

Record the vehicle identification number and engine number in the spaces provided for assistance
when ordering spare parts from your dealer or for reference in case the vehicle is stolen.
1

Vehicle Identification Number(1100UE): LCXRSAS3~

Vehicle Identification Number(1100UEL): LCXLSAS3~
Engine Number: SQR472F

NOTE: The vehicle identification number is used to identify your

machine.

1-19
 1. SERVICE INFORMATION

Main Data Table

Item Parameter
Model 1100UE/1100UEL
Length 2830mm/3630mm
Width 1640mm/1640 mm
Height 2130mm/2130mm
Wheel base 1830mm/2630mm
Engine type SQR472F
Displacement 1083ml
Fuel type Unleaded gasoline 93octane or above
Mass of whole equipments (Not include driver) 711kg/800 kg
Number of Passengers 2 for 1100UE, 4 for 1100UEL(including driver)
Max. Load 300Kg
Tire Front 26x9-14
Rear 26x11-14
Minimum turning radius 4500mm/5000mm
Start-up mode Electric starter
Type in-line Vertical, four-cylinder, water-cooled,
DOHC
Combustion Chamber Type Tent-shaped
Bore × stroke 72×66.5 mm (2.83×2.62 in)
Compression ratio 9.5:1
Lubrication Type Compound (pressure, splash lubrication)
Cool type Mandatory cycle of antifreeze-coolant
Maximal power. 50Kw/6000 rpm(EEC model less than
15kw)
Max. torque 90N.M/3500~4000 rpm(EEC
model:45N.M/2240 rpm)
Lowest fuel consuming rate (g/Kw·h) ≤ 275g/Kw·h
Idling speed (r/min) 850±50 r/min
Engine
Starting Performance The engine should be started smoothly in 30S
without any special measure when the air
temperature is -25℃.Start test is allowed to start
three times continuously as a row. It can be
restarted in 2 minutes later after the first failure.
The direction of camshaft rotary motion clockwise（From the front-end look at the
engine crankshaft pulley）
Spark plug K6RTG
Generators 14V75A whole-alternator
Lubricating oil category API SF SAE 10W/30
Engine oil pump type Rotor Style
Oil filter type As a whole mounted rotating
Fuel supply EFI

1-20
 1. SERVICE INFORMATION

Item Parameter
Fuel type 93 unleaded gasoline high cleanliness
1
Transmission V-belt with teeth on, auto stepless gear
change, plus gear change cam with change
gear transmission
Gear change type gear lever with hand
Clutch type wet, hoof centrifugal type
Primary speed change ratio(stepless speed 0.84—3.28
change)
Engine/ Speed change ratio： Total speed reduce ratio
Gearing H Gear：2.66 2.23—8.72
L Gear： 5.527 4.64—18.13
R Gear： 6.80 5.71—22.30
Cooling style Closed cooling fluid circulating
Cooling fluid type antifreeze with prevent rust
Out dimension 555.8 x 455.9 x 699
Net weight 80kg
Output type front and rear shaft output
Shaft running direction counter-clockwise (from back of engine).
Steering Steering Right 40°
device angle Left 40°
Brake type Front Hydraulic Disc
Rear Hydraulic Disc
Bumper
Suspension Swing Arm
Device
Frame type Welded steel tube and plate

Overhaul Datasheet
Lubricating device
Item Standard Service limit
Oil pump Gap between inner 0.05~0.18mm 0.35mm
Rotor and outer rotors
Gap between rotor and 0.10～0.181mm 0.25mm
body
Engine Oil Volume when replacing 3500ml —
Capacity Full capacity 3600ml —

1-21
 1. SERVICE INFORMATION

Recommended Oil (see original) ● Specially for 4-stroke

motorcycle
SAE-10W-40、20W-50
Substitutes must be used in
the following range.

●API type: SE or SF grade

●SAE type: Choose from
the left chart according to
the environmental
temperature
Cooling Device
Item Standard
Full Capacity 4500ml
Coolant capacity Reservoir tank capacity 3300 ml
Standard Density 50%
Opening pressure of radiator cap 108kpa(1.1kgf/cm2)
Thermostat Temperature / valve open 72±2 ºC
Temperature/valve full open 88 ºC
Overall lift 3.5-4.5mm/95ºC
Front/Rear Wheel
Item Standard Service Limit
Play of wheel Vertical 1.0mm 2.0mm
rim
Front Horizontal 1.0mm 2.0mm
Wheel Tire Groove — 3.0mm
Pressure 12PSI(83KPa) ±0.5PSI(±3.5KPa)
Play of wheel Vertical 1.0mm 2.0mm
rim
Horizontal 1.0mm 2.0mm
Rear
Wheel Tire Groove — 3.0mm
Pressure 12PSI(83KPa) ±0.5PSI(±3.5KPa)

Brake System
Item Standard Service Limit
Front brake Brake Pedal Play 0mm --
Brake disc thickness 4mm 3mm
Brake Pedal Play 0mm --
Rear brake
Brake disc thickness 4mm 3mm

1-22
 1. SERVICE INFORMATION

Battery、Charging System
Item Standard 1
AC magneto Model Permanent magnet AC type
Motor Output 3- phase AC
Charging coil Resistance (20℃) 0.2-0.3Ω
Rectifier Three-phase annular rectification, Silicon controlled
parallel-connected regulated voltage
Battery Capacity 12V36Ah
Terminal point Fully charged 12.8V
voltage Insufficient <11.8V
charge
Charging Standard 0.9A/5~10H
current/time
Quick 4A/1H

Ignition system
Item Standard
Ignition ECU ignition
Spark Plug Type K6RTG (NGK)

Optional ---
Spark plug gap 0.9-1.1mm

1-23
 1. SERVICE INFORMATION

Screwing moment of important bolts

FRONT, REAR SUSPENSION：
THREAD TORQUE REMARK
S.Q. ITEM QTY.
DIAMETER （N·m）
FRONT/REAR SHOCK
1 M10×1.25×50 8 30~40
ABSORBER
2 FRONT BRAKE DISK M10×25 8 40~50
3 REAR BRAKE DISK M10×25 8 40~50
RUBBER WASHER OF
4 M10×1.25 8 40~50
ENGINE
5 ENGINE SUPPORT A M10×25 4 40~50
6 ENGINE SUPPORT B M10×1.25 2 40~50
7 CVT DRIVER M12×175 1 40~50
CVT SECONDARY
8 M10×115 1 40~50
SHEAVE
FRONT LOWER/ UPPER
9 M10×1.25×90 8 40~50
ARM
10 JOINT,ARM BALL M10×1.25 2 40~50
REAR LOWER/ UPPER
11 M10×1.25×90 8 40~50
ARM
12 FRONT/REAR AXLE NUT M18 4 180~200
13 STEERING WHEEL M5×15 6 10
14 STEERING SHAFT M8×25 4 20~30
15 FRONT AXLE M10×1.25×145 1 40~50
16 FRONT AXLE M10×1.25×85 1 40~50
HOLDER,FRONT
17 M8×16 6 20~30
AXLE(FR/RR)
18 REAR AXLE M12×1.25×115 2 40~50
HOLDER,REAR
19 M8×16 6 20~30
AXLE(FR/RR)
20 FRONT DRIVE SHAFT M8×25 4 20~30
REAR DRIVE SHAFT/
21 M8×30 4 20~30
PARKING DISC
COUPLING FLANGE,
22 M14×1.25 1 90~100
REAR DRIVE SHAFT
SUPPORT,PARKING
23 M8×45 3 20~30
CALIPER
HOLDER，BRAKE AND
24 M10×1.25×25 4 40~50
THROTTLE
FRONT/REAR BRAKE
25 M10×1.25 8 40~50
CALIPER

1-24
 1. SERVICE INFORMATION

26 HANDLE BRAKE M8 3 20~30 1

27 NUT , WHEEL M12×1.25 16 40~50

Specification Tightening moment

M6 10N·m
Other screws （ 8.8
M8 25N·m
grade）
M10 50N·m
M12 80N·m

Specification and usage quantity for fuel

Lubricating oil and brake liquid

Category Specification Capacity Remark
Fuel RQ-93or upper grade 35L
lead-free gasoline
Lubricating oil（engine, SAE15W—40/SF or 3600ml(change oil)
Gear box） SC 3500ml(change filter)
Front :500ml
Gearbox
Rear :1300ml
Lubricating oil （ front Change 0.25L
main driver） SAE80W—90/GL-4
Lubricating oil ( Rear Change 0.18L
main driver）
Brake liquid GB1083 JG3 0.5L
Engine coolant Distilled water: Extremely cold area，
Glycol =1:1 Distilled water:
Glycol =2:3

1-25
 2. Vehicle body，Muffler
Overhaul info……………………………2-1 Front cover assy……………………………2-11
Troubleshooting…………………………2-1 Cargo box…………………………………2-13
Steering wheel & platfond ………………2-2 Muffler……………………………………2-16
Windshield assembly………………………2-3
Side door…………………………………2-4
Triangular cover & rear board……………2-5
Seat belt & main protect pole assy…………2-6
Front bumper………………………………2-9
Front line cover & front air guide cover assy…2-10

Overhaul Information

Operation Cautions

Warning
Gasoline is highly flammable, therefore smoke and fire are strictly forbidden in the work
place. Special attention should also be paid to sparks. Gasoline may also be explosive
when it is vaporized, so operation should be done in a well-ventilated place.
Remove and Install muffler after it is fully cold.
● This chapter is on the disassembly and installation of rack, visible parts, exhaust pipe,
Muffler and fuel tank.
● Hoses, cables and wiring should be routed properly
● Replace the gasket with a new one after muffler is removed
● After muffler is installed, check if there is any exhaust leakage.
Tightening torque
Muffler Exhaust Pipe Nut: 40-50N.m

Troubleshooting
Loud exhaust noise
● Broken muffler
● Exhaust leakage
Insufficient power
● Distorted muffler
● Exhaust leakage
● Muffler clogged

2-1
 2. Vehicle body，Muffler

Cover, steering wheel

2
Remove
Exert upward to separate cover, steering
Wheel.

Installation
Reverse the removal procedure for
Installation

Steering wheel
Remove
Remove six bolts 1
Remove steering wheel

Installation

Note
Align the front wheel first, and then
adjust steering wheel;

Reverse the removal procedure for

Installation

Platfond
Remove

Remove four bolts 2

Remove platfond

Installation
Reverse the removal procedure for
Installation

2-2
 2. Vehicle body，Muffler

Windshield Assembly

Remove
Separate the connector of wiper motor.

Remove four bolts 1.

Remove windshield assembly.

Installation
Reverse the removal procedure for
Installation

1. WIPER BLADE
2. WIPER ARM
3. BOLT(M6×20）
4. WINDSHIELD SCALEBOARD
5. BOLT(M6×16）
6. FARDAGE WINDSHIELD
7. CAP NUT (M6)
8. HOOP (Φ45)
9. WINDSHIELD IMMOBILITY
PLANK（TOP）
10. WINDSHIELD IMMOBILITY
PLANK（BELOW）
11. NUT，FLANGE(M6)
12. WIPER
13. DUST COVER, RUBBER
14. NUT (M12)
15. WASHER (Φ12)
16. RUBBER WASHER
17. WIPER ASSY

2-3
 2. Vehicle body，Muffler

Side door (LF)

2
Remove
Remove bolt 1
Remove side door (LF)
Remove the side door of the another side in
the above way.

Installation
Reverse the removal procedure for
Installation.

1100UEL：Side door (LR)

Remove
Remove bolt 2
Remove side door (LR)
Remove the side door of the another side in
the above way.

Installation
Reverse the removal procedure for
installation

15. TAPPING SCREW (ST 4.2×20)

16. SCREW (M6×25)
17. HANDLE, HALF DOOR (L)
18. SCREW (M5×20)
19. INNER HALF DOOR (L)
20. INNER HALF DOOR (R)
21. WASHER (Φ5×Φ10×1)
22. BOLT FLANGE (M6)
23. BOLT FLANGE (M6×16)
24. BOLT FLANGE (M5)
25. CABLE, HALF DOOR
26. HANDLE, HALF DOOR(R)
27. OUTER HALF DOOR (L)
28. OUTER HALF DOOR (R)

2-4
 2. Vehicle body，Muffler

Triangular Cover

Remove
Remove bolt 1
Remove triangular cover
Remove the triangular cover of the another side in
the above way.

Installation
Reverse the removal procedure for installation.

Rear Left Board

Remove
Remove bolt 2
Remove bolt 3
Remove rear left board.
Remove the rear right board in the above way.

Installation
Reverse the removal procedure for Installation.

2-5
 2. Vehicle body，Muffler

Seat belt
2
Remove
Remove bolt 3
Remove bolt 4
Remove driver seat belt.
Remove the passenger seat belt in the above way.
Remove rear seat belt of passenger in same method.

Installation
Reverse the removal procedure for Installation.
Install rear seat belt of passenger in same method.

Main Protect Pole ASSY

Remove
Remove bolt 1
Remove bolt 2
Remove the main protect pole assy of the another
side in the above way.
Remove main protect pole assy.
Installation
Reverse the removal procedure for Installation.

2-6
 2. Vehicle body，Muffler

XY1100UE:

1. FRONT PROTECT POLE ASSY (L) 2. HOOP (Ф45)

3. BOLT，FLANGE（M8×16） 4. REAR THWARTWISE PIPE
5. FRONT BENT PIPE 6. CAP NUT (M8)
7. BACKREST PIPE 8. HEADREST
9. SCREW (M5×20) 10. BACKREST
11. RUBBER，STORE BOX 12. CAP NUT(M6)
13. CENTER SPACER, HOOP 14. PLATFOND
15. BOLT，FLANGE（M6×55） 16. WASHER(Ф6×Ф12×2)
17. BOLT (M10×30) 18. LOCK CATCH, SAFETY BELT
19. SAFETY BELT ASSY 20. FRONT PROTECT POLE ASSY(R)

2-7
 2. Vehicle body，Muffler

XY1100UEL:
2
1.FRONT PROTECT POLE ASSY(L)

2. HOOP(φ45)

3. BOLT，FLANGE（M8×16）

4. REAR THWARTWISE PIPE

5. FRONT BENT PIPE

6. CAP NUT(M8)

7. BACKREST PIPE

8. HEADREST

9. SCREW(M5×20)

10. BACKREST

11. RUBBER，STORE BOX

12. CAP NUT(M6)

13. CENTER SPACER, HOOP

14. CEILING

15. BOLT，FLANGE（M6×55）

16. WASHER (φ6×φ12×2)

17. BOLT(M10×30)

18. LOCK CATCH, SAFETY BELT

19. SAFETY BELT ASSY

20. FRONT PROTECT POLE ASSY(R)

21. REAR PROTECT POLE ASSY(L)

22. REAE PROTECT POLE ASSY(R)

23. BACKREST

2-8
 2. Vehicle body，Muffler

Front Bumper

Remove
Remove bolt 1
Remove front cover cable.
Remove bolt 2
Remove front bumper
Installation

Reverse the removal procedure for

Installation.

1. COBBRA，BUMPER 2. FRONT BUMPER

3. DECORATE COVER, FRONT BUMPER 4. SCREW（M6×20）
5. BOLT,FLANGE（M6×20) 6. BOLT,FLANGE（M8×16)
7. CABLE,FRONT COVER 8. LOCKNUT，FLANGE (M10×1.25)
9. CABLE PULLEY 10. LOCKNUT，FLANGE(M8)
11. WINCH HOLDER 12. WINCH
13. BOLT,FLANGE（M10×1.25×70)

2-9
 2. Vehicle body，Muffler

COVER, LEFT LINE.FR (L)

2
Remove
Remove bolt 1
Remove the front left line cover(L)
Remove the front right line cover(R) in same method.

Installation
Reverse the removal procedure for Installation.

FRONT AIR GUIDE COVER ASSY

Remove
Separate the connector of headlight.
Remove the eight bolts 2.
Remove the front air guide cover assy.

Installation
Reverse the removal procedure for Installation.

2-10
 2. Vehicle body，Muffler

FRONT COVER ASSY

Remove
Remove the front air guide cover assy.(2-10)
Remove the steering wheel assy.(2-2)
Remove the gear change handle.
Remove the two bolts 1.
Remove the nine bolts 2.
Loosen all electronic component and plugs.
Remove the front cover assy.

Installation
Reverse the removal procedure
for Installation.

2-11
 2. Vehicle body，Muffler

1. HEADLIGHT (L) 2. TAPPING SCREW(ST5.2×20)

3. WASHER (φ5×φ10×1) 4. HEADLIGHT(R)
5. FRONT AIR GUIDE COVER ASSY 6. SCREW(M6×20)
7. NUT(M6) 8. BOARDING，VENT GRILLE(FRONT)
9. FRONT MUDGUARDR(R) 10. EXPANSION SCREW (M8×20)
11. FRONT MUDGUARDR (L) 12. ENGINE COVER BOARD
13. TAPPING SCREW (ST4.2×20) 14. ENGINE COVER BOARD DECORATE COVER
15. SCREW (M6×20) 16. RUBBER WASHER(φ6)
17. GEMEL 18. NUT,CLIP（M6）
19. DECORATE COVER, FRONT COVER 20. FRONT COVER
21. COVER, LEFT LINE.FR (L) 22. COVER, RIGHT LINE.FR (R)
23. SCALEBOARD, METER PANEL 24. SEPTI-BOARD, STORE BOX
25. METER PANEL 26. AIRPROOF COVER, GEARSHIFT
27. AIRPROOF COVER, PARKING HANDLE 28. TEACUP COVER
29. COVER BOARD, STORE BOX 30. PIN
31. SUPPORT, PIN

2-12
 2. Vehicle body，Muffler

Cargo box

Remove

Remove the connectors of taillights

Remove the “R” pin (Ф4)
Remove the pin of cargo box.

Use the same method to remove the

“R” pin and cargo box pin on the other
side of the cargo box.

Figure direction pulling tipping rocker of

cargo box.

Remove “R” pin of gas spring.

Remove connection of gas spring and cargo.

Remove cargo box.

Installation
Reverse the removal procedure for
Installation.

2-13
 2. Vehicle body，Muffler

1. DECORATING COVER，CARGO BOX 2. TAPPING SCREW(ST5.2×20)

3. EXPANSION SCREW(M8×20) 4. LEFTWARD COVER，CARGO BOX
5. FENDER，CARGO BOX（L） 6. FENDER，CARGO BOX（R）
7. TIPPING ROCKER 8. ROCKER COVER, TIPPING
9. POTHOOK SEAT 10. TORSION SPRING (BIG)
11. BOLT,FLANGE（M8×45） 12. LOCKNUT，FLANGE(M8)
13. HEAT INSULATION BOARD 14. RIVET (5×20)
15. CARGO BOX FRAMRE 16. DECORATING COVER, CARGO BOX
17. HALF DOOR FRAMRE 18. BOLT,FLANGE（M8×12）
19. ROTATE PIN PIPE 20. BOARD，CARGO BOX DOOR
21. REAR CORNER COVER,CARGO BOX (R) 22. HANDLE，CARGO BOX DOOR
23. LOCKNUT，FLANGE(M6) 24. REAR HEIGHTEN WASHER(R)
25. TIE ROD, HALF DOOR 26. LOCK, GARGO BOX (L)
27. BOLT,FLANGE（M8×20） 28. PIN

2-14
 2. Vehicle body，Muffler

29. NUT，FLANGE(M8) 30. CABLE,CARGO BOX

31. LOCK, GARGO BOX(R) 32. DOOR BOARD，CARGO BOX
33. REAR REFLECTOR 34. TAILLIGHT
35. TAILLIGHT SEAT 36. NUT，FLANGE(M5)
37. REAR CORNER COVER,CARGO BOX (L) 38. REAR HEIGHTEN WASHER (L)
39. SCREW（M6×30） 40. RUBBER WASHER(Φ6)
41. STARBOARD COVER，CARGO BOX 42. BUCKLE，PLATE
43. BOLT,FLANGE（M8×20) 44. CARGO BOX HANDLE RUBBER WASHER（R）
45. PROTECT COTE TUBE 46. FRONT HEIGHTEN WASHER (L)
47. SCREW（M6×20） 48. NUT,CLIP（M6）
49. FRONT HEIGHTEN WASHER(R) 50. CARGO BOX HANDLE RUBBER WASHER（L）
51. PIN, CARGO BOX 52. “R” PIN(Ф4)
53. “R” PIN(Ф3) 54. GAS SRPING, CARGO BOX
55. CIRCLIP(Ф8) 56. LOCK, GARGO BOX ASSY

2-15
 2. Vehicle body，Muffler

Muffler
2
Caution: Perform disassembly only
after the muffler is cooled down.

Remove
Remove two flange bolts (M10×30)
Remove tension spring of exhaust pipe.
Remove catalytic converter assy.
Remove exhaust pipe and muffler.
Note:
Replace seal ring when installing
the muffler.

Installation
Reverse the removal procedure for installation

MUFFLER ASSY

1. SEAL RING 2. BOLT，FLANGE(M10×30）

3. LOCKNUT，FLANGE(M10) 4. EXHAUST PIPE

5. RUBBER WASHER A 6. TENSION SPRING, EXHAUST PIPE
7. CATALYTIC CONVERTER 8. RUBBER WASHER B
9. MUFFLER

2-16
 3. CHECKS & ADJUSTMENT

Overhaul Info………………………………………………………………………………3-1
Regular maintenance Table………………………………………………………………3-2
Inspection & Maintenance…………………………………………………………………3-3
Shift Linkage Inspection / Adjustment……………………………………………………3-6
Steering Stem………………………………………………………………………………3-8
Wheels………………………………………………………………………………………3-10
Suspension System…………………………………………………………………………3-12
Gear Shifting, Fuel Device…………………………………………………………………3-13
Throttle Pedal check…………………………………………………………………………3-14
Cooling System………………………………………………………………………………3-15

Overhaul Info
Operation Cautions
Note
● DO NOT keep the engine running for long time in a poorly ventilated or enclosed place because
of the harmful components like CO, etc, in the exhaust gas.
● The muffler and engine are still very hot when the engine is just stopped. Careless contact may
cause serious burn. Be sure to wear fatigue dress with long sleeves and gloves if the work has to
be done after the engine is just stopped
● Gasoline is highly flammable, smoking is strictly forbidden in the work place. Keep alert on the
electrical sparks. Besides, vaporized gasoline is highly explosive, so work should be done in a
well-ventilated place.
● Be careful that your hands or clothes not get nipped by the turning or movable parts of the driving
system.

Note
The vehicle should be parked on hard and level ground.

Replace parts regularly

Parts replacement time is subject to time or kilometers, whichever occurs first.

3-1
 3. CHECKS & ADJUSTMENT

Regular Maintenance Table

The table below lists the recommended intervals for all the required periodic maintenance work 3
necessary to keep the vehicle at its best performance and economy. Maintenance intervals are
expressed in terms of kilometer, miles and hours, whichever occurs first.
Note: More frequent maintenance may be required on vehicles that are used in severe conditions.
Interval Km Initial Every Every Remarks
250km 500 km 1000 km
Item Hours Initial 20 Every 50 Every 100
hours hours hours
Valve clearance I — I IN： 0.18±0.05
EX： 0.25±0.05
Idle Speed I I — 850 r/min±50r/min

Spark plug I — I No carbon deposit,

R( Every :6000km ) Gap：0.9~1.1mm

Air Filter — I C R(every :20000km)

Fuel Hose, carburetor — — I
Clutch — — I R(every: 4-year)
Drive Belt — I —
Oil Filter R — R
Oil change R — R
Coolant Level I I —
Water Hose & Pipes I — I
Coolant R( every: 2-year)
I－Check and adjust, or replace if necessary
R－Replace
C－Clean

3-2
 3. CHECKS & ADJUSTMENT

Inspection & Maintenance ○：Interval

Check Item Interval Standard
Part Item Daily 1/2 Year Annual
Steering Steering Operation agility ○ ○
System wheel
Steering Damage ○ ○
System Installation ○ ○
condition of
steering system
Sway of ball stud ○ ○
Brake Brake pedal Free play ○ ○ ○ Pedal: rear end 0mm
System Brake Efficiency ○ ○ ○
Connecting Looseness, ○ ○
rod, oil pipe Slack and damage
& Hose
Hydraulic Front and rear ○ ○ ○ Brake fluid should be above
brake and brake fluid level LOWER limit
brake disc Brake disc ○ ○ ○ Replace when the thickness of
damage and wear front brake disc is less than
3mm, rear brake less than
3mm
Driving wheel Tire pressure ○ ○ ○ Front tire ：83kPa
System (12±1PSI)
Rear tire ：83kPa
(12±1PSI)
Chap and damage ○ ○ No wear indication on the
surface of tire (the remained
depth of groove should not be
less than 3mm)
Groove depth and ○ ○
abnormal wear
Loosened wheel ○ ○ ○
nut and axle
Sway of front ○ ○
wheel bearing
Sway of rear ○ ○
wheel bearing
Buffer Suspension Sway of joint ○ ○
System arm parts, rocker arm
damage
Shock Oil leakage and ○ ○
absorber damage
Function ○
Drive-Tr Front axle Transmission, ○ ○
ain lubrication`
system Rear axle Transmission, ○ ○
lubrication
Gear box Transmission, ○ ○
lubrication

3-3
 3. CHECKS & ADJUSTMENT

Check Item
Part Item
Intervals
Daily 1/2 year Annual
Standard
3
Drive Train Final shaft Looseness of ○ ○ ○
(Drive joint parts
shaft) Sway of ○
Spline
Electrical Ignition Spark plug ○ ○
System Device Ignition ○ ○
timing
Battery Terminal Joint ○
Wiring Looseness ○
and damage
of joints
Engine Fuel device Fuel leakage ○ ○
Throttle ○
Cooling Coolant level ○ ○ ○
system Coolant ○
leakage

3-4
 3. CHECKS & ADJUSTMENT

Check Item Intervals Standard

Part Item Daily 1/2 year Annual
Lighting device Function ○ ○ ○
and turning
indicators
Alarm and lock Function ○
device

Instruments Function ○

Exhaust pipe Looseness or damage caused ○

and muffler by improper installation
Function of muffler ○

Frame Looseness and/or damage ○

Others Lubrication & grease of frame ○

parts
Abnormal parts Make sure if there is any ○
which can be abnormal with relative parts.
determined
when driving

3-5
 3. CHECKS & ADJUSTMENT

Shift Linkage Inspection / Adjustment

3
Linkage rod adjustment is necessary when symptoms include:
• No All Wheel Drive light
• Noise on deceleration
• Inability to engage a gear
• Excessive gear clash (noise)
• Shift selectors moving out of desired range

NOTE: Remove necessary components to gain

access to shift linkage cable ends.

1. Inspect shift linkage cable, clevis pins, and pivot bushings

and replace if worn or damaged.
2. Be sure idle speed is adjusted properly.
3. Place gear selector in neutral. Make sure the transmission
bell crank is engaged in the neutral position detents.
4. With two wrenches loosen the outside jam nut
counterclockwise. Turn the outside jam nut 1 1/2 turns.
Perform this procedure on the shift lever end, also.
5. After turning the outside jam nut 1 1/2 turns. Hold the
outside jam nut with a wrench and tighten the inside jam
nut clockwise, until it is tight against the bracket.
6. Repeat Step 4 and Step 5 until the proper adjustment is
made for the transmission cable.
7. Use this procedure to loosen or tighten the shift linkage
cable as needed.

Fuel system and air intake

Fuel Lines
1. Check fuel lines for signs of wear, deterioration, damage
or leakage. Replace if necessary.
2. Be sure fuel lines are routed properly and secured with
cable ties. CAUTION: Make sure lines are not kinked or
pinched.
3. Replace all fuel lines every two years.

3-6
 3. CHECKS & ADJUSTMENT

Air Filter Service

It is recommended that the air filter be replaced annually.
When riding in extremely dusty conditions replacement
will be required more often.
The filter should be inspected periodically before each
ride, using the following procedure.
The air box is located rearward of the engine.
1. Remove clips from air box cover and remove cover.
Inspect the gasket. It should adhere tightly to the cover and
seal all the way around.
2. Remove air pre-filter assembly. Do not clean the main
filter, the filter should be replaced.
3. Inspect main element and replace if necessary. If the filter
has been soaked with fuel or oil it must be replaced.
Installation
1. Reinstall the filter into the air box container. Be sure the
filter fits tightly in the air box.
NOTE: Apply a small amount of general purpose
grease to the sealing edges of the filter before
installing. 1.JOINT,AIR CLEANER 2. CIRCLIP
2. Check air box. If oil or water deposits are found, drain them 3. PRIMARY COVER 4. FILTER ELEMENT
into a suitable container. 5. TAIL COVER
NOTE: Service more frequently if vehicle is operated
in wet conditions or at high throttle openings for
extended periods.
3. Install air box cover and secure with clips.

3-7
 3. CHECKS & ADJUSTMENT

Steering Stem
Park the vehicle on level place, hold steering wheel,
3
and shake in the direction as illustrated on the right
and see if there is any sway

In case of any sway, check if it is the problem of the

steering stem or other parts and then do the
maintenance accordingly.

In case of sway of the steering stem, tighten the

locknut or disassemble the steering stem for
further check.

Park the vehicle on level place, slowly turn the

steering wheel left and right to see if it can turn
freely.

In case there is any hindrance, check if there is

any interference. If no, check the steering tie-rod
end, and check if the steering stem bearing is
damaged

Note:
Make sure the steering can be operated freely.
An accident may occur if the steering wheel is out of control.

3-8
 3. CHECKS & ADJUSTMENT

BRAKE SYSTEM
Master Cylinder
Fluid level Check the brake fluid level When the brake
fluid level is near to the minimum(Minimum=1/4H) limit
line, check master cylinder, brake hoses and joints for
leakage.
Remove fluid reservoir cap.
add DOT3 or DOT4 brake liquid till the maximum
(Maximum=H) limit line.
Do not mix with dust or water when adding
brake fluid.
Use only the recommended of brake fluid to avoid
chemical reaction.
Brake fluid may cause damages to the
surface of the plastic and rubber parts.
Keep the fluid away from these parts.
Slightly turn the steering wheel left and right till the
master cylinder is in horizontal, then remove the fluid
reservoir cap.

Brake Disc, Brake Pad

< Wear of brake pad>
Check the brake pad wears from the mark as indicated.
Replace the brake pad if the wear has reached position
of wear limit trough.

Note
The brake pad must be replaced with a whole set.
Checking and replacing the brake disc
Front brake disc thickness: ≤3 mm →Replace
Rear brake disc: ≤3mm →Replace
Min. limited thickness of the front brake disc:3mm
Min. limited thickness of the rear brake disc:3mm
Change The Brake Fluid
< Changing Brake Fluid>
Change the brake fluid once every year.

3-9
 3. CHECKS & ADJUSTMENT

Wheels
3
Lift front wheel on level place, and make sure
there is no loading on the wheels.
Shake the front wheel left and right to check
whether the joint of front wheel is tightened and
check whether it sways.

Not tighten enough ? Tighten it sway: Replace

the rocker arm

Front Toe-in size

Park the vehicle on level place, measure the front
toe-in
Toe-in: B-A=0～10mm

Toe-in out of the range , Adjust the locknut

of tie-rod

Note:
After the toe-in has been adjusted, slowly run the
vehicle to check whether the direction of vehicle
can be controlled by steering wheel.

3-10
 3. CHECKS & ADJUSTMENT

Tire pressure
Check the pressure of the tires with a pressure
gauge.

Note
Check the tire pressure after tires are cooled.
Driving under improper tire pressure will reduce
the comfort of operation and riding, and may
cause deflected wear of the tires.

Specified pressure /tire

Front wheel Rear wheel

Pressure 96.5±3.5kPa (14±0.5PSI) 96.5±3.5kPa (14±0.5PSI)

Tires sizes 27×9-14 27×11-14

OPTIONAL：
Front wheel Rear wheel
Pressure 82.5±3.5kPa (12±0.5PSI) 82.5±3.5kPa (12±0.5PSI)

Tires sizes 26×9-14 26×11-14

Tire Tread
Check the tire tread.

Tread Height: if < 3mm, then Replace with new tires

Note:
When the tread height is less than 3mm,
the tire should be replaced immediately.

3-11
 3. CHECKS & ADJUSTMENT

Wheel Nut and Wheel Axle

3
Check front and rear wheel axle nuts for looseness
Loosened axle nuts
Tighten
Tightening Torque:
Front wheel axle nut:
180-200N.m (18.3kgf.m-20.3kgf.m)
Rear wheel axle nut:
180-200N.m (18.3kgf.m-20.3kgf.m)

Sway of Wheel Bearing

Lift the front wheel
Make sure there is loading on the vehicle shake
the wheel in axial direction for any sway In case
of any sway, disassemble the front wheel and check
the bearing

Suspension System
Park the vehicle on lever place, press the vehicle
Several times up and down as illustrated on the right.

In case of any rocking or abnormal noise, check

whether there is any oil leakage from absorbers, or
any damage or looseness of tightening parts.

3-12
 3. CHECKS & ADJUSTMENT

Adjusting the Absorber

Use special tools to adjust the length of absorber
according to loading requirement Turn clockwise
to adjust from high to low.

Gear Shifting
Shift the gear to check for flexibility and gear
engagement Adjust the gearshift rod if necessary
Release the lock nut to adjust the length of gearshift
rod

Fuel Device

Status of the fuel system

Remove the seat
Check the fuel hose for any aging or damage. Aged or
damaged fuel hose: Replace Check if there is cracks
or bending with the fuel hose. Cracked or bended
fuel hose: Replace

3-13
 3. CHECKS & ADJUSTMENT

Throttle Pedal Check

3

Check the free play of throttle pedal

Free play: 1.5-3mm

If out of range, then adjust

Loosen locknut of throttle cable turn the
regulator and adjust free play of throttle pedal

After adjusting, tighten locknuts and install

throttle cable sleeve.

Replace with a new throttle cable if the specified

free play could not be acquired by adjusting the
regulator or if there is still stickiness with the throttle.

3-14
 3. CHECKS & ADJUSTMENT

Cooling System
Note
● Check coolant level from reservoir tank.
Do not check from radiator.

If the radiator cap is opened while the engine is hot (over 100
℃), the pressure of the cooling system will drop down and the
coolant will get boiled rapidly.

DO NOT open the radiator cap until the coolant temperature

drops down.
●Coolant is poisonous, DO NOT drink or splash it to skin, eyes,
and clothes.
—In case the coolant gets to the skin and clothes, wash with
soap immediately.
—In case the coolant gets into eyes, rinse with plenty of water
and go to consult the doctor
—In case of swallowing the coolant, induce vomit and consult
the doctor.
●Keep the coolant in a safe place and away from reach of
children.

Coolant level
Coolant might reduce due to natural evaporation.
Check the coolant level regularly.

Note
●Coolant can prevent rust and resist freeze.
Ordinary water may cause engine rust or
cracks in winter due to freezing.
●Park the vehicle on level ground for checking
of the coolant. Inclined vehicle body will cause
incorrect judging of the coolant level.
●Check the coolant after the engine is warmed up.
Start and warm up engine.

Stop the engine.

Check if the coolant level is between the upper
and lower limit.

3-15
 3. CHECKS & ADJUSTMENT

When the coolant level is below the LOWER limit,

remove reservoir tank cap and add coolant till upper limit.
(Add coolant or diluted original liquid).
3
Recommended coolant: XYPOWER coolant
Standard density: 50%
( Freezing temperature of coolant varies
according to the different mixture ratio.
Adjust the mixture ratio according to the
lowest temperature in the place where the
vehicle is used.)
If the coolant reduces very fast, check if there
is any leakage. The cooling system may be mixed
with air when there is no coolant in the reservoir
tank and the air should be discharged before
adding coolant.
Coolant Leakage
Check radiator hose, water pump, water pipes
and joints for leakage.
In case of any leakage, disassemble and do
further check. (Refer to Chapter 4)

Check the radiator hose for aging, damages or cracks.

The rubber hose will naturally get aged after a period of service
time. The aged hose may get cracked when the cooling system
is heated. Nip the hose with fingers and check if there are any
tiny cracks.

In case of any abnormal, replace with a new hose.

Check the clamps of the coolant pipes and hose.

Tighten properly in case of any looseness.

Check radiator fins for mud and dust clog or damage.

Correct the bent fins; clean the mud with water and
Compressed air. When the damaged area of the
radiator fin is over 20%, replace with a new
radiator.

Check Water Temperature Gauge

When engine is not working, the water temperature should be in
the “0” position. Start the engine to check if the indicator works. If
the indicator is not working, do the maintenance in time.

3-16
 4. COOLING SYSTEM

Overhauling Info…………………………4-1 Adding Coolant………………………4-5

Trouble Shooting…………………………4-2 Cooling System Chart…………………4-6
Check and Maintenance…………………4-3 Cooling System Assembly Disassembly
Reservoir Tank……………………. ……4-5 /Installation……………………………4-7

Overhaul Information
Note
● If the radiator cap is opened when the coolant temperature is above 100℃, the pressure of
coolant will drop and get boiled rapidly. The steam jet may cause danger and injury. Cover
the cap with a piece of rag after the coolant temperature goes down and open the cap slowly.
● Inspection of coolant should be done after the coolant is fully cooled.
● Coolant is toxic. Do not drink or splash it to skin, eyes or cloth.
—If coolant splashes in your eyes, thoroughly wash your eyes with water and consult a doctor.
—If coolant splashes on your clothes, quickly wash it away with water and then with soap and
water.
—If coolant is swallowed, induce vomit immediately and see a physician.
—Store the coolant properly and keep it away from reach of children.

● Check radiator fins for mud block and/or damage. Correct the bent fins. Clean off the mud
With water and compressed air. Replace with a new one if the damaged fin area reached 20%.

● The overhauling of the water pump can be done without removing the engine.
● Add coolant through reservoir tank. Do not open the radiator cap except when disassembling the
cooling system for adding or drainage of coolant.
● Do not stain the plastic parts with coolant. In case of any coolant stains, flush with water immediately
After disassembly of the cooling system, check the joints for leakage with a radiator cap tester
(available in the market)
● Refer to Chapter 10 for overhauling of temperature transducer.
Inspection standard
Item Standard
Full capacity 4500ml
Coolant
Reservoir tank capacity 3300ml
Capacity Standard density 50%
2
Opening pressure of radiator cap 108kpa(1.1kgf/cm )
Valve open temperature 72±2℃
Thermostat Full open Temperature 88℃
Full open lift 3.5-4.5mm

4-1
 4. COOLING SYSTEM

Trouble Shooting
Sharp rise of water temperature 4
● Faulty radiator cap
● Air in cooling system
● Faulty water pump
● Faulty thermostat (thermostat is not open)
● Clogged radiator pipe or cooling pipes
● Damage or clogged radiator fin
● Coolant is not enough
● Faulty or malfunction of fan motor

No rise or slow rise of water temperature.

Faulty thermostat (thermostat is not closed)

Faulty circuit of water temperature display

Coolant leakage

● Faulty water seal

● O-rings are aged, damaged or improperly sealed.
● Washers are aged, damaged or improperly sealed.
● Improper installation of pipes or hoses
● Pipes and/or hoses are aged, damaged or improperly sealed

4-2
 4. COOLING SYSTEM

Check and Maintenance

Checking coolant density

Note:
Open the radiator cap after coolant is fully cooled.

Open the front cover.

The diagram in the direction of the arrow pulling cable.
Open the front cover.
Remove radiator cap (counter clockwise).
Check with a densimeter if the coolant density
adapts to the local temperature.
Check coolant for stains or impurities.

Inspection of radiator cap

Note
Open the radiator cap after the coolant is fully cooled.
Remove:
Remove bolt 1 and battery panel
Remove radiator cap (counter clockwise)..

Note
Apply coolant on the sealing surface of radiator cap
before attaching the tester to the radiator cap.

Install the radiator cap tester to the radiator cap;

Apply the specified pressure (radiator cap opening

pressure) for 6 seconds and make sure that there is drop in
pressure.

Opening pressure of radiator cap:

2
108~137kpa(1.1~1.4kgf/cm )

4-3
 4. COOLING SYSTEM

Pressure testing of cooling system

Install the radiator cap tester to the radiator cap;
4
Apply the specified pressure (radiator cap opening
pressure) for 6 seconds and make sure that there is drop in
pressure.
Note
Do not apply pressure over the specified pressure
2
[108~137kpa(1.1~1.4kgf/cm )], or the cooling system
may be damaged.
In case there is any pressure leakage, check the pipe, joint
parts, joints of water pump and drainage (→4-5).

Replacing Coolant, Air Discharge

Preparation of coolant
Coolant is toxic, DO NOT drink or splash it to skin,
eyes, and clothes.
—If coolant splashes in your eyes, thoroughly wash
your eyes with water and consult a doctor.
—If coolant splashes on your clothes, quickly wash it
away with water and then with soap and water.
—If coolant is swallowed, induce vomit immediately
and see a physician.
—Store the coolant properly and keep it away from
reach of children.

Note
Mix the coolant (undiluted) with soft water according
to the temperature 5℃ lower than the actual lowest
local temperature.

Coolant should be made from undiluted coolant with soft

water.
Standard density of coolant: 30%
Recommended coolant: XYPOWER coolant
(Direct application without having to be diluted)
Drainage of coolant
Remove radiator cap cover
Note
Open the radiator cap after the coolant is fully cooled.
Remove:
Open the front cover (→4-3)
Remove Radiator cap. (→4-3)

4-4
 4. COOLING SYSTEM

Reservoir Tank
Remove:

Remove front cover assembly (→2-11)

Remove 2 bolts
Remove water hose of reservoir tank

Remove reservoir tank; discharge coolant;

Flush reservoir tank
Install reservoir tank;

Adding Coolant

Add coolant through filling port.

Start the engine and discharge air from cooling system

Check from filling port that air is fully discharged from
cooling system and install the radiator cap

Remove reservoir tank cap and add coolant

till the full limit.

Note:
Check coolant level when the vehicle is
on an even ground.

Air Discharge
Discharge the air from cooling system according to the
following steps:
1. Start the engine and run it several minutes at idle
speed
2. Quickly increase throttle 3~4 times to discharge air
from cooling system;
3. Add coolant till filling port;
4. Repeat step 2 & 3 till no more coolant can be refilled;
5. Check coolant level in reservoir tank and refill till upper
limit.
6. Install reservoir tank cap.

4-5
 4. COOLING SYSTEM

Cooling System Chart

4

4-6
 4. COOLING SYSTEM

COOLING SYSTEM ASSEMBLY DISASSEMBLY/INSTALLATION

1. RADIATOR 2. FAN ASSY 3. RADIATOR RESERVE

4. WATER HOSE 1(φ6×φ10×450) 5. CLAMP（φ10） 6. BUFFERING COLLAR

7. BUMPERBLOCK,RADIATOR 8. CLAMP（25-38） 9. INLET PIPE,ENGINE (FRONT)

10. TIE-IN INTAKE PIPE 11. INLET PIPE,ENGINE (MIDDLE) 12. INLET PIPE,ENGINE (REAR)

13. T-JOINT, WATER PIPE 14. CLAMP（13-19） 15. CYCLE PIPE (REAR)

16. OUTLET PIPE,ENGINE (FRONT) 17. OUTLET PIPE,ENGINE (RAER)

18. BOLT,FLANGE（M6×16） 19. CYCLE PIPE (FRONT)

20. EXHAUST VALVE 21. CYCLE PIPE (FRONT)

22. BOLT(M6×20） 23. SPACER BUSH 24. WATER HOSE 2(φ6×φ10×200)

4-7
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Inspection Information……………5-1 Removal and Installation of Front and Rear

Engine Removal and Installation…5-2 axle……………………………………5-7 5
Removal and Installation of Gearshift…5-7

Inspection Information

Note:
● When removal Engine, please use jack to support the bodywork. Don’t damnify the
frame, body of Engine, bolt and cable etc.
● Please blind up the frame when removal the engine.
● Don’t removal engine from the bodywork when operating as follows:

—THROTTLE VALVE BODY, AIR FILTER.

—CVT SYSTEM, CVT COVER.
—FAN COVER，ENGINE.
—IGNITION COIL
—CAMSHAFT POSITION SENSOR、CRANKCASE POSITION SENSOR
● Following operation require removal of engine from vehicle:
—CRANKCASE

Tightening torque:
RUBBER WASHER OF ENGINE（M10×1.25）：40～50N.m
ENGINE SUPPORT A（M10×25）：40～50N·m
ENGINE SUPPORT B（M10×1.25）:40～50N·m

5-1
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Disassembly Engine
Remove cargo box.
Remove seat.
Remove plastic covers.
Remove air filter.
Remove exhaust pipe and muffler
Remove hoop.
Remove water inlet hose of engine

Remove bolt 1
Remove gear shift rod A.

Remove hoop.
Remove water outlet hose of engine.

Remove nut.
Remove the throttle cable,
Remove hoop
Remove circulating water hose

5-2
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Remove all the connector of engine.

Remove the connector of ECU.

Remove tension spring of exhaust pipe.

Remove catalytic converter.
Remove muffler.

5-3
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Remove the connector of oxygen sensor.

Remove two nuts.

Remove exhaust pipe.

Remove hoop of air filter.

Remove two bolts.

Remove air filter.

Remove hoop of air inlet duct for CVT.

Remove bolt.

Remove air inlet duct of CVT.

5-4
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Remove hoop of air outlet duct for CVT. 5

Remove bolt.

Remove air outlet duct of CVT.

Remove the CVT disassembly/installation.

15. CVT SECONDARY SHEAVE
29. FLANGE PLATE, CVT SUPPORT
37. CVT SECONDARY SHEAVE
38. ORIENTATION COVER,
SECONDARY SHEAVE
39. WASHER（φ12×φ30×2)
40. SPRING WASHER（φ10）
41. BOLT (M10×115)
42. CVT DRIVER
43. CVT BELT
44. CVT IMPELLER
45. SPACER BUSH, DRIVER
46. WASHER（φ12.5×φ30×3)
47. SPRING WASHER（φ12）
48. BOLT (M12×175)
49. SEAL, CVT COVER (LONG)
50. SEAL, CVT COVER (SHORT)
51. BOLT (M6×12)
52. CRANKSHAFT SENSOR
53. CVT COVER (LEFT)
54. JOINT, AIR INLET DUCT
55. BOLT (M6×15)
56. WASHER（φ6×φ12×1.6)
57. CVT PIN
58. BOLT (M6×25)
59. CVT COVER (RIGHT)
60. CIRCLIP (80-100)
61. RUBBER PIPE (φ85×φ92×60)
62. CVT HOSE, IMPORT WIND
63. EXPANSION SCREW(M8×20)
64. RUBBER PIPE (φ85×φ92×60)
65. BOLT(M6×20）
66. CVT HOSE, EXPORT WIND

Remove fixing nuts of engine.

Remove other fixing nuts of engine as shown below.

5-5
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Engine and gearbox disassembly/installation

1. ENGINE
2. FAN
3. BOLT，FLANGE（M6×16）
4. FAN COVER
5. BOLT，FLANGE（M8×16）
6. BOLT，FLANGE（M8×160）
7. SPACER BUSH
8. ENGINE SUPPORT A
9. SPRING WASHER（φ10）
10. INNER-HEX BOLT (M10×25)
11. LOCKNUT，FLANGE
(M10×1.25)
12. RUBBER WASHER OF
ENGING
13. CLAMP（φ10）
14. FUEL HOSEΦ6×Φ10.5×400
15. GEAR-BOX
16. COBBRA, ENGINE HOSE
17. STOPPER, ENGINE HOSE
18. CIRCLIP (16-25)
19. BOLT (M12×1.25×45)
20. LOCKNUT，FLANGE(M10×1.25)
21. BOLT，FLANGE( M12×1.25×35）
22. ENGINE SUPPORT B
23. ENVELOP BOARD, ENGINE
24. OUTLET WATER GAP, ENGINE
25. BOLT (M8×35)
26. CVT SUPPORT COVER
27. SPRING WASHER（φ12）
28. BOLT，FLANGE（M12×1.75×30）
29. FLANGE PLATE, CVT SUPPORT
30. BOLT（M10×20）
31. NUT，FLANGE(M12×1.25)
32. BOLT（M10×25)
33. BOLT，FLANGE（M8×25）
34. BOLT，FLANGE（M8×30）
35. STEEL BUSH, STARTING MOTOR
36. STARTING MOTOR

5-6
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

5
Removal and Installation of Front and Rear Axle
Support the vehicle with jack, make sure the vehicle will not fall.
Remove:
--Plastic parts for frame (→Chapter 2)
--Front and rear wheels and arms(→Chapter 8、Chapter 9)
--Air filter (→Chapter 5)
--gearbox (→Chapter 5)
--Engine (→Chapter 5)
-- Front and rear brake caliper
(→Chapter 8、Chapter 9)

Remove front axle.

Remove bolt 1.
Remove drive shaft (front).
Remove bolt 2.
Remove front axle

Installation
Installation as contradictorily process of
remove.
Bolt torque of front axle(M8)：23-25N·m
Bolt torque of front axle(M10)：45-50N·m
Bolt torque of front drive shaft (M8):
23-25N· m

Remove rear axle.

Remove bolt 1.
Remove drive shaft (front).
Remove bolt 2.
Remove front axle

Installation
Installation as contradictorily process of
remove
Bolt torque of rear axle (M8): 23-25N·m
Bolt torque of rear axle (M10): 45-50N·m
Bolt torque of rear drive shaft (M8):
23-25N· m

5-7
 5. REMOVAL OF ENGINE, TRANSMISSION SYSTEM AND GEARSHIFT

Front and rear axle assy disassembly/installation

1. FRONT AXLE
2. FRONT DRIVE SHAFT
3. SPRING WASHER（φ8）
4. BOLT (M8×25)
5. BOLT,FLANGE(M10×1.25×145）
6. BOLT,FLANGE(M10×1.25×85）
7. BOLT，FLANGE（M8×16）
8. LOCKNUT，FLANGE(M10×1.25)
9. HOLDER,FRONT AXLE(FR)
10. HOLDER,FRONT AXLE(RR)
11. AIR HOSE, AXLE(φ6×φ8×450)
12. CLAMP（φ10）
13. REAR AXLE
14. SUPPORT,PARKING CALIPER
15. BOLT(M8×45)
16. CIRCLIP(φ32)
17. BOLT，FLANGE（M12×1.25×115）
18. SUPPORT,REAR AXLE (R)
19. HOLDER,REAR AXLE(RR)
20. LOCKNUT，FLANGE(M12×1.25)
21. COUPLING FLANGE
22. WASHER(φ14×φ28×2) 23. NUT(M14×1.25) 24. PARKING DISC
25. PARKING CALIPER 26. SPRING WASHER（φ8） 27. BOLT(M8×30)
28. REAR DRIVE SHAFT 29. PARKING DISC PAD

5-8
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

CONTENTS

Chapter 1 Reading Instruction ......................................................................................................................................2

1) Reading method of Maintenance Instruction............................................................................................................2
2) Meaning of Marks and Abbreviations ......................................................................................................................3
3) Special Maintenance Tool.........................................................................................................................................4
Chapter 2 Disassembly, Assembly and Maintenance....................................................................................................6
1) Timing Belt...............................................................................................................................................................6
1. Structure Diagram.............................................................................................................................................6
2. Disassembly ......................................................................................................................................................7
3. Installation ......................................................................................................................................................10
2) Camshaft.................................................................................................................................................................13
1. Structure Diagram...........................................................................................................................................13
2. Disassembly ....................................................................................................................................................14
3. Installation ......................................................................................................................................................16
4. Routine Inspection of Valve ............................................................................................................................19
3) Cylinder Head.........................................................................................................................................................22
1. Structure Diagram...........................................................................................................................................22
2. Disassembly ....................................................................................................................................................23
3. Routine Inspection ..........................................................................................................................................23
4) Water Pump ............................................................................................................................................................29
1. Structure Diagram...........................................................................................................................................29
2. Disassembly ....................................................................................................................................................29
3. Cleanup ...........................................................................................................................................................29
4. Routine Inspection ..........................................................................................................................................29
5. Assembly.........................................................................................................................................................29
5) Oil Pump.................................................................................................................................................................29
1. Structure Diagram...........................................................................................................................................30
2. Disassembly ....................................................................................................................................................30
3. Cleanup ...........................................................................................................................................................30
4. Disassembly and Assembly of Engine Oil Pump............................................................................................43
4.1 Structure Diagram.................................................................................................................................42
4.2 Disassembly ..........................................................................................................................................42
4.3 Routine Inspection ................................................................................................................................42
4.4 Installation.............................................................................................................................................44
5. Disassembly of Oil Seal..................................................................................................................................45
5.1 Structure Diagram.................................................................................................................................45
5.2 Disassembly ..........................................................................................................................................46
5.3 Inspection..............................................................................................................................................46
5.4 Assembly of Oil Seal ............................................................................................................................46
6 Assembly..........................................................................................................................................................46
6) Crank Connecting Rod Mechanism........................................................................................................................46
1. Structure Diagram...........................................................................................................................................48
2. Disassembly of Crank Connecting Rod mechanism .......................................................................................48
3. Cleanup ...........................................................................................................................................................49
4. Routine Inspection ..........................................................................................................................................52
5. Assembly of Crank Connecting Rod Mechanism ...........................................................................................53

6-1
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 3 Table of Main Fit Clearance for SQR472 Engine ......................................................................................55

Chapter 4 Table of Measurement Parameters of SQR472 Engine ..............................................................................59
Chapter 5 Table of Main Fitting Torque for SQR472 Engine .....................................................................................61
Chapter 6 Positions on SQR472 Engine to be Lubricated ..........................................................................................62
Chapter 7 Positions on SQR472 Engine to be Spread with Sealant............................................................................65

6-2
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 1. Reading Instruction

1) Reading Method of Maintenance Instruction

１.1 Auxiliary Materials
If it is required in the operation instruction to prepare the auxiliary materials such as special tools, tools, measuring
instruments and grease in advance, you should list all auxiliary materials required in a table before carrying out each
operation.
Since the ordinary tools, lifter and spare parts are conventional materials used in the maintenance, they are omitted
here.
１.2 Operating Sequence and Structure Diagram
(1) The diagram of structure and components, name of components and installation status are set forth at the
beginning of each chapter or section.
(2) The number in the figure refers to the disassembly sequence of each component. The components which may not
be reused and the tightening torque are indicated in the figure.

① Seal Ring
② Engine Oil Pump Cover Sheet
③ Engine Oil Pump Outer Rotor
④ Engine Oil Pump Inner Rotor
⑤ Cotter Pin
⑥ Oil Drain Valve Spring Seat
⑦ Oil Drain Valve Spring
※: Components which may
⑧ Slide Block
not be reused
⑨ Crankshaft Front Oil Seal
Unit: N·m(kg·cm)
⑩ Engine Oil Pump Housing

1 .3 Content Omitted in this Manual

The following operating procedures have been omitted in this Manual, and they should be carried out in the actual
operation:
(1) Operation relating to the lifter and the small-sized elevator;
(2) Cleaning and wipping of common components;
(3) Relevant visual inspection.

6-3
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

1 .4 Definitions

Standard value Refers to allowed value during inspection, maintenance and adjustment.

Refers to the maximum or minimum value that should not be exceeded during
Limit inspection, maintenance and adjustment

Reference Set the standard value for simple measurement to prevent from its measuring
difficulty and inconsistency to facts.

Difference Refers to the difference between maximum value and minimum value.

It carries the cases of damaging the vehicle and parts so you should pay attention
Notice to the operation description.

Warning It records the operation descriptions of cases about person accident.

2) Meaning of Marks and Abbreviations

Mark Original Words Intepretation

RH Right Hand Right Hand
LH Left Hand Left Hand
FR Front Front
RR Rear Rear
IN Intake Intake
EX Exhaust Exhaust
SAE Society of Automotive Engineers Society of Automotive Engineers
API American Petroleum Institute American Petroleum Institute
SPECIAL
Special Tool Special Tool
TOOL
T Torque Torque
Ay Assembly Assembly
S/A Sub Assembly Sub Assembly
W/ With With
M/T Manual Transmission Manual Transmission
A/T Automatic Transmission Automatic Transmission
T/C Turbo Charger Turbo Charger

6-4
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3) Special Maintenance Tools:

Outside view Name or symbol Purpose

Engine disassembly and inspection auxiliary Mount on the engine service

device stand

Disassembly and assembly

Engine service stand
of engine

Disassembly of camshaft
Clamp hole wrench for camshaft timing gears
timing gears

Assembly of camshaft Oil

Spring bushing puller
seal

Valve keeper remove tool

Assembly and disassembly

of valve spring retainer lock

Auxiliary tools

Assembly and disassembly

Flywheel clamp
of crankshaft gear

Disassembly and assembly

Valve guide punch pin
of Valve guide

Axial Oil seal replacing device

Oil seal base drive

6-5
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Outside view Name or symbol Purpose

Disassembly and assembly

Piston pin puller
of piston pin

Embeded combination oil seal and helical

Installation of oil seal
gear puller

Disassembly and assembly

Crankshaft pulley holding tool
of crankshaft pulley

Disassembly and assembly

Wrench
of crankshaft driven gear

Replace valve clearance

adjustment gasket

Water pump pulley locking wrench Assembly of coolant pump

Measuring Feeler gauge. Micrometer caliper. Ruler. Dial gauge. Cylinder gauge. Caliber. Pressure gauge. Torque
tools wrench torque wrench
Tool Piston ring extractor

Oil Engine Oil, adhesive

6-6
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 2. Disassembly, Assembly and Maintenance

Disassemble or assemble the engine with roll over stand.

Disassemble or assemble the engine parts on the roll over
stand.

1) Timing Belt

1. Structure Diagram

① Water pump pulley

② Timing shroud
③ Timing belt
④ Torsional damper
⑤ Timing belt back plate
⑥ Tension pulley
⑦ Camshaft timing pulley

※: Components which may

not be reused.
Unit: N·m(kg·cm)

6-7
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2. Disassembly
2.1 Remove the water pump pulley as the view showing.
It will be better of disassembling with special tool.
Torque: 25±1.5 N.m

2.2 Disassembly of Timing Belt Cover

Torque: 6±1N.m

2.3 Disassembly of torsional damper

Use special tools to prevent the gear ring from
rotating. When disassembling the fixing bolts of the
torsional damper, make sure that the marks on the
crankshaft timing pulley match with the timing marks
on the engine oil pump.

2.4 Remove the timing belt back plate.

6-8
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.5 Disassembly of tension pulley

2.5.1 Compress the top dead center at the first cylinder
Timing Mark Clockwise
piston. After disassembly of timing cover, pull the
bolt and clockwise rotate the timing gear with
wrench. And then align the timing mark of camshaft
timing gear and the raised mark on camshaft cover;

Timing Mark

2.5.2 Screw off the bolt of tension pulley and remove the
tension pulley.

2.6 Disassembly of timing belt

Notice: Do not use sharp tools like screwdriver during
disassembly of belt.
Notice: Pay attention to the following items during using
the timing belt:
l Do not bend the belt with small angle, or the rigging in
belt will break.
l Do not pollute grease and water because the using
expectancy of belt is short.
l Only clockwise rotate the engine after mounting the
belt.
2.7 Disassembly of crankshaft timing gear

6-9
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.8 Inspect the timing belt carefully, and replace new components under any of the following circumstances or when
the mileage is up to the conditions of replacement:
2.8.1 Chap of back-side rubber
2.8.2 Chap of dedendum, chap of separated cord fabric.
2.8.3 Wearing, gear missing and incomplete gear of cord fabric.

Chap

Wearing

Chap

2.8.4 Abnormal wearing of belt flank.

Gear

Abnormal Fall off with

2.8.5 Notice: Replace the belt as any following situation occurs, even though abrasion cannot be found directly:
The water pump leaks water out, and requires continuing infusion.If the belt is spotted with much oil stains, and the
rubber may be damaged due to expansion, you should replace the belt.

Timing belt model and type

Part number 372-1007081
Width of belt ２５.3mm

Tension Pulley of Timing BeltRotate the bolt of tension pulley bracket and hear if it is noisy; check the contacting
surface and look if it is damaged.Model and type of tension pulley of timing belt
Part number 372-1007030
Width ２７.０mm
Outer diameter φ50mm

Check if the out is damaged.Timing belt model and type

Type ＥＦ
Item ＧＬ, ＺＬ, ＧＳ, ＺＳ
Camshaft timing pulley diameter(mm) φ110.7+0.1-0.2
Camshaft timing pulley diameter(mm) φ54.65+0.7-0.13

6-10
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Check the timing belt back plate for any deformation.

Standard size of crankshaft timing gear
Width 28.6mm

3. Installation
3.1 Assembly of crankshaft timing pulley.

3.2 Installation of timing (at the top dead center of the Timing Mark
first cylinder piston)
3.2.1 Put the camshaft timing gear on the front end of the
exhaust camshaft, align the locating slot on the gear with
the locating pin on the end of the camshaft, and then fix
the timing gear with bolts. The tightening torque for the
bolts is 100±5Nm.

Make sure that the clashing mark of crankshaft timing

pulley aligns with the mark of oil pump.

Timing Mark

3.3 Install the tension pulley. After adjust the tension of

timing belt, install the tension pulley bolt and tighten it
with the torque specified. Adjust the tension of the timing
belt acording to the following instruction, and install the
tension pulley.
3.3.1 As indicated in the figure, make the tensioner
swing to the right with a screwdriver so that the distance
between the edge of the tension pulley and the circular arc
of the water pump body is 8mm, and then tighten the
tension pulley bolts with the torque of 25±3Nm.

6-11
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.3.2 Rotate the crankshaft along the rotating direction of

the engine for 2 rounds so that the timing mark on the
timing gear of camshaft and crankshaft is matched
respectively, and then tighten the crankshaft belt pulley
bolts.

3.3.3 The force required to press down the central

position between the 2 pulleys at the in-tension side of the
timing belt for about 5mm is:

［Reference］ 19.6-29.4N(2.0-3.0kg)

Notice: when the deflection can not reach the standard, it

is necessary to adjust the fixing bolt of tension pulley
mentioned above.
Tighten the fixing bolt of the tension pulley with the torque
as specified. The tightening torque is 25±3N.m

3.4 Assembly of Timing Belt Back Plate.

Notice: Install the timing belt back plate in the direction as
indicated in the right figure. Inside Outside

3.5 Install the torsional damper with special tools.

3.5.1 Without flywheel
3.5.1.1 Hitch the part of crankshaft pulley with the belt
of special tool.

3.5.1.2 Hold on the handle of the special tool and

prevent the toothed belt from rotating. Tighten the bolts
with the specified torque.

Torque: 98.0±10N.m{10±1kgm}

6-12
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.5.2 With flywheel

3.5.2.1 Prevent the gear from rotating with special tool.
3.5.2.2 Then screw down the bolt of torsional damper.

3.6 Assembly of timing cover.

Mount the sealing strips at the positions as indicated in the
right figure. The sealing strips at the position 1 and 2 1
should be mounted before the assembly of the cylinder
head assembly, and the sealing strip at the position 3
should be mounted before tightening the water pump.
2
3

Install the timing cover, screw in the bolts with hand and
then tighten them.
Torque: 6±1N.m

3.7 Installation of water pump pulley.

Torque: 6±1N.m

6-13
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2) Camshaft

1. Structure Diagram

(1) Cylinder head chamber cover assembly

(2) Cylinder head cover gasket
(3) Camshaft timing belt
(4) Camshaft cover
※: Components which may
(5) Blanking cover
not be reused
(6) Camshaft bearing cap
Unit: N·m(kg·cm)
(7) Exhaust camshaft assembly
(8) Intake camshaft assembly
(9) Camshaft oil seal
(10) Axial spring retainer ring
(11) Saddle washer
(12) Intake camshaft sub gear
(13) Transmission ring

6-14
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2. Disassembly
2.1 ① Cylinder head chamber cover assembly;
② Disassembly sequence of cylinder head
chamber cover;

2.2 Remove the camshaft timing gear with special tool.

Notice: ·The special tool should be made as indicated in

the right figure.
·Use the special tool to prevent the camshaft from
rotating.

2.3 Remove the camshaft bearing cap

2.3.1 The marks on the camshaft gear should match Timing Mark

with each other as indicated in the right figure.

Gear of Exhaust Gear of Intake

Camshaft Camshaft

6-15
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.3.2 Position the main sub gear on intake camshaft

with bolts, as can be seen from the right picture. Fixing Bolt
Notice: In order to eliminate the radial force of the
camshaft, the camshaft should be kept at the horizontal
position in the course of disassembly so as to prevent the
damage caused by the excessively high radial force.

2.4 Disassemble the bolts in the order as indicated in the

right figure, and then disassembly the camshaft bearing
cap.

2.5 Remove the spark plug

2.6 Disassemble the sub gear of the camshaft.
2.6.1 If using the special tools, operate as indicated in
the right figure.

Clamp the camshaft and plug the pins of special tool into
the hole on gear; rotate the gear to keep the meshing of
driven gear and driving gear, and then remove the fixing
bolt of driven gear.
Notice: The surface of the camshaft may not be damaged.

2.6.2 If not using the special tools, operate as indicated

For Fixing
in the right figure.
(1) Screw M6 bolts onto the sub gear of the intake
camshaft at the position as indicated in the right figure.
(2) Use the screwdriver to turn the gear as indicated in
Bolt
the figure, and disassemble the fixing bolts of the sub
gear.
Notice: The surface of the camshaft may not be damaged.
(3) Disassemble the axial elastic retainer ring with
tensioner and remove the saddle spring washer,
transmission ring, and so on.
2.7 Camshaft

6-16
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.7.1 Measure the camshaft with micrometer caliper. If it

is below to the specified limit, replace with a new one.
Camshaft journal Unit: mm
Type EF
Item ZL, RL GL, GS, ZS

IN φ23.0-0.02-0.033
Standard value
EX φ23.0-0.02-0.033

IN φ22.9
Limit: 0.10
EX φ22.9

2.7.2 Inspection of camshaft axial clearance

(1) Replace the camshaft when the axial clearance value
measured with dial gauge exceeds the standard value.The
axial clearance of intake camshaft is 0.1~0.170mm.
The axial clearance of exhaust camshaft is 0.1~ 0.173mm.
Limit: 0.18mm.

2.7.3 Inspect the clearance of the engaging tooth of

camshaft
(1) Install the camshaft into the cylinder head.
(2) Confirm the mark forwards on the bearing cap as
well as the axle number, and then tighten the bolts.
(3) Measure the clearance of engaging tooth of the intake
camshaft with dia indicator.
Notice: ·Measure at 4 points on the circle of the piston
·Turn the intake camshaft with special tools.
·Make sure that the marks on the driven gear and
the driving gear of the camshaft match with each
other.
Inspect the clearance of the engaging tooth of camshaft:
Item Standard value Limit
Single tootj 0.04-0.13 0.30

3. Installation
3.1 Under the circumstance that special tools are used:
3.1.1 Fix the 2 holes (φ6) of the camshaft gear
assembly with special tool.
3.1.2 Rotate the driven gear to the right with special
tool and tally the mark hole of driven gear with that of
camshaft driving gear, or their marking way complies with
each other, fix the driven gear with bolts.(Thread: M5;
Thread pitch: 0.8)

For Fixing

6-17
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.2 Under the circumstance that special tools are not

available:
3.2.1 Screw the M6 bolts into the camshaft driven gear
at the position indicated in the right figure. Insert a Bolt
screwdriver into the gap between the M6 bolt and the
camshaft journal and trun the driven gear rightwards so
that the fitting mark of the 2 gears match with each other
or the tooth head of the 2 gears accord with each other, and
then fix the driven gear with bolts (M5×0.8).
Notice: Don’t damage the journal, adjust the operation.

3.3 Assembly of camshaft

Notice: Pay attention to the axial clearance of the camshaft
3.3.1 Spread grease on the gear of camshaft and the axial
of cylinder head. Timing Mark

3.3.2 Remove the fixing bolts for camshaft driven

gear after mounting the camshaft.
3.3.3 Mount the camshaft, align the timing mark as can
be seen from the right picture

Gear of Exhaust Gear of Intake camshaft

3.3.4 Spread oil fully on the cam of camshaft assembly,

gears and axial of cylinder head.

3.4 Tighten the camshaft bearing cap by the order of right

picture.

For Fixing
3.5 Screw off the fixing bolts for driven gear of intake
camshaft assembly.

6-18
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.6 Assembly of camshaft cove

Spread sealant on the position (slot) of camshaft cover as Glue Spread Line
can be seen from the right picture.

3.6.1 Assembly of Camshaft Cover

Tighten the bolts in the order as indicated in the right
figure and with the specified torque.

3.6.2 After spreading oil on the blanking aperture of

cylinder head and the mounting surface of blanking cover,
press the blanking cover with special tool.
Notice:·The blanking cover should be installed in the
direction as indicated in the right figure.
· After being pressed, the blanking cover should be
1±1mm higher than the surface of thecylinder Outside
head.

3.7 Spread the edge of the camshaft oil seal with oil, and
press it into the cylinder head with M10 bolt (length:
50-60mm) and special tools.
Notice:· If the oil seal is reused, spread it with oil before
pressing it into the cylinder head.
· After removing the bolt, knock it with hand so as to
inspect and confirm it.

3.8 Assembly of camshaft timing gear

After spreading sealant on the bolt, prevent it from rotating
with special tool and screw down the bolt of camshaft
timing gear in specified torque.
Torque: 100±5N.m

Notice: Process the special tools as indicated in the right

figure before using them.

6-19
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.9 Installation of cylinder head cover

3.9.1 The old cushion of the timing belt cover which
contacts the cylinder head cover should be removed
completely.
3.9.2 Put the new cushion into the gloove of the timing
belt cover accurately.
3.9.3 Mount the cylinder head cover on the cylinder
head, and tighten the 8 bolts in the order as indicated in the
right figure and with the specified torque.
Torque: 6±1N.m

4 Inspection of valve
Timing
4.1 Standard valve clearance:
Valve clearance IN 0.18±0.05
EX 0.25±0.05

4.2 Make sure that the timing mark on the camshaft

driving gear is aligned with that on the camshaft driven
gear.

Gear of Exhaust Gear of Intake

4.3 Inspect the valve clearance as specified in the figure

below with the feeler gauge

Cylinder 1 Cylinder 2 Cylinder 3 Cylinder4

IN EX IN EX IN EX IN EX
O O O — — O — —

4.4 Rotate the camshaft for a round to the position as

indicated in the figure, and then measure the valve

6-20
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

clearance once again:

Cylinder 1 Cylinder 2 Cylinder 3 Cylinder 4
IN EX IN EX IN EX IN EX
— — — O O — O O

If the clearance exceeds the standard value, adjust it by

replacing the adjustment gasket.
Notice: The position at which the measurement result
exceeds the standard value as well as the measurement
result should be recorded.

4.4.1 Rotate the camshaft and make the cam head of the
cylinder which exceeds the standard value faces upwards
and the opening of the valve tappet face inwards.

4.4.2 Rotate the crankshaft and press down the valve

tappet with the crown head of the cylinder cam.

4.4.3 As indicated in the right figure, put special tools on

and around the valve tappet from the inside of the cylinder
head, and then rotate the crankshaft so that the crown head
of the cam face upwards. Press the valve tappet with
special tools and hold on.

4.4.3.1 Pry out the adjustment gasket with screw driver,

remove the gasket inside with magnet.

4.4.3.2 Adjust the thickness of adjustment gasket with

6-21
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

micrometer caliper.

4.4.3.3Select the gasket on the basis of the standard

value of valve tappet
① Intake valve
Select gasket thickness = Unload thickness +
(Measured valve clearance -0.25mm)
② Exhaust valve
Select gasket thickness = Unload thickness +
(Measured valve clearance -0.25mm)

[Reference] The 32 kinds of gasket with different

thickness are listed in the following table:
2.18 2.40 2.62
2.20 2.42 2.64
2.22 2.44 2.66
2.24 2.46 2.68
2.26 2.48 2.70
2.28 2.50 2.72
2.30 2.52 2.74
2.36 2.58 2.80
2.32 2.54 2.76
2.38 2.6

4.4.3.4 Adjust the valve clearance with selected

adjustment gasket.
Low
Notice: Install the adjustment gasket with its identification
mark facing downwards.

4.4.3.5 Rotate the crankshaft so that the crown head of

the cam faces downwards and presses down the the valve.
Pick up the special tool.
4.4.3.6 Rotate the crankshaft for 2-3 rounds and confirm
once again the valve clearance. If it is still beyond the
scope of standard value, adjust and inspect the valve
clearance according to the operation specified in 4.1-4.4.

3) Cylinder Head

1. Structure Diagram

6-22
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

1 Spark plug 20±1Nm

2 Cylinder Head
3 Weather Strip I
4 Cylinder cushion
5 Adjustment gasket
6 Valve tappet
7 Valve spring retainer
8 Valve spring seat
9 Valve Spring
10 Intake valve
11 Exhaust valve
12 Valve oil seal ※: Components which may not be
13 Valve seat reused

14 Valve guide

2. Disassembly
2.1 Disassembly of spark plug

2.2 There are 8 boltes on the cylinder head. In the course

6-23
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

of the assembly of cylinder head, slowly tighten these bolts

in the order as indicated in the right figure for several
times untill ther are tightened properly.
Notice: Remove the cylinder head bolts with a torque
socket wrench in the contrary order.

2.3 Disassembly of cylinder head and cylinder head

gasket
Notice: The cylinder head gasket is nonreusable.

2.4 Disassembly of valve adjustment gasket and valve

tappet
2.5 Disassemble the valve spring retainer lock, spring
retainer, spring seat, valve spring, intake valve, and
exhaust Valve etc with special tools.
2.6 Disassembly of valve oil seal and valve spring gasket

2.7 Cleanup
2.7.1 Clean the carbon dust on the valve.
2.7.2 Clean the bottom surface of cylinder head and the
surface of intake and exhaust manifold with scraper knife.
Notice: The surface of the cylinder head may not be
scratched in the course of cleanup.
Do not pollute the intake port and water passage.

3. Routine Inspection
3.1 Cylinder Head
Measure the flatness at each point with ring gauge as
indicated in the figure.
Cylinder head: 0.10mm
Surface of intake/exhaust manifold: 0.10 mm。

3.2 Valve Spring

3.2.1 Measure the square degree of valve spring with
square. Replace if it exceeds the specified value.
Limit: 1.2mm

6-24
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.2.2 Measure the free state of the spring.

Standard value: 37mm

3.3 Inspection of valve

3.3.1 Check if it is deformed or abrades.
Inspection of valve Unit: mm
Limit:
Item Standard value
0.10
IN 0.85～1.41 —
Width of seal Thickness of
EX 1.07～1.36 — Measurement
Top
Thickness of top IN 1.0±0.2 0.75 Position of Outer
of valve EX 1.0±0.2 0.75 Diameter

3.3.2 Check the clearance of valve guide and valve stem.

3.3.2.1 Measure the inside diameter of valve guide with
dial gauge, the outer diameter of valve stem with
micrometer caliper.
3.3.2.2 Figure out the difference of measured values and
the clearance. If the clearance is beyond the specified
value, replace valve or guide.
Notice: As can be seen from the right picture, at measuring
point, work out the clearance of last abrasion part. Measurement
Item Standard value Limit: 0.10 Point
Valve guide inside
φ5.0 —
diameter(mm)
Valve guide outer
φ5.0 —
diameter(mm)
0.056～
IN 0.07
0.020mm Measurement of Valve Guide Inside Diameter
Clearance
0.066～
EX 0.08
0.030mm
Measurement Point

6-25
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.3.3 Replacement of valve guide.

3.3.3.1 Heat the cylinder head with hot water to 80-100
℃.
3.3.3.2 Take out the valve guide from one side of
combustion chamber with special tool, as can be seen from
the right picture.
Notice: The removed valve guide may not be reused.
The intake valve guide and the exhaust valve guide may
not be mis-installed.

IN Use EX Use

3.3.3.3 Mount the new valve guide with special tool at

the place as can be seen from the right picture.
Notice: strike the conduit slowly to the position in the
cylinder head; do not strike too far and be careful for size.

The height of the part of valve guide struck into the

cylinder head:
Type EF
Item
GL, ZL, RL, GS, ZS
Height (mm） IN 13.71±0.25
EX 12.11±0.25
3.3.3.4 Rub the inside diameter with reamer to reach the
standard clearance value.

3.3.4 Assorted surface of valve

3.3.4.1 Spread with red lead on the assorted surface of
valve. Do not rotate the valve but press lightly and check
the assortment and width.

6-26
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.3.4.2 Repair of valve seat insert

Notice: The repair of valve seat is always conducted in
the course of the inspection of valve’s fitting position. The
surface repaired should be free from any breakage. Take it
out slowly after the inspection.

3.3.4.3 45wimble surface is assorted standard value.

3.3.4.4 Inspect the fitting position of the valve. The best
position is the center of the valve. If no the valve should be
adjusted.
3.3.4.5 Cut wimble surface at the center of assorted
position with inner 70and outer 30

3.3.4.6 Prepare for polishing of valve seal.

3.4 Assembly of cylinder head

3.4.1 Cylinder head
Pay attention to the following for installing the other
auxiliary part of cylinder head:

3.4.2 Protective tube of spark plug

1. Press the protective tube of spark plug into the
protective tube hole on the cylinder head with the special Protective Tube of Spark Plug
auxiliary tool. Before pressing, spread the protective tube
with sealant. The pressing depth is indicated in the right
figure.
Notice: Pay attention to the pressing depth and the
uprightness to top of cylinder head when pressing.
During pressing, the protective tube can not be deformed,
or leaking will be occurred at the cylinder head cover.

6-27
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

3.4.3 Installation
3.4.3.1 Assembly of valve spring washer and valve oil
Auxilary Tool of Valve Spring Assembly
seal
3.4.3.1.1 Clamp the special auxiliary tool on the top of Valve
valve stem and spread oil around the auxiliary tool and the
Valve Oil Seal
inner of new valve oil seal. Then mount it at the position as
can be seen from the picture and pull out the mounting
auxiliary tool of valve oil seal. Assembly Lower Surface of
[Reference] After being pressed down, the size of Valve Spring
the oil seal should comply with the value
indicated in the right figure.

3.4.3.2 Assembly of intake valve and exhaust valve

3.4.3.2.1 Assembly of valve spring.
Notice: The painting is used for recognizing the different Painting
suppliers, so the same engine should use the valve spring
with same painting.

3.4.3.3 Assembly of valve keeper

Warning: Operate with goggle for protecting the eyes.
·Be care for spring jumping out.
After assembly of valve spring and its seat, press the valve
spring with special tool and mount the valve keeper.

3.4.3.4 Assembly of valve tappet and valve clearance

adjustment gasket
3.4.3.5 Mount the cylinder head gasket and recognize
the direction of front and back.

3.4.4 Assembly of dust seal and cylinder head

6-28
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

assembly Oil Spread

3.4.4.1 Spread a little oil on the flange side of bolt and Position
threaded part

3.4.4.2 Tighten the cylinder bolts in the order indicated

in the right figure for 3 times till the torque reaches the
specified value. The tightening torque for each time is set
forth as follows:
First time: 30±2Nm; second time: 50±3Nm; third time:
70±3.5Nm
Torque: 70±3.5N.m

3.4.4.3 Mount spark plug

Torque: 20±1Nm
Notice: Tools should be vertical to prevent the protective
tube of spark plug from distorting, or the oil will leak.

6-29
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4) Water Pump

1. Structure Diagram

Components which

may not be reused

① O-ring (nonreusable)
② Water pump body
③ Dust seal

2. Disassembly
2.1.○
1 Disassembly O-ring
Notice: The O-ring is nonreusable.
2.2 Screw off 3 bolts and disassemble water pump body.

2.3. Disassembly of dust seal

3. Cleanup
3.1 Clean water pump joint surface.

4. Routine Inspection
4.1 Check if it is deformed.
4.2 Rotate it with hand and inspect whether the rotor
rotates and is lubricated well.

5 Assembly
5.1 Mount Dust seal.
5.2 Mount Water Pump Body; torque: 25±1.5N.m.
5.3 Mount The New O-ring.

6-30
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

5) Oil Pump

1. Structure Diagram

Components which

may not be reused

① Torque for oil pan bolt: 8±2 N.m

② Oil collector
③ Oil collector spacer (nonreusable)
④ Oil pump
⑤ Oil pump spacer (nonreusable)
⑥ Rear oil seal bracket

2 Disassembly
2.1 Screw off the bolts and nuts, and then remove the oil
pan from the cylinder body with special tool (The engine is
placed on the disassemble shelf upside down).
Notice: Don’t make the oil pan flange deform.

6-31
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.2 Remove the engine oil drainer, engine oil collector

gasket
Notice: The oil collector gasket is nonreusable.

2.3 Remove the engine oil pump assembly and the engine
oil pump gasket.

2.4 Remove the rear oil seal bracket.

3. Cleanup
3.1 Remove the old cushion from the oil pan, oil pump
and oil pan bracket with a scraper or shovel.
Notice: Don’t let the fragment of the cushion fall into the
cylinder.

6-32
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4 Disassembly and Assembly of Engine Oil Pump

4.1 Structure Diagram

① Seal Ring
② Engine Oil Pump Cover Sheet
③ Engine Oil Pump Inner Rotor
④ Engine Oil Pump Outer Rotor
⑤ Cotter Pin ※ : Components which may
⑥ Oil Drain Valve Spring base not be reused
⑦ Oil Drain Valve Spring Unit: N·m(kg·cm)
⑧ Slide Block
⑨ Crankshaft Front Oil Seal
⑩ Engine Oil Pump Housing

4.2 Disassembly
4.2.1 ① O-ring
Notice: The O-ring is nonreusable.

4.2.2 Remove the oil pump cover

Notice: If the screws are tightened, use a screw driver
to remove them as indicated in the figure.

4.2.3 Remove the inner rotor, outer rotor of the engine

oil pump.

6-33
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4.2.4 Remove the cotter pin

Notice: The cotter pin is nonreusable.
Notice: When removing the cotter pin, be careful not to
let the spring or the spring seat spring out or fall off
abruptly.

Relief Valve

4.2.5 Remove the spring seat of the oil pressure relief Slide Block Relief Spring Spring Seat
valve for the engine oil pump, the coil spring, oil pump
and oil pressure relief valve etc.

4.2.6 Remove the front crankshaft oil seal.

Notice: The oil seal removed may not be reused.

4.3 Routine Inspection

Mark
4.3.1 Inspect the engine oil pump for clearance.
4.3.1.1 According to the marks for inner gear and outer
gear in the engine oil pump, put the gears into the engine
oil pump that is in the cylinder block.

4.3.1.2 Measure the clearance between the inner and

outer gears with a feeler gauge
Standard value: 0.05-0.18mm (average value of 9
positions)
Limit: 0.35 mm

6-34
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4.3.1.3 Measure the clearance between the rotor and

pump body.
Standard value: 0.10-0.181mm
Limit: 0.25 mm

4.3.2 Inspect the oil pressure relief valve

4.3.2.1 No abrasion or scrape shall be found on the oil
pressure relief valve.

4.4 Installation
4.4.1 After the lip of the new oil seal for front crankshaft Special Tool
is spread with engine oil, fix it with a special tool.

Notice: ·Use new oil seal

·The oil seal should be left less than 0.5 mm at its
outer edge after it is pressed down.
Pressed Direction Inner Side

Oil Seal

Below 0.5mm

4.4.2 Assembly of the oil pressure relief valve for engine

oil pump and the cotter pin.
Notice: The cotter pin is nonreusable.

6-35
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4.4.3 When the outer gear or inner gear is put into the
engine oil pump, its mark should be seen. Mark

4.4.4 The new weather strip should be fixed in the

groove of oil pump cover.

5. Disassembly of Oil Seal

5.1 Structure Diagram

Components which
may not be reused

6-36
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

5.2 Disassembly
5.2.1 Remove the rear crankshaft oil seal with a
screwdriver.
Notice: The rear oil seal of the crankshaft is nonreusable.

Lip
5.3 Inspection
Inspect the oil seal for damage and the abrasion at its lip.

5.4 Assembly of oil seal

5.4.1 Spread engine oil over the lip of the new oil seal.
5.4.2 Mount the oil seal with special tool as indicated
in the right figure
Special Tool

Special Tool

6. Assembly Glue Spread Line

6.1 Assembly of the oil seal seat

Spread sealant over the oil seal seat as shown in the right
figure.
Grease: Loctite 5699

Notice: Spread the liquid sealant on the position of the

oil seal base which is to contact with the cylinder body,
and make sure the width of the sealant is 3-4mm.
Torque: 25±1.5N.m

6.2 Assembly of the new engine oil pump gasket and the
engine oil pump assembly.
Torque: 20±1.5N.m

6.3 Assemble the new engine oil collector gasket and the
6-37
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

engine oil drainer

Torque: 6±1N.m

6.4 Assembly of the oil pan

6.4.1 Clean up the joint surface between the oil pan with
the cylinder.
6.4.2 Spread sealant, then assemble it.
Grease: Loctite 5699
Notice: ·The sealing line should be unbroken with its
diameter being ф3-4mm
·Assembly should take place fifteen minutes
after glue-spreading.

6.4.3 Tighten the bolts in the middle first up to the

specified torque, then the bolts beside them as shown in
the right figure.
Torque: 6±1N.m Front Rear

6-38
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

6) Crank Connecting Rod Mechanism

1 Structure Diagram

Components which may

not be reused

① Connecting rod cover

② Connecting rod bushing
③ Piston connecting rod assembly
④ Main bearing cap
⑤ Crankshaft
⑥ Crankshaft bearing bushing
⑦ Thrust plate
⑧ Cylinder body
⑨ First ring
⑩ Second ring
⑾ Steel tape combined oil ring
⑿ Piston
⒀Connecting rod
⒁ Piston pin

6-39
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2 Disassemble of Crank Connecting Rod Mechanism

2.1 Inspect the axial momentum of the connecting rod
2.1.1 Measure the axial clearance with a dial gauge or
feeler gauge.
Standard value: 0.15-0.25mm
Limit: 1.2mm
2.2 Inspect the connecting rod bushing for its radial
clearance.
2.2.1 Remove the bushing cap.
Notice: The components of each cylinder shall be placed
in order.
2.2.2 Clean the bearing bushing and the axle.

2.2.3 Conduct radial adjustment for the axial diameter of

connecting rod with clearance gauge.
Tighten the bushing cap with specified torque.
Torque: 40±2N.m

Notice: The crankshaft may not rotate.

2.2.4 Remove the bushing cap, measure the maximum

thickness of the searcher.
Standard value: 0.020-0.044 mm
Limit: 0.07 mm

6-40
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.2.5 If it is beyond the limit, replace the bearing

bushing.
Notice: Replacing the bearing bushing with the product
of the same manufacturer’s brand. The thickness of the
connecting rod bushing which meets the requirements of Connecting Rod
clearance = diameter of big end hold – axial diameter of Connecting Cover
connecting rod – standard value of bearing bushing
clearance

2.2.6 Remove the connecting rod bearing cap and the

connecting rod bearing bushing

2.2.7 Put vinyl-resin protecting jacket on the threaded Protection Sleeve

part of the connecting rod bolt so as to prevent the bolts
from scraping the cylinder hole and the crannkshaft
connecting rod journal, and then disassemble the piston
connecting rod by using the hammer handle striking it out.

2.3 Inspect the axial clearance of crankshaft

2.3.1 Measure the axial clearance of the crankshaft with
a dial gauge, if it is beyond the limit, it is necessary to
replace the axial thrust plate or the crankshaft.
Standard value: 0.089-0.211mm
Limit: 0.30mm
Item Standard value
1.9-0.11-0.03

6-41
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.4 Inspect the crankshaft for its radial clearance.

2.4.1 Remove the crankshaft bearing cap by softly
tapping with a resin hammer.
2.4.2 Clean the inside and surface of the bearing bushing,
the inside and surface of the bearing cap, the cylinder wall
and journal. Inspect them for abrasion and damage
carefully.

2.4.3 Adjust the radial clearance of the crankshaft with a Protection Sleeve
clearance gauge, and tighten the bearing bushing cover
bolts with the specified torque.
Torque: 70±3.5N.m
Clearance Gauge
Notice: After tightening the bolts, the rotating torque of
the crankshaft should be less than 1Nm
（The torque of crankshaft without piston connecting rod）

2.4.4 Remove the bearing cap and measure the maximum

width with a clearance gauge. If the measurement result
exceeds the limit, replace the bearing bushing.
Standard value: 0.025-0.069mm
Limit: 0.10mm

Width Compare of Clearance Gauge

2.4.5 Remove the main bearing bushing cap of the

crankshaft, crankshaft, crankshaft bearing bushing and
crankshaft axial thrust plate
Notice: Tighten the bolts for the crankshaft bearing cap
in the order shown in the right figure. Tighten the bolts for
three times, then the torque must be up to the specified
value.

6-42
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

2.5 Disassembly and assembly of the piston and

connecting rod assembly
2.5.1 Remove the first ring, second ring and the oil
ring with a pair of piston ring moving pliers.
Notice: Don’t get the piston and piston ring of each
cylinder confused.

2.5.2 Remove the piston, connecting rod and the

piston pin with special tool.

Special Tool
Disassemble the piston pin with special tool as indicated in
the right figure.

① As indicated in the right figure, disassemble the piston

Special Tool
which is at the state mentioned above with special
tools. Remove the piston pin with special tool, and
then remove the piston and the connecting rod.

3 Cleanup
3.1 Cylinder Body
Warning: In the course of cleanup, protect your eyes
with eyeglass.

3.1.1 Clean up the cylinder body, cylinder head, oil

pan, oil pump and the oil seal with a flat blade.

3.2 Piston
Warning: In the course of cleanup, protect your eyes
with eyeglass.

3.2.1 Use an old ring to remove the carbon in ring

groove.
3.2.2 Remove the carbon of parts with scavenger.
Notice: Don’t use hard articles such as metal brush.

6-43
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4 Routine Inspection
4.1 Cylinder Body
4.1.1 Inspect the top surface of cylinder body for its
flatness
(1) Measure at the six points shown in the right figure
with a ruler and a feeler gauge.
Limit: 0.08mm

4.1.2 Use of bore gauge

Measure the cylinder bore at the positions as indicated in
the right figure with a bore gauge, and figure out the
Upper Stopper Position of Piston
difference between the maximum value and the miximum
value. If the difference exceeds the limit, repair or replace
the cylinder.
Limit: 0.03mm
[Reference] Roundness: A-B or a-b Lower Stopper Position of Piston
Cylindric degree: A-a or
[Reference] Standard diameter of cylinder:
φ72.00-72.01mm

4.2 Piston
Measurement Position of
4.2.1 Inspect the piston pin hole for its clearance
Piston Pin
Measure the piston pin at several positions with a
micrometer caliper shown in the figure, make the
maximum value as the diameter of pin.

4.2.2 Measure the diameter of piston pin at several

positions with an inner-diameter dial gauge as shown in the
figure, make the minimum value as the diameter of the pin
hole.

Work out the clearance with the difference between the

pin diameter and pin hole diameter, if the difference is
beyond the standard value, replace the piston pin or piston.
Standard value: 0.004-0.009mm
Limit: 0.015mm

6-44
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4.2.4 Measure the diameter of the piston

4.2.4.1 Measure at about 11 mm to the bottom of the
piston, along the direction vertical to the piston pin.

φ 72
-
0.013

Standard value: -0.025

4.2.5 Inspect the clearance between the piston ring and

the ring gloove
4.2.5.1 Measure around the ring gloove with a piston
ring and a feeler gauge
Standard value Limit
(mm) (mm)
First ring 0.03~0.06 0.12
Second
0.03~0.06 0.11
ring

4.2.6 Inspect the end clearance of piston ring

4.2.6.1 Put the piston ring 45mm below the top surface
of the cylinder hole. Press down the piston ring with the
piston head, and then measure the opening with a feeler
gauge.
Standard value Limit
(mm) (mm)
First ring 0.25-0.40 0.65
Second
0.35~0.50 0.65
ring
Oil ring 0.20~0.70 1.00

6-45
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

4.2.7 Inspect the clearance between the piston and

cylinder wall
Measurement position of piston
4.2.7.1 Measure the inner diameter of the cylinder and
Outer Diameter
the outer diameter of the piston at the positions as
indicated in the right figure. If the measurement results
Measurement
exceed the limit, replace the piston or cylinder.
position of piston
Standard value: 0.018～0.030
Inner Diameter
Limit: 0.10
[Reference] The clearance between the piston and cylinder
bore is controlled by the difference between the minimum
inside diameter of piston hole and the maximum outer
diameter of piston.
4.2.7.2 After replacing the piston or the cylinder body,
confirm the clearance again
Standard value: 0.018～0.030

4.3 Crankshaft
4.3.1 Inspect the proper alignment of the main axle
diameter.
4.3.1.1 Measure the proper alignment with a dial gauge,
if the proper alignment is beyond the limit, replace the
crankshaft.
Limit: 0.03mm
Notice: The bending value should be equal to
one-second the run-out value of crankshaft rotating one
circle.
4.3.2 Inspect the crankshaft for the abrasion.
4.3.2.1 Measure the connecting rod journal at the
positions indicated in the left figure with a microcaliper,
and figure out the roundness and cylindricity.
Limit: 0.005mm

4.3.2.2 Measure the connecting rod journal at the

positions indicated in the right figure with a microcaliper,
and figure out the roundness and cylindricity.
Limit: 0.004mm

5 Assembly of Crank Connecting Rod

mechanism
5.1 Assembly of the piston connecting rod

6-46
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

5.1.1 Assemble the piston, connecting rod and the

Mark Forward
piston pin with special tool following the instructions
below:
5.1.1.1 Spread engine oil over the pin hole of the
connecting rod, assemble according to the group mark and
direction mark of piston and connecting rod.

5.1.1.2 Assemble the piston and the connecting rod with

special tools shown in the right figure. Align and Straight

5.1.1.3 Adjust and assemble the piston and connecting

rod as indicated in the right figure. Spread the piston pin
with oil and then assemble the piston and connecting rod
with a oressing machine.

Notice: When pressing in the piston pin, make sure the

fitting direction is correct.
·When the piston pin is pressed into the piston, the
small end of the connecting rod should be heated
to 300℃, and the pin should be aligned properly.
Section Shape
Mark
0
5.2 Install the first and second pistion ring and the oil ring 1st Ring
according to the following instruction:
5.2.1 Installation of piston ring 2nd Ring
Make the side with marks face upwards, and then fix it
with piston pin tools. Oil Ring

Lower Blade

1st Ring 2nd Ring

5.2.2 Mount the steel tape combined oil ring (bushing
ring lower, lower blade, upper blade) firstly, and then
Front Rear
mount the second gas ring, and finally mount the first gas
Bushing
ring. Opening angles of rings are shown in the figure:
Ring

Upper Blade

6-47
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

5.3 Resemble the crankshaft main bearing cap,

crankshaft, crankshaft bearing bushing and the crankshaft Thrust Plate
axial thrust plate, pay attention to the following:
5.3.1 Assembling the bearing bushing, its raised thrust
block should fit into the locating groove in the cylinder
body.
Notice: The bearing bushing is from the same Oil Tank
manufacturer.
Spread Oil on the surface of

Bearing Bushing
5.3.2 Spread the crankshaft bearing bushing (upper
piece) with oil before assemble the crankshaft

Outer Forward of Oil

Tank

5.3.3 Mount the thrust plate on the cylinder body bearing

base and make sure that the side with oil gloove
(crankshaft shank) face outwards.
Notice: Spread the side of oil glove with oil
5.3.4 Fix the crankshaft bearing bushing (lower piece) in
the bearing cap, the bearing bushing should fit into the
thrust groove.

Forward Mark

5.3.5 Spread engine oil over the friction surface of

crankshaft bearing bushing (lower piece), assemble the
bushing according to the mark forwards in the main
bearing cap of the crankshaft.

Axle Diameter Mark

5.3.6 Spread oil over the bolts, within three or two times,
tighten them with specified torque.
Torque: 70±3.5N.m

5.3.7 Rotate the crankshaft after assembly, it should

rotates swiftly, the rotating torque should be less than
1Nm.

6-48
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

5.4 Assemble the piston and connecting rod assembly,

connecting rod bearing bushing and the connecting rod
bearing cap, pay attention to the following:
5.4.1 The opening of compression ring and the
opening of oil ring should be in the specified direction.
5.4.2 The bolts of the connecting rod should be
covered with nylon sleeves for fear of scraping the
cylinder body and the axle.
5.4.3 The surfaces of piston and connecting rod and
other surfaces where relative motion exists should be
spread with engine oil.

5.4.4 Confirm the mark forwards of the piston and

strike it into the cylinder body with the piston ring striking
tool.
Notice: The cylinder number of the piston and
connecting rod assembly should be in accordance with the
cylinder number.

5.4.5 Assemble the connecting rod bearing cap and the Forward Mark
connecting rod bushing, pay attention to the following:
5.4.5.1 Put the cover on the bolt as per the mark
forwards, spread a little engine oil over the joint surface
between the nut and its seat.
5.4.5.2 Tighten the right nut and the left nut alternatively
for several times with specified torque.

Torque: 40±2N.m
Notice: The connecting rod and the connecting rod
bushing should be of the same subassembly:

6-49
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 3. Table of Main Fit Clearance for SQR472 Engine SQR472

1 Clearance between Cylinder Hole and Piston Skirt (Piston to Cylinder Clearance)
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc

Group X: F720
0.005
Divided into two groups:
+0 . 01
Cylinder hole Clearance for group X:
φ72 0
Group S: F720.005
0.01
0.019mm～0.03mm
Clearance of group S:
-
0.015
Piston skirt φ72 -0.025 0.018mm～0.029mm

2 Clearance of Crankshaft Main Bearing

Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc
Crankshaft main journal φ42h6–0。016
0
Bearing bushing 2 - 0.006 Clearance 0.025~0.069
+
0.041
Bore of cylinder main bearing φ46F6 +0.025
3 Clearance of Crankshaft Connecting Rod Bearing
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc
Crankshaft connecting rod 0

journal φ37h6 -0.016

0
Bearing bushing 1.5 -0.006 Clearance 0.025~0.069

Bore of connecting rodbig +

0.041
end bearing φ40F6 +0.025
4 Clearance between Piston Pin and Piston Pin Hole
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc
Divided into twogroups Notice: When installed
+0.007
Piston Pin Hole φ18 +0.002 Clearance for group A: with hand, the piston pin
0.004 mm～0.0085mm； may pass through the
Clearance for group B: piston pin hole smoothly
0.0045mm～0.009 mm without any obvious
-
0.001
Piston pin φ18 -0.004 obstruction, otherwise the
piston pin should be
replaced.
5 Inteference between Piston and Small End of Connecting Rod
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc
Connecting rod small end -
0.026 Value of Interferenc
hole φ18 -0.044 0.021~0.043

6-50
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

-
0.001
Piston Pin φ18 -0.005

6 Fit Clearance between Connecting Rod Body Hole and Bolt Bar
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc

+
0.015 The hole should be processed along
Connecting rod body hole φ8.08 H7 0
Value of Interferenc with the connecting rod body.
0.008~0.032
+
0.032
Bolt Bar φ8.08 S6 +0.023

7 Fit Clearance between Connecting Rod Cover Hole and Bolt Bar
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc

+
0.015 The hole should be processed along
Connecting rod cover hole φ8.08 H7 0
Clearance with the connecting rod body.

-
0.005
0.005~0.029
Bolt bar φ8.08 f6 -0.014

8 Radial Clearance of Camshaft Bearing

Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc
0.021 1st bearing cap
Cylinder Head φ26H7 0
Clearance
-0.020 0.020~0.054 1st bearing cap
Camshaft φ26f6 -0.033
Intake
0.021 2nd, 3rd, 4th & 5th bearing caps
Cylinder Head φ23H7 0
Clearance
-0.020 0.020~0.054 2nd, 3rd, 4th & 5th bearing caps
Camshaft φ23f6 -0.033
0.021 1st bearing cap
Cylinder Head φ29H7 0
Clearance
-0.020 0.020~0.054 1st bearing cap
Camshaft φ29f6 -0.033
Exhaust
0.021 2nd, 3rd, 4th & 5th bearing caps
Cylinder Head φ23H7 0 Clearance
0.020~0.054
-0.020 2nd, 3rd, 4th & 5th bearing caps
Camshaft φ23f6 -0.033
9 Fit Clearance between Tappet Hole and Tappet
Name of Component Size and Tolerance Clearance or Value of Remark
Interferenc
0.021
Cylinder Head Hole φ28H7 0 Clearance
-
0.020 0.020~0.054
Tappet φ28f6 -0.033

6-51
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Remarks: In the above tables, the capital letter and suffix following the sizes (For example, H7 of φ28H7) mean the
process precision, which are unconcerned with the maintenance and may be ignored in the course of maintenance.

Chapter 4. Table of Measurement Parameters of SQR472

EngineSQR472

No. Measuring Items Acceptance value Remark

1 Axial clearance of crankshaft 0.089-0.211mm
Assemble the crankshaft and tighten the
main bearing cap bolt ≤1 Nm
Mount the piston connecting rod
Torque of crankshaft
assembly and tighten the connecting
when rotating at
rod bolt ≤5.5Nm
uniform speed
≤6Nm
2

Installing timing belt and spark plug

≤26 Nm
Mount the valve, spring and camshaft (excluding timing belt
and spark plug) on the cyllinder head, tighten the camshaft
bolt, and then measure the torque of the camshaft rotating at
uniform speed ≤32 Nm
Distance between the outer edge of steel ball and the front end
3 of camshaft 5.65±0.5mm
Distance between the outer edge of steel ball and the rear end
4 of camshaft 8.65±0.5mm
5 Axial clearance of intake camshaft 0.10~0.179
6 Axial clearance of exhaust camshaft 0.10~0.253
Jumping amount of installation surface of flywheel wearing
7 piece 0.10mmmax
8 Protrusion height of crankshaft woodruff key 2～2.20mm
9 Intake valve clearance 0.18±0.05mm
10 Exhaust valve clearance 0.25±0.05mm
Tension of timing belt (When the middle part of the rigth side
11 is pressed down for 4-5mm） 200～280N.m
12 Compression pressure of cylinder 10~14bar
Tension of generator belt （ When the part between the
13 generator and water pump is pressed down for 4-5mm） 98N.m
14 Refilling amount of engine oil (including filter) 3.5 Liter

6-52
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 5. Table of Main Fitting Torque for SQR472 EngineSQR472

No. Name Specification Quantity Fixing Torque (Nm) Remark

1 Main bearing cap bolt M10X1.25 10 70±3.5

2 Connecting rod cover bolt M8X1 8 40±2

3 Oil pump bolt M8X1 6 20±1.5

4 Nut (oil collector – oil ppump) M6 2 6±1

5 Bolt (oil collector – cylinder body) M6 1 6±1

6 Water pump bolt M8X1 6 25±1.5

7 Rear oil seal bracket bolt M8 5 25±1.5

8 Drain plug M12 1 45±3

9 Oil pan bolt M6 19 6±1

Bolt connecting exhaust camshaft with flange
10 M6 4 6±1
(hexagonal)
11 Exhaust camshaft locking nut M40X1.5(L) 1 100±5

12 Cylinder head bolt M10X1.25 10 70±3.5

13 Camshaft bearing cap bolt M6 19 9±1

14 Cylinder head chamber cover bolt M6 8 4.5±0.5

15 Camshaft position sensor bolt M8 1 10±1

16 Bolt (knock sensor) M8 1 20±1.5

17 Camshaft timing gear bolt M12X1.25 1 100±5

18 Tension pulley bolt M10 1 25±3

19 Timing cover bolt M6 7 6±1

20 Engine oil gauge pipe bolt M6 6±1

21 Flywheel assembly bolt M10X1.25 6 70±3.5

22 Thermoregulator shell bolt M8 2 10±1

23 Oil filter conncetor 3/4"-16 40±2.5

24 Oil filter 3/4"-16 20±1.5

6-53
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

25 Intake/exhaust stud M8 16 10±1 Spread glue

26 Intake pipe nut M8 8 25±1.5

27 Ignition coil bracket assembly bolt M8 2 20±1.5

28 Front lifting lug bolt M8 2 20±1.5

29 Exhaust pipe nut M8 8 25±1.5

30 Exhaust pipe thermal shroud bolt M6 3 6±1

Bolt on crankshaft pulley & torsional damper
31 M12X1.25 1 100±5
assembly
32 Water pump pulley bolt M6 4 6±1

33 Water temperature sensor M12X1.5 1 15±1.5

34 Oil pressure switch 1 30±2

35 Spark plug M14X1.25 4 20±1

36 Fixing Bolt of spark plug cover board) M6 8 2.5±0.5

37 Bolt (intake pipe front bracket) M8 1 20±1.5

38 Bolt (intake pipe rear bracket) M8 4 20±1.5

39 Bolt (throttle cable) M6 2 6±1

40 Bolt (gas-oil spearator bracket) M6 2 6±1

41 Bolt (throttle valve casing) M6 4 6±1

42 Oxygen sensor M18X1.5 1 40±2

43 Bolt (intake temperature & pressure sensor) M4 1 3±1

44 Fixing bolt of fuel guide rail M6 2 7±1

45 Ignition coil bolt M6 3 5±1

6-54
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 6. Positions on SQR472 Engine to be Lubricated

Type of lubricating oil: Engine lubricating oil

Designation of lubricating oil: SAE10W/30-50(SF Class)

No. Position to be lubricated Remark

1 Joint surface of connectong rod bolt head
2 Screw of connecting rod bolt
3 Exicrcle of piston pin
4 Inner wall of piston pin hole
5 Piston and piston ring
6 Inner wall of cylinder hole
7 Crankshaft main neck
8 Connecting rod shaft neck
9 Upper & lower main bearing bushing (inside)
10 Upper & lower connecting rod bearing bushing (inside)
11 Crankshaft thrust plate (the side of oil gloove)
12 Front oil seal and crankshaft front oil seal journal
13 Rear oil seal and crankshaft rear oil seal journal
14 Valve seat hole
15 Valve tappet and valve pipe hole
16 Excircle and hole of valve tappet
17 Camshaft journal and bearing base hole
18 Camshaft driving gear
19 Edge and excircle of oil seal
20 Oil seal journal and oil seal base hole
21 Surface oil filter sealing gasket

6-55
 Chery QQ Service Manual Mechanical Part of SQR 472Engine

Chapter 7. Positions on SQR472 Engine to be Spread with Sealant

SQR472

Position to be spread with Form and amount of

No. Type of sealant Remark
sealant sealant (reference)
1 Joingt surface of oil pan Loctite 5699 ф(3~4)mm

2 Rear oil seal bracket Loctite 5699 ф(3~4)mm

3 Valve chamber cover Loctite 5699 ф(3~4)mm

Joint surface if timing gear chamber Loctite 5699 ф(3~4)mm
4
cover
5 Joint surface of camshaft cover Loctite 5699 ф(3~4)mm
Sealing surface of the bowl shaped Loctite 11747 Spread uniformly
6
plug of cylinder head
7 Flywheel bolt Loctite 204 0.125(ml)×6 Pre-spread @3
Intake pipe stud Loctite 262 0.125(ml)×7 The part screwed into
8
the cylinder head
Exhaust pipe stud Loctite 262 0.125(ml)×6 The part screwed into
9
the cylinder head
10 Camshaft timing gear bolt Loctite 243 0.2ml
Oil collector stud Loctite 243 0.08(ml)×2 The part screwed into
11
the oil pump
Screw of thermoregulator shell Loctite 243 0.08(ml)×2 The part screwed into
12
fixing bolt the cylinder head

6-56
 7. FUEL INJECTOR SYSTEM

Overhaul Info…………………………………………………………………7-2
7
Fuel Injector System Disassembly/ Installation………………………………7-3

High Pressure Fuel Line Disassembly/ Installation…………………………7-4

Throttle Body Disassembly/Installation………………………………………7-4

Fuel rail with injector assy Disassembly/Installation…………………………7-5

Fuel injector Removal/Assembly………………………………………………7-5

7-1
 7. FUEL INJECTOR SYSTEM

Overhaul Info

CAUTION

NOTE
Gasoline is highly flammable, therefore smoke and fire are strictly forbidden in the work
place. Special attention should also be paid to sparks. Gasoline may also be explosive when it
is vaporized, so operation should be done in a well-ventilated place.
Do not over twist or bend the cables. The twisted cables may cause poor operation.
Loose the high pressure fuel line before disassembly, discharge the fuel in the high pressure fuel
line and put it in a container.
When the body of throttle valve is disassembled, the air intake shall be covered by dishcloth or tape,
for avoiding the entry of other objects into the engine from the air intake side of the engine.
When the vehicle will be stored for more than one month, the gasoline in the high pressure fuel line
and cap of the fuel injector must be discharged. Otherwise, the gasoline will age and form colloidal
elements which may block the nozzle of fuel injector, therefore the engine cannot start or the rotate
speed is unstable.

Overhaul Info
Engine Starting Failure Hard Starting/Stall After Starting, Unsteady
Too much fuel in the engine. Idle Speed
-Ail filter clogged. Idle air pipe clogged.
-Idle air pipe clogged. Fuel system clogged.
No fuel in the injector. Ignition system not functioning properly.
-Fuel filter clogged. Fuel tank cap clogged.
High pressure fuel line clogged.
-Fuel injector clogged.

7-2
 7. FUEL INJECTOR SYSTEM

Fuel Injector System Disassembly/ Installation

7

1. FUEL TANK 2. FUEL PUMP 3. “0”SEAL RING(ф6×ф100)

4. HOOP（φ120×2） 5. JOINT,FUEL HOSE 6. CLAMP（13-19）
7. FUEL HOSE (300mm) 8. BOLT,FLANGE（M8×16） 9. FUEL FILTER ASSY
10. FUEL HOSE (400mm) 11. PROTECTIVE SLEEVE, FUEL TANK CAP
12. CAP, FUEL TANK 13. SUPPORT, FUEL TANK(L) 14. BOLT,FLANGE（M6×12）
15. SUPPORT, FUEL TANK(R) 16. CLAMP（φ10） 17. LOCKNUT，FLANGE(M6)
18. INLET WINDPIPE (FRONT) 19. INLET WINDPIPE (MIDDLE)
20. RELAY, CARBON CANISTER 21. INLET WINDPIPE (RAER) 22. CARBON CANISTER
23. DEAD PLATE, CARBON CANISTER 24. RIVET (5×20)

7-3
 7. FUEL INJECTOR SYSTEM

High Pressure Fuel Line Disassembly

Loosen the special fuel line clamp on fuel injector cap.
loosen the special fuel line clamp on fuel tank.
Disassemble High pressure fuel line.

NOTE: Use container to keep the remaining fuel

from high pressure fuel line, when loosening
the special fuel line clamp.

High Pressure Fuel Line Installation

Reverse the disassembly procedure for installation.
Use clamp calliper to install the special fuel
line clamp.

Throttle Body Disassembly

Remove the connector of throttle valve opening sensor.
Remove the connector of idling solenoid valve sensor.
Loosen locknut, remove adjust nut and remove the
throttle cable from throttle rotory sleeve.
Loosen air filter clamp.
Remove intake tube of air filter.
Remove 2 clamps and remove circulating water hose.
Remove 4 bolts and remove throttle body.

NOTE: Do not adjust the bolt on throttle body.

Do not remove the cap on throttle body.

Throttle Body Installation

Reverse the disassembly procedure for installation.

7-4
 7. FUEL INJECTOR SYSTEM

Fuel rail with injector assy disassembly

7
Disassemble the special high pressure fuel
Remove the strap and fuel injector connector.
Disassemble 2 bolts and remove fuel rail with
injector assy.

Fuel rail with injector assy installation

Reverse the disassembly procedure for installation.

Fuel injector removal

Use Slotted screwdriver to remove snap spring.
Remove fuel injector from fuel rail with
injector assy.

Fuel injector assembly install

Install fuel injector into the fuel rail with
injector assembly.
Press the snap spring into groove of fuel
injector snap spring.

7-5
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Overhaul Info……………………..…8-1 Brake System…………………………8-4

Troubleshooting………………….…8-2 Suspension……………………………8-7
Front Wheel………………………...8-3 Steering………………………………8-12

Overhaul Information Operating cautions Notes

● Securely support the vehicle when overhauling the front wheel and suspension system.
● Refer to chapter10 for overhaul and inspection of lighting, instruments and switches.
● Do not overexert on the wheel. Avoid any damage to the wheel.
● When removing tire, use the special tire lever and rim protector.

Maintenance Standard

Item Standard Service Limit

Rim Longitudinal 0.8mm 2.0mm

Vibration Lateral 0.8mm 2.0mm
Remained groove － 3.0mm
Tire 12±0.5PSI(82.5±3.5KPa) －
Tire pressure
12±0.5PSI(82.5±3.5KPa) －
Front
Free play(brake lever) 0mm －
brake

Tightening Torque
Nut, Tie-rod 20-30 N·m

Lock nut, steering stem 20-30N·m

Nut, front wheel axle 180-200 N·m
Fixing bolt/nut, absorber（front） 30-40 N·m
Fixing bolt/nut, absorber（rear） 30-40 N·m
Nut, front/rear rim 40-50 N·m
Nut, rear wheel axle 180-200 N·m

8-1
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Troubleshooting Heavy
8
Steering Wheel Cannot Turn Freely
● Steering bearing is damaged or worn ● Faulty wheel bearing
● Inner & outer bearing races are damaged, ● Front wheel axle is bended
worn or stepped ● Brake drag
● Steering stem is distored ● Faulty steering structure
● Tire pressure is too low
Front Suspension is Too Soft
● Worn tire
● Weakened front shock absorbers
Shaking Steering Wheel
● Tire pressure is too low
● Steering wheel is not well tightened
Front Suspension is Too Hard
● Steering stem is loosened or not well installed
● Mount seat, steering wheel is not well tightened ● Front shock absorber is bended
● Bearing is damaged ● Tire pressure is too high
● Right and left shock absorbers are not matched Noise with Front Absorbers
● Deflected tires
● Faulty front shock absorbers
● Deformed frame
● Worn tiers ● Loosened tightening parts of front
● Shaking of wheel bearing absorbers
Vibration of Front Wheel Poor Brake Efficiency

● Wheel rim distorted ● Faulty brake adjustment

● Stained brake disc
● Faulty wheel bearing
● Worn brake shoes
● Faulty tire ● Air in brake hose
● Improper balance of wheels
● Improper tightening of wheel axle

8-2
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Front wheel

Removal
Securely support the front wheels Remove:
--Wheel cap
--4 bolts from wheel hub
--Front wheel

Inspection Rim
Damage, warpage or serious scrapes: →Replace
Replace with a new one, if any. Slowly turn the
wheel, measure the rim vibra-tion with a dial
gauge.

Service limit: Axial: 2.0mm

Radial: 2.0mm

Assembly:
Press rim into wheel
Install rim on the wheel hub
Tightening Torque: Bolt, Wheel Hub：40-50 N·m

Front Wheel Hub

Disassembly
Remove:
--Front wheel (→8-3)
--Front brake caliper (→8-4)
--Rim axle nut
--Brake disc and wheel hub
--4 bolts from front brake disc
--Wheel hub

Installation
Reverse the removal procedure for installation.
Torque, Rim axle nut: 180-200N· m

8-3
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Brake System
8
Front brake caliper
Removal
Remove:
--Front wheel（→8-3）
--2 bolts from arm
--Front caliper

Inspection
Check brake caliper for cracks and tightening
parts for oil leakage.
Replace if any.
Installation
Reverse the removal procedure for
installation.
Tightening Torque
Fixing Bolt, Brake Caliper: 45-50N· m.

8-4
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Brake Disc
Removal
Remove:
--Front wheel（→8-3）
--Brake caliper（→8-4）
--Front brake disc and wheel hub
--4 bolts from brake disc
--Brake disc

Inspection：
Brake disc thickness: <3mm →Replace

Installation
Install brake disc
Tightening Torque
Fixing bolt, brake disc：40-50N·m

Brake Master Cylinder Disassembly

Remove:
--Blot 1
--Cotter pin
-- Pin shaft.
Do not remove brake master cylinder from vehicle
unless when replacing master cylinder assembly.
Note:
Do not hang master cylinder on brake hose.
Do not put the master cylinder upside down to
avoid possible entrance of air into brake system.
Keep the master cylinder in the installation
position.
Proper routing of brake hose.
Check brake efficiency after installation.

8-5
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Brake Pedal Removal

Remove:
8
--Cotter pin
-- “E” clamp spring
-- Brake Pedal
Seperate Brake Pedal from vehicle
Disassembly of front brake master cylinder
（→ 8-5）
Installation
Reverse the removal procedure for installation.
NOTE
Do not put the master cylinder upside down to
avoid possible entrance of air into brake system.
Keep the master cylinder in the installation
position.
Refer to Chapter1 for proper routing of brake
hose.
Check brake efficiency after installation.

8-6
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Front Left Suspension

NOTE:
DO NOT
Remove both left and right suspension
at the same time to avoid fall down of
the vehicle.
Park the vehicle on a level ground and
securely support front part of the
vehicle.

Removal:
Remove:
--Front wheel(→8-3)
--Front wheel hub(→8-3)
--Front brake caliper(→8-4)
--Bolt1, Nut1.
--Shock absorber.

--Bolt2, Nut to Bolt2 for Front Left Arm (Upper)

--Bolt2, Nut to Bolt2 for Front Left Arm (Lower)

-- Remove steering tie-rod ball pin slot nut 3

-- Remove steering tie-rod.

Pull up joint knuckle from the driveshaft, remove

front left suspension assy.

8-7
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

1. COTTER PIN（3×25） 2. NUT(Rear wheel axle) 21. BOLT，FLANGE（M10×1.25×50）

3. FRONT WHEEL HUB 4. FRONT BRAKE DISC 22. LOCKNUT，FLANGE(M10×1.25) 8
5. BOLT( M10×25) 6. CIRCLIP (φ72) 23 . BOLT，FLANGE（M10×1.25×90）
7. BEARING 8. FRONT STEERING 24. BUSH ,ARM 25. CENTER SPACER
KNUCKLE(L) 9. FRONT STEERING KNUCKLE(R) 26. FRONT SHOCK ABSORBER
10. BOLT，FLANGE（M8×55） 27 . FRONT CV JOINT(L)
11. LOCKNUT，FLANGE(M8) 12. NUT（M10×1.25） 28. FRONT CV JOINT(R)
13. PIN, SPLIT（2.5×20） 14. CIRCLIP(φ32) 29. SUSPENSION PROTECTOR(L)
15. JOINT,ARM BALL 16. SCREW CAP，DRIVE 30. SUSPENSION PROTECTOR(R)
AXLETREE M12 17. PIN, SPLIT（3×30） 31. SCREW,TAP（ST4.2×20）
18. FRONT LOWER ARM 19. FRONT LEFT ARM

(UPPER) 20. FRONT RIGHT ARM (UPPER)

Disassembly
Disassembly
Front Left Shock Absorber
Disassembly
ATTENTION: You do not need to remove any other
parts if you only replace the front suspension.
Park the vehicle on a level ground,
Remove front left shock absorber’s bolt, nut installed
in arm.
Remove front left shock absorber.
Inspection
Inspect the shock for oil leakage, oil seal damage,
destroy, replace if needed.

8-8
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Installation
Reverse the removal procedure for installation.

Refer to front left shock absorber for removal,

installation and inspection of front right shock
absorber.

Arm Assembly
Attention: There are 8 suspension arms in the
vehicle, they dismantle, inspection and assemble
in the same way. So here only introduce the way
to dismantle, inspection and assemble the front
left upper arm and the front right lower arm.
Other arm assemble refers to the above.

Front Right Suspension

NOTE: Disassembly
Front Right Shock Absorber
DO NOT
Disassembly
Remove both left and right suspension
ATTENTION: You do not need to remove any
at the same time to avoid fall down of
other parts if you only replace the front
the vehicle.
suspension.
Park the vehicle on a level ground and
Park the vehicle on a level ground,
securely support front part of the
Remove front right shock absorber’s bolt, nut
vehicle.
installed in arm.
Removal: Remove front right shock absorber.
Remove: Inspection
--Front wheel(→8-3) Inspect the shock for oil leakage, oil seal damage,
--Front wheel hub(→8-3) destroy, replace if needed.
--Front brake caliper(→8-4)
--Bolt1, Nut1.
--Front Right Shock absorber.

--Bolt, Nut to Bolt for Front Right Arm (Upper)

--Bolt, Nut to Bolt for Front Right Arm (Lower)

-- Remove steering tie-rod ball pin slot nut

-- Remove steering tie-rod.

Pull up joint knuckle from the driveshaft, remove

front right suspension assy.

8-9
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Constant Velocity Drive Shaft

8
NOTE： The removal, inspection and installation
of Left and Right Constant Velocity Drive Shafts
of the Front/Rear Axles are the same. The
following will give instruction only on the removal,
inspection and inspection of Left Constant Velocity
Drive Shaft of Front Axle. Refer to Left Constant
Velocity Drive Shaft for removal, inspection and
installation of other drive shafts.
Left Constant Velocity Drive Shaft, Front Axle
Removal
NOTE: Maintenance of Left Constant Velocity
Drive Shaft of Front Axle only
does not require removal of Front
Suspension.
Remove:
--Front left wheel(→ 8-3)
--Front left brake caliper(→ 8-4)
--Front left wheel hub(→ 8-3)
Check dust boot.
Damaged dust boot: → Replace
Shake constant velocity drive shaft, check
the agility of rzeppa universal joint, free
turning of bearing, and any gap between rzeppa
constant velocity joint and spline.
Stagnated turning, noise, gap with spline:
→ Replace
Warning:
An accident may occur if the rzeppa
constant velocity joint cannot turn
freely because of the loss of control
of wheel steering.
Installation
Press ball pin into arm with special tool.
Reverse the removal procedure for installation.

Note: No shaking with the installed left

and right arms. Replace arms if any. Tightening
Torque：45～ 50N·m

8-10
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Steering System
Cover, Steering Stem
Removal
Remove cover, steering stem（→Chapter 2）

Combination Switch
Removal
Remove combination switch（→ 2-3）

8-11
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Rear View Mirror

8
Removal
Remove left and right rear view mirrors.
Note: Left rear view mirror is right-threaded.
Turn counter clockwise for
removal.

Note: Right rear view mirror is left-threaded.

Turn clockwise for removal.

8-12
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Steering Stem
Removal
Remove:
--Steering wheel（→ 2-2）

-- cover, steering stem（→ 2-2）

--Combination switch（→ 2-3）

--Bolt

--Shaft assy., steering joint

--Steering stem

8-13
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Installation of Combination Switch

Install combination switch（→ 2-11）
8

Insert main cable with connector of combination

switch.

8-14
 8 FRONT WHEEL, FRONT BRAKE，SUSPENSION，STEERING

Installation of Steering Wheel

Install steering wheel（→ 2-2）

Steering System

1. STEERING ASSY 2. LOCKNUT，FLANGE(M8) 3. BOLT，FLANGE（M8×16）

4. BOLT，FLANGE（M8×90） 5. STEERING SHAFT 6. BOLT，FLANGE（M8×25）
7. SPRING WASHER (Ф8) 8. BRACKET,STEERING STRENGTHENER
9. BOLT，FLANGE（M8×25） 10. STEERING STRENGTHENER 11. FLANGE,STEERING
STRENGTHENER 12. BEARING 13. BOLT,FLANGE(M8×30) 14. CIRCLIP(ф30)
15. OIL SEAL,STEERING STRENGTHENER 16. STEERING SHAFT(TOP)
17. GASKET(ф14×ф26×3) 18. SPACER BUSH (NYLON) 19. LOCKING NUT(M8)
20. SPACER BUSH (NYLON) 21. BOLT, STEERING COLUMN 22. LOCKING NUT(M6)
23. GAS SRPING,STEERING COLUMN 24. BOLT(M6) 25. STEERING COLUMN
26. SPRING WASHER 27. CORE SHAFT, STEERING 28. STEERING WHEEL ASSY
29. DECORATING COVER 30. BOLT (M5×15)

8-15
 9. REAR WHEEL 、REAR BRAKE 、SUSPENSION

Overhaul Info………………………………9-1 Rear brake………………………………9-4

Troubleshooting……………………………9-2 Rear suspension…………………………9-5 9
Rear wheel…………………………………9-3

Overhaul info:
Note:
● Securely support the vehicle when overhauling the rim and suspension system.
● Use genuine parts of bolts and nuts for rear rim and suspension.
● Do not overexert on the wheels to avoid possible damage to the wheels.
● When removing tire from rim, use special tire lever and rim protector to avoid
damage to the rim.

Overhaul standard

Item Standard Limit

Rim Longitudinal － 2.0mm
vibration Horizontal － 2.0mm
Tire Remained
－ 3.0mm
Rear Tire Tread
wheel Tire
12±0.5PSI(82.5±3.5KPa) －
pressure(front)
Tire
12±0.5PSI(82.5±3.5KPa) －
pressure(rear)
Rear
Brake pedal Free Play 0mm －
brake

Tightening torque

Rear wheel axle nut 180-200N.m

Rim mounting bolt 40-50N.m

Front mounting bolt, Shock absorber 30-40N.m

Rear mounting bolt, Shock absorber 30-40N.m

9–1
 9. REAR WHEEL 、REAR BRAKE 、SUSPENSION

Troubleshooting
Rear wheel wobbles
● Rim warpage
● Faulty tire.
● Tire pressure too low
● Improper wheel balance
● Improper tightening of wheel axle nut
● Loosened wheel nut

Rear shock absorber is too soft

● Weak spring.
● Oil leakage from rear shock absorber

Rear shock absorber is too hard.

● Bent rear shock absorber
● Tire pressure is too high

Poor brake efficiency

● Improper brake adjustment
● Stained brake pad or brake disk
● Worn or damaged brake pad

9–2
 9. REAR WHEEL 、REAR BRAKE 、SUSPENSION

Rear wheel removal:

Refer to front wheel remove.（→8-3）
9

Inspection Rim:
Damage, warpage, serious scrapes, etc. Replace if necessary.
Slowly turn the wheel, measure the rim vibration with a dial gauge.

Service limit：Axial: 2.0mm

Radial: 2.0mm

Installation:
Refer to front wheel installation.（→8-3）
Wheel hub removal:
Remove rear wheel (→9-3）
Remove brake caliper.
Remove mounting bolt, rim;
Remove wheel hub;

Installation:

Reverse the removal procedure for installation

Tightening torque, Rim Axle Nut：180-200N.m

9–3
 9. REAR WHEEL 、REAR BRAKE 、SUSPENSION

Rear Brake

Rear Brake Caliper

● Remove:
● Rear right wheel（→9-3）
● 2 bolts from arm
● Brake caliper
Inspection:

Brake Caliper:

Cracks, Oil leakage: → Replace

Installation

Reverse the removal procedure

for installation.
Note：

Refer to Chapter 1 for brake hose routing

Rear Brake Disc

Remove:
● Rear left wheel（→9-3）
● Remove mounting bolt, rim;

● Remove wheel hub;

● Rear brake caliper (→9-4)

● Rear brake disc（→8-3）
Inspection Brake Disc:
Thickness< 3mm: →Replace
Installation
Reverse the steps of removal for installation.
Note：
Refer to Chapter 1 for brake hose routing.
Parking caliper
Remove rear wheel（→9-3）
Loosen the bolt 1
Remove the parking cable.
Remove bolt 2.
Remove rear drive shaft.
Remove parking caliper.
Remove parking disc.

9–4
 9. REAR WHEEL 、REAR BRAKE 、SUSPENSION

Rear Suspension System

Rear Right Suspension
9
NOTE
DO NOT remove both left and right suspension at the same time to avoid fall down of the vehicle.

1. REAR STABILIZER BAR 2. RUBBER WASHER 3. HOLDER

4. BOLT,FLANGE(M8×20) 5. NUT（M10） 6. STABILIZER,CUSHION RUBBER
7. WASHER（φ11×φ30×2.8) 8. STABILIZER BOLT 9. BOLT，FLANGE（M10×1.25×50）
10. LOCKNUT，FLANGE(M10×1.25) 11. REAR SHOCK ABSORBER 12. BUSH ,ARM
13. CENTER SPACER 14. BOLT，FLANGE（M10×1.25×90） 15. REAR UPPER ARM ASSY
16. BOLT，FLANGE（M10×1.25×110） 17. BUSH, RR KNUCKLE（S） 18. BUSH, RR KNUCKLE（L）
19. REAR LEFT ARM（LOWER） 20. REAR RIGHT ARM（LOWER） 21. REAR STEERING KNUCKLE
22. BEARING 23. CIRCLIP(φ75) 24. BOLT，FLANGE（M10×25) 25. REAR BRAKE DISC
26. REAR WHEEL HUB 27. NUT 28. COTTER PIN（3×25） 29. BOLT，FLANGE（M10×1.25×135）
30. REAR CV JOINT(L) 31. REAR CV JOINT(R)

Disassembly
Stabilizer Bar
Remove:

9–5
 9. REAR WHEEL 、REAR BRAKE 、SUSPENSION

1. RUBBER WASHER (2); HOLDER (3) 3. BOLT, FLANGE M8×20 (4)

NUT (5); CUSHION RUBBER (6); WASHERφ11×φ30×2.8 (7); STABILIZER BOLT (8)
Remove Stabilizer Bar,
Installation:
Reverse the removal procedure for
installation
Right rear absorber

Removal:

Note: Securely support the vehicle when removing rear left and right absorbers.

Maintenance of rear absorbers only does not require removal of rear suspension.
Remove the following parts for rear right shock absorber：
(11) Bolt (9)
(12) Nut (10)
(11) Bolt (9)
(12) Nut (10)

Remove rear right shock absorber.

Installation:
Reverse the removal procedure for installation.

Rear Right Arm

Refer to front right Arm in Chapter 8 for the removal, inspection and installation of Rear Right
Arm

Rear Left Suspension

Refer to Rear Right Suspension for the removal, inspection and installation of Rear Left Suspension.

9–6
 10. FRONT/REAR AXLE

Front/Rear Axle Overhaul Information 10

z Standard
Lubricating Period
Replaced
Item Capacity
Initially Afterwards
Front Axle SAE15W/40 SF I:0.28L/R: 0.25L
or 350km 5000Km
Rear Axle SAE85W/90 GL-5 I:0.48L/R:0.45L
I= Initial, R=Replaced

Tightening Torque Table

Item Qty Type Torque(N.m) Remark
Fornt axle bolt 6 M8×1.25×25 20
Screw 2 M4×22 10
Screw 2 M5×15 10
Screw 1 M6×16 12
Screw 3 M6×25 13
Screw 1 M12×10 15
Front screw 1 M12×1.5 70 Glue
Bolt 6 M10×1.25×20 35
Front axle bolt 1 M18×1.25×8 20
Bolt 1 M10×1.25×12 25
Bearing Retainer 1 M65×2.0HL 60
Rear axle bolt 2 M10×20 30
Rear axle bolt 6 M8×40 25
Rear axle bolt 1 M8×20 25
Bolt 4 M6×10 15
Rear axle bolt 1 M6×16 15

10–1
 10. FRONT/REAR AXLE

Inspection & Overhaul

Inspection and overhaul if any of problems below happens to front and rear axle.
Descriptions Causes
1. Unstable moving during accelerating, A. Bearing broken;
decelerating or constant speed. B. Gear clearance over/under size;
C. Gear severely worn;
2. Abnormal sound in front rear axle; D. Gear blocked;
E. Drive shaft broken
3. Engine power transmission failure to front or F. lack of lubricant
rear wheels. G. Foreign matter in front or rear gear

Note：A、B、C problems are hard to distinguish. Analysis is needed based on actual break-down
catagories. Make sure engine works all right before disassembly of front or rear axle

Observation and Judgement

1. Never ignore abnormal sound:

a. Abnormal sounds during accelerating, decelerating have little to do with

engine working, but possibly with gear worn.

b. Constant abnormal sounds during accelerating or decelerating might be

cause by gear clearance wrongly adjusted during assembling.

Note: Wrong assembly or adjustment of the front or rear axle will aggravate

gear worn and block;

c. Slight sounds will be noticed during low-speed driving, and should not be heard during

high-speed driving. This is caused by gear block.

Note：In case of above mentioned times, stop the vehicle immediately for

inspection until they are solved, or will cause accident.

2. Check lubrication;

3. Check lubricant leakage;

a. Rear axle surface oil stain inspection before through inspection;

b. Oil stain on ground on the parking lot；

c. Lubricant splash inspection. Check if there is gear case or oil seal leakage.

Replace broken parts if necessary.

10–2
 10. FRONT/REAR AXLE

Disassembly of front axle

10
1. FRONT AXLE HOUSING GROUP

Ref.N Description QTY Ref.No Description QTY

o
1 FRONT AXLE LEFT CASE 1 11 OIL SEAL (45×68×8) 1
2 OIL SEAL (25×40×7) 1 12 FRONT AXLE RIGHT CASE 1
3 O-RING (ф16.5×ф2.5) 1 13 BEARING (16007) 1
4 BOLT(M18×1.5×10) 1 14 CIRCLIP(62) 1
5 O-RING(ф15.5×ф1.5) 1 15 O-RING(ф160×ф3) 1
6 SPEED SENSOR 1 16 ALUNINUM PAD(ф18×ф10×1.5) 1
7 BOLT,FLANGE(M6×16) 1 17 BOLT,FLANGE(M10×1.25×12) 1
8 ALUNINUM PAD(ф18×ф10×1.5) 1 18 OIL SEAL(25×40×7) 1
9 JOINT, BREATHER PIPE 1 19 BOLT,FLANGE(M8×1.25×25) 6
（M10×1.25×10）
10 NEEDLE BEARING(NA5903) 1

10–3
 10. FRONT/REAR AXLE

2. TWO-FOUR-DRIVE CONVERSION MECHANISM FOR GROUP

Ref.No Description QTY Ref.No Description QTY

1 GEAR MOTOR 1 9 WASHER(φ8×ф4×1) 3
2 RING 1 10 SPRING PAD 4 3
3 DOWEL PIN(φ8×10) 2 11 HEX NUT 3
4 BOLT,FLANGE(M6×25) 3 12 CONTACT COVER 1
5 CONNTACT COMPONENTS 1 13 WASHER(φ8×ф4×1) 2
6 GASKET 1 14 SPRING PAD 2
7 SCREW 2 15 SCREW(M4×22) 2
8 CONTACT WIRE 1 16 DIFFERENTIAL CONTROLLER 1

3. FRONT AXLE HOUSING GROUP

Ref.No Description QTY Ref.No Description QTY

1 DRIVEN BEVEL GEAR FRONT 1 6 BEARING RETAINER（M65×2.0HL） 1
ASLE（LEVOROTARY/Z=33）
2 BEARING（6008/P6） 1 7 COUPLER（14T） 1

3 ADJUST WASHER B （ φ 54× ф 1 8 WASHER（φ12×ф30×4） 1

66×0.2）
4 DRIVE PINION GEAR （ DEXTRAL 1 9 NUT FLANGE（M12×1.25） 1
/9T）
5 BEARING（TM6305） 1

10–4
 10. FRONT/REAR AXLE

4. REAR AXLE HOUSING GROUP

10

Ref.No Description QTY Ref.No Description QTY

1 GEAR MOTOR ASSEMBLY 1 9 WASHER 1

2 BOLT M8*40 4 10 BEARING 6010 1

3 SPRING WASHER φ8.5-2.5 4 11 ADJUST WASHER 1

4 DRIVE GEAR ASSEMBLY 1 12 DIFFERENTIAL GEAR 1

ASSEMBLY

5 BEARING NA2512 1 13 DIFFERENTIAL GEAR CASE 1

6 OIL SEAL 35*55*8 1 14 SPRING WASHER φ8.5-2.5 8

7 FRONT DIFFERENTIAL GEAR 1 15 BOLT M8*40 8

CASE COVER

8 DRAIN BOLT M10*20 1 16

10–5
 10. FRONT/REAR AXLE

5. REAR AXLE HOUSING GROUP

Ref.No Description QTY Ref.No Description QTY

1 DRIVEN GEAR 1 9 BOLT M8*1*20 12
2 SUPPORT，DIFFERENTIAL GEAR, R 1 10 ADJUST WASHER 1
3 BUSH 1 11 GEAR,SHAFT SET, R 1
4 ADJUST WASHER 1 12 PLANET GEAR SHAFT 1 1
5 GEAR,SHAFT SET, R 1 13 PLANET GEAR SHAFT 2 1
6 RETAINER φ35 2 14 PLANET GEAR 4
7 LINK GEAR 1 15 SPHERE WASHER 4
8 SUPPORT，DIFFERENTIAL GEAR, L 1 16 RETAINER WASHER 6

6. REAR AXLE HOUSING GROUP

Ref.No Description QTY Ref.No Description QTY

1 DRIVE GEAR 1 3 RETAINER φ35 1
2 BEARING 6307 1 4 RETAINER φ35 1

10–6
 10. FRONT/REAR AXLE

7. REAR AXLE HOUSING GROUP

10

Ref.No Description QTY Ref.No Description QTY

1 FRONT DIFFERENTIAL GEAR CASE 1 11 RETAINER φ10 1
2 OIL SEAL 10*22*7 1 12 SPRING 1
3 OIL SEAL 35*55*8 1 13 RETAINER φ10 1
4 WASHERΦ6*1 1 14 SPRING 1
5 BOLT M6*10 1 15 RETAINER GUIDE BAR 1
6 WASHER 1 16 BOLT M6*16 2
7 STOPPER 1 17 RETAINER SHIFT FORK 1
8 EXHAUST VALVE 1 18 INNER COVER 1
9 BEARING 61912 1 19 RETAINER 1
10 SHAFT φ5*20 1 20 O-RING 160*2.65 1

10–7
 10. FRONT/REAR AXLE

Inspection after front axle disassembly

z Check if there is damage or crack on the front differential gear case cover and bearing assembling
hole is ok. Replace case cover if necessary;

z Check if front axle bearing clearance ok or turning stable, and roll way, steel ball, needle and plate
are ok. Replace bearing if necessary.(Using special tools)

z Check if oil seal lips and O-ring shape are ok. Replace if necessary;

z Check cylndrical surface of front axle and oil seal lips. Replace broken parts if necessary;

z Check drive pinion gear and differential gear, inspect worn surface. Replace broken if necessary;

z Check driven gears surface, gear(center)differential, bracket differential wearing situation on the
differential gear assembly. Replace parts if necessary;

z Check inside and outside spline washer wearing status in front axle. Replace parts if necessary;

z Check gear motor working status. Replace with new parts if necessary;

Gear motor inspection must be carried out with special equipment or acted on the vehicle;
z Check other parts. Replace broken parts of necessary.

10–8
 10. FRONT/REAR AXLE

Front axle assembly and adjustment

10
z Front axle case cover assembly

Item“31”tightening torque60Nm

Item“24”tightening torque70Nm

Note：Use engine oil for oil seal,

bearing and drive clutch assembly;

“ 24” Use screw thread fastening glue;

z Front differential gear case cover

assembly;

Note: Use engine oil for oil seal or

bearing assembly.

z Differential gear assembly

M10×1.25×20,Tightening torque35Nm

Note ： Use engine for bearing and dif-

ferential gear;；

Use proper washer to make gear working

freely.

Adjust washer 0.2 0.3 0.4 0.5

thickness 1.0

10–9
 10. FRONT/REAR AXLE

z Front axle assembly and adjustment

Illustration：

Tightening torque

Item“ 1” 25Nm
Item“25” 10Nm
Item“30” 13Nm

Use fastening glue for item“30” assembly.

a. Use proper washer 8 and 10 thick ness to adjust

gear side clearance between drive pinion gear

and differential gear.

Drive bevel gear clearance measurement; Install sup-

port tools, tightening bolts(M10 ×1.25 ) put up
dial indicator, make sure 21 mm is between measuring
point and support tools. Turn support tools counter-
clock and read the data.
Standard: 0.10-0.25
Adjust washer 0.1 0.2 0.3 0.4
thickness 0.5 1.0

b. Shift fork and drive clutch assembly should be

against tightly to the arrow shape illustration.

10–10
 10. FRONT/REAR AXLE

c. Use special equipment or vehicle control

circuit into two stroke position(M6×25)
10
before gear motor assembly;

d. Make sure b and c is assembled using illustrated

positioning bolt before gear motor and front axle.

10–11
 10. FRONT/REAR AXLE

Needle bearing removal

a. Disassemble needle bearing 55BTM6820
as illustration if necessary.

b. Disassemble needle bearing NA5903

as illustration after heating up to
150℃ .

Rear axle inspection after disassembly

z Check if there is crack or damage in rear gear case, see mounting hole is ok . Replace gear case or

right cover if necessary;

z Check if bearing clearance is normal, and turning stability, rollway, stell ball, neddle bearing as

well. Replace bearing if necessary.(Special tools are required)

z Check rear axle if bearing clearance is normal, turning status rollway, stell ball, neddle bearing as

well. Replace bearing if necessary.(Special tools are required)

z Check worn status of drive bevel gear and ring gear rear axle. Replace if necessary;

z Check oil seal lips, o-ring shape. Replace parts if necessary;

z Check cylndrical surface of rear axle and oil seal lips. Replace if necessary;

z Check inner and outsider spline. Replace if necessary;

z Check other parts. Replace if necessary.

10–12
 11. EFI SYSTEM OF SQR 472ENGINE

Foreword
11
The 472 engine is a cylinder increase in R & D base 372 engine, to meet the more large capacity
and power requirements. On the structure and technical characteristics of the engine, and it is the
same as the 372 engine. So, everybody through this repair manual understanding, should be able to
quickly grasp the essentials of the 472 engine repair.

In order to help the technical service personnel to understand and familiar with Chery QQ
SQR7110 models, has the capability of rapid repair and maintenance, specially written "Chery QQ
Technology Service Manual - 472 engine mechanical part".

This manual details the disassembly, inspection, testing and diagnosis technology standard
Chery QQ472 engine components or systems. This manual is provided by Chery Engine Co. Ltd.

The license without written authorization, any part of the book can not be in any form or by any
means to copy or use.

This manual interpretation of Chery Motor Sales Company Sales Service Department。

The editor
August 2008
（First edition.）
 11. EFI SYSTEM OF SQR 472ENGINE

CONTENTS
Chapter 1 Description the SIMK-31 engine management system................................................1
Summary.........................................................................................................................................1
A、 The basic components of electronic control system.......................................................................1
B、 The SIMK-31ECU module input and output electrical diagram......................................................1
1、The input and output SIMK-31ECU module..............................................................................1
2、Engine management system diagram.....................................................................................2
3、Wiring diagram of ECU............................................................................................................3
4、ECU function module layout....................................................................................................4
5、Pin output definition ECU.........................................................................................................5
Chapter 2 The working principle of engine management system components............................. ......7
1, the water temperature sensor...........................................................................................................7
2, the crankshaft position sensor..........................................................................................................9
3, the camshaft position sensor...........................................................................................................11
4, the throttle body...............................................................................................................................13
5, solar term door position sensor.......................................................................................................15
6, idle speed control motor..................................................................................................................15
7, heated oxygen sensor.....................................................................................................................17
8, the intake air temperature and absolute pressure sensor...............................................................20
9, the fuel rail assembly.......................................................................................................................22
10, the fuel injector...............................................................................................................................23
11, carbon canister solenoid valve.......................................................................................................26
12, the engine control unit (ECU).........................................................................................................28
13, electric fuel pump...........................................................................................................................30
14, the ignition coil...............................................................................................................................32
15, three way catalytic converter..........................................................................................................33
16, the other is connected with ECU signal..........................................................................................33
Chapter 3 Introduces the function of fault diagnosis system..................................................... ............34
1, control the fault lamp........................................................................................................................34
2, Connect the diagnosis instrument....................................................................................................34
3, Fault code list...................................................................................................................................35
4, Erase fault code...............................................................................................................................37
Chapter 4 Troubleshooting diagnostic process........................................................................ ...........38
1, Fault diagnosis according to the fault code description....................................................................38
2, System fault code diagnosis process...............................................................................................38
2.1、Upstream oxygen sensor heater control circuit shorted to ground (fault code P0031) ................38
2.2、Upstream oxygen sensor heater control circuit for the power supply circuit (fault code P0032) ..39
2.3、The lower the oxygen sensor heater control circuit shorted to ground (fault code P0037) ...........39
2.4、Downstream oxygen sensor heater control circuit for the power supply circuit (fault code
P0038) .................................................................................................................................................40
2.5、Manifold pressure sensor circuit shorted to ground (fault code P0107) ......................................40
2.6、Manifold pressure sensor circuit for the power supply circuit (fault code P0108) .......................41
2.7、Intake air temperature sensor circuit shorted to ground (fault code P0112) ...............................41
2.8、Intake air temperature sensor circuit for the power supply circuit (fault code P0113) .................42
2.9、Coolant temperature sensor circuit output range / character error (error code P0116) ................43
 11. EFI SYSTEM OF SQR 472ENGINE

2.10、Coolant temperature sensor circuit shorted to ground (fault code P0117) ...................................44
2.11、Coolant temperature sensor circuit for the power supply circuit (fault code P0118) ...................44 11
2.12、Coolant temperature sensor circuit discontinuity (fault code P0119) ........................................45
2.13、Solar term door position sensor circuit shorted to ground (fault code P0122) ..........................45
2.14、Solar term door position sensor circuit for the power supply circuit (fault code P0123) ...........46
2.15、Oxygen sensor circuit fault (fault code P0130) .........................................................................46
2.16、Oxygen sensor circuit output voltage is too low (fault code P0131) .........................................47
2.17、Oxygen sensor circuit output voltage is too high (fault code P0132) .......................................47
2.18、The oxygen sensor is not active (error code: P0134) ..............................................................48
2.19、Oxygen sensor circuit fault (fault code P0136) .........................................................................48
2.20、Oxygen sensor circuit output voltage is too low (fault code P0137) .........................................49
2.21、Oxygen sensor circuit output voltage is too high (fault code P0138) ........................................49
2.22、The oxygen sensor is not active (fault code P0140) .................................................................50
2.23、Pump primary line fault (fault code P0230) ...............................................................................50
2.24、A cylinder injector circuit shorted to ground (fault code P0261) ................................................51
2.25、A cylinder injector circuit for the power supply circuit (fault code P0262) ..................................52
2.26、Two cylinder injector circuit shorted to ground (fault code P0264) ...............................................52
2.27、Two cylinder injector circuit for the power supply circuit (fault code P0265) .............................53
2.28、Three cylinder injector circuit shorted to ground (fault code P0267) ........................................53
2.29、Three cylinder injector circuit for the power supply circuit (fault code P0268) ..........................54
2.30、Four cylinder injector circuit shorted to ground (fault code P0270) ...........................................55
2.31、Four cylinder injector circuit for the power supply circuit (fault code P0271) ............................55
2.32、Knock sensor fault (fault code P0325) ......................................................................................56
2.33、Crankshaft position sensor circuit fault (fault code P0335) .......................................................56
2.34、The camshaft position sensor fault (fault code P0340) ............................................................56
2.35、A cylinder ignition coil circuit fault (fault code P0351) ..............................................................57
2.36、Two cylinder ignition coil circuit fault (fault code P0352) ..........................................................57
2.37、Three cylinder ignition coil circuit fault (fault code P0353) ......................................................58
2.38、Four cylinder ignition coil circuit fault (fault code P0354) ........................................................58
2.39、Carbon irrigation control valve (open circuit fault code P0444) ................................................59
2.40、Carbon irrigation control valve (short circuit fault code P0445) ................................................59
2.41、The speed sensor is not working properly (fault code P0501) .................................................60
2.42、Idle stepper motor fault (fault code P0505) ..............................................................................61
2.43、The system voltage fault (fault code P0560) .............................................................................61
2.44、Internal control module (read-only memory) fault (fault code P0605) .......................................62
2.45、Malfunction indicator lamp control circuit fault (fault code P0650) ............................................62
2.46、Air conditioner evaporator temperature sensor for short circuit or open circuit (power line fault
codeP1535) ..........................................................................................................................................63
2.47、Short circuit of the air conditioning evaporator temperature sensor circuit (fault code
P1536) .................................................................................................................................................63
2.48、Air pressure switch or air conditioning clutch relay line fault (fault code P1545) ......................64
2.49、Cooling fan relay line fault (fault code P1624) ..........................................................................65
2.50、Fan relay or fan line fault (fault code P1625) air conditioning compressor................................65
3、For fault diagnosis according to the fault phenomena.......................................................................66
 3.1、Start engine does not rotate or move slowly................................................................................66
3.2、When starting the engine can be dragged to but failed to start...................................................67
3.3、Difficulty in starting the car...........................................................................................................68
3.4、Difficult cold start.........................................................................................................................69
3.5、The normal speed, any time starting difficulty............................................................................70
3.6、Start normal, but any time idling instability.................................................................................71
3.7、Normal starting, warm process of unstable idle speed...............................................................72
3.8、Normal starting, warm after the end of unstable idle speed........................................................73
3.9、Normal starting, part load (such as: air conditioning) when idling instability or flameout............74
3.10、Normal starting, idle speed is too high......................................................................................75
3.11、To accelerate the speed to go up not to go or stop..................................................................77
3.12、Acceleration response is slow...................................................................................................78
3.13、Acceleration of weakness, poor performance..........................................................................79
 11. EFI SYSTEM OF SQR 472ENGINE

Chapter 1 Describes the SIMK-31 engine management system

11
一、 Overview
The engine management system mainly consists of sensors, microprocessors (ECU), executive
device is composed of three parts, the inhalation of air traffic control, fuel injection and ignition
advance angle of the engine work.

In the engine electronic control system, sensor as input part, for a variety of physical
measurements (temperature, pressure), and turn it into a corresponding electrical signal; the role
of ECU is to accept input signal sensor, processing and calculation according to the program, to
generate a control signal output corresponding to the power drive circuit, power driving circuit is
driven by the actuator perform different actions, make the engine run in accordance with the
established control strategy; at the same time, fault diagnosis system of ECU for each component
or control functions of the system for monitoring, once detected faults and confirmation, the
memory fault code, call "limp home" function, when the detected fault is eliminate, then normal
recovery using.

二、The basic components of electronic control system

The electronic controller (ECU) Injector Crank position sensor
Oil rail Camshaft position sensor Carbon canister control valve
Intake manifold Oxygen sensor Temperature sensor
Three way catalytic converter Inlet pressure / temperature sensor
Ignition coil and the high-voltage wire
Idle speed regulator Oil pump assembly Solar term door position sensor
Solar term door assembly Knock sensor Temperature sensor

三、The SIMK-31ECU module input and output electrical diagram

1、Input and output module, SIMK-31ECU.

The main sensor input signal in SIMK-31 system of ECU include:
Inlet air pressure signal
Intake air temperature signals
Solar term door position signal
Coolant temperature signal
Crank angle signal
The camshaft phase signal
Oxygen sensor signal
Air conditioning request signal
Air pressure signal
Air conditioner evaporator temperature

11-1
 11. EFI SYSTEM OF SQR 472ENGINE

Speed signal
Knock signal
The above information into the ECU after the treatment the actuator control signal needed, these
signals are driven by amplifying circuit at the output, and transmitted to the corresponding
actuator control signal, which includes:
Idle speed regulator opening
Fuel injection timing and injection duration
Ignition coil closed angle and ignition advance angle
The carbon canister control valve opening
Oxygen sensor heater heating control
Main relay
Pump relay control
The air conditioning compressor control relay
Air conditioning cooling fan relay control
Cooling fan relay
Trouble light control

2、The engine management system management system diagram

11-2
 11. EFI SYSTEM OF SQR 472ENGINE
3、The ECU control principle diagram

11-3
 11. EFI SYSTEM OF SQR 472ENGINE
4、 The ECU function module layout.

11-4
 11. EFI SYSTEM OF SQR 472ENGINE
5、Pin output definition ECU
Pin Connection point / description Type Pin Connection point / description Type 11
1 The power of 1 Earth 42 Oxygen sensors downstream signal Input
2 The power of 2 Earth 43 Upstream oxygen sensor signal Input
3 Empty 44 Battery power supply 1 Input
4 Ignition signal 1 Output 45 Solar term door position sensor supply Input
5 Ignition signal 2 Output 46 The intake pressure sensor supply Input
6 CAN low Input / output 47 Empty
7 CAN high Input / output 48 Inlet pressure and temperature sensor. Earth
8 Upstream oxygen sensor heater Output 49 Empty
9 The lower the oxygen sensor heater Output 50 Air pressure switch signal Input
10 Knock signal Input 51 The headlight switch Input
11 Empty 52 Empty
12 The evaporator temperature signal Input 53 Empty
13 The evaporator temperature signal Earth 54 Knock sensor Earth
14 Empty 55 Ignition shielding. Earth
15 Empty 56 Intake air temperature signals Input
16 Empty 57 Empty
17 Empty 58 Air conditioning request signal Input
18 Empty 59 Upstream oxygen sensor Earth
19 Stepper motor coil A+ Output 60 Inlet air pressure signal Input
20 Stepper motor coil A- Output 61 2 cylinder injection signal Output
21 The main relay power Input 62 4 cylinder injection signal Output
22 After the ignition is switched power supply Input 63 Battery power supply 2 Input
23 The 3 cylinder output Output 64 Cooling fan relay (high speed) Output
24 The 1 cylinder output Output 65 Cooling fan relay(low speed)
25 Empty 66 Engine speed signal output Output
26 The carbon canister control valve control Output 67 Main relay Output
signal
27 Crankshaft signal Earth 68 The air conditioning compressor relay Output
28 Empty 69 Fuel pump relay Output
29 Crankshaft signal input Input 70 Fault indicator Output
30 Camshaft signal Earth 71 Empty
31 The cooling water temperature signal Input 72 The camshaft position signal Input
32 Solar term door position signal Input 73 Coolant temperature sensor Earth
33 Empty 74 Power steering signal Earth
34 Empty 75 Empty
35 Stepper motor coil B+ Output 76 Empty
36 Stepper motor coil B- Output 77 Diagnosis of the K Input / output

37 The lower the oxygen sensor signal Earth 78 Empty

38 Solar term door position signal Earth 79 Empty

11-5
 11. EFI SYSTEM OF SQR 472ENGINE
39 The speed signal input Input 80 Empty
40 Empty 81 Empty
41 Empty

11-6
 11. EFI SYSTEM OF SQR 472ENGINE
Chapter 2 The working principle of engine management system

1、Water temperature sensor

components 11
1) Diagram and pin

2) Installation position
Installed in the cooling water flow rate is high, and can correctly reflect the engine cooling water
temperature, such as the water outlet of the engine or the engine cooling system circuit.
3) Working principle
The two NTC thermistor is encapsulated in the temperature sensor, the resistance value varies with
the temperature of the cooling water, cooling water temperature is low, the resistance of the
thermistor is large. The cooling water temperature is high, the resistance of the thermistor is smaller.
Conversion of resistance into the change of voltage input to the ECU, ECU according to the
temperature of cooling water, the basic injection time, carries on the revision to the idle speed and
the air volume. On the other hand, it also output signals to the instrument, the driving staff can
directly by visually judge the operating state of engine.
As shown in Figure 6 structure temperature sensor

11-7
 11. EFI SYSTEM OF SQR 472ENGINE
4) Technical parameters
The water temperature sensor contains two thermistor, a dedicated water temperature signal input pin ECU, use A,
C, a water temperature sensor and instrumentation for temperature signal input pin, used for B and shell as earth.
Limit data
measure A, C value B, value unit
Rated voltage Run with ECU (5V)
Nominal resistance at 25 ℃ 1.825 to 2.155 KΩ
Operating temperature range -30 至+130 ℃
The maximum current sensor 1 mA
Vibration acceleration license 600 m/s
(2) Characteristic data
number Temperature (c)
A, C end temperature tolerance of B junction temperature tolerance
± 0.1 ℃ (resistance (Ω)) of ± 0.1 ℃ (resistance (Ω))
Least The maximum Least The maximum
1 13.71 16.49 -20
2 1.825 2.155 +25
3 0.303 0.326 63.4 81.4 +80
5) Installation notes
The sensor should apply sealant in the installation process, suggestions on the selection of conductive sealant.
Sealant should be applied in the graphic (Figure 7) plane, should ensure that adequate smear that sealant after
tightening anhydrous leakage phenomenon; pay attention to installation thread does not allow fluid sealant, to
ensure that the assembly and disassembly and good conductivity sensor.

In the installation process of tightening, tighten six angle plane using spanner copper sleeve. May not be a
plastic parts are tightened, so as not to damage the product. Maximum tightening torque: 20N.m.
6) the malfunction phenomenon and the judgment method
General failure
1. The starting difficulty
A simple method for testing: (unloading joints) digital multimeter to Ohm, two probes are respectively
connected sensor A#, C# pin, 25℃ rated 1.825~2.155K resistors. Measurement can also be used when the
simulation method, in particular to the sensor working area and dropped into the boiling water (note the
immersion time to fully), observe the change of the sensor resistance, the resistor should decline to 300 Ω
(specific value as the temperature of boiling water).
2. The water temperature indicating meter failure
Simple test method:
(unloading joints) digital multimeter to Ohm, two probes are respectively connected sensor B# pin and the
copper shell, using the simulation method, in particular to the sensor working area and dropped into the boiling
water (note the immersion time to fully), observe the change of the sensor resistance, the resistor should decline
to 60 Ω (the specific value as the temperature of boiling water).
11-8
 11. EFI SYSTEM OF SQR 472ENGINE
2. The crankshaft position sensor
1) Diagram and pin
11

2) Installation position
The back of the engine flywheel plane.
3) Working principle
Holzer type crankshaft position sensor with the target wheel is matched, provide check point information of
engine speed and the cylinder piston. Holzer type crankshaft position sensor integrated dynamic permanent
magnet biased differential pair of Holzer IC. When the target wheel in front of regional rotation sensor sensitive
IC detection, due to the lack of teeth and tooth alternation is produced by the variation of the magnetic field and
the Schmidt trigger conversion by square wave signal.
4) technical parameters
(1) limit data
measure be worth units
Least Typical The maximum
Hall type crankshaft The launch area -40 150 ℃
position sensor can Conductor area -40 150 ℃
withstand Storage temperature -40 150 ℃
temperatures Don't run when the environment -40 120 ℃
temperature
Long-term environmental temperature -40 120 ℃
during operation
The launch 750 Special Ops 150 ℃
area's entire 1500 Special Ops 140 ℃
service life
3000 Special Ops 130 ℃
Wire area as 150 ℃
a whole
lifetime
Insulation resistance (2min test voltage Moh
500VDC) m
Pressure (60s, 250V) No breakdown

11-9
 11. EFI SYSTEM OF SQR 472ENGINE
(2) Characteristic data

measure value unit

least maximum
The phase accuracy +0.45 -0.45 。
The air gap 0.3 1.7 mm
The target wheel speed 15 8000 rpm
Supply voltage 6 16 V

5) Installation notes
The sensor is only allowed in the soon to be installed prior to the car or to the test device to
remove from packaging materials.
Sensor installation direction specified as shown below.

Installation method of sensor by indentation instead of hammering. Recommended bolt fixed sensor
M6.Tightening torque of 8 2Nm.
Holzer type crankshaft position sensor and signal disc tooth tip of the air gap between nominal
value is: 1.0mm; allow the range is 0.3 to 1.7mm.
6) The malfunction phenomenon and the judgment method
Fault phenomenon: not starting.
General failure: man-made fault.
Note: repair installation method of repair process by pressing instead of hammering.
A simple method to measure:
(thenthefragmentswereligatedwithan adapter) open the ignition switch but do not start the engine,
the digital multimeter to DC voltage, two probes are respectively connected sensor 1#, 3# pin, to
ensure that the reference voltage 12V. Start the engine, the 2# pin signal by the automotive
oscilloscope check whether it is normal.

11-10
 11. EFI SYSTEM OF SQR 472ENGINE
3, The camshaft position sensor
1) Diagram and pin
11

2) Installation position
Camshaft end cover.
3) Working principle
The sensor makes use of the magnetic induction intensity changes by Holzer Holzer in the
principle of voltage made into.

11-11
 11. EFI SYSTEM OF SQR 472ENGINE
4) Technical parameters
Limit data
measure Value unit
Least Typical The maximum
The sensor Storage temperature -40 +150 ℃
can Don't run when the -40 +120 ℃
withstand environment temperature
temperature Long-term environmental -40 +120 ℃
temperature during operation
The whole 200hour -40 ℃ ℃
lifetime 1000hour +140 ℃
20X0.5hour ℃
155
Insulation 15 Mohn
resistance (2min test voltage 500VDC)
（2）Characteristic data
measure value unit
least maximum
Ambient temperature -30 +120 ℃
Install air gap 0.3 2 mm
Supply voltage 4.5 24 V

Relative accuracy 6 6
The target wheel speed 0 4000 rpm
5) Installation notes
Installation method of sensor by indentation instead of hammering.
Recommended bolt fixed sensor M8. Tightening torque 10~14Nm.
The air gap between the camshaft position sensor and signal wheel: allows the range is 0.3 to
2.0mm; the Holzer elements working diagram (two).
6) fault phenomenon and judgment method
Fault phenomenon: emissions exceed the standard, increased fuel consumption.
General failure: man-made fault.
A simple method to measure:
(thenthefragmentswereligatedwithan adapter) open the ignition switch but do not start the engine,
the digital multimeter to DC voltage, two probes are respectively connected sensor 3#, 2# pin, to
ensure that the reference voltage 12V. Start the engine, the 1# pin signal by the automotive
oscilloscope check whether it is normal.

11-12
 11. EFI SYSTEM OF SQR 472ENGINE
4. The throttle body

11

Throttle valve control intake air into the engine cylinder, so as to control the engine speed and load.
The festival Flow valve is composed of two channels, namely a main channel and side channel.
Solar term door pedal through the throttle cable control main channel opening, gas flow throttling
into a cylinder of the engine; solar term door opening by the solar term door position sensor is
transmitted to the engine control unit ECU.
Installation notes
(1) the throttle body and the intake hose connection must be sealed, to prevent dust entering the
throttle body blocked the inlet channel.
(2) the throttle body and the intake manifold must seal pad, and fastening and loosening leakage.
Every time after disassembling the throttle body, need to replace the gasket new.
(3) coloring screw throttle body from the demolition, to prevent the destruction of the initial
setting.
(4) the vehicles running on certain mileage, such as twenty thousand kilometers (the large dust,
reduce it) or solar term valve plate dust deposition is large, the throttle valve of main channel
and side channel cleaning, cleaning agent is not conductive to the throttle body is cleaned, dried,
check with a multimeter solar term door position sensor and idle speed step motor is correct,
can be loaded back.
5, solar term door position sensor
1) Diagram and pin

2) Installation position
Solar term door body.
3) Working principle
The sensor has a linear output angle sensor, comprising two arc-shaped sliding contact resistance
and the two sliding contact arm. Slide arm shaft with the solar term door is connected on the same
axis. With 5V Vcc supply voltage between two ends of A terminal and the B terminal sliding
contact resistance. When the throttle valve is rotated, the sliding contact arm rotates, and move in
the sliding contact resistance, and the potential of the VP contacts as output voltage derived from

11-13
 11. EFI SYSTEM OF SQR 472ENGINE
the C terminal. So it is in fact a angular potentiometer, potentiometer output and solar term door
position into a voltage signal proportional.
4) Technical parameters
The relationship between data for throttle valve opening and voltage as shown in the following table
Aperture(°) 0 10 20 30 40 50 60 70 80 85（Fully open）

Voltage（V） 0.33 0.78 1.25 1.71 2.17 2.63 3.08 3.52 3.99 4.5

Limit data
measure value unit
Mechanical angle between two extreme 119 angle
positions
The throttle body electrical angle between 8±2 angle
two extreme positions
Slide arm current license ≤18 μA
Storage temperature -40+130 ℃
Vibration acceleration license ≤700 m/s
Characteristic data
measure value unit
least typical maximum
Total resistance (pin A-B) 4.335 5.1 5.865 kΩ
Slider protecting resistor (slider at 710 1380 Ω
zero, pin B-C)
Operating temperature -40 130 ℃
The power supply voltage 5 V
The right extreme position of the 0.04 0.093
voltage ratio
The left extreme position of the 0.873 0.960
voltage ratio
VP/Vcc with the throttle angle 22 0.0009929 1/degree
increase rate
Weight 25 28 g

5) The malfunction phenomenon and the judgment method

(1) The fault phenomenon: can not enter the idle state; or step on the accelerator, accelerate the
powerless;
(2) The cause of failure of internal short circuit or open circuit: sensor; or throttle body to the engine
control unit Connection or short circuit breakers.
(3) Note: repair is not removable solar term door position sensor
(4) A simple method to measure
The power supply voltage measurement sensor A and B ends of the 5V;
Resistors A and B ends of the value is about
Signal C solar term door idle position of voltage between 0.3~0.7V;
Signal C is fully open when the voltage to ground between 4.05~4.75V.
11-14
 11. EFI SYSTEM OF SQR 472ENGINE
6. Idle speed control motor
1) Diagram and pin
11

2) installation position
Solar term door body.
3) working principle
Stepper motor is a miniature motor, it is encircled by a ring composed of a plurality of steel stator
and a rotor, see fig.. Each steel stator are around a coil; the rotor is a permanent magnet, permanent
magnet center is a nut. Stator coil all always electricity. As long as the change of one coil current
direction, a point of the rotor is turned. When the stator coil in the right order to change the current
direction, forming a rotating magnetic field of the permanent magnet, the rotor rotates in a direction.
If the order is reversed the direction of current change over, so the rotating direction of the rotor will
be upside down. Connect a wire rod drives the nut of the rotor center. Because the spiral rod is
designed into can not rotate, so it can only move in the axial direction, so it is also called linear axis.
End wire rod is a plug, plug and therefore can be retracted or extended, cross-sectional area to
increase or decrease the idle speed actuator bypass inlet passage, until it blocked. Whenever the
current direction change of a coil, rotor around a fixed point of view, called step, a number equal to
360 divided by the stator or coils. The stepping motor rotor step is 15. Accordingly, the screw rod
every move distance is fixed. ECU through the frequency control to replace the coil current
direction, to control the stepper motor moves, thereby regulating the bypass channel cross-sectional
area and flow of air traffic. The air flow in a linear relationship with the step. There is a spring plug
the back screw rod end, see below. Can be used in the plug the elongation direction of the force is
equal to the stepper motor force and spring force; the retracting direction can use force on the plug
is equal to the step force minus the spring force of stepping.

11-15
 11. EFI SYSTEM OF SQR 472ENGINE

4) Technical parameters
(1) Limit data
measure value unit
Least typical maximum
Working temperature -40 +125 ℃
Stepper motor plug contact the maximum 2.0x10° time
number of transposon
Characteristic data
value unit
Least typical maximum
Resistance of 20 ℃ each coil 47.7 53 58.3 Ω
Each coil resistance operating temperature range 35（-40℃） 95（+125℃） Ω
Inductance on 1000Hz 20 ℃ each coil 26.8 33.5 40.2 mH
Normal working voltage 7.5 12 V
May the work voltage 3.5 14 V
Stepper motor rotor length 0.04167 nm
The bypass passage is opened at both ends of the 60 kPa
pressure drop
Gas pressure difference caused by the maximum 6.28 N
axial force
5) Installation notes
Idle with stepping motor actuator is installed on the solar term door body castings, constitute a bypass channel at
both ends of the solar term door.
Bolt installation using two M5 0.8 14.
Bolt tightening torque of 4 0.4Nm.
The installation and use of the spring washer, and adhesive.
Idle with stepper motor actuator shaft should not be installed level or lower level, so as to avoid cold Condensate
water into.
Shall not be applied in any form of axial force to axial compression into or out of A.
Before the idle with stepper motor actuator into the solar term door body, the shaft must be fully retracted position
at.
11-16
 11. EFI SYSTEM OF SQR 472ENGINE

11

6) Fault phenomenon and judgment method

Fault phenomenon: idle speed is too high; idling flameout; idle vibration.
Repair the matters needing attention: 1, shall not be applied in any form of axial force to axial
compression into or out of a; Before 2, idle speed with stepping motor controller into the solar term
door body, the shaft must be fully retracted position at; 3, pay attention to the bypass air drain
cleaning and maintenance; 4, remove the battery or ECU, pay attention to timely to the stepper
motor reset.
A system reset method is: open the ignition switch but not immediately start the engine, wait 20
seconds, and then start the engine. If at this time that the engine idling bad, must repeat the above
steps.
A simple method to measure: (unloading joints) digital multimeter to Ohm, two probes are
respectively connected regulator AD, BC pin, 20 ℃ rated resistance was 53 ± 5.3Ω.
7. Heated oxygen sensor
1) Structure diagram and pin

2) Installation position
Exhaust manifold tail, before the three way catalytic converter
3) Working principle
The sensing element of the oxygen sensor is a kind of porous ceramic tube, tube wall is surrounded
outside of engine exhaust, the inside atmosphere. Sensing the ceramic tube wall is a kind of solid
electrolyte, with electric heating elements, see picture.

11-17
 11. EFI SYSTEM OF SQR 472ENGINE
The oxygen sensor is the oxygen ion concentration sensing ceramic tube inside and outside the difference into
voltage signal output implementation. When the sensing ceramic tube temperature reaches 350 ℃, which has the
characteristics of solid electrolyte. Because of its special material, the oxygen ions can freely through the ceramic
tube. It is the characteristic, the concentration difference into potential difference, thus forming electrical signal
output. If the gas mixture of concentrated. The ceramic tube and oxygen ion concentration is high, the high
potential difference, oxygen ions from the medial to lateral, the higher output voltage (close to 800mV~1000mV);
if the original lean mixture, the ceramic tube and oxygen ion concentration is low, the potential difference is low,
only a small amount of oxygen ions from the medial to lateral, the output voltage is low (close to
100mV~200mV). Signal voltage in the theory of equivalent air-fuel ratio (λ =1) occurred near mutation, see
below.

4) Technical parameters
Limit data
measure value unit
Least typical maximum
Working temperature Storage temperature -40 +100 ℃
Ceramic pipe 350 900 ℃
Case six hexagon nuts -40 600 ℃
Cable metal buckles and connecting -40 210 ℃
cable
Connector plug ≤120 ℃
The maximum allowable Ceramic tube short exhaust 950 ℃
temperature of the heating element Case six hexagon nuts 650 ℃
on the (each factory 10 minutes, a Cable metal buckles and connecting 250 ℃/s
total of up to 40 hours) cable
Rate of temperature change of ceramic tube end license 100 ℃/s
The rate of change of the six hexagon nut shell. 150 ℃
Housing permits 70~300 Hz 30 g
Connect the DC current at 350 ℃ ±10 μA
Exhaust temperature is 350 ℃, the maximum connection AC current ±10 μA
Fuel additives permit Unleaded gasoline, pay allows lead up
to 13mg/L.
The oil consumption and oil combustion Allowed values and data required by
the customer through the determination
of appropriate scale, test guideline
values: ≤ 0.25L/1000Km

11-18
 11. EFI SYSTEM OF SQR 472ENGINE
（2）Characteristic data
measure new 250 hours after the bench test
Exhaust temperature characteristics of data set 350℃ 850℃ 350℃ 850℃
Mixed gas concentration sensor voltage (Mv)
Mixed gas concentration sensor voltage (Mv)
750~920
40~100
710±70
55±30
840±80
20±50
710±70
40±40
11
The sensing element resistance (Km) 1~5 ≤0.1 ≤1.5 ≤0.3
Response time (Ma) (600mA to 300mA) 100~300 ＜200 ＜400 ＜400
Response time (Ma) (600mA to 300mA) 60~250 ＜200 ＜400 ＜400
（3）Sensor data
measure value unit
The new sensor with the At room temperature, the heating element (500V DC) ≥1 MΩ
insulation resistance Exhaust temperature 350℃ ≥10 MΩ
between element and the
Exhaust temperature 850℃ ≥100 KΩ
sensor joint
The power supply Rated voltage 12 V
voltage on the plug Working voltage 12 至 14 V
Working voltage up to 1% of the total life can be maintained, the exhaust 15 V
temperature ≤ 350 ℃
To maintain the working voltage of up to 75 seconds (exhaust temperature ≤ 350 24 V
℃)
The test voltage 13 V
The working voltage is 13V, the heating current at thermal equilibrium (exhaust temperature is 35 ℃, the 12 W
exhaust velocity of about 0.7M/s)

The working voltage is 15V, the heating current thermal equilibrium (350 ℃, the exhaust of greenhouse 5 A
gas flow velocity of about 0.7m/s)
Fuse filament heating circuit 8 A
(4) The use of life
Oxygen sensor life associated with gasoline lead content, see the following table.
Gasoline lead content (g/L) Life (km)
≤0.6 30000
≤0.4 50000
≤0.15 80000
≤ 0.005 (gasoline) 160000

4) Installation notes
Oxygen sensor should be installed in the exhaust gas mixing place, and when a vehicle moves, air cooling metal shell and wire
should be flow.
On the exhaust pipe can ensure the representative of the exhaust components and can meet the requirements of the temperature limit
position. Installation location should be as close as possible to the engine. The exhaust pipe should be provided with screw, screw in
oxygen sensor used for.
nstall the attitude of oxygen sensor
Oxygen sensor should be installed with the horizontal plane angle is greater than or equal to 45 degrees, and the sensor tip down, to
avoid the cold start of condensed water accumulated between the sensor housing and sensing ceramic tube.
Oxygen sensor wire can not bend more than 60 degrees, the bend arc radius is greater than or equal to 20 mm, and the wire should
not bear the tensile stress. The following diagram.

11-19
 11. EFI SYSTEM OF SQR 472ENGINE
The exhaust pipe of the request: to make the exhaust gas oxygen sensor in front region of the tube rapid heating. If
possible, the exhaust pipe should be designed to tilt, in order to avoid condensation water together in the front area
of the sensor.
Do not use cleaning fluid, oily liquids or volatile solids in the plug of the oxygen sensor.
Cannot use impact wrench fastening sensor.
Thread the oxygen sensor for M18 1.5-6e.
The six angle of the head size of oxygen sensor for 21.67~22.
Tightening torque 34~44Nm oxygen sensor.
5) Fault phenomenon and judgment method
Fault phenomenon: idling bad, bad acceleration, exhaust, fuel consumption is too large, exceed the standard.
Common fault: 1, 2 more than life, engine oil burning, causes the sensor surface area carbon 3, wet water vapor
inside the transducer, a temperature change, probe fracture; 2, oxygen sensor "poisoning". (Pb, S,
Br, Si)
Repair note: prohibit the use of cleaning liquid, oily liquids or volatile solids in the oxygen sensor in repair.
A simple method to measure:
(Remove connector) digital multimeter to Ohm, two probes are respectively connected sensor 1# (white), 2#
(white) pin, room temperature (23 ± 5 ℃) under the resistance of 5.4~6.6.
(Connect the connector) under idling state, the oxygen sensor at the working temperature of 350 ℃, the digital
multimeter to the DC voltage, two probes are respectively connected sensor 3# (grey), 4# (black) pin, the voltage
should be in the rapid fluctuation between 0.1-0.9V.
8. The intake air temperature and absolute pressure sensor
1) Structure diagram and pin

2) Installation position
The sensor consists of two sensors, intake manifold absolute pressure sensor and the inlet temperature sensor
assembly, is installed in the
The intake manifold.
3) Working principle
Intake manifold absolute pressure sensor element consists of a silicon chip. A pressure diaphragm etched on the
silicon chip. The pressure diaphragm has 4 piezoelectric resistance, the 4 piezoelectric resistance as the strain
components into a Wheatstone bridge. The silicon chip in addition to the pressure diaphragm, also has an
integrated signal processing circuit. The silicon chip with a metal shell to form a closed reference space, gas
reference space of the absolute pressure is close to zero. Thus forming a microelectronic mechanical system.
Active surface silicon chip has a close to zero pressure, its back through the manifold through a pipe into the test
tube, the absolute pressure. The silicon chip thickness of only a few microns (m), so the intake manifold absolute
pressure change makes silicon chip mechanical deformation, 4 piezoelectric resistance followed by deformation,
the resistance value change. By processing the signal processing circuit of silicon chips, forming the linear
relationship between the voltage signals and pressure. Intake air temperature sensor element is a negative
temperature coefficient (NTC) resistor, the resistance changes with the intake air temperature sensor, the
transmission to the controller a voltage representing the intake air temperature change.

11-20
 11. EFI SYSTEM OF SQR 472ENGINE
3) Technical parameters
(1) Limit data
measure value
Least typical maximum
unit
11
Tolerance power supply voltage for 1 hours 16 V
30 minutes of tolerance pressure 500 kPa
Tolerance Storage Temperature -40 +130 ℃

(2) Characteristic data

measure value unit
Least typical maximum
Pressure test range 10 120 kPa
Operating temperature -40 1230 ℃
Operating supply voltage 4.5 5.0 5.5 V
Current at U=5.5V. 10 mA
Or the load resistance of the battery 50 kΩ
Response time 7 Ms
Weight 27 g
(3) The limit data of temperature sensor
Storage temperature: -40/+130 ℃
(4) Characteristics of the data of temperature sensor
Operating temperature: -40/+130 ℃
Rated voltage: to lead resistance 1KΩ, Operation under 5 V, or to test the current running 1mA 20 ℃ rated
resistance: 2500 KΩ.
4) Installation notes
The sensor is designed for installation in the planes of an automobile engine intake manifold. Pressure pipe and
temperature sensor together out of the intake manifold, to realize the sealing of the atmosphere with a O ring. If
you take the right way to install to the car (extraction pressure, from the intake manifold pressure over sloped
down and so on), can not ensure the formation of condensed water pressure sensitive element. Drilling and fixed
on the intake manifold must be carried out in accordance with the supply, in order to ensure the long sealing and
erosion resistance of medium. Joint reliable electrical connection contact except mainly affected by components of
joint, but also with quality and size precision materials joints matched the wire harness. 6 bolt mounting torque is
8~10Nm
5) Fault phenomenon and judgment method
Fault phenomenon: poor idling flameout.
Common fault: 1, using the process of abnormal high pressure or reverse current; 2, the repair process of vacuum
element
Damage.
Repair note: impact to the vacuum unit using high pressure gas no repair process; find fault to replace the sensor
The time to check whether the generator output voltage and current of the normal.
A simple method to measure:
Temperature sensor:
(unloading joints) digital multimeter to Ohm, two probes are respectively connected sensor a#, b# pin, 20 ℃ rated
resistance is 2500KΩ, resistance value other corresponding can amount by the above characteristic curve.
Measurement can also be used when the simulation method, in particular to send wind direction sensor with a hair
dryer (note not reliable too close), observe the change of the sensor resistance, the resistance should be reduced.

11-21
 11. EFI SYSTEM OF SQR 472ENGINE

Pressure sensor:
(Connect the connector) The digital multimeter to DC voltage, the black pen grounding, the red pen
is respectively connected with the c#, the d# pin. The idle state, the reference voltage c# pin should
be 5V, d# pin voltage is about 1.3V (about a specific numerical and models); no load condition,
slowly open the solar term door, d# pin voltage change little; solar term door opened quickly,
voltage d# pin can instantly reach 4V left and right (specific numerical and vehicle), and then drops
to about 1.5V (the specific numerical and vehicle).

9. The fuel rail assembly

The fuel rail assembly consists of the fuel distribution pipe (rail), composed of four injector and
fixing clip.
1) Installation notes
Pay attention to dust, dust shall not be allowed to enter the pipe or plug injector nozzle;
Fuel rail assembly shall not bump, so as to avoid oil leakage accidents;
When installing the fuel injector sealing ring using clean, no silicone oil lubrication;
Oil inlet fuel rail assembly and from the tank pipe connection, should be fastened without leakage.
2) Installation position
The fuel rail assembly.

11-22
 11. EFI SYSTEM OF SQR 472ENGINE
3) Technical parameters
(1) Limit data
measure maximum
least typical maximum
maximum
11
Continuous work permit temperature -40 +120 ℃
The maximum allowable temperature of fuel +55 ℃
Maximum permissible pressure drift -30 ℃ (reversible) -2% 5%
Maximum permissible pressure drift -85 ℃ (reversible) -5% +2%
Maximum peak acceleration 350 m/s
The maximum pressure fluctuation value of import license 100 kPa

(2) Characteristic data

measure maximum unit
least typical maximum

Rated pressure difference flow Q=801// 370 380 390 kPa

Changes in the flow in the 15 to 140 1/h range of the working 20.5 kPa
pressure.
Flow range 10 280 L/h
A slope characteristic curve 0.165 kPa/L/h

(3) The requirement of fuel

Fuel pressure regulator can be used to meet the people's Republic of China national standard GB 17930-1999
"unleaded gasoline for vehicle and the" national environmental protection standards GWKB 1-1999 "standard"
harmful substance control gasoline regulations fuel.
4) Fault phenomenon and judgment method
Fault phenomenon: low fuel pressure or high, difficult to start.
General failure: due to long-term use: 1. Lack of maintenance, filter plug; 2. Impurity particles caused by large
leakage; 3. Man-made mechanical damage etc.
Repair the matters needing attention: 1. No impact of rail by high-pressure gas to oil; 2. A ban on the cleaned with
strong corrosive liquid; 3. No external force caused by deformation.
A simple method to measure:
Start the engine into the tubing connected to the fuel gauge,, enable the engine to run at idle speed, check the fuel
pressure is about 260kPa; pulling off the fuel pressure regulator vacuum tube on the observation time, the fuel
pressure is about 300kPa.
10. The fuel injector
1) Diagram and pin

11-23
 11. EFI SYSTEM OF SQR 472ENGINE
1 The fuel injectors for cylinders SM1 Power supply Main relay V_RLY
02 Injection signal ECU X1-24 IV1
3 The fuel injectors for cylinders SM1 Power supply Main relay V_RLY
02 Injection signal ECU X1-61 IV2
4 The fuel injectors for cylinders SM1 Power supply Main relay V_RLY
02 Injection signal ECU X1-23 IV3
2 The fuel injectors for cylinders SM1 Power supply Main relay V_RLY
02 Injection signal ECU X1-62 IV4
Pin: each injector has two pins SM1 and 02. Among them, the foot with SM1 identifies the main relay
The electrical output of 87 pin; another in accordance with 1, 2, 3, 4 cylinder are respectively connected with the
ECU X1-24, X1-62,
X1-61, B60 pin. V1~4 said the first to the fourth fuel injectors.
2) Installation position
One end of the cylinder head intake valve close.
3) Working principle
Injection time of ECU through pulse width to control fuel injector. Current flowing through the injector coil,
producing drag needle
The electromagnetic force, when the electromagnetic force increases to a certain extent, the needle was beginning
to rise, fuel injection process begins, when the current stops
When the needle valve, under the action of the spring, heavy and closed end, fuel injection process.
4) Technical parameters
(1) Limit data
measure Value
Least Typical maximum unit
Storage temperature (the original packaging) -30 +70
Permission temperature fuel injector in a car (not working) -30 +130
The working Continuous -30 +120
temperature of the After the hot start (about 5 minutes) -30 +130
fuel injector time
The fuel injector inlet Continuous -40 +110
fuel temperature A short time (about 3 minutes) -30 +130
Fuel flow relative to the deviation of 20 ℃ temperature can ＜-40 ＞+130
reach 4%.
The -35 to -40 temperature range of 0 - ring leakage license Allow fuel moisture 0 ring within the region, but
shall not divulge
(2) The allowable fuel
The injector can be used only in accordance with the people's Republic of China national standard GB
17930-1999 "unleaded gasoline for vehicle and the" national environmental protection standards GWKB 1-1999
"standard" harmful substance control of gasoline fuel and provisions, add detergent in gasoline. In particular,
gasoline is stored for long time will go bad. In particular, LPG and gasoline dual fuel engine in a taxi, long-term to
LPG as fuel, gasoline is used for starting, gasoline consumption rarely. But the long-term operation of fuel pump,
fuel tank temperature is high. If gasoline is stored in the car's fuel tank, it is very easy to be oxidized, may cause
injector blockage or damage.
Vibration acceleration maximum permissible (peak) 15 G
The power supply voltage 6 16 V
Insulation voltage 10 MΩ
Can afford to not fuel pressure 900 kPa
Capable of bending stress tolerance 6 Nm
Can withstand the axial stress 600 Nm
Characteristic data
measure Value unit
Least Typical maximum
Working pressure 200 300 400 kPa
(pressure difference)
Fuel injector resistance 12 Ω
at 20 ℃

11-24
 11. EFI SYSTEM OF SQR 472ENGINE
In particular, gasoline storage for a long time will go bad. In particular, LPG and gasoline dual fuel
engine in a taxi, long-term with LPG as fuel, gasoline is used for starting, gasoline consumption
rarely. But the fuel pump in long-term operation, oil temperature is high. If gasoline is stored in the
fuel tank, it is very easy to be oxidized, may cause the injector blockage or damage.
11
5) Installation notes
The fuel injector must must use certain plug, not mix.
In order to facilitate the installation, recommended the O ring is connected with the fuel distribution
pipes, and clean the oil surface of the lower O ring is connected with the intake manifold mounting
hole is coated with no silicon; to clean oil coated with no silicon surface fuel injector and the intake
manifold fuel distribution pipe mounting hole. Be careful not to let the oil pollution inside the
injector and nozzle.
The fuel injector to be perpendicular to the direction of the oil injector seat into the injector seat,
and then use the fuel injector is fixed on the spray clip
Oil filter base. Be careful.
The injector clamp by positioning for axial positioning clamp and axial and radial locating clamp,
should avoid misuse.
Fuel injector for the axial positioning of the installation slot, should ensure bayonet clip
intermediate completely card into the injector, card slot clamps on both sides of the complete card
into the outer edge flanging injector seat.
③ And injector axial and radial positioning requirements should be used for the axial and radial
locating clamp and the positioning of injector and fuel injector seat positioning pins are respectively
located at the card groove clip in the corresponding installation.
④ If fuel injector with two card slots, care should be taken not to card error, can refer to the original
installation position.
Fuel injector installation manual, no knocking injector with a hammer and other tools.
Removing and reinstalling the injector, must replace the O ring. At this time no damage on the
sealing surface of fuel injector.
Bearing washer O ring shall be pulled out from the injector. When installation should avoid damage
into the oil injector end, O ring, support ring, the orifice plate and the electric plug. If damaged,
should be banned.
Install injector fuel distribution pipe assembly tightness detection. No leakage of Fang Wei
qualified.
Failure to use manual disassembly. Remove the injector clamp, and then from the injector seat out
of fuel injector.
After the demolition should guarantee the injector seat clean, avoid pollution.
6) Fault phenomenon and judgment method
Fault phenomenon: idling bad, bad acceleration, can not start (starting difficulty); or the high fuel
consumption, exhaust black smoke.
General failure: due to lack of maintenance, lead to the injector internal glial accumulation and
failure, or a cylinder injector does not work; a cylinder injector often injection etc..
Note: repair (see installation notes)
A simple method to measure:
(unloading joints) digital multimeter to Ohm, two probes are respectively connected injector two
pin, 20 ℃ rated resistor of 12.
Suggestion: analytical instrument for regular cleaning of fuel injector using special injector
cleaning.
11-25
 11. EFI SYSTEM OF SQR 472ENGINE
11. Carbon canister solenoid valve
1) Diagram and pin

Pin: the carbon canister control valve has two pins, one by the main relay output pin, another ECU.
2) Installation position
The vacuum line on the carbon canister and intake manifold.
3) Working principle
The carbon canister control valve consists of an electromagnetic coil, armature and valve etc.. Inlet
is provided with a filter screen. Through the carbon canister control valve air flow of a connection
with the ECU output to the carbon canister control valve electric pulse duty ratio, on the other hand,
with the carbon canister control valve between the inlet pressure and the outlet pressure difference.
When no electric pulse, the carbon canister control valve closed.
The carbon canister control valve section

In the different pressure difference, the carbon canister control valve in the 100% duty cycle, i.e. all
open under the conditions of the flow of each are not identical. Here are two kinds of typical flow
curve. Can be seen from the graph, the 700mbar pressure difference, the carbon canister control
valve fully open when the flow rate is 3.8m3/h. In the 200mbar pressure difference, the carbon
canister control valve fully open when the flow rate is 3.0m3/h.

The carbon canister control valve flow chart

11-26
 11. EFI SYSTEM OF SQR 472ENGINE
4) Technical parameters
(1) Limit data
measure value unit
least typical maximum 11
working voltage 9 V
1 minutes over voltage 22 V
Minimum starting voltage 8 V
The minimum voltage drop 1.0 V
Permission temperature -30 +120 ℃
Working temperature term license +130 ℃
License storage temperature -40 +90 ℃
Can withstand the import and export pressure difference 800 Mbar
Licensing of switching frequency 8X107
License vibration acceleration product. 300 m/s2
Leakage of pressure difference at 700mbar 0.01 M3/h
(2) Characteristic data
measure value unit
least typical maximum
Rated voltage 13.5 V
+20℃Resistance 26 Ω
Stable voltage wires 0.5 A
The control pulse frequency 30 Hz
Typical control pulse width 10 ms
The differential pressure =200mbar duty ratio QA 2.7 3.0 3.3 m/h
100% of traffic
The differential pressure =700mbar duty ratio QB 3.5 3.8 4.1 m/h
100% of traffic

5) Installation notes
The carbon canister control valve and the carbon canister, intake manifold connected to see the
installation diagram

The carbon canister control valve installation diagram

In order to transfer to avoid solid sound, recommend the carbon canister control valve installed in
the pipe hanging on.
Must be installed with flow direction in accordance with the provisions, the installation direction
recommended vertical flip (i.e. the plug downwards vertically).
Must through the appropriate measures such as filtration, purification, to prevent foreign bodies
such as particulate matter from the carbon canister or hose into the carbon canister control valve.
Recommended to install a corresponding protective filter on the carbon canister outlet (mesh size 50
m).
6) Fault phenomenon and judgment method
Fault phenomenon: function failure.
11-27
 11. EFI SYSTEM OF SQR 472ENGINE
General failure: due to foreign body into the valve, leading to corrosion or poor sealing etc..
Repair note: 1, must be installed with flow direction in accordance with the provisions; 2, when the
body as black particles leads to a control valve failure, need to replace the control valve, please
check the carbon canister status; 3, repair process to avoid water, oil and other liquid into the valve;
4, in order to avoid solid transfer sound, recommend the carbon canister control valve installed in
the pipe hanging on.
A simple method to measure:
(remove electric connector) digital multimeter to Ohm, two one two pin the carbon canister control
valve respectively, 20 ℃ rated resistance was 26 ± 3.

12. The engine control unit (ECU)

1) installation position
The cockpit
2) principle of work
Multi-point sequential injection
Ignition control
Idle speed control
Provide power supply of sensor: 5V/100mA
Closed-loop control, adaptive
Control the carbon canister control valve
Air switch
The engine fault indicator
Fuel quantitative correction
The output of the engine speed signal (ESS signal)
The speed signal input
Fault diagnosis
Accept the engine load signal
etc..

11-28
 11. EFI SYSTEM OF SQR 472ENGINE
3) Technical parameters
Limit data
measure value unit
least typical maximum
11
Normal 8.0 16.0 V
The battery voltag operatio
n
Limited 6.0to8.0 16.0 To V
function 18.0
Battery over-voltage 16Vto24 Keep part of the function of the 60 S
tolerance limits and .2V engine can be started.
time 0to6V Storage automatic adaptive value
and fault code
The direction of
voltage tolerance
Working -40 +85 ℃
temperature
Storage temperature -40 +90 ℃

4) Note installation of electrostatic protection;

Pay attention to the protection of plug pin, waterproof ring check the wiring harness side within the
connector and yellow isolation plate is intact, prevent corrosion caused by poor contact pin.

5) Fault phenomenon and judgment method

Fault phenomenon: unstable idle speed, acceleration, not starting, idle speed is too high, exhaust,
exceed the standard starting difficulty, empty
Adjustable injector control failure, failure, flameout.

Common fault: 1, due to the external device electrical overload caused by ECU may lead to the
failure of internal parts burned; 2, because ECU water and cause the circuit board corrosion etc..
Note: 1. Repair repair process do not disassemble the ECU; remove the above battery first 5
minutes, remove 2 ECU; 3, after removal of the ECU storage; 4, banned in the ECU online
connection with any line.

A simple method to measure:

1. (Connect the connector) Using engine data K line read engine fault recording;
2. (Remove connector) Checking ECU connection line is intact, focus on examination of ECU
power supply, grounding line is normal;
3. Check whether the normal work of the sensor, the output signal is credible, the line is intact;
4. Check the actuator is working properly, the circuit is intact;
5. The replacement of the ECU test.

11-29
 11. EFI SYSTEM OF SQR 472ENGINE
13. Electric fuel pump

1) Installation position
Through the flange bracket is fixed in the tank,
Fuel pump relay Get an electric shock SW_A Battery anode V_BAT
SW_B Fuse pump ---
Coil Supply Main relay power supply V_RLY
ON ECU X1-69 RLY_EFP

Electric fuel pump with two pin, connect the fuel pump relay. Two stitches beside the pump shell
engraved with "+" and "-", respectively connected with positive and negative.
2) Working principle
Electric fuel pump is composed of pump and the end of the DC electric motor, a blade cover
(integrated check valve, pressure relief valve and the electromagnetic interference element) and
other components, see below.
Pump and motor are coaxially arranged, and closed in the same chassis. Around the pump and
motor shell are filled
Full of gasoline, the fuel cooling and lubrication. The battery to the electric fuel pump relay power
supply, relay
Only when in starting and running of the engine makes the electric fuel pump circuit. When the
engine is stopped by accident
When running, automatic stop fuel pump.

Graph: electric fuel pump profile

Electric fuel pump outlet pressure by the pressure relief valve, between 450 and 650kPa. But the
pressure in the fuel system from the fuel pressure regulator, 380kPa. According to the need of
engine, electric fuel pump can have different flow. For the convenience of production, the same
structure of the EKP13 series of electric fuel pump by adjusting step coils adjust the speed of the

11-30
 11. EFI SYSTEM OF SQR 472ENGINE
motor, thereby adjusting flow. So can not be electric fuel pump for vehicle use another type to.
3) Technical parameters
(1) Limit data
measure value unit
11
least typical maximum
working voltage 8 14 V（Direct Direct）
system voltage 380 kPa
Output voltage 450 650 kPa
The environment temperature (suitable for -40 +80 ℃
storage and transportation)
The license of the fuel temperature -30 +70 ℃
Vibration acceleration license 20 m/s
2) Characteristic data
Electric fuel pump in a fuel pressure flow with voltage proportional to. The oil pump using the car
plant of each are not identical.
Electric fuel pump capacity is 295-305g.
4) Installation notes
Electric fuel pump should be stored in the original packaging box sealed inside. Mounted on the car
after the maximum allowable storage time was 6 months, as accessories maximum storage time for
4 years. Over this time, by the manufacturers to test performance data pump. In the storage place,
must be protected against atmospheric effects of oil pump. During the storage period, the original
packaging shall not be damaged. Electric fuel pump is applied only to the fuel tank. Install the
pump must be installed on the eye size of not more than 60 or agreed with the customer common
inlet strainer. Please pay attention not to make the beam injection holes spewing oil into the oil inlet
filter, oil pump bracket and the oil tank wall. Be careful when handling pump. First of all, we must
protect the oil inlet filter is not affected by the load and impact. Oil pump should be installed to
carefully remove from plastic packaging materials. The protective cover only in the pump
immediately to install to take. Absolutely not allowed to take into the oil strainer. Foreign body into
the oil pump inlet or strainer can lead to pump damage. Install the tubing should pay attention to
clean. Tubing must be clean. Please use the new pipe clamp. Please make sure the hose clamp
The correct position, and follow the method recommended by the manufacturer. Not in the tubing
or in the inlet filter holding pump at. In order to prevent the pump is damaged, please don't run the
pump in the dry state. Do not use damaged pump and once fell to the oil pump on the ground. Oil
fell to the ground, to replace the pump tank. Pressure is not allowed in the oil inlet plate. Caulking
can not have mechanical stress. Pump clamp must be within the scope of the provisions, see below.

Graph: Pump clamping range

If the pump has been used, please rinse with test solution, and dry in the air. Do not allow the oil
pump.
11-31
 11. EFI SYSTEM OF SQR 472ENGINE
5) Fault phenomenon and judgment method
Fault phenomenon: running noise, poor acceleration, can not start (starting difficulty) etc..
General failure: due to the use of inferior fuel,: 1, glial accumulation formed on the insulating layer;
2. Oil pump bushing and armature lock; 3. oil level sensor assembly corrosion.
Repair note: 1. according to the need of engine, electric fuel pump can have different flow, fuel
pump has the same shape, can hold up is not necessarily appropriate, part No. fuel pump repair by
must be with the original agreement, is not allowed to change the wrong; 2. in order to prevent
accidental damage to the fuel pump, please don't run in the dry state; 3. the need to replace the fuel
pump, please pay attention to the fuel tank and pipeline cleaning and replacing fuel filter.
A simple method to measure:
(Remove connector) Digital multimeter to Ohm, two probes are respectively connected fuel pump
two pins, measuring internal resistance, not zero or infinity (i.e. not short circuit, open circuit state).
(Connect the connector) To start the engine into the tubing connected to the fuel gauge, fuel pump,
observe whether work; if it is not running, check the "+" pin if there is power supply voltage; if the
operation, the idle condition, check the fuel pressure is about 260kPa; off the fuel pressure regulator
vacuum tube, whether fuel when the pressure is about 300kPa.
14. The ignition coil

1) installation position
Installed in the engine compartment
2) working principle
Using double-coil cylinder at the same ignition system
3) technical parameters
Room temperature 23 ℃, typical working voltage of 14V, the primary coil current 7A, secondary
output with 50pF load is 38KV - 10%.

11-32
 11. EFI SYSTEM OF SQR 472ENGINE
4) Installation notes
Requirements for fixed bolt and nut firmly, to prevent loosening caused by vibration, ignition coil,
mechanical damage.
5) Fault phenomenon and judgment method 11
The high-pressure line on the engine pulled out, the spark plug on good, will spark plug metal shell
on the engine body, by the spark plug spark ignition coil and the high-voltage wire to judge whether
good.
15. Three way catalytic converter
1) Installation position
Welding in the exhaust manifold pipe assembly
2) Working principle
In the three way catalytic converter, CO, HC, NOx respectively, the reduction reaction of oxidation
of harmless CO2, H2O and N2, containing precious metal platinum in the carrier (Pe) and (Pd) and
rhodium (Rh) of noble metal catalysts. Reaction formula of it as follows: 2CO2NO==2CO2N2
4HC10NO==4CO22H2O5N2. There is a close relationship between the catalyst efficiency height
and temperature, the use of harmful components from the exhaust gas temperature to ideal
operating condition transformation temperature more than 300 degrees Celsius and the catalytic
converter for 400-700 degrees, the maximum allowable temperature is 850-920 degrees Celsius, or
noble metal may produce thermal aging, mainly due to activation surface temperature failure and
alumina sintering. Catalytic converter conversion efficiency and air-fuel ratio, in the ideal air-fuel
ratio (14.7:1) narrow area is (14.5-15.0) catalyst for CO, HC and NOx conversion efficiency
reached the highest at the same time. When the air-fuel ratio is too thick, the pollutant conversion
Efficiency were decreased, CO and HC is more obvious; while too thin when CO and HC
conversion efficiency significantly, NOx was significantly lower.
3) Installation notes
Transport and installation, should be light-light, forbid throwing. If you hear the three way catalytic
converter assembly has abnormal noise, possible catalyst carrier rupture, exploratory confirmation.
To add high quality gasoline engine failure, to prevent poisoning catalyst, influence the emission.
4) Fault phenomenon and judgment method
If the exhaust pipe assembly has abnormal noise, or the exhaust back pressure is too high, or driving
performance variation accelerate the powerless, visually exploration catalyst carrier is melting the
blockage, or rupture.
16, The other is connected with ECU signal
Malfunction 1 Power supply V_RLY
indicator 2 Fault display signal ECU X1_107 MIL
lampCAN
1 CAN High ECU X1_17 CAN 1_N
Line for Tool
2 CAN Low ECU X1_6 CAN 1_L
That engine speed signal of engine tachometer ECU X1_66 ESS
The speed signal (Holzer) ECU X1_12 VS
Air conditioner evaporator Signal A ECU X1_12 EXAP
temperature sensor Signal B ECU X1_13 EVAP_G
ND

11-33
 11. EFI SYSTEM OF SQR 472ENGINE
Chapter 3 Introduces the function of fault diagnosis system
The electronic control unit continuously monitoring sensor, actuator, circuit, fault indicating lamp
and battery voltage and so on, and the electronic control unit itself, and the actuator driving signal
and the internal signal of the sensor output signal, (such as closed loop control, coolant temperature,
the idle speed control and battery voltage control) for reliability detection. Once found a link failure,
or a signal value is not trusted, the electronic control unit immediately set up fault information
recorded in the fault memory in the RAM. Fault recording information stored in the fault code form,
has the display order according to the faults.
According to the fault frequency can be divided into "fault" and "breakdown" (such as wire harness
circuit transient
Due to poor contact or connector).
1 control, fault lamp
When no fault
★ ignition switch ON, fault light;
★ fault detection speed signal lamp;
When there is a fault
★ ignition switch ON, fault light;
★ starting, find the speed signal out, if the fault lamp fault class is defined as a light mode, then
meet the corresponding
Confirmation conditions after the fault light;
To connect 2, diagnostic instrument
This system uses the "K" line of communication protocol, and uses the ISO 9141-2 standard
diagnostic connector, see below. The criteria for the diagnosis of joint is fixedly connected on the
engine wire harness. With the engine management system EMS is the standard diagnostic connector
on the 4, 7 and 16 pin. Criteria for the diagnosis of joint 4 pin connected wire on the vehicle; 7 pins
connected to a ECU 77 pin, namely engine data "K" line; 16 pin connected battery.

Figure ISO9141-2 standard diagnostic connector (connected to the engine control unit side)
The ECU communicates with external diagnostic device through the "K" line, and can perform the
following operations:
(the function and diagnosis instrument operation refer to "diagnostic instrument using the")
1), the engine parameter display
1, rotational speed, coolant temperature, solar term door opening, ignition advance angle, injection
pulse width, inlet pressure, inlet temperature, speed, voltage, injection correction, the carbon
canister erosion rate, the idle air control, oxygen sensor waveform;
11-34
 11. EFI SYSTEM OF SQR 472ENGINE
2. The target speed, engine load, ambient temperature, relative ignition dwell time, the evaporator
temperature, gas flow rate, fuel consumption;
3. Solar term door position sensor signal voltage, coolant temperature sensor signal voltage, the
intake air temperature sensor signal voltage, the intake pressure sensor signal voltage. 11
2) EFI system status display
Anti-theft system state, safety state, program state, cooling system condition, stable condition,
dynamic condition, emission control state, the status of the oxygen sensor, the idle state, the
malfunction indicator lamp status, emergency condition, air conditioning system, automatic
transmission / torque request status.
3) Actuator test function
Fault lamp, fuel pump, air conditioning, fan relay, ignition, fuel injection (single-cylinder oil).
4) Odometer display
The running mileage, the running time.
5) Version information display
Frame number (VIN), ECU hardware number, ECU number.
6) Fault display
The intake pressure sensor, intake temperature sensor, engine coolant temperature sensor, solar term
door position, sensor, oxygen sensor, oxygen sensor heater circuit, air-fuel ratio correction, each
cylinder injector, fuel pump, speed sensor, phase sensor, the carbon canister control valve, cooling
fan relay, vehicle speed signal, the idle speed, idle speed adjustment device, system voltage, ECU,
air conditioning compressor, evaporator temperature sensor, relay fault lamp.
3. The fault code list

number failure code

1 P0031 Oxygen sensor 1 heater control circuit shorted to ground
2 P0032 Oxygen sensor 1 heater control circuit shorted for the power supply circuit
3 P0037 Oxygen sensor 2 heater control circuit shorted to ground
4 P0038 Oxygen sensor 2 heater control circuit shorted for the power supply circuit
5 P0107 Manifold pressure sensor circuit shorted to ground
6 P0108 Manifold pressure sensor circuit shorted for the power supply circuit
7 P0112 Intake air temperature sensor circuit shorted to ground
8 P0113 Intake air temperature sensor circuit shorted for the power supply circuit
9 P0116 Coolant temperature sensor circuit scope / nature of the error
10 P0117 Coolant temperature sensor circuit shorted to ground
11 P0118 Coolant temperature sensor circuit shorted for the power supply circuit
12 P0119 Coolant temperature sensor circuit intermittent
13 P0122 Solar term door position sensor for short circuit to ground
14 P0123 Solar term door position sensor for short circuit of power supply
15 P0130 Oxygen sensor 1 circuit fault
16 P0131 Oxygen sensor 1 circuit output voltage is too low
17 P0132 Oxygen sensor 1 circuit output voltage is too high
18 P0134 Oxygen sensor 1 is not activated
19 P0136 Oxygen sensor 2 circuit fault

11-35
 11. EFI SYSTEM OF SQR 472ENGINE
20 P0137 Oxygen sensor 2 circuit output voltage is too low
21 P0138 Oxygen sensor 2 circuit output voltage is too high
22 P0140 Oxygen sensor 2 is not activated
23 P0230 Circuit pump failure
24 P0261 One cylinder injector circuit shorted to ground
25 P0262 One cylinder injector circuit shorted for the power supply circuit
26 P0264 Two cylinder injector circuit shorted to ground
27 P0265 Two cylinder injector circuit shorted for the power supply circuit
28 P0267 Three cylinder injector circuit shorted to ground
29 P0268 Three cylinder injector circuit shorted for the power supply circuit
30 P0270 Four cylinder injector circuit shorted to ground
31 P0271 Four cylinder injector circuit short for the power supply circuit
32 P0325 Knock sensor circuit failure
33 P0335 Crankshaft position sensor circuit failure
34 P0340 Camshaft position sensor fault
35 P0351 One cylinder ignition coil circuit fault
36 P0352 Two cylinder ignition coil circuit fault
37 P0353 Three cylinder ignition coil circuit fault
38 P0354 Four cylinder ignition coil circuit fault
39 P0444 The carbon canister control valve circuit open
40 P0445 The carbon canister control valve circuit shorted
41 P0501 Speed sensor is not working properly
42 P0505 Idle stepper motor fault
43 P0560 The system voltage fault
44 P0605 ECU (read-only memory) fault
45 P0650 Malfunction indicator lamp control circuit fault
46 P1166 Oxygen sensor controller adaptive fault diagnosis
47 P1502 Wheel speed sensor circuit open
48 P1535 Air conditioning evaporator temperature sensor for short circuit or open
circuit power supply
49 P1536 Short circuit of the air conditioning evaporator temperature sensor circuit
50 P1545 High voltage switch or air conditioning clutch relay line fault
51 P1624 Cooling fan relay line fault – low speed
52 P1625 Cooling fan relay line fault - high speed

11-36
 11. EFI SYSTEM OF SQR 472ENGINE
4. Clear fault codes
The use of diagnostic instrument
1) Turn off the ignition switch. 11
2) By reading the fault code the same method, the diagnosis instrument to diagnose interface.
3) Connected to the ignition switch.
4) According to the diagnostic tester instructions clear fault code.
5) To complete the fault code is cleared, exit diagnosis procedure, switch off the ignition and
remove the diagnosis instrument from the diagnostic interface.

Do not use diagnosis instrument and computer

1) Turn off the ignition switch.
2) Disconnect battery cathode line for more than 30 seconds, then go on.
Note: the fault does not exclude, fault codes will reappear

11-37
 11. EFI SYSTEM OF SQR 472ENGINE
Chapter 4 Troubleshooting diagnostic process
1. Fault diagnosis based on the fault code description
1. Has been recognized as a steady-state current failure to the following maintenance, otherwise it
will lead to wrong diagnosis.
2. The below mentioned "multimeter occasion" refers to the digital multimeter, prohibit the use of
pointer multimeter to check on line electronic fuel injection system.
3. Maintenance of the vehicle anti-theft system, if the replacement ECU occasions appeared in the
"Next step" bar, pay attention to after the replacement of programming on ECU.
4. If fault code for a circuit voltage is too low, refers to the circuit may be shorted to ground; if the
fault code for a circuit voltage is too high, refers to the circuit has the potential to supply short
circuit; if the fault code for a circuit fault, refers to the circuit breaker may exist in or there are a
variety of line fault.
Diagnostic aid:
1. The fault code cannot clear, failure is a fault; if the breakdown of key check whether there is
loose in the wire harness connector.
2. According to the steps examination, no abnormal situation;
3. The maintenance process don't ignore automobile maintenance, cylinder pressure, mechanical
ignition timing and the influence on the system;
4. Replacing ECU, test. If fault code can remove the fault location, fault code in the ECU, if still
unable to clear, is for the original ECU, repeat the process again, repair work.

2、Fault code diagnosis flow

2.1. The upstream oxygen sensor heater control circuit shorted to ground (fault code P0031)
Serial Operation Vehicl Next step
numb e
er speed
detecti
on
1 Connect the diagnostic instrument, ignition switch is Next step
in the "ON"
2 Dial the joint oxygen sensor wire harness, check with yes Next step
a multimeter, the joint 1# (connected with the oxygen
sensor white relative), 2# (with the oxygen sensor no To step 4
cable relative to white) is 12V about the value of
voltage at pin.
3 Using a multimeter to check the oxygen sensor 1# yes Next step
(white), 2# (Baise) resistance between Pin value at no Replace the sensor
20 ℃ in 5.4~6.6 ohm
4 15A fuse check the main relay power lines of the yes Replace the fuse
fuse no Next step
5 X1_8# main relay X1_21# pin check ECU yes Repair or replace the wire
respectively (1# and oxygen sensor connector for harness
connecting line is legendary white), 2# (with the no Diagnostic aid
oxygen sensor white connection line between pins
relative) whether the circuit breaker or short circuit
to ground

11-38
 11. EFI SYSTEM OF SQR 472ENGINE
2.2. The upstream oxygen sensor heater control circuit for the power supply circuit (fault code
P0032)
Serial Operation steps Test Next step
number
1 Connect the diagnosis instrument, the ignition
results
Next step
11
switch is in the "ON"
2 Dial the joint oxygen sensor wire harness, check yes Next step
with a multimeter, the joint 1# (connected with the
No To step 4
oxygen sensor white relative) is about 12V value
between I voltage at pin
3 Using a multimeter to check the oxygen sensor 1 yes Next step
(white), 2#(white) resistance between Pin value at 2
No Replace the sensor
℃ in 5.4~6.6 ohm
4 15A fuse check the main relay power lines of the No Replace the fuse
fuse yes Next step
5 Check the ECU X1-8#, the main relay X1_21# No Repair or replace the wire
pins respectively in sensor connector 1# (and harness
oxygen sensor connector, relative to white) 2# yes Diagnostic aid
(with the oxygen sensor is connected between pins
relative color line) to supply short circuit)

2.3. The lower the oxygen sensor heater control circuit shorted to ground (fault code P0037)
order Operation steps Test Next step
number results
1 Connect the diagnostic instrument, ignition switch Next step
is in the "ON”
2 Dial the joint oxygen sensor wire harness, check yes Next step
with a multimeter, the joint 1# (with the oxygen No To step 4
sensor cable relative to white) is 12V about the
value of voltage at pin.
3 Using a multimeter to check the oxygen sensor 1# yes Next step
(white), 2# (white) resistance between Pin value at No Replace the sensor
20 ℃ in 5.4~6.6 ohm
4 15A fuse check the main relay power lines of the yes Replace the fuse
fuse 15A fuse check the main relay power lines of No Next step
the fuse
5 X1_9# main relay X1_21# pin check ECU yes Repair or replace the wire
respectively in sensor connector 1# (and oxygen harness
sensor connector, white 2# (relative) and oxygen No Diagnostic aid
sensor connector pins between white relative)
whether the circuit breaker or the open.

11-39
 11. EFI SYSTEM OF SQR 472ENGINE
2.4. The lower oxygen sensor heater control circuit for the power supply circuit (fault code P0038)
Serial Operation steps Test Next step
number results
1 Connect the diagnostic instrument, ignition switch is Next step
in the "ON"
2 Dial the joint oxygen sensor wire harness, check Yes Next step
with a multimeter, the joint 1# (and oxygen sensor No To step 4
connector, white 2# (relative) and oxygen sensor
connector relative to white) is 12V about the value
of voltage at pin.
3 Using a multimeter to check the oxygen sensor 1# Yes Next step
(white), 2# (white) resistance between Pin value at No The replacement of Xu
20 ℃ in 5.4~6.6 ohm feelings
4 15A fuse check the main relay power lines of the Yes Replace the fuse
fuse
No Next step
5 Check the ECU X1_9#, the main relay X1 -- 21# Yes Repair or replace the wire
pins respectively and sensor connector 1# (and harness
oxygen sensor connector, relative to white) 2# No Diagnostic aid
(relative with the oxygen sensor cable) whether to
short circuit of power supply pin.

2.5. Manifold pressure sensor circuit shorted to ground (fault code P0107)
Serial Operation steps Test Next step
number results
1 Connect the diagnostic instrument, ignition switch is Next step
in the "ON"
2 The observed data stream "pressure", is about Yes To step 5
101kPa (numerical and Kia) No Next step
3 Dial the joint air inlet pressure sensor on wire Yes To step 5
harness, multimeter voltage check the joint 2# and No Next step
4# pins between whether the value is about 5V
4 Check the ECU X1_60#, X1_46#, X1_48# pins Yes Repair or replace the wire
were in line between the sensor connector, 1#, 2#, harness
4# pin is broken No Next step
5 Start the engine, idle running. Slow down on the Yes Diagnostic aid
accelerator to close to the fully open, to observe the No Replace the sensor
diagnostic instrument "pressure" value changes, the
display values should change little; quick throttle to
close to the fully open, the display values should be
can instantly reach above 90kPa.

11-40
 11. EFI SYSTEM OF SQR 472ENGINE
2.6. Manifold pressure sensor circuit for the power supply circuit (fault code P0108)
Serial Operation steps Test Next step
number results
1 Connect the diagnostic instrument, ignition switch is
in the "ON"
Next step 11
2 The observation data stream of "pressure". It is Yes To step 5
about 101kPa (numerical and pressure). No Next step
3 Dial the joint air inlet pressure sensor on wire Yes To step 5
harness, multimeter voltage check the joint 2# and
No Next step
4# pins between whether the value is about 5V
4 Check the ECU X1_60#, X1_46#, 1_48# Yes Repair or replace the wire
respectively in the line between the sensor harness
connector for 1#, 2#, 4# pin is broken No Next step
5 Start the engine, idle running. Slow down on the Yes Diagnostic aid
accelerator to close to the fully open, observation
instrument monk "pressure" numerical variation No Replace the sensor
diagnosis, the display value a little change; quick
throttle to close to the fully open, the display values
should be can instantly reach above 90kPa.

2.7. The intake air temperature sensor circuit shorted to ground (fault code P0112
Serial Operation steps Inspec Next step
number tion
results
1 Connect the diagnosis instrument, the ignition Next step
switch is in the "ON".
2 The observation data stream in the "air Yes To step 5
temperature", whether in the intake pipe of
No Next step
equivalent temperature (numerical and when the
engine temperature). Note: if the display value
often is constant, that there may be line short circuit
fault
3 Dial connection wire harness the intake air Yes Next step
temperature sensor, using a multimeter check No Replace the sensor
resistance sensor 3# and 4# pins of value is
commensurate with its temperature (with specific
reference to the relevant part of the repair manual).
4 Dial the air intake temperature sensor connector on Yes To step 6
wire harness, multimeter voltage check the joint a# No Next step
and b# pins between whether the value is about 5V
5 Check the ECU X1_56#, X1_48# between pin are Yes Repair or replace the wire
respectively connected with the sensor connector, harness
pin 3# 4# whether the circuit breaker. No Next step
6 Start the engine, idle running. To observe the Yes Diagnostic aid
diagnostic instrument "air temperature" value No Replace the sensor
changes, the display values should be increased
along with the engine air inlet temperature
11-41
 11. EFI SYSTEM OF SQR 472ENGINE
2.8. The intake air temperature sensor circuit for the power supply circuit (fault code P0113)
order Operation steps Test Next step
number results
1 Connect the diagnostic instrument, ignition switch Next step
is in the "ON"
2 The observed data stream "air temperature". Yes To step 5
Whether in the intake pipe of equivalent
No Next step
temperature (numerical and when the engine
temperature). Note: if the display value of
gastrointestinal constants, that there may be line
short circuit fault.
3 Dial the joint air inlet pressure sensor on wire Yes Next step
harness, electrical multimeter check sensor 3# and
4# pins of value is commensurate with its No Replace the sensor
temperature (with specific reference to the
evaluation of repair manual).
4 Dial the joint line beam. The temperature sensor, Yes To step 6
using a multimeter check resistance sensor a# and
No Next step
b# pins between whether the value is about 5V
5 Check the ECU X1_56#, X1_548# between pin Yes Repair or replace the wire
closure and sensor connector, pin 3# 4# whether the harness
circuit breaker No Next step
6 Start the engine, idle running. To observe the Yes Diagnostic aid
diagnostic instrument "air temperature" value No Replace the sensor
changes, the display values should be increased
along with the engine air inlet temperature

11-42
 11. EFI SYSTEM OF SQR 472ENGINE
2.9. The coolant temperature sensor circuit output range / character error (error code P0116)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the ignition Next step 11
switch is in the "ON".
2 The observed data stream "coolant temperature", Yes Next step
and whether the engine temperature quite No To step 4
(numerical and when the engine temperature). Note:
if the display value often is constant, that there may
be circuit breaker failure.
3 Connector for coolant temperature sensor unplug Yes Next step
the wire harness, electrical multimeter check sensor
a# and c# pins of value is commensurate with its No Repair or replace the wire
temperature (with specific reference to the relevant harness
part of the repair manual).
4 Connector for coolant temperature sensor unplug Yes
the wire harness, multimeter voltage check the joint No Next step
a# and c# pins between whether the value is about
5V.
5 Check the ECU X1-31#, X1-73# between pin are Yes Repair or replace the wire
respectively connected with the sensor connector, harness
pin a# c# whether the circuit breaker. No Next step
6 Start the engine, idle running. To observe the Yes Diagnostic aid
diagnostic instrument "coolant temperature" value No Replace the sensor
changes, the display values should be increased
along with the engine coolant temperature.

11-43
 11. EFI SYSTEM OF SQR 472ENGINE
2.10. The coolant temperature sensor circuit shorted to ground (fault code P0117)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the ignition Next step
switch is in the "ON".
2 The observed data stream "coolant temperature", and Yes To step 6
whether the engine temperature quite (numerical and
No Next step
when the engine temperature). Note: if the display
value often is constant, that there may be circuit
breaker failure.
3 Dial the connector for coolant temperature sensor Yes Next step
wire harness, electrical multimeter check sensor a# No Replace the sensor
and c# pins of value is commensurate with its
temperature (with specific reference to the relevant
part of the repair manual).
4 Dial the connector for coolant temperature sensor Yes To step 6
wire harness, using a multimeter to check the joint No Next step
line between the a#, c# pin is broken
5 Check the ECU X1_31#, X1_73# between pin are Yes Repair or replace the wire
respectively connected with the sensor connector, harness
pin a# c# whether the circuit breaker. No Next step
6 Start the engine, idle running. To observe the Yes Diagnostic aid
diagnostic instrument "coolant temperature" value
No Replace the sensor
changes, the display values should be increased
along with the engine coolant temperature

2.11. The coolant temperature sensor circuit for the power supply circuit (fault code P0118)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the ignition Next step
switch is in the "ON"
2 The observed data stream "coolant temperature", Yes To step 6
and whether the engine temperature quite
No Next step
(numerical and when the engine temperature).
Note: if the display value often is constant, that
there may be circuit breaker failure.
3 Dial the wire harness connector on coolant Yes Next step
temperature sensor

11-44
 11. EFI SYSTEM OF SQR 472ENGINE
2.12. The coolant temperature sensor circuit discontinuity (fault code P0119)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the ignition
switch is in the "ON"
Next step 11
2 The observed data stream "coolant temperature", Yes To step 6
and whether the engine temperature quite (specific No Next step
figures and then the engine temperature related).
Note: if the display value often is constant, that
there may be circuit breaker failure.
3 Dial the connector for coolant temperature sensor Yes Next step
wire harness, electrical multimeter check sensor a#
No Replace the sensor
and c# pins of value is commensurate with its
temperature (with specific reference to the relevant
part of the repair manual).
4 Dial the connector for coolant temperature sensor Yes To step 6
wire harness with a multimeter to check voltage, No Next step
the joint a# and c# pins of about 5V.
5 Check the ECU X1_31#, X1_73# pin, respectively Yes Repair or replace the wire
in the line between the sensor connector a#, pin is harness
open circuit c#. No Next step
6 Start the engine, idle running. Observation of the Yes Diagnostic aid
road "Party member on the coolant temperature" No Replace the sensor
value changes, the display values should be
increased after the engine coolant temperature and
elevated.
2.13. Solar term door position sensor circuit shorted to ground (fault code P0122)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the ignition Next step
switch is in the "ON"
2 The observation data stream of "solar term door is Yes Next step
opening", value is between 4%~10% (numerical and No To step 5
models have different).
3 Slow down on the accelerator to the fully open, the Yes Next step
observation data stream of "solar term door is
opening", whether the data with the throttle opening No To step 5
increases to about 85~95% (specific data and
models are different)
4 Repeat step 3, the observation data stream of "solar Yes Replace the sensor
term door is opening", whether the existence of No Next step
value changes in the process of change.
5 Dial the joints of I solar term valve position sensor Yes Repair or replace the wire
wire harness, check the ECU X1_45#, X1_38#, harness
X1_32# pin connected circuit between a#, a#, c# pin No Next step
on the sensor circuit breaker or whether,
respectively on the power circuit.
6 Using a multimeter to check voltage a# and b# pins Yes Replace the sensor
of the joint between the value is about 5V. No Diagnostic aid

11-45
 11. EFI SYSTEM OF SQR 472ENGINE
2.14. Solar term door position sensor circuit for the power supply circuit (fault code P0123)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 The observation data stream of "solar term Yes Next step
door is opening", value is between 4 $~10% No To step 5
(numerical and models have different).
3 Slow down on the accelerator to the fully Yes Next step
open, the observation data stream of "solar No To step 5
term door is opening" think, numerical with
the throttle opening increases to about
85~95% (specific numerical models are
different, and in).
4 Repeat step 3, the observation data stream Yes Replace the sensor
of "solar term door is opening", whether the No Next step
existence of value changes in the process of
change.
5 Solar term door shifting joint position Yes Repair or replace the wire harness
sensor wire harness between ECU, check
X1_45#, X1_38#, X1_32#, a#, b# dB and No Next step
sensor connector, pin, c# whether the circuit
breaker short-circuit or short circuit of
power supply.
6 Using a multimeter to check voltage a# and Yes Replace the sensor
b# pins of the joint between the value is No Diagnostic aid
about 5V
2.15. The oxygen sensor circuit fault (fault code P0130)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 43# X1_59# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

11-46
 11. EFI SYSTEM OF SQR 472ENGINE
2.16. Oxygen sensor circuit output voltage is too low (fault code P0131)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step 11
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 43# X1_59# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

2.17. Oxygen sensor circuit output voltage is too high (fault code P0132)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 43# X1_59# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

11-47
 11. EFI SYSTEM OF SQR 472ENGINE
2.18. The oxygen sensor is not active (error code: P0134)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 43# X1_59# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

2.19. The oxygen sensor circuit fault (fault code P0136)

Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 42# X1_37# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

11-48
 11. EFI SYSTEM OF SQR 472ENGINE
2.20. Oxygen sensor circuit output voltage is too low (fault code P0137)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step 11
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 42# X1_37# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

2.21. Oxygen sensor circuit output voltage is too high (fault code P0138)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 42# X1_37# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

11-49
 11. EFI SYSTEM OF SQR 472ENGINE
2.22. The oxygen sensor is not active (fault code P0140)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON”
2 Start the engine, idle running to the Yes Diagnostic procedures
coolant temperature reach normal values,
No Next step
observe diagnosis instrument monk
"oxygen sensor voltage" items to pay
changes, the display values should lose
uncle is in the range of 100Ma~900mA
3 Check the ECU X1 -- 42# X1_37# pins Yes Repair or replace the wire harness
respectively in sensor connector 3# (with No Next step
the oxygen sensor grey connection line
between pins) line is faulty.
4 Exhaust system blocking Yes Maintenance according to the
Fuel injector is leaking diagnosis
Fuel pressure is too large No Diagnostic aid
Valve clearance is too small.

2.23. Pump primary line fault (fault code P0230)

Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "OFF"
2 Pulling off the fuel pump relay, the Yes To step 4
ignition switch to "ON", respectively,
No Next step
check the pump relay power supply
terminal 30# 86# power supply voltage
pin and pay some value is around 12V
3 Check relay power supply line is broken Yes Repair or replace the wire harness
or short circuit to ground. No To step 2
4 Check with a multimeter pump relay Yes Replace the fuel pump relay
control terminal relay 85# pins and power No Next step
to pay a few pieces of the resistance value
is about 3.7V.
5 Check relay control end is between the Yes Repair or replace the wire harness
X1_69# pin and the ECU pin relay 85# No Diagnostic aid
whether the circuit breaker or the power
or the open.

11-50
 11. EFI SYSTEM OF SQR 472ENGINE
2.24. A cylinder injector circuit shorted to ground (fault code P0261)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step 11
ignition switch is in the "ON"
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
No Next step
connector SM1# pin voltage and power for a
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin No Next step
and the negative pole of the power supply
will be.
6 Between the X1_24# pin check cylinder Repair or replace the wire harness
injector connector 2# pin and the ECU line
Diagnostic aid
is broken or the power supply or short circuit
to ground.

11-51
 11. EFI SYSTEM OF SQR 472ENGINE
2.25. A cylinder injector circuit for the power supply circuit (fault code P0262)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_24# pin check cylinder Yes Repair or replace the wire harness
injector connector 2# pin and the ECU line is
broken or the power supply or short circuit to No Diagnostic aid
ground.

2.26. Two cylinder injector circuit shorted to ground (fault code P0264)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_62# pin check cylinder Yes Repair or replace the wire harness
injector connector 2# pin and the ECU line is
broken or the power supply or short circuit to No Diagnostic aid
ground.
11-52
 11. EFI SYSTEM OF SQR 472ENGINE
2.27. Two cylinder injector circuit for the power supply circuit (fault code P0265)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the
ignition switch is in the "ON"
Next step 11
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_62# pin check cylinder Repair or replace the wire harness
injector connector 2# pin and the ECU line is
broken or the power supply or short circuit to Diagnostic aid
ground.

2.28. Three cylinder injector circuit shorted to ground (fault code P0267)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_61# pin check cylinder Yes Repair or replace the wire harness
injector connector 2# pin and the ECU line is
Diagnostic aid
broken or the power supply or short circuit to
ground.
11-53
 11. EFI SYSTEM OF SQR 472ENGINE
2.29. Three cylinder injector circuit for the power supply circuit (fault code P0268)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_61# pin check cylinder Repair or replace the wire harness
injector connector 2# pin and the ECU line is
broken or the power supply or short circuit to Diagnostic aid
ground.

11-54
 11. EFI SYSTEM OF SQR 472ENGINE
2.30. Four cylinder injector circuit shorted to ground (fault code P0270)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the
ignition switch is in the "ON"
Next step 11
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_23# pin check cylinder Repair or replace the wire harness
injector connector 2# pin and the ECU line is
broken or the power supply or short circuit to Diagnostic aid
ground.

2.31. Four cylinder injector circuit for the power supply circuit (fault code P0271)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint stiffness of injector on wire Yes To step 4
harness, using a multimeter to check the
connector SM1# pin voltage and power for a No Next step
few pieces of value is a 12V.
3 Check in between a cylinder injector Yes Repair or replace the wire harness
connector SM# pin and the main relay line is
No Next step
open circuit or short circuit to ground.
4 Using a multimeter to check a resistor Yes Next step
between the fuel injectors for cylinders No Replace injector
SM1# and SM2# pins at 20 ℃ in 14.5+/-0.5
ohm
5 Whether the 3.7 Ω voltage with a multimeter Yes Diagnostic aid
to check a cylinder injector connector 2# pin
No Next step
and the negative pole of the power supply
will be.
6 Between the X1_23# pin check cylinder Repair or replace the wire harness
injector connector 2# pin and the ECU line is
broken or the power supply or short circuit to Diagnostic aid
ground.

11-55
 11. EFI SYSTEM OF SQR 472ENGINE
2.32. The knock sensor fault (fault code P0325)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument Next step
2 Dial the joint of the knock sensor wire Yes Repair or replace the wire harness
harness, using a multimeter to check the No Next step
connection between 1# 2# and ECUX1_10
X1_54 is short-circuited pin。
3 Dial the joint of the knock sensor wire Yes Repair or replace the wire harness
harness, using a multimeter to check the No Next step
connection between 1# 2# and ECUX1_1
X1_2 is short-circuited pin.
4 The replacement of the knock sensor, check Yes Replace the sensor
whether the fault has disappeared. No Diagnostic aid

2.33. The crankshaft position sensor circuit fault (fault code P0335)
Serial Operation steps Test Next step
number results
1 Ground which is diagnostic instrument, the Next step
ignition switch is in the "OFF"
2 Dial the joint curve position sensor wire Yes Next step
harness, electrical multimeter to check the
No Replace the sensor
sensor 2# and 3# pins between the value at
20 ℃ in 770~950 ohm.
3 Check sensor connector, 2# 3# and ECU Yes Repair or replace the wire harness
X1_29# X1_27# between whether the
circuit breaker or the power supply or short No Next step
circuit to ground. Check the 1# connector
with the main relay output that is between
the X1_27 pin ECU line is broken or the
power supply or short circuit to ground.
4 Check the flywheel signal disc is intact. Yes Diagnostic aid
No Replace the signal disc

11-56
 11. EFI SYSTEM OF SQR 472ENGINE
2.34. The camshaft position sensor fault (fault code P0340)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the
ignition switch is in the "ON"
Next step 11
2 Dial the joint sensor wire harness, using a Yes To step 4
multimeter to check voltage between the 3# No Next step
and 2# pins connector on sensor placement
is around 12V.
3 Check phase sensor 3# pin and 87# pin of Yes Repair or replace the wire harness
the main relay whether the circuit breaker or
open ground; between the X1_30# pin No Next step
check phase sensor 2# pins with the ECU
whether the circuit breaker.
4 If the 9.9V about the value of voltage Yes To step 6
between the X1_72# pin and the negative No Next step
pole of the power supply check phase
sensor connector 1# pin and ECU.
5 Between the X1_72# pin check phase Yes Repair or replace the wire harness
sensor connector 1# pin and the ECU No Next step
whether the circuit breaker.
6 Check the camshaft signal wheel is intact. Yes Diagnostic aid
No Replace the signal disc

2.35. A cylinder ignition coil circuit fault (fault code P0351)

Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint on wire harness for ignition Yes To step 4
coil, using a multimeter to check voltage No Next step
between the 2# pin and the negative pole of
the power supply is 12V.
3 Check the ignition coil between the 2# pin Yes Repair or replace the wire harness
and the 87# pin of main relay circuit is open
circuit or short circuit to ground; No To step 5
4 Between the X1_4# pin check phase sensor Yes Repair or replace the wire harness
and papillary 3# pins and ECU line is open No Next step
circuit or short circuit to ground.
5 Using a multimeter to check the ignition Yes Next step
coil resistance 2# pin and 3# pin between, No Replace ignition coil
stop should be 0.67 +/-10%
6 By using the universal resistance between Yes Diagnostic aid
the table to check the ignition coil 1 No Replace ignition coil
cylinder column and ignition anode, stop
should be 9.2K Ω +/-20%

11-57
 11. EFI SYSTEM OF SQR 472ENGINE
2.36. Two cylinder ignition coil circuit fault (fault code P0352)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint on wire harness for ignition Yes To step 4
coil, using a multimeter to check voltage No Next step
between the 2# pin and the negative pole of
the power supply is 12V.
3 Check the ignition coil between the 2# pin Yes Repair or replace the wire harness
and the 87# pin of main relay circuit is open
circuit or short circuit to ground; No To step 5
4 Between the A31# pin check phase sensor Yes Repair or replace the wire harness
and papillary 1# pins and ECU line is open No Next step
circuit or short circuit to ground.
5 Using a multimeter to check the ignition Yes Next step
coil resistance 1# pin and 2# pin between, No Replace ignition coil
stop should be 0.67 +/-10%
6 By using the universal resistance between Yes Diagnostic aid
the table to check the ignition coil 2 No Replace ignition coil
cylinder column and ignition anode, stop
should be 9.2K Ω +/-20%

2.37. Three cylinder ignition coil circuit fault (fault code P0353)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint on wire harness for ignition Yes To step 4
coil, using a multimeter to check voltage No Next step
between the 2# pin and the negative pole of
the power supply is 12V.
3 Check the ignition coil between the 2# pin Yes Repair or replace the wire harness
and the 87# pin of main relay circuit is open
circuit or short circuit to ground; No To step 5
4 Between the A31# pin check phase sensor Yes Repair or replace the wire harness
and papillary 1# pins and ECU line is open No Next step
circuit or short circuit to ground.
5 Using a multimeter to check the ignition Yes Next step
coil resistance 1# pin and 2# pin between, No Replace ignition coil
stop should be 0.67 +/-10%
6 By using the universal resistance between Yes Diagnostic aid
the table to check the ignition coil 3 No Replace ignition coil
cylinder column and ignition anode, stop
should be 9.2K Ω +/-20%
11-58
 11. EFI SYSTEM OF SQR 472ENGINE
2.38. Four cylinder ignition coil circuit fault (fault code P0354)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step 11
ignition switch is in the "ON"
2 Dial the joint on wire harness for ignition Yes To step 4
coil, using a multimeter to check voltage No Next step
between the 2# pin and the negative pole of
the power supply is 12V.
3 Check the ignition coil between the 2# pin Yes Repair or replace the wire harness
and the 87# pin of main relay circuit is open
circuit or short circuit to ground; No To step 5
4 Between the A32# pin check phase sensor Yes Repair or replace the wire harness
and papillary 3# pins and ECU line is open No Next step
circuit or short circuit to ground.
5 Using a multimeter to check the ignition Yes Next step
coil resistance 2# pin and 3# pin between, No Replace ignition coil
stop should be 0.67 +/-10%
6 By using the universal resistance between Yes Diagnostic aid
the table to check the ignition coil 4 No Replace ignition coil
cylinder column and ignition anode, stop
should be 9.2K Ω +/-20%

2.39. Carbon irrigation control valve (open circuit fault code P0444)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint on wire harness for ignition Yes To step 4
coil, using a multimeter to check voltage No Next step
between the 2# pin and the negative pole of
the power supply is 12V.
3 Check that the carbon canister control valve Yes Repair or replace the wire harness
power supply line is broken or open ground.
No Next step
4 Using a multimeter to check the carbon Yes Next step
canister control resistance between the 1# No Replace the control valve
and 2# pins of the valve value at 20 ℃ is 26
℃
5 Using a multimeter to check the carbon Yes Diagnostic aid
canister control valve street is about 3.7V No Next step
voltage 2# pin and cathode will the house.
6 Between the X1_26# pin to check the Yes Repair or replace the wire harness
carbon canister control valve connector 2# No Diagnostic aid
pin and the ECU whether the circuit
breaker.
11-59
 11. EFI SYSTEM OF SQR 472ENGINE
2.40. Carbon irrigation control valve (short circuit fault code P0445)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step
ignition switch is in the "ON"
2 Dial the joint on wire harness for ignition Yes To step 4
coil, using a multimeter to check voltage No Next step
between the 2# pin and the negative pole of
the power supply is 12V.
3 Check that the carbon canister control valve Yes Repair or replace the wire harness
power supply line is broken or open ground.

No Next step
4 Using a multimeter to check the carbon Yes Next step
canister control resistance between the 1# No Replace the control valve
and 2# pins of the valve value at 20 ℃ is 26
℃
5 Using a multimeter to check the carbon Yes Diagnostic aid
canister control valve street is about 3.7V No Next step
voltage 2# pin and cathode will the house.
6 Between the X1_26# pin to check the carbon Yes Repair or replace the wire harness
canister control valve connector 2# pin and No Diagnostic aid
the ECU whether the circuit breaker.

2.41. The speed sensor is not working properly (fault code P0501)
Serial Operation steps Test Next step
number results
1 round which is diagnostic instrument, the Next step
ignition switch is in the "OFF"
2 If the vehicle equipped with ABS system, Yes Check ABS system
ABS System Pro check whether there is a No Next step
fault code.
3 Check the speed table pointer is working Yes Next step
properly.

No Maintenance instrument line

4 Check whether the normal work of the Yes Next step
vehicle speed sensor. No The replacement of the speed
sensor
5 The X1_39# pin signal line to check the Yes Repair or replace the wire harness
speed sensor and ECU No Next step

11-60
 11. EFI SYSTEM OF SQR 472ENGINE
2.42. Idle speed step motor fault (fault code P0505)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step 11
ignition switch is in the "ON"
2 Dial the idle adjuster connector, electrical Next step
idling regulator of A and D and the B and
The replacement of the stepper
C pins between the value at 20 ℃ is 53 ±
motor
5.3 Ω were examined using a multimeter.
3 Between the check idle adjuster connector Repair or replace the wire harness
A, pin and the D ECU X1_19#, X1_20#
pin, idle adjuster connector B between pin Diagnostic aid
and ECU, C X1_35, X1_36# pin line is
open circuit, short circuit.

2.43. The system voltage fault (fault code P0560)

Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "OFF"
2 using a multimeter to check whether the Yes Next step
battery voltage is about 12V
No Replace the battery
3 The 87# pin check ECU X1_67# and the Yes Repair or replace the wire harness
main relay the line between whether there
is open circuit or short circuit to ground, No Next step
the X1-22# pin and the ignition switch
power supply line is broken or between
the short circuit, X1_44, X1_63 and the
positive pole of the power supply line is
broken or on earth is short.
4 Start the engine, check engine charging Yes Next step
voltage in different speed range is No Changing engine
between 9-16V
5 Check the engine wiring harness ground is Yes Diagnostic aid
good No Repair or replace the wire harness

11-61
 11. EFI SYSTEM OF SQR 472ENGINE
2.44. Internal control (read-only memory) fault (fault code P0605)
Serial Operation steps Test Next step
number results
1 Connect the diagnostic instrument, wait Next step
for 30 seconds or more, to the ignition
switch is in the "ON"
2 Check whether the fault code Yes To step 3
No
3 Switch off ignition, disconnect the Yes The replacement of ECU
battery positive power supply, waiting
for more than 30 seconds, to the ignition No
switch is in the "ON". Check whether
there is a fault code

2.45. Fault display lamp control circuit fault (fault code P0650)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the What's nex
ignition switch is in the "ON"
2 Pulling off the fault lamp connector, pin To step 4
voltage check 1# and dia warm cathode
Next step
will is about 12V
3 Check the main relay power supply Repair or replace the wire harness
circuit, short circuit, open circuit fault
exists. To step 5

4 Check the 2# pin and ECU pin X! _70 Repair or replace the wire harness
association exists between the open circuit What's nex
fault.
5 Check the fault lamp if there is a problem Diagnostic aid
Replace faulty lamp

11-62
 11. EFI SYSTEM OF SQR 472ENGINE
2.46. Air-conditioning evaporator temperature sensor for short circuit or open circuit (power line
fault code P1535)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step 11
ignition switch is in the "ON"
2 The observation data stream in the To step 4
"evaporator temperature", and whether the
Next step
engine temperature quite (numerical and
then temperature.). Note: if the display
value often is constant, that there may be
circuit breaker failure.
3 Check the ECU X1_12# X _!! 2# pins Repair or replace the wire harness
respectively with the line between the
sensor connector a# b# pin is open circuit, Next step
short circuit fault.
4 Start the engine, open space, part load Diagnostic aid
operation. Square diagnostic instrument Replace the sensor
"the evaporator temperature" value
changes, the display values should be with
the engine running down, until the 5
degrees celsius.

2.47. Short circuit on the air conditioning evaporator temperature sensor circuit (fault code P1536)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 The observation data stream in the Yes To step 4
"evaporator temperature", and whether the
No Next step
engine temperature quite (numerical and
then temperature.). Note: if the display
value often is constant, that there may be
circuit breaker failure.
3 Check the ECU X1_12# X _!! 2# pins Yes Repair or replace the wire harness
respectively with the line between the
sensor connector a# b# pin is open circuit, No Next step
short circuit fault.
4 Start the engine, open space, part load Yes Diagnostic aid
operation. Square diagnostic instrument No Replace the sensor
"the evaporator temperature" value
changes, the display values should be with
the engine running down, until the 5
degrees celsius.

11-63
 11. EFI SYSTEM OF SQR 472ENGINE
2.48. Air-conditioning high-voltage switch or air conditioning clutch relay line fault (fault code
P1545)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the fan connectors relay on wire Yes To step 4
harness, multimeter voltage check fan relay
No Next step
connector 85# 86# pin and additional power
between the value is about 12V.
3 Check the fan relay between the 85# pin and Yes Repair or replace the wire harness
the 87# pin of main relay circuit is open
circuit or short circuit to ground; check the No To step 5
fan relay between 86# positive power supply
pin and whether the circuit breaker
4 Check the fan power supply circuit fuse is Yes Repair or replace the wire harness
intact. Check fan relay 87# increased with No Next step
the fan power line is open circuit or short
circuit to ground
Check the fan relay connector 85# between Yes Repair or replace the wire harness
5 pin and ECU X_68# pin line is open circuit No Next step
or short circuit to ground
High voltage switch circuit and the switch to Yes Replace the switch
6 check whether the damage to the air No Diagnostic aid
conditioning compressor

11-64
 11. EFI SYSTEM OF SQR 472ENGINE
2.49. Cooling fan relay line fault (fault code P1624)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the
ignition switch is in the "ON"
Next step
11
2 Dial the fan connectors relay on wire Yes To step 4
harness, multimeter voltage check fan relay
No Next step
connector 85# 86# pin and additional power
between the value is about 12V.
3 Check the fan relay between the 85# pin and Yes Repair or replace the wire harness
the 87# pin of main relay circuit is open
circuit or short circuit to ground; check the No To step 5
fan relay between 86# positive power supply
pin and whether the circuit breaker
4 Check the fan power supply circuit fuse is Yes Repair or replace the wire harness
intact. Check fan relay 87# increased with No Next step
the fan power line is open circuit or short
circuit to ground
Check the fan relay connector 85# between Yes Repair or replace the wire harness
5 pin and ECU X_65# pin line is open circuit No Diagnostic aid
or short circuit to ground

2.50. Air-conditioning compressor fan relay or fan line fault (fault code P1625)
Serial Operation steps Test Next step
number results
1 Connect the diagnosis instrument, the Next step
ignition switch is in the "ON"
2 Dial the fan connectors relay on wire Yes To step 4
harness, multimeter voltage check fan relay
No Next step
connector 85# 86# pin and additional power
between the value is about 12V.
3 Check the fan relay between the 85# pin and Yes Repair or replace the wire harness
the 87# pin of main relay circuit is open
circuit or short circuit to ground; check the No To step 5
fan relay between 86# positive power supply
pin and whether the circuit breaker
4 Check the fan power supply circuit fuse is Yes Repair or replace the wire harness
intact. Check fan relay 87# increased with No Next step
the fan power line is open circuit or short
circuit to ground
Check the fan relay connector 64# between Yes Repair or replace the wire harness
5 pin and ECU X_68# pin line is open circuit No Diagnostic aid
or short circuit to ground

11-65
 11. EFI SYSTEM OF SQR 472ENGINE
3. The fault diagnosis according to the fault phenomena
In this note the fault appears after the preliminary examination
Before starting the engine fault diagnosis according to the fault phenomena should be the first step,
a preliminary inspection:
(1) Confirm the engine fault indicator light work;
(2) Diagnosis instrument for inspection to confirm the absence of fault, fault information record;
(3) Confirmed the existence of fault phenomena of complaints, and confirm that the failure
condition.
Then the visual inspection:
(1) Check whether the fuel pipeline leak;
(2) Check that the vacuum line whether there is fault, kink, the connection is correct;
(3) Check the intake pipeline is blocked, leakage, crushed or damaged;
(4) The high-pressure line check ignition system is broken, aging, ignition sequence is correct;
(5) Check the wiring harness ground is clean, firm;
(6) Check the sensor, actuator connector is loose or poor contact.
Important: if the above phenomenon exists, then the fault phenomenon of repair work, otherwise it
will affect the later
Fault diagnosis and repair work.

3.1. Starting when the engine does not turn or move slowly
General fault location:
1. The battery;
2. Starting motor;
3. Harness or ignition switch;
4. The engine mechanical part.
The general procedure of diagnosis:

11-66
 11. EFI SYSTEM OF SQR 472ENGINE

Serial Operation steps Test Next step

number results
1 Using a multimeter to check the battery
voltage between two terminals, whether the
Yes
No
Next step
Replace the battery
11
voltage of more than 8~12V when the engine
start.
2 The ignition switch is maintained at the start Yes Next step
position, using a multimeter to check
No Repair or replace the wire
whether the terminal to start the motor
harness
positive voltage above 8V.
3 Starting motor disassembly, inspection Yes Repair or replace the starter
starting motor. Focus on examination of motor
whether there is open circuit or due to No Next step
insufficient lubrication card dead.
4 If the failure is occurred in the winter, then Yes The lubricating oil for the
check for engine oil and gear selecting appropriate label
improper lead to start the motor power is too No Next step
large.
Check the engine internal mechanical power Yes Maintenance of internal engine
5 is too large, leading to start the motor does power
not rotate or move slowly No Repeat the above steps

3.2. Starting the engine can drag but failed to start

General fault location:
1. No oil tank;
2. The fuel pump;
3. Speed sensor;
4. The ignition coil;
5. The engine mechanical part.

11-67
 11. EFI SYSTEM OF SQR 472ENGINE
The general procedure of diagnosis:
Serial Operation steps Test Next step
number results
1 Connect the fuel pressure gauge (access Yes Next step
point for the fuel distribution pipe assembly No Maintenance supply coefficient
inlet pipe end), start the engine, check the
fuel pressure in the idling condition is about
380kPa
2 Connect the EFI system diagnostic Yes Next step
instrument, to observe the "engine" of data
No Repair speed sensor circuit
items, start the engine, observe whether
there is a speed signal output.

3 Appropriated the sub-cylinder line a Yes Next step

cylinder which is connected to, spark plug,
spark plug electrode distance engine body No Maintenance of the ignition
around 5mm, start the engine, check system
whether there is a blue and white high
pressure fire

4 Check the engine cylinder pressure of each Yes Exclusion of unloading failure
engine cylinder pressure, observe whether of engine
the lack of No Next step

Check the X1-1# X1-2# pin on the iron is Yes Diagnostic aid
5 normal No Maintenance of the
corresponding line

3.3. Hot starting difficulty

General fault location:
1. The fuel moisture content;
2. The fuel pump;
3. The coolant temperature sensor;
4. The fuel pressure regulator vacuum tube;
5. The ignition coil.

11-68
 11. EFI SYSTEM OF SQR 472ENGINE
The general procedure of diagnosis:
Serial Operation steps Test Next step
number results
1 Connect the fuel pressure gauge (access Yes Next step 11
point for the fuel distribution pipe assembly No Maintenance supply coefficient
inlet pipe end), start the engine, check the
fuel pressure in the idling condition is about
380kPa
2 Appropriated the sub-cylinder line a Yes Next step
cylinder which is connected to, spark plug,
No Maintenance of the ignition
spark plug electrode distance engine body
system
around 5mm, start the engine, check
whether there is a blue and white high
pressure fire
3 Pulling off the coolant temperature sensor Yes Repair or replace the sensor line
connector, start the engine, when the engine
is started successfully observed. (a 300 ohm No Next step
resistor in series or in the coolant
temperature sensor connector to replace
coolant sensor, observation of the engine is
successful start)
4 Check the fuel pressure regulator vacuum Yes Repair or replace
tube whether there is loose or leakage No Next step
phenomenon.
Check the fuel situation, observe whether Yes Replace fuel
5 the failure phenomenon was caused due to No Next step
gas.
Check the X1_1# X1_2# pin on the iron is Yes Diagnostic aid
6 normal. No Maintenance of the
corresponding line

3.4. Cold vehicle starting difficulty

General fault location:
1. The fuel moisture content;
2. The fuel pump;
3. The coolant temperature sensor;
4. The fuel injector;

11-69
 11. EFI SYSTEM OF SQR 472ENGINE
5. The ignition coil;
6. Solar term door body and idle bypass airway;
7. The engine mechanical part.

The general procedure of diagnosis:

Serial Operation steps Test Next step
number results
1 Connect the fuel pressure gauge (access Yes Next step
point for the fuel distribution pipe assembly No Maintenance of oil supply system
inlet pipe end), start the engine, check the
fuel pressure in the idling condition is about
3800kPa
2 Set aside seven minutes a cylinder cylinder Yes Next step
line, connected to the spark plug, spark
machine from the engine body around No Maintenance of the ignition
5mm, start the engine, check whether there system
is a blue and white high pressure fire
3 Pulling off the coolant temperature sensor Yes Repair or replace the sensor line
connector, start the engine, the engine is
successful up observation. （ Or a 2500 No Next step
OHM Series in the coolant temperature
sensor junction resistance to replace the
coolant temperature sensor, observation of
the engine is successful.）
4 Gently down on the accelerator, observe Yes Cleaning solar term door and idle
whether easy to start airway
No Next step
Remove the injector, injector clogging with Yes Failure to replace
5 special cleaning analyzer check whether the No Next step
injector is there is a leak, or in.

Check the fuel situation, observe whether Yes Replace fuel

6 the fault now just gas caused by.
No Next step

Check the engine cylinder pressure of each Yes Remove engine mechanical fault
7 engine cylinder pressure, observe whether No Next step
there is insufficient.
Check the X1+! # X1_2# pin on iron is Yes Diagnostic aid
normal.
8
No Maintenance of the corresponding
line

3.5. Speed normal, any time starting difficulty

General fault location:
1. The fuel moisture content; 2, The fuel pump; 3. Coolant temperature sensor. 4. Injector; 5.
Ignition coil; 6. Solar term door body and idle bypass airway. 7. Inlet; 8. The ignition timing; 9.
Spark plug. 10. The engine mechanical part.

11-70
 11. EFI SYSTEM OF SQR 472ENGINE
The general procedure of diagnosis:
Serial Operation steps Test Next step
number results
1 Check the air filter is clogged, the intake Yes Maintenance of air intake
11
pipe is leaking system
No Next step
2 Connect the fuel pressure gauge (access Yes Next step
point for the fuel distribution pipe assembly
inlet pipe end), start the engine, check the No Maintenance of oil supply
fuel pressure in the idling condition is about system
38kPa
3 Appropriated the sub-cylinder line a Yes Next step
cylinder which is connected to, spark plug,
spark plug electrode distance of engine is No Maintenance of the ignition
about 5mm, the starting engine, check system
whether there is a blue and white high
pressure fire
4 Check the cylinder spark plug, the period of Yes Next step
observation model and gap four No Adjust or replace
conformance to specification.
Pulling off the coolant temperature sensor Yes Repair or replace the sensor line
5 connector, start the engine, the engine is No Next step
starting to observe
Check the fuel situation, observe whether Cleaning solar term door and
6 the fault now just gas caused by. idle airway
Next step
Gently down on the accelerator, observe Failure to replace
7
whether easy to start. Next step
Check the fuel situation, observe whether Replace fuel
8 the failure phenomenon was caused due to Next step
gas
Check the engine cylinder pressure of each Remove engine mechanical fault
9 engine cylinder pressure, observe whether Next step
there is insufficient
Check the ignition sequence engine and Next step
10 ignition timing meets the specifications Maintenance of the ignition
timing
Check the X1_1# X1_2# pin ground is Diagnostic aid
11 normal Maintenance of the
corresponding line

3.6. Start normal, but any time idling instability

General fault location:
1. The fuel moisture content;
2. The fuel injector;
11-71
 11. EFI SYSTEM OF SQR 472ENGINE
3. The spark plug;
4. Solar term door body and idle bypass airway;
5. The inlet;
6. Idle speed regulator;
7. The ignition timing;
8. The spark plug;
9. The engine mechanical part.

The general procedure of diagnosis

Serial Operation steps Test Next step
number results
1 Check the air filter is clogged, the intake Yes Check the intake system
pipe is leaking No Next step

2 Check whether the card idle speed regulator Yes Clean or replace
No Next step
3 Check the cylinder spark plug, observe its Yes Next step
model and gap meets the specifications
No Adjust or replace
4 Check the solar term door body and idle Yes Clean
speed organ exists the phenomenon of No Next step
carbon deposition
Remove the injector, injector with special Yes Failure to replace
cleaning analyzer to check whether the No Next step
5
injector is there is a leak, plugging or flow
ultra difference phenomenon
Check the fuel situation, observe whether Yes Replace fuel
6 the failure phenomenon was caused due to No Next step
gas
Check the engine cylinder pressure of each Yes Remove engine mechanical fault
7 engine cylinder pressure, observe whether No Next step
there are differences in the larger
Compliance with the specification when Yes Next step
8 ignition ignition sequence checking engine. No Maintenance of the ignition
timing
Check the X1_1# X1_1# pin on the iron is Yes Diagnostic aid
9 normal No Maintenance of the
corresponding line

3.7. Start, warm-up process unstable idle speed

General fault location:
1. The fuel moisture content;
2. The coolant temperature sensor;
3. The spark plug;

11-72
 11. EFI SYSTEM OF SQR 472ENGINE
4. Solar term door body and idle bypass airway;
5. The inlet;
6. Idle speed regulator;
7. The engine mechanical part.
11

The general procedure of diagnosis:

Serial Operation steps Test Next step
number results
1 Check the air filter is clogged, the intake Yes Check the intake system
pipe is leaking No Next step

2 Check whether the card idle speed regulator Yes Next step
No Adjust or replace
3 Check the cylinder spark plug, observe its Yes Cleaning of parts
model and gap meets the specifications
No Next step
4 Check the solar term door body and idle Yes Trim lines or replacement of the
speed organ exists the phenomenon of sensor
carbon deposition No Next step
Remove the injector, injector with special Yes Failure to replace
cleaning analyzer to check whether the No Next step
5
injector is there is a leak, plugging or flow
ultra difference phenomenon
Check the fuel situation, observe whether Yes Replace fuel
6 the failure phenomenon was caused due to No Next step
gas
Check the engine cylinder pressure of each Yes Remove engine mechanical fault
7 engine cylinder pressure, observe whether No Next step
there are differences in the larger
Compliance with the specification when Yes Next step
8 ignition ignition sequence checking engine. No Maintenance of the ignition
timing
Check the X1_1# X1_1# pin on the iron is Yes Diagnostic aid
9 normal No Maintenance of the
corresponding line

3.8. Start, warm-up after idling instability

General fault location:
1. The fuel moisture content;
2. The coolant temperature sensor;

11-73
 11. EFI SYSTEM OF SQR 472ENGINE
3. The spark plug;
4. Solar term door body and idle bypass airway;
5. The inlet;
6. Idle speed regulator;
7. The engine mechanical part.

The general procedure of diagnosis:

Serial Operation steps Test Next step
number results
1 Check the air filter is clogged, the intake Yes Check the intake system
pipe is leaking No Next step

2 Check whether the card idle speed regulator Yes Clean or replace
No Next step
3 Check the cylinder spark plug, observe its Yes Next step
model and gap meets the specifications
No Adjust or replace
4 Check the solar term door body and idle Yes Clean
speed organ exists the phenomenon of No Next step
carbon deposition
Remove the injector, injector with special Yes Failure to replace
cleaning analyzer to check whether the No Next step
5
injector is there is a leak, plugging or flow
ultra difference phenomenon
Check the fuel situation, observe whether Yes Replace fuel
6 the failure phenomenon was caused due to No Next step
gas
Check the engine cylinder pressure of each Yes Remove engine mechanical fault
7 engine cylinder pressure, observe whether No Next step
there are differences in the larger
Compliance with the specification when Yes Next step
8 ignition ignition sequence checking engine. No Maintenance of the ignition
timing
Check the X1_1# X1_1# pin on the iron is Yes Diagnostic aid
9 normal No Maintenance of the
corresponding line

3.9. Normal starting, part load (such as: air conditioning) when idling instability or flameout
General fault location:
1. Air-conditioning system;

11-74
 11. EFI SYSTEM OF SQR 472ENGINE
2. Idle speed regulator;
3. The fuel injector.

11
The general procedure of diagnosis:
Serial Operation steps Test Next step
number results
1 Remove the idle adjuster, check the solar Yes Cleaning of parts
term door body, idle speed and idle bypass No Next step
airway carbon deposition
2 Observation on the output power of the Yes To step 4
engine is increased when the air
No Next step
conditioning, the phenomenon of EFI
system diagnosis instrument of ignition
advance angle, injection pulse width and air
conditioning, wiring harness end is a high
level signal.
3 Disconnect the electrical control unit Yes Next step
X1_68# pin connecting line, check the open
air conditioning, wiring harness end is a No Maintenance of air-conditioning
high level signal. system
4 Check system pressure, air conditioning Yes Next step
compressor electromagnetic clutch and the No Maintenance of air-conditioning
air conditioning compressor pump is system
normal
Remove the injector, injector with special Yes Failure to replace
cleaning analyzer check whether the No Next step
5
injector is there is a leak, plugging or flow
ultra difference phenomenon
Yes Diagnostic aid
Check the X1_1# X1_2# pin on the iron is
6 No Maintenance of the
normal
corresponding line

3.10. Normal starting, idle speed is too high

General fault location:

11-75
 11. EFI SYSTEM OF SQR 472ENGINE
1. Solar term door body and idle bypass airway;
2. The vacuum tube;
3. Idle speed regulator;
4. The coolant temperature sensor;
5. The ignition timing.

The general procedure of diagnosis:

Serial Operation steps Test Next step
number results
1 Check the throttle cable is stuck or Yes Adjustment
too tight No Next step

2 Check the intake system and Yes Maintenance of air intake system
vacuum pipe connection whether
No Next step
there is leakage
3 Remove the idle adjuster, solar term Yes Cleaning of parts
door body check, idle speed
regulator and idle speed was the No Next step
existence of the phenomenon of
carbon deposition in the airway
4 Pulling off the coolant temperature Yes Repair or replace the sensor line
sensor connector, start the engine, No Next step
when the engine is idling too high
observation
Check the engine ignition timing Yes Next step
5
meets the specifications No Maintenance of the ignition timing
Check the X1_1# X1_2# pin on the Yes Diagnostic aid
6
iron is normal No Maintenance of the corresponding line

11-76
 11. EFI SYSTEM OF SQR 472ENGINE
3.11. Accelerate the speed to go up not to go or stop
General fault location:
1. The fuel moisture content;
2. The intake pressure sensor and solar term door position sensor;
3. The spark plug;
4. Solar term door body and idle bypass airway;
11
5. The inlet;
6. Idle speed regulator;
7. The fuel injector;
8. The ignition timing;
9. The exhaust pipe.

The general procedure of diagnosis:

Serial Operation steps Test Next step
number results
1 Check the air filter is clogged Yes Maintenance of air intake system
No Next step
2 Connect the fuel pressure gauge Yes Next step
(access point for the fuel
distribution pipe assembly inlet pipe No Maintenance of oil supply system
end), start the engine, check the fuel
pressure in the idling condition is
about 390kPa
3 Check the cylinder spark plug, Yes Next step
observe its model and gap meets the
specifications No Adjust or replace
4 Remove the idle adjuster, check the Yes Cleaning of parts
solar term door body, idle speed No Next step
regulator and idling bypass airway
carbon deposition.
Check the intake pressure sensor, Yes Next step
5 solar term door position sensor and No Repair or replace the sensor line
think you are normal.
Remove the injector, injector with Yes Failure to replace
special cleaning analyzer check
6 No Next step
whether the injector is there is a leak
or blockage
Check the fuel situation, in order to Yes Failure to replace
7 observe the phenomena of four No Next step
since just after refueling cause
Check the ignition sequence engine Yes Next step
8 and ignition timing meets the No Maintenance of the ignition timing
specifications
Check whether the smooth air Yes Next step
9
exhaust pipe No Repair or replace the exhaust pipe
Check the X1_1# X1_2# pin on the Yes Diagnostic aid
10 iron is normal
No Maintenance of the corresponding line

11-77
 11. EFI SYSTEM OF SQR 472ENGINE
3.12. Accelerating the slow response
General fault location:
1. The fuel moisture content;
2. The intake pressure sensor and solar term door position sensor;
3. The spark plug;
4. Solar term door body and idle bypass airway;
5. The inlet;
6. Idle speed regulator;
7. The fuel injector;
8. The ignition timing;
9. The exhaust pipe.

The general procedure of diagnosis:

Serial Operation steps Test Next step
number results
1 Check the air filter is clogged Yes Maintenance of air intake system
No Next step

2 Connect the fuel pressure gauge Yes Next step

(access point for the fuel
distribution pipe assembly inlet pipe No Maintenance of oil supply system
end), start the engine, check the fuel
pressure in the idle condition is
about 380kPa
3 Check the cylinder spark plug, Yes Next step
observe its model and gap meets the
specification No Adjust or replace
4 Remove the idle adjuster, check the Yes Cleaning of parts
solar term door body, idle speed No Next step
regulator and idling bypass airway
carbon deposition.
Check the intake pressure sensor, Yes Next step
5 solar term door position sensor and No Repair or replace the sensor line
think you are normal.
Remove the injector, injector with Yes Failure to replace
special cleaning analyzer check
6 No Next step
whether the injector is there is a leak
or blockage
Check the fuel situation, in order to Yes Failure to replace
7 observe the phenomena of four No Next step
since just after refueling cause
Check the ignition sequence engine Yes Next step
8 and ignition timing meets the No Maintenance of the ignition timing
specifications
Check whether the smooth air Yes Next step
9
exhaust pipe No Repair or replace the exhaust pipe
Check the X1_1# X1_2# pin on the Yes Diagnostic aid
10 iron is normal
No Maintenance of the corresponding line

11-78
 11. EFI SYSTEM OF SQR 472ENGINE
3.13. Accelerating weakness, poor performance
General failure position:
1. Fuel moisture content; 2. The intake pressure sensor and solar term door position sensor;
3. Spark plug; 4. The ignition coil; 5. Solar term door body and idle bypass airway;
6. Inlet; 7. Idle speed regulator; 8. Injector; 9. The ignition timing; 10. The exhaust pipe.
11
The general procedure of diagnosis:
Serial Operation steps Test Next step
number results
1 Check the clutch slip, the tire Yes Repair
pressure is low, the brake drag, the No Next step
tire size is incorrect, four wheel
positioning is not correct faults.
2 Check the air filter is clogged. Yes Maintenance of air intake system
No Next step
3 Connect the fuel pressure gauge Yes Next step
(access point for the fuel No Maintenance of oil supply system
distribution pipe assembly inlet pipe
end), start the engine, check the fuel
pressure in the idling condition is
about 38kPa.
4 Set aside money in a cylinder of the Yes Next step
cylinder, connected to the spark
plug, the spark plug electrode No Maintenance of the ignition system
distance engine body around 5mm,
start the engine, check the
high-pressure fire intensity is
normal.
Check the cylinder spark plug, Yes Next step
5 observe its model and gap whether No Adjust or replace
payment specification.
Remove the idle adjuster, check the Yes Cleaning of parts
6 solar term door body, idle speed
regulator and idling on airway No Next step
carbon deposition
Check the intake pressure sensor, Yes Next step
7 solar term door position sensor and
its circuit is normal No Repair or replace the sensor line

Remove the injector, injector with Yes Failure to replace

8 special cleaning analyzer check No Next step
whether the injector is there is a leak
or blockage.
Check the fuel situation, observe Yes Replace fuel
9 whether the failure phenomenon No Next step
was caused due to gas
Check the engine ignition is Xu and Yes Next step
10 ignition timing specification
compliance No Maintenance of the ignition timing

Check whether the smooth air Next step

11 exhaust pipe Repair or replace the exhaust pipe
Check the X1_1# X1_2# pin on the Diagnostic aid
12 iron is normal Maintenance of the corresponding line

11-79
 12. LIGHTING AND SWITCHES

Overhaul Info……………………12-1 Horn…………………………………… 12-8

Troubleshooting…………………12-2
Replacing bulbs…………………12-3
headlight…………………………12-5
Ignition Switch…………………..12-5
Combined switch………………..12-6
Brake Light Switch……………….12-8

Overhaul Information

Warning
● Headlight bulb will be very hot when it is turned on. Do not touch it after it is just turned off.
Operation should be done when the bulb is cooled down.
● Inspection of water temperature alarm may use fire source and liquid of high temperature. Do
not put flammable matters nearby and take care not to get burnt.
● The temperature of headlight is quite high when turned on. Replacing with bare hand or stained
glove will cause oil stains on the glass face which may form hot spot and cause deformation of
glass face and damage to bulb.
● Pay attention to the following when replacing the bulb.
—Do not replace the bulb when it is turned on. Keep ignition switch in the OFF position, and
replace after the bulb is cooled down.
—Replace the bulb with hands in clean gloves to avoid oil stains on the glass surface.
—Clean the glass with a clean rag dipped in alcohol or isoamyl acetate in case of any oil stains
on the glass surface.
● If the Inspection has to be done with battery, check if the battery is normal.
● Inspection of switch continuity can be done without removing the switches from the vehicle.
● After the inspecting and overhauling of each part, cables and wires should be routed properly
(chapter 1) Refer to Chapter 2 for removal and installation of taillight and rear turning lights.

Overhaul Standard

Item Standard
Mail switch fuse 30A
Fuse
Sub-fuse 10A 20A 30A
Head lamp 12 V 55 W× 2
Headlight Front position lamp 12 V 5 W
Front direction indicator 12 V 1.6 W (15*LED)
Light, bulb
Stop lamp 12 V 1.8 W (12*LED)
Brake light
Rear position lamp 12 V 0.2 W (12*LED)
/Tail light
Rear direction indicator 12 V 2 W (15*LED)

12-1
 12. LIGHTING AND SWITCHES

TROUBLESHOOTING
12
Head Light Cannot Turn On
● Broken fuse
● Open circuit with main cable
● Burnt Bulb
● Faulty Switch

12-2
 12. LIGHTING AND SWITCHES

Replacing Bulb
Headlight Bulb
Headlight bulb will be very hot when it is turned on.
Do not touch it after it is just turned off.
Operation should be done when the bulb is cooled
down.

Remove headlight(→13-5）

Disconnect headlight.

Remove dust-proof cap, headlight connector, circlip

and replace with a new bulb.

Warning:
● Wear clean gloves when replacing bulb.
● Oil stains on the glass surface may cause
break of bulb. Clean the stained surface
with alcohol or isoamyl acetate.
● Be sure to hold the socket firmly when
removing the bulb. Never pull the lead,
otherwise it may be pulled out of the
terminal in the coupler.

Head lamp: 12 V 55 W× 2
Front position lamp：12 V 5 W
Reverse the removal procedure for installation
After replacing the bulb, adjust headlight beam.

Inspection of Headlight
Turn the ignition switch to ON position, turn light
switch to the illuminating position and check if the
headlight is on.
-ON: Normal
-Still off: short circuit of main cable or broken main cable.

12-3
 12. LIGHTING AND SWITCHES

Front Turning Indicator Bulbs

Remove headlight. (→13-5) 12
Remove cover of headlight.
Replace front turning Indicator bulbs.

Front direction indicator: 12 V 1.6 W (15*LED)

Brake Light/Tail Light Bulb

Remove rear corner cover, cargo box. (→2-13)
Remove 3 nuts,
Remove taillight cover.
Replace brake light/tail light bulb
Bulb Specification:
Stop lamp: 12 V 1.8 W (12*LED)
Rear position lamp: 12 V 0.2 W (12*LED)
Reverse the removal procedure for installation.

Rear Turning Indicator Bulbs

Remove taillight (→12-4)

Remove taillight cover.
Replace rear turning indicator bulbs.
Bulb Specification: 12 V 2 W (15*LED)
Reverse the removal procedure for installation.

12-4
 12. LIGHTING AND SWITCHES

Headlight
Remove:
—Front air guide cover assy (→2-10)
—4 fixing bolts of headlight.
—Headlight
—Fixed bolt headlight, headlight connector,
Headlight

Reverse the removal procedure for installation.

Note:
Be careful not to damage main cable when
assembling.
After replacing, adjust the headlight beam.

Note
Main cables and wires should be routed
properly.

Ignition Switch
Inspection
Remove front cover (→2-11)

Disconnect 4P connector of ignition switch.

12-5
 12. LIGHTING AND SWITCHES

Check according to the following table if the

connector terminals are in continuity. 12

Remove:

Remove meter panel (→2-11)

Disconnect 4P connector of ignition switch

Reverse the removal procedure for installation

Combined Switch
Remove front cover (→2-11)
Remove meter panel (→2-11)
Disconnect connector of combined switch
Check according to the following table if the
connector terminals are in continuity.

12-6
 12. LIGHTING AND SWITCHES

2WD、4WD、4WD Diff-Lock Switch

No continuity: Change the switch.

12-7
 12. LIGHTING AND SWITCHES

Brake Light Switch

12
Disconnect brake light switch connector and
check terminators for continuity.
Hold the brake pedal——Brake lights are open.
Release the brake pedal—Brake light is off.

When hold the brake pedal, the brake light

is off:
Replace brake pump assembly.

Horn
Inspection:

Remove bolt.
Remove horn connector.
Connect with a fully charged 12V battery and check
the horn sounds.
Faulty Horn: →Replace

12-8