Scribd
Upload
57 views

SDD - Set A

This document contains a model examination for a structural design and drawing course. It consists of 5 questions related to designing various civil engineering structures like retaining walls, interior panels, water tanks, steel roof trusses, plate girders, and foundations. The questions provide specifications for the structures and ask students to design the structures based on the given parameters, limiting states, and material grades. Students are to show calculations and sketches as needed to demonstrate their structural design solutions.

Uploaded by

rishinathnehru
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
57 views

SDD - Set A

This document contains a model examination for a structural design and drawing course. It consists of 5 questions related to designing various civil engineering structures like retaining walls, interior panels, water tanks, steel roof trusses, plate girders, and foundations. The questions provide specifications for the structures and ask students to design the structures based on the given parameters, limiting states, and material grades. Students are to show calculations and sketches as needed to demonstrate their structural design solutions.

Uploaded by

rishinathnehru
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

OM SA

ADHIPARASAKTHI COLLEGE OF ENGINEERING


G.B.NAGAR, KALAVAI – 632 506. RANIPET DISTRICT
MODEL EXAMINATION
Set A
Department : CIVIL Year/Semester : IV/VII
Subject Code : CE8703 Date of Exam : 30.11.2022
Subject Title : STRUCTURAL DESIGN & Max. Marks : 100
DRAWING
PART-A
1. a) Design a Cantilever Retaining wall at the height of earth embankment 20
is 4m and angle of internal friction φ=300,unit weight of soil is γ=18
KN/m3.Take co-efficient of friction factor of soil and
concrete=0.6,then SBC=200 KN/m2.Using M20 and Fe415 grades.
(OR)
b) Design a Stem based on Counterfort retaining wall and the height of 20
earth embankment is 5m and SBC of soil is 180 KN/m 2 and then angle
of internal friction φ=300.Take yield weight of soil is 18 KN/m3. Using
M20and fe415 grades and assume spacing of counterfort is 3m.
2. a) Design a Interior panel has a size of 5m x 5m and use M20and fe415 20
grades. Design column head and drops.
(OR)
b) Design a Interior panel has a size of 4.5m x 6m(inner dimension) of a 20
reinforce concrete building. Assume live load 4 KN/m2 and floor
finishing 1 KN/m2.Sketch the reinforcement details, concrete of grade
M20 and fe415 grades. Adopt limit state method of design.
3. a) A Reinforced concrete water tank resting on ground in 5mx3m with a 20
max depth of 3m, use M20 grade of concrete and Fe415. design water
tank.
(OR)
b) Design an underground tank of internal dimensions 8 m x 2 m x 2 m. 20
the soil Surrounding the tank is likely to get wet. Angle of repose of
soil in dry state is 300and in wet state is 60 soil weight 20kN/m3.
4. a) Determine the design load on the Purlin of the industrial building near 20
Vishakhapatnam give clause of building general the life of 50 years.
Terrain category II, max dimension 40m, width of building 15m,
height of the elevation level-8m, topography-θ less than 3 0,
permeability medium, span of truss-15m, pitch-1/5, sheeting-AC sheet,
spacing of truss 4m, spacing of purlin 1.35m.
(OR)
b) Design a Steel Roof Truss to suit the following data: 20
Span of truss-10m, type-fan type, roof cover-GC, materials-rolled steel
angles, spacing of the roof truss-4.5m, wind pressure=1.0kN/m2.draw
the elevation of roof truss and details of joints.
5. a) Design a Welded Plate Girder of 25m span to support a Uniformly 20
Distributed Live load of 80kN/m over the span. Assume required data.
(OR)
b) Built-up Steel Column of two ISWM400 RSJ with their webs spaced 20
at 375mm transmits a factored axial load of 3000kN.The joist are
connected by 10mm thick battens. Safe bearing capacity of the soil is
300kN/m2. fck=25N/mm2 is used for the foundation bed. permissible
compressive stress in concrete=4N/mm2.Design a suitable slab base
Course Teacher Staff Department QP Prepared By
P.Mohanapriya CIVIL ENGINEERING P.Mohanapriya
foundation for the column and sketch the details of the foundation.

Course Teacher Staff Department QP Prepared By


P.Mohanapriya CIVIL ENGINEERING P.Mohanapriya

You might also like