Scribd
Upload
250 views2 pages

Pivothead Eyewear Quick Start Guide

This document provides instructions for using Pivothead smart glasses: 1) Turn the glasses on by pressing the power button, check that the blue LED lights up 2) Record a video by pressing the forward part of the pivot switch, indicated by a blinking red LED 3) Take a picture with a short press of the back part of the pivot switch, shown by a blinking red LED pattern 4) Charge the glasses by connecting the USB cable to a computer or wall charger, indicated by solid green and flashing blue lights

Uploaded by

Rodrigo Casas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
250 views2 pages

Pivothead Eyewear Quick Start Guide

This document provides instructions for using Pivothead smart glasses: 1) Turn the glasses on by pressing the power button, check that the blue LED lights up 2) Record a video by pressing the forward part of the pivot switch, indicated by a blinking red LED 3) Take a picture with a short press of the back part of the pivot switch, shown by a blinking red LED pattern 4) Charge the glasses by connecting the USB cable to a computer or wall charger, indicated by solid green and flashing blue lights

Uploaded by

Rodrigo Casas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Pivothead Eyewear Quick Start Guide

Last Updated: Dec 04, 2014 12:19PM MST

The Basics
Step 1: Turn on your Pivotheads.
 Locate the power button (A) which located on the bottom of the left ear piece.
 Press the power button (a short press). That's it! Boom.
 You should now see a blue light on the LED status indicator (B). Great success.
 If the blue light is not on - try plugging your Pivotheads in - they probably need to be charged.
 To turn off your Pivotheads, just push the same button.

Step 2: Record a Video.


 Locate the Pivot switch and press the forward part (C)
 You should now see both the blue power LED + a blinking red LED (B).
 Congrats - you are now recordng a video!
 To stop recording simply push the forward portion of the Pivot switch again and make sure the red LED stops
blinking.
 Oh snap - you've just recorded a video. (hopefully it was a good one).

Step 3: Take a Picture.


 Locate the Pivot switch and press (short press) the back part (D).
 The red LED (B) - will blink once quickly, and once slowly.
 Congrats - you just took an 8 megapixel snapshot!

Step 4: Charging Your Pivothead


 Plug the Pivothead glasses into a computer or a wall charger using the USB cable found in the case
 A solid green light and a flashing blue light will mean the glasses are charging.
 A solid green light means the glasses are finished charging.
Step 5: Retrieving your Videos and Pictures
 Plug the Pivothead glasses into a computer using the USB cable and turn on the glasses by holding the power
button (A)
 A solid red, green, and blue light will show that the Pivothead is connected
 Now go to start, Computer, and select the Pivothead glasses.

 Double click on DCIM folder

 Double Click on 100HDHFR Folder

 Drag a drop desired pictures and videos into preffered storage location

General Trouble Shooting


Other LED Meanings
Sometimes you might see your glasses' LED blinking. Here's what they are trying to tell you.
 If the blue and red light are blinking - your Pivotheads' memory is full.
 If the blue light is blinking slowly your battery is low (less than 10%).
 If the blue light is blinking quickly your battery is gone, baby - and your glasses will soon shut off.
http://support.pivothead.com/customer/portal/articles/1253941-pivothead-eyewear-quick-start-guide
http://support.pivothead.com/customer/portal/articles/1253819-how-do-i-charge-my-pivotheads-

You might also like