CHECKING OLT UPTIME

OL01#display sysuptime
System up time: 324 day 20 hour 55 minute 38 second

CHECKING OLT BOARD

OL01#display board 0
————————————————————————-
SlotID  BoardName  Status          SubType0 SubType1    Online/Offline
————————————————————————-
0
1       H805GPFD   Normal
2       H805GPFD   Normal
3       H805GPFD   Normal
4       H805GPFD   Normal
5       H805GPFD   Normal
6       H805GPFD   Normal
7       H802SCUN   Active_normal             –> Control Module   

8       H802SCUN   Standby_normal          –> Control Module   

9       H805GPFD   Normal

10      H805GPFD   Normal
11      H805GPFD   Normal
12      H805GPFD   Normal
13      H805GPFD   Normal
14      H805GPFD   Normal
15      H805GPFD   Normal
16      H805GPFD   Normal
17      H801X2CS   Normal               –> Uplink Module   

18      H801X2CS   Normal               –> Uplink Module

19      H801PRTE   Normal

20      H801PRTE   Normal
————————————————————————-
OL01#

CHECKING OLT PROCESSOR AND MEMORY PER SLOT

OL01#display mem 0/1
Memory occupancy: 33%

OL01#display cpu 0/1

Send message for inquiring board cpu occupancy successfully, board
executing…
CPU occupancy: 15%
OL01#

CHECKING OLT TEMPERATURE

OL01#display temperature 0
SlotID:  1      BoardName: H805      Temperature:   42C( 107F)
SlotID:  2      BoardName: H805       Temperature:   41C( 105F

FINDING ONT BY SN NUMBER

OL01#display ont info by-sn ABCDEF
—————————————————————————–

In Huawei port 1 = port 0 at system

F/S/P                   : 0/1/0 (remember) this ONT Meaning that locate at slot 1
port 0 onu id 2

ONT-ID                  : 2
Control flag            : active
Run state               : offline
Config state            : initial
Match state             : initial
DBA type                : SR
ONT distance(m)         : –
ONT battery state       : –
Memory occupation       : –
CPU occupation          : –
Temperature             : –
Authentic type          : SN-auth
SN                      : ABCDEF (HWTC-07930A53)
Management mode         : OMCI
Software work mode      : normal
Isolation state         : normal
ONT IP 0 address/mask   : –
Description             : IRONMAN
Last down cause         : dying-gasp –> down caused by dying gasp (dying-
gasp = ont off )

Last up time            : 2016-11-11 17:52:08+07:00 –> Log Last Uptime

Last down time          : 2016-11-15 09:23:27+07:00

Last dying gasp time    : 2016-11-15 09:23:27+07:00
ONT online duration     : –
Type C support          : Not support
Interoperability-mode   : Unknown

CHECKING ONT STATUS

OL01#display ont info 0 1 0 all
—————————————————————————–
F/S/P   ONT         SN         Control     Run      Config   Match    Protect
ID                     flag        state    state    state    side
—————————————————————————–
0/ 1/0    1  ABCDEF  deactivated offline  initial  initial  no
0/ 1/0    2  REZABU  active      offline  initial  initial  no —
0/ 1/0    4  BAREZU  active      online   normal   match    no  –> ONT online

CHECKING ONT HISTORY LOGS

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#display ont register-info 0 1
——————————————————————————
Index               : 10
Auth-type           : SN-auth
SN                  : ABCDEF (HWTC-19698F53)
TYPE                : 245H
UpTime              : 2016-11-02 16:56:37+07:00
DownTime            : 2016-11-04 07:52:15+07:00
DownCause           : ONT dying-gasp
——————————————————————————
Index               : 9
Auth-type           : SN-auth
SN                  : ABCDEF (HWTC-19698F53)
TYPE                : 245H
UpTime              : 2016-10-31 22:29:05+07:00
DownTime            : 2016-11-02 16:42:36+07:00
DownCause           : ONT dying-gasp
——————————————————————————
Index               : 8
Auth-type           : SN-auth
SN                  : ABCDEF (HWTC-19698F53)
TYPE                : 245H
UpTime              : 2016-10-29 00:25:35+07:00
DownTime            : 2016-10-31 22:13:03+07:00
DownCause           : ONT dying-gasp

CHECKING ONT MAC ADDRESS

OL01#display mac-address port 0/1/0 ont 2
———————————————————————–
SRV-P BUNDLE TYPE MAC            MAC TYPE F /S /P   VPI  VCI   VLAN
ID
INDEX INDEX
———————————————————————–
2389     –  gpon aaaa-bbbb-cccc dynamic  0 /1 /0   2    2         122
2388     –  gpon bbbb-aaaa-cccc dynamic  0 /1 /0   2    1         212
———————————————————————–
Total: 2
Note: F–Frame, S–Slot, P–Port, F/S/P indicates PW Index for PW,
A–The MAC address is learned or configured on the aggregation port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,
v/e–vlan/encap, pritag–priority-tagged,
ppp–pppoe, ip–ipoe, ip4–ipv4oe, ip6–ipv6oe

OL01#

CHECKING ONT POWER

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#display ont optical-info 0 all
—————————————————————————–
ONT  Rx power    Tx power    OLT Rx ONT  Temperature  Voltage     Current
ID   (dBm)       (dBm)       power(dBm)  (C)          (V)         (mA)
—————————————————————————–
4  -23.10      2.30        -24.21      56           3.260       13
6  -21.08      2.28        -21.49      44           3.240       13

CHECKING ONT VERSION

OL01#display ont version 0 1 0 4
————————————————————————–
F/S/P                    : 0/1/0
ONT-ID                   : 4
Vendor-ID                : HWTC
ONT Version              : 49
Product-ID               : 4
Equipment-ID             : 24
Main Software Version    : V3R0
Standby Software Version : V3R0
OntProductDescription    : EchoLife
Support XML Version      : 1.3.
OL01#

CHECKING ONT IP (ROUTING MODE)

OL01#display ont wan-info 0/1 0 4
———————————————————————
F/S/P                      : 0/1/0
ONT ID                     : 4
———————————————————————
Index                      : 1
Name                       : OLT_C_INTERNET_DHCP_WAN
Service type               : Internet
Connection type            : IP routed
IPv4 Connection status     : Connected
IPv4 access type           : DHCP
IPv4 address               : 1.2.3.4
Subnet mask                : 255.255.255.0
Default gateway            : 1.2.3.1
Manage VLAN                : 212
Manage priority            : 0
Option60                   : Yes
Switch                     : Enable
MAC address                : BBBB-AAAA-CCCC
Priority policy            : Specified
L2 encap-type              : IPoE
IPv4 switch                : Enable
IPv6 switch                : Disable
———————————————————————
OL01#

CHECKING ONT PORT STATUS

OL01#config
OL01(config)#interface gpon 0/1

OL01(config-if-gpon-0/1)#display ont port state 0 4 eth-port all

————————————————————————–
ONT-ID   ONT      ONT       Speed(Mbps)   Duplex   LinkState  RingStatus
port-ID  Port-type
————————————————————————–
4         1         GE –             –        down       –
4         2         GE 100           full     up         –
4         3         GE –             –        down       –
4         4         GE –             –        down       –
————————————————————————–
OL01(config-if-gpon-0/1)#

CHECKING ONT CONFIGURATION

OL01#display current-configuration ont 0/1/0 4
#
[gpon]
<gpon-0/1>
interface gpon 0/1
ont add 0 4 sn-auth “ABCDEF” omci ont-lineprofile-id 5
ont-srvprofile-id 1 desc “HULK”
ont ipconfig 0 4 dhcp vlan 212 priority
ont internet-config 0 4 ip-index 0
ont wan-config 0 4 ip-index 0 profile-id 1
ont port route 0 4 eth 1 enable –> routing mode

ont port native-vlan 0 4 eth 2 vlan 122 priority 0  –> bridging mode

ont port native-vlan 0 4 eth 3 vlan 122 priority 0  –> bridging mode

ont port route 0 4 eth 4 enable –> routing mode

#
[bbs-config]
<bbs-config>
service-port 2677 vlan 212 gpon 0/1/0 ont 4 gemport 1 multi-service user-
vlan  212 tag-transform translate inbound traffic-table index 20 outbound
traffic-table index 20
service-port 2678 vlan 122 gpon 0/1/0 ont 4 gemport 2 multi-service user-
vlan  122 tag-transform translate inbound traffic-table index 0 outbound
traffic-table index 0
return
OL01#
CHECKING ONT CONFIGURATION PER-PORT
OL01#display current-configuration port 0/1/1
#
[gpon]
<gpon-0/1>
interface gpon 0/1
port 1 ont-auto-find enable –> Configuring this to detect your unregister
ONU automatically

CHECKING HOW MANY SERVICES PER-ONT

OL01#display service-port port 0/1/0 ont 4
{ <cr>|e2e<K>|gemport<K>|sort-by<K> }:

Command:
display service-port port 0/1/0 ont 4
Switch-Oriented Flow List
—————————————————————————–
INDEX VLAN VLAN     PORT F/ S/ P VPI  VCI   FLOW  FLOW       RX   TX  
STATE
ID   ATTR     TYPE                    TYPE  PARA
—————————————————————————–
2677  212 common   gpon 0/1 /0  4    1     vlan  212        20   20   up
2678  122 common   gpon 0/1 /0  4    2     vlan  122        0    0    up
—————————————————————————–
Total : 2  (Up/Down :    2/0)
Note : F–Frame, S–Slot, P–Port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,

OL01#

YOU CAN PING FROM YOUR ONT :P

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont remote-ping 0 4 ip-address 8.8.8.8
OL01(config-if-gpon-0/1)#
—————————————–
ONT remote-ping information
—————————————–
F/S/P                : 0/ 1/0
ONT-ID               : 4
ONT IP Index         : 0
IP address of ping   : 8.8.8.8
Transmit packets     : 4
Receive packets      : 4
Lost packets         : 0
Lost packets ratio(%): 0
Min delay(ms)        : 31
Max delay(ms)        : 31
Average delay(ms)    : 31
Error Code           : –
—————————————–

REBOOT ONT
OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont reset 0 4

RESET FACTORY ONT

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont factory-setting-restore 0 4

HOW TO RELEASE RENEW ONT AS DHCP CLIENT

OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont ipconfig 0 4 dhcp reset

CHECKING RX LEVEL FOR OLT UPLINK

OL01#config
OL01(config)#interface giu 0/18
OL01(config-if-giu-0/18)#display port ddm-info 0
Temperature(C)                       : 38.640000
Supply voltage(V)                    : 3.260000
TX bias current(mA)                  : 38.000000
TX power(dBm)                        : 1.095110
RX power(dBm)                        : -14.659738
OL01(config-if-giu-0/18)#quit
OL01(config)#quit
OL01#

RESET SLOT
OL01#config

OL01(config)#board reset 0/1

HOW TO FIND ONT BY MAC

OL01#display location aaaa-bbbb-cccc
{ <cr>|fabric<K>|ont<K> }:

Command:
display location 4cf9-5dd3-1914
It will take several minutes, and console may be timeout, please use
command  idle-timeout to set time limit
Are you sure to query MAC address location ? (y/n)[n]:y
———————————————————————–
SRV-P BUNDLE TYPE MAC            MAC TYPE F /S /P   VPI  VCI   VLAN
ID
INDEX INDEX
———————————————————————–
5493     –  gpon aaaa-bbbb-cccc dynamic  0 /6 /6   50   1         203
———————————————————————–

If U want to Explore More about other, My advice is using “?” symbol.

I Hope this article can help you sometime.

 
SHARE THIS:

 Twitter

 Facebook

Loading...
RELATED

GPON – Basic Command OLT ZTEMarch 29, 2017In "GPON"

GPON – BASIC COMMAND OLT ALCATEL LUCENT (ALU)June 22, 2017In "ALU"

HOW TO REGISTER ONT HUAWEIJune 21, 2017In "GPON"

POSTED IN GPON, HUAWEI.TAGGED #GPON #HUAWEI.

66 THOUGHTS ON “GPON – BASIC COMMAND

OLT HUAWEI”

1. PHAI VONE

SEPTEMBER 19, 2017 AT 8:08 PM

Thank you very much

Like

REPLY

2. ANDERSON ANAEL
 JANUARY 3, 2018 AT 4:56 AM

very important all command for OLT Huawei, tks a lot. Please, create article for
configuration OLT Huawei MA5600T how-to

Liked by 1 person

REPLY

1. NETWORKINGFROMZERO

JANUARY 3, 2018 AT 2:08 AM

you’re welcome.. please see my other article.. how to register ont huawei..that’s how to
create service

Like

REPLY

2. NETWORKINGFROMZERO

JANUARY 3, 2018 AT 8:02 AM

https://networkingfromzero.wordpress.com/2017/06/21/how-to-register-ont-huawei/

Like

REPLY

3. ANDERSON ANAEL

JANUARY 3, 2018 AT 8:20 PM

my difficulty is being configure the OLT to work with the uplink port. I’m using the GICF
0/18 0 and VLAN150 board, my difficulty is being understand where tcon, gem, profile
 …. my goal is to just test in my office and leave OLT configured, tks a lot for all
information

Like

REPLY

1. NETWORKINGFROMZERO

JANUARY 4, 2018 AT 1:08 AM

okay please try it and just modify vlan from my article.. i hope that’s configuration will be
working..if any problem.. you can share here.. maybe i can help..

Like

REPLY

2. ASKA

NOVEMBER 1, 2018 AT 8:25 AM

This is Aska. Are you still looking for products of Huawei, FiberHome & ZTE 100%
original and new. GEPON ONU, OLT, Fiber CPE,WiFi module,service Board,optic
accessories. you will earn more profits to stronger your business by selling our competitive
price products. Please contact me. Thx. Add my WhatsApp +8613560106987

Like

REPLY

4. MARK

JANUARY 9, 2018 AT 6:16 AM

Hello,
i got the script for changing traffic table
 display traffic table ip from-index 0
then
service-port inbound traffice-table index outbound traffice-table index
i change it to both service-port and
the download rate changes, but the upload remain.
can you please assist me why is that?
thank you!

Like

REPLY

1. NETWORKINGFROMZERO

JANUARY 9, 2018 AT 6:54 AM

can you share full configuration about traffic table and service-port inbound above?

Like

REPLY

1. NOKIE

JANUARY 9, 2018 AT 7:40 AM

————————————————
TD Index : 21
TD Name :
Priority : 0
Copy Priority : –
Mapping Index : –
CTAG Mapping Priority: –
CTAG Mapping Index : –
CTAG Default Priority: 0
Priority Policy : local-pri
CIR : 153600 kbps
CBS : 4917200 bytes
PIR : 512000 kbps
PBS : 682750 bytes
 Fix : 0 kbps
CAR Threshold Profile: –
Color Mode : color-blind
Color Policy : dei
Referenced Status : used
————————————————

Like

2. NETWORKINGFROMZERO

JANUARY 9, 2018 AT 11:12 AM

maybe u can configure like this :

UAWEI#display traffic table ip index 21

————————————————
TD Index : 21
TD Name : ip-traffic-table_21
Priority : 0
Copy Priority : –
Mapping Index : –
CTAG Mapping Priority: –
CTAG Mapping Index : –
CTAG Default Priority: 0
Priority Policy : local-pri
CIR : 153600 kbps
CBS : 4917200 bytes
PIR : 153600 kbps
PBS : 4917200 bytes
Fix : 0 kbps
CAR Threshold Profile: –
Color Mode : color-blind
Color Policy : dei
Referenced Status : used
————————————————

HUAWEI#

######################################################
HUAWEI#display traffic table ip index 22
————————————————
TD Index : 22
TD Name : ip-traffic-table_22
Priority : 0
Copy Priority : –
Mapping Index : –
CTAG Mapping Priority: –
CTAG Mapping Index : –
CTAG Default Priority: 0
Priority Policy : local-pri
CIR : 512000 kbps
CBS : 682750 bytes
PIR : 512000 kbps
PBS : 682750 bytes
Fix : 0 kbps
CAR Threshold Profile: –
Color Mode : color-blind
Color Policy : dei
Referenced Status : used
————————————————

HUAWEI#

##################

service-port xxxxx inbound traffic-table index 21 outbound traffic-table index 22