50W Single Output DC-DC Converter SD-50 series

■ Features :
‧2:1 wide input range
‧Protections: Short circuit / Overload / Over voltage
‧1500VAC I/O isolation
‧Built-in EMI filter, low ripple noise
‧100% full load burn-in test
‧Fixed switching frequency at 83KHz
‧Low cost
‧High reliability
‧2 years warranty

SPECIFICATION
MODEL SD-50A-5 SD-50B-5 SD-50C-5 SD-50A-12 SD-50B-12 SD-50C-12 SD-50A-24 SD-50B-24 SD-50C-24
DC VOLTAGE 5V 12V 24V
RATED CURRENT 10A 4.2A 2.1A
CURRENT RANGE 0 ~ 10A 0 ~ 4.2A 0 ~ 2.1A
RATED POWER 50W 50.4W 50.4W
RIPPLE & NOISE (max.) Note.2 100mVp-p 120mVp-p 150mVp-p
OUTPUT
VOLTAGE ADJ. RANGE 4.5 ~ 5.5VDC 11 ~ 16VDC 23 ~ 30VDC
VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.3% ±0.2%
LOAD REGULATION ±0.5% ±0.3% ±0.2%
SETUP, RISE, HOLD UP TIME 2.5s, 50ms, ------ at full load
VOLTAGE RANGE A:9.2 ~ 18VDC B:19 ~ 36VDC C:36 ~ 72VDC
INPUT EFFICIENCY (Typ.) 70% 73% 76% 72% 75% 78% 74% 80% 83%
DC CURRENT 7A/12V 3A/24V 1.5A/48V 7A/12V 3A/24V 1.5A/48V 7A/12V 3A/24V 1.5A/48V
105 ~ 150% rated output power
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION
5.75 ~ 6.75V/10% load 16.8 ~ 20V/10% load 31.5 ~ 37.5V/10% load
OVER VOLTAGE
Protection type : Hiccup mode, recovers automatically after fault condition is removed
WORKING TEMP. -10 ~ +60℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS Design refer to LVD
SAFETY & WITHSTAND VOLTAGE I/P-O/P:1.5KVAC I/P-FG:2.0KVAC O/P-FG:0.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
(Note 4) EMC EMISSION Compliance to EN55022 (CISPR22) Class B
EMC IMMUNITY Compliance to EN61000-4-2,3,4,6,8, EN55024, heavy industry level, criteria A
MTBF 365.6K hrs min.(SD-50A) 357.5K hrs min.(SD-50B) 368.5K Hrs min.(SD-50C) MIL-HDBK-217F (25℃)
OTHERS DIMENSION 159*97*38mm (L*W*H)
PACKING 0.48Kg; 24pcs/12.7Kg/0.75CUFT
1. All parameters NOT specially mentioned are measured at 12,24,48VDC input, rated load and 25℃ of ambient temperature.
NOTE
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)

File Name:SD-50-SPEC 2015-05-29

 50W Single Output DC-DC Converter SD-50 series

Mechanical Specification Case No. 901 Unit:mm

152.5

4.5
24 78
159

6.5 150

Terminal Pin No. Assignment

Pin No. Assignment Pin No. Assignment
1 DC INPUT V+ 4 DC OUTPUT -V
2 DC INPUT V- 5 DC OUTPUT +V
3 FG
22 117

Block Diagram
fosc : 83KHz

EMI POWER RECTIFIERS +V

I/P FILTER &
SWITCHING -V
FILTER

FG DETECTION
PWM CIRCUIT
O.L.P.
CONTROL

O.V.P.

Derating Curve Static Characteristics(SD-50C-24V)

SD-50B,C 32 350
100
28 300
80
24 250
SD-50A
60 20 200

16 150
40
12 100
20
8 50

-10 0 10 20 30 40 50 60 (VERTICAL) 25 30 35 40 45 50 55 60 65 70 72
-10 0 45 55 (HORIZONTAL)

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V)

File Name:SD-50-SPEC 2015-05-29