Technical data sheet SFA-S2
Rotary actuator fail-safe for adjusting
dampers in technical building installations
• Air damper size up to approx. 4 m²
• Torque motor 20 Nm
• Nominal voltage AC 24...240 V /
DC 24...125 V
• Control Open/close
• with 2 integrated auxiliary switches
Technical data
Electrical data Nominal voltage AC 24...240 V / DC 24...125 V
Nominal voltage frequency 50/60 Hz
Nominal voltage range AC 19.2...264 V / DC 21.6...137.5 V
Power consumption in operation 7W
Power consumption in rest position 3.5 W
Power consumption for wire sizing 18 VA
Auxiliary switch 2 x SPDT, 1 x 10% / 1 x 11...100%
Switching capacity auxiliary switch 1 mA...3 A (0.5 A inductive), DC 5 V...AC 250 V
Connection supply / control Cable 1 m, 2 x 0.75 mm²
Connection auxiliary switch Cable 1 m, 6 x 0.75 mm²
Parallel operation Yes (note the performance data)
Functional data Torque motor 20 Nm
Torque fail-safe 20 Nm
Direction of motion motor selectable by mounting L/R
Direction of motion fail-safe selectable by mounting L/R
Manual override by means of hand crank and locking switch
Angle of rotation Max. 95°
Angle of rotation note can be limited by adjustable mechanical end
stop
Running time motor 75 s / 90°
Running time fail-safe <20 s @ -20...50°C / <60 s @ -30°C
Sound power level, motor 45 dB(A)
Mechanical interface Universal shaft clamp 10...25.4 mm
Position indication Mechanical
Service life Min. 60'000 fail-safe positions
Safety data Protection class IEC/EN II, reinforced insulation
Protection class UL II, reinforced insulation
Protection class auxiliary switch IEC/EN II, reinforced insulation
Degree of protection IEC/EN IP54
Degree of protection NEMA/UL NEMA 2
Enclosure UL Enclosure Type 2
EMC CE according to 2014/30/EU
Low voltage directive CE according to 2014/35/EU
Certification IEC/EN IEC/EN 60730-1 and IEC/EN 60730-2-14
UL Approval cULus according to UL60730-1A, UL60730-2-14
and CAN/CSA E60730-1
The UL marking on the actuator depends on
the production site, the device is UL-compliant
in any case
Type of action Type 1.AA.B
www.belimo.com SFA-S2 • en-gb • 2022-12-06 • Subject to change 1/4
Technical data sheet SFA-S2
Safety data Rated impulse voltage supply / control 4 kV
Rated impulse voltage auxiliary switch 2.5 kV
Pollution degree 3
Ambient humidity Max. 95% RH, non-condensing
Ambient temperature -30...50°C [-22...122°F]
Storage temperature -40...80°C [-40...176°F]
Servicing maintenance-free
Weight Weight 2.3 kg
Safety notes
• This device has been designed for use in stationary heating, ventilation and air-conditioning
systems and must not be used outside the specified field of application, especially in aircraft or
in any other airborne means of transport.
• Outdoor application: only possible in case that no (sea) water, snow, ice, insolation or
aggressive gases interfere directly with the device and that it is ensured that the ambient
conditions remain within the thresholds according to the data sheet at any time.
• Caution: Power supply voltage!
• Only authorised specialists may carry out installation. All applicable legal or institutional
installation regulations must be complied during installation.
• The device may only be opened at the manufacturer's site. It does not contain any parts that
can be replaced or repaired by the user.
• Cables must not be removed from the device.
• To calculate the torque required, the specifications supplied by the damper manufacturers
concerning the cross-section, the design, the installation situation and the ventilation
conditions must be observed.
• The two switches integrated in the actuator are to be operated either on power supply voltage
or at safety extra-low voltage. The combination power supply voltage/safety extra-low voltage
is not permitted.
• The device contains electrical and electronic components and must not be disposed of as
household refuse. All locally valid regulations and requirements must be observed.
Product features
Mode of operation The actuator is equipped with a universal power supply module that can utilise supply voltages
of AC 24...240 V and DC 24...125V.
The actuator moves the damper to the operating position at the same time as tensioning the
return spring. The damper is turned back to the fail-safe position by spring force when the
supply voltage is interrupted.
Simple direct mounting Simple direct mounting on the damper shaft with a universal shaft clamp, supplied with an anti-
rotation device to prevent the actuator from rotating.
Manual override By using the hand crank the damper can be actuated manually and engaged with the locking
switch at any position. Unlocking is carried out manually or automatically by applying the
operating voltage.
Adjustable angle of rotation Adjustable angle of rotation with mechanical end stops.
High functional reliability The actuator is overload protected, requires no limit switches and automatically stops when the
end stop is reached.
Flexible signalling The actuator has one auxiliary switch with a fixed setting and one adjustable auxiliary switch.
They permit a 10% or 11...100% angle of rotation to be signaled.
Accessories
Electrical accessories Description Type
Auxiliary switch 2 x SPDT S2A-F
Feedback potentiometer 200 Ω P200A-F
Feedback potentiometer 1 kΩ P1000A-F
www.belimo.com SFA-S2 • en-gb • 2022-12-06 • Subject to change 2/4
Technical data sheet SFA-S2
Mechanical accessories Description Type
Shaft extension 240 mm Ø20 mm for damper shaft Ø 8...22.7 mm AV8-25
End stop indicator IND-AFB
Shaft clamp reversible, for central mounting, for damper shafts Ø12.7 / K7-2
19.0 / 25.4 mm
Ball joint suitable for damper crank arm KH8 / KH10, Multipack 10 pcs. KG10A
Ball joint suitable for damper crank arm KH8, Multipack 10 pcs. KG8
Damper crank arm Slot width 8.2 mm, clamping range Ø10...18 mm KH8
Actuator arm, for 3/4" shafts, clamping range Ø10...22 mm, Slot width 8.2 KH-AFB
mm
Form fit insert 10x10 mm, Multipack 20 pcs. ZF10-NSA-F
Form fit insert 12x12 mm, Multipack 20 pcs. ZF12-NSA-F
Form fit insert 15x15 mm, Multipack 20 pcs. ZF15-NSA-F
Form fit insert 16x16 mm, Multipack 20 pcs. ZF16-NSA-F
Mounting kit for linkage operation for flat and side installation ZG-AFB
Base plate extension Z-SF
Anti-rotation mechanism 230 mm, Multipack 20 pcs. Z-ARS230L
Hand crank 63 mm ZKN2-B
Electrical installation
Caution: Power supply voltage!
Parallel connection of other actuators possible. Observe the performance data.
Wire colours:
1 = blue
2 = brown
S1 = violet
S2 = red
S3 = white
S4 = orange
S5 = pink
S6 = grey
Wiring diagrams
AC 24...240 V / DC 24...125 V, open/ Auxiliary switch
close
www.belimo.com SFA-S2 • en-gb • 2022-12-06 • Subject to change 3/4
Technical data sheet SFA-S2
Operating controls and indicators
Auxiliary switch settings
Note: Perform settings on the actuator only in deenergised state.
For the auxiliary switch position settings, carry out points 1 to 7 successively.
1 Manual override
Turn the hand crank until the desired switching position is set.
2 Shaft clamp
Edge line A displays the desired switching position of the actuator on the scale.
3 Fasten the locking device
Turn the locking switch to the „Locked padlock“ symbol.
4 Auxiliary switch
Turn rotary knob until the notch points to the arrow symbol.
5 Unlock the locking device
Turn the locking switch to the „Unlocked padlock“ symbol or unlock with the hand
crank.
6 Cable
Connect continuity tester to S4 + S5 or to S4 + S6.
7 Manual override
Turn the hand crank until the desired switching position is set and check whether the
continuity tester shows the switching point.
Dimensions
Spindle length
Min. 85
Min. 15
Clamping range
www.belimo.com SFA-S2 • en-gb • 2022-12-06 • Subject to change 4/4
